Digital Studio Processing SDT9000, SDT7000, SDT5000, SDT5200 Audio & home theatre Installation and Technical Manual

Installation
and
Technical
Copyright © 1998 Digital Studio Processing PTY Limited, 2/7-29 Bridge Road Stanmore, NSW 2048 AUSTRALIA. All Rights
Reserved.
Installation and Technical 2.2 Manual - Part No.: DOC-TEC-015 Rev 2–08/98
This manual, as well as the software described in it, is furnished under 1icense and may only be used or copied in accordance
with the terms of such license. The information in this manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by Digital Studio Processing. Digital Studio Processing assumes no
responsibility or liability for any errors or inaccuracies that may appear in this book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Digital Studio
Processing.
DIGITAL STUDIO PROCESSING PTY LIMITED ("DSP") MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD-PARTY WITH RESPECT TO THE DOCUMENTATION, SOFTWARE, AND HARDWARE. IN NO EVENT
WILL DSP OR ITS SUPPLIERS BE LIABLE FOR ANY COSTS OF PROCUREMENT OF SUBSTITUTE PRODUCTS OR SERVICES, LOST
PROFITS, LOSS OF INFORMATION OR DATA, OR ANY OTHER SPECIAL, INDIRECT, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES ARISING IN ANY WAY OUT OF THE SALE OF, OR INABILITY TO USE ANY DSP PRODUCT OR SERVICE, EVEN IF
DSP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL DSP’S LIABILITY EXCEED THE
ACTUAL MONEY PAID FOR THE PRODUCTS AT ISSUE. Because some jurisdictions do not allow the limitation of implied
warrantees or liability for incidental, consequential, special, or indirect damages, the above limitation may not always apply.
The dSP logo, dSP, AudiOS, SPEED, TEAM, TEAM Audio, TEAM Video are trademarks of Digital Studio Processing Pty Limited.
Postation is a registered trademark of Digital Studio Processing Pty Limited.
All other brand or product names are trademarks or registered trademarks of their respective owners.
Written and designed at Digital Studio Processing
How to reach Customer Support
Phone:
Fax:
E-mail:
WWW:
61 2 9557 2292
61 2 9519 8094
[email protected]
www.dsppl.com.au
!
"#$
% & '
#%&( ')
#*!+%&, '!%%%* '.
#*!/%* '.
& & '
01 '
2 '3
45060%7'60%760%7) 8
%$" 8
9!:
'
2; '
& & < )
#=/ ; 9!:
; 3
;
3
4> +47?-. )8
0
7" )8
= )'
4<=% )
%
)
%
%$# )
%
=$ ))
450 & )01 )%$" ).
2
).
2 )
& 0
/0@ 0
7" %
A5%B 9!:
0 & 01 %$ &2 87A'B
87AB
2 1&&' 1&& 2 $*$'/ $*$3/' 2;=$*$'/
2;=$*$3/' 2=$*$'/ #*$'/ #*$3/'
872 9!:
4> '882:
4> '82: =$ #*$'/-
#*$./)
#*$))/-8A:
B #*$-'/-A:
B C=$*$'/ C=$*$3/' C=$*$'/-A:
B 1&&) 2&' & 2 #2 @
<7$ 2*$'/ #2 #*$'/<3/' )
)
)
)
)
)
)
)3
)3
-8
-8
-'
-'
-
-
-)
-)
---.
-
-
-
-
-
-
-3
-3
-3
-3
-3
.8
.8
.'
.'
.
.
.)
.)
.....
.
.
.
#*$'/- .
* =$*$ .
@
* 8
&<&>
*$ '
7& '
&5*$<=$*$ '
! "#
&&*
& = .
=+70) .
450/&*
=22' %71888
0)&*
3
& 3
= 3
0=2 3
7$ '
$% #
&<0=# 2=$* .
=$$* &<=:
=$* 450@7=# 2=$* 3
&<=:
=$* 8
!
! &
&*" 450*" )
0)*" 2&'*" .
7*" $'() *
*'() *
*
) *
D
"&*"#$
:!9E&B
"
D*
:!$
##!AB""
#
DE
>)
#"E$:!">">#(
4
&D
)+'33AB
$
##!
/3.A!*B
E
7E-A'338B
E7
$D
?&/)-8/!*
$E"?*
4-E-8/'3.
4
E
%).8/AB
$*
#
)*D
"#D!# "
#$
#
>
*>A!*!
+
#!''8*
:BE:$
"
$*'88>$*:E5#
*:>F$GE%
A$
"
#B$*;
E$6"/!G#
"/ #6"6!*#"F$!:$
>"6>
!
$#A:#
#BE
="
#)6$>$
"
*"$6*!
$::#*:"6*""
*#E
"$
""
"
#E
%:$
>6
6!*!>
*6
>*
"''8E
%*$"6
$*$E1!6C57!*$
A>
&,#
#&/&B>
>::>(
&'
#14
&
&
#H
&)
&
#/
D
"&*"#$
:!9E&B
%A!#B"*"
$
:!!*6$
*"!""#$
:>*"
#*
$E=#!6>$:
4
:>$
""$
6""6*$):"
>
!E@>D6:
""D"#>$
6
&$**E7/-*:#$
6"-"*$
$*$A"/: "&>"#$
"B6#>$
:">(
#$
4H
"-*$ #$
4/
#$
=%H
"-$*$ #$
=%/
H
/
=$H
=$/
!G"D$
$
!G"$
$
D
):>
$
"6>
):**E="8:
$
"
#$
A#"'/:*$
6"':$
-G
"B6>$
"#$*!*:6*
!G#E%
":$
>!*#"F$!E
#*$% H
#*$% /
#=$*$% H
#=$*$% /
H
2$*;
#" "
#$
*$
2$*;
#" "
#$
$*$
!G"D
/
=$H
!G"
D
=$/
%"
$
:!*6"6
""
:# $*;
6>#"
#*$$*$
**
->"6.>!>
*:E%#7/-
*:E%":$
>!*#"F$!
-/:*E%
::D$#*"$
E
D
"87,1$
:!B
%
$
>) 6
$87&6>87,#
!*E%">#I
J#(
%:$
C:$
""
%:$
%:$
%
:.>!:>.E%#7-
*6
$*;
6"E
""878)$E
! " #
607*
D:!
+E
D*
!$E:"
#
#$*#"$
#6
*#!$!
D$*#$*#:
$#"
* >
#>;*"*D#
D
DIJ>*"
*
"
$#"
* >
#E#*D
"*$*>
>
E2*"!60!6%
"">
$A
K$>
6
#$
"+:D""BE"
>
"
D$
6D
$$E%:D$"
>
#$
A>$**!"+##$I* J
I*JBE=$$
"#"*"$
6:"#>""
D"$
A#!
$*
>*:"
BE
:D6>
#$**
D>":$>!
$
*
"$
#
DE$6
#!
D
$
$
: #
DE
D$
:"*
*
() @G6--E' @G6- @G63 @G6L
D$
#*:K
K
K
$
$**"
KE;**"H/
.EE
%&:
$&,K"
**;!E
;*:>E
&1/-
0
!$E0
&
$
>
:!$I@$!J
$>$&1&:$
#!$>
"@$
!$E
&*"#$
:!9E&E
D$K$>*
&&6:$#!
E
1M##:!
%&M * +#D
E
2M
M!"*$!"+!*"
$
$
D
&
450@7E
&M#
#&
450M450
450@7M450
A@#7$B
#
%
&&
450@7$!$/'!*
6$**#G"131E%:$
A
;BD>
D$
"
E
%
*&:$&&
6450@7!
D:
*N
*E
D$
DA% * B
*;#
D$7!6>*: $*$
&!E
:$
D6#$
"!
*!E%/'"$):#6*:#6@6$*%&,
:
A!
;!B!A>%&: $*$
$*!#'B
@441%&,%&(
=
>
#%&,&G"!
DE"A"
>$#
$$#
%&"&B
!
D*
#"
$
*:A!B
D!$$""
D!#*!#$:"
D
!E#>:
*!
"6
I*J!
:6$#I$
J
>:%&E%$!$!
D
F$6*!$
:$
&
!:"
#%&,E
%D"
D
DE2
D>D:*"
D
ADD"%&D
D"B
#"K$**6
$
DE)"K$**A)*B>::
6A
:*!!;*B6I8JI'JIJ#A#I8JI'JIJBE%
#K$*6
"
:86
:'
:*D!E
$##
:!I:J6:!$:E@6#I8J'6#I8J
I'J)
#IJI'I
IJF$DE:"
K$**#D#E
47
7
8
'
'
8
8
'
8
'
8
'
'
8
)
8
8
'
-
'
8
'
.
8
'
'
'
'
'
*%&#
"#:$A!B
$
$
$E
"$!
$:#
*#"
K$*
D6*:>
"D"$
"#
DE :#
D!$
&
*D"E
%> $$"$
%&6D!"$: $E"6*>""$"$
:
%&>
$:":**E2$!$**
&,'-:A*
$):!"$$BE%F$D):!A':!:B"
"**%&E"!$#!--E' @G*#"F$!
':
*6--6'88':**
E'$"$
#
>$*!(
'8-:!*2:!A#:!B6F$D.E'2:!"'$"$
--E' @G*
':**E
@$#:D"$6">#**;#*!D$:
D
"
'/:*"--E' @G(
1%&ME.$
-1%&M')$
31%&M3E-$
$
**>$
#"*A #
$B
$
: $>$#!
*"
K:E
$
: $*
D6
&&$=4%%*
DE<)*$
*
#%
E$**
*#826382
'82
'.2A%3888
!BE$&
**#>%888,6>&**#>%3888,E
&
#*$
:$
%$> 6*":!2
!
#A
$> D!
$B6D!-$"
$*$"$
$E=#*$
>D!&E6"I%%J#"#
$$!6$
E%K$*#"%$&>
"#$D"A$
#K$*BE
&
/*
$#=45
K$*#$
:#
A"%$"*6K$*
#
"">:>>$$
6* K$*#"
!$$D"*BE6%.88
$***!
"6D$#*K$**E
4=%#K$*#%
DE
%%888$**<*">%3888
$**6<)*"E)**
>$#*E
!$$*)*:*
D
A%3888B>D!#*
D
A%888B*
#*:"#E
)*
)"A%3888B44=%
44=%:
:!
44=%
DA%888BE"*:!E
%">#/*
A
&%7=415
%7=415
/*
$#B
!
%7=415
6<)*AD$**;!B(
!"##$%& '
(
%)$
)*
+
%$,
#$-
.*
+
-$*
)$/
%-*
+-
#$*
%,
%-/
+,
%-$*
,.
SDT9000 Jumper Settings for DEP Use
ID #1
Compression
Disabled
SDT7000 Jumper Settings for DEP Use
ID #1
Compression
Disabled
SDT5000 & SDT5200 Jumper Settings for DEP Use
ID #1
Compression
Disabled
##
'.#
!> >"&E%*01
*:
01!:$
E%$"
*
!"
*!"E
6&01
**88;88'E
!
&01
*
&E
2
D"
&0$$"A0B"*E"$
"062
*:
>#$#E
!
=22
A=BE
!
!
!
!
!
!
!
!
"
#
"
#
$"
#
"
#
"
#
"
#
"
#
"
#
"
#
%&%
! " #
"*6
&450450*&E%
6/
3*
7-EE:$
-0%7E
0%7'6<)
3*7-0%7,
%,E*
D:
E%D
D
$#$&D&
IJE
!
=22
A=BE
'
'
'
( ( (
'
(
(
(
(
'
'
'
)))
'
(
(
'
"#
*+,-
.
$%
7)A3B""$"&E%$/:D
$
$:*$##
A>D*OBE
%$
&7"*##!E
!=2:
E
&'(
%*!> !:
$#0450
:!
!:
:$E
3:>>
% !:
"!$E :#"!$>#
:F$">#>:""
EE
#
>:D
E
/!
/
!/
/123*45&-4%6
0
0!
'
0!(
0!
(
0!'
0!
'
0!
(
0!'
0!(
%715
)
7-A3B">=7$E$$) $
87&>D
87
*E
!
=
E
%*/$
$:D:
&7D.&: *E7D-: *
;*#A2C42C=%BE%4=
""
:>7D-
7D.: *6$
#E
.***$
*$ E$!$**!'*>
#*N*:*E
!
5&%':
E
"#
"#
"#
"#
8
8/
9
8
8
8
8
5%6:15
**
+,-
&&+.E
%:
7) !:
E
% "&&A*
>6
:$
:$BE
A%*:B !:
*$##
&!
> !:
&E
!
=2'
!:
*:
E
!
!
!
"#$"%&
-./0
.*D
#
#$
=ABE""A!B"E%!
:"#$
A*+$:
B*
D=E
"$#=7ABA
B6 '/6 3/'6 '/-
./)E
6 <:"#$
*$
A '/<3/'B"$/P6/P**
D6"
*$$*$E
E""
6!"$"$
D
* E '/-6 ./6 3/'6 ')/'6 '/86 '/-E
%!
$**) "E""$
!6>D6:
: *"*$*"F$
E%- **$**!-
!6$"E""*E
4(E""
'*D
###
*
D#"$
6"#6
* !E%*$
=7
=)##"
*D
#" !
##D
#:!
D#>
*:* !E@!"$:F$
") "$
$#
*"E$#E""E
"-"=F$
A-
>&B6
=A/B:"#$
"=E6#D!
"""$
E"6
!$
:$
&E
%
&> 66<E="#$*:
A>***
>
">B6">D:
E;*
*:*$
" <<6*:D=
<
<6>#<E!"#$
A'6-) B6
&!$
:$""E
!
=:
E
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
(
'
(
'
?/(
?/'
?/(
?/'
*661,:*5@"
6*:>:46&45&#
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
(
'
(
'
?/(
?/'
?/(
?/'
*661,:*5@"
6*:>:46&45&#
%;%:4<
"54,=>9#
*661,:*5@"
6*:>:46&45&#
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
*661,:*5@"
6*:>:46&45&#
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
*661,:*5@"
6*:>:46&45&#
(
'
(
'
?/(
?/'
?/(
?/'
%;%:4<
"54,=>9#
%;%:4<
":54,=>
#
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
(
'
%;%:4<
"54,=>9#
(
'
(
'
?/(
?/'
?/(
?/'
*661,:*5 @"
6*:>:46&45&#
%;%:4<
":54,=>
#
(
'
(
'
?/(
?/'
?/(
?/'
*)4E
&'(
*> !:
6
%*: !:
*E"
!:
*
$"$!6 !:
:
E4=%
::$
$$!
>AB
!> O
!
!:
":
E
/9
/!/
/!
/!
/!
/123*45&
*)-
&;#
D$7!6;
;*: $*$E
$
!:
>$E$**
>&"
*$*E
%
&> * *
DE "
""
D"E
!
&AB:
E
16:5*6%,>
7:
16:5*6%,>
7:
16:5*6%,>
7:1564<
7:
16:5*6%,>
7:
8
98
/8
8
8
8
8
A8
8
*)
12(-+-
"&*;>
> > "
D
#=*$#A.BE%;
>
>".*>
"A$#BE
$
D
**
$#$:>
E%>
"
*"
=:
E
3+1 456
&&,> E
"$#4/;A'8:B> 6$:#:!
'8:*#!E
!
$ :6:6
:
>.8E
%;$
"$#> '82:E
"$#7?-.>
*A'88:%B> 6$:#:!
'88:%*#!
#!.:#$
E$>4=%D;$$#*$$#:#
*
D,E
"#!>&,6#6>
6:!:$
!:>> *
: "&,E
"#>&,6$:$:
&,>
$:6*":!
$##:#E$:$**#>
:#D;$6 !$
E
%;$
"$#> '882:E
!
&> *E
( %
$: #"
*>:
*
*$DE!#
>
#
!>E
%*
6">$:>
DE!E
!
=22
E
%&1*1.
*./
%*>
#$
:"
!$"&E%>*$
>$*$">:*
&E""
E:>>
$#>; E&E""D7 D
A*&E
"!
""
*
$$
:$BE
%*$$!*D
"#6
>DE
!
=
E
0
0
(
'
(
'
0
0
(
'
(
'
6B+:>46&+:B+:>
2(-+,/7
>
*$
$*$D4E
%!$:">I;E
4J$*$E
6*
#
6"
$$#
=%*E
!
=
A4BE
?/
?/
?*5&<*,=
6$+:
?/
?/
8(
$:
"5%A
BE"0%7':
>"0%7
0%7)$:
E%D*
$!>D
0%7A
BE
0
(
'
%C1,*&1
6*661,:*5>
8($
5%A
B"
0%7"
$$#E
@!6>$
>
450A@7B:$!:$
"
D+*$!
$"$"!
*
>3*
E
!
%C1,*&1-5*+;-
8(/$
&#
"
$$#*EDE!#$:
0
7"6$#>
D:DE!E
!
=
E
0
(
'
%C1,*&1+:
%&'#
'.#
!> "450E%*01
*:
01!:$
E%$"
*
!"
*!"E
645001
**88;88;'$
>N4%
*#!E450@7
6***!%71888%$D
6
>-8;-8$>-:$A$BE
!
&01
*
4506D%71888
E
0"$
"$
1"$
$%
7)A3B""$"450E%$/:D
$E
!=2':
E
"#
*+,-
.
(8
4>$
$*E
!
=2:
"#
*&1C
2
*!
**E
%*$
""!$*E%*$!$"$""$
:$###
$#*#
D*
"
&$!E#!
E
"*6!
*!
*E
%*$#$
&
3#$#&E3*7-"450:$$#&
**!#E$
:
450*&E
!=22
E
'
(
'
(
(
'
(
4
7>
*E$6>*$
>$*$*E
%*"
*D
#E"
.D
E
!
%71888:
E
9
2/4-*$
"
/0@D
#E!
"450@7
E
!
%71888:
E
%>4E4$!$E
( %
4
7"D
"#E
;*
: #E
!
%71888:
E
8(:;
4
450@7,
@!>$
450E
&'(
%*: !:
*E
% !:
:
!:
"!$"&:
> !:
>:
450>>
#
E
4=%(:
D6*$>:$ !:
*/
$*E$&
"
*>
>
450
A#B:"*>#450"E
/9
/!/
/!
/!
/!
/123*45&
'#
'.#
!> >"0E%*01
*:
01!:$
E%$"
*
!"
*!"E
6001
**'8-;8.E
!
&01
*
0E
0"$
"$
1"$
$
7)A3B""$"0E%$/:D
$E
!=2:
E
"#
*+,-
.
**
-
37) "*
0E""*
6*$!
"*
>D!
0E
!
=2':
E
"#
*6>*<1
0(
37-$"
E%"
$D! >>
!$DD
*"$
#E%*!"
$
$*>
D$"0E
!
=22
0E
4&15
<" :!;
37-'87"$EA$*"#87:
BE
!
=22
E
D
'
(
(
'
<" :";
37-87"$"87Q*E
!
=22
E
'
(
(
'
3$>&E%
:!
:
E% >!A%:>::
&0
BE%>#2$"0:!&E
!
=22
A=BE
!
!
!
!
!
!
!
!
"
#
"
#
$"
#
"
#
"
#
"
#
"
#
"
#
"
#
%&%
!
1&$*&3E%*$
7-*$E
!
=22
A=BE
7'
7(
7(
7'
"
1&$*&3E%*$
7-*$E
!
=22
A=BE
7'
7(
7(
7'
+
7-":>*
2
0)+.A
*
2 3BE% "*
2
0)E!
=22
E
7'
7(
7(
7'
1$$!=
"$*$'87E.*D
#
#$
*$
AB"E%'2C:$$E
4=%(%*$A'/<3/'B:"#$
""*$E
4=%
6#D!"""$
A""6!$
:$
&BE@>D6
0)
>*$6$"!"#$
6
&!$
:$""E
!
=:
E
'
%;%:4<
6
"54,=>9#
(
'
(
'
'
6B+:>'
%;%:4<
6
"54,=>9#
(
'
(
'
?/(
?/'
?/(
?/'
1$$>!?
