advertisement
VMA633
6.5 INCH WIDE LCD MONITOR
VMA633
6.5” WIDE ACTIVE MARTIX TFT
COLOUR LCD MONITOR
OWNER’S MANUAL
INSTALLATION GUIDE
OWNER’S MANUAL
W
ARNING!
THE CLARION VMA633 LCD MONITOR IS DESIGNED FOR NAVIGATION PURPOSE AND REAR
SEAT PASSENGER VIEWING ONLY.
THIS PRODUCT IS NOT INTENDED FOR VIEWING MOVIES BY THE DRIVER WHILE THE VEHICLE
IS IN MOTION. SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVER’S
SAFE OPERATION OF THE VEHICLE AND MAY RESULT IN SERIOUS INJURY OR DEATH. SUCH
USE MAY ALSO VIOLATE STATE LAW. CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY
INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY
IMPROPER OR UNINTENDED USES OF THIS PRODUCT.
I
NTRODUCTION:
The VMA633 is a TFT active matrix colour LCD monitor that delivers a striking picture with superior image resolution. The Clarion VMA633 is a full-feature 6.5” LCD Colour Monitor and has the following topics:
●
6.5” wide-screen colour LCD panel.
●
A bright vibrant clear screen.
●
●
Video composite & RGB 8-pin DIN Style inputs
Built-in speaker for navigation announcements
●
Universal mount for easy installation in different car types
A
BOUT
T
HIS
M
ANUAL
A
ND
W
ARRANTY:
To start enjoying your new Clarion VMA633 monitor, please read the instructions listed in this manual. Keep all instructions for future reference. Please fill out and send in the enclosed warranty card to protect your purchase and aid in warranty service. Also, save your original sales receipt as proof of purchase.
T
ABLE
O
F
C
ONTENTS:
I
NTRODUCTION,
A
BOUT
T
HIS
M
ANUAL
& T
ABLE OF
C
ONTENTS 1
P
RECAUTIONS
& D
ESCRIPTION
O
F
B
UTTONS
A
ND
C
ONNECTORS 2
D
ESCRIPTION
O
F
P
ICTURE
A
DJUSTMENT 3
C
ARE AND
M
AINTENANCE 3
W
IRING
P
RECAUTIONS 3
D
ESCRIPTION
O
F
I
NSTALLATION 4
T
ROUBLESHOOTING 5
S
PECIFICATIONS 5
1
P
RECAUTIONS:
VMA633 6.5” TFT LCD Monitor
●
●
●
●
●
●
●
This monitor is intended for use in DC 12V, negative ground vehicles.
Do not operate the monitor in ways other than described in this guide, doing so may cause damage and void the warranty.
Be careful not to run down the car’s battery while using a multimedia system with the engine stopped. Doing so may damage the vehicle’s battery or the multimedia system.
Do not disassemble or modify monitor. Doing so may damage it and void the warranty.
Keep moisture away from the set. Water and humidity may damage the internal circuitry.
Do not let the monitor become overheated. If the temperature inside the vehicle is high or the monitor has been exposed to direct sunlight, lower the monitor’s temperature before use. (The liquid crystal panel operates within a temperature range of –1~45°C (30~113°F).
In extremely cold temperature, the movement of the picture may slow and the picture may become dark. The monitor will work normally once the temperature increase to its normal operation range.
Small black or shiny dots may been see inside the liquid crystal panel. These are normal when
● manufacturing liquid crystal products.
D
ESCRIPTION OF
B
UTTON
A
ND
C
ONNECTORS:
VMA633
6.5 INCH WIDE LCD MONITOR
1 2 3 4 5 6
7
8
9
10
11
12
13
1. Power Button
2. Dimmer Sensor
3. Remote Sensor
4. Picture Controls
6. Source Controls
7. Video Composite Input
8. 2-Pin Molex Power Connector
9. IR Serial Remote OUT
5. Wide Mode Controls 10.
8-Pin RGB input DIN cable
11.Speaker -
(White w.Black line)
12.Speaker + (White)
13.Dimmer Lead
(Orange)
2
OWNER’S MANUAL
D
ESCRIPTION OF
P
ICTURE
A
DJUSTMENT:
●
Press the PICTURE SELECT button several times, the screen will display the picture control
Bar in the following order sequentially.
(BLANK) àBRIGHTNESSàCONTRASTàCOLOURàTINTàDIMMERàMEM RESET─
Before the display disappears, use the PICTURE SELECT UP (VOLUME UP) button or PICTURE
●
●
SELECT DOWN (VOLUME DOWN) button, to adjust the picture quality.
