- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Uninterruptible power supplies (UPSs)
- User manual
advertisement
HP UPS Network Module
User Guide
Abstract
This document includes installation, configuration, and operation information for the HP UPS Network Module. This document is for the person who installs and maintains power products. HP assumes you are qualified in the servicing of high-voltage equipment and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 637918-002
October 2012
Edition: 2
© Copyright 2011, 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212,
Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license.
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Google™ is a trademark of Google Inc.
Bluetooth® is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
Contents
Contents 3
Contents 4
Contents 5
Overview
Overview
The HP UPS Network Module works with HP Power Protector software to monitor, manage, and protect power environments. The UPS Network Module can send email and text notification messages to configured recipients and alert traps to specified SNMP management programs, such as HP Systems Insight Manager, or used as a stand-alone management system.
NOTE: Text notification on mobile phones require the use of an external provider that converts emails into text notifications on mobile phones.
The HP UPS Network Module includes:
•
HP UPS Network Module web interface (on page 16 )—A graphical interface that is accessed with a
web browser
•
HP UPS Network Module Configuration Menu (on page 48 )—A text-based menu that is accessed
through a terminal emulation session
For a detailed list of supported UPSs, see the HP website ( http://www.hp.com/go/rackandpower ).
Features
The UPS Network Module is a minislot card that requires UPSs equipped with a minislot. The UPS Network
Module:
•
Monitors the status, performs UPS diagnostics, and transmits periodic reports.
•
Manages independent UPS load segments to provide separate power control of connected equipment.
•
Prioritizes the timing of equipment shutdown, and reboots connected equipment by load segment.
•
Delays restart by load segment after a power outage to sequence the startup of system components.
•
Shuts down and reboots the UPS and attached equipment, based on a user-specified schedule.
•
Sends customized email, broadcast, and text notification messages and SNMP traps.
•
Displays logs for analysis.
•
Includes enhanced HP SIM integration.
•
Includes multi-language support.
•
Supports IPv4 and IPv6.
•
Provides automatic date and time adjustment through an NTP server.
•
Supports fast Ethernet 10/100 MB compatibility with auto-negotiation on the RJ-45 network port.
•
Allows for installation while the UPS is online, to maintain the highest system availability.
When used in conjunction with the UPS Network Module, HP Power Protector:
•
Manages an automatic, graceful shutdown of attached equipment during a utility power failure.
Overview 6
•
Issues computer commands at power failure.
•
Supports network-attached server communications.
•
Supports a customizable Events script.
•
Provides redundancy feature support.
•
Is compatible with the R1500 G3 UPS, R/T3000 G2 UPS, R5000 UPS and R7000 UPS.
For more information, see the HP Power Protector User Guide on the HP website
( http://www.hp.com/go/rackandpower ).
HP Power Protector overview
HP Power Protector is a UPS software management application that can be used standalone without the UPS
Network Module in an Administrator/Client configuration or with the UPS Network Module in a Client configuration only.
The HPPP Client runs on a local or network server and allows the UPS Network Module to gracefully shut down the operating system of that server and optionally run a script during power failure. Install the HPPP
Client on any machine that is powered by the UPS and any machine that the UPS Network Module uses to initiate a shutdown command.
For more information, see the HP Power Protector User Guide on the HP website
( http://www.hp.com/go/rackandpower ).
You can also use a third-party SNMP manager to monitor the power protection. For more information, see
"SNMP monitoring (on page 53 )."
Supported hardware configurations
The UPS Network Module can be attached in any of the following configurations:
•
Configuration A (on page 7 )—One or more HPPP Clients are powered by a UPS and communicate with
one UPS Network Module over the network.
•
Configuration B (on page 8 )—One or more HPPP Clients are redundantly powered by two UPSs and
communicate with two UPS Network Modules over the network.
Configuration A
This figure illustrates one or more HPPP Clients are powered by a UPS and communicates with one UPS
Network Module over the network to begin a graceful shutdown in the event of a power failure or other configured shutdown events.
NOTE: Up to 35 HPPP Clients can be managed by one HP UPS Network Module.
Overview 7
4
5
6
Item
1
2
3
Description
UPS with an HP UPS Network Module
HPPP Client server
HPPP Client server
HPPP Client server
Network
Remote workstation browsing into the HP UPS Network
Module or HPPP Client over the network
Power connection
Communication path
Green
Red
Configuration B
This figure illustrates one or more HPPP Clients are redundantly powered by two UPSs and communicate with two UPS Network Modules over the network to begin a graceful shutdown in the event of a power failure or other configured shutdown events.
NOTE: Up to 35 HPPP Clients can be managed by one HP UPS Network Module.
Overview 8
Item
1
2
3
4
5
6
Description
UPS with an HP UPS Network Module
UPS with an HP UPS Network Module
HPPP Client server
HPPP Client server
Network
Remote workstation browsing into the UPS Network
Module or HPPP Client over the network
Power connection
Communication path
Green
Red
Web interface requirements
The following table lists the minimum requirements necessary to operate the UPS Network Module web interface.
Software Browser
Internet Explorer
Mozilla
Firefox
•
Windows Internet Explorer 7
•
Windows Internet Explorer 8
•
Windows Internet Explorer 9
HP-UX Mozilla 1.4.x
•
Linux Firefox 3.5.x (native to Linux version)
•
Windows Firefox 3.6.15
•
Windows Firefox 4
Chrome 10.x
Overview 9
Quick installation and setup overview
1.
2.
3.
4.
5.
Install the UPS Network Module (" Installing the UPS Network Module " on page 12 ) and configure the
network settings.
Access the web interface.
Configure the power fail settings using the Shutdown Parameters screen (on page 35 ).
(optional) Configure additional settings using the menus under Settings (on page 29 ).
Install and configure the HPPP Client on all servers to be protected by the UPS. After all Clients are configured at the servers, they are automatically added by the UPS Network Module and appear on the
Notified Applications screen (on page 42 ).
For more information, see the HP Power Protector User Guide on the HP website
( http://www.hp.com/go/rackandpower ).
Overview 10
Component identification
Front panel connectors and LED indicators
3
4
5
Item
1
2
6
Connector/LED
Network connector
Network Activity LED
Network Speed LED
Settings/AUX connector
UPS Data LED
Configuration Menu LED
Description
Ethernet port
•
Off—UPS Network Module not connected to the network
• Solid green—UPS Network Module connected to the network, but no activity detected
•
Flashing green—UPS Network Module connected to the network and sending or receiving data
•
Off—Port operating at 10 Mb/s
•
Solid orange—Port operating at 100 Mb/s
Configuration port
•
Off—UPS Network Module starting
•
Solid green—UPS Network Module communicating with UPS
• Flashing green—Normal operation (communication link established)
•
Off—Configuration menu activated
•
Solid orange—Normal operation (Configuration menu not activated)
Component identification 11
Installing the HP UPS Network Module
Precautions
See the Important Safety Information guide (included in the UPS kit) before installing this product.
WARNING: A risk of personal injury from electric shock and hazardous energy levels exists. The installation of options and routine maintenance and service of this product must be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with AC power products.
Required tools
No. 2 Phillips screwdriver
Installing the UPS Network Module
NOTE: It is not necessary to power down the UPS before installing the UPS Network Module.
1.
2.
Remove the two screws securing the UPS option slot cover plate and slide the plate out.
Install the UPS Network Module along the alignment channels in the option slot.
Installing the HP UPS Network Module 12
3.
If the UPS is powered up, you can be sure that the UPS Network Module is seated properly and communicating with the UPS by verifying that the UPS Data LED illuminates solid green, and then flashes regularly after 2 minutes.
4.
Secure the UPS Network Module using the two screws you removed in step 1.
Connecting the network cable
Connect a standard Ethernet cable between the network connector on the UPS Network Module and a network jack.
This connection is used to access the UPS Network Module remotely through the web interface. The UPS
Network Module also uses the network connection to communicate to the configured HPPP Clients and to facilitate SNMP-based monitoring.
Installing the HP UPS Network Module 13
Connecting the configuration cable
1.
2.
Connect the DB-9 connector on the DB-9 to RJ-45 cable to a serial connector on the host computer.
Connect the RJ-45 connector on the DB-9 to RJ-45 cable to the Settings/AUX connector on the UPS
Network Module.
This connection is used to access and configure the UPS Network Module network settings locally through a terminal emulation program.
Launching a terminal emulation program
NOTE: HyperTerminal is the serial communication program provided with Microsoft®
Windows® and is used in this section as an example for setting up a terminal emulation session.
If you are using another utility, the steps might be different.
1.
2.
3.
4.
5.
Be sure that the UPS is powered on.
On the host computer, click Start, and select Programs>Accessories>Communications>HyperTerminal.
The Connection Description window appears.
Enter a description, select an icon for the connection, and then click OK. The Connect To window appears.
Select the serial connector on the host computer to which the DB-9 to RJ-45 adapter is attached, and then click OK. The COM Properties window appears.
Select the following parameter values, and then click OK. o o o o o
Bits per second—9600
Data bits—8
Parity—None
Stop bits—1
Flow control—None
Installing the HP UPS Network Module 14
Configuring the UPS Network Module network settings
On the terminal emulation session screen running on the host computer:
1.
Press any key. The initialization process completes, and then you are prompted to enter the password.
2.
At the prompt, enter admin. The HP UPS Network Module Configuration Menu appears.
Use the HP UPS Network Module Configuration Menu to configure the minimum settings required to access the UPS Network Module remotely.
IMPORTANT: The IP address assigned to the UPS Network Module must be fixed. If the IP address changes:
•
The HPPP Client loses communication with the UPS Network Module.
•
You can lose track of the UPS Network Module URL.
3.
If your network is configured with a DHCP server, the network settings are automatically assigned. To view the settings: a. b. c. d. e.
On the Main menu, enter 2 to display the Network Configuration submenu.
Enter 1 to view the network settings.
Record the IP address.
Enter 0 to return to the Main menu.
Enter 0 to exit the Configuration Menu. The UPS Network Module is operational.
NOTE: You can configure the DHCP server to permanently assign the same IP address for each
UPS Network Module using the MAC address of the card.
4.
If your network is not configured with a DHCP server: a. b. c. d. e.
On the Main menu, enter 2 to display the Network Configuration submenu.
Enter 2 to modify the network settings.
Follow the on-screen instructions to enter the static IP parameters. A Done message appears when the parameters are saved.
Enter 0 to return to the Main menu.
Enter 1 to reset the UPS Network Module, and then enter 2 to restart the UPS Network Module with the new IP settings.
Installing the HP UPS Network Module 15
HP UPS Network Module web interface
HP UPS Network Module web interface overview
The web interface graphically displays various measurements and warning and alarm messages from the
UPS Network Module. Also, system values and power fail settings can be configured through the web interface and saved to the UPS Network Module.
NOTE: Network settings included on the UPS Network Module web interface can also be
configured using the HP UPS Network Module Configuration Menu (on page 48 ).
Accessing the web interface
CAUTION: It is highly recommended that browser access to the UPS Network Module is isolated from outside access using a firewall or isolated network.
To access the web interface:
1.
On a network computer, launch a supported browser. The browser window appears.
2.
In the URL field, enter:
3.
4. http://xxx.xxx.xxx.xxx
-or- https://xxx.xxx.xxx.xxx where xxx.xxx.xxx.xxx is the static IP address of the UPS Network Module. The login screen appears.
Enter the user name in the User Name field. The default user name is admin.
Enter the password in the Password field. The default password is admin.
HP UPS Network Module web interface 16
5.
Click Sign In. The HP UPS Network Module web interface appears.
Browser security alert
Secure browsing requires the use of SSL. SSL is a protocol layer that lies between HTTP and TCP that provides secure communication between a server and a client, and is designed to provide privacy and message integrity. SSL is commonly used in web-based transactions to authenticate the web server, which indisputably identifies the server to the browser. SSL also provides an encrypted channel of communication between the server and the browser. The encrypted channel ensures the integrity of the data between the web server and the browser, so that data can neither be viewed nor modified while in transit. The UPS Network Module uses a system generated and unique key.
An integral part of SSL is a security certificate, which identifies the UPS Network Module. If your browser displays a security alert when browsing to the UPS Network Module, it can be for one of several reasons:
•
The certificate is untrusted, meaning it was signed by a certifying authority that is unknown to your browser.
•
The certificate has expired or is not yet valid. This condition can occur if you issue your own certificate and it has expired.
•
The name on the certificate does not match the name of the site in the browser address field.
Establishing a secure session for Internet Explorer
The first time you browse to the UPS Network Module, the Secure Session screen appears. To ensure a secure connection, verify that you are browsing to the desired UPS Network Module:
1.
2.
Click View Certificate.
Verify that the name in the Issued To field is the name of your UPS Network Module.
HP UPS Network Module web interface 17
3.
Perform any other steps necessary to verify the identity of the UPS Network Module.
CAUTION: If you are not sure this is the desired UPS Network Module, do not proceed.
Importing a certificate from an unauthorized source relays your login credentials to that unauthorized source. Exit the certificate window and contact the system administrator.
After verifying the UPS Network Module, do one of the following:
•
Import the certificate and proceed. a.
Click View Certificate. The certificate appears. b. c. d. e. f.
Click Install Certificate. The Certificate Import wizard runs.
Click Next. The Certificate Store screen appears.
Select Automatically select the certificate store based on the type of certificate, and then click Next.
Click Finish. A message appears, asking for verification of the root store.
Click Yes.
•
Proceed without importing the certificate by clicking Yes at the Security Alert window. You continue to receive the Security Alert each time you log in until you import the certificate. Your data is still encrypted.
•
Exit and import the certificate into your browser from a file provided by the administrator. a.
Click No at the Security Alert window. b.
Obtain an exported certificate file from the administrator.
NOTE: If using Internet Explorer, you can manually import the file into the browser by clicking
Tools>Internet Options>Content>Certificates>Import.
Establishing a secure session for Mozilla
The first time you browse to the UPS Network Module, the Secure Session screen appears. To ensure a secure connection, verify that you are browsing to the desired UPS Network Module:
1.
Click Examine Certificate.
2.
3.
4.
Verify that the name in the Issued To field is the name or IP address of your UPS Network Module.
Perform any other steps necessary to verify the identity of the UPS Network Module.
After verifying the UPS Network Module, do one of the following: a. b.
Click either Accept this certificate permanently or Accept this certificate temporarily for this session.
Click OK.
NOTE: If using Mozilla, you can manually import the file into the browser by clicking
Edit>Preferences>Privacy & Security>Certificates>Manage Certificates>Authorities>Import.
Establishing a secure session for Firefox
The first time you browse to the UPS Network Module, the Secure Session screen appears. To ensure a secure connection, verify that you are browsing to the desired UPS Network Module:
1.
Click Examine Certificate.
2.
3.
Verify that the name in the Issued To field is the name or IP address of your UPS Network Module.
Perform any other steps necessary to verify the identity of the UPS Network Module.
HP UPS Network Module web interface 18
4.
After verifying the UPS Network Module, do one of the following: a.
Click either Accept this certificate permanently or Accept this certificate temporarily for this session. b.
Click OK.
NOTE: If using Firefox, you can manually import the file into the browser by clicking
Edit>Preferences>Advanced>Security>View Certificates>Authorities>Import.
Establishing a secure session for Google Chrome
To establish a secure session:
1.
Browse to the UPS Network Module through a secure connection.
2.
The certificate appears with a warning.
Click Proceed anyway, and then login to the UPS Network Module web interface.
Navigating the web interface
The web interface is divided into two frames:
•
Menu tree—Contains a list of menu options on the left side of the screen
•
Main frame—Contains the various interface screens based on the menu option selected in the left navigation frame
Click Help to view online help.
Views
Menu options listed under Views include:
HP UPS Network Module web interface 19
•
Power Source (" Power Source screen " on page 20 )
•
Manual Control (" Manual Control screen " on page 25 )
Power Source screen
Click Power Source in the menu tree to display the Power Source screen. This screen displays the overall status of the UPS. The status information refreshes every 10 seconds.
The top part of the screen displays the following UPS information:
•
UPS status icon—The current UPS status
Status icon Description
Green—Normal operation
Red—Alarm present
Click the icon to display the UPS alarms.
Gray—UPS communication loss
•
UPS name—The name of the UPS
The UPS name is the generic name of the UPS model, and this name displays throughout the interface.
•
UPS location—The location of the UPS
The UPS location can be modified on the System Settings screen (on page 30 ).
•
UPS graphical representation—A graphical representation of the UPS model
•
UPS operating mode diagram—An animated graphical representation of the UPS operating mode showing the main UPS components and the electrical flow powering the load
If communication with the UPS is lost, the diagram appears gray. Diagrams do not display for line-interactive UPSs.
HP UPS Network Module web interface 20
•
UPS measurements—A popup box that displays UPS data details
Hover your mouse over an element in the UPS operating mode diagram to display UPS data details.
UPS data is available for Normal mode, Battery mode, and Bypass mode. The available UPS data depends on the UPS range. Available UPS information includes: o o o o o o
AC Output Voltage—The UPS output voltage
AC Output Current—The UPS output current
AC Output Frequency—The UPS output frequency
Load Level—The percentage of load at the UPS output
Apparent Power—The UPS apparent power
Active Power—The UPS active power
The following table describes the possible UPS operating mode diagrams.
Diagram
UPS operating mode
UPS with automatic bypass
UPS without automatic bypass
The following table describes the possible diagram elements.
Diagram element Description
AC Normal Input
Green—In tolerance
Gray—Out of tolerance
AC Normal Flow
HP UPS Network Module web interface 21
Diagram element
AC to DC Converter
Description
Yellow—AC to DC converter powered by normal AC
Gray—AC to DC converter not powered by normal AC
Green—Powered
Gray—Not powered
Red—Internal failure
Battery
Green—Remaining capacity > 50%
Orange—Remaining capacity < 50%
Battery Output Flow
Red—Battery to be checked (battery test result)
Yellow—AC to DC converter powered by battery
Gray—AC to DC converter not powered by battery
DC to AC Converter Input Flow
Yellow—Energy flow present
DC to AC Converter
DC to AC Converter Output
AC Bypass Input
AC Automatic Bypass Flow
Gray—No energy flow
Green—Powered
Gray—Not powered
Red—Internal failure
Yellow—Energy flow present
Gray—No energy flow
Green—In tolerance
Red—Out of tolerance
HP UPS Network Module web interface 22
Diagram element Description
Yellow—Energy flow present
AC Automatic Bypass Status
Gray—No energy flow
Green—Powered
AC Output Flow
Gray—Not powered
Red—Internal failure
Yellow—Energy flow present
AC Output
Gray—No energy flow
Green—Load protected
Red—Load not protected
The bottom part of the screen displays various tables containing UPS information. The table that displays depends on your selection in the pull-down menu. Available options include:
•
the UPS
•
UPS Alarms (" UPS Alarms table " on page 24 )—Displays a list of current alarms
•
About your UPS (" About your UPS table " on page 24 )—Provides information about the model range
and software version of the UPS and the UPS Network Module
UPS Status table
The UPS Status table displays the following basic information about power and output:
•
Power source—Indicates whether the UPS is on utility power or running on the UPS battery
•
Output load level—The power percentage used at the UPS output
•
Output—Indicates whether the individual UPS outputs are protected o
Entire UPS—Indicates whether the UPS is powered on o
Load segment 1 and Load segment 2—Indicates whether the controlled load segments (if available) are powered
A green outlet icon ( ) indicates that the load segment is on. A red outlet icon ( ) indicates that the load segment is off. A gray outlet icon ( ) indicates that the load segment status is unknown.
•
Battery capacity—The remaining percentage of battery charge and the battery status: o o
Charging—Utility power is present and the battery charge is in progress
Discharging—The UPS is operating on battery power
HP UPS Network Module web interface 23
o
Fault—The battery is faulty
•
Remaining backup time—The estimated maximum battery backup time remaining before UPS shutdown
•
Battery status—The result of the last automatic battery test run by the UPS: o
OK—The test completed correctly. o o o
NOK—The battery needs to be checked.
Deactivated—The automatic battery test was not validated on the UPS.
Aborted—The automatic battery test was not completed on the UPS.
UPS Alarms table
The UPS Alarms table displays a list of current alarms with the following information:
•
Alarm type—The date and time the alarm occurred
•
Alarm description—A description of the alarm
•
Severity—An icon that indicates the severity of the alarm
Icon Alarm severity
Normal
Critical
Warning
Unknown
For a complete list of UPS alarms, see "UPS alarms (on page 68 )."
About your UPS table
The About your UPS table displays the following hardware and firmware information for the UPS and the UPS
Network Module.
•
UPS o o
UPS Name—The name of the UPS
UPS Part Number—The part number for the UPS o o o
UPS Serial Number—The serial number for the UPS
UPS Firmware Revision—The firmware version for the UPS
Communication Board Firmware Revision—The firmware version for the UPS internal communication board
•
UPS Network Module o
Card Firmware Revision—The firmware version for the UPS Network Module o o o o o o
Card Part Number—The model number for the UPS Network Module
Card Technical Level—The technical revision for the UPS Network Module
Card Hardware Revision—The hardware version for the UPS Network Module
Card Serial Number—The serial number for the UPS Network Module
Card Ethernet MAC Address—The MAC address for the UPS Network Module
Card Ethernet Speed—The port speed of the UPS Network Module
HP UPS Network Module web interface 24
Manual Control screen
Click Manual Control in the menu tree to display the Manual Control screen. This screen allows an administrator to execute shutdown and restart sequences for the UPS and its controlled load segments. To prevent data loss, configure the time required to shut down each registered server using the Shutdown
Parameters screen (on page 35 ).
The status of each load segment is indicated by an icon. A green icon ( ) indicates that the load segment is on. A red icon ( ) indicates that the load segment is off. A gray icon ( ) indicates that the load segment status is unknown.
IMPORTANT: The UPS has priority over the controlled load segments. Shutting down the UPS causes the load segments to shut down. Controlled load segments can only be restarted if the UPS is on.
Only users with administrator privileges can save command parameters and execute commands. To configure a command:
1.
Select the command you want to run in the Control pull-down menu. Configured commands will not initiate until you click Execute. o
Safe power down—A shutdown sequence for the load segment is launched immediately.
Connected equipment powers off, and then the load segment powers off. o o
Safe power down & reboot—A sequence containing a shutdown command followed by a restart command for the load segment is launched immediately. Connected equipment powers off, and then the load segment powers off. The load segment restarts when the Toggle Duration time is reached.
Immediate On—A restart sequence for the load segment is launched immediately. The load segment powers on, and then connected equipment powers on.
HP UPS Network Module web interface 25
2.
3.
4.
5.
6. o o
Delayed, safe power down—A shutdown sequence for the load segment is launched when the Off
Delay time is reached. Connected equipment powers off, and then the load segment powers off.
Delayed, safe power down & reboot—A sequence containing a shutdown command followed by a restart command for the load segment is launched when the Off Delay time is reached. Connected equipment powers off, and then the load segment powers off. The load segment restarts when the
Toggle Duration time is reached. o
Delayed On—A restart sequence for the load segment is launched when the On Delay is reached.
The load segment powers on, and then connected equipment powers on.
Configure the Off Delay time for delayed power down commands. Enter the number of seconds that should elapse between the time you execute the command and the shutdown sequence initiates.
Configure the Toggle Delay time for power down & restart commands. Enter the number of seconds that should elapse between the time the shutdown sequence completes and the restart sequence initiates.
Configure the On Delay time for power on commands. Enter the number of seconds that should elapse between the time you execute the command and the restart sequence initiates.
Click Save to save the Off Delay, Toggle Delay, and On Delay parameters.
Click Execute to initiate the configured commands.
Click Help to view online help.
Logs
Menu options listed under Logs include:
•
UPS Data Log (" UPS Data Log screen " on page 26 )
•
Event Log (" Event Log screen " on page 28 )
•
System Log (" System Log screen " on page 29 )
UPS Data Log screen
Click UPS Data Log in the menu tree to display the UPS Data Log screen. This screen displays a log of UPS data collected by the UPS Network Module. The frequency at which data is collected can be modified on the
System Settings screen (on page 30 ). By default, data is collected every 60 seconds.
NOTE: In the UPS Data Log and the Event Log, the date and time stamps are converted to the local time zone.
HP UPS Network Module web interface 26
The following information is displayed for a single phase UPS:
•
AC Input Voltage—The utility voltage supplying the UPS
•
AC Input Frequency—The utility frequency supplying the UPS
•
AC Output Voltage—The UPS output voltage
•
AC Output Frequency—The UPS output frequency
•
AC Output Power (kVA)—The UPS output power
•
AC Output Load level (%)—The percentage of load at the UPS output
•
Battery Capacity (%)—The percentage of battery charge available
•
Battery Remaining time (min)—The estimated remaining backup time
NOTE: When the log reaches the maximum of 435 entries, new entries overwrite the oldest entries in the log.
On the screen:
•
Click Save Log to download the log file (.csv) to your computer.
•
Click Clear Log to clear the log files. Only users with administrator privileges can clear logs.
•
Click Help to view online help.
HP UPS Network Module web interface 27
Event Log screen
Click Event Log in the menu tree to display the Event Log screen. This screen displays a log of the events that have occurred on the UPS, such as the UPS switching to battery power.
NOTE: In the UPS Data Log and the Event Log, the date and time stamps are converted to the local time zone.
The following information is displayed for each event:
•
Date—The date at which the event occurred
•
Time—The time at which the event occurred
•
Event Description—A description of the event
NOTE: When the log reaches the maximum of 435 entries, new entries overwrite the oldest entries in the log.
On the screen:
•
Click Save Log to download the log file (.csv) to your computer.
•
Click Clear Log to clear the log files. Only users with administrator privileges can clear logs.
•
Click Help to view online help.
HP UPS Network Module web interface 28
System Log screen
Click System Log in the menu tree to display the System Log screen. This screen displays a log of the events that have occurred on the UPS Network Module, such as a communication failure or system shutdown.
The following information is displayed for each event:
•
Date—The date at which the event occurred
•
Time—The time at which the event occurred
•
Event Description—A description of the event
NOTE: When the log reaches the maximum of 435 entries, new entries overwrite the oldest entries in the log.
On the screen:
•
Click Save Log to download the log file (.csv) to your computer.
•
Click Clear Log to clear the log files. Only users with administrator privileges can clear logs.
•
Click Help to view online help.
Settings
Menu options listed under Settings include:
•
System Settings (" System Settings screen " on page 30 )
•
Access Control (" Access Control screen " on page 31 )
•
Network Settings (" Network Settings screen " on page 32 )
•
Time Settings (" Time Settings screen " on page 34 )
•
Shutdown Parameters (" Shutdown Parameters screen " on page 35 )
•
Scheduled Shutdown (" Scheduled Shutdown screen " on page 39 )
•
SNMP Settings (" SNMP Settings screen " on page 41 )
HP UPS Network Module web interface 29
•
Notified Applications (" Notified Applications screen " on page 42 )
•
Email Notification (" Email Notification screen " on page 44 )
•
Firmware Upload (" Firmware Upload screen " on page 47 )
System Settings screen
Click System in the menu tree to display the System Settings screen. This screen allows an administrator to enter contact information, reset communication, and restore factory default settings on the UPS Network
Module.
To enter the system information:
1.
2.
Enter the name of the person responsible for UPS administration in the UPS Contact field. This text field is limited to 49 characters.
Enter a description of the physical location of the UPS in the UPS Location field. This text field is limited to 31 characters. The UPS Location displays throughout the interface.
3.
4.
5.
6.
Enter a custom name for the UPS in the System Name field. This name appears throughout the interface and is included in SNMP traps. Use a unique name for each UPS.
Select the display language of the web interface in the Default Language pull-down menu. Available options are English, Japanese, or Auto. Select Auto to allow the interface to display the language configured for the web browser. Refresh the browser window for changes to take effect.
Enter the time interval for UPS data collection in the History log interval (sec) field. The interval can be between 5 and 99999 seconds. By default, UPS data is collected every 60 seconds.
Click Save.
To perform a remote reboot of the UPS Network Module without modifying the configuration, click Reset
Communication. This action is required to enable any changes made on the Network Settings screen (on
To restore all UPS Network Module parameters to the default configuration, click Factory Reset. The UPS
Network Module communication will be lost. To maintain communication, select the Keep TCP/IP parameters checkbox, and then click Factory Reset. The configured IP address, subnet mask, gateway, and
BOOTP/DHCP parameters are not reset.
HP UPS Network Module web interface 30
Click Help to view online help.
For a summary of the default configuration, see "Default parameters (on page 76 )."
Access Control screen
Click Access Control in the menu tree to display the Access Control screen. This screen allows three administrator accounts to configure secure access to the UPS Network Module through a web browser. Enter the first administrator account login username and password in HPPP Clients > Device Discovery > Configure
Power Source to access HP UPS Network Module. The second and third accounts can be enabled or disabled by the administrator.
To configure the administrator account that provides secure access and enables modification of configuration settings and log files:
1.
Enter a new user name in the Enter New Manager Login field, and then enter a new password in the
Enter New Password field.
2.
Each field requires a minimum of five characters and is limited to a maximum of 31 characters. The default user name and password for the first administrator account is admin.
Re-enter the new password in the Confirm New Password field.
3.
Select the authentication method for the security mode. o o
Authentication for configuration—Configuration screens are protected by a user name and password.
Full authentication—All pages are protected by a user name and password.
HP UPS Network Module web interface 31
4. o
SSL and full authentication—All pages are protected by a user name and password, and are only accessible in SSL. Access to the web interface occurs through HTTPS. The connections to the UPS
Network Module remain in standard mode (secure TCP).
Click Save.
Click Help to view online help.
Network Settings screen
Click Network in the menu tree to display the Network Settings screen. This screen allows an administrator to configure network settings and authorize remote firmware upgrades for the UPS Network Module.
To configure the network settings:
1.
Select Enabled from the BootP/DHCP pull-down menu to allow configuration of network parameters by a BootP or DHCP server. After each restart, the UPS Network Module makes five attempts to recover the network parameters. If a response is not received from the server, the UPS Network Module boots with the last saved parameters from the most recent start.
2.
If your network is not configured with a BootP or DHCP server, select Disabled from the BootP/DHCP pull-down menu, and then enter the network settings: a.
Enter the IP address of the UPS Network Module in the IP Address field. The UPS Network Module must have a unique IP address for use on a TCP/IP network. b.
Enter the subnet mask of the UPS Network Module in the Subnet Mask field to identify the class of the sub-network to which the UPS Network Module is connected.
HP UPS Network Module web interface 32
3.
4.
5.
6.
7.
8.
9. c. d.
Enter the gateway address of the UPS Network Module in the Gateway Address field to allow connection to devices or hosts attached to different network segments.
Enter the host name of the UPS Network Module in the Hostname field. The host name is the first part of the fully qualified domain name used by the DNS. The host name is sent to the DNS only if the
DHCP server sends the host name with the new IP address. The default value of the two parameters comprising the fully qualified domain name is ups.domain.com. e.
Enter the name of the domain to which the UPS Network Module belongs in the Domain Name field.
The domain name is the part of the fully qualified domain name that follows the host name and is used by the DNS. The default value of the two parameters comprising the fully qualified domain name is ups.domain.com.
Select or clear the IPv6 Enabled checkbox to enable or disable IPv6, respectively. The local IP address of the UPS Network Module is built from the MAC address and appears in the IPv6 Local Address field when IPv6 is enabled.
If IPv6 is enabled, select the IPv6 Auto Config Enabled checkbox to have the IPv6 router build the IPv6
Address 1, Prefix length, and IPv6 Address 2. The IPv6 Gateway field is empty and cannot be edited.
-or-
Clear the IPv6 Auto Config Enabled checkbox and enter the following settings: o o
IPv6 Address 1—Set a static IPv6 address.
Prefix length—Set a prefix for the IPv6 Address 1. o
IPv6 Gateway—Set the default gateway.
Select Enabled from the Firmware Upload to allow remote upgrade of the UPS Network Module firmware through the network. If this option is disabled, remote firmware upgrade is not allowed.
Enter the IP address of the DNS server that normally provides the translation of the domain name to IP address in the Primary DNS Server field.
Enter the IP address of the secondary DNS server that provides the translation of the domain name to IP address when the primary DNS server is not available in the Secondary DNS Server field.
Enter the host name or IP address of the SMTP server used to transfer email messages in the SMTP Server field.
Select the SMTP server authentication checkbox to require a user name and a password for SNMP authentication. Enter the user name in the Login field, and then enter the password in the Password field.
NOTE: The UPS Network Module will not send email notifications until the recipients are
configured on the Email Notification screen (on page 44 ).
10.
11.
Click Save.
For your changes to take effect, be sure to reboot the UPS Network Module by clicking Reset
Communication on the System Settings screen (on page 30 ).
Click Help to view online help.
HP UPS Network Module web interface 33
Time Settings screen
Click Date and Time in the menu tree to display the Time Settings screen. This screen allows an administrator to set the UPS Network Module date and time.
The current date and time appears at the top of the screen.
To manually enter the date and time:
1.
Select the Set manually radio button.
2.
3.
4.
Enter the date (yyyy/mm/dd) in the Date field.
Enter the time (hh:mm:ss) in the Time field.
Click Save.
After the system reboots, it needs to sync with the UPS date and time on UPSs with real time clock. Otherwise the default date is set to 1970/01/01 and the default time is set to 00:00:00. To avoid this, select either the
Accept Automatic Update from HPPP radio button (default setting) or the Synchronize with NTP Server radio button.
To synchronize the date and time with the HPPP Client:
NOTE: Verify that the HPPP Client is configured with the correct date and time, because the UPS
Network Module uses the time from the first Client that responds.
1.
2.
Select the Accept automatic update from HP Power Protector radio button.
Click Save.
To synchronize the date time with an NTP server:
1.
Select the Synchronize with NTP server radio button. If no NTP server is discovered, the date is set to
1970/01/01 and the time is set to 00:00:00.
HP UPS Network Module web interface 34
2.
3.
4.
5.
Enter the IP address or host name of the NTP server in the Hostname field.
Select the time zone for your geographic area from the Time-Zone pull-down menu.
Select the Disable radio button if daylight saving time should not be reflected in the time on the UPS
Network Module.
-or-
Select the Enable radio button to configure time adjustment for daylight saving time: a. b. c.
Select the week number, day, month, and time for which daylight saving time should start. For example, if daylight saving time starts the second Sunday of March at 2:00 am, select Second,
Sunday, and March, and then enter 02:00.
Select the week number, day, month, and time for which daylight saving time should end. For example, if daylight saving time ends the first Sunday of November at 3:00 am, select First,
Sunday, and November, and then enter 03:00.
Select the amount of time the clock should change for daylight saving time in your region. Available options are 30 minutes and 1 hour.
Click Save to connect to the NTP server and set the date and time.
The UPS Network Module uses the NTP protocol (UDP 123 port). The firewall must be set to transmit queries outside the network. No error message is generated if connection with the NTP server fails. The
UPS Network Module attempts to connect to the NTP server every 10 seconds until a connection is made.
Click Help to view online help.
Shutdown Parameters screen
Click Shutdown Parameters in the menu tree to display the Shutdown Parameters screen. This screen allows an administrator to configure how the UPS Network Module should shut down and restart the UPS and attached devices in the event of a power failure.
HP UPS Network Module web interface 35
The Shutdown Parameters table contains a row for the entire UPS and a row for each load segment. Settings for the entire UPS apply to all load segments. Settings for individual load segments only apply to that load segment.
To configure the shutdown parameters:
1.
Configure shut down and restart: a.
Enter the On Battery values. When a utility power failure occurs, the UPS automatically switches to battery power. One or all of the values in this column are set to allow protected servers to be powered by a UPS operating on battery power. In the event of a utility power failure, all On Battery settings are evaluated, and the first trigger that is reached initiates the shutdown sequence. i.
In the Shutdown initiated if remaining backup time under field (entire UPS), enter the minimum amount of battery life that can remain before the UPS shutdown sequence starts (0 to 99999 seconds, 180 seconds by default). The UPS Network Module initiates a UPS shutdown when the remaining battery life reaches the specified time.
HP UPS Network Module web interface 36
Item
7
8
5
6
9
1
2
3
4
Description
Battery capacity
Time
Utility failure
Shutdown initiated
Load segment powered down
Low battery
Battery depleted
Operating system shutdown time
Remaining backup time under ii.
In the Shutdown initiated after field (individual load segments), enter the number of seconds after the power fails that the UPS Network Module should wait before starting to shut down the load segment (0 to 99999 seconds, 300 seconds by default). Enter a shorter delay for load segments that power less critical equipment to preserve UPS battery power for other load segments. The value you enter is continually compared with the maximum Shutdown initiated after shutdown time of all subscribed HP Power Protector — Clients. The highest value is automatically used.
Item
7
8
9
5
6
3
4
1
2
Description
Battery capacity
Time
Utility failure
Shutdown initiated
Load segment powered down
Low battery
Battery depleted
Operating system shutdown time
Shutdown initiated after time iii.
In the Shutdown initiated if battery capacity under field (individual load segments), enter the minimum amount of battery life that can remain before the load segment shutdown sequence
HP UPS Network Module web interface 37
starts (0 to 100%, 20% by default). The UPS Network Module initiates a load segment shutdown when the remaining battery life reaches the specified percentage.
8
9
Item
5
6
7
3
4
1
2
NOTE:
Description
Battery capacity
Time
Utility failure
Shutdown initiated
Load segment powered down
Low battery
Battery depleted
Operating system shutdown time
Shutdown initiated after time
This parameter can initiate the shutdown sequence before the shutdown delay expires. b.
Enter the OS Shutdown value for protected servers connected to the individual load segments (0 to
99999 seconds, 120 seconds by default). This is the number of seconds required to completely shut down protected servers, including running shutdown scripts, shutting down the operating systems, and powering off the servers. The value you enter is continually compared with the maximum OS shutdown time of all subscribed HP Power Protector — Clients. The highest OS Shutdown value is automatically used.
NOTE: When one of the On Battery triggers is reached, the shutdown sequence starts for that load segment or for the entire UPS. When the OS Shutdown timer is started, the shut down cannot be reversed, even if utility power is restored. c.
Enter the Restart values. When utility power is restored, all Restart settings are evaluated, and the first trigger that is reached initiates the restart sequence.
IMPORTANT: Carefully plan the restart settings configuration. You might experience an additional delay before servers power up, even though utility power is restored.
HP UPS Network Module web interface 38
2. i. ii.
In the Restart if battery capacity exceeds field (entire UPS), enter the percentage of battery charge that must be available before restarting the UPS after AC power is restored (0 to 100%,
0% by default).
In the Switch on after the restart (individual load segments), enter the number of seconds after the
UPS restarts that the UPS Network Module should wait before restarting the load segment (from
0 to 99999 seconds, 30 seconds by default). This option allows utility power to stabilize and disks in shared storage configurations to spin up before the server restarts.
Click Save.
For more information about shutdown parameters, see "Shutdown parameters (on page 54 )."
Click Help to view online help.
Scheduled Shutdown screen
For a valid schedule, be sure the time is set correctly on the Time Settings screen (on page 34 ).
While configuring scheduled shutdowns, be sure to adhere to the following rules:
•
The Restart Date/Time must be after the Shutdown Date/Time. If an Every Day shutdown frequency is selected, the Restart Date/Time can be the day after the Shutdown Date/Time, but must be before the next scheduled shutdown.
•
When scheduling Daily and Weekly shutdown times, verify that the Shutdown Date/Time or the Restart
Date/Time do not overlap.
To configure scheduled shutdowns:
1.
Click Scheduled Shutdowns. The List of Scheduled Shutdowns screen appears.
2.
Do one of the following: o
Click Add Scheduled Shutdowns to add a new scheduled shutdown. The Add a New Scheduled
Shutdown screen appears. o
In the Selected column, select a scheduled shutdown that you want to configure, and then click Edit
Scheduled Shutdown. The Edit an Existing Scheduled Shutdown Settings screen appears.
HP UPS Network Module web interface 39
3.
4.
5.
6.
7. o
In the Selected column, select a scheduled shutdown that you want to remove, and then click Delete
Scheduled Shutdown.
In the Status field, select Enabled to activate the scheduled shutdown or select Disabled to disable the scheduled shutdown.
In the Schedule Frequency field, select One Time, Every Day, or Every Week to set the occurrence of the scheduled shutdown.
In the Shutdown (Date/Time) field: a. b. a. b.
Enter a date for the scheduled shutdown to begin in the format yyyy/mm/dd or choose a date from the calendar.
Select the hour for the scheduled shutdown to begin. c.
Select the minute for the scheduled shutdown to begin.
In the Restart (Date/Time) field:
Enter a date for the scheduled restart in the format yyyy/mm/dd or choose a date from the calendar.
Select the hour for the scheduled shutdown to restart. c.
Select the minute for the scheduled shutdown to restart.
Click Save. A warning message appears if scheduled shutdowns conflict, or if there is more than seven days between shutdown and restart of an Every Week periodicity.
Click Cancel to go back to the previous screen.
Click Help to view online help.
HP UPS Network Module web interface 40
SNMP Settings screen
Click SNMP in the menu tree to display the SNMP Settings screen. This screen allows an administrator to configure SNMP settings for computers that use the HP Power MIB to request information from the UPS
Network Module.
To configure the SNMP settings:
1.
Select the SNMP version supported by the UPS Network Module from the Version pull-down menu.
Available options are Disabled, V1, V3, and V1 and V3.
2.
3.
Configure the SNMP V1 settings: a.
Enter the SNMP Community Read-Only string. The UPS Network Module and the Clients must share the same community name to communicate. b. c.
Select or clear the SNMP Write Enabled checkbox to enable or disable the SNMP write function.
If the SNMP write function is enabled, enter the SNMP Community Write string. The UPS Network
Module and the Clients must share the same community name to communicate.
Configure the SNMP V3 settings: a. b.
Enter a user name for the Read-Only User. This user is only authorized to read SNMP variables.
Select a level of security from the Read-Only Security Level pull-down menu: c. d.
—
No Auth No Priv—The user does not use authentication and privacy to access SNMP variables.
—
Auth No Priv—The user must use authentication, but not privacy, to access SNMP variables.
—
Auth Priv—The user must use authentication and privacy to access SNMP variables.
Enter the Read-Only Password to specify a new password for the Read-Only User. The password can be between 8 and 24 alphanumeric characters and the <>&@#%_=:;,./?|$*() symbols.
Enter a user name for the Read-Write User. This user is authorized to read and write SNMP variables.
HP UPS Network Module web interface 41
4. e.
Select a level of security from the Read-Write Security Level pull-down menu:
—
No Auth No Priv—The user does not use authentication and privacy to access SNMP variables.
—
Auth No Priv—The user must use authentication, but not privacy, to access SNMP variables. f. g.
—
Auth Priv—The user must use authentication and privacy to access SNMP variables.
Enter the Read-Write Password to specify a new password for the Read-Write User. The password can be between 8 and 24 alphanumeric characters and the <>&@#%_=:;,./?|$*() symbols.
Enter a user name to include in SNMPV3 notification in the Notification Username field. This field must also be defined in the applications that receive the notifications. The user name can be between 8 and 24 alphanumeric characters and the <>&@#%_=:;,./?|$*() symbols.
Click Save.
Click Help to view online help.
Notified Applications screen
Click Notified Applications in the menu tree to display the Notified Applications screen. This screen allows an administrator to manage trap receivers and HPPP Clients installed on protected servers. You can add trap receivers using this screen, but all HPPP Clients are configured at the servers, and are automatically added by the UPS Network Module.
NOTE: To query SNMP data, you do not need to add SNMP Manager.
The following information is available on the Notified Applications screen:
•
Nr—The assigned application number in the Notified Applications list
•
Hostname or IP Address—The host name or IP address of the server running the application
The host name of the computer displays when the IP address can be converted into a host name by a
DNS server, or if the application has been entered using the server host name.
•
Application Name—The name assigned to the application on the Trap Receivers Settings screen (on
HP UPS Network Module web interface 42
Applications appear in the order in which they subscribe to the UPS Network Module. SNMP management applications, such as HP Systems Insight Manager, can receive notifications from the UPS
Network Module.
•
Output—The name of the UPS load segment from which the Client is powered
•
Shutdown after (min)—The time available to the user after a utility power failure occurs and before the
UPS shutdown sequence initiates
This value is configured in the HPPP Client and displays in this column.
•
OS Shutdown time (sec)—The time required to completely shut down the operating system
This value is configured in the HPPP Client and displays in this column.