"$*$87E.*D
#
#$
*$
AB"E%2C:$$E
4=%(%*$A'/<3/'B:"#$
""*$E
4=%
6#D!"""$
A""6!$
:$
&BE@>D6
0)
>*$6$"!"#$
6
&!$
:$""E
!
=:
E
'
%;%:4<
6
"54,=>9#
(
'
(
'
'
6B+:>'
%;%:4<
6
"54,=>9#
(
'
(
'
?/(
?/'
?/(
?/'
)/$$!=
"2;E.*D
#
#$
$*$"E%
#$E%*
E
!
=:
E
%7'
%;%:4<+:
"54,=>#
(
'
(
'
(
'
(
'
0+:B+:>'
)/$$>!?
"2;E.*D
#
#$
$*$"E%
#$E%*
E
!
=:
E
%7'
%;%:4<+:
"54,=>#
(
'
(
'
(
'
(
'
0+:B+:>'
/$$!=
$*$"#""
#$E%
:"
A
##DB*D
:!$E.*D
#
#$
$*$
"E%*
E
!
7$:
E
*6%:*5
+:>'
%;%:4<+:
"54,=>#
(
'
(
'
(
'
(
'
*6%:*5+:B+:>'
-$!=
*$"
#E"
#$
"E&
E!
7$:
E
%;%:4<
6'
%;%:4<
6
"54,=>#
(
'
(
'
(
'
(
'
%;%:4<
6B+:>'
-$>!?
*$"
#E"
#$
"E&
E!
7$:
E
%;%:4<
6'
%;%:4<
6
"54,=>#
(
'
(
'
(
'
(
'
%;%:4<
6B+:>'
<" & "*"87:
#*ABE
!
=22
A=BE
1:15>
1:15>
'
(
(
'
'
(
(
'
<<*:-15B%6>*:*661,:1&"#
1:15>
&'(
%*: !:
*E
% !:
!:
"!$"
&:
E" !:
$
!:
>
:
0>>
E
4=%(:
D6*$>:$ !:
*/
$*E$&
"
*>
>
0
A
B
:"*>#0"E
/9
/!/
/!
/!
/!
/123*45&
3+!<<'
4
$
E
3+!<'
4
$
E
2(-+
>
*$D4E
!
=
?/
?/
?*5&<*,=
6
2(-+/$
>
$*$D4E!
=
E
?/
?/
?*5&<*,=+:
-$!@"5
*$"
#E"
#$
"E&
E!
7$:
E
%;%:4<
6
'
%;%:4<
6
"54,=>#
(
'
(
'
(
'
(
'
%;%:4<
6B+:>'
-$"6#"
*$"
#E"
#$
"E&
E!
7$:
E
%;%:4<
6
'
%;%:4<
6
"54,=>#
(
'
(
'
(
'
(
'
%;%:4<
6B+:>'
-$##5<:7'-(;
&*$"
#AR$:
RBE"
#$
&"E
!
7$:
E
%;%:4<
6
'
%;%:4<
6
"54,=>
#
%;%:4<
6B+:>'
-$5!5=:7'-(;
&*$"
#AR$:
RBE"
#$
&"E
!
7$:
E
%;%:4<
6
'
%;%:4<
6
"54,=>
#
%;%:4<
6B+:>'
A/$$!=
;$*$E.*D
# "
#$
$*$"E%*
E
!
7$:
E
0:54+:>
'
%;%:4<+:
"54,=>#
(
'
(
'
(
'
(
'
0:54+:B+:>'
A/$$>!?
;$*$E.*D
# "
#$
$*$"E%*
E
!
7$:
E
0:54+:>
'
%;%:4<+:
"54,=>#
(
'
(
'
(
'
(
'
0:54+:B+:>'
A/$$!@"5:7'-(;
;&$*$AR$:
RBE.*D
# "&"
#
$
$*$E%*
E
!
7$:
E
0:54+:>
'
%;%:4<+:
"54,=>#
0:54+:B+:>'
#
1&$*&.E%*$>
*
>
*E
@>D6"!
"$&&E
!
5&%':
E
"#
"#
"#
"#
8
8/
9
8
8
8
8
5%6:15
(#)#
+.7- "*
2 2&'E
#""
*
2 E
!
2:
D:::E
*6%:*51>=
*6:5*<
'
(
(
0(
0'
1C4<1
*6%:*51>=
*6:5*<
'
(
(
0'
0(
-
4
$
E
=9(, $
%>.!#:
#E*"!
#
"#$$
E%!*!.C57: $:>$
:
!*E
&4=417%=4(
%*$"
$74%
74%"
74%
.#*$6!2*$'/6#*$'/
<#*$3/'E%!D
E
"!$
:
E
%6>*.
6>15:>16&
1>,5%B:%*6
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
4<1
%6>*.
6>15:>1:+56
1>,5%B:%*6
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
1C4<1
$!=
.!#:
##E#
"D#$*$"#F$!
,"
:!0)2=$*$'/E
"!$
:
E
%6>*.64<*;*6%:*5
6B+:>'
1>,5%B:%*6
%6>*.64<*;*6%:*5
6B+:>'
-(
-'
-(
-'
-(
-'
-(
-'
-(
1C4<1
1>,5%B:%*6
-'
-(
-'
-(
-'
-(
-'
-
.!#'8$:
#>14E:
*$"8
#8
#$*$E
"!$
:
E
%6>*.64<*;1:15>
+:
1>,5%B:%*6
%6>*.64<*;1:15>
+:
1>,5%B:%*6
4<1
-$!=,>!?
.!#:
##E%!*!.C57: $:>$
:
!*E#
"###"
$ E
&4=417%=4(
%*$"'#*$74%
74%"
74%
E%!D
E
"!$
:
E
%6>*.64<*;1:+56 1>,5%B:%*6
6B+:>'
1C4<1
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
%6>*.64<*;1:+56
6B+:>'
1>,5%B:%*6
1C4<1
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-(
-'
-$!@"5
"7"$:
##"/*"$
*!66E$:
*$"/'8
#8
:
#$*$E
"!$
27*$:
E
+/$$
2C57D"
:
*>*"*$">!* !E
C57&
#
'
14
@AHB
)
A/B
"!$
2C57:
E
:
SJK D"
:
*>*"*$"D>!
* !E
SJ?
#
%*
@AHB
7#
A/B
D
14
"!$
2? :
E
A"'-JK B
$:
A"7,BD"
*>*""
D* !E
SJ?
#
%*
@AHB
7#
A/B
D
14
"!$
2C57:
<? :
E
A"'-JK B
$:
A"7,BD"
*>*""
"$D* !E
SJ?
#
%*
@AHB
7#
A/B
D
14
"!$
2C57:
<? :
E
9(
!
"#$
"%&%'(#)*&"+%,'+"#%,
-"(',&&,#$
.!/
/
!