COLOUR
← →
DOWN UP
●
Press the WIDE/NORMAL button, the screen will display 16:9 or 4:3 picture.
DIMMER:Press UP、DOWN or Brightness to choose seven different sets.
Auto Brightness automatically
DASHBOARD Controlled by Dashboard illumination
●
MEM RESET :Press UP or DOWN, all sets return the initial value.
C
ARE
A
ND
M
AINTENANCE:
Cleaning the Cabinet:
●
Use a soft, dry cloth to gently wipe off any dirt.
●
Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or cause the point to peel.
Cleaning the LCD Panel:
●
●
Use a soft, dry cloth to gently wipe off any dust.
The surface is easily scratched, do not rub it with hard objects.
W
IRING
P
RECAUTIONS:
Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer.
1.Disconnect the negative (-) lead from the vehicle’s battery before making any connections.
2.When creating passage holes through metal or plastic, use grommets to
Eliminate any sharp edges created during drilling. This will protect power or video wires from nicks or damaged causing a possible short circle or failure.
3.When connecting the ground lead, fasten the ground lead (black) securely to a clean metal plate on the vehicle. Use sandpaper to remote any paint from the surface where the ground terminal is attached.
D
ESCRIPTION OF
I
NSTALLATION:
Now the VMA633 is useable with including mounting bracket. The VMA633 monitor will accept a video signal from any video source with composite video output.
The Infrared
(IR) sensor will work with a Clarion NAX9500E using the CCE-001 adapter and IR extension cable, which are provided.
3
VMA633 6.5” TFT LCD Monitor
1. Look over the vehicle for a monitor location. Each vehicle is different and locations will vary. Make sure the monitor will not interfere with the driver’s safe operation of vehicle.
2. Once a location has been determined, run the 3.5 mm IR extension, Video Composite and power Molex connector into the monitor’s mounting location.
3. Plug main cable into the monitor.
4. Run the IR extension, video, and power cables to their respective destinations.
VMA633
6.5 INCH WIDE LCD MONITOR
1 RED
2 GREEN
3 BLUE
4 C-SYNC
5 NOT CONNECTED
6 NOT CONNECTED
7 NOT CONNECTED
8 NOT CONNECTED
4
1
6
2
8
5
3
7
RGB Input DIN Configuration from Composite Video
Video Source Composite In
To lgnition Fuse
+12V
Ground(To Chassis)
To Remote Onput IR Remote Output from RGB
Video Source from RGB Output of RGB Input DIN Connector
NAX9500E speaker(-) speaker(+)
Dimmer Lead
NAX
VS718
Video Out
NOTE:
*These CCE-001 adapt IR of NAX and/or VS718 to VMA633! Never use
IR connection without CCE-001!
4
OWNER’S MANUAL
T
ROUBLESHOOTING:
S ymptom
C ause
S olution
System does not work
The screen dark.
Fuse is blown.
Power wires are not connected.
The brightness is adjusted too low.
Usage conditions are poor.
Replace external fuse with the same value.
Check the wire connections and
Connect it properly.
Check that the brightness is proper- ly adjusted, if not adjust it properly.
This may happen if the temperature in the vehicle is below –1°C (30°F) or above 45°C (113°F). Check again when the temperature is between
-1°C (30°F) and 45°C (113°F)
S
PECIFICATION:
G
ENERAL
S
PECIFICATIONS:
Power Requirement:
Power Consumption:
Weight
Dimensions (w x h x d):
Included Parts
+12 Volts DC (9-16 Volts DC)
9 watts, Power On
0.8 amps (800mA)
0.5 kg (1.1 lb)
167 x 121 x 29 mm (6-1/2 x 4-7/10 x 1-3/10 in.)
LCD Monitor
3.5 mm Male to Male IR extension cable (5m)
2-pin Molex Power connector
CCE-001 IR adapter for NAX9500E and/or VS718
Mounting bracket
Speaker extension cable (5m)
M
ONITOR
S
PECIFICATIONS:
Display Type:
Screen Size:
Colour TFT Active Matrix LCD
6.5” (Panel Dimensions 144.4 x 80.3 mm)
Pixels:
Screen Resolution:
Video Input Level(RCA)
RGB Input Level
1200 x 234
280,800 dots
1.0 volts peak to peak, NTSC
0.75 volts peak to peak, TTL
5
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement