D-Link SharePort DIR-825 User manual
Publicité
Publicité
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes.
Revision
3.0
Manual Revisions
Date
November 30, 2011
Description
• Initial release for Revision C1
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2011 by D-Link Systems, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Systems, Inc.
D-Link DIR-825 User Manual i
Table of Contents
Table of Contents
Preface.................................................................................. i
L2TP ....................................................................................30
Manual Revisions ........................................................................... i
DS-Lite ...............................................................................32
Trademarks ...................................................................................... i
Wireless Settings .................................................................33
Product.Overview...............................................................1
Package Contents ......................................................................... 1
System Requirements ................................................................. 2
Introduction ................................................................................... 3
Hardware Overview ..................................................................... 5
Connections ........................................................................... 5
LEDs ........................................................................................... 6
Installation..........................................................................7
Before you Begin ........................................................................... 7
Wireless Installation Considerations ...................................... 8
Manual Setup ................................................................................. 9
Connect to an Existing Router ...............................................11
Configuration....................................................................13
Quick Router Setup Wizard (CD) ...........................................13
Quick Setup Wizard ....................................................................15
Web-based Configuration Utility ..........................................21
Internet Connection Setup .............................................22
Static (assigned by ISP) ................................................23
Dynamic (Cable) .............................................................25
PPPoE (DSL) ......................................................................26
PPTP ....................................................................................28
Manual Wireless Settings .................................................34
802.11n/g (2.4GHz) .......................................................34
802.11n/a (5GHz) ...........................................................36
Wireless Security .................................................................38
What is WPA? ...................................................................38
Wireless Security Setup Wizard .................................39
Add Wireless Device with WPS Wizard ...................41
WPA/WPA2-Personal (PSK) .........................................43
Configure WPA/WPA2-Enterprise (RADIUS)..........44
Network Settings ................................................................46
Router Settings ...............................................................46
DHCP Server Settings ...................................................47
DHCP Reservation .........................................................49
Media Server.........................................................................50
Storage ...................................................................................51
IPv6 ..........................................................................................52
IPv6 Internet Connection Setup Wizard ................53
IPv6 Manual Setup.........................................................58
Advanced ...............................................................................67
Virtual Server ...................................................................67
Port Forwarding .............................................................68
Application Rules ...........................................................69
QoS Engine .......................................................................70
D-Link DIR-825 User Manual ii
Table of Contents
Network Filters ................................................................71
Access Control .................................................................72
Website Filters .................................................................75
Inbound Filters ................................................................76
Firewall Settings .............................................................77
Routing ..............................................................................79
Advanced Wireless ........................................................80
Wi-Fi Protected Setup (WPS) .....................................81
Advanced Network Settings ......................................83
Guest Zone .......................................................................84
IPv6 Firewall .....................................................................85
IPv6 Routing ....................................................................86
Tools ........................................................................................87
Admin.................................................................................87
Time ....................................................................................88
SysLog ................................................................................89
Email Settings..................................................................90
System ...............................................................................91
Firmware ...........................................................................92
Language Pack ................................................................92
Dynamic DNS ..................................................................93
System Check ..................................................................95
Schedules .........................................................................96
Status ......................................................................................97
Device Info .......................................................................97
Logs.....................................................................................98
Statistics ............................................................................99
Internet Sessions ......................................................... 100
Routing ........................................................................... 101
Wireless........................................................................... 102
IPv6 .................................................................................. 103
IPV6 Routing ................................................................. 104
Support ............................................................................... 105
Connect.a.Wireless.Client.to.your.Router.....................106
WPS Button ................................................................................ 106
Windows® 7 ................................................................................ 107
WPA/WPA2 ......................................................................... 107
WPS ....................................................................................... 110
Windows Vista® ......................................................................... 114
WPA/WPA2 ......................................................................... 115
WPS/WCN 2.0 .................................................................... 117
Windows® XP ............................................................................. 118
WPA/WPA2 ......................................................................... 119
Troubleshooting.............................................................121
Wireless.Basics................................................................125
What is Wireless? ...................................................................... 126
Wireless Modes ......................................................................... 129
Networking.Basics..........................................................130
Check your IP address ............................................................ 130
Statically Assign an IP address ............................................ 131
D-Link DIR-825 User Manual iii
Table of Contents
Technical.Specifications.................................................132
Contacting.Technical.Support.......................................133
GPL.Code.Statement......................................................134
Warranty..........................................................................146
Registration....................................................................153
D-Link DIR-825 User Manual iv
Section 1 - Product Overview
DIR-825 Xtreme N® Dual Band Gigabit Router
Ethernet Cable
Two Detachable Antennas
Power Adapter
CD-ROM with Manual and Setup Wizard
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage rating than the one included with the DIR-825 will cause damage and void the warranty for this product.
D-Link DIR-825 User Manual 1
Section 1 - Product Overview
System Requirements
Network.Requirements
Web-based.Configuration.
Utility.Requirements
CD.Installation.Wizard.
Requirements
• An Ethernet-based Cable or DSL modem
• IEEE 802.11n or 802.11g wireless clients
• IEEE 802.11a wireless clients
• 10/100/1000 Ethernet
Computer.with.the.following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Browser.Requirements:
• Internet Explorer 6 or higher
• Firefox 3.0 or higher
• Safari 3.0 or higher
• Chrome 2.0 or higher
Windows
®
.Users: Make sure you have the latest version of Java installed. Visit www.java.com
to download the latest version.
Computer.with.the.following:
• Windows® 7, Vista®, or XP (Service Pack 2 or higher)
• An installed Ethernet adapter
• CD-ROM drive
D-Link DIR-825 User Manual 2
Section 1 - Product Overview
Introduction
TOTAL.PERFORMANCE
Combines award winning router features and IEEE 802.11a/g/n wireless technology to provide the best wireless performance.
TOTAL.SECURITY
The most complete set of security features including Active Firewall and WPA/WPA2 to protect your network against outside intruders.
TOTAL.COVERAGE
Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
ULTIMATE.PERFORMANCE
The D-Link Xtreme N® Dual Band Gigabit Router (DIR-825) is a 802.11n/802.11a compliant device that delivers real world performance of up to 14x faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection). Create a secure wireless network to share photos, files, music, video, printers, and network storage throughout your home. Connect the DIR-825 router to a cable or DSL modem and share your high-speed Internet access with everyone on the network. In addition, this Router includes a Quality of Service (QoS) engine that keeps digital phone calls (VoIP) and online gaming smooth and responsive, providing a better Internet experience.
EXTENDED.WHOLE.HOME.COVERAGE
Powered by Wireless N technology, this high performance router provides superior Whole Home Coverage while reducing dead spots.
The router is designed for use in bigger homes and for users who demand higher performance networking. Add a Wireless N notebook or desktop adapter and stay connected to your network from virtually anywhere in your home.
TOTAL.NETWORK.SECURITY
The Wireless N router supports all of the latest wireless security features to prevent unauthorized access, be it from over the wireless network or from the Internet. Support for WPA/WPA2 standards ensure that you’ll be able to use the best possible encryption method, regardless of your client devices. In addition, this router utilizes dual active firewalls (SPI and NAT) to prevent potential attacks from across the Internet.
* Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.
D-Link DIR-825 User Manual 3
Section 1 - Product Overview
Features
•.Faster.Wireless.Networking - The DIR-825 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 14x faster than 802.11g.
•.Compatible.with.802.11a/g.Devices - The DIR-825 is still fully compatible with the IEEE 802.11g and 802.11a standards, so it can connect with existing 802.11g and 802.11a PCI, USB, and Cardbus adapters.
•.Advanced.Firewall.Features - The Web-based user interface displays a number of advanced network management features including:
• Content.Filtering - Easily applied content filtering based on MAC Address, URL, and/or Domain
Name.
• Filter.Scheduling - These filters can be scheduled to be active on certain days or for a duration of hours or minutes.
• Secure.Multiple/Concurrent.Sessions - The DIR-825 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-825 can securely access corporate networks.
•.User-friendly.Setup.Wizard - Through its easy-to-use Web-based user interface, the DIR-825 lets you control what information is accessible to those on the wireless network, whether from the Internet or from your company’s server. Configure your router to your specific settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g, 802.11a, and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.
D-Link DIR-825 User Manual 4
Section 1 - Product Overview
Hardware Overview
Connections
1 2 3 4 5 6
1
LAN Ports (1-4) Connect 10/100/1000 Ethernet devices such as computers, switches, and NAS.
2
3
4
Internet Port
USB Port
The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem.
Connect a USB 1.1 or 2.0 flash drive to configure the wireless settings using WCN and SharePort. SharePort allows you to share a printer or storage device with your local network.
Power Button Press the power button to power on and off.
5
Reset Button Pressing the Reset button restores the router to its original factory default settings.
6
Power Receptor Receptor for the supplied power adapter.
D-Link DIR-825 User Manual 5
Section 1 - Product Overview
Hardware Overview
LEDs
1 2 3 4
5 6
1
2
Power LED
Internet LED
3
WLAN LED (2.4GHz)
4
5
6
WLAN LED (5GHz)
LAN LEDs (1-4)
WCN/USB LED
A solid light indicates a proper connection to the power supply.
A solid light indicates connection on the Internet port. This LED blinks during data transmission.
A solid light indicates that the 2.4GHz wireless segment is ready. This LED blinks during wireless data transmission.
A solid light indicates that the 5GHz wireless segment is ready. This LED blinks during wireless data transmission.
A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission.
Insert a USB flash drive with WCN information. The LED will blink 3 times when it successfully transfers the wireless settings. This LED is also for SharePort.
D-Link DIR-825 User Manual 6
Section 2 - Installation
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Before you Begin
• Please configure the router with the computer that was last connected directly to your modem.
• You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
• If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet,
Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.
• When running the Setup Wizard from the D-Link CD, make sure the computer you are running the CD from is connected to the Internet and online or the wizard will not work. If you have disconnected any hardware, re-connect your computer back to the modem and make sure you are online.
D-Link DIR-825 User Manual 7
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not in use.
D-Link DIR-825 User Manual 8
Section 2 - Installation
Manual Setup
Important: for best results, insert the Installation CD and follow the on-screen instructions. If you are unable to use the CD or are using Mac or Linux, please use the following installation steps:
1. Turn off and unplug your cable or DSL broadband modem. This is required.
modem
2. Position your router close to your modem and a computer. Place the router in an open area of your intended work area for better wireless coverage.
3. Unplug the Ethernet cable from your modem (or existing router if upgrading) that is connected to your computer.
Plug it into the blue port labeled 1 on the back of your router. The router is now connected to your computer.
4 3 LAN 2 1
DIR-825
INTERNET USB
RESET
12V - - - 2A
computer
D-Link DIR-825 User Manual 9
Section 2 - Installation
4. Plug one end of the included blue Ethernet cable that came with your router into the yellow port labeled
INTERNET on the back of the router. Plug the other end of this cable into the Ethernet port on your modem.
4 3 LAN 2 4
DIR-825
INTERNET USB
RESET
12V - - 2A
modem
5. Reconnect the power adapter to your cable or DSL broadband modem and wait for two minutes.
6. Connect the supplied power adapter into the power port on the back of the router and then plug it into a power outlet or surge protector. Press the power button and verify that the power LED is lit. Allow 1 minute for the router to boot up.
4 3 LAN 2 1
DIR-825
INTERNET USB
RESET
12V - - - 2A
7. If you are connecting to a Broadband service that uses a dynamic connection (not PPPoE), you may be online already. Try opening a web browser and enter a web site. If you connect, you are finished with your Internet setup.
Please skip to page 13 to configure your router and use the manual setup procedure to configure your network and wireless settings. If you did not connect to the Internet, use the D-Link Setup Wizard (refer to page 15).
D-Link DIR-825 User Manual 10
Section 2 - Installation
Connect to an Existing Router
Note: It is strongly recommended to replace your existing router with the DIR-825 instead of using both. If your modem is a combo router, you may want to contact your ISP or manufacturer’s user guide to put the router into Bridge mode, which will ‘turn off’ the router (NAT) functions.
If you are connecting the DIR-825 router to an existing router to use as a wireless access point and/or switch, you will have to do the following to the DIR-825 before connecting it to your network:
• Disable UPnP
™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the Networking.Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.
2. Open a web browser, enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to
Admin and leave the password box empty. Click Log.In to continue.
3. Click on Advanced and then click Advanced.Network. Uncheck the Enable.UPnP checkbox. Click Save.Settings to continue.
4. Click Setup and then click Network.Settings. Uncheck the Enable.DHCP.Server checkbox. Click Save.Settings to continue.
D-Link DIR-825 User Manual 11
Section 2 - Installation
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save.Settings to save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as in Step 1.
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router.
8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network.
Laptop
Computer
Existing Router
Modem
Internet
1 2 LAN 3 4
DIR-825
INTERNET USB
RESET
12V - - - 3A
D-Link DIR-825 User Manual 12
Section 2 - Installation
Configuration
There are several different ways you can configure your router to connect to the Internet and connect to your clients:
• Quick.Router.Setup.Wizard.- Insert the supplied CD and launch the setup wizard (see below).
• D-Link.Setup.Wizard - This wizard will launch if you do not run the CD wizard and log into the router for the first time.
Refer to page 15.
• Manual.Setup - Log into the router and manually configure your router (advanced users only). Refer to page 21.
Quick Router Setup Wizard (CD)
To run the
Quick.Router.Setup.Wizard, insert the CD in the CD-ROM drive. When the autorun screen appears, click English
(or French), and then click the Install button.
Note: If the CD Autorun function does not automatically start on your computer, go to Start > Run. In the run box type D:\autorun.exe
(where D: represents the drive letter of your CD-ROM drive).
D-Link DIR-825 User Manual 13
Section 3 - Configuration
When the Wizard appears, select your language from the drop-down menu and then click Next to continue. Follow the on-screen instructions to configure your router.
Once you are finished, you may skip to page 21 and will be able to log into the web-based configuration utility and configure more advanced features.
D-Link DIR-825 User Manual 14
Section 3 - Configuration
Quick Setup Wizard
If this is your first time installing the router, open your web browser. You will automatically be directed to the Wizard Setup
Screen.
If you have already configured your settings and you would like to access the configuration utility, please refer to page 21.
If you did not run the setup wizard from the CD and this is the first time logging into the router, this wizard will start automatically.
This wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the
Internet.
Click Next to continue.
D-Link DIR-825 User Manual 15
Section 3 - Configuration
Please wait while your router detects your internet connection type.
If the router detects your Internet connection, you may need to enter your ISP information such as username and password.
If the router does not detect a valid Ethernet connection from the
Internet port, this screen will appear. Connect your broadband modem to the Internet port and then click Try.Again.
If the router detects an Ethernet connection but does not detect the type of Internet connection you have, this screen will appear. Click Guide.me.
through.the.Internet.Connection.Settings to display a list of connection types to choose from.
D-Link DIR-825 User Manual 16
Section 3 - Configuration
Select your Internet connection type and click Next to continue.
If the router detected or you selected PPPoE, enter your PPPoE username and password and click Next to continue.
Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
If the router detected or you selected PPTP, enter your PPTP username, password, and other information supplied by your ISP. Click Next to continue.
D-Link DIR-825 User Manual 17
Section 3 - Configuration
If the router detected or you selected L2TP, enter your L2TP username, password, and other information supplied by your ISP. Click Next to continue.
If the router detected or you selected Static, enter the IP and DNS settings supplied by your ISP. Click Next to continue.
D-Link DIR-825 User Manual 18
Section 3 - Configuration
For both the 2.4GHz and 5GHz segments, create a wireless network a name (SSID) using up to 32 characters.
Create a wireless security passphrase or key (between 8-63 characters).
Your wireless clients will need to have this passphrase or key entered to be able to connect to your wireless network.
Click Next to continue.
In order to secure your router, please enter a new password. Check the
Enable Graphical Authentication box to enable CAPTCHA authentication for added security. Click Next to continue.
Select your time zone from the drop-down menu and click Next to continue.
D-Link DIR-825 User Manual 19
Section 3 - Configuration
The Setup Complete window will display your wireless settings. Click
Save.and.Connect to continue.
If you want to create a bookmark to the router, click OK. Click Cancel if you do not want to create a bookmark.
If you clicked Yes, a window may appear (depending on what web browser you are using) to create a bookmark.
The router will now reboot. Please allow a minute or two. Click the
Continue button once it is active.
D-Link DIR-825 User Manual 20
Section 3 - Configuration
Web-based Configuration Utility
To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router
(http://192.168.0.1).
Windows and Mac users may also connect by typing
http://dlinkrouter or http://dlinkrouter.local.in the address bar.
Select Admin from the drop-down menu and then enter your password. Leave the password blank by default.
D-Link DIR-825 User Manual 21
Section 3 - Configuration
Internet Connection Setup
Click Manual.Internet.Connection.Setup to configure your connection manually and continue to the next page.
If you want to configure your router to connect to the Internet using the wizard, click Internet.Connection.Setup.Wizard.
You will be directed to the Quick Setup Wizard. Please skip to page 15.
D-Link DIR-825 User Manual 22
Section 3 - Configuration
Manual Internet Setup
Static (assigned by ISP)
Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
My Internet Connection:
Select Static.IP to manually enter the IP settings supplied by your ISP.
Enable Advanced DNS
Service:
Advanced Domain Name System (DNS) services enhances your
Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.
Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.
Enable True Gigabit
Routing Connectivity:
Check to enable true Gigabit routing. This will increase the through-put of the WAN-LAN connectivity of the router.
IP Address:
Enter the IP address assigned by your ISP.
Subnet Mask:
Enter the Subnet Mask assigned by your ISP.
Default Gateway:
Enter the Gateway assigned by your ISP.
DNS Servers:
The DNS server information will be supplied by your ISP (Internet
Service Provider.)
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU.
D-Link DIR-825 User Manual 23
Section 3 - Configuration
MAC Address:
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Copy.Your.PC’s.MAC.Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
D-Link DIR-825 User Manual 24
Section 3 - Configuration
Dynamic (Cable)
My Internet
Connection:
Select Dynamic. IP. (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services.
Enable Advanced
DNS Service:
Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.
Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.
Enable True Gigabit
Routing Connectivity:
Check to enable true Gigabit routing. This will increase the through-put of the WAN-LAN connectivity of the router.
Host Name:
The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure.
Use Unicasting:
Check the box if you are having problems obtaining an IP address from your ISP.
Primary/Secondary
DNS Server:
Enter the Primary and secondary DNS server IP addresses assigned by your ISP. These addresses are usually obtained automatically from your ISP. Leave at 0.0.0.0 if you did not specifically receive these from your ISP.
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU.
MAC Address:
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Copy.Your.PC’s.MAC.Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
D-Link DIR-825 User Manual 25
Section 3 - Configuration
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
My Internet
Connection:
Select
PPPoE.(Username/Password) from the drop-down menu.
Enable
Advanced DNS
Service:
Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.
Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.
Enable True
Gigabit Routing
Connectivity:
Check to enable true Gigabit routing. This will increase the through-put of the WAN-LAN connectivity of the router.
Address Mode:
Select Static.IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.
IP Address:
Enter the IP address (Static PPPoE only).
User Name:
Enter your PPPoE user name.
Password:
Enter your PPPoE password and then retype the password in the next box.
Service Name:
Enter the ISP Service Name (optional).
Reconnect
Mode:
Select either Always-on, On-Demand, or Manual.
D-Link DIR-825 User Manual 26
Section 3 - Configuration
Maximum
Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
DNS
Addresses:
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default
MTU.
MAC Address:
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Copy.Your.PC’s.MAC.Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
D-Link DIR-825 User Manual 27
Section 3 - Configuration
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
My Internet
Connection:
Select PPTP.(Username/Password) from the drop-down menu.
Enable
Advanced DNS
Service:
Advanced Domain Name System (DNS) services enhances your Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.
Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.
Enable True
Gigabit Routing
Connectivity:
Check to enable true Gigabit routing. This will increase the throughput of the WAN-LAN connectivity of the router.
Address Mode:
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.
PPTP IP Address:
Enter the IP address (Static PPTP only).
PPTP Subnet
Mask:
Enter the Primary and Secondary DNS Server Addresses (Static PPTP only).
PPTP Gateway:
Enter the Gateway IP Address provided by your ISP.
PPTP Server IP:
Enter the Server IP provided by your ISP (optional).
D-Link DIR-825 User Manual 28
Section 3 - Configuration
Username:
Enter your PPTP username.
Password:
Reconnect
Mode:
Enter your PPTP password and then retype the password in the next box.
Select either Always-on, On-Demand, or Manual.
Maximum Idle
Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
DNS Servers:
The DNS server information will be supplied by your ISP (Internet Service Provider.)
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
MAC Address:
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the
Clone.Your.PC’s.MAC.Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
D-Link DIR-825 User Manual 29
Section 3 - Configuration
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services.
My Internet
Connection:
Select
L2TP.(Username/Password) from the drop-down menu.
Enable
Advanced DNS
Service:
Advanced Domain Name System (DNS) services enhances your
Internet performance by getting you the information and web pages you are looking for faster and more reliably. In addition, it improves your overall Internet experience by correcting many common typo mistakes automatically, taking you where you intended to go and saving you valuable time.
Disclaimer: D-Link makes no warranty as to the availability, reliability, functionality and operation of the Advanced DNS service or its features.
Enable True
Gigabit Routing
Connectivity:
Check to enable true Gigabit routing. This will increase the through-put of the WAN-LAN connectivity of the router.
Address Mode:
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
L2TP IP Address:
Enter the L2TP IP address supplied by your ISP (Static only).
L2TP Subnet
Mask:
Enter the Subnet Mask supplied by your ISP (Static only).
L2TP Gateway:
Enter the Gateway IP Address provided by your ISP.
L2TP Server IP:
Enter the Server IP provided by your ISP (optional).
D-Link DIR-825 User Manual 30
Section 3 - Configuration
Username:
Enter your L2TP username.
Password:
Enter your L2TP password and then retype the password in the next box.
Reconnect
Mode:
Select either Always-on, On-Demand, or Manual.
Maximum Idle
Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
DNS Servers:
Enter the Primary and Secondary DNS Server Addresses (Static L2TP only).
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is the default
MTU.
Clone MAC
Address:
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the
Clone.Your.PC’s.MAC.Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
D-Link DIR-825 User Manual 31
Section 3 - Configuration
Internet Setup
DS-Lite
Another Internet Connection type is DS-Lite.
DS-Lite is an IPv6 connection type. After selecting DS-Lite, the following parameters will be available for configuration:
DS-Lite
Configuration:
Select the DS-Lite DHCPv6 option to let the router allocate the
AFTR IPv6 address automatically. Select the Manual Configuration to enter the AFTR IPv6 address in manually.
AFTR IPv6
Address:
After selecting the Manual Configuration option above, enter the
AFTR IPv6 address used here.
B4 IPv4 Address: Enter the B4 IPv4 address value used here.
WAN IPv6
Address:
Once connected, the WAN IPv6 address will be displayed here.
IPv6 WAN
Default Gateway
Once connected, the IPv6 WAN Default Gateway address will be displayed here.
D-Link DIR-825 User Manual 32
Section 3 - Configuration
Wireless Settings
If you want to configure the wireless settings on your router using the wizard, click Wireless.Security.Setup.Wizard.and refer to page 38.
Click Add.Wireless.Device.with.WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to page 41.
If you want to manually configure the wireless settings on your router click Manual Wireless.Network.Setup.and refer to the next page.
D-Link DIR-825 User Manual 33
Section 3 - Configuration
Manual Wireless Settings
802.11n/g (2.4GHz)
Enable Wireless:
Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.
Schedule:
Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu.
Click New.Schedule to create a schedule.
Wireless Network
Name:
Service Set Identifier (SSID) is the name of your wireless network. Create a name for your wireless network using up to 32 characters. The SSID is case-sensitive.
802.11 Mode:
Select one of the following:
802.11b.Only - Select only if all of your wireless clients are 802.11b.
802.11g.Only - Select only if all of your wireless clients are 802.11g.
802.11n.Only - Select only if all of your wireless clients are 802.11n.
Mixed.802.11g.and.802.11b - Select if you are using both 802.11g and 802.11b wireless clients.
Mixed.802.11n.and.802.11g - Select if you are using both 802.11n and 802.11g wireless clients.
Mixed.802.11n,.11g,.and.11b - Select if you are using a mix of 802.11n, 802.11g, and 802.11b wireless clients.
Enable Auto
Channel Scan:
The Auto.Channel.Scan setting can be selected to allow the DIR-825 to choose the channel with the least amount of interference.
Wireless Channel:
Indicates the channel setting for the DIR-825. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto.Channel.Scan, this option will be greyed out.
Transmission Rate:
Select the transmit rate. It is strongly suggested to select Best.(Auto) for best performance.
D-Link DIR-825 User Manual 34
Section 3 - Configuration
Channel Width:
Select the Channel Width:
Auto.20/40 - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Visibility Status:
Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-825. If Invisible is selected, the
SSID of the DIR-825 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-825 in order to connect to it.
Wireless Security:
Refer to page 38 for more information regarding wireless security.
D-Link DIR-825 User Manual 35
Section 3 - Configuration
802.11n/a (5GHz)
Enable Wireless:
Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions.
Schedule:
Select the time frame that you would like your wireless network enabled. The schedule may be set to Always.
Any schedule you create will be available in the dropdown menu. Click New.Schedule to create a schedule.
Wireless Network
Name:
Service Set Identifier (SSID) is the name of your wireless network. Create a name for your wireless network using up to 32 characters. The SSID is case-sensitive.
802.11 Mode:
Select one of the following:
802.11a.Only - Select if all of your wireless clients are 802.11a.
802.11n.Only - Select only if all of your wireless clients are 802.11n.
Mixed.802.11n.and.802.11a - Select if you are using both 802.11n and 802.11a wireless clients.
Enable Auto
Channel Scan:
The Auto.Channel.Scan setting can be selected to allow the DIR-825 to choose the channel with the least amount of interference.
Wireless Channel:
Indicates the channel setting for the DIR-825. By default the channel is set to 6. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto.Channel.Scan, this option will be greyed out.
Transmission Rate:
Select the transmit rate. It is strongly suggested to select Best.(Auto) for best performance.
D-Link DIR-825 User Manual 36
Section 3 - Configuration
Channel Width:
Select the Channel Width:
Auto.20/40 - This is the default setting. Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Visibility Status:
Select Invisible if you do not want the SSID of your wireless network to be broadcasted by the DIR-825. If Invisible is selected, the
SSID of the DIR-825 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DIR-825 in order to connect to it.
Wireless Security:
Refer to page 38 for more information regarding wireless security.
D-Link DIR-825 User Manual 37
Section 4 - Security
Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The DIR-825 offers the following types of security:
• WPA2 (Wi-Fi Protected Access 2)
• WPA (Wi-Fi Protected Access)
• WPA2-PSK (Pre-Shared Key)
• WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network.
D-Link DIR-825 User Manual 38
Section 4 - Security
Wireless Security Setup Wizard
To run the security wizard, click on Setup at the top and then click
Wireless.Network.Setup.Wizard.
Check the Manually.set.5GHz.band.Network.Name... box to manually set your desired wireless network name for the 5GHz band.
Type your desired wireless network name (SSID).
Automatically:.Select this option to automatically generate the router’s network key and click Next.
Manually: Select this option to manually enter your network key and click Next.
D-Link DIR-825 User Manual 39
Section 4 - Security
If you selected Automatically, the summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings.
If you selected Manually, the following screen will appear.
D-Link DIR-825 User Manual 40
Section 4 - Security
Add Wireless Device with WPS Wizard
From the Setup > Wireless.Settings screen, click Add.Wireless.
Device.with.WPS.
Select Auto to add a wireless client using WPS (Wi-Fi Protected
Setup) and then click Next. Skip to the next page.
If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients. Click
OK to finish.
D-Link DIR-825 User Manual 41
Section 4 - Security
PIN: Select this option to use PIN method. In order to use this method you must know the wireless client’s 8 digit PIN and click
Connect.
PBC:.Select this option to use PBC (Push Button) method to add a wireless client. Click Connect.
Once you click.Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection.
D-Link DIR-825 User Manual 42
Section 4 - Security
WPA/WPA2-Personal (PSK)
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on.Setup.and then click.Wireless.Settings on the left side.
2. Next to Security Mode, select WPA-Personal.
3. Next to WPA Mode, select Auto, WPA2.Only, or.WPA.Only. Use Auto if you have wireless clients using both WPA and WPA2.
4. Next to Cypher Type, select TKIP.and.AES, TKIP, or AES.
5. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed (3600 is default).
6. Next to Pre-Shared Key, enter a key (passphrase). The key is entered as a pass-phrase in ASCII format at both ends of the wireless connection.
The pass-phrase must be between 8-63 characters.
7. Click Save.Settings to save your settings. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on the router.
D-Link DIR-825 User Manual 43
Section 4 - Security
Configure WPA/WPA2-Enterprise (RADIUS)
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead.
1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). Click on.Setup. and then click.Wireless.Settings on the left side.
2. Next to Security Mode, select WPA-Enterprise.
3. Next to WPA Mode, select Auto, WPA2.Only, or.WPA.Only. Use Auto if you have wireless clients using both WPA and WPA2.
4. Next to Cypher Type, select TKIP.and.AES, TKIP, or AES.
5. Next to Group Key Update Interval, enter the amount of time before the group key used for broadcast and multicast data is changed
(3600 is default).
6. Next to Authentication Timeout, enter the amount of time before a client is required to re-authenticate (60 minutes is default).