"
#
$#
$:
SJK E5D*$")$#
:!;#
E
"!$
2&:
E
%&
'
$:
SJK E#
"
**"E
"!$
2&:
E
,13($
$:
SJK E#
D*"
**"E
"!$
2&:
E
!
"#$"%&%'(#)
*&"+%,'+"#%,-"(',&&,#$
.!/
/
- 8
$:
SJK E%=%&%"
*K *:>*
2 E%$*$
D
"*>
**$
/>!A=""B>#:>E
"!$
2&:
E
0$,/$$
4
$
E
## $
--
%
*!>D"&:!>#
!01
*
!DI"$JE%D
$#!$"*$*
#!*""&E
%#"#"
01
*6>D6
>!
*$#:
"*$*E7D)
AD
*
":
!B6:>>>F$
2%:$
""$E7D-
>$**#$#
:6>D$: *E
&
K01
*E%
$!
:$
#!* #601
*>&:$
E
@
%&:
D$
""D
D:$.8*
"A
#
BE%"*
)** =:
"
DE%$D3*A$
B:
#E
%&$**:'
-:$
A$!':$
$**
:!">BD'
>
' $**
*
$#:
E
/
%=:
D$
)** "&:
D3*A$
B
:
#E*$*:
E
6=:
$**) "' "
>*
$#:
;
*:) "
E
%=
6- "*$>$*DA!
B
- "$*$E
"&>:
#:>
:!>#"
""*
">"E
%=:
"$!">/*#:A15:/*#
B#
"AB" E1!*#
: "-A
*D!BE
%:D/*##
*>#
$!:
:!
&$
*E4=%
4=%#
*>#E
4=%
"!$>$
#""!$!6!$
:$
&E
/1 *#
%=D"$
$
&K$>
&E%
=22':
">=
>
D*
D450
0E
%=
*"(
()#
7-*:*$
$";#=7,6"'6
>")E$!!:
>
!$**
">
#=7E
"' F$
>
0
$*- :
$#=7:!
#
:
=7E
$*$
%>"2$
2*:
D$2'888
#;6
$#**!*6
&0E
%*:">*#
: 7-*"F$
E
7-*:3**"E%>*
6
$*;
: *"&""
3*
D$
0%7,%,E%D*
:!">*
$#
E%*
#
&450$#/
3**E
+,
/0
$$
0120%
$,
+
%
+
%/-$
!"#$
%
&! '''
($%
%&
$
!
!)*
%=
*$"DE!
#E%
*$
$*$$**
E
#
!)*%
%
++&
$
$
,$,
%
+
(&$
#
$+
-#
.
%$&$
$#
$
$%,
&$
+.$
#
,%
%&'*# $
/!
%=22':
*
D0
450
E
%=22'405/D!::
**$
>"$",E"
!7-*$
"3*"450:!&E
4=%4503**/
2%":*$##
450
3**: "&64=%!"0%7*E
%7-*450D"=22'"#$
(
!
"#
#$%&'
****$
>N4%
$*2%:
"#$
=2)E
%:
$*D"*=22':
:!>
*#:,:
>
#:>E%>
=22':"#$
!"$:!">6$#!*"
*F$
$!
:
E
*6!*:"
&*!!#:
!*E
"D#=22':
!*"&6$(
D!*
E
"#$
:
$*E%:
:*#
"
A:!
&B6*#:*>**
$*E
%&
$
%
#
!14
! 3
! '
!'
!'
!)*
)$%
++
%%
.
"<<<(
%%71888:
#D
:
$"$
:!%$DE
D
#G#
*:*D
/0@D
#6:&5
4%
"E
"$"%71N888:
6%71N888$**
450@7E:"$
I%#T2$J
!
D"450@76
"
I% JI%#8882$JE""&"6>:D>
>*/
:N7
E
'+# $
%0&:
#$
=E%$
*
)** =
:
"
DE%$D3*A$
B
:
#E
4=%(%:
4=%
&&&
E
4=%
/
%0=:
#
#"
#$
ED$
)
** "0&:
D3*A$
B:
#
*$
*:
6D
": *
*&:
D:
#E
60=:
$**' "E
"&>:
#:>
:!>#"
""*
">"E
%=:
"$!">/*#:A15:/*#
B#
"AB" E1!*#
: "-A
*D!BE
4=%(%:
4=%
&=
E
4=%
%:D/*##
*>#
$!:
:!
&$
*E4=%
4=%#
*>#E
4=%
"!$>$
#""!$!6!$
:$
&E
/
%0=2:
$
"#"0E$
*"D$"
">#"$(
&
!
%7)*"*"*
E
()#
%>7-*:*$
$";#=7,E;$"
*872;#:
E
$*$
%>"2$
2*:
D$2'888
#;6
$#**!*6
&0E
%*:">*#
: 7-*"F$
E
#
=
7-*:*"$:>*
2
0)E
-
! #
%>
7-*:*$
""$$"$!E
.
$/
($+$+
!14
4
$5 /$
-'
$
+
%
%>/
7-*A
*6/
"F$!B$
D* ""872
#"87E*"87Q6/*
:$:
: *A872BE
!
/
#%!)*
$%
%
/
$
/#
+
8$+
%
$
%$:
#>#"-
#*$)
#$*$E%
*$
$*$: $*">(
*$
=$*$
U$!
$
U$!
&$*
'
!$
"
;:$
'
)
"
#
R$:
R
&
'
R$:
R
&"
#
"#D
2&E
%$*$"#
:"
$*"
A
##$
DB6$*$">"
2&E
#,'- !
%">#*#*")"=*#"&
0E$
$":
$!6*:#$=,"55&,<0,
>:
E@">#
##$
E%=!$!!
C%56:$> D*#>#E
%"*#: E%'=$:6
=*#6
)$"$"=E
4=%
4=%#=#>:>ED!
4=%
*"$#"&
0#:>
:
E
*:"=:
"$D$6>$!$*$E
%$$!$>D
$:
D:"
E
"&0:D#!6#"
*
#06
=#E
((/$
0234565+"152+77777777
+""032++84
"9"0+29"0:5$
;;
;
9:2<%..=
;;
;
%-;*;*
!
""""""
#!$
!
""""""
#!$ !
""""""
";%$##3:,$/$
1;
,3+;
>;"6>"
2;":1?
1/0$$
0234565+"152+77777777
152+"80++84
"9"0+29"0:5$
%&!!'
()$
%$*+$,
(!)$
!!#+
(!)$
-"*...+$,
()$
/!#+
(!)$
"....+$,
()$
0#1,!2
(!)$
"3...+$,
()$
*4!#
(55
6"7...+$,
()$
,8.88 ()$
-"*...+$,
()$
*8.881
()$
"....+$,
()$
*8#1
(22
*#1$
(!)$
8#!'
