ECHO PB-500H, PB-500T Power Blower Operator's Manual

PDF

Документ

Power Blower

Operator's Manual

MODELS

PB-500T

warning

Users of this equipment risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. ECHO provides an operator’s manual. It must be read and understood for proper and safe operation. Failure to do so could result in serious injury.

X7505200006

X750011586

04/13

nTroduCTIon

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-thejob-dependability. Read and understand this manual. You will find it easy to use and full of helpful operations tips and

SAFETY messages.

The operaTor

s manual

Keep it in a safe place for future reference. Contains specifications and information for safety, operation, maintenance, storage, and assembly specific to this product.

Power Blower

Operator's Manual

MODELS PB-500H

PB-500T

WARNING

Read rules for safe operation and all instructions carefully. ECHO provides this

Operator's Manual which must be read and understood for proper and safe operation.

X7505200000

X750011580

04/08

able of

onTenTs

Introduction ................................................................2

- The Operator's Manual .......................................2

Safety .........................................................................3

- Manual Safety Symbols and Important

Information .........................................................3

- International Symbols .........................................3

- Personal Condition and Safety Equipment .........3

- Equipment Check ................................................6

Emission Control .......................................................6

Description .................................................................7

Contents .................................................................. 11

Assembly..................................................................12

- Install Blower Pipes / Stick Handle (PB-500H) 12

- Install Blower Pipes (PB-500T) ........................13

Operation ..................................................................14

- Fuel ...................................................................14

- Starting Cold Engine .........................................16

- Starting Warm Engine .......................................17

- Stopping Engine ................................................17

- Operating Blower ..............................................18

Maintenance .............................................................19

- Skill Levels .......................................................19

- Maintenance Intervals .......................................19

- Air Filter ...........................................................20

- Fuel Filter ..........................................................20

- Spark Plug .........................................................21

- Cooling System .................................................21

- Exhaust System .................................................22

- Carburetor Adjustment ......................................24

- High Altitude Operation ................................24

Troubleshooting .......................................................25

Storage .....................................................................26

Specifications ...........................................................27

Warranty Statements ................................................28

Servicing Information ..............................................32

- Parts/Serial Number ..........................................32

- Service ..............................................................32

- ECHO Consumer Product Support ...................32

- Warranty Registration .......................................32

- Additional or Replacement Manuals ................32

Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.

P ower

B lower o

Perator

' s

M anual s

afeTy manual safeTy symbols and ImporTanT InformaTIon

Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

DangEr

The safety alert symbol accompanied by the word

“DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.

warning

The safety alert symbol accompanied by the word

“WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided.

CaUTiOn

The safety alert symbol accompanied by the word

“CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided.

InTernaTIonal symbols

Symbol form/shape

Symbol description/application

Symbol form/shape

Symbol description/application read and understand

Operator's Manual.

Fuel and oil mixture

CIRCLE AND SLASH SyMBOL

This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in serious or fatal injury.

NOTE

This enclosed message provides tips for use, care and maintenance of the unit.

IMPORTANT

The enclosed message provides information necessary for the protection of the unit.

Symbol form/shape

Symbol description/application

Emergency stop

Symbol form/shape

Symbol description/application ignition

On/OFF

Carburetor adjustment

- Low speed mixture wear eyes, ears and head protection

Finger Severing Primer bulb

Carburetor adjustment

- idle speed

Carburetor adjustment

- High speed mixture

Hot

Surface wear hand protection. Use two handed.

wear slip resistant foot wear.

Safety/alert

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"run"

Position

(Choke Open)

DO nOT allow flames or sparks near fuel.

DO nOT smoke near fuel.

idle Speed Fast Speed

personal CondITIon and safeTy equIpmenT

warning

Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit.

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.

Hand Protection

Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Gloves also reduce the transmission of machine vibration to your hands.

Breathing Protection

Wear a facemask to protect against dust.

Hearing Protection

ECHO recommends wearing hearing protection whenever unit is used.

Proper Clothing

Wear snug fitting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth.

Wear sturdy work shoes with nonskid soles:

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

Wear no-slip, heavy duty work gloves.

Keep long hair away from engine and air intake. Retain hair with cap or net.

Hot Humid Weather

Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.

warning

The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine. In the absence of such information, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended, because the minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands, and wrists.

• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held power equipment is not required.

• If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.

P ower

B lower o

Perator

' s

M anual

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.

Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position.

Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive movement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented.

DangEr

Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.

Read the Manuals

• Provide all users of this equipment with the Operator’s Manual for instructions on Safe Operation.

Clear the Work Area

• Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use.

• Take wind conditions into account: avoid open doors and windows.

• Do not point blower at people or animals.

Keep a Firm Grip

• Hold the front and rear handles with both hands, with thumbs and fingers encircling the handles.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach.

Avoid Hot Surfaces

• Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation.

equIpmenT CheCk

warning

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Do not use blower if any part is missing or damaged.

• Have repairs done only by an authorized ECHO Service dealer.

• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.

warning

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings.

• ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.

• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

warning

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized servicing dealer before using.

mIssIon

onTrol

(

exhausT

evaporaTIve

)

EPA 2010 and Later and/or C.A.R.B. TIER III

The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine

Family on the Emission Control Information label (sample below) is “C”, “K”, or “T”, the emission control system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions). Evaporative emissions for California models are only applicable to fuel tanks.

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY; information on label varies by engine FAMILY).

PRODUCT EMISSION DURABILITy (EMISSION COMPLIANCE PERIOD)

The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual.

P ower

B lower o

Perator

' s

M anual d

esCrIpTIon

PB-500H

Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.

Hot Decal (near muffler)

10 3

General Warning Decal (located on blower housing)

Sound Label (located on blower housing)

70 Category ii

Measured at 50 ft. (15m) per anSi B175.2

1. SAFETy DECAL - Lists important safety precautions.

2. SPARK PLUG - Provides spark to ignite fuel mixture.

3. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALyST - The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris.

4. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.

5. AIR CLEANER - Contains replaceable air filter element.

6. FUEL TANK CAP - Covers and seals fuel tank.

7. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.

8. CHOKE - Move lever UP to close choke ( ) (starting position) and for emergency stopping. Move DOWN to open choke ( ) (run position).

9. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times.

10. THROTTLE POSITION LEVER/STOP SWITCH - Combination stop switch and variable speed throttle lever.

When the lever is moved all the way forward the blower is at Wide Open Throttle (W.O.T.). When the lever is moved rearward to detent, the blower is at idle. When the lever is moved rearward past the idle detent the blower will stop.

11. HANDLE - Rotates downward for throttle control access. Spring loaded for flexible operation.

12. STICK HANDLE - Provides comfortable grip for directing air flow.

13. BLOWER PIPES - Exclusive positive locking system.

14. FLEXIBLE PIPE - Allows for full range of movement.

P ower

B lower o

Perator

' s

M anual

PB-500T

Hot Decal (near muffler)

10 11

General Warning Decal (located on blower housing)

Sound Label (located on blower housing)

70 Category ii

Measured at 50 ft. (15m) per anSi B175.2

1. SAFETy DECAL - Lists important safety precautions.

2. SPARK PLUG - Provides spark to ignite fuel mixture.

5. AIR CLEANER - Contains replaceable air filter element.

6. FUEL TANK CAP - Covers and seals fuel tank.

7. SHOULDER HARNESS - Used to support unit on operator's back. The straps are adjustable.

8. CHOKE - Move lever UP to close choke ( ) (starting position) and for emergency stopping. Move DOWN to open choke ( ) (run position).

10. HANDLE - Used by operator to direct and control air flow.

11. COMBINATION THROTTLE POSITION / STOP SWITCH BUTTON - Controls engine speed and turns ignition on or off. Forward position - STOP. First detent position - IDLE. Move button back to increase speed, forward to decrease speed. Use Throttle Position Button to set and hold blower speed for continuous operation.

12. THROTTLE TRIGGER - Spring - loaded Throttle Trigger controls engine speed. Releasing Trigger returns engine to speed set by Throttle Position Stop Switch Button. Always release trigger and allow engine to return to idle before shutting off with Throttle Position Stop Switch Button. Use Throttle Trigger to vary blower speed settings for intermittent operation.

