Cisco Session Manager Edition 8.5, 8.5, Enterprise Edition 1.4, 1002, 7961, 7960, 2010, 2008, 2008, 2008 R2, Session Manager Edition Application Note

Below you will find brief information for Unified Communications Manager Session Manager Edition 8.5, Unified Communications Manager 8.5, Unified Border Element Enterprise Edition 1.4. This document covers the basic steps and configurations for connectivity between Cisco Unified Communications Manager Session Manager Edition (Cisco UCM SME) 8.5(1) via Direct SIP to Microsoft Lync 2010 server using Microsoft Mediation Server, and via SIP connection to a Cisco Unified Communications Manager (Cisco UCM) 8.5(1), and SIP connection to simulated Service Provider (SP) using Cisco Unified Border Element (Cisco UBE) 1.4. The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability between the different leaf nodes (Microsoft Lync 2010, Cisco UCM and Cisco UBE/SP) via the Cisco UCM SME.

PDF

Document

Microsoft Lync 2010 using SIP via Cisco Unified Communications

Manager- Session Manager Edition 8.5 to Cisco Unified

Communications Manager 8.5 and Cisco Unified Border Element

(Enterprise Edition) 1.4 on ASR to Service Provider

Se pte mbe r 28, 2011 - Initial Ve rsion

Table of Contents

Introduction ............................................................................................................................................................................. 3

Network T opology ................................................................................................................................................................... 4

Capabilities.............................................................................................................................................................................. 5

Limitations .............................................................................................................................................................................. 5

Features Supported................................................................................................................................................................... 7

Features Not Supported and Not T ested .................................................................................................................................... 7

System Components................................................................................................................................................................. 8

Hardware Requirements ...................................................................................................................................................... 8

Software Re quirements ....................................................................................................................................................... 8

System Configuration............................................................................................................................................................... 9

Configuring the Microsoft LYNC 2010 Server Standard Edition........................................................................................... 9

Domain Name System Configuration ...............................................................................................................................10

Forward Lookup Zone .....................................................................................................................................................11

Reverse Lookup Zones Configuration ..............................................................................................................................12

SRV Records Configuration.............................................................................................................................................13

Lync Server 2010 Site Topology Overview ......................................................................................................................16

Mediation Server Overview .............................................................................................................................................19

Active Directory User Configuration................................................................................................................................23

Lync Server 2010 Configuration ......................................................................................................................................27

Voice Routing Configuration ...........................................................................................................................................30

Lync 2010 Server Management Shell Commands .............................................................................................................34

Microsoft LYNC 2010 Enterprise Voice Client Configuration .............................................................................................36

Cisco Unified Communications Manager- Session Manager Edition Configurations.............................................................43

Cisco Unified Communications Manager- Session Manager Edition – Software release.....................................................43

Cisco Unified Communications Manager-Session Manager Edition-Region Configurations...............................................44

Cisco Unified Communications Manager – Session Manager Edition – Device Pools ........................................................45

Cisco Unified Communications Manager – Session Manager Edition – Device Pool Configurations G711 .........................46

Cisco Unified Communications Manager – Session Manager Edition – Device Pool Configurations G711 .........................47

Cisco Unified Communications Manager – Session Manager Edition – Device Pool Configurations-G729.........................48

Cisco Unified Communications Manager – Session manager Edition - Media T ermination Points Configurations ..............50

Cisco Unified Communications Manager – Session manager Edition – Transcoder Configuration......................................52

Cisco Unified Communications Manager – Session Manager Edition – Media Resource Groups configurations .................53

Cisco Unified Communications Manager – Session Manager Edition – Media Resource Group Lists configurations ..........55

Cisco Unified Communications Manager –Session Manager Edition – Route Patterns .......................................................58

Cisco UCM- SME Ro ute list for PST N (CUBE) access .....................................................................................................69

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

EDCS-1093248 Initial Version

Page 1 of 147

Application Note

SME Ro ute Group for PST N T runk Access......................................................................................................................70

Cisco UCM- SME SIP Trunks: .........................................................................................................................................71

SME SIP trunk to Service Provider via ASR CU BE..........................................................................................................72

Cisco UCM- SME SIP trunk to Cisco UCM ......................................................................................................................75

Cisco UCM- SME SIP trunk to Microsoft LYNC 2010 Server Standard Edition.................................................................78

Configuring the Cisco Unified Communications Manager ...................................................................................................81

Cisco UCM Software release ...........................................................................................................................................81

Cisco UCM Re gions Configurations ................................................................................................................................82

Cisco UCM Re gions Configurations – G711 Region ........................................................................................................83

Cisco UCM Re gion Configurations – G729 Region ..........................................................................................................84

Cisco UCM Device Pool for G711 ...................................................................................................................................86

Cisco UCM Device Pool for G729 ...................................................................................................................................88

Cisco UCM Me dia Reso urce Group .................................................................................................................................94

Cisco UCM Me dia Reso urce Group List ..........................................................................................................................95

Cisco UCM Ro ute Pattern Configuration..........................................................................................................................96

Cisco UCM SIP trunks configurations............................................................................................................................103

SIP T runk Configuration for the Session Manager Edition ..............................................................................................104

SCCP Phone configurations on the Cisco UCM..............................................................................................................110

DN Configuration for SCCP Phone ................................................................................................................................116

SIP Phone configurations on the Cisco UCM..................................................................................................................120

DN Configuration for the SIP Phone ..............................................................................................................................123

Cisco IO S Gateway Configurations ..................................................................................................................................126

Cisco Unified Border Element Configuration on the ASR ...............................................................................................126

IOS MT P and Hardware CFB Configuration ..................................................................................................................134

Fax Gateway Configuration ...........................................................................................................................................141

Acronyms .............................................................................................................................................................................145

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 2 of 147

Application Note

Introduction



This application note describes the necessary steps and configurations for connectivity between Cisco Unified

Communications Manager-Session Manager Edition (Cisco UCM-SME) 8.5(1) via Direct SIP to Microsoft Lync 2010 server using Microsoft Mediation Server, and via SIP connection to a Cisco Unified Communications Manager (Cisco

UCM) 8.5(1), and SIP connection to simulated Service Provider (SP) using Cisco Unified Border Element (Cisco UBE)

1.4. The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability between the different leaf nodes (Microsoft Lync 2010, Cisco UCM and Cisco UBE/SP) via the Cisco UCM-SME.



Features tested are basic call, 3-way (ad-hoc) conference, call transfer (attended and unattended), call forward (all, busy and no answer), hold/resume, DT MF inter-working and voice mail. T his test setup also includes a connection to a simulated service provider using SIP trunks. Cisco UBE is use d as a session border controller (SBC), providing demarcation, security, and inter-working services between the customer’s private network and the service provider’s SIP network. Voice mail was tested for Cisco UCM users with mailboxes registered to Unity Connection via a Direct SIP trunk from Cisco UCM-SME. Fax could not be tested (see limitations section).



During testing, a Cisco ASR 1002 router was used as Cisco UBE, however other Cisco voic e gateways, such as the 3900 series or AS5400 XM can be used and the decision to choose what Cisco gateway model to use is left to the customer.

The customer should choose a Cisco IOS gateway model ba sed on the capabilities and the capacity that will be re quire d base d on the planned network deployment. Here is a list of Cisco IOS products capable of running Cisco UBE.