•
Link—A hyperlinked icon to the web interface for the notified application
•
( HTTP Connection, HTTPS Connection, or Communication Loss)
To add a trap receiver:
1.
Click Add Trap Receiver.
2.
Configure the settings for the new application on the Trap Receivers Settings screen (on page 43 ).
To modify a trap receiver:
1.
Select the checkbox for the application you want to modify. To select all applications, click All.
2.
3.
Click Modify Trap Receiver.
Modify the settings for the application on the Trap Receivers Settings screen (on page 43 ).
To remove a trap receiver:
1.
Select the checkbox for the application you want to remove. To select all applications, click All.
2.
Click Remove.
To simulate a utility power failure:
1.
Select the checkbox for the application you want to test. To select all applications, click All.
2.
3.
Click Utility Failure Test. The UPS Network Module sends a Utility failure trap, and then sends a Utility restored trap 30 seconds later.
Verify that the selected application received the traps over the network.
To simulate a UPS On Battery condition:
1.
Select the checkbox for the application you want to test. To select all applications, click All.
2.
3.
Click Shutdown Test.
The selected application processes the simultaneous alarms and performs an actual shutdown sequence.
CAUTION: The Shutdown Test generates an actual shutdown sequence for the server on which the application is running.
4.
Verify that the server protection is working correctly.
Click Help to view online help.
Trap Receivers Settings screen
Click Add Trap Receiver on the Notified Applications screen to display the Trap Receivers Settings screen.
This screen allows an administrator to configure management applications to receive SNMP traps from the
HP UPS Network Module web interface 43
UPS Network Module. SNMP management applications, such as HP Systems Insight Manager, can receive notifications from the UPS Network Module.
Up to three applications can be configured to receive SNMP traps from the UPS Network Module. To configure an application to receive SNMP traps:
1.
Enter the name of the application in the Application Name field. HP recommends adding “SNMP” or
“Trap” to the name to for easy monitoring.
2.
3.
Enter the host name or the IP address of the management server on which the application is running in the Hostname or IP address field.
Select the SNMP version from the Protocol pull-down menu.
4.
5.
6.
If you selected SNMP V1, enter the community string in the Trap Community field.
Select the checkbox for the appropriate MIB: o
HP MIB (cpqpower.mib)—The HP Power MIB o
IETF MIB (RFC1628)—A standard UPS MIB
Click Save. The application information appears on the Notified Applications screen (on page 42 ).
Click Help to view online help.
Email Notification screen
Click Email Notification in the menu tree to display the Email Notification screen. This screen allows an administrator to configure recipients of email notifications from the UPS Network Module. Before email
HP UPS Network Module web interface 44
The email messages sent by the UPS Network Module are compatible with mobile transfer telephone systems using the SMS standard for text messaging. The required format might vary, depending on the cellular service provider. Contact your cellular service provider for mail to SMS gateway settings.
Up to four recipients can be configured to receive email notifications from the UPS Network Module. To configure a recipient of email notifications:
1.
Enter the email address of the recipient in the Recipient field.
2.
3.
Select the appropriate checkboxes to add log file attachments to the email notifications for the recipient.
The selected log files are included in .csv format.
To send periodic email reports with log file attachments to the recipient: a. b. c.
Enter the interval in days between email report transmissions.
Select the time of the day when email reports are generated and transmitted from the pull-down menu.
Select the date of the month the next email report should be generated and transmitted.
After this date, the screen indicates the date and time of the next transmission. Log files are included in .csv format.
4.
5.
6.
Select the checkbox for each event that should trigger an email notification to the recipient. To save the notified event configuration to the default selections, click Set Default. The default selections are: o
UPS Off sequence in progress o
UPS alarms
Click Save.
Click Test to send a test email notification to the recipient.
To disable a recipient email address:
1.
Select the address for the recipient you want to disable.
HP UPS Network Module web interface 45
2.
3.
Select Disabled from the Recipient pull-down menu.
Click Save.
To configure the format of email notifications:
1.
2.
Click Email Message Settings.
Configure the email format for all recipients on the Email Message Settings screen (on page 46 ).
To configure the SMTP server:
1.
Click Network Settings.
2.
Configure the SMTP server settings on the Network Settings screen (on page 32 ).
Click Help to view online help.
Email Message Settings screen
Click Email Message Settings on the Email Notification screen to display the Email Message Settings screen.
This screen allows an administrator to customize the format of email messages initiated by the UPS Network
Module. The email message format applies to all recipients.
To customize email messages:
1.
Enter the address for the source of email messages in the Sender field. The sender address can contain up to 59 characters. The default value is [email protected]. Depending on your SMTP server configuration, an existing domain might be required, with the user belonging to that domain.
2.
Enter text you want to include in the email message subject lines in the Subject field. Select from the optional checkboxes to build the message subject: o
UPS name—Includes the name of the UPS in the email subject when selected o o
UPS location—Includes the geographic location of the UPS in the email subject when selected
Event message—Identifies the event generating the message in the email subject when selected
HP UPS Network Module web interface 46
3.
Enter text you want to include in the email message body in the Message field: A maximum of 255 characters is allowed.
The body of the email message contains: o o o
Duplication of the subject, if configured.
The date and time of the event, as saved in the log.
A URL hyperlink to the UPS Network Module o o
Attachments for the email recipient, as configured on the Email Notification screen (on page 44 ).
The message text you entered in the Message field.
Click Save.
4.
The email messages sent by the UPS Network Module are compatible with mobile transfer telephone systems using the SMS standard for text messaging. The required format might vary, depending on the cellular service provider. Contact your cellular service provider for mail to SMS gateway settings.
Click Help to view online help.
Firmware Upload screen
Click Firmware Upload in the menu tree to display the Firmware Upload screen. This screen allows an administrator to upgrade the UPS Network Module firmware.
During the upgrade process, the UPS Network Module does not monitor the UPS status. To upgrade the firmware:
1.
Download the latest firmware version from the HP website ( http://www.hp.com/go/rackandpower ).
2.
3.
4.
Click Browse.
Navigate to the folder where you saved the downloaded firmware.
Click Upload. The upload can take up to 5 minutes. Do not close the web browser or interrupt the operation. A confirmation message displays when the firmware upload successfully completes, and the
UPS Network Module automatically restarts.
Click Help to view online help.
HP UPS Network Module web interface 47
HP UPS Network Module Configuration Menu
HP UPS Network Module Configuration Menu overview
The HP UPS Network Module Configuration Menu provides an alternative, limited interface to the UPS
Network Module. System network values can be configured through the Configuration Menu and saved to the UPS Network Module.
NOTE: All parameters included in the UPS Network Module Configuration Menu can also be
configured using the HP UPS Network Module web interface (on page 16 ).
Accessing the Service Menu
On the terminal emulation session screen running on the host computer:
1.
Press any key. The initialization process completes, and you are prompted to enter the password.
2.
At the prompt, enter admin. The HP UPS Network Module Configuration Menu appears.
Navigating the menus
After you have successfully initiated a terminal emulation session, the UPS Network Module Configuration
Menu appears.
•
Open a submenu by entering the corresponding option number at the prompt.
•
To enter or change configuration information, follow the on-screen prompts.
•
Enter 0 at the submenu prompt to go to the previous menu.
-or-
Enter 0 at the Main menu prompt to exit the utility.
•
Press the Enter key to refresh the screen.
•
You must restart the UPS Network Module to allow configuration changes to take effect.
Main menu
This menu only appears when accessing the UPS Network Module using a terminal emulation program.
Option number Submenu Description
1
Reset Resets the UPS Network Module
HP UPS Network Module Configuration Menu 48
Option number
2
3
4
0
Submenu Description
Network Configuration Enables network configuration for the UPS
Network Module
Set Login Password to Default Restores the login password to the default password
Return to Default Configuration Restores all settings to the default parameters
Exit Exits the Configuration Menu
0
Reset submenu
Option number
1
Submenu
Hardware Reset
2
0
Restart Application
Exit
Network Configuration submenu
Option number
1
Submenu
Read Network Settings
2
Modify Network Settings
3
Set Ethernet Speed
Exit
Description
Restarts the electrical power supply for the UPS
Network Module
Restarts the UPS Network Module application
Returns to the previous menu
Description
Enables you to view IPv4 and IPv6 network settings for the UPS Network Module
Enables you to change IPv4 network settings for the UPS Network Module
Enables you to configure the port speed for the
RJ-45 Ethernet network connector
Returns to the previous menu
HP UPS Network Module Configuration Menu 49
Systems Insight Manager integration
Systems Insight Manager overview
Use HP Systems Insight Manager to:
•
Discover the UPS Network Module. As part of the discovery process, HP SIM can detect an installed
UPS Network Module. The web interface for the discovered module can be launched from the HP SIM
All Systems page.
•
Receive SNMP traps from the UPS Network Module. The module can send event-based traps to HP SIM that include a URL in the trap. This functionality enables administrators to easily launch the web interface of the module in context. For example, if the UPS Network Module detects an alarm condition, the module can send a trap to HP SIM with an attached hyperlink that routes users directly to the web interface for the attached UPS.
•
Conveniently launch the UPS Network Module web interface from within HP SIM. o
All Systems page—All discovered UPS Network Modules appear on the All Systems page. Click the link in the System Name column to launch a browser session.
Systems Insight Manager integration 50
o
Event-based trap—A URL is included in each trap to link directly from HP SIM to the Overview screen for the specific device for which the trap was sent.
Discovering the UPS Network Module
HP SIM automatically detects UPS Network Modules as part of the device discovery process. If detected, a hyperlink is included on the HP SIM All Systems page for the UPS on which the UPS Network Module is installed. The UPS Network Module should be installed and running before attempting discovery through HP
SIM.
If the defaults are not used, a new entry can be made to the additionalwsdisc.props file, located in the
CONFIG directory in the HP SIM install directory, to allow HP SIM to correctly discover and identify the UPS
Network Module. For more information on editing the additionalwsdisc.props file, see the additionalwsdisc.txt file located in the same directory.
Example: ADDITIONALWSDISC.PROPS file with UPS Network Module entry
# ----------------------------------------------------
# Additional Web Server Discovery Properties
#
# ----------------------------------------------------
# NOTE: See "additionalWsDisc_README.txt" for a description of entries in
# this file and how to add or remove additional web server ports used for
# discovery and identification.
# ----------------------------------------------------
#
# ----------------------------------------------------
# The following are actual web server ports enabled by default.
# To remove them from the discovery process, comment out the line with a '#'
# or remove it. You will need to restart the HP SIM service for
# the changes to take effect. In addition you will need to run the Device
# Identification task to find any new ports that were defined.
# ----------------------------------------------------
411=Director Agent, ,true,false, ,http
3201=Compaq TaskSmart, ,true,false, ,https
8008=Default Home Page, ,true,false, ,http
1311=Server Administrator, ,true,false, ,https
1234=HP UPS Network Module, ,true,false, ,https
The last entry allows HP SIM to detect a UPS Network Module running on port 1234 and using HTTPS
(Secure Socket Layer protocol).
HP SIM services must be restarted to apply the change.
Systems Insight Manager integration 51
Configuring HP SIM to receive traps
Before HP SIM can receive traps, the correct MIB file (cpqpower.mib) must be compiled into HP SIM. To download the HP Power MIB, visit the HP website ( http://www.hp.com/go/rackandpower ).
To register the MIB:
1.
Copy the MIB to the HP\Systems Insight Manager\mibs folder.
2.
3.
4.
From the HP\Systems Insight Manager\mibs folder, run mcompile cpqpower.mib from the command line to compile the new MIB. A new file named cpqpower.cfg is created.
Register the new MIB by entering mxmib -a cpqpower.cfg from the HP\Systems Insight
Manager\mibs command line.
Enter HP\Systems Insight Manager\mibs>mxmib at the command line and verify that the new
MIB is listed.
NOTE: For more information on uploading and registering a MIB in HP SIM, refer to the HP
Systems Insight Manager Technical Reference Guide located on the HP Management CD.
Configuring the UPS Network Module to send traps to
HP SIM
configured server appears on the Notified Applications screen (on page 42 ).
Systems Insight Manager integration 52
Optional power monitoring using SNMP
SNMP monitoring
Battery status, power status, events, and traps can be monitored using third-party SNMP managers. SNMP monitoring supports the RFC-1628 MIB and the HP Power MIB (CPQPOWER.MIB).
To query SNMP data, you do not need to add SNMP Mangers to the Notified Application page.
In the third-party SNMP manager, configure the IP address of the UPS Network Module, select SNMP V1 or
V1&V3, and then compile either CPQPOWER.MIB or UPS.MIB (RFC1628) to be monitored by the SNMP manager.
The HP Power MIB (CPQPOWER.MIB) can be downloaded from the HP website
( http://www.hp.com/go/rackandpower ).
Optional power monitoring using SNMP 53
Configuration parameters
Shutdown parameters
Follow these shutdown principles when configuring the shutdown parameters:
•
The Shutdown initiated after (SIA) value entered for the UPS Network Module must be equal to or greater than the HPPP Client configured with the longest SIA time. Otherwise, the Client starts to shutdown at the same time as the UPS Network Module.
•
The Operating system shutdown time (OST) value entered for the UPS Network Module must be equal to or greater than the HPPP Client configured with the longest OST. Otherwise, it is automatically replaced by the longest OST when the Client is connected. The updated value is displayed on the
Shutdown Parameters screen for the UPS Network Module.
•
After the operating system shutdown begins, the shutdown process cannot be canceled, even if utility power is restored.
•
For load shedding, each Client is shutdown based on its own delay settings. This increases the backup time for the remaining Clients.
•
The UPS Network Module waits until the operating system is shut down before powering down the load segments.
•
The UPS is powered down after all load segments are powered down.
•
If any other condition, such as the Remaining Backup time under or Battery capacity under value being reached occurs during the SIA time, the UPS Network Module starts the shutdown process earlier.
Configuration parameters 54
This following example describes the shutdown parameters for a UPS with two load segments, four connected servers that have HPPP Clients installed on each server, and one UPS Network Module.
Item
7
8
5
6
9
10
3
4
1
2
11
12
Description
Utility failure
Utility restore
Utility
Client 1on load segment 1
Client 2 on load segment 1
UPS Network Module setting for load segment 1
Load segment 1
Client 3 on load segment 2
Client 4 on load segment 2
UPS Network Module setting for load segment 2
Load segment 2
UPS
On utility t1 t2 t3 t4 t5, t6, t7
On battery (SIA)
Operating system shutdown time (OST)
Utility failure—UPS is on battery, and all servers are powered as usual
Shutdown process initiated—Shutdown scripts run, applications close, and the operating system shuts down
All servers are completely powered down. Load segments power down, and then the UPS powers down.
Utility restore
The UPS, load segment 1, and load segment 2 are powered up
When the utility power is lost, the example UPS behaves as follows:
Configuration parameters 55
1.
2.
3.
On load segment 1: a.
Client1—The UPS Network Module waits until t2 to start OST. The server is powered down before t3. b.
Client2—The UPS Network Module waits until t2 to start OST. The server is powered down sometime t3. c.
UPS Network Module—The UPS Network Module waits until t2 to send shutdown commands to load segment 1 and all Clients. Load segment 1 powers down at t3.
On load segment 2: a. b.
Client3—Because the OST of this Client is the longest, it replaced the OST of the UPS Network
Module after it was connected to the UPS Network Module. Client 3 powers down as configured.
Client4—Because the SIA of the UPS Network Module is less than that of Client 4, the UPS Network
Module starts the shutdown process first. Client 4 is forced to start its OST at the same time. c.
UPS Network Module—The UPS Network Module waits until t2 to initiate the shutdown sequence for load segment 2 and the other Clients. Load segment 2 powers down at a new t3 which is the same as the longest Client OST.
UPS—Between the two OST of UPS Network Module on load segment 1 and load segment 2, the UPS starts its countdown at t2 of UPS Network Module on load segment 2, because it received the shutdown command from it first and then powered down at t3 of UPS Network Module on load segment 2 also because it ends last.
When the utility power is restored, the example UPS behaves as follows:
1. t5—If the Battery capacity exceeds condition exists, the UPS is powered on.
2.
3. t6 and t7—If the Switch On after condition exists, the LS is powered on.
If Automatic Power ON is enabled in the BIOS setup of the Client server, the server will be powered on as soon as power is detected.
Configuration parameters 56
Updating the firmware
Updating the firmware overview
Use the Firmware Upload screen (on page 47 ) to update the UPS Network Module firmware.
During the boot process, if the UPS Network Module detects that the application is corrupted, you are prompted to enter the TFTP server IP address. This process is only available when the application is damaged.
To update the firmware image from the bootloader:
1.
Setup a TFTP server.
2.
3.
4.
5.
6.
Load the firmware image, and then rename the image to image.bin.
Copy the image.bin file to the default directory.
------------------------------------------------------------------------
-----
HP
NETWORK MANAGEMENT CARD
BOOTLOADER VERSION : 1.1
------------------------------------------------------------------------
-----
RAM autotest in progress.
RAM autotest SUCCESS.
Commercial reference : 66102
Kitting technical level : 12
Kitting revision : GD
Ethernet MAC Address : 00:20:85:FD:A1:9C
Serial number : BJ0L050LD
PHY autotest SUCCESS
The application in FLASH is corrupted !!!
Run the TFTP server to download the image.bin file
Set the TFTP server IP address :
Enter the IP address of the TFTP server, and then press Enter.
Updating the firmware 57
Firewall configuration
Configuring the firewall on Windows
NOTE: For other operating systems, see the operating system documents on enabling or disabling ports on the firewall.
Windows Firewall blocks most communication through unused IP ports. This prevents a server with the HPPP
Client installed from using the following four ports to communicate with the UPS Network Module:
•
4679/UDP and TCP (Client)
•
4680/UDP and TCP (Client)
•
5000/TCP (Alarms)
•
5001/TCP (Alarms)
To configure the Windows XP with Service Pack 2 Firewall to make an exception for ports 4679, 4680,
5000, and 5001:
1.
Click Start, select Control Panel, and then double-click Network Connections. The Network Connections screen appears.
2.
Right-click the network connection where you are configuring the firewall, and then select Properties.
The Properties screen appears.
Firewall configuration 58
3.
4.
Click the Advanced tab.
In the Windows Firewall box, click Settings.
5.
The Windows Firewall screen appears.
On the General tab, verify that the Windows Firewall is enabled (On) and that the Don't allow exceptions checkbox is not checked.
Firewall configuration 59
6.
Click OK.
7.
8.
On the network Properties screen, click the Exceptions tab.
Be sure that the File and Printer Sharing check box is selected.
Firewall configuration 60
9.
Click Add Port to allow communication through ports 4679, 4680, 5000, and 5001.
10.
11.
12.
The Add a Port screen appears.
Enter a name for the HPPP Client port in the Name field.
Enter 4679, 4680, 5000, or 5001 in the port number field.
Select the appropriate radio button.
Firewall configuration 61
13.
Click Change scope to add more security to the port exception.
Firewall configuration 62
Firewall configuration 63
14.
The Change Scope screen appears.
Select the Custom list radio button, and then add the IP addresses that are allowed to communicate through the specified port.
Firewall configuration 64
15.
Click OK to save the scope settings.
16.
17.
On the Edit a Port screen, click OK to finish adding the exception port.
The Windows Firewall screen displays the newly added HPPP Client port.
Click OK.
NOTE: Software that helps to protect your computer and blocks access on the network, such as
Windows® Defender or firewalls, needs to be reconfigured.
Firewall configuration 65
Firewall configuration 66
Security considerations
Security considerations overview
The UPS Network Module implements strict security for two important reasons:
•
The UPS Network Module manages devices that have the potential to perform operations that are sensitive and destructive.
•
The UPS Network Module has browser accessibility.
To better ensure the security of the UPS Network Module and the devices it manages, consider the following topics in accordance with your organization's security policies and the environment in which the UPS
Network Module operates.
•
Remote access to the UPS Network Module requires a user account. Logging in requires the use of a user name and password, which should be kept properly secured.
•
Each account can be given different access levels, providing different capabilities. Ensure that the appropriate access level is granted to users.
•
Browsing to the UPS Network Module can be done using SSL, which encrypts the data between the browser and UPS Network Module. The UPS Network Module is supported by a 128-bit encryption level. SSL also provides authentication of the UPS Network Module by means of its digital certificate.
Securely importing this certificate must be done to ensure the identification of the UPS Network Module.