13. LOCKING KNOB - Allows operator to adjust handle position for optimum comfort and control.

14. BLOWER PIPES - Exclusive positive locking system.

15. FLEXIBLE PIPE - Allows for full range of movement.

onTenTs

PB-500H

___ 1 - Power Head

___ 1 - Flex Pipe

___ 1 - Pipe w/swivel

___ 1 - Straight Pipe

___ 1 - Straight Pipe w/decal

___ 1 - Operator's Manual

___ 1 - Emission Control Warranty Statement

___ 1 - Warranty Registration Card

___ 1 - Plastic Bag

___ 2 - Clamps w/screws

___ 1 - Stick Handle

___ 1 - Bolt 6x45

___ 1 - Washer 6

___ 1 - Wing nut

___ 1 - Echo Power Blend X TM 2-stroke oil sample

P ower

B lower o

Perator

' s

M anual

Power Blower

Operator's Manual

MODELS PB-500H

PB-500T

WARNING

Read rules for safe operation and all instructions carefully. ECHO provides this

Operator's Manual which must be read and understood for proper and safe operation.

X7505200000 X750011580

04/08

ECHO LIMITED WARRANTY STATEMENT FOR

PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010

ECHO'S RESPONSIBILITY

ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.

Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions.

THIS LIMITED

WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL

PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.

Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers

To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you.

The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.

PRODUCT WARRANTY PERIOD

5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase.

EXCEPTIONS:

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines

• Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a period of purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.

• ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s

• All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit.

COMMERCIAL APPLICATION

•

• producing use will be covered by this limited warranty for one (1) year from the date of purchase.

2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for two (2) years from the date of purchase.

EXCEPTIONS:

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines,

• ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s manual for string head installation and maintenance instructions.

RENTAL APPLICATION - 90 DAYS WARRANTY

• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.

* ECHO’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PROdUCT wARRANTy PERIOd section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production.

PB-500T

___ 1 - Power Head

___ 1 - Flex Pipe

___ 1 - Pipe w/swivel

___ 1 - Straight Pipe

___ 1 - Straight Pipe w/decal

___ 1 - Operator's Manual

___ 1 - Emission Control Warranty Statement

___ 1 - Warranty Registration Card

___ 1 - Plastic Bag

___ 2 - Clamps w/screws

___ 1 - Guide Loop

___ 1 - Echo Power Blend X TM 2-stroke oil sample

Power Blower

Operator's Manual

MODELS PB-500H

PB-500T

WARNING

Read rules for safe operation and all instructions carefully. ECHO provides this

Operator's Manual which must be read and understood for proper and safe operation.

X7505200000 X750011580

04/08

ECHO'S RESPONSIBILITY

ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions.

THIS LIMITED

WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty

Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.

OWNER’S RESPONSIBILITY

PRODUCT WARRANTY PERIOD

RESIDENTIAL APPLICATION

•

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines are warranted for the

• Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.

•

1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for one

EXCEPTIONS:

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines, are warranted for the life* of the product on parts only.

• Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.

• All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit.

12 a

ssembly

PB-500H

warning

Never perform maintenance or assembly procedures with engine running or serious personal injury may result.

B a

InsTall blower pIpes

sTICk handle

1. Assemble clamps (A) onto both ends of flexible pipe (B).

2. Assemble straight pipe with swivel (C) into flexible pipe (B).

3. Assemble flexible pipe (B) to elbow (D) on blower.

NOTE

A light lubricant may be used to ease assembly of flexible pipe to blower elbow.

4. Tighten clamps (A).

5. Loosen wing nut (E) completely and expand stick handle clamp

(F).

6. Align notches (G) in handle clamp with pipe pegs (H). Stick handle should be angled away from operator.

7. Slide stick handle onto pipe with swivel (C)

8. Position stick handle for comfortable operation, and tighten wing nut (E).

9. Assemble straight pipe (J) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection.

10. Assemble straight pipe with decal (K) to straight pipe (J) as in step

NOTE

Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two straight pipes and install according to instructions 9 & 10.

D a

B a

E g g

P ower

B lower o

Perator

' s

M anual

PB-500T

warning

Never perform maintenance or assembly procedures with engine running or serious personal injury may result.

InsTall blower pIpes ( T)

1. Place guide loop (G) across clamp, and turn until clip fully engages clamp band.

NOTE

Clamp with cable guide loop (G) fits elbow end of flexible pipe (B).

2. Assemble clamps (A) onto both ends of flexible pipe (B).

3. Assemble flexible pipe (B) to elbow (D) on blower. Position guide loop (G) on inside (blower side) of flexible tube and tighten clamp

(A).

NOTE

A light lubricant may be used to ease assembly of flexible pipe to blower elbow.

NOTE

Hang handle freely from blower to assure throttle cable is not twisted before installing handle (E).