Cisco A SR 1000 Series A ggregation Services Router

Cisco 3900 Series Integrated Services Routers

Cisco 2900 Series Integrated Services Routers

Cisco 3800 Series Integrated Services Routers

Cisco 2800 Series Integrated Services Routers

Cisco A S5400XM Universal Gateway

Cisco A S5350XM Universal Gateway



If additional guidance on the Cisco UBE is needed, please refer to the Cisco UBE section on the Cisco Interoperability

Portal ( www.cisco.com/go/interoperability ).



This configuration was tested to simulated service provider. Results may vary based on service provider being use d.



Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 3 of 147

Application Note

Network Topology

Microsoft

Mediation Server

Mediation Server Pool

172.20.117.130

SIP

Microsoft LYNC

2010Standard Edition

Server with SQL

172.20.117.120

Service Provider or

Simulated Service

Provider

SIP

Phone SP1 Phone SP1

CPE to CPE

CPE to PSTN (SP)

Cisco UBE 1.4

Cisco Unity

Connection Server

Cisco UCM-SME

SIP

Rel. 8.5(1)

Cisco ISR

– for IOS

MTP requirement

SIP

Active Directory/

Domain Controller/DNS

172.20.117.120

Intranet IP Cloud

SIP Trunk

Laptop

Enterprise Voice

Client

+14089333473

Enterprise Voice

+14089333474

Cisco UCM

Rel. 8.5(1)

Laptop

Enterprise Voice

+14084243475

Phone C1

Phone C2

FAX C3

Figure 1. Basic Call Setup

Note: As of Cisco UCM-SME Rel. 8.5, for SIP trunk connection re quir ing Early Offer function, configuration is made under the SIP Profile configuration associated w ith the SIP trunk. Pr ior to Release 8.5, netw ork administrators w ere forced to configure SIP trunks on Cisco UCM-SME to send early offer by using/allocating Media Ter mination Point. In

Cisco UCM-SME Rel. 8.5, the Media Ter mination Point ( MTP) chec kbox under the SIP Trunk configuration page no longer needs to be chec ked to implement ear ly offer function.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 4 of 147

Application Note

Capabilities



Voice calls includin g supplementary services can be successfully established between endpoints controlled by the

Microsoft Lync 2010 and endpoints controlled by the Cisco UCM.



Voice calls includin g supplementary services can be successfully established between endpoints controlled by the

Microsoft Lync 2010 and the PST N, using Cisco UBE as a se ssion border controller.



IOS MT Ps and transcoders registered to the Cisco UCM-SME can be employed to offer G729 as originating codec option.

Limitations



These are the known limitations, caveats, or integration issues.



Microsoft Lync does not support sending or receiving calling and connected name in certain scenarios (like call forward and call-transfer). Cisco UCM sends its calling name and number to Microsoft Lync Mediation Server, but the

Lync only displays the calling number and no name is displayed.

Microsoft Lync 2010 does not provide music on hold (MoH) capability by default except on Microsoft Attendant

Console. MoH needs to be enabled usin g CLI through the Lync Management Shell.



Microsoft Lync 2010 displays presence information in the Enterprise Voice client only for other Enterprise voice users configured in the Active Directory and Enterprise voice enabled.



For Microsoft Lync 2010, the Enterprise Voice client cannot be configured for Call Fo rward Busy. As an option the

Enterprise Voice client allows the user to receive a notification of an incoming call during an active call and “redirect” the incoming call to a destination of the user’s choice.



Calling and connected number updates during call-forwar d and call-transfer scenarios are not fully supported due to

SIP UPDATE messages not being interoperable between the systems. For e.g. when a Lync user transfers a PBX call to another PBX user, the local PBX phone will still show connected to the f irst Lync user.



Cisco SIP Phones do not send out Comfort Noise payload 13 in the m line of the SDP to indicate support for Comfort

Noise as per RFC 3389 and as a result Microsoft doesn't send out SID frames when call is muted on Microsoft side.



Microsoft Lync 2010 sends its SIP URI @domain in the INVITE, while setting up a conference call, as a result the caller ID will not be displayed properly on the far end.



The Media Bypass capability introduced in Microsoft Lync 2010 requires all media through a SIP trunk integration to originate on a single IP address. For this Microsoft requirement in a Lync to Cisco UCM inter-working, media termination point is required on the SIP trunk for Media Bypass to work.



When the Enterprise Voice client, initiates a conference call, the conference call does not end when the initiator hangs up, but only after all parties hang up. Additionally for the Enterprise Voice users on the conference call, the session is not dropped and they can rejoin the conference, unless they close the window pop -up for the call, referred t o as the toast.

Media Bypass is a mandatory requirement if customers want to collocate the Mediation Server role with the Front -End server role. Important: According to the Microsoft Lync Planning Tool collocatio n should only be use d if the IP -PBX and/or the voice gateways support Media Bypass and Enterprise voice is not considered mission critical to the organization.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 5 of 147

Application Note



Media Bypass works as long as an MTP is required on the SIP trunk. T he need for an MTP is due to the following:

1. Lync supports Media Bypass with early offer, but does not support re-invite without SDP

Lync doesn’t support Media Bypass with delayed offer

3. Because of #1, hold/resume, transfer, forward, etc won’t work without an MTP.

RFC 3261 sections 13.2.1 and 14.1 make a strong case that Lync’s behavior (#1 above) isn’t compliant with

MUST aspects of the SIP standard. Including the MTP enables standards-compliant interoperability in light of the Lync implementation.



Microsoft Lync 2010 only supports T CP transport to carry SIP messages. If UDP is required CUBE can be use d to perform the conversion.



Microsoft Lync 2010 only supports G711 ulaw or alaw on the outside interface. If G729 is required CU BE or transcoder registered to SME can perform the t ranscoding function.



Microsoft Lync 2010 does not support G711 Fax Passthrough.



Fax T.38 to Service provider is not tested. Service Provider used for this test does not support Fax T.38 switchover.



On Lync Mediation Server, RT CP is set to disable d, as RT CP is an end point specific configuration and not all Cisco phones support RT CP. Phones like 7970, 7962, and 9971 have this support and this can be enabled under Phone

Configuration – Product Specific Configuration Layout.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 6 of 147

Application Note

Features Supported



Basic calls



Digits T ranslation



Intra-site call conferencing



Call T ransfer-Attended and Unattended (See Limitations section for details)



Hold and resume



Call forward – Unconditional, Busy and No reply (See Limitations section for details.)



Sim ultaneous calls



Inbound/Outboun d Basic calls ( G711 u-law and a-la w) (RFC 3261)



Call Forwar d (RFC 3261)



Conference calls



DT MF (RFC 2833)



Options T esting



Reliable 1XX Provisional Response or PRACK (RFC 3262)



Early Media (RFC 3261)



Call hold and resume using Offer/Answer Model (RFC 3264)



ISDN Mapping

Features Not Supported and Not Tested



T .38 FAX Relay was not tested. - T he Service provider used for this test does not support T .38 FAX.