Security considerations 67
Alert messages
UPS alarms
•
Emergency Power Off
•
Emergency Power Off Cleared
•
UPS ABM Controller Disabled
•
UPS ABM Controller Enabled
•
UPS AC Module Failure
•
UPS AC Module Failure Cleared
•
UPS Auto Bypass Overload
•
UPS Auto Bypass Overload Cleared
•
UPS Battery Charger Failure
•
UPS Battery Charger Failure Cleared
•
UPS Battery Discharged
•
UPS Battery Discharged Cleared
•
UPS Battery Disconnected
•
UPS Battery Disconnected Cleared
•
UPS Battery Low
•
UPS Battery Low Cleared
•
UPS Battery Over Voltage
•
UPS Battery Over Voltage Cleared
•
UPS Battery Test Failure
•
UPS Battery Test Failure Cleared
•
UPS Bypass AC Phase Out of Range
•
UPS Bypass AC Phase Out of Range Cleared
•
UPS Bypass Frequency Out Of Range
•
UPS Bypass Frequency Out Of Range Cleared
•
UPS Bypass Not Available
•
UPS Bypass Not Available Cleared
•
UPS Bypass Voltage Out Of Range
•
UPS Bypass Voltage Out Of Range Cleared
•
UPS Client Communication Lost
Alert messages 68
•
UPS Client Communication Restored
•
UPS DC Bus High Negative Voltage
•
UPS DC Bus High Negative Voltage Cleared
•
UPS DC Bus High Positive Voltage
•
UPS DC Bus High Positive Voltage Cleared
•
UPS DC Bus Low Negative Voltage
•
UPS DC Bus Low Negative Voltage Cleared
•
UPS DC Bus Low Positive Voltage
•
UPS DC Bus Low Positive Voltage Cleared
•
UPS Fan Failure
•
UPS Fan Failure Cleared
•
UPS In High Efficiency Mode
•
UPS Input AC Not Present
•
UPS Input AC Not Present Cleared
•
UPS Input AC Over Voltage
•
UPS Input AC Over Voltage Cleared
•
UPS Input AC Under Voltage
•
UPS Input AC Under Voltage Cleared
•
UPS Input Frequency Out Of Range
•
UPS Input Frequency Out Of Range Cleared
•
UPS Internal Configuration Failure
•
UPS Internal Configuration Failure Cleared
•
UPS Internal Failure
•
UPS Internal Failure Cleared
•
UPS Inverter Failure
•
UPS Inverter Failure Cleared
•
UPS Inverter Over Voltage
•
UPS Inverter Over Voltage Cleared
•
UPS Inverter Overload
•
UPS Inverter Overload Cleared
•
UPS Inverter Under Voltage
•
UPS Inverter Under Voltage
•
UPS Load Segment 1 Is Off
•
UPS Load Segment 1 Is On
•
UPS Load Segment 2 Is Off
•
UPS Load Segment 2 Is On
Alert messages 69
•
UPS Load Segment 3 Is Off
•
UPS Load Segment 3 Is On
•
UPS On Auto Bypass
•
UPS On Auto Bypass Cleared
•
UPS On Battery
•
UPS On Battery Cleared
•
UPS On Boost
•
UPS On Boost Cleared
•
UPS On Buck
•
UPS On Buck Cleared
•
UPS On Manual Bypass
•
UPS On Manual Bypass Cleared
•
UPS Output Is Off
•
UPS Output Is On
•
UPS Output Overload
•
UPS Output Overload Cleared
•
UPS Output Overload Level 1
•
UPS Output Overload Level 1 Cleared
•
UPS Output Overload Level 2
•
UPS Output Overload Level 2 Cleared
•
UPS Output Short Circuit
•
UPS Output Short Circuit Cleared
•
UPS Over Temperature
•
UPS Over Temperature Cleared
•
UPS Rectifier Failure
•
UPS Rectifier Failure Cleared
•
UPS Rectifier Overload
•
UPS Rectifier Overload Cleared
•
UPS Redundant Communication Lost
•
UPS Redundant Communication Restored
•
UPS Shutdown Imminent
•
UPS Shutdown Imminent Cleared
•
UPS Shutdown in {time}
•
UPS Shutdown Pending
•
UPS Single Wave Load Fault
•
UPS Single Wave Load Fault Cleared
Alert messages 70
•
UPS Site Wiring Fault
•
UPS Site Wiring Fault Cleared
Alert messages 71
SNMP trap codes
SNMP trap codes
10
10
11
11
12
12
13
8
9
9
7
8
15
16
16
17
17
18
13
14
14
15
18
19
4
4
5
3
3
6
7
5
6
1
2
This information is for reference only.
SNMP trap code SNMP trap message
UPS Shutdown in {time}
UPS Shutdown Pending
UPS Battery Disconnected
UPS Battery Disconnected Cleared
UPS Battery Discharged Cleared
UPS Battery Discharged
UPS Battery Over Voltage Cleared
UPS Battery Over Voltage
UPS Battery Charger Failure Cleared
UPS Battery Charger Failure
UPS ABM Controller Disabled
UPS ABM Controller Enabled
UPS Load Segment 1 Is Off
UPS Load Segment 1 Is On
UPS Load Segment 2 Is Off
UPS Load Segment 2 Is On
UPS Load Segment 3 Is Off
UPS Load Segment 3 Is On
UPS On Boost Cleared
UPS On Boost
UPS On Buck Cleared
UPS On Buck
UPS Input Frequency Out Of Range Cleared
UPS Input Frequency Out Of Range
UPS AC Module Failure Cleared
UPS AC Module Failure
UPS Input AC Not Present Cleared
UPS Input AC Not Present
UPS Input AC Over Voltage Cleared
UPS Input AC Over Voltage
UPS Input AC Under Voltage Cleared
UPS Input AC Under Voltage
UPS Site Wiring Fault Cleared
UPS Site Wiring Fault
UPS Bypass Frequency Out Of Range Cleared
SNMP trap codes 72
SNMP trap code
25
25
26
27
27
28
28
21
22
22
23
19
20
20
21
23
24
24
31
31
32
32
33
29
29
30
30
35
36
36
37
37
38
33
34
34
35
38
39
39
40
40
41
41
SNMP trap message
UPS Bypass Frequency Out Of Range
UPS Bypass Not Available
UPS Bypass Not Available Cleared
UPS Auto Bypass Overload Cleared
UPS Auto Bypass Overload
UPS Bypass AC Phase Out of Range Cleared
UPS Bypass AC Phase Out of Range
UPS On Auto Bypass Cleared
UPS On Auto Bypass
UPS Bypass Voltage Out Of Range Cleared
UPS Bypass Voltage Out Of Range
UPS On Manual Bypass Cleared
UPS On Manual Bypass
UPS In High Efficiency Mode
UPS Inverter Failure Cleared
UPS Inverter Failure
UPS Inverter Overload Cleared
UPS Inverter Overload
UPS Inverter Over Voltage Cleared
UPS Inverter Over Voltage
UPS Inverter Under Voltage Cleared
UPS Inverter Under Voltage
UPS Output Overload Level 1 Cleared
UPS Output Overload Level 1
UPS Output Overload Level 2 Cleared
UPS Output Overload Level 2
UPS Output Short Circuit Cleared
UPS Output Short Circuit
UPS Single Wave Load Fault Cleared
UPS Single Wave Load Fault
UPS DC Bus High Negative Voltage Cleared
UPS DC Bus High Negative Voltage
UPS DC Bus High Positive Voltage Cleared
UPS DC Bus High Positive Voltage
UPS Rectifier Failure Cleared
UPS Rectifier Failure
UPS DC Bus Low Negative Voltage Cleared
UPS DC Bus Low Negative Voltage
UPS DC Bus Low Positive Voltage Cleared
UPS DC Bus Low Positive Voltage
UPS Rectifier Overload Cleared
UPS Rectifier Overload
UPS Client Communication Restored
UPS Client Communication Lost
SNMP trap codes 73
SNMP trap code
47
48
48
49
49
50
50
44
44
45
45
42
42
43
43
46
46
47
53
53
54
54
51
51
52
52
SNMP trap message
UPS Redundant Communication Restored
UPS Redundant Communication Lost
UPS On Battery
UPS On Battery Cleared
UPS Battery Low Cleared
UPS Battery Low
UPS Communication Restored
UPS Communication Lost
UPS Internal Configuration Failure Cleared
UPS Internal Configuration Failure
Emergency Power Off Cleared
Emergency Power Off
UPS Fan Failure Cleared
UPS Fan Failure
UPS Output Is Off
UPS Output Is On
UPS Internal Failure Cleared
UPS Internal Failure
UPS Battery Test Failure Cleared
UPS Battery Test Failure
UPS Output Overload Cleared
UPS Output Overload
UPS Over Temperature Cleared
UPS Over Temperature
UPS Shutdown Imminent Cleared
UPS Shutdown Imminent
SNMP trap codes 74
Specifications
Technical characteristics
Item Description
Physical characteristics
Dimensions (width x depth x height)
Weight
RoHS
Storage
Storage temperature range
Ambient conditions
Operating temperature range
Relative humidity
Card performance
Supply voltage
Supply current (all LEDs on)
Functions
Web supervision
Languages
Alarms
Log
Server protection
Network
Identification
Security
Browsers
NMS
MIB
Settings (default values)
IP network
Web interface access control
132 x 66 x 42 mm (5.20 x 2.60 x 1.65 in)
70 g (.15 lb)
100% compatible
-10°C to 70°C (14°F to 158°F)
0°C to 40°C (32°F to 104°F)
90% maximum, noncondensing
5V ±5%
300 mA maximum
HTTP—5 browser windows maximum
HTTPS—3 browser windows maximum
English or Japanese
Email, SNMP trap, web interface
400 measurements or events
Up to 100 servers protected
Fast ETHERNET, 10/100 Mb/s, autonegotiation
HTTP 1.1, SNMP V1, SNMP V3, NTP, TFTP,
SMTP, DHCP
User name and password
SSL 3.0, TLS 1.0
Microsoft® Internet Explorer 6.x or higher
HP Systems Insight Manager
Standard IETF UPS MIB (RFC 1628)
HP Power MIB (cpqpower.mib)
DHCP enabled
IP address: 192.168.1.2 (manual configuration)
Subnet mask: 255.255.0.0
Gateway: 0.0.0.0
NTP server: pool.ntp.org
User name: admin
Password: admin
Specifications 75
Item
Configuration menu access control
Date and time
Settings/AUX connector
Description
Password: admin (not modifiable)
Synchronize with HP Power Protector
9600 bits/s, 8 bits, 1 bit stop, no parity
Default parameters
Parameter Default value
Network
IP address
Subnet mask
Gateway Address
BOOTP/DHCP
IPv6 Enabled
IPv6 Auto Config Enabled
Firmware Upload
SMTP server
System
UPS Contact
UPS Location
History log interval (sec.)
Default Language
Notified Application table
—
Access control
User name
Password
SNMP
Community name read
—
192.168.1.2
255.255.0.0
0.0.0.0
Enabled
Enabled
Enabled
Enabled smtpserver
—
Computer Room Manager
Computer Room
60
English
— empty
— admin admin
— public
Trap port
SNMP Version
Read-Only User
Read-Only Security Level
Read-Only Password
Read-Write User
Read-Write Security Level
Read-Write Password
Date and time
Date and time adjustment
NTP server
Serial link
162
V1&V3 readuser
Authentication readuser wirteuser
Authentication&Privacy writeuser
—
Accept automatic update from
HP Power Protector ntpserver
—
Possible value
—
Network IP address
Network IP address
Network IP address
Active / Deactivated
Active / Deactivated
Active / Deactivated
Active / Deactivated
49 characters maximum
—
49 characters maximum
31 characters maximum
10 to 99999 sec.
English / Japanese
—
NA
—
5 characters minimum, 31 characters maximum
5 characters minimum, 31 characters maximum
—
32 alphanumeric characters maximum, no spaces
Not configurable
Disabled, V1, V3, V1&V3
1 character minimum, 32 characters maximum
None, Authentication, Authentication&Privacy
8 characters minimum, 24 characters maximum
1 character minimum, 32 characters maximum
None, Authentication, Authentication&Privacy
8 characters minimum, 24 characters maximum
—
Synchronize with an NTP server, Accept automatic update from HP Power Protector,
Synchronize manually
49 characters maximum
—
Specifications 76
Parameter
Speed
Data bits
Stop bits
Parity
Flow control
Default value
9600 baud
8
1 without without
Possible value
Not configurable
Not configurable
Not configurable
Not configurable
Not configurable
Specifications 77
Troubleshooting
Client communication failure with HP UPS Network
Module in a VMware operating system
Possible Cause: The Client was installed on the guest operating system.
Action: Install the Client on the host VMware operating system (for ESX) or on VIMA/VMA (for ESXi). Do not install the Client on the guest operating system. When the Client receives a shutdown notification from the HP
UPS Network Module, it sends an operating system shutdown command to the VMware host operating system, and then the VMware shuts down the guest operating system based on a preset configuration.
Client server is not restarting
Symptom: Utility power has been restored, the UPS and its load segments are powered on, but the Client server does not restart.
Possible Cause: The “Automatic Power ON” server setup setting might be disabled.
Action: In the server system BIOS, change the setting for Automatic Power ON to "Enabled."
Clients cannot communicate with UPS after swapping
HP UPS Network Module with another UPS
Possible Cause: The HP UPS Network Module and Clients are configured with an old power source.
Action: Reconfigure the HP UPS Network Module power source, and then reconfigure the Client power source.
Failure to communicate with the serial or USB ports
Symptom: There is a failure to communicate with the serial or USB ports while upgrading the UPS or
CommBoard firmware.
Possible Cause: A UPS Network Module is installed in the UPS minislot.
Action: Remove the UPS Network Module from the UPS minislot when upgrading the firmware using the serial or USB ports.
Forgot login password
Action: To reset the login password, use the supplied serial cable to connect to the UPS Network Module through a terminal emulation programs, such as HyperTerminal, with the following parameters:
Troubleshooting 78
•
Bits per second—9600
•
Data bits—8
•
Parity—None
•
Stop bits—1
•
Flow control—None
The default password to access the serial configuration menu is “admin”.
UPS Network Module fails to boot after upgrading the firmware
Possible Cause: The application might be corrupted due to an interruption while flashing the firmware.
Action:
1.
Using the supplied serial cable, connect to the UPS Network Module through a terminal emulation program, such as HyperTerminal, with the following parameters: o
Bits per second—9600 o o
Data bits—8
Parity—None o o
Stop bits—1
Flow control—None
In the HyperTerminal window, the UPS Network Module Bootloader prompts for a TFTP IP address.
2.
3.
4.
5.
6.
7.
Setup a TFTP server.
Copy the UPS Network Module firmware image file to the TFTP server default folder.
Rename the UPS Network Module image file to image.bin.
Launch the TFTP.
Enter the TFTP server IP address at the prompt on the terminal emulation program window.
Press Enter.
UPS is not powered on after a scheduled shutdown
Possible cause: The Restart time value might be configured as less than the Shutoff time value.
Action: Configure the Restart time to a greater value than the Shutoff time value.
Troubleshooting 79
Support and other resources
Before you contact HP
Be sure to have the following information available before you call HP:
•
Active Health System log
Download and have available an Active Health System log for 3 days before the failure was detected.
For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website ( http://www.hp.com/go/ilo/docs ).
•
Onboard Administrator SHOW ALL report (for HP BladeSystem products only)
For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website
( http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c
02843807 ).
•
Technical support registration number (if applicable)
•
Product serial number
•
Product model name and number
•
Product identification number
•
Applicable error messages
•
Add-on boards or hardware
•
Third-party hardware or software
•
Operating system type and revision level
HP contact information
For United States and worldwide contact information, see the Contact HP website
( http://www.hp.com/go/assistance ).
In the United States:
•
To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be recorded or monitored.
•
If you have purchased a Care Pack (service upgrade), see the Support & Drivers website
( http://www8.hp.com/us/en/support-drivers.html
). If the problem cannot be resolved at the website, call 1-800-633-3600. For more information about Care Packs, see the HP website
( http://pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html
).
Support and other resources 80
Regulatory compliance notices
Regulatory compliance identification numbers
For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number is not the marketing name or model number of the product.
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio
Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and
B, depending upon their intended installation. Class A devices are those that may reasonably be expected to be installed in a business or commercial environment. Class B devices are those that may reasonably be expected to be installed in a residential environment (for example, personal computers). The FCC requires devices in both classes to bear a label indicating the interference potential of the device as well as additional operating instructions for the user.
FCC rating label
The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After you determine the class of the device, refer to the corresponding statement.
FCC Notice, Class A Equipment
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense.
FCC Notice, Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
Regulatory compliance notices 81
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio or television technician for help.
Declaration of conformity for products marked with the FCC logo, United States only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For questions regarding this product, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
•
1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded or monitored.)
For questions regarding this FCC declaration, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
•
1281-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Canadian notice (Avis Canadien)
Class A equipment
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Regulatory compliance notices 82
Class B equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
European Union regulatory notice
Products bearing the CE marking comply with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
•
Ecodesign Directive 2009/125/EC, where applicable
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by HP.
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family and available (in English only) either within the product documentation or at the following HP website
( http://www.hp.eu/certificates ) (type the product number in the search field).
The compliance is indicated by one of the following conformity markings placed on the product:
For non-telecommunications products and for EU harmonized telecommunications products, such as
Bluetooth® within power class below 10mW.
For EU non-harmonized telecommunications products (If applicable, a 4-digit notified body number is inserted between CE and !).
Please refer to the regulatory label provided on the product.
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger
Strasse 140, 71034 Boeblingen, GERMANY.
Disposal of waste equipment by users in private households in the European Union
Regulatory compliance notices 83
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Chinese notice
Class A equipment
Japanese notice
Korean notice
Class A equipment
Regulatory compliance notices 84
Class B equipment
BSMI notice
Regulatory compliance notices 85
Acronyms and abbreviations
AC alternating current
BOOTP
Bootstrap Protocol
DC domain controller
DHCP
Dynamic Host Configuration Protocol
DNS domain name system
HPPP
HP Power Protector
HTTPS hypertext transfer protocol secure sockets
IPv4
Internet Protocol version 4
IPv6
Internet Protocol version 6 kVA kilovolt-ampere
MAC
Media Access Control
MIB management information base
Acronyms and abbreviations 86
NTP network time protocol
SIM
Systems Insight Manager
SMS short message service
SSL
Secure Sockets Layer
TFTP
Trivial File Transfer Protocol
UDP
User Datagram Protocol
UPS uninterruptible power system
USB universal serial bus
Acronyms and abbreviations 87
Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback ( mailto:[email protected]
).
Include the document title and part number, version number, or the URL when submitting your feedback.
Documentation feedback 88
Index
A
accessing the configuration menu 48
alarm conditions 68 alarms, viewing 24, 68
B
C
class A equipment 81 class B equipment 81
configuration menu, accessing 48 configuration menu, navigating 48 configuration menu, overview 48
configuration, hardware 7 configuration, network 7
configuring firewall settings 58
D
date and time 34 daylight saving time, setting up 34
discovering the network module 51
E
Email Message Settings screen 46
Email Notification screen 44 email notifications, setting up 44
Event Log screen 28 event log, exporting 28
F
factory defaults, resetting 30, 49
Federal Communications Commission (FCC)
firewall settings, configuring 58
G
Google Chrome, secure session 19
H
HP Systems Insight Manager overview 50
HP UPS Network Module Configuration Menu 48
HP UPS Network Module overview 6
I
installation precautions 12 installing hardware 12 installing the unit 12
IP address, configuring 32, 49
Index 89
J
K
L
logging in, through a browser 16
M
N
navigating the configuration menu 48
network access, configuring 32, 49
Network Configuration submenu 49
network module, discovering 51
Notified Applications screen 42
NTP parameters, configuring 34
O
operating system shut down 35, 54
overview of configuration procedure 10
overview, configuration menu 48
overview, HP Power Protector 7
overview, HP UPS Network Module 6
P
Q
R
regulatory compliance identification numbers 81
regulatory compliance notices 81, 83
S
secure sessions, Google Chrome 19
secure sessions, Internet Explorer 17
Shutdown Parameters screen 35, 54
SNMP trap notifications, setting up 50, 52
SNMP trap receivers, configuring 43
supported hardware configurations 7
Systems Insight Manager, overview 50
T
Trap Receivers Settings screen 43
Index 90
U
V
W
web interface, accessing 16 web interface, overview 16
web interface, using and navigating 19
Index 91
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 HP UPS Network Module User Guide
- 1 Abstract
- 2 Notice
- 3 Contents
- 6 Overview
- 6 Overview
- 6 Features
- 7 HP Power Protector overview
- 7 Supported hardware configurations
- 7 Configuration A
- 8 Configuration B
- 9 Web interface requirements
- 10 Quick installation and setup overview
- 11 Component identification
- 11 Front panel connectors and LED indicators
- 12 Installing the HP UPS Network Module
- 12 Precautions
- 12 Required tools
- 12 Installing the UPS Network Module
- 13 Connecting the network cable
- 14 Connecting the configuration cable
- 14 Launching a terminal emulation program
- 15 Configuring the UPS Network Module network settings
- 16 HP UPS Network Module web interface
- 16 HP UPS Network Module web interface overview
- 16 Accessing the web interface
- 17 Browser security alert
- 17 Establishing a secure session for Internet Explorer
- 18 Establishing a secure session for Mozilla
- 18 Establishing a secure session for Firefox
- 19 Establishing a secure session for Google Chrome
- 19 Navigating the web interface
- 19 Views
- 20 Power Source screen
- 23 UPS Status table
- 24 UPS Alarms table
- 24 About your UPS table
- 25 Manual Control screen
- 26 Logs
- 26 UPS Data Log screen
- 28 Event Log screen
- 29 System Log screen
- 29 Settings
- 30 System Settings screen
- 31 Access Control screen
- 32 Network Settings screen
- 34 Time Settings screen
- 35 Shutdown Parameters screen
- 39 Scheduled Shutdown screen
- 41 SNMP Settings screen
- 42 Notified Applications screen
- 43 Trap Receivers Settings screen
- 44 Email Notification screen
- 46 Email Message Settings screen
- 47 Firmware Upload screen
- 48 HP UPS Network Module Configuration Menu
- 48 HP UPS Network Module Configuration Menu overview
- 48 Accessing the Service Menu
- 48 Navigating the menus
- 48 Main menu
- 49 Reset submenu
- 49 Network Configuration submenu
- 50 Systems Insight Manager integration
- 50 Systems Insight Manager overview
- 51 Discovering the UPS Network Module
- 52 Configuring HP SIM to receive traps
- 52 Configuring the UPS Network Module to send traps to HP SIM
- 53 Optional power monitoring using SNMP
- 53 SNMP monitoring
- 54 Configuration parameters
- 54 Shutdown parameters
- 57 Updating the firmware
- 57 Updating the firmware overview
- 58 Firewall configuration
- 58 Configuring the firewall on Windows
- 67 Security considerations
- 67 Security considerations overview
- 68 Alert messages
- 68 UPS alarms
- 72 SNMP trap codes
- 72 SNMP trap codes
- 75 Specifications
- 75 Technical characteristics
- 76 Default parameters
- 78 Troubleshooting
- 78 Client communication failure with HP UPS Network Module in a VMware operating system
- 78 Client server is not restarting
- 78 Clients cannot communicate with UPS after swapping HP UPS Network Module with another UPS
- 78 Failure to communicate with the serial or USB ports
- 78 Forgot login password
- 79 UPS Network Module fails to boot after upgrading the firmware
- 79 UPS is not powered on after a scheduled shutdown
- 80 Support and other resources
- 80 Before you contact HP
- 80 HP contact information
- 81 Regulatory compliance notices
- 81 Regulatory compliance identification numbers
- 81 Federal Communications Commission notice
- 81 FCC rating label
- 81 FCC Notice, Class A Equipment
- 81 FCC Notice, Class B Equipment
- 82 Declaration of conformity for products marked with the FCC logo, United States only
- 82 Modifications
- 82 Canadian notice (Avis Canadien)
- 83 European Union regulatory notice
- 83 Disposal of waste equipment by users in private households in the European Union
- 84 Chinese notice
- 84 Japanese notice
- 84 Korean notice
- 85 BSMI notice
- 86 Acronyms and abbreviations
- 88 Documentation feedback
- 89 Index