()$
8#9+:#;
(3
8#9#;
(<=
#8!
(8
:%>!8
()$
#.?@6*
(!"<
!9#;
(
,/'(./$
0234565+"152+77777777
45@212"0562+84
"9"0+29"0:5$
!2'
()$
!)$.!
(!)$
*"!2'0
()$
".$#
(*
0# $*
( !)$A
(3.-:06
"A )0
(
!)$<
(<.-:03
"< )0
(
"!)$.!#!
()
"3 )0
(
"6 )0
(
!)$
(37-:07
'!0.%>
()$
"$
(
$< +!!
()$
$08
("
"B
(
"#!$B
(*
!)$*!
()$
!)$"A!
(!)$
" $
(
" $
(
!)$"<!
()$
" $
(
" $
(
*#=5%05E
9 1/
%">#*#*""=*#"450@7E$$
":
$!6*:#$=,"55450@7,>:
E@">#
##$
E%=!$!!
C%56:$> D*#>#E
%"*#: E%'=$:6
=*#6
)$"$"=E
4=%
4=%#=#>:>ED!
4=%
*"$#"450@7#:>:
E
*:"=:
"$D$6>$!$*$E
%$$!$>D
$:
D:"
E
"$:>450@7
&":6
=#E
((/$
0234565+"152+77777777
+""032++84
"9"0+29"0:5$
;;
;
9:2<%..=
;;
;
%-;*;*
!
""""""
#!$
!
""""""
#!$ !
""""""
";%$##3:,$/$
1;
,3+;
>;"6>"
2;":1?
,/'(./$
0234565+"152+77777777
45@212"0562+84
"9"0+29"0:5$
!2'
()$
!)$.!
(!)$
*"!2'0
()$
".$#
(*
0# $*
( !)$A
(3.-:06
"A )0
(A
!)$<
(<.-:03
"< )0
(AA
"!)$.!#!
()
"3 )0
(C
"6 )0
(A<
!)$
(37-:07
'!0.%>
()$
"$
(
$< +!!
(!)$
$08
("
"B
(
"#!$B
(*
!)$*!
(!)$
!)$"A!
(!)$
" $
(
" $
(
!)$"<!
()$
" $
(
" $
(
*#=5%05E
#$ *$
/)*$"#$:6&E
=$*$
/)$*$"#$:6&E
*$
-"DC577
>$*7D
=$*$
-"
DC577
*#F$!
) @GV- @G
&5W4%A64B
!$
6;
66%
60!E
?
4()
2;$('8
#
@Q+*$;
D7F$
@"@#)XD=!
88*
D#&>$*A
D
B
'8Y-808E.W'88Y''808E3
& &>$*
)88
@=$*$7#
-'8%@Y-80W)-'%@Y''80
.
7 W'.;-);-A@;;
B
#
#
%&'$ *$
'*0
'0@
=$*$
'*0
'0@
7"
0!0
&54%A64B
#
@Q+*$;
D7F$
@"@#)XD=!
88*
D#&>$*A
D
B
'8Y-808E.W'88Y''808E3
& &>$*
)88
@=$*$7#
-'8%@Y-80W)-'%@Y''80
.
7 W'.;-);-A@;;
B
#
8 #
'+$ *$
'2C$*$"#$:
-1*$A)<'&B
=$*$
'22C$*$AB
2#=$*$AB
-;$*$A'<&B
#>
-*$;)$*$
>:!*
*#F$!
) @GV- @G
$
6;
6E
?
4()
2;$('8
D#&>$*
'8Y-808E.W'88Y''808E3
& &>$*
)88
@=$*$7#
-'8%@Y-80W)-'%@Y''80
.
7 W'.;-);-A@;;
B
#
#
&>$**!
0#*$
0:380/80
4&>=$*$
-0.*
7 3;-);'3A@;;B
#
'8 #
(#)$ *$
-#*$A':
<$:
B
2*$"0)#>
&>
&*$"@
**
)@
*$*$
=$*$
'8@#2&
$$
* *
C57
$$
* *
?
*
A7B
*
A
? B
;&$*$
=$*$*
.8!*
F$!7*
@G/'.8 @GA$:
)
B
#4
+38
!*
8E88Z8@G/8 @GY'807288[
#>
)*$;$*$
D
$>#
& &>$*
.8
@=$*$7#
.)%@
.
7 @#
'.;-);-A@;;B
#
)8 #
.
$ @
D
D>7
2;$"-)X
DE
& &>$*
.8
@=$*$7#
..3%@
.
7 @#
'.;-);-A@;;B
#A
DB
). #A**;=!B
$!5
#A-
DY388#B
. #A**;=!B
Installation and technical
Internal System Cable
Diagrams
Installation and Technical Manual
A
CB L0102
Primary
IDE
CONTROL
SPEED
DB9
Co m 1
Floppy
Keyboard
(32M Ram)
& ports controller.
with on-board IDE, floppy
CBL0102
CBL0123
CBL0122
CBL0109
IDC26
CBL0124
P1
Floppy Drive
P2 or P3
CBL0182
IDE HDD
CBL0184
T/C VSYNC
IDC10
P3
I/O C Card
VTR / NLV
MIDI
02 R
P6
IDC26
CBL0180
SVGA card
P4
IDC10
Pentium Motherboard
TOUCH
Com2
IDC10
depending on the system.
connected to either P2 or P3
cable (CBL0109) above, needs to be
NOTE: The touch screen interface
require CBL0125.
Rev3 requires CBL0191, all other revisions
depends on the revision of scroller card.
NOTE: The scroller/SVGA cable above
CBL0125
R Card
P5
P1
P97
P68
P67
P24
P26
P90
P72
P3
P2
P91
CBL0181
P6
SVGA
KBD
JP1
CBL0191/
P71
SCROLLE
CBL0178
DIGITAL I/O
DB 3 7
P2
CBL0120
Design:
dSP
Phil Scarratt
Drawn :
1997
Date:
7/11/97
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
CBL0179
CBL0110
SCSI TP
P1
BRIDGE
IDC50
BRIDGE
IDC50
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
J5
P3
PTY LTD
SCSI Tape
Drive
Scale N.T.S
Sheet 1 of 1
CBL-SCH-005-R1
Drawing Number:
Track System
DEP Internal Cable Schematic For 16
Title:
DIGITAL I/O
IDC40
J6
I/O A Card
WCLK
AES/EXT
dSP 6 Card
IDC50
SCSI TP
IDC26
CBL0100
CB L0118
SCSI
CB L0102
Primary
IDE
CONTROL
SPEED
DB9
Co m 1
Floppy
Keyboard
(32M Ram)
& ports controller.
with on-board IDE, floppy
CBL0102
CBL0123
CBL0122
CBL0109
IDC26
CBL0124
P1
Floppy Drive
P2 or P3
CBL0182
IDE HDD
CBL0184
T/C VSYNC
IDC10
P3
I/O C Card
VTR / NLV
MIDI
02 R
P6
IDC26
CBL0180
SVGA card
P4
IDC10
Pentium Motherboard
TOUCH
Com2
IDC10
depending on the system.
connected to either P2 or P3
cable (CBL0109) above, needs to be
NOTE: The touch screen interface
require CBL0125.
