advertisement
ChannelPlus Video Camera
Installing the Camera
The H722 video cameras
are solid state cameras designed to fit deep double gang J-boxes.
The H722 must be used with one of its companion channel injectors
(H511HHR or H511BID). When used with an H511, video received from the H722 is used to create a new channel to add to existing television channels. The H722 is connected to the H511 by a single run of CAT-5 wire. Although this camera mount is intended for use indoors, or under an eave, a drip cap is supplied for use in exposed areas.
The H722 is designed to be mounted outside in a J-box or inside into dry wall. When mounting outside, use the supplied drip cap and gasket. When mounting inside, use the supplied CADDY bracket.
The H722 series cameras work best when they are looking down on their subject. For a front door application, place the camera about 7 feet off the ground, adjacent to the door.
Outside
Installation
Inside
Installation
Two models are available:
Model H722
Black & White, 2 lux, 3.6 mm lens, smoked window
Model H722C
Color, 8 lux, 3.6 mm lens, smoked window
Deep double-gang
J-box
Note: The H722 is not a standalone video camera
Use only with an H511 channel injector.
drip cap gasket frame
CADDY bracket frame
Typical Installation
Connect the H722 camera using only one method:
1 Terminate cable with a CAT-5 jack and connect to the H511 using supplied RJ45 jumper. (Also see example H628 manual).
2 Wire camera or wall plate directly to the 8 position terminal block matching the CAT-5 wire colors to the colors on the terminal block.
Insert wires and tighten screws.
Use these parts
Use these parts
Drywall
1 Attach drip cap, gasket & frame
2
Make a square cut-out in the drywall that is 3¾” wide by
3½” high. Insert clip into drywall, and bend to form.
Program
1
CAT-5 video
Insert 6-32 screws into frame and bottom holes of 2 gang box
1
CADDY® bracket
Output
CATV
/Ant Power
Note: bottom lip of drip cap goes inside frame.
(You may have to rotate drip Channel Injector Power the H511 last make all cable and
CAT-5 connections first.
Channel Injector
(H511HHR shown) Connect antenna or incoming cable to H511 CATV/Ant input.
Prepare the CAT-5 wires by stripping
1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws.
Prepare the CAT-5 wires by stripping
1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws.
Connect H511 output to splitter or distribution panel input.
(See H511 manual)
2 2
Maximum CAT-5 run:
H722 to H511
H722C to H511
300 feet
100 feet
Insert camera at an angle and rotate into place.
Insert camera at an angle and rotate into place. Make sure gasket is behind camera
Add RTV to seal from weather
Add top screws
Add top screws
H722
(rear view)
3 3
Insert wire into terminal block and tighten screws. Use the color bar to match wire colors. The color bar has two rows, one for CAT-5 and one for quad wire:
- For CAT-5 wire, remove the default resistor and use all 8 wires.
*
* The H722/H722C was designed to work with CAT-5 wiring. Although the system will function with quad wire, CAT-5 delivers the highest quality picture. CAT-5 allows the use of an automatic line length sensor and picture compensator. Quad wire does not take advantage of this enhancement.
Specifications:
typical @ 25 C ± 5 C
Model
Image format
H722
EIA (Black & White )
Resolution, horizontal 525 lines
Resolution
Minimum illumination
Signal to Noise ratio
AGC
Lens
Lens viewing angle
350 lines
2 lux
>45 dB
Yes
3.6mm F2.0
78 O
White balance
Electronic shutter speed
Maximum distance to H511 automatic
1/60 to 1/50000 second
300 feet
H722C
NTSC (Color)
525 lines
350 lines
8 lux
>45 dB
Yes
3.6mm F2.0
78 O automatic
1/60 to 1/50000 second
100 feet
Aiming the Camera
Insert 1/8“ screwdriver in the steering slot below the lens.
Using the screwdriver, bend the mount to point the camera in the desired direction.
4
Never use camera to bend the mount!
Attaching the Window
5
Window rides on the lip of the frame.
Rotate downward and snap into place.
DECLARATION OF CONFORMITY
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Installation requirements:
FCC classifies this product under part 15 of its rules as a “television interface device”.
Systems designed using television interface devices have the following legal requirements:
1) The modulated channel signal strength may not exceed 15.56dBmV at any television.
Federal Regulation 47CFR15.115(b)(1)(i).
2) If an antenna is used in the system, the modulated channel signal strength may not exceed
-51dBmV at the antenna input port.
Federal Regulation 47CFR15.115(c)(4).
For the Installer:
Any system you design must comply with these regulations. As the installer, you are responsible. The H722 or H722C (when used with an H511) has the necessary characteristics to comply with the above requirements as designed without additional accessories.
The H511HHR is suitable for use with an antenna or with CATV systems.
The H511BID is suitable for use with CATV systems only.