Blind call transfers



Comfort noise is not supported



Decline a call (CUCM phones divert calls to voicemail, instead of declining the call)

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 7 of 147

Application Note

System Components

Hardw are Requirem ents



Cisco MCS 7835 Unified Communications Manager



Cisco MCS 7835 Session Manager Edition



Cisco 3825 voice gateway



Cisco A SR1K router



T wo Cisco Unified IP phone 7961 configured as SCCP phones



One Cisco Unified IP phone 7960 configured as SIP phones



Three DELL notebooks running LYNC clients

Softw are Requirements

The following software is required:



Cisco Unified Communications Manager Release 8.5



Cisco UCM- Session Manager Edition Release 8.5



Microsoft Lync Server 2010 Standard Edition, Windows Server 2008 R2 x64 Enterprise Edition OS



Windows Active Directory/DNS/Cert Server, Windows Server 2008 R2 x64 Enterprise Edition OS



Backend Database: Windows SQL Server 2008 Enterprise Edition, Windows Server 2008 x64 Enterprise Edition OS



Microsoft Lync 2010 (build 4.0.7577.4)



Cisco A SR1K rou ter Release 3.3.1.S

IMPORTANT:

Microsoft Lync Server, Mediation Server and Lync Communicator all need to run through the Microsoft Update webs ite to have the latest updates installed for this integration to work correctly.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 8 of 147

Application Note

System Configuration

This section contains configuration menus and commands and describes configuration sequences and tasks.

Configuring the Microsoft LYNC 2010 Server Standard Edition

The look and feel between Lync and the previous versions are different (refer to the captured screenshots) and tools like Lyn c planning tool, T opology builder, Lync Server Control Panel, Lync Management Shell are added. T he main differences wer e seen during the deployment of the Lync environment itself and how its own components connected to each other. T hose differences include, the use of 64-bit servers for each component (refer to Software Requirements section), the need for an interface mo dule

(automatically downloaded during installation) on the Front End Servers to enable communication with SQL 2008 (refer to the

Microsoft deployment and installation guides for more information, links included below), and finally the configuration of th e certificate authority server (refer to the Microsoft deployment and installation guide s for more information, links included below).

For Cisco docum entation guides including release notes, compatibility m atrix, deploym ent, installation guides etc, go to: http://www.cisco.com /en/US/docs/voice_ip_com m /cucm /srnd/8x/uc8x.htm l http://www.cisco.com /en/US/docs/voice_ip_com m /cucm /docguide/8_5_1/dg851.htm l

For Microsoft deployment and installation guide s, go to: http://technet.microsoft.com/en-us/library/gg293124.aspx

http://technet.microsoft.com/en-us/library/gg398616.aspx

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 9 of 147

Application Note

Configuration Steps:

1. Domain Name System Configuration

2. Front End Server/Pool Configuration

3. Mediation Server Configuration

4. User Configuration

5. Microsoft Lync 2010 Configuration

Please refer to the Microsoft Lync Standard Edition Server deployment guide for setup details. Only interoperability related configurations are included in this document.

Domain Name System Configuration

Start > Adm inistrative Tools > DNS

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 10 of 147

Forw ard Lookup Z one

Application Note

Host A records adde d for Lync Front End server, Active Directory/DNS and Mediation Server.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 11 of 147

Reverse Lookup Zones Configuration

Application Note

PTR Records added for the Lync server and Active Directory.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 12 of 147

SRV Records Configuration

Application Note

SRV Record a dde d for SIP domain service offered by the Lync pool (for Automatic Client Sign-in).

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 13 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 14 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 15 of 147

Lync Server 2010 Site Topology Overview

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 16 of 147

Application Note

SME must be added in T opology Builder as a PST N gateway. PST N gateway is the generic term to refer to IP-PBX and other gateway devices. T he topology must be published to Central Management store. After the PST N gateway (that is,

SME) is added to the topology, it appears in the Lync Server Control Panel. The first thing to do is to add a trunk to the IP -

PBX (that is, SME)

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 17 of 147

Application Note

Listening port of the SME is left to default 5060.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 18 of 147

Mediation Server Overview

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 19 of 147

Application Note

LYNC Front End server configuration with FQDN

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 20 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 21 of 147

Application Note

PST N Gateway associated with the Mediation Pool

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 22 of 147

Active Directory User Configuration

Create users from Front End Server by accessing the Active Directory Users and Computers window

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 23 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 24 of 147

Application Note

SME

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 25 of 147

Application Note

Computers on the Activ Directory running LYNC clients

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 26 of 147

Application Note

Lync Server 2010 Configuration

Lync Server configuration can be done in a couple of ways—through the Microsoft Lync Server Control Panel or through Lync

Server Management Shell. For the purposes of configuring a direct SIP connection with CUCM, we will illustrate the configuration by using the Lync Server Control Panel and T opology Builder.

User Configuration from Control Panel

Start > All Pr ograms > Microsoft Lync Server 2010 > Lync Server Control Panel

To add users got to Home > Enable users for Lync Server and then go to Users > Add and then do a find as show n below .

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 27 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 28 of 147

Application Note

In Lync Server, best practice is to use a dial plan that is based on the E.164 standard. This allows easier routing and troubleshooting as well as a scalable model for growth. It is best practices to represent numbers in an E.164 format (Externa l

DIDs as well as internal extensions).

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 29 of 147

Voice Routing Configuration

Application Note

Lync Server normalizes all outbound calls as E.164. T his allows uniform routing that scales globally across the Lync Server deployment. Phone numbers are normalized to E.164 by normalization rules in this case the rule 4dig-ext. Normalization rules are added in the Dial Plan tab.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 30 of 147

Application Note

PST N usage is associated on the Voice Policy. Calling features are selected in Voice policy tab. New user policy is created to dial to the SME.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 31 of 147

Application Note

Route to SME is associated with the PST N gateway(SME in our case) here.

After the trunk is configured, routes can be configured to route CUCM extensions to the trunk to SME. If PST N connectivity is configured through SME, calls to PST N from Lync 2010 can be routed to SME through the trunk.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 32 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 33 of 147

Application Note

Lync 2010 Server Mana gement Shell Commands

Lync Se rve r/Client Address Book Updating

With the default server/client settings, the Address Book is not updated right away. T o ensure that the Address Book is updat ed with the latest users added to the Active Directory and their configurations, force the update on the server side. T hen force the

Lync 2010 Client to pull down the latest files to update its local GalContacts.db file.

On Lync Server 2010, enter the following command in the Lync Server Management Shell:

Update-CsAddressBook

This triggers the Lync Server to synchronize current Active Directory information in the SQL database into the downloadable client and device address book files. Wait 5 minutes for this process to complete.

On Lync Client 2010, execute the following command from the Windows Command Prompt run as an administrator:

reg add HKLM\Software \Policies\Microsoft\Communicator /v GalDownloadInitialDelay /t REG_DWO RD /d 0 /f

Setting this value to 0 will force Lync to immediately download the address book inst ead of randomly selecting a time to check the server.

On Lync Client 2010, if the GalContacts.db and GalContacts.db.idx files already exist, delete them from the user’s profile directory (directory location may vary depending on your Client OS). Make sure you exit and restart the Lync Client, after log in you should see a new set of files downloaded, and you should see the latest updated users appear during a search for contacts.

Lync 2010 Se rve r draining mode

Stop-CsWindowsService -Graceful rtcmedsrv

Some Lync2010 use ful commands

Get-CsTrunkConfiguration

Set-CsTrunkConfiguration

Get-CsMediaConfiguration

Set-CsMediaConfiguration

PS C:\Users\administrator.OCS2010> Get-CsTrunkConfiguration

Identity : Global

OutboundTranslationRulesList : {}

SipResponseCodeTranslationRulesList : {}

Description :

ConcentratedTopology : True

EnableBypass : False

EnableMobileTrunkSupport : False

EnableReferSupport : True

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 34 of 147

EnableSessionTimer : False

EnableSignalBoost : False

MaxEarlyDialogs : 20

RemovePlusFromUri : False

RTCPActiveCalls : True

RTCPCallsOnHold : True

SRTPMode : Required

EnablePIDFLOSupport : False

PS C:\Users\administrator.OCS2010> Get-CsMediaConfiguration

Identity : Global

EnableQoS : False

EncryptionLevel : RequireEncryption

EnableSiren : False

MaxVideoRateAllowed : VGA600K

Identity : Site:lab

EnableQoS : False

EncryptionLevel : RequireEncryption

EnableSiren : False

MaxVideoRateAllowed : VGA600K

Lync2010 - e nable music on hold:

set-csclientpolicy -EnableClientMusicOnHold $TRUE

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 35 of 147

Microsoft LYNC 2010 Enterprise Voice Client Configuration

Navigation: Choose T ools  Options and enter the sign-in information.

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 36 of 147

Application Note

Click Advanced button to select the Advanced Connection Settings.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 37 of 147

Application Note

If there are DNS entries for this Microsoft Lync, automatic configuration can be used if not select manual configuration.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 38 of 147

After signing add contacts

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 39 of 147

Personal Options and Audio Settings

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 40 of 147

LYNC Dialpad

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 41 of 147

Call Forwar ding Configurations

Application Note

All call forward settings are selected in this tab. You can turn on/off the call forwarding settings and also select for phon es to simultaneously ring.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 42 of 147

Application Note

Cisco Unified Comm unications Manager- Session Manager Edition Configurations

UC deployments using Unified CM Session Manager Edition are a variation on the Multi-site Distributed Call Processing deployment model and are typically used where large numbers of UC end systems need to be interconnected via a single U C system - i.e. T he Unified CM Se ssion Manager. A deployment using Cisco Unified CM Session Manager Edition is essentially a

Unified CM cluster with trunk interfaces only (although IP endpoints are also allowed if required). It allows aggregation of multiple Unified Communications systems, referred to as leaf systems. UC SME is deployed to create and manager centralized dialplan, provide centralized PST N access, aggregate PBX trunks, interconnect and interoperate across different protocols, lo ad balance inbound and outbound calls.

Note: Cisco Session Manager Edition is set to manage dialplan as a best practice. T he Cisco Unified Border Element – Enterprise edition passes all the digits over to the Session Manager Edition and the Session Manager routes the c alls to the leaf nodes i.e.,

Cisco Unified Communications Manager and Microsoft LYNC 2010 Server.

Cisco Unified Communications Manager- Session Manager Edition

– Softw are release

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 43 of 147

Cisco Unified Communications Manager-Session Manager Edition-Region Configurations

Application Note

Region configurations are used to determine the codecs used by the endpoint within the region and across the region.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 44 of 147

Cisco Unified Communications Manager

– Session Manager Edition – Device Pools

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 45 of 147

Application Note

Cisco Unified Communications Manager

– Session Manager Edition – Device Pool Configurations G711

Region is associated with a device pool which is assigne d to the endpoint or a trunk.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 46 of 147

Application Note

Cisco Unified Communications Manager

– Session Manager Edition – Device Pool Configurations G711

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 47 of 147

Application Note

Cisco Unified Communications Manager

– Session Manager Edition – Device Pool Configurations-G729

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 48 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 49 of 147

Application Note

Cisco Unified Communications Manager

– Session manager Edition - Media Ter mination Points Configurations

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 50 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 51 of 147

Cisco Unified Communications Manager

– Session manager Edition – Transcoder Configuration

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 52 of 147

Application Note

Cisco Unified Communications Manager

– Session Manager Edition – Media Resource Groups configurations

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 53 of 147

MRG for LYNC MRGL

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 54 of 147

Application Note

Cisco Unified Communications Manager

– Session Manager Edition – Media Resource Group Lists configurations

LYNC will need a separate MRGL to force MTP based early offer from the SME

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 55 of 147

MRGL to be associated with SIP trunks except LYNC trunk

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 56 of 147

MRGL to be associated with SIP trunk connecting Microsoft LYNC 2010 server

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 57 of 147

Cisco Unified Communications Manager

–Session Manager Edition – Route Patterns

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 58 of 147

Route Pattern to the Microsoft LYNC 2010 server

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 59 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 60 of 147

Route Pattern to the Cisco Unified Communications Manager 8.5 ( Leaf node)

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 61 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 62 of 147

Route Pattern to route calls to the LYNC server

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 63 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 64 of 147

Route Pattern to Service Provider

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 65 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 66 of 147

International Route Pattern

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 67 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 68 of 147

Cisco UCM-SME Route list for PSTN (CUBE) access

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 69 of 147

SME Route Group for PSTN Trunk Access

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 70 of 147

Cisco UCM-SME SIP Trunks:

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 71 of 147

SME SIP trunk to Service Pr ovider via ASR CUBE

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 72 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 73 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 74 of 147

Cisco UCM-SME SIP trunk to Cisco UCM

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 75 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 76 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 77 of 147

Cisco UCM-SME SIP trunk to Microsoft LYNC 2010 Server Standard Edition

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 78 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 79 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 80 of 147

Configuring the Cisco Unified Comm unications Manager

Cisco UCM Softw are release

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 81 of 147

Cisco UCM Regio ns Configurations

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 82 of 147

Cisco UCM Regio ns Configurations

– G711 Region

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 83 of 147

Cisco UCM Regio n Configurations

– G729 Region

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 84 of 147

Cisco UCM Device Pool

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 85 of 147

Application Note

Cisco UCM Dev ice Pool for G711

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 86 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 87 of 147

Cisco UCM Dev ice Pool for G729

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 88 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 89 of 147

Cisco UCM Me dia T ermination Point Configuration

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 90 of 147

Cisco UCM Conference Bridge Configurations

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 91 of 147

Software Conference Bridge

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 92 of 147

Hardware Conference Bridge

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 93 of 147

Cisco UCM Media Resource Group

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 94 of 147

Cisco UCM Media Resource Group List

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 95 of 147

Cisco UCM Route Pattern Configuration

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 96 of 147

PST N Route Pattern

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 97 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 98 of 147

International Route Pattern

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 99 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 100 of 147

Fax Route Pattern

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 101 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 102 of 147

Cisco UCM SIP trunks configurations

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 103 of 147

SIP Trunk Configuration for the Session Manager Edition

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 104 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 105 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 106 of 147

SIP Trunk Configuration for the Fax Gateway

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 107 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 108 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 109 of 147

SCCP Phone configurations on the Cisco UCM

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 110 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 111 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 112 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 113 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 114 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 115 of 147

DN Configuration for SCCP Phone

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 116 of 147

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 117 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 118 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 119 of 147

SIP Phone configurations on the Cisco UCM

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 120 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 121 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 122 of 147

DN Configuration for the SIP Phone

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 123 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 124 of 147

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 125 of 147

Application Note

Cisco IOS Gatew ay Configurations

Cisco Unified Border Element Configuration on the ASR

CUBE-A SR1K_Vz_151#show ver

Cisco IO S Software, IOS-XE Software (PPC_LINUX_IOSD-AD VENT ERPRISEK9-M), Version 15.1(2)S1, RELEASE

SO FT WARE (fc2)

T echnical Support: http://www.cisco.com/techsupport

Compiled Wed 01-Jun-11 04:09 by mcpre

All rights reserved. Certain components of Cisco IOS-XE software are licensed un der the GNU General Public License ("GPL") Version 2.0. T he software code licensed under GPL Version 2.0 is free software that comes with ABSOLUT ELY NO WARRANT Y. You can redistribute and/or modify such

GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software.

ROM: IO S-XE ROMMON

CUBE-A SR1K_Vz_151 uptime is 5 weeks, 2 days, 19 hours, 48 minutes

Uptime for this control processor is 5 weeks, 2 days, 19 hours, 50 minutes

System returned to ROM by reload

System image file is "boot flash:asr1000rp1-adventerprisek9.03.03.01.S.151-2.S1.bin"

Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to [email protected].

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 126 of 147

Application Note

cisco ASR1002 (2RU) processor with 1703423K/6147K bytes of memory.

4 Giga bit Ethernet interfaces

32768K bytes of non-volatile configuration memory.

4194304K bytes of physical memory.

7798783K bytes of eUSB flash at bootflash:.

Configuration register is 0x2102

CUBE-A SR1K_Vz_151#show run

Building configuration...

Current configuration : 8863 bytes

! Last configuration change at 12:34:31 UT C Fri Sep 9 2011

! version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no platform punt-keepalive disable-kernel-core

! hostname CUBE-ASR1K_Vz_151

! boot -start-marker boot system bootflash:asr1000rp1-adventerprisek9.03.03.01.S.151-2.S1.bin boot -end-marker

! vrf definition Mgmt -intf

address-family ipv4

exit-address-family

address-family ipv6

exit-address-family

! logging buffered 20000000 logging console errors enable password cisco

! no aaa new-model

! ipc zone default

association 1

no shutdown

! ip source-route

! ip domain name ciscolab.globalipcom.com ip name-server 172.30.218.36

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 127 of 147

Application Note

! multilink bundle-name authenticated

! voice service voip

allow-connections sip to sip

no supplementary-service sip refer

redirect ip2ip

sip

header-passing error-passthru

asserted-id pai

localhost dns:gw1.ciscolab.glo balipcom.com

early-offer forced

midcall-signaling passthru

privacy-policy passthru

g729 annexb-all

no call service stop

! voice class sip-profiles 1

response ANY sip-header Allow-Header modify "invite, options, bye, cancel, ack, prack, update, refer, subscribe, notify, info, register" "invite, bye, cancel, ack, prack, subscribe, notify, info, register"

response 183 sip-header Allow-Header modify "ACK, BYE, CACEL, INFO, INVIT E, OPTIONS, PRACK, REFE R, NOT IFY"

"ACK, BYE, CANCEL, INFO, IN VIT E, PRACK, REFER, NOT IFY"

response ANY sip-header Allow-Header modify "INVITE, OPT IONS, BYE, CACEL, ACK, PRACK, UPDAT E, REFER,

SU BSCRIBE, NOT IFY, INFO, REGI ST ER" "INVIT E, BYE, CACEL, ACK, PRACK, SU BSCRIBE, NOT IFY, INFO,

RE GI ST ER"

! voice class sip-profiles 2

request REINVIT E sdp-header Audio-Attribute modify "inactive" "sendrecv"

request REINVIT E sdp-header Audio-Attribute modify "sendonly" "sendrecv"

request ACK sdp-header Audio-Attribute modify "sendonly" "sendrecv"

response 200 sdp-header Audio-Attribute modify "sendonly" "sendrecv"

! voice translation-rule 1

rule 1 /71/ /1\1/

! voice translation-rule 2

rule 1 /^84089550468/ /14089550468/

! voice translation-rule 7

rule 1 /71/ /1\1/

! voice translation-profile Outgoing-Fax-G711

translate called 1

! voice translation-profile RICUBcallingnum

translate calling 2

translate called 2

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 128 of 147

Application Note

! redundancy

mode none

! no ip ftp passive ip ftp username cisco ip ftp password cisco

! interface Giga bitEthernet0/0/0

ip address 172.20.110.151 255.255.255.0

negotiation auto

! interface Giga bitEthernet0/0/1

no ip address

standby delay minimum 30 reload 60

standby version 2

standby 1 priority 50

standby 1 track 1 decrement 10

shutdown

negotiation auto

bfd interval 500 min_rx 500 multiplier 3

! interface Giga bitEthernet0/0/2

no ip address

shutdown

negotiation auto

! interface Giga bitEthernet0/0/3

no ip address

shutdown

negotiation auto

! interface Giga bitEthernet0

vrf forwarding Mgmt -intf

no ip address

shutdown

negotiation auto

! ip default -gateway 172.20.110.1 ip forward-protocol nd

! no ip http server no ip http secure-server ip route 172.20.0.0 255.255.0.0 172.20.110.1 ip route 172.30.218.0 255.255.255.0 172.20.110.150

! logging e sm config

! tftp-server flash:

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 129 of 147

Application Note

! control-plane

! dial-peer voice 9000 voip

description to SP facing

destination-pattern ..........

session protocol sipv2

session target sip-server

session transport udp

voice-class sip asserted-id pai

dtmf-relay rtp-nte

fax protocol pass-through g711ulaw

! dial-peer voice 9001 voip

description Incoming to SME - SME facing

destination-pattern 408933....

session protocol sipv2

session target ipv4:172.20.8.41

session transport tcp

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

no vad

! dial-peer voice 577 voip

description Outbound to Fax Machines

destination-pattern 408577....

session protocol sipv2

session target sip-server

session transport udp

incoming called-number 408577....

codec g711ulaw

fax protocol pass-through g711ulaw

! dial-peer voice 3470 voip

description To Fax Machines towards SME

shutdown

destination-pattern 40893334..

session protocol sipv2

session target ipv4:172.20.8.41

session transport udp

incoming called-number 40893334..

codec g711ulaw

fax protocol pass-through g711ulaw

Outbound dialpeer towards service provider

Outbound dialpeer towards SME. CUBE sends all the 10 digits to SME for centralized dialplan

resolution

Outbound dialpeer towards fax machine gateway behind the SME (refer topology diagram for details)

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 130 of 147

Application Note

dial-peer voice 408 voip

description To SP 7-digit dialing - SP facing

destination-pattern .......

session protocol sipv2

session target sip-server

session transport udp

voice-class sip asserted-id pai

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

! dial-peer voice 9003 voip

description Fax calls using G.711u - SP facing

translation-profile outgoing Outgoing-Fax-G711

destination-pattern 71..........

session protocol sipv2

session target sip-server

voice-class sip early-offer forced

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

! dial-peer voice 9900 voip

description to SP - SME facing

session protocol sipv2

session transport udp

incoming called-number ..........

voice-class sip asserted-id pai

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

no vad

! dial-peer voice 9901 voip

description Incoming to SME - SP facing

session protocol sipv2

session transport tcp

incoming called-number 408933....

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

no vad

! dial-peer voice 4408 voip

description To SP 7-digit dialing - SME facing

session protocol sipv2

session transport udp

incoming called-number .......

Dialpeer for 7 digit dialing towards the SP

Dialpeer for Fax calls using G.711u - SP facing

Incoming dialpeer SME facing

Incoming dialpeer SP facing

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 131 of 147

Application Note

dtmf-relay rtp-nte

fax protocol pass-through g711ulaw

! dial-peer voice 9004 voip

description To SP - International calls - SP facing

destination-pattern 011T

session protocol sipv2

session target sip-server

session transport udp

voice-class sip early-offer forced

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

! dial-peer voice 9904 voip

description To SP International calls - SME facing

session protocol sipv2

session target sip-server

session transport udp

incoming called-number 011T

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

! dial-peer voice 1800 voip

destination-pattern 1800.......

session prot ocol sipv2

session target sip-server

session transport udp

voice-class sip asserted-id pai

dtmf-relay rtp-nte

codec g711ulaw

fax protocol pass-through g711ulaw

no vad

! dial-peer voice 7 voip

session protocol sipv2

session target sip-server

session transport udp

incoming called-number 71….......

voice-class sip asserted-id pai

dtmf-relay rtp-nte

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none

no vad sip-ua

set pstn-cause 1 sip-status 503

International dialing dialpeer towards the SP

Incoming dialpeer for international calls from the SME

Toll free dialing dialpeer

Incoming fax dialpeer SME facing

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 132 of 147

set pstn-cause 102 sip-status 503

retry invite 2

retry bye 2

retry cancel 2

timers trying 1000

sip-server ipv4:172.30.218.49:5147

g729-annexb override

! line con 0

password cisco

stopbits 1 line aux 0

stopbits 1 line vty 0 4

password cisco

! end

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 133 of 147

Application Note

IOS MTP and Hardw are CFB Configuration

MSFT -GW2#show ver

Cisco IO S Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(3)T 1, RELEASE SOFT WARE (fc2)

T echnical Support: http://www.cisco.com/techsupport

Compiled Sun 27-Mar-11 07:36 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFT WARE (fc1)

MSFT -GW2 uptime is 3 weeks, 6 days, 1 hour, 49 minutes

System returned to ROM by reload at 18:30:00 UT C T ue Aug 30 2011

System image file is "flash0:c2900-universalk9-mz.SPA.151-3.T 1.bin"

Last reload type: Normal Reload

Last reload reason: Reload Command

Cisco CI SCO2921/K9 (revision 1.0) with 999392K/49152K bytes of memory.

Processor board ID FT X1448AH5X

3 Giga bit Ethernet interfaces

2 Channelized E1/PRI ports

2 Channelized (E1 or T1)/PRI ports

DRAM configuration is 64 bits wide with parity enabled.

255K bytes of non-volatile configuration memory.

4099032K bytes of AT A System CompactFlash 0 (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device# PID SN

-------------------------------------------------

*0 CISCO2921/K9 FT X1448AH5X

T echnology Package License Information for Module:'c2900'

----------------------------------------------------------------

T echnology T echnology-package T echnology-package

Current T ype Next reboot

----------------------------------------------------------------- ipbase ipbasek9 Permanent ipbasek9 security None None None uc uck9 Permanent uck9 data None None None

Configuration register is 0x2102

MSFT -GW2#show run

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 134 of 147

Application Note

Building configuration...

Current configuration : 8733 bytes

! Last configuration change at 20:55:39 UT C Thu Sep 1 2011

! version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service sequence-numbers

! hostname MSFT -GW2

! boot -start-marker boot system flash0:c2900-universalk9-mz.SPA.151-3.T 1.bin boot -end-marker

! card type e1 0 0

! card type command needed for slot/vwic-slot 1/1 logging buffered 999999 enable secret 5 $1$400b$0Kzn2HUoop0OL64b91spK. enable password cisco

! no aaa new-model network-clock-participate slot 1 network-clock-participate wic 0

! no ipv6 cef ip source-route ip cef

! ip dhcp pool 3

dns-server 172.20.2.181

default-router 172.20.8.1

lease 2

! no ip domain lookup multilink bundle-name authenticated

! isdn switch-type primary-4ess

! crypto pki token default removal timeout 0

! crypto pki trustpoint TP -self-signed-3443052460

enrollment selfsigned

subject-name cn=IOS- Self- Signe d-Certificate-3443052460

revocation-check none

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 135 of 147

Application Note

! crypto pki certificate chain TP -self-signed-3443052460

certificate self-signed 01

3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 04050030

31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274

69666963 6174652D 33343433 30353234 3630301E 170D313 1 30383330 31383332

32345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649

4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 34343330

35323436 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281

8100B84F A83B31D6 4CCB9507 199B0675 21042C87 3AC072A1 A9B87146 B33A81B9

71449C3A 8640E523 F2E51F5C 53DA8844 25CD60F4 173A27B2 9FE5D4D0 FC6B2086

CB52FBE7 5B75DBBA 6B0A522C 3FD88D1A 5ABE950D A0E334B8 5DC5C7E4 874CD72B

51A60F19 F935309C DE7146C1 F5EAAFC2 A0B0DC7D 7FF195DD 6105967F 8EB1ABE8

79510203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603

551D2304 18301680 14519620 E52CD148 41A6D69B 8EFEEA88 00ED3CA7 E7301D06

03551D0E 04160414 519620E5 2CD14841 A6D69B8E FEEA8800 ED3CA7E7 300D0609

2A864886 F70D0101 04050003 81810076 D12A4112 963CACAA 59657B51 EA051F2F

4555E416 2FDF32DF 98D031A0 17C88DBB 8ADBD8D9 0770062B 2295D315 7E38C18F

B4C0CCF6 2555CA47 20D09D2B CED701F9 445AD9B3 322783C8 736F1CEE F2AC2F59

823B4C75 5985F137 2A1B77AB 8B6007CE 4FC2C29C 228A3BB2 F0B841B8 5CFA5201

EAEDB235 E35340FD B79542E7 8D754F

Quit

voice -card 0

dspfarm

dsp se rvices dspfarm

! voice service pots

map q850-cause 47 release-source all tone 1

supplementary-service qsig call-forwar d

supplementary-service qsig m wi release-call

fax rate disable

! voice service voip

ip address trusted list

ipv4 172.20.8.38

ipv4 172.20.8.30

ipv4 172.20.8.59

ipv4 172.20.8.85

ipv4 172.20.8.98

ip address trusted call-block cause dest -unroutable

sip

! voice class h323 2

h225 timeout connect 60

h225 timeout call-proceeding 5

h225 timeout ntf 5000

h225 display-ie ccm-compatible

call start fast

call preserve limit -media-detection

h245 caps suppress nte

Enabling DSP sharing and DSp farm services

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 136 of 147

Application Note

telephony-service ccm-compatible icense udi pid CI SCO2921/K9 sn FT X1448AH5X hw-module pvdm 0/0

! redundancy controller E1 0/0/0

shutdown

! controller E1 0/0/1

! interface Giga bitEthernet0/0

description $ET H-LAN$$ET H-SW-LAUNCH$$INT F-INFO-GE 0/0$

bandwidth 1000000

ip address 172.20.8.58 255.255.255.0

duplex auto

speed auto

! interface Giga bitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

! interface Giga bitEthernet0/2

no ip address

shutdown

duplex auto

speed auto

! ip default -gateway 172.20.8.1 ip forward-protocol nd

! ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout -policy idle 60 life 86400 requests 10000

! ip route 0.0.0.0 255.255.255.0 172.20.8.1 ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/0 ip route 172.20.8.1 255.255.255.255 GigabitEthernet0/0

! access-list 23 permit 10.10.10.0 0.0.0.7

! control-plane

! ccm-manager fallback-mgcp ccm-manager mgcp

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 137 of 147

Application Note

no ccm-manager fax protocol cisco ccm-manager music-on-hold

! mgcp mgcp call-agent 172.20.8.38 2427 service-type mgcp version 0.1 mgcp rtp unreachable timeout 1000 action notify mgcp modem passthrough voip mode nse mgcp package-capability rtp-package mgcp package-capability sst -package mgcp package-capability pre-package no mgcp package-capability res-package no mgcp timer receive-rtcp mgcp sdp simple mgcp fax t38 inhibit

! mgcp profile default

sccp local GigabitEthe rnet0/0 sccp ccm 172.20.8.42 identifie r 11 ve rsion 7.0

13 sccp ccm 172.20.8.41 identifie r 1 priority 1 ve rsion 7.0

14 sccp

! sccp ccm group 11

associate ccm 11 priority 1

associate profile 11 registe r CO NF-VGW 3

! sccp ccm group 1

associate ccm 1 priority 1

associate profile 1 re giste r XCO DE-SJC

associate profile 2 re giste r IOS -MTP-SJC

associate profile 3 re giste r IOS -MTP-SJ-G711

associ ate profile 7 re giste r G729-Soft

! dspfarm profile 1 transcode

code c g729r8

code c g711ulaw

code c g711alaw

maximum sessions 6

associate application SCC P

! dspfarm profile 4 transcode

description CME XCODER

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

maximum sessions 2

associate application SCCP

shutdown

For resources registering to the CUCM

For resources registering to the SME

Transcoder resources

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 138 of 147

Application Note

! dspfarm profile 11 confe rence

code c g711ulaw

code c g711alaw

code c g729ar8

code c g729abr8

code c g729r8

code c g729br8

code c g722-64

maximum confe rence -participants 16

maximum sessions 1

associate application SCC P

! dspfarm profile 2 mtp

code c g711ulaw

maximum sessions software 200

associate application SCC P

dspfarm profile 3 mtp

description SJC G711 MT P

codec g711ulaw

maximum sessions software 200

shutdown

! dspfarm profile 7 mtp

codec g711ulaw

maximum sessions software 10

associate application SCCP

! dspfarm profile 8 mtp

codec g711ulaw

shutdown

! dial-peer voice 778 voip

mailbox-selection orig-called-num

session protocol sipv2

! gatekeeper

shutdown

! telephony-service

srst mode auto-provision none

srst ephone description SRST ..Welcome.. : May 19 2011 19:02:06

srst dn line-mode octo

max-ephones 20

max-dn 20 no-reg both

ip source-address 172.20.8.58 port 2000

Conference bridge

Software MTP

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 139 of 147

max-conferences 8 gain -6

transfer-system full-consult

! ephone-dn-template 1

call-waiting ring

caller-id block

huntstop channel 2

! ephone-template 1

max-calls-per-button 2

speed-dial 1 2003 label "SIP -CME-2003"

speed-dial 2 2004 label "SIP -CME-2004"

! line con 0

password cisco

Application Note

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 140 of 147

Application Note

Fax Gatew ay Configuration show ver

Cisco IO S Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 15.0(1)M4, RELEASE SO FT WARE (fc1)

T echnical Support: http://www.cisco.com/techsupport

Compiled T hu 28-Oct-10 17:09 by prod_rel_team

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SO FT WARE (fc1)

Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.

Processor board ID FT X1040A1LY

2 FastEthernet interfaces

2 Voice FX S interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

125440K bytes of AT A CompactFlash (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device# PID SN

-------------------------------------------------

*0 CISCO2811 FT X1040A1LY

Configuration register is 0x2102

IOSGW#show run

Building configuration...

Current configuration : 5053 bytes

! Last configuration change at 00:50:39 UT C Thu Sep 8 2011

! version 15.0 service timestamps debug uptime service timestamps log datetime msec no service password-encryption service linenumber

! hostname IOSGW

! boot -start-marker boot -end-marker

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 141 of 147

Application Note

! logging buffered 900000 enable password cisco

! no aaa new-model

! dot11 syslog ip source-route

! ip cef

! no ip domain lookup

! no ipv6 cef multilink bundle-name authenticated voice service voip

h323

sip

! voice class codec 1

codec preference 1 g729r8

codec preference 2 g711ulaw

! voice translation-rule 1

rule 1 /^9/ /8/

! voice translation-rule 2

rule 2 /^.*$....$/ /732216\1/

! voice translation-profile NPA

translate calling 2

! voice-card 0

dspfarm

dsp services dspfarm

! license udi pid CI SCO2811 sn FT X1040A1LY archive

log config

hidekeys username cisco privilege 15 secret 5 $1$1IWY$fwla1ooHsE/ORF20GsQFz.

! interface FastEthernet0/0

ip address 172.20.109.201 255.255.255.0

duplex auto

speed auto

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 142 of 147

Application Note

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

! ip forward-protocol nd

! no ip http server no ip http secure-server

! ip route 0.0.0.0 0.0.0.0 172.16.100.1 ip route 0.0.0.0 0.0.0.0 172.20.109.1

! control-plane

! voice -port 0/0/0

time outs ringing infinity

station-id name FAX-GW1

station-id numbe r 4089333473

! voice -port 0/0/1

time outs ringing infinity

station-id name 4089336163

station-id numbe r 4089333474

no mgcp package-capability res-package no mgcp package-capability fxr-package no mgcp timer receive-rtcp

! dial-pee r voice 2715 pots

destination-patte rn 4089336164

port 0/0/0

forward-digits 0

! dial-pee r voice 2717 pots

destination-patte rn 4089336163

port 0/0/1

forward-digits 0

! dial-pee r voice 711 voip

description outgoing call to Inte rnational

destination-patte rn 7011T

translate -outgoing calling 2

se ssion protocol sipv2

se ssion target ipv4:172.20.8.42

incoming calle d-numbe r 27..

International fax calling

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 143 of 147

dtmf-relay rtp-nte

playout-delay nominal 80

playout-delay mode fixe d

code c g711ulaw

no vad

! dial-pee r voice 7 voip

destination-patte rn 71….......

se ssion protocol sipv2

se ssion target ipv4:172.20.8.42

incoming calle d-numbe r 347.

dtmf-relay rtp-nte

fax-relay sg3-to-g3

fax rate 14400

fax protocol t38 ls-re dundancy 0 hs-re dundancy 0 fallback none

no vad

! dial-pee r voice 3473 pots

destination-patte rn 3473

port 0/0/0

! dial-pee r voice 3474 pots

destination-patte rn 3474

port 0/0/1

sip-ua

protocol mode ipv4

! line con 0

exec-timeout 610 0

password cisco

exec-timeout 0 0

password cisco

! scheduler allocate 20000 1000 end

IOSGW#

Application Note

Longdistance and local fax calling

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 144 of 147

Acronyms

Acronym

Lync

DT MF

SIP

SDP

B2BUA

OITT

UC-OIP

LyncIT

T CP

T LS

S/W

Application Note

Definition

Lync 2010 Server

Dual T one Multi Frequency

Se ssion Initiation Protocol

Se ssion Description Protocol

Business to business User Agent

Open Interoperability T est T ool

Microsoft Unified Communications Open Interoperability Program

Unified Communications; also referenced in this document as to a user who is enabled for voice on Lync Server 2010 (i.e. “UC enabled”)

Lync server 2010 Interoperability T est Tool

T ransmission Control Prot ocol

T ransport Layer Security

Gateway

Software

Database

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 145 of 147

Application Note

Important Information

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THI S MANUAL ARE SUBJECT

TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS

MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APP LICATION OF ANY

PRODUCTS.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL,

CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR

LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE T HIS MANUAL, EVEN IF

CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 146 of 147

Application Note

Corporate

Headquarters

European

Headquarters

Americas

Headquarters

Asia Pacific

Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

Cisco Systems International

HArlerbergpark

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

Cisco Systems, Inc.

Capital T ower

168 Robinson Road

USA www.cisco.com

T el: 408 526-4000

800 553-NET S

(6387)

Fax:

HArlerbergwe g 13-19

1101 CH Amsterdam

The Netherlands

USA www.cisco.com

T el:

Fax:

408 526-7660

408 527-0883

#22-01 to #29-01

Sin gapore 068912 www.cisco.com www-e urope.cisco.com

T el: 31 0 20 357 1000

T el: +65 317 7777

Fax: +65 317 7799

408 526-4100 Fax: 31 0 20 357 1100

Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at www.cisco.com/go/offices .

Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Czech

Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland •

Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • T he Netherlands • New Zealand • Norway • Peru • Philippines •

Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain •

Swe den • Switzerland • T aiwan • Thailand • T urkey Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe

CCENT, Cisco Lumin, Cisco Nexus, Cisco TelePresence, the Cisco logo and the Cisco Square Bridge logo are trademarks o f Cisco Systems, Inc.; Ciso

Store and Changing the Way We Work, Live, Play, and Learn are servi ce marks o f Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst,

CCDA, CCDP, CCVP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Intern etwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,

Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive,

HomeLink, Internet Quotient, IOS, iPhone, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace,

MeetingPlace Chime Sound, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The

Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their resp ective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0705R)

P rinted in the USA

Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com

Page 147 of 147

Key features

Ability to connect to Microsoft Lync 2010 Server
Provides centralized dialplan and PSTN access
Ability to aggregate PBX trunks
Interoperability across different protocols
Load balancing of inbound and outbound calls
Support for basic calls, conferencing, call transfer, call forward, hold/resume, DTMF inter-working, and voicemail
Support for G729 codec
Support for Cisco UBE/SP
Support for simulated service provider
Support for Media Bypass

Frequently asked questions

Cisco Unified Communications Manager Session Manager Edition provides a centralized platform for managing dial plans, PSTN access, and interoperability between different protocols. It also enables load balancing of inbound and outbound calls.

Key features include centralized dialplan and PSTN access, trunk aggregation, interoperability across protocols, load balancing, and support for basic calls, conferencing, call transfer, call forward, hold/resume, DTMF inter-working, and voicemail.

Cisco Unified Communications Manager Session Manager Edition can be used to connect to Microsoft Lync 2010 Server via Direct SIP using Microsoft Mediation Server. This enables voice calls and supplementary services to be established between endpoints controlled by both systems.

Microsoft Lync 2010 using SIP via Cisco Unified Communications

Manager- Session Manager Edition 8.5 to Cisco Unified

Communications Manager 8.5 and Cisco Unified Border Element

(Enterprise Edition) 1.4 on ASR to Service Provider

IMPORTANT:

PTR Records added for the Lync server and Active Directory.

Stop-CsWindowsService -Graceful rtcmedsrv

Get-CsTrunkConfiguration

Set-CsTrunkConfiguration

Get-CsMediaConfiguration

Set-CsMediaConfiguration

PS C:\Users\administrator.OCS2010> Get-CsTrunkConfiguration

Identity : Global

OutboundTranslationRulesList : {}

SipResponseCodeTranslationRulesList : {}

Description :

ConcentratedTopology : True

EnableBypass : False

EnableMobileTrunkSupport : False

EnableReferSupport : True

EnableSessionTimer : False

EnableSignalBoost : False

MaxEarlyDialogs : 20

RemovePlusFromUri : False

RTCPActiveCalls : True

RTCPCallsOnHold : True

SRTPMode : Required

EnablePIDFLOSupport : False

PS C:\Users\administrator.OCS2010> Get-CsMediaConfiguration

Identity : Global

EnableQoS : False

EncryptionLevel : RequireEncryption

EnableSiren : False

MaxVideoRateAllowed : VGA600K

Identity : Site:lab

EnableQoS : False

EncryptionLevel : RequireEncryption

EnableSiren : False

MaxVideoRateAllowed : VGA600K

set-csclientpolicy -EnableClientMusicOnHold $TRUE

SIP Trunk Configuration for the Fax Gateway

Outbound dialpeer towards service provider

Outbound dialpeer towards SME. CUBE sends all the 10 digits to SME for centralized dialplan

resolution

Outbound dialpeer towards fax machine gateway behind the SME (refer topology diagram for details)

Dialpeer for 7 digit dialing towards the SP

Dialpeer for Fax calls using G.711u - SP facing

Incoming dialpeer SME facing

Incoming dialpeer SP facing

International dialing dialpeer towards the SP

Incoming dialpeer for international calls from the SME

Toll free dialing dialpeer

Incoming fax dialpeer SME facing

Enabling DSP sharing and DSp farm services

For resources registering to the CUCM

For resources registering to the SME

Transcoder resources

Conference bridge

Software MTP

International fax calling

Longdistance and local fax calling

Acronym

Definition

What is the purpose of Cisco Unified Communications Manager Session Manager Edition?

What are the key features of Cisco Unified Communications Manager Session Manager Edition?

How does Cisco Unified Communications Manager Session Manager Edition work with Microsoft Lync 2010 Server?

Related

Cisco 7960, 7962 User Guide: AI Chat & PDF Access

Cisco Unified Communication Application Note | AI Chat

Cisco ASR1004, 7970, 7975 + AI Chat & PDF Download

Cisco: Connecting to Bell Canada SIP with AI Chat & PDF

Cisco IPX 2400, Voice Gateway: AI Chat & PDF Access

Cisco Unified IP Phone Manual: AI Chat & PDF Access

Cisco UC500, 2800, 2900: AI Chat & PDF Access

Cisco Unified Phones: AI Chat & PDF Download

Mitel 3300 ICP 7.1, CUCM 7.0 App Note | AI Chat & PDF

Alcatel 4400 PBX Application Note | AI Chat & PDF

Cisco UC, Express, Jabber, DX App Note | AI Chat & PDF

Cisco Voice Gateway Manual: AI Chat & PDF Access