7. Next to RADIUS Server IP Address enter the IP Address of your RADIUS server.
D-Link DIR-825 User Manual 44
Section 4 - Security
8. Next to RADIUS Server Port, enter the port you are using with your RADIUS server. 1812 is the default port.
9. Next to RADIUS Server Shared Secret, enter the security key.
10. If the MAC Address Authentication box is selected then the user will need to connect from the same computer whenever logging into the wireless network.
11. Click Advanced to enter settings for a secondary RADIUS Server.
12. Click Apply.Settings to save your settings.
D-Link DIR-825 User Manual 45
Section 3 - Configuration
Network Settings
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Router Settings
Router IP Address:
Enter the IP address of the router. The default IP address is 192.168.0.1.
If you change the IP address, once you click Save.Settings, you will need to enter the new IP address in your browser to get back into the configuration utility.
Subnet Mask:
Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
Device Name:
Enter a name for the router.
Local Domain:
Enter the Domain name (Optional).
Enable DNS Relay:
Uncheck the box to transfer the DNS server information from your ISP to your computers. If checked, your computers will use the router for a DNS server.
D-Link DIR-825 User Manual 46
Section 3 - Configuration
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-825 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-825. The DHCP Server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
Enable DHCP
Server:
Check this box to enable the DHCP server on your router.
Uncheck to disable this function.
DHCP IP Address
Range:
Enter the starting and ending IP addresses for the DHCP server’s
IP assignment.
Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict.
DHCP Lease Time:
The length of time for the IP address lease. Enter the Lease time in minutes.
Always
Broadcast:
Enable this feature to broadcast your networks DHCP server to
LAN/WLAN clients.
NetBIOS
Announcement:
NetBIOS allows LAN hosts to discover all other computers within the network, enable this feature to allow the DHCP Server to offer NetBIOS configuration settings.
Learn NetBIOS from WAN:
Enable this feature to allow WINS information to be learned from the WAN side, disable to allow manual configuration.
NetBIOS Scope:
This feature allows the configuration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no effect if the ‘Learn NetBIOS information from WAN’ is activated.
D-Link DIR-825 User Manual 47
Section 3 - Configuration
NetBIOS Node:
Select the different type of NetBIOS node;
Broadcast.only, Point-to-Point, Mixed-mode, and Hybrid.
WINS IP
Address:
Enter your WINS Server IP address(es).
D-Link DIR-825 User Manual 48
Section 3 - Configuration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
Enable:
Check this box to enable the reservation.
Computer Name:
Enter the computer name or select from the drop-down menu and click <<.
IP Address:
Enter the IP address you want to assign to the computer or device. This IP Address must be within the DHCP IP
Address Range.
MAC Address:
Enter the MAC address of the computer or device.
Copy Your PC’s
MAC Address:
If you want to assign an IP address to the computer you are currently on, click this button to populate the fields.
Save:
Click Save to save your entry. You must click Save.Settings at the top to activate your reservations.
DHCP Reservations List
DHCP
Reservations List:
Displays any reservation entries. Displays the host name
(name of your computer or device), MAC Address, and IP address.
Enable:
Check to enable the reservation.
Edit:
Click the edit icon to make changes to the reservation entry.
Delete:
Click to remove the reservation from the list.
D-Link DIR-825 User Manual 49
Section 3 - Configuration
Media Server
This feature allows you to share music, pictures and videos with any devices connected to your network.
Enable Media
Server:
Check this box to enable the media server feature.
Computer
Name:
Enter the media server’s name.
D-Link DIR-825 User Manual 50
Section 3 - Configuration
Storage
This page will allow you to access files from a USB external hard drive or thumb drive that is plugged into the router from your local network or from the Internet using either a web browser or an app for your smartphone or tablet. You can create users to be allowed to access these files.
Enable Web File
Access:
Check to enable sharing files on your USB storage device that is plugged in your router.
Enable HTTP
Storage Remote
Access:
Check to enable HTTP access to your router’s storage. You will have to type HTTP in the URL.
Remote Access
Port:
Enter a port (8181 is default). You will have to enter this port in the URL when connecting to the shared files. For example:
(http://192.168.0.1:8181).
Enable HTTPS
Storage Remote
Access:
Check to enable HTTPS (secure) access to your router’s storage. You will have to type HTTPS in the URL.
Remote HTTPS
Port:
Enter a port (4433 is default). You will have to enter this port in the URL when connecting to the shared files. For example:
(https://192.168.0.1:8181).
User Name:
To create a new user, enter a user name.
Password:
Enter a password for this account.
Verify Password:
Re-enter the password. Click Add/Edit to create the user.
User List:
Displays the accounts. The Admin and Guest accounts are built-in to the router.
Number of
Devices:
Displays the USB device plugged into the router.
D-Link DIR-825 User Manual 51
Section 3 - Configuration
IPv6
On this page, the user can configure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually configure the connection.
For the beginner user that has not configured a router before, click on the
IPv6.Internet.Connection.Setup.Wizard.button and the router will guide you through a few simple steps to get your network up and running.
For the advanced user that has configured a router before, click on the
Manual.IPv6.Internet.Connection.Setup button to input all the settings manually.
To configure the IPv6 local settings, click on the
IPv6.Local.Connectivity.
Setup button.
D-Link DIR-825 User Manual 52
Section 3 - Configuration
IPv6 Internet Connection Setup Wizard
On this page, the user can configure the IPv6 Connection type using the IPv6 Internet Connection Setup Wizard.
Click the IPv6.Internet.Connection.Setup.Wizard button and the router will guide you through a few simple steps to get your network up and running.
Click Next to continue to the next page. Click Cancel to discard the changes made and return to the main page.
The router will try to detect whether its possible to obtain the IPv6 Internet connection type automatically. If this succeeds then the user will be guided through the input of the appropriate parameters for the connection type found.
D-Link DIR-825 User Manual 53
Section 3 - Configuration
However, if the automatic detection fails, the user will be prompt to either Try.
again.or to click on the Guide.me.through.the.IPv6.settings button to initiate the manual continual of the wizard.
There are several connection types to choose from. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled. The 3 options available on this page are.IPv6.over.PPPoE,.Static.IPv6.address.and.Route, and Tunneling.
Connection.
Choose the required IPv6 Internet Connection type and click on the Next button to continue. Click on the Prev button to return to the previous page. Click on the
Cancel button to discard all the changes made and return to the main page.
Click on the Next button to continue. Click on the Prev button to return to the previous page.
Click on the Cancel button to discard all the changes made and return to the main page.
D-Link DIR-825 User Manual 54
Section 3 - Configuration
IPv6.over.PPPoE
After selecting the IPv6 over PPPoE option, the user will be able to configure the
IPv6 Internet connection that requires a username and password to get online.
Most DSL modems use this type of connection.
The following parameters will be available for configuration:
PPPoE.Session: Select the PPPoE Session value used here. This option will state that this connection shares it’s information with the already configured IPv6
PPPoE connection, or the user can create a new
PPPoE connection here.
User.Name: Enter the PPPoE username used here. If you do not know your user name, please contact your ISP.
Password: Enter the PPPoE password used here. If you do not know your password, please contact your ISP.
Verify.Password: Re-enter the PPPoE password used here.
Service.Name: Enter the service name for this connection here.
This option is optional.
D-Link DIR-825 User Manual 55
Section 3 - Configuration
Static.IPv6.Address.Connection
This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your
IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS
Server. Your ISP provides you with all this information.
Use.Link-Local.
Address:
The Link-local address is used by nodes and routers when communicating with neighboring nodes on the same link.
This mode enables IPv6-capable devices to communicate with each other on the LAN side.
IPv6.Address:
Enter the WAN IPv6 address for the router here.
Subnet.Prefix.
Length:
Enter the WAN subnet prefix length value used here.
Default.Gateway:
Enter the WAN default gateway IPv6 address used here.
Primary.IPv6.DNS.
Address:
Enter the WAN primary DNS Server address used here.
Secondary.IPv6.
DNS.Address:
Enter the WAN secondary DNS Server address used here.
LAN.IPv6.Address:
These are the settings of the LAN (Local Area Network)
IPv6 interface for the router. The router’s LAN IPv6 Address configuration is based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with prefix /64 is supported in LAN.)
D-Link DIR-825 User Manual 56
Section 3 - Configuration
Tunneling.Connection.(6rd)
After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings.
The following parameters will be available for configuration:
6rd IPv6 Prefix: Enter the 6rd IPv6 address and prefix value used here.
IPv4 Address: Enter the IPv4 address used here.
Mask Length: Enter the IPv4 mask length used here.
Assigned IPv6 Prefix: Displays the IPv6 assigned prefix value here.
6rd Border Relay IPv4
Address:
Enter the 6rd border relay IPv4 address used here.
IPv6 DNS Server: Enter the primary DNS Server address used here.
The IPv6 Internet Connection Setup Wizard is complete.
Click on the Connect button to continue. Click on the Prev button to return to the previous page. Click on the Cancel button to discard all the changes made and return to the main page.
D-Link DIR-825 User Manual 57
Section 3 - Configuration
IPv6 Manual Setup
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE,
IPv6 in IPv4 Tunnel, 6to4, 6rd, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet
Service Provider.
Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled.
Auto Detection
Select Auto.Detection to have the router detect and automatically configure your IPv6 setting from your ISP.
D-Link DIR-825 User Manual 58
Section 3 - Configuration
Static IPv6
My IPv6 Connection:
Select Static.IPv6 from the drop-down menu.
WAN IPv6 Address
Settings:
Enter the address settings supplied by your Internet provider
(ISP).
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local Address:
Displays the Router’s LAN Link-Local Address.
Enable
Autoconfiguration:
Check to enable the Autoconfiguration feature.
Autoconfiguration Type:
Select Stateful.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.
Stateless.DHCPv6.
IPv6 Address Range
Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Range
End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Lifetime:
Enter the IPv6 Address Lifetime (in minutes).
D-Link DIR-825 User Manual 59
Section 3 - Configuration
Autoconfiguration
My IPv6 Connection:
Select Autoconfiguration.(Stateless/DHCPv6) from the drop-down menu.
IPv6 DNS Settings:
Select either Obtain.DNS.server.address.automatically or
Use.the.following.DNS.Address.
Primary/Secondary DNS
Address:
Enter the primary and secondary DNS server addresses.
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local Address:
Displays the Router’s LAN Link-Local Address.
Enable
Autoconfiguration:
Check to enable the Autoconfiguration feature.
Autoconfiguration Type:
Select
Stateful.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.
Stateless.DHCPv6.
IPv6 Address Range
Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Range
End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Lifetime:
Enter the IPv6 Address Lifetime (in minutes).
D-Link DIR-825 User Manual 60
Section 3 - Configuration
PPPoE
My IPv6 Connection:
Select PPPoE from the drop-down menu.
PPPoE:
Enter the PPPoE account settings supplied by your Internet provider (ISP).
Address Mode:
Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic.
IP Address:
Enter the IP address (Static PPPoE only).
User Name:
Enter your PPPoE user name.
Password:
Enter your PPPoE password and then retype the password in the next box.
Service Name:
Enter the ISP Service Name (optional).
Reconnection Mode:
Select either Always-on, On-Demand, or Manual.
Maximum Idle Time:
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
MTU:
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU.
IPv6 DNS Settings:
Select either Obtain.DNS.server.address.automatically or Use.
the.following.DNS.Address.
Primary/Secondary DNS
Address:
Enter the primary and secondary DNS server addresses.
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local Address:
Displays the Router’s LAN Link-Local Address.
Enable Autoconfiguration:
Check to enable the Autoconfiguration feature.
D-Link DIR-825 User Manual 61
Section 3 - Configuration
Autoconfiguration Type:
Select
Stateful.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.Stateless.DHCPv6.
IPv6 Address Range Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Range End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Lifetime:
Enter the IPv6 Address Lifetime (in minutes).
D-Link DIR-825 User Manual 62
Section 3 - Configuration
IPv6 in IPv4 Tunneling
My IPv6
Connection:
Select IPv6.in.IPv4.Tunnel from the drop-down menu.
IPv6 in IPv4 Tunnel
Settings:
Enter the settings supplied by your Internet provider (ISP).
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local
Address:
Displays the Router’s LAN Link-Local Address.
Enable
Autoconfiguration:
Check to enable the Autoconfiguration feature.
Autoconfiguration
Type:
Select Stateful.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.Stateless.
DHCPv6.
IPv6 Address
Range Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address
Range End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
Pv6 Address
Lifetime:
Enter the Router Advertisement Lifetime (in minutes).
D-Link DIR-825 User Manual 63
Section 3 - Configuration
6 to 4 Tunneling
My IPv6 Connection:
Select 6.to.4 from the drop-down menu.
6 to 4 Settings:
Enter the IPv6 settings supplied by your Internet provider (ISP).
Primary/Secondary
DNS Address:
Enter the primary and secondary DNS server addresses.
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local
Address:
Displays the Router’s LAN Link-Local Address.
Enable
Autoconfiguration:
Check to enable the Autoconfiguration feature.
Autoconfiguration
Type:
Select Stateful.(DHCPv6), SLAAC.+.RDNSS or SLAAC.+.Stateless.
DHCPv6.
IPv6 Address Range
Start:
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address Range
End:
Enter the end IPv6 Address for the DHCPv6 range for your local computers.
IPv6 Address
Lifetime:
Enter the IPv6 Address Lifetime (in minutes).
D-Link DIR-825 User Manual 64
Section 3 - Configuration
6rd
My IPv6 Connection:
Select 6rd from the drop-down menu.
6RD Settings:
Enter the address settings supplied by your Internet provider
(ISP).
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN Link-Local Address:
Displays the Router’s LAN Link-Local Address.
Enable
Autoconfiguration:
Check to enable the Autoconfiguration feature.
Autoconfiguration Type:
Select Stateful (DHCPv6), SLAAC+RDNSS or SLAAC + Stateless
DHCPv6.
Router Advertisement
Lifetime:
Enter the Router Advertisement Lifetime (in minutes).
D-Link DIR-825 User Manual 65
Section 3 - Configuration
Link-Local Connectivity
My IPv6 Connection:
Select Link-Local.Only from the drop-down menu.
LAN IPv6 Address
Settings:
Displays the IPv6 address of the router.
D-Link DIR-825 User Manual 66
Section 3 - Configuration
Advanced
Virtual Server
This will allow you to open a single port. If you would like to open a range of ports, refer to the next page.
Name:
Enter a name for the rule or select an application from the drop-down menu. Select an application and click
<< to populate the fields.
IP Address:
Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<.
Private Port/
Public Port:
Enter the port that you want to open next to Private
Port and Public Port. The private and public ports are usually the same. The public port is the port seen from the Internet side, and the private port is the port being used by the application on the computer within your local network.
Protocol Type:
Select TCP, UDP, or Both.from the drop-down menu.
Schedule:
The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools
> Schedules section.
Inbound Filter:
Select Allow.All (most common) or a created Inbound filter. You may create your own inbound filters in the
Advanced.>.Inbound.Filter page.
D-Link DIR-825 User Manual 67
Section 3 - Configuration
Port Forwarding
This will allow you to open a single port or a range of ports.
Name:
Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields.
IP Address:
Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP), you computer will be listed in the “Computer Name” drop-down menu. Select your computer and click <<.
TCP/UDP:
Enter the TCP and/or UDP port or ports that you want to open. You can enter a single port or a range of ports. Separate ports with a common.
Example: 24,1009,3000-4000
Schedule:
The schedule of time when the Virtual Server Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools
> Schedules section.
Inbound Filter:
Select Allow. All (most common) or a created
Inbound filter. You may create your own inbound filters in the Advanced.>.Inbound.Filter page.
D-Link DIR-825 User Manual 68
Section 3 - Configuration
Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others.
These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-825. If you need to run applications that require multiple connections, specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or UDP, then enter the firewall
(public) ports associated with the trigger port to open them for inbound traffic.
The DIR-825 provides some predefined applications in the table on the bottom of the web page. Select the application you want to use and enable it.
Name:
Enter a name for the rule. You may select a pre-defined application from the drop-down menu and click <<.
Trigger:
This is the port used to trigger the application. It can be either a single port or a range of ports.
Traffic Type:
Select the protocol of the trigger port (TCP, UDP, or Both).
Firewall:
This is the port number on the Internet side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges.
Traffic Type:
Select the protocol of the firewall port (TCP, UDP, or Both).
Schedule:
The schedule of time when the Application Rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the
Tools > Schedules section.
D-Link DIR-825 User Manual 69
Section 3 - Configuration
QoS Engine
The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically.
Enable Traffic
Shaping:
This option is disabled by default. Enable this option for better performance and experience with online games and other interactive applications, such as VoIP.
Automatic Uplink
Speed:
This option is enabled by default when the QoS Engine option is enabled. This option will allow your router to automatically determine the uplink speed of your Internet connection.
Measured Uplink
Speed:
This displays the detected uplink speed.
Manual Uplink
Speed:
The speed at which data can be transferred from the router to your ISP. This is determined by your ISP. ISP’s often speed as a download/upload pair. For example,
1.5Mbits/284Kbits. Using this example, you would enter
284. Alternatively you can test your uplink speed with a service such as speedtest.net.
Enable QoS
Engine:
This option is enabled by default. This will allow your router to automatically determine the network priority of running programs.
Automatic
Classification:
This option should be enabled when you have a slow Internet uplink. It helps to reduce the impact that large low priority network packets can have on more urgent ones.
Dynamic
Fragmentation:
This option should be enabled when you have a slow Internet uplink. It helps to reduce the impact that large low priority network packets can have on more urgent ones.
D-Link DIR-825 User Manual 70
Section 3 - Configuration
Network Filters
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
Configure MAC
Filtering:
Select. Turn. MAC. Filtering. Off, Allow. MAC.
addresses.listed.below, or Deny.MAC.addresses.
listed.below from the drop-down menu.
MAC Address:
Enter the MAC address you would like to filter.
To find the MAC address on a computer, please refer to the Networking Basics section in this manual.
DHCP Client:
Select a DHCP client from the drop-down menu and click << to copy that MAC Address.
Clear:
Click to remove the MAC address.
D-Link DIR-825 User Manual 71
Section 3 - Configuration
Access Control
The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.
Add Policy:
Click the Add.Policy button to start the Access
Control Wizard.
Click Next to continue with the wizard.
Access Control Wizard
D-Link DIR-825 User Manual 72
Section 3 - Configuration
Enter a name for the policy and then click Next to continue.
Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue.
Enter the following information and then click Next to continue.
• Address.Type - Select IP address, MAC address, or Other
Machines.
• IP.Address - Enter the IP address of the computer you want to apply the rule to.
• Machine.Address - Enter the PC MAC address (i.e. 00:00.00.00.00).
Select the filtering method and then click Next to continue.
D-Link DIR-825 User Manual 73
Section 3 - Configuration
Enter the rule:
Enable - Check to enable the rule.
Name - Enter a name for your rule.
Dest.IP.Start - Enter the starting IP address.
Dest.IP.End - Enter the ending IP address.
Protocol - Select the protocol.
Dest.Port.Start - Enter the starting port number.
Dest.Port.End - Enter the ending port number.
To enable web logging, click Enable.
Click Save to save the access control rule.
Your newly created policy will now show up under Policy.Table.
D-Link DIR-825 User Manual 74
Section 3 - Configuration
Website Filters
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network.
To use this feature select to Allow or Deny, enter the domain or website and click Save.Settings. You must also select Apply.
Web.Filter under the Access Control section (page 42).
Add Website
Filtering Rule:
Select either DENY.computers.access.to.ONLY.
these.sites or ALLOW.computers.access.to.ONLY.
these.sites.
Website URL/
Domain:
Enter the keywords or URLs that you want to allow or block. Click Save.Settings.
D-Link DIR-825 User Manual 75
Section 3 - Configuration
Inbound Filters
The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual
Server, Port Forwarding, or Remote Administration features.
Name:
Enter a name for the inbound filter rule.
Action:
Select Allow or Deny.
Enable:
Check to enable rule.
Remote IP Start:
Enter the starting IP address. Enter 0.0.0.0 if you do not want to specify an IP range.
Remote IP End:
Enter the ending IP address. Enter 255.255.255.255 if you do not want to specify and IP range.
Add:
Click the Add button to apply your settings. You must click Save.Settings at the top to save the settings.
Inbound Filter
Rules List:
This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule.
D-Link DIR-825 User Manual 76
Section 3 - Configuration
Firewall Settings
A firewall protects your network from the outside world. The DIR-825 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications.
If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Enable SPI:
SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol.
Anti-Spoof Check:
Enable this feature to protect your network from certain kinds of
“spoofing” attacks.
Enable DMZ:
If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer.
Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.
DMZ IP Address:
Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication. If this computer obtains it’s IP address automatically using DHCP, be sure to make a static reservation on the Setup >
Network.Settings page so that the IP address of the
DMZ machine does not change.
PPTP:
Allows multiple machines on the LAN to connect to their corporate network using PPTP protocol.
IPSEC (VPN):
Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec through
NAT. This ALG may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG off. Please check with the system administrator of your corporate network whether your VPN client supports
NAT traversal.
D-Link DIR-825 User Manual 77
Section 3 - Configuration
RTSP:
Allows application that uses Real Time Streaming Protocol to receive streaming media from the Internet. QuickTime and Real Player are some of the common applications using this protocol.
SIP:
Allows devices and applications using VoIP (Voice over IP) to communicate across NAT. Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG off.
D-Link DIR-825 User Manual 78
Section 3 - Configuration
Routing
The Routing option is an advanced method of customizing specific routes of data through your network.
Destination IP:
Enter the IP address of packets that will take this route.
Netmask:
Enter the netmask of the route, please note that the octets must match your destination IP address.
Gateway:
Enter your next hop gateway to be taken if this route is used.
Metric:
The route metric is a value from 1 to 16 that indicates the cost of using this route. A value 1 is the lowest cost and 15 is the highest cost.
Interface:
Select the interface that the IP packet must use to transit out of the router when this route is used.
D-Link DIR-825 User Manual 79
Section 3 - Configuration
Advanced Wireless
Transmit Power:
Set the transmit power of the antennas.
WLAN Partition:
This enables 802.11d operation. 802.11d is a wireless specification developed to allow implementation of wireless networks in countries that cannot use the
802.11 standard. This feature should only be enabled if you are in a country that requires it.
WMM Enable:
WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients.
Short GI:
Check this box to reduce the guard interval time therefore increasing the data capacity. However, it’s less reliable and may create higher data loss.
HT20/40 Coexistence
(2.4GHz only):
Select to Enable or Disable this feature.
D-Link DIR-825 User Manual 80
Section 3 - Configuration
Wi-Fi Protected Setup (WPS)
Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures.
The process is just as easy as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin
Code Method. The time reduction in setup and ease of use are quite beneficial, while the highest wireless Security setting of
WPA2 is automatically used.
Enable:
Enable the Wi-Fi Protected Setup feature.
Note: if this option is unchecked, the WPS button on the side of the router will be disabled.
Lock Wireless
Security
Settings:
Locking the wireless security settings prevents the settings from being changed by the Wi-Fi Protected
Setup feature of the router. Devices can still be added to the network using Wi-Fi Protected Setup. However, the settings of the network will not change once this option is checked.
PIN Settings:
A PIN is a unique number that can be used to add the router to an existing network or to create a new network. Only the Administrator (“admin” account) can change or reset the PIN.
Current PIN:
Shows the current PIN.
Reset PIN to
Default:
Restore the default PIN of the router.
Generate New
PIN:
Create a random number that is a valid PIN. This becomes the router’s PIN. You can then copy this PIN to the user interface of the wireless client.
D-Link DIR-825 User Manual 81
Section 3 - Configuration
Add Wireless
Station:
This Wizard helps you add wireless devices to the wireless network.
The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the
PIN for the device, or ask you to press the configuration button on the device. If the device supports Wi-Fi Protected Setup and has a configuration button, you can add it to the network by pressing the configuration button on the device and then the on the router within 60 seconds. The status LED on the router will flash three times if the device has been successfully added to the network.
There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the device. The router acts as a registrar for the network, although other devices may act as a registrar as well.
Add Wireless
Device Wizard:
Click to start the wizard and skip to page 41.
WPS Button
You can also simply press the WPS button on the side of the router, and then press the WPS button on your wireless client to automatically connect without logging into the router.
Refer to page 106 for more information.
D-Link DIR-825 User Manual 82
Section 3 - Configuration
Advanced Network Settings
Enable UPnP:
To use the Universal Plug and Play (UPnP
™
) feature click on
Enabled. UPnP provides compatibility with networking equipment, software and peripherals.
WAN Ping:
Checking the box will allow the DIR-825 to respond to pings. Unchecking the box may provide some extra security from hackers.
WAN Ping Inbound
Filter:
Select from the drop-down menu if you would like to apply the Inbound Filter to the WAN ping. Refer to the Inbound
Filters section for more information.
WAN Port Speed:
You may set the port speed of the Internet port to 10Mbps,
100Mbps, 1000Mbps, or Auto (recommended).
Enable IPV4
Multicast Streams:
Check the box to allow multicast traffic to pass through the router from the Internet (IPv4).
Enable IPV6
Multicast Streams:
Check the box to allow multicast traffic to pass through the router from the Internet (IPv6).
D-Link DIR-825 User Manual 83
Section 3 - Configuration
Guest Zone
The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network. You may configure different zones for the 2.4GHz and 5GHz wireless bands.
Enable Guest
Zone:
Check to enable the Guest Zone feature.
Schedule:
The schedule of time when the Guest Zone will be active. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Tools > Schedules section.
Wireless
Network Name:
Enter a wireless network name (SSID) that is different from your main wireless network.
Enable Routing
Between Zones:
Check to allow network connectivity between the different zones created.
Security Mode:
Select the type of security or encryption you would like to enable for the guest zone.
D-Link DIR-825 User Manual 84
Section 3 - Configuration
IPv6 Firewall
The DIR-825’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device. The
DIR-825’s IPv6 Firewall functions in a similar way to the IP Filters feature.
Enable Checkbox:
Check the box to enable the IPv6 firewall simple security.
Configure IPv6
Firewall:
Select an action from the drop-down menu.
Name:
Enter a name to identify the IPv6 firewall rule.
Schedule:
Use the drop-down menu to select the time schedule that the IPv6 Firewall Rule will be enabled on. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the
Tools > Schedules section.
Source:
Use the Source drop-down menu to specify the interface that connects to the source IPv6 addresses of the firewall rule.
IP Address Range:
Enter the source IPv6 address range in the adjacent IP
Address Range field.
Dest:
Use the Dest drop-down menu to specify the interface that connects to the destination IP addresses of the firewall rule.
Protocol:
Select the protocol of the firewall port (All, TCP, UDP, or ICMP).
Port Range:
Enter the first port of the range that will be used for the firewall rule in the first box and enter the last port in the field in the second box.
D-Link DIR-825 User Manual 85
Section 3 - Configuration
IPv6 Routing
This page allows you to specify custom routes that determine how data is moved around your network.
Route List:
Check the box next to the route you wish to enable.
Name:
Enter a specific name to identify this route.
Destination IP/
Prefix Length:
This is the IP address of the router used to reach the specified destination or enter the IPv6 address prefix length of the packets that will take this route.
Metric:
Enter the metric value for this rule here.
Interface:
Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router.
Gateway:
Enter the next hop that will be taken if this route is used.
D-Link DIR-825 User Manual 86
Section 3 - Configuration
Tools
Admin
This page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
Admin Password:
Enter a new password for the Administrator Login Name. The administrator can make changes to the settings.
User Password:
Enter the new password for the User login. If you login as the User, you cannot change the settings (you can only view them).
System Name:
Enter a name for your router.
Enable Graphical
Authentication:
Enables a challenge-response test to require users to type letters or numbers from a distorted image displayed on the screen to prevent online hackers and unauthorized users from gaining access to your router’s network settings.
Enable HTTPS
Server:
Check to enable HTTPS to connect to the router securely. This means to connect to the router, you must enter https://192.168.0.1 (for example) instead of
http://192.168.0.1.
Enable Remote
Management:
Remote management allows the DIR-825 to be configured from the Internet by a web browser. A username/password is still required to access the Web
Management interface.
Remote Admin Port:
The port number used to access the DIR-825 is used in the URL. Example:
http://x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-825 and 8080 is the port used for the Web Management interface.
If you have enabled HTTPS.Server, you must enter https:// as part of the URL to access the router remotely.
Remote Admin
Inbound Filter:
This section will list any rules that are created. You may click the Edit icon to change the settings or enable/disable the rule, or click the Delete icon to remove the rule. Details will display the current status.
D-Link DIR-825 User Manual 87
Section 3 - Configuration
Time
The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed.
Time:
Displays the current date and time of the router.
Time Zone:
Select your Time Zone from the drop-down menu.
Enable Daylight
Saving:
To select Daylight Saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time.
Enable NTP Server:
NTP is short for Network Time Protocol. A NTP server will synch the time and date with your router. This will only connect to a server on the
Internet, not a local server. Check the box to enable this feature.
NTP Server Used:
Enter the IP address of a NTP server or select one from the drop-down menu.
Manual:
To manually input the time, enter the values in these fields for the Year, Month, Day, Hour,
Minute, and Second and then click
Set.Time.
You can also click Copy.Your.Computer’s.Time.
Settings to synch the date and time with the computer you are currently on.
D-Link DIR-825 User Manual 88
Section 3 - Configuration
SysLog
The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a
SysLog server on your network.
Enable Logging to
SysLog Server:
Check this box to send the router logs to a SysLog
Server.
SysLog Server IP
Address:
The address of the SysLog server that will be used to send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
D-Link DIR-825 User Manual 89
Section 3 - Configuration
Email Settings
The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your email address.