4. Position cable between the elbow (D) and frame and along the top of the flexible pipe. Loosen knob (H) on handle (E). Align notch in handle with tabs (F). Install onto swivel pipe (C) past long ridges in pipe.

5. Assemble swivel pipe (C) into flexible pipe (B) and tighten clamp

(A).

6. Clip throttle cable into throttle cable guide loop (G).

7. Move handle (E) to desired position. Tighten knob (H) hand tight.

8. Assemble straight pipe (I) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection.

9. Assemble straight pipe with decal (J) to straight pipe (I) as in step

NOTE

g a

H g g i

J a

D a B a C

14 o

peraTIon

warning

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving. Wear gloves to protect hands from sharp edges and hot surfaces.

warning

Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention requirements.

NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual.

fuel

warning

Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are

NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to

10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards must be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD certified oil, such as Echo premium Power Blend X TM , will void the two-stroke engine warranty. (Emission related parts only are covered for five years, regardless of two-stroke oil used, per the statement listed in the Emission Defect Warranty Explanation.)

IMPORTANT

Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals.

P ower

B lower o

Perator

' s

M anual

Handling Fuel

DangEr

Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow flames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

• DO NOT overfill fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting the engine.

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of gasoline.

2. Add the proper amount of 2-stroke oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames.

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.

Gas

Gallons

Fuel to Oil Mix - 50:1 ratio

U.S.

METRIC

Oil

FL. oz.

Gas

Liter

Oil cc.

2.6

5.2

160

400

sTarTIng Cold engIne

• Recoil starter: Use short pulls - only 1/2-2/3 of rope length for starting. Do not allow the rope to snap back in. Always hold the unit firmly.

• (PB-500H): Rotate spring loaded throttle arm downward to a comfortable operating position.

PB-500H

1. Throttle Lever

Move throttle position lever (A) midway between idle and full throttle positions.

PB-500H

PB-500T

1. Throttle Position / Stop Switch Button

Slide Throttle Position / Stop Switch Button (A) back to idle position.

PB-500T

PB-500H, PB-500T

2. Choke

Move choke (C) up to Cold Start position ( ).

3. Purge Bulb

Pump purge bulb (D) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.

4. Recoil Starter

Pull recoil starter handle (E) until engine fires, or a maximum of 5 pulls.

5. Choke

After engine fires (or 5 pulls), move choke lever (C) to “Run” (

) position, then pull starter handle/rope until engine starts and runs.

Allow unit to warm up at idle for several minutes.

NOTE

If engine does not start with choke in “Run” position after 5 pulls, move choke to “Cold Start” ( ) position, and repeat steps 4 & 5.

6. Throttle Lever

Allow engine to warm up for several minutes before use.

7. Throttle Lever

After engine warm-up, move throttle lever gradually to increase engine RPM to desired operating speed.

D a

sTarTIng warm engIne

The starting procedure is the same as Cold Start except DO NOT close the choke.

PB-500H

1. Throttle Lever

Move throttle position lever (A) midway between idle and full throttle positions.

PB-500T

1. Throttle Position / Stop Switch Button

Slide Throttle position / Stop switch Button(A) back to idle position.

PB-500H, PB-500T

2. Purge Bulb

Pump purge bulb (D) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.

3. Recoil Starter

Pull recoil starter handle (E) and engine should start. Do not use choke (C).

NOTE

If engine does not start after 5 pulls, use cold start procedures.

sToppIng engIne

PB-500H

1. Throttle Lever

Move throttle lever (A) to IDLE DETENT position and allow engine to return to idle before shutting off engine.

2. Throttle Lever

Move throttle lever (A) to "O" (Stop) position.

PB-500T

1. Throttle Position / Stop Switch Button

Release throttle trigger. Move Throttle Position / Stop Switch Button (A) forward to idle position and allow engine to return to idle before shutting off engine.

2. Throttle Position / Stop Switch Button

Move Throttle Position / Stop Switch Button (A) all the way forward to STOP position.

P ower

B lower o

Perator

' s

M anual

PB-500H

PB-500T

PB-500H

PB-500T a a

warning

If engine does not stop when stop switch is moved to STOP position:

• Be certain engine is at idle, otherwise engine may continue to run.

• Close choke - COLD START position - to stall engine.