Rev3 requires CBL0191, all other revisions
depends on the revision of scroller card.
NOTE: The scroller/SVGA cable above
CBL0125
R Card
P5
P1
P97
P68
P67
P24
P26
P90
P72
P3
P2
P91
CBL0181
P6
SVGA
KBD
JP1
CBL0191/
P71
SCROLLE
CBL0185
DIGITAL I/O
DB 3 7
P2
CBL0120
Design:
dSP
Phil Scarratt
Drawn :
1997
Date:
7/11/97
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
CBL0179
CBL0110
SCSI TP
P1
BRIDGE
DIN96
BRIDGE
DIN96
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
J5
P3
PTY LTD
SCSI Tape
Drive
Scale N.T.S
Sheet 1 of 1
CBL-SCH-001-R5
Drawing Number:
Track System
DEP Internal Cable Schematic For 32
Title:
DIGITAL I/O
IDC64
J6
I/O A Card
WCLK
AES/EXT
dSP 7 Card
IDC50
SCSI TP
IDC26
CBL0100
CB L0193
SCSI
Floppy
Floppy Drive
Primary IDE
IDE HDD
Mous e
Com2
CBL0 0122
(32M Ram)
& ports controller.
with on-board IDE, floppy
Pentium Motherboard
Touch
Com1
CBL00171
P5 or P6
CBL00172
on the system.
connected to either P5 or P6 depending
(CBL00171) above, needs to be
NOTE: The touch screen interface cable
I/O C Card
DEP
P5
IDC10
CBL0 0173
Keyboard
CBL0 0123
CBL00100
P45
P2
P7
P8
P6
P5
P10
SVGA
Vin
Vout
BNC
BNC
BNC
KBD
RCA
Mini
DIN
RCA
BNC
BNC
BNC
SCSI
DBHD26
Design:
DSP
Phil Scarratt
1996
Date:
7/4/98
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
Drawn :
SVGA card
PTY LTD
Sheet 1 of 1
CBL-SCH-004-R3
Drawing Number:
NLVHR Internal Cable Diagram
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
Scale N.T.S
Title:
Targa 2000
DBHD15
IDC50
SCSI TP
Adaptec SCSI Controller
CBL00120
Unless otherwise specified
CBL00174
CBL00170
SCSI TP
Disk
Floppy
IDC34
FDD
Port
Parrallel
LPT 1
IDC40
IDE 1
Control
Speed
WCLK I/O
P1
P7 or P8
P5 or P6
Card
DSP
Bridge
DIN96
DIN96
J5
Bridge
Card
I/O A
Digital I/O
IDC60
J6
P2
Digital I/O
DB 3 7
the system.
to either P8 or P7 depending on
to the left, needs to be connected
NOTE: The Speed Control cable
depending on the system.
connected to either P5 or P6
cable above, needs to be
NOTE: The touch screen interface
IDC26
Co m 1
IDE HDD
Controller)
Touch
Co m 2
(onboard IDE/Port
Motherboard
Keyboard
card
SVGA
P33
P32
P34
P31
P20
P15
P2
P14
P10
P8
P5
P46
SVGA
P7
P6
P29
P48
P30
World Clock
Out
World Clock
In
P35
Pin18
Pin26
Pin24
Pin25
KBD
P5
IDC20
P4
IDC40
P3
Digital I/O
Digital I/O
Design:
DSP
Peter Firley
Drawn :
1998
Date:
7/8/98
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
PTY LTD
Sheet 1 of 1
CBL-SCH-007-R1
Drawing Number:
VCS3 Internal Cable Diagram
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
Scale N.T.S
Title:
Card
Digital Router
02R Meters
IDC26
P5
Card
VCSCo m
Fader
P2
DB 2 5
Monitor Desk
02R (1) & (2)
P4
IDC26
P6
P1
Unless otherwise specified
Digital I/O
IDC40
GPP 1 & 2
IDC26
Midi
IDC10
P3
IDC20
Analog Router Board
Digital Board
Monitor Control
Monitor Inputs
Analog Meters
DBB Analog Board
8CH Inserts
DBA Analog Board
DIN96 Connectors
Design:
DSP
Phil Scarratt
Drawn :
1998
Date:
7/8/98
Date:
Control Jack's
A.C.N. 052 943 763
PTY LTD
Sheet 1 of 1
CBL-SCH-008-R1
Drawing Number:
MP1 Internal Cable Diagram
Scale N.T.S
Title:
Head phone
Inputs
Dimensions are in millimetres
DO NOT SCALE DRAWING
RCA
Speaker Feeds
Unless otherwise specified
Analog Board
Monitor Phones
Board
Input Analog
Monitor RCA
Analog Board
Monitor Jack
Analog Board
1/4" Jack
RCA's
DIGITAL STUDIO PROCESSING
backpanel
directly on
Connectors are
Monitor XLR
DIN96 Connectors
Bus Connections via
Direct Board to Board
BACK PANEL
XLR's & MINI/TV
Bus Connections via
Analog Bus Board
Analog
Inputs
DBC Analog Board
Direct Board to Board
connections
Ribbon cable
Monitor Desk
BACK PANEL
connector
Desk DB25
Panel Monitor
Cable to Back
DBC Analog Board
DBC Analog Board
DBB Analog Board
DBB Analog Board
DBA Analog Board
DBA Analog Board
Rear View
Monitor Phones Analog Board
Monitor RCA Inputs Analog Board
Monitor Jack Analog Board
Monitor XLR Analog Board
Analog Bus Board
Top View
Monitor XLR Analog Board
Analog Bus Board
Analog Router Board
Digital Monitor Control Board
Power Supply
Design:
DSP
Phil Scarratt
Drawn :
1998
Date:
7/8/98
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
PTY LTD
Sheet 1 of 1
CBL-SCH-009-R1
Drawing Number:
MP1 Internal Layout Diagram
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
Scale N.T.S
Title:
Monitor Control Card.
connectors, except for the Digital
All boards are connected via DIN96
Unless otherwise specified
Notes:
Installation and technical
External System Cable
Diagrams
Installation and Technical Manual
B
screen
Touch-
Monitor
DB15 HD
SVGA
CBL00164
Touchscreen DB9
CBL00149
VGA CABLE DBH15 - DBH15
Mixer
Console
DI/O 1-8 ( A)
DI/O 9-16 ( B)
DEP
Touch I/F
SVGA
CBL00139
CBL00138
DB25
Console DEP
QWERTY
Keyboard
QWERTY
Slot 1
Slot 2
8 Pin Mini-Din
To Host
Design:
DSP
Phil Scarratt
Drawn:
19/12/96
Date:
04/03/98
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
Y2 I/O Tracks 1-8 DB25
Speed Console
Y2 I/O Tracks 9-16 DB25
CBL00137
PTY LTD
Sheet 1 of 1
Drw No.