92821 92821 Brea,CA Brea,CA
.B
.B
600-173Rev 600-173Rev echnology,Inc., echnology,Inc., MultiplexT MultiplexT or player,a
V handles
(AnA run’ house wiresfrom data hi-speeddata modem,hi-speed
Vmodulators,
,cable
,A
Vmodulators ,A satellitereceiver satellitereceiver satellitereceiver cablemodem satellitereceiver
Vmodulators ethernet, receiver,A cablemodem
,
,ethernet
,ethernet,
,
,ethernet,
,ethernet,
,ethernet, phone,TV phone,TV phone,TV phone,TV phone,TV phone,TV phone,satellite phone,TV phone,TV ofthe
P as‘home airs)wire and television(antenna camera,DVD
Runthese modulatorsignals.
wisted fice
2RG-6
2RG-6
3RG-6
3Cat-5
2Cat-5
1Cat-5
HomeOf variousrooms schemes.
T isknown
AV coaxhandles frontdoor forcommunication fromthe nshielded U indicated.
modem,or
3RG-6
3RG-6
3RG-6
2Cat-5
3Cat-5
1Cat-5
MediaCenter channelsfor areused lines.RG-6
forOpenHouse
4-UTP(4 centerlocation.(This therooms followingpre-wire
Room
1RG-6
1RG-6
2RG-6 ofwire newTV receiver.)
OpenHouserun dish,cable
1Cat-5
Typical
2Cat-5
2Cat-5 centerto theservice inan
ahouse
wotypes
4telephone 1to asatellite recommendthe
Best
Good
Better
-
-
ficeroomficeroomficeroom-
Homeof
Mediacenter
Typical
Best…
Homeof
Typical
Better…
Typical
Good...
Homeof
Mediacenter
Mediacenter wiring.)T entertainment:Cat-5, modulatorcreates cable),satellite dataor theservice
We
VCRor
Thecables
Wiring
directlyto
&H722C
Cameras
ModelsH722
Video
ChannelPlus
®
TM
TM
Compatible
ChannelPlus Enclosures, Modules,
Accessories & Wall Plates
Service center enclosures
A full line of OpenHouse compatible enclosures, from simple, inexpensive mounting plates to high capacity in-wall cabinets. AC outlets can be mounted inside the cabinets using a UL listed accessory.
Starter systems
RF splitters and telephone punch downs. When it is time to upgrade, just snap this module out and replace with one of more of the more sophisticated units.
2
R
T
1
R
T
From
Telco
OUT IN OUT IN IN OUT
532-230 5MHz to 1000MHz
SPLITTER COMBINER
OUT IN
Telephones
OUT IN
R
Combo Hub (2 lines x 6 phones, 1input x 4 televisions)
ChannelPlus model H801
Data Hub (8 cables, TIA-568A) Category 5 Compliant
ChannelPlus model H628
Data hubs
Termination blocks for the CAT-5 cables,
Ethernet hubs. Bring the Internet to any room in the home. Or create a home data network.
Telephone hubs
Connections for 1-4 phone lines to every room. Starter hub adds RJ-
31X jack for security system dialer.
4
R
T
3
R
T
2
R
T
1
R
T
From
Telco
Expansion
Ports
RJ31X
Out
Telephone Master Hub (4 lines x 6 phones)
ChannelPlus model H616
Telephones
Wall plates
Wall plate systems for all rooms. The typical room gets TV and telephone. The Home office wall plate adds data ports.
The media center wall plate adds satellite feeds.
Coax panels
Distribute antenna or cable TV to every room of the house. Some models include bi-directional amplifiers for interactive cable systems. Some models include inputs and IR engines.
modulator multiplex ® technology, inc.
3001 Enterprise Street, Brea, CA 92821-6213, U.S.A.
* * * www.channelplus.com
AV modulators
(for service center)
Create a new TV channel for a front door camera. Some models feature
Cat-5 input connections.
®
A B C D select program model 5445 quad digital modulator pll frequency control
AV modulators
(for media center)
Create new TV channels for DVD, VCR, or a satellite receiver. These modulators sit in the media center. Some offer true
MTS stereo.
Warranty
Multiplex Technology, Inc. warrants this product to be free from defects in materials and workmanship for a period of one year from the date of purchase or MTI will repair, or at its option, replace the defective product. To obtain warranty service, call MTI for a return material authorization (RMA) number and return the product prepaid to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, CA
92821, Attention: Customer Service. Please put the RMA number on the outside of the carton.
Any implied warranty arising from the sale of the product including implied warranties of merchantability and fitness for purpose are limited to the warranty stated above. MTI shall not be responsible for losses or damages or expenses, whether direct, consequential or incidental arising from the use of or the inability to use this product. Some states do not allow limitations on how long the implied warranty lasts or the exclusion or limitation or incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
IR Accessories
Control video devices from any room.
New ChannelPlus products are added all the time.
Visit our website to learn more: www.channelplus.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project