• Have your ECHO dealer repair stop switch before using blower again.

operaTIng blower

warning

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body.

warning

Always wear safety glasses, hearing protection, a face filter mask and take all safety precautions or serious personal injury may result.

Do not point the blower pipe in the direction of people or pets.

IMPORTANT

Use reduced speed only when performing light-duty tasks or to comply with local noise regulations. Continuous low speed operation may allow fuel/oil residue to build-up on the piston and cause rapid build-up of carbon on the spark arrestor screen, resulting in overheating and engine damage. To reduce harmful build-up, run engine at wide open throttle for at least 5 minutes every hour, and inspect/clean the spark arrestor screen after approximately 40 hours of operation.

Read the Safety Section on pages 3 - 6 carefully.

IMPORTANT

To avoid engine damage due to over-revving, do not block blower pipe opening.

1. Use only during appropriate hours.

2. Allow the engine to warm up at a fast idle for a few minutes.

3. PB-500H: Set engine speed with throttle lever (A).

PB-500T: Control engine speed with throttle trigger (B), or for continuous use, set engine speed with Combination Throttle Position / Stop Switch Button (A).

4. Use lower speed to blow dry leaves from walks, patios and drives.

5. Additional speed may be necessary to clean grass and leaves from a lawn or flower bed.

6. Higher speed may be necessary to move gravel, dirt, snow, bottles or cans from a driveway, street, parking lot or stadium.

7. Always stop unit using stop engine procedure.

NOTE

Never use a higher speed setting than necessary to perform a task.

Remember, the higher the engine speed, the louder the blower noise. Minimize dust by using blower at lower speeds and by dampening material with water/mist when necessary. Keep debris on your property.

Be Smart - be a good neighbor.

PB-500H

PB-500T a a

P ower

B lower o

Perator

' s

M anual

19 m

aInTenanCe

warning

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.

Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs.

skIll levels

Level 1 = Easy to do. Common tools may be required.

Level 2 = Moderate difficulty. Some specialized tools may be required.

ECHO offers REPOWER TM Maintenance Kits and Parts to make your maintenance job easier.

maInTenanCe InTervals

COMPONENT / SYSTEM

Air Filter

Choke Shutter

Fuel Filter

Fuel Cap Gasket

Fuel System

Spark Plug

Cooling System

Muffler Spark Arrestor

MAINTENANCE

PROCEDURE

Inspect/Clean

Inspect/Replace

Inspect/Clean/Replace

Inspect/Clean

Inspect/Clean/Replace

REQ'D

SKILL

LEVEL

DAILY OR

BEFORE USE

I / C *

I / C

I (1) *

I / C

EVERY

REFUEL

I (1) *

3 MONTHS YEARLY

R *

I *

I / C / R *

I / R *

Cylinder Exhaust Port

Recoil Starter Rope

Inspect/Clean/Decarbon

Inspect/Clean

1 I / C *

I / C

Screws/Nuts/Bolts Inspect/Tighten/Replace 1 I *

MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN

IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.

* All recommendations to replace are based on the finding of damage or wear during inspection.

R *

aIr fIlTer

Level 1.

Parts required: Repower TM Tune Up Kit

NOTE

Clean daily.

1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area.

2. Remove air filter cover. Brush dirt from inside cover.

3. Remove air filter and lightly brush debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed.

4. If filter can be reused, be certain it:

• Fits tightly in the air filter cavity.

• Is installed with the original side out.

5. Install air filter cover.

fuel fIlTer

Level 1.

Parts required: Repower TM Tune Up Kit

DangEr

Fuel is VERy flammable. Use extreme care when mixing, storing or handling.

1 . Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank.

2. Use the “fuel line hook” to pull the fuel line and filter from the tank.

3. Remove the filter from the line and install the new filter.

NOTE

Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the

United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.

When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replacement part.

spark plug

Level 1.

Parts Required: Repower TM Tune Up Kit

IMPORTANT

Use only NGK BPM8Y spark plug (BPMR8Y in Canada) otherwise severe engine damage may occur.

1. Remove spark plug , and check for fouling, worn and rounded center electrode.

2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).

CoolIng sysTem

Level 2.

Parts Required: None, if you are careful.

IMPORTANT

To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the cylinder.

• Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance”. Any failure attributed to lack of maintenance is not warranted.

Cleaning Grill

1. Remove accumulated debris from intake grill between backpack frame and blower housing.

P ower

B lower o

Perator

' s

M anual

0.65 mm

(0.026 in.)

Cleaning Cylinder Fins

1. Disconnect spark plug lead from spark plug.

2. Remove engine cover (five screws), pull cover away from engine.

3. Clean cylinder fins (A) to allow cooling air to pass freely.

4. Replace cover and tighten screws.

5. Connect spark plug lead.

exhausT sysTem

Spark Arrestor Screen

Level 2.

Parts Required: Spark arrestor screen, Gasket

IMPORTANT

Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically.

1. Remove spark plug and engine cover (five screws).

2. Remove spark arrestor cover (A), gasket (B) and spark arrestor screen (C) from muffler. Replace screen if plugged with carbon deposits.

3. Install spark arrestor screen, gaskets, and cover.

4. Install spark plug and engine cover.

B a a

P ower

B lower o

Perator

' s

M anual

Exhaust Port Cleaning

Level 2

Parts Required: As needed: Muffler gasket

1. Remove spark plug lead from spark plug, and remove engine cover.

2. Place piston at top dead center. Remove muffler (A) and muffler gasket (B ).

3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port.

IMPORTANT

Never use a metal tool to scrape carbon from the exhaust port.

Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder.

4. Inspect muffler gasket, and replace if damaged.

5. Install muffler gasket and muffler.

6. Tighten muffler mounting bolts (or nuts) to 80-95 in•lbf

(90-110 kgf•cm).

7. Install engine cover and attach spark plug lead.

8. Start engine, and warm to operating temperature.

9. Stop engine, and re-tighten mounting bolts (or nuts) to specifications.

B a

CarbureTor adjusTmenT

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the breakin period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required.

High Altitude Operation

This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level

(ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 1,100 feet ASL the carburetor may need to be adjusted by an authorized ECHO service dealer.

IMPORTANT

If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when operating the engine below

1,100 feet ASL, otherwise severe engine damage may result.

Level 2.

Parts required: None.

NOTE

Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.

Idle Adjustment

Before adjustment make sure that:

• Air filter is clean and properly installed.

• Spark arrestor screen and muffler are free of carbon.

• Blower pipes are installed.

1. Start engine, run at idle for one minute.

2. Complete warm up by running at full throttle for 5 minutes, operating choke twice to clear air from carburetor chambers.

3. Check idle speed and reset if necessary. If a tachometer is available, idle speed screw (A) should be set to the specifications found on "Specifications" Page of this manual. Turn idle screw (A) clockwise to increase idle speed; counter clockwise to decrease idle speed.

P ower

B lower o

Perator

' s

M anual

roubleshooTIng

P r o b l e m

E n s g i t a n e d o s tr s t e s a c r h tr a a n t' r n k d / s -

C h e c k

F u e l a t c a r b u r e t o r

F u e l a t c y il n d e r

S o p a r k f p l u g a t w e ri n e d

S p a r k a t p l u g

A ri f tli e r

F u e l f tli e r

T R O U B L E S H O O T I N G C H A R T

S t a t u s C a u s e

N o f u e l a t c a r b u r e t o r

N o f u e l a t c y il n d e r

M u lff e r w e t w ti h f u e l

N o s p a r k

A ri f tli e r d i tr y

F u e l f tli e r d i tr y

F u e l v e n t p l u g g e d

P l u g d i tr /y w o r n

C u u a e e l l r b u il r s n rt e a i n e r lc o g g lc o g e d g e d e t o r

C a r b u r e t o r

F u e l M i tx u r e t o o ir c h

S t o p

I n t l e c t e lr o ir s w c a c k l ti s c h p w r o ti o b l ff e m c h

P l p o o u a v g lu r k e e r e d d e g d a p f w e ti c w h it ti h f u i n c o v e c a e l rr e c t r b o n

N o r m a l w e a r

C o n t f u e l a m i n a n t s r/ e is d u e s i n

R e m e d y

S l l e e e e a n a n o r o r y o u r r r e p e

E p c l a c e l a h o c e d e a l e r

S e e y o u r E c h o d e a l e r

O p

S l e d e e a n e uj n s y t c o r/ c h e u r a o p r k e l a c e b

E u c r e t h o a o r ri d e f tli e a l e r r

T u r n

S e e e e s w y y o u o u r r ti c h

E c t o h o

O N d e

E c h o d e a l e r a l e r

A d

R l l e e a e p uj s n t a n l a t o o r o r c e

r r p l

6 5 m m e e p p u g l l a c e a c e

( 0 .