Enable Email
Notification:
When this option is enabled, router activity logs are emailed to a designated email address.
From Email
Address:
This email address will appear as the sender when you receive a log file or firmware upgrade notification via email.
To Email Address:
Enter the email address where you want the email sent.
SMTP Server
Address:
Enter the SMTP server address for sending email.
SMTP Server Port:
Enter the SMTP port used on the server.
Enable
Authentication:
Check this box if your SMTP server requires authentication.
Account Name:
Enter your account for sending email.
Password:
Enter the password associated with the account.
Re-type the password associated with the account.
On Log Full:
When this option is selected, logs will be sent via email to your account when the log is full.
On Schedule:
Selecting this option will send the logs via email according to schedule.
Schedule:
This option is enabled when
On.Schedule is selected. You can select a schedule from the list of defined schedules. To create a schedule, go to Tools.>.Schedules.
D-Link DIR-825 User Manual 90
Section 3 - Configuration
System
This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
Save Settings to
Local Hard Drive:
Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. A file dialog will appear, allowing you to select a location and file name for the settings.
Load Settings from Local Hard
Drive:
Use this option to load previously saved router configuration settings. First, use the Browse option to find a previously saved file of configuration settings. Then, click the Load button to transfer those settings to the router.
Restore to
Factory Default
Settings:
This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory.
Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save button above.
Reboot Device:
Click to reboot the router.
D-Link DIR-825 User Manual 91
Section 3 - Configuration
Firmware
You can upgrade the firmware of the access point here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from this site.
Browse:
After you have downloaded the new firmware, click
Browse to locate the firmware update on your hard drive. Click Upload to complete the firmware upgrade.
Upload:
Once you have a firmware update on your computer, use this option to browse for the file and then upload the information into the access point.
Language Pack
You can change the language of the web UI by uploading available language packs.
Browse:
After you have downloaded the new language pack, click Browse to locate the language pack file on your hard drive. Click Upload to complete the language pack upgrade.
D-Link DIR-825 User Manual 92
Section 3 - Configuration
Dynamic DNS
The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Enable
Dynamic DNS:
Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP
Address. Check the box to enable DDNS.
Server
Address:
Select your DDNS provider from the drop-down menu or enter the DDNS server address.
Host Name:
Enter the Host Name that you registered with your DDNS service provider.
Username or
Key:
Enter the Username or key for your DDNS account.
Password or
Key:
Enter the Password or key for your DDNS account.
Timeout:
Enter a timeout time (in hours).
Status:
Displays the current connection status.
DDNS.for.IPv6.Hosts
Enable:
Check the box to enable DDNS for IPv6 Hosts.
IPv6
Address:
Enter the IPv6 address of your computer/server in your local network. You can click the << button and select a computer/server from the drop-down list.
D-Link DIR-825 User Manual 93
Section 3 - Configuration
Host Name:
Enter the IPv6 Host Name that you registered with your DDNS service provider.
IPv6 DDNS
List:
Once you save your entry, the IPv6 DDNS host information will be displayed here.
Enable:
Check to enable the entry.
Host Name:
Displays the name of your IPv6 DDNS host.
IPv6 Address:
Displays the IPv6 address of your computer/server associated with the IPv6 DDNS host.
Edit/Delete:
Click the edit icon to make changes to the entry or click the delete icon to remove the entry.
D-Link DIR-825 User Manual 94
Section 3 - Configuration
System Check
Ping Test:
The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP address that you wish to Ping and click Ping.
IPv6 Ping Test:
Enter the IPv6 address that you wish to Ping and click Ping.
Ping Results:
The results of your ping attempts will be displayed here.
D-Link DIR-825 User Manual 95
Section 3 - Configuration
Schedules
Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to
8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm.
Name:
Enter a name for your new schedule.
Days:
Select a day, a range of days, or All Week to include every day.
Time:
Check All.Day.-.24hrs or enter a start and end time for your schedule.
Save:
You must click Save.Settings at the top for your schedules to go into effect.
Schedule Rules
List:
The list of schedules will be listed here. Click the
Edit icon to make changes or click the Delete icon to remove the schedule.
D-Link DIR-825 User Manual 96
Section 3 - Configuration
Status
Device Info
This page displays the current information for the DIR-825. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use
Release to disconnect from your ISP and use Renew to connect to your ISP.
If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use
Connect to establish the PPPoE connection.
General:
Displays the router’s time and firmware version.
WAN:
Displays the MAC address and the public IP settings
LAN:
Displays the MAC address and the private (local) IP settings for the router.
Wireless LAN:
Displays the wireless MAC address and your wireless settings such as SSID and Channel. The first Wireless LAN section is for the 2.4GHz segment and the second section is for the 5GHz segment.
LAN Computers:
Displays computers and devices that are connected to the router via Ethernet and that are receiving an IP address assigned by the router (DHCP).
D-Link DIR-825 User Manual 97
Section 3 - Configuration
Logs
The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view. This router also has external Syslog Server support so you can send the log files to a computer on your network that is running a Syslog utility.
Log Types:
You can select the types of messages that you want to display from the log. System Activity, Debug
Information, Attacks, Dropped Packets, and Notice messages can be selected. Click Apply.Log.Settings.
Now to activate your settings.
Refresh:
Updates the log details on the screen so it displays any recent activity.
Clear:
Clears all of the log contents.
Email Now:
This option will send a copy of the router log to your email address configured in the Tools >
Email.Settings.
screen.
Save Log:
This option will save the router log to a file on your computer.
D-Link DIR-825 User Manual 98
Section 3 - Configuration
Statistics
The screen below displays the Traffic.Statistics. Here you can view the amount of packets that pass through the DIR-825 on both the WAN, LAN ports and both the 802.11n/g (2.4GHz) and 802.11n/a (5GHz) wireless bands. The traffic counter will reset if the device is rebooted.
D-Link DIR-825 User Manual 99
Section 3 - Configuration
Internet Sessions
The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
D-Link DIR-825 User Manual 100
Section 3 - Configuration
This page will display your current routing table.
Routing
D-Link DIR-825 User Manual 101
Section 3 - Configuration
Wireless
The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and
MAC address of the connected wireless clients.
D-Link DIR-825 User Manual 102
Section 3 - Configuration
IPv6
The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
D-Link DIR-825 User Manual 103
Section 3 - Configuration
IPV6 Routing
This page displays the IPV6 routing details configured for your router.
D-Link DIR-825 User Manual 104
Section 3 - Configuration
Support
D-Link DIR-825 User Manual 105
Section 4 - Security
Connect a Wireless Client to your Router
WPS Button
The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-825 router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step.1 - Press the WPS button on the DIR-825 for about 1 second. The WPS button will start to blink.
Step.2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).
Step.3 - Allow up to 1 minute to configure. Once the WPS light stops blinking, you will be connected and your wireless connection will be secure with WPA2.
D-Link DIR-825 User Manual 106
Section 4 - Security
Windows® 7
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
Wireless Icon
2. The utility will display any available wireless networks in your area.
D-Link DIR-825 User Manual 107
Section 4 - Security
3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
4. The following window appears while your computer tries to connect to the router.
D-Link DIR-825 User Manual 108
Section 4 - Security
5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router.
It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
D-Link DIR-825 User Manual 109
Section 4 - Security
WPS
The WPS feature of the DIR-825 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature:
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.
D-Link DIR-825 User Manual 110
Section 4 - Security
3. Double-click the DIR-825.
4. Input the WPS PIN number (displayed in the WPS window on the
Router’s LCD screen or in the Setup.> Wireless.Setup menu in the Router’s Web UI) and click Next.
D-Link DIR-825 User Manual 111
Section 4 - Security
5. Type a name to identify the network.
6. To configure advanced settings, click the icon.
Click Next to continue.
D-Link DIR-825 User Manual 112
Section 4 - Security
7. The following window appears while the Router is being configured.
Wait for the configuration to complete.
8. The following window informs you that WPS on the router has been setup successfully.
Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future.
9. Click Close to complete WPS setup.
D-Link DIR-825 User Manual 113
Section 5 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.
If you receive the Wireless.Networks.Detected bubble, click on the center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select
Connect.to.a.network.
The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking.Basics section in this manual for more information.
D-Link DIR-825 User Manual 114
Section 5 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1.. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect.to.a.network.
2.
. Highlight the wireless network (SSID) you would like to connect to and click Connect.
D-Link DIR-825 User Manual 115
Section 5 - Connecting to a Wireless Network
3. Enter the same security key or passphrase that is on your router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
D-Link DIR-825 User Manual 116
Section 5 - Connecting to a Wireless Network
WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software.
When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in support for WCN 2.0, use software provided by a third party, or manually configure.
If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the
Current PIN that is displayed on the Advanced > Wi-Fi.Protected.Setup section or choose to click the Generate.New.PIN button or Reset.PIN.to.Default button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed to the next section to set up the newly-configured router.
D-Link DIR-825 User Manual 117
Section 5 - Connecting to a Wireless Network
Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service
Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
If you receive the Wireless.Networks.Detected bubble, click on the center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select View.Available.Wireless.Networks.
The utility will display any available wireless networks in your area.
Click on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the Networking.
Basics section in this manual for more information.
D-Link DIR-825 User Manual 118
Section 5 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used.
1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View.Available.Wireless.Networks.
2. Highlight the wireless network (SSID) you would like to connect to and click Connect.
D-Link DIR-825 User Manual 119
Section 5 - Connecting to a Wireless Network
3. The Wireless.Network.Connection box will appear. Enter the WPA-PSK passphrase and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The
WPA-PSK passphrase must be exactly the same as on the wireless router.
D-Link DIR-825 User Manual 120
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-825. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.
1..Why.can’t.I.access.the.web-based.configuration.utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
- Microsoft Internet Explorer® 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google™ Chrome 2.0 and higher
- Apple Safari 3.0 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.
• Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate,
Norton Personal Firewall, and Windows
®
XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it.
D-Link DIR-825 User Manual 121
Section 6 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Settings > Control.Panel. Double-click the Internet.Options Icon. From the Security tab, click the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your web management.
• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2..What.can.I.do.if.I.forgot.my.password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.
D-Link DIR-825 User Manual 122
Section 6 - Troubleshooting
3..Why.can’t.I.connect.to.certain.sites.or.send.and.receive.emails.when.connecting.through.my.router?.
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and press
Enter.(or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
. ping.[url].[-f].[-l].[MTU.value]
Example: ping.yahoo.com.-f.-l.1472
D-Link DIR-825 User Manual 123
Section 6 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device.
• Click on Setup and then click Manual.Configure.
• To change the MTU enter the number in the MTU field and click Save.Settings to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten.
D-Link DIR-825 User Manual 124
Appendix A - Wireless Basics
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently.
Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide this link.
D-Link DIR-825 User Manual 125
Appendix A - Wireless Basics
What.is.Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network.
Why.D-Link.Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.
How.does.wireless.work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN), and Wireless Personal Area Network (WPAN).
Wireless.Local.Area.Network.(WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other outdoor venues.
D-Link DIR-825 User Manual 126
Appendix A - Wireless Basics
Wireless.Personal.Area.Network.(WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Who.uses.wireless?.
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business,
D-Link has a wireless solution for it.
Home
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small.Office.and.Home.Office
• Stay on top of everything at home as you would at office
• Remotely access your office network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate office space
D-Link DIR-825 User Manual 127
Appendix A - Wireless Basics
Where.is.wireless.used?.
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize.your.router.or.Access.Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate.Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/ access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency.
D-Link DIR-825 User Manual 128
Appendix A - Wireless Basics
Security
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.
Wireless Modes
There are basically two modes of networking:
• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-825 wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc mode to communicate.
D-Link DIR-825 User Manual 129
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the
Start.Search box.)
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router.
Some firewall software programs may block a DHCP request on newly installed adapters.
D-Link DIR-825 User Manual 130
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step.1
Windows® 7 - Click on Start > Control.Panel > Network.and.Internet > Network.and.Sharing.Center.
Windows Vista® - Click on Start > Control.Panel > Network.and.Internet > Network.and.Sharing.Center > Manage.Network
. .
.
Connections.
Windows® XP - Click on Start > Control.Panel > Network.Connections.
Windows® 2000 - From the desktop, right-click My.Network.Places > Properties.
Step.2
Right-click on the Local.Area.Connection which represents your network adapter and select Properties.
Step.3
Highlight Internet.Protocol.(TCP/IP) and click Properties.
Step.4
Click Use.the.following.IP.address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set the Default Gateway the same as the LAN IP address of your router (I.E. 192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step.5
Click OK twice to save your settings.
D-Link DIR-825 User Manual 131
.
Appendix C - Technical Specifications
Standards
• IEEE 802.11n
• IEEE 802.11g
• IEEE 802.11a
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.3ab
Technical Specifications
• 24Mbps • 18Mbps • 12Mbps
• 11Mbps • 9Mbps
• 5.5Mbps • 2Mbps
• 6Mbps
• 1Mbps
Frequency.Range
2
.(North.America)
• 2.412GHz to 2.462GHz (802.11g/n)
• 5.15GHz to 5.825GHz (802.11a/n)
3
.
.
Security
• WPA™ - Personal/Enterprise
• WPA2™ - Personal/Enterprise
Wireless.Signal.Rates
1
IEEE.802.11n.2.4GHz(HT20/40):
• 144.4Mbps (300) · 130Mbps (270)
• 115.6Mbps (240) · 86.7Mbps (180)
• 72.2Mbps (150) · 65Mbps (135)
• 57.8Mbps (120) · 43.3Mbps (90)
• 28.9Mbps (60)
•14.4Mbps (30)
· 21.7Mbps (45)
· 7.2Mbps (15)
IEEE.802.11n.5GHz(HT20/40):
• 144.4Mbps (300) · 130Mbps (270)
• 115.6Mbps (240) · 86.7Mbps (180)
• 72.2Mbps (150) · 65Mbps (135)
• 57.8Mbps (120) · 43.3Mbps (90)
• 28.9Mbps (60)
•14.4Mbps (30)
· 21.7Mbps (45)
· 7.2Mbps (15).
External.Antenna.Type
• Two (2) detachable Antennas
Operating.Temperature
• 32°F to 104°F ( 0°C to 40°C)
Humidity
• 95% maximum (non-condensing)
Safety.&.Emissions
• FCC
• IC
Dimensions
• L = 7.6 inches
• W = 4.6 inches
• H = 1.2inches
Warranty
• 1 Year
IEEE.802.11g:
• 54Mbps • 48Mbps • 36Mbps
1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range.
2 Frequency Range varies depending on country’s regulation
3 The DIR-825 does not include 5.25-5.35GHz & 5.47-5.725GHz in some regions.
D-Link DIR-825 User Manual 132
Appendix D - Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g. DIR-825)
• Hardware Revision (located on the label on the bottom of the router (e.g. rev C1))
• Serial Number (s/n number located on the label on the bottom of the router).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions and answers to technical issues.
For.customers.within.the.United.States:
Phone.Support:
(877) 453-5465
Internet.Support:
http://support.dlink.com
For.customers.within.Canada:
Phone.Support:
(800) 361-5265
Internet.Support:
http://support.dlink.ca
D-Link DIR-825 User Manual 133
Appendix E - GNU General Public License
GPL Code Statement
This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL code and LGPL code used in this product, are available to you at: http://tsd.dlink.com.tw/GPL.asp
The GPL code and LGPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. For details, see the GPL code and the LGPL code for this product and the terms of the GPL and LGPL.
WRITTEN OFFER FOR GPL AND LGPL SOURCE CODE
Where such specific license terms entitle you to the source code of such software, D-Link will provide upon written request via email and/or traditional paper mail the applicable GPL and LGPLsource code files via CD-ROM for a nominal cost to cover shipping and media charges as allowed under the GPL and LGPL.
Please direct all inquiries to:
Email: [email protected]
Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
17595 Mt. Herrmann Street
Fountain Valley, CA 92708
GNU.GENERAL.PUBLIC.LICENSE
Version.3,.29.June.2007
Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
D-Link DIR-825 User Manual 134
Appendix E - GNU General Public License
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the
GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
D-Link DIR-825 User Manual 135
Appendix E - GNU General Public License
.TERMS.AND.CONDITIONS
0..Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
1..Source.Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language.
D-Link DIR-825 User Manual 136
Appendix E - GNU General Public License
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2..Basic.Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force.
You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.
Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
D-Link DIR-825 User Manual 137
Appendix E - GNU General Public License
3..Protecting.Users’.Legal.Rights.From.Anti-Circumvention.Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the
WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4..Conveying.Verbatim.Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5..Conveying.Modified.Source.Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.
This requirement modifies the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
D-Link DIR-825 User Manual 138
Appendix E - GNU General Public License
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6..Conveying.Non-Source.Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these ways: a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the
Corresponding Source fixed on a durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the
Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and
Corresponding Source of the work are being offered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
D-Link DIR-825 User Manual 139
Appendix E - GNU General Public License
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information.
But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented
(and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
7..Additional.Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions.
D-Link DIR-825 User Manual 140
Appendix E - GNU General Public License
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in certain cases when you modify the work). You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms: a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or d) Limiting the use for publicity purposes of names of licensors or authors of the material; or e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
D-Link DIR-825 User Manual 141
Appendix E - GNU General Public License
8..Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this
License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10.
9..Acceptance.Not.Required.for.Having.Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License.
Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10..Automatic.Licensing.of.Downstream.Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
D-Link DIR-825 User Manual 142
Appendix E - GNU General Public License
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11..Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent
(such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients.
“Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
D-Link DIR-825 User Manual 143
Appendix E - GNU General Public License
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the nonexercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or
(b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
12..No.Surrender.of.Others’.Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13..Use.with.the.GNU.Affero.General.Public.License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version
3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such.
14..Revised.Versions.of.this.License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License
“or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU
General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
D-Link DIR-825 User Manual 144
Appendix E - GNU General Public License
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
15..Disclaimer.of.Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16..Limitation.of.Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17..Interpretation.of.Sections.15.and.16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
D-Link DIR-825 User Manual 145
Appendix F - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited.Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
D-Link DIR-825 User Manual 146
Appendix F - Warranty
Limited.Software.Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by
D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.
Non-Applicability.of.Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting.A.Claim.(USA):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a
Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https:// rma.dlink.com/.
D-Link DIR-825 User Manual 147
Appendix F - Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Submitting.A.Claim.(Canada):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will be done. The registration is not considered a proof of purchase.
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
D-Link DIR-825 User Manual 148
Appendix F - Warranty
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard
Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What.Is.Not.Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer.of.Other.Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
D-Link DIR-825 User Manual 149
Appendix F - Warranty
Limitation.of.Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing.Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners.
Copyright.Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2011 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE.Mark.Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
D-Link DIR-825 User Manual 150
Appendix F - Warranty
FCC.Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC.Caution:.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Operations in the 5.15-5.25GHz / 5.470 ~ 5.725GHz band are restricted to indoor usage only.
IMPORTANT.NOTICE:
FCC.Radiation.Exposure.Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.
If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
D-Link DIR-825 User Manual 151
Appendix F - Warranty
ICC.Notice:
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT.NOTE:
IC.Radiation.Exposure.Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
(i) The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems;
(ii) The maximum antenna gain (2dBi) permitted (for devices in the band 5725-5825 MHz) to comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3).
In addition, users should also be cautioned to take note that high-power radars are allocated as primary users (meaning they have priority) of the bands 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Règlement.d’Industry.Canada.
Les conditions de fonctionnement sont sujettes à deux conditions:
(1) Ce périphérique ne doit pas causer d’interférence et.
(2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de ce périphérique.
D-Link DIR-825 User Manual 152
Appendix G - Registration
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Version 3.0
November 30, 2011
D-Link DIR-825 User Manual 153
Télécharger
Lien public mis à jour
Le lien public vers votre chat a été mis à jour. Vous pouvez afficher et gérer vos liens de chat après inscription ici.
Lien public du document
Publicité