0 2 6 i n ).

C l e a n o r r e p l a c e

R e p l a c e

C o n t a m i n a n t s r/ e is d u e s i n f u e l

N o r m a l w e a r

C l e a n o r r e p l a c e

C l e a n a n d a d uj s t o r r e p l a c e

E b a n d u c p g t i d o e s r c o n e l e p i e e r r s n a e r u n s , o t o r yl t e

E n n g i o t n e c d o e s r a n k b l

E n o w g i n e r e w w o e a r k d o r k / u n e v o r u e n s s n

, i s e n t'

C o o a il r b n g u r

S e y t o s t r e m

S p a r k A rr e s t o r S c r e e n

N / A

I m p r o p e r a d uj s t m e n t V i b r a it o n

C d i o o tr il n g

/y p l u s y g g s t e e d m

S p a r k a p l u rr e s g g t o r e d s c r e e n

N / A

E d i tr tx e n d e d

/y d u s t y l o o p e r a c a it o it o n n s i n

N o r m a l w e a r

I n t e r n a l e n g i n e p r o b l e m

B l

F u e l v e n t p o a w r e k r

P p l i u p g e

P i

P i p p i e p e e d a lc l o o m g o a g s g e e e d d

V i u b r li d a it u p o n o f d

W e a /r M i s u s e e b ir s

A d uj s t

C l e a n

R e p l a c e

S e e y o u r E c h o d e a l e r

U n lc o g iT g h t e n

R e p l a c e

DangEr

Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.

26 s

Torage

warning

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.

Long Term Storage (Over 30 Days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:

1. Store unit in a dry, dust free place, out of the reach of children.

DangEr

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.

2. Place the stop switch in the "STOP" position.

3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.

4. Perform all periodic lubrication and services that are required.

5. Tighten all screws and nuts.

6. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.

7. A. Allow engine to cool then remove the spark plug

and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke

engine oil into the cylinder through the spark plug

hole.

B. Pull the recoil starter handle 2-3 times to

distribute the oil inside the engine.

C. Observe the piston location through the spark

plug hole. Pull the recoil handle slowly until the

piston reaches the top of its travel and leave it

there.

8. Install the spark plug (do not connect ignition cable).

9. Remove blower pipe assembly from unit.

P ower

B lower o

Perator

' s

M anual

27 s

peCIfICaTIons

MODEL ---------------------------------------------------- PB-500H, PB-500T

Length PB-500H ------------------------------------------ 380mm (15.0 in.)

Length PB-500T ------------------------------------------- 328mm (12.9 in.)

Width PB-500H ------------------------------------------- 545 mm (21.5 in.)

Height PB-500H ------------------------------------------- 490 mm (19.3 in.)

Height PB-500T -------------------------------------------- 490 mm (19.3 in.)

Weight (dry) PB-500H ----------------------------------- 9.4 kg (20.7 lb.)

Weight (dry) PB-500T ----------------------------------- 9.2 kg (20.3lb.)

Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine

Displacement ----------------------------------------------- 50.8cc (3.10 cu. in.)

Bore ---------------------------------------------------------- 43.0 mm (1.69 in.)

Stroke -------------------------------------------------------- 35.0 mm (1.38 in.)

Carburetor--------------------------------------------------- Diaphragm model w/purge bulb

Ignition System -------------------------------------------- Flywheel Magneto, capacitor discharge ignition type

Spark Plug -------------------------------------------------- NGK BPM8Y Gap 0.65 mm (0.026 in.)

Exhaust System -------------------------------------------- Spark arrestor muffler or spark arrestor muffler with catalyst

Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ---------------------------------------------- 50 : 1 Power Blend X TM ISO-L-EGD (ISO/CD 13738) and

J.A.S.O. M345- FD, two-stroke, air-cooled engine oil.

Gasoline ----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85.

Oil ------------------------------------------------------------ Power Blend X TM Premium Universal 2-Stroke Oil

Fuel Tank Capacity ---------------------------------------- 1.81 lit. (61.2 US fl. oz.)

Recoil Starter System ------------------------------------- Automatic Recoil Starter Centrifugal Type

Idle Speed -------------------------------------------------- 2,650 (RPM)

Wide Open Throttle Speed ------------------------------- 6,650 (RPM)

Average Air Speed w/pipes (MPH) ---------------------- 72.87 m/sec (163 mph)

Maximum Air Speed w/pipes (MPH) ------------------- 87.17 m/sec (195 mph)

Maximum Air Volume ------------------------------------ 13.17 m 3/ min. (465 cu. ft./min.)

Sound level at 50 ft. dB(A) scale per ANSI B175.2 -- 70 dB(A)

28 w

arranTy

TaTemenTs

ECHO LIMITED WARRANTY STATEMENT FOR

PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010

ECHO'S RESPONSIBILITY

ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.

THIS LIMITED

WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL

PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.

Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.

OWNER’S RESPONSIBILITY

PRODUCT WARRANTY PERIOD

RESIDENTIAL APPLICATION

• 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase.

EXCEPTIONS:

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines are warranted for the life* of the product on parts only.

• Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.

• All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit.

COMMERCIAL APPLICATION

• 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for one (1) year from the date of purchase.

• 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for two (2) years from the date of purchase.

EXCEPTIONS:

• For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines, are warranted for the life* of the product on parts only.

• All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit.

RENTAL APPLICATION - 90 DAYS WARRANTY

• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.

P ower

B lower o

Perator

' s

M anual

PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES

• 90-day residential, or non-income producing warranty

• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty

ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS

This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD

13738 and JASO M345FD Standards.

ECHO Power Blend™ Two-Stroke Oil is a premium two-stroke oil specifically formulated to meet ISO-

L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.

THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:

• Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD

Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO M345FD

Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per the statement listed in the EPA or California Emission Defect Warranty Explanation.

• damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.

• Engine damage caused by use of ether or any starting fluids.

• damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as listed in your operator’s manual.

• Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.

• damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.

• defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use of unauthorized attachments.

• Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.

• Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the warranty period.

• Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.

• Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's

Manuals.

• Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester screen.

• Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.

• damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply with recommended grease or oil change intervals.

• damage caused by loading SHREd 'N' VAC ® beyond recommended capacity.

• damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers.

• Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.

It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting

WWW.ECHO-USA.COM. your receipt of purchase including date, model and serial number must be maintained and presented to an authorized

ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO

Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.

DISCLAIMER OF IMPLIED WARRANTIES

This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE

OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO and its affiliated companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein.

This limited warranty may be modified only by ECHO.

99922201032

11/18/2011

noTes

P ower

B lower o

Perator

' s

M anual

ervICIng

nformaTIon parTs

serIal number

Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO

Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below.

Model No. _________________SN. ___________________

servICe

Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your unit for Warranty service/repairs, proof of purchase is required.

eCho Consumer produCT supporT

If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the ECHO

Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.

warranTy regIsTraTIon

To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at www.echo-usa.com or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you.

DEaLEr? Call

1-800-432-ECHO

1-800-432-3246

or www.echo-usa.com

COnSUMEr PrODUCT

SUPPOrT

1-800-673-1558

8:30 - 4:30 Mon - Fri C.S.T.

addITIonal or replaCemenT manuals

Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echousa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the

ECHO Web Site for updated information.

Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.

(H) P02311001001/P02311999999

(H) P33011001001/P33011999999

(H) P02112001001/P02112999999

(H) P31312001001/P31312999999

ECHO, inCOrPOraTED

400 O

akwOOd

R

Oad

L

ake

Z

uRich

, iL 60047

www.echo-usa.com

(T) P02011001001/P02011999999

(T) P32911001001/P32911999999

(T) P02212001001/P02212999999

(T) P31212001001/P31212999999

Привіт! Я чат-бот зі штучним інтелектом, спеціально навчений допомагати вам з ECHO PB-500H. Я ретельно переглянув документ і можу допомогти вам знайти точну інформацію, яка вам потрібна, або пояснити вміст чіткими та простими словами. Незалежно від того, чи шукаєте ви вказівки щодо конкретних функцій, кроки з усунення несправностей або загальне використання, не соромтеся задавати свої запитання. Чим більше деталей ви надасте про свої проблеми чи потреби, тим точніше та ефективніше я зможу вам допомогти!

Асистент друкує

Асистент не в мережі. Будь ласка, спробуйте пізніше.

Зміст

Схоже, ви потрапили на документ, написаний кількома мовами, включаючи ту, яка не є вашою рідною. Ви можете скористатися наведеними нижче посиланнями, щоб тимчасово приховати сторінки без бажаної мови.