16 Track D External Cable Diagram
Scale N.T.S
Title:
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
Meter Bridge
O2R
Me ter
Power Supply
CBL00167
DB9
CBL00176
CBL00140
CBL00166
Console
CBL00168
CBL00138
DI/O 1-8 ( A)
Console
K/BRD Chain
Touch I/F
SV GA
Monitor
CBL00101
Touch I/F
Meter Bridge DB15-DB25
GP1
Fader
VGA CABLE DB15 - BNC
CBL00164
H/H+V
R,G,B,V
Y2 I/O channels 1-8 DB25
Keyboard Chain
DB9-PIN
DEP
CBL00149
SV GA
VGA CABLE DB15 - BNC
CBL00164
Touchscreen DB9
CBL00151
Host Port DB9-8 MiniDIN
RS 422
Design:
DSP
Phil Scarratt
Drawn :
19/12/96
Date:
19/12/96
Date:
PTY LTD
Scale N.T.S
Sheet 1 of 1
Drw No.
Diagram
16 Track Postation External Cable
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
screen
Touch-
CBL00150
Title:
Monitor
NLV
Touchscreen DB9
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
H/H+V
Touchscreen DB9
R,G,B,V
CBL00164
screen
VGA CABLE DB15 - BNC
Touch-
CBL00144
SV GA
screen
DI/O 9-16 ( B)
K/BRD Chain
Met er
NLV
8 Pin Mini-Din
Touch-
Y2 I/O 9-16 DB25
DEP
O2R
To Host
Monitor
CBL00139
Midi
Slot 2
Slot 1
K/BRD Chain
H/H+V
Midi
CBL00143
DEP
Console
Meter Bridge
CBL00137
R,G,B,V
VCS
Midi
VC S
Console
Speed Console
QWERTY
CBL00155
Fader Console
QWERTY
Keyboard Console
Touch I/F
CBL00167
CBL00187
Host Port DB9-8 MiniDIN
CBL00188
2nd Host Port DB25-8 MiniDIN
CBL00166
Console
02R( 2)
Midi
CBL00168
Console
K/BRD Chain
Touch I/F
SVGA
(A)
Monitor
Touch I/F
CBL00140
02R Meters
Fad er
VGA CABLE DB15 - BNC
CBL00164
H/H+V
R,G,B,V
CBL00101
Keyboard Chain
K/BRD Chain
32 Track DEP
NLV
DEP
CBL00149
SVGA
VGA CABLE DB15 - BNC
CBL00164
Touchscreen DB9
CBL00151
02R( 1)
Design:
DSP
Phil Scarratt
Drawn :
1998
Date:
10/08/98
Date:
screen
Touch-
A.C.N. 052 943 763
PTY LTD
Sheet 1 of 1
Drw No.
Diagram
32 Track Postation External Cable
Scale N.T.S
Title:
Monitor
CBL00150
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
H/H+V
Touchscreen DB9
R,G,B,V
CBL00164
screen
NLVHR
O2R
2nd or Slave
Meter
Bridge
Touchscreen DB9
DIGITAL STUDIO PROCESSING
CBL00190
Y2 I/O tracks 25-32 DB25
VGA CABLE DB15 - BNC
Touch-
CBL00144
DB9-PIN
CBL00189
Y2 I/O tracks 17-24 DB25
O2R
SVGA
screen
Midi
CBL00143
CBL00139
Touch-
Midi
DEP
CBL00138
Y2 I/O tracks 1-8 DB25
(B)
Monitor
Both Meter Bridge DB15-DB25
VC S
Console
Speed Console
Console
CBL00137
K/BRD Chain
H/H+V
R,G,B,V
o
Y2 I/O tracks 9-16 DB25
VCS3
o
CBL00155
Q W E R TY
Meter
1st or Master
8 Pin Mini-Din
Slot 2
Slot 1
To Host
DB9
Meter Bridge
Meter
Fader Console
Q W E R TY
Keyboard Console
8 Pin Mini-Din
Slot 1
CBL00176
CBL00176
To Host
Slot 2
Power Supply
Touch I/F
BUS Inputs 1-8
Monitor Desk
Cable Diagram).
postation diagram (32 Track Postation External
IN ADDITION to those shown on the normal
NOTE: The connections shown on this diagram are
VCS3
BUS Output Slot
BUS Output Slot
Monitor Outputs 1-8
2nd O2R
(tracks 17-32)
1st O2R
(tracks 1-16)
BUS Inputs 9-16
8Ch Input
DB25
8Ch Output
(located in furniture)
Headphones Jack
Speed Monitor Desk
DB9
High Quality DAC
(provided by user)
Design:
DSP
Phil Scarratt
Drawn :
1998
Date:
07/08/98
Date:
Dimensions are in millimetres
DO NOT SCALE DRAWING
Unless otherwise specified
Monitor Desk
Monitor Inputs 1-8
Control Room Phones
PTY LTD
Sheet 1 of 1
Drw No.
Diagram
Postation With MP1 External Cable
A.C.N. 052 943 763
DIGITAL STUDIO PROCESSING
Scale N.T.S
Title:
MP1
Installation and technical
Exploded Furniture and Case
Diagrams
Installation and Technical Manual
C
10
A
8
9
B
5
6
7
11
12
1
C
2
3
4
D
Caseswitch bracket
Casedrive support
5
6
Casefront bracket (short)
Casefront bracket (long)
Caseholddown bracket
Caseback insert
9
10
11
12
Casefront (Editor, NLV,VCS)
Casemounting ears
4
8
Caseback (Editor,NLV,VCS,NLV hr)
3
Casedrive bayassembly
Casetop
2
7
Casebase assembly
Description
1
Item
E
678-019
678-012
678-008
678-043
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.678.044
PROJECTNo.
CASEASSEMBLY
DRAWING
CASE
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
(02)93616477
REV.DATE
17/12/96
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
1:2
SCALE
.
DATE
25/11/96
A.McLaren
CHECKED
By: A.McL
Stanmore NSW 2048
FAX:0295198094
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
ReleaseforProduction
Rev. 1 Date:25/11/96
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
By: A.McL
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Suedeurethane
Midgrey
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
Reflexblue
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Finishspecs.
Rev. 2 Date:17/12/96
678-011,021,022
678-018
678-035
678-015
678-009
678-002,023,024, 038
678-016
678-017
Drawing no.
F
2
1
A
B
10
6
11
C
9
7
8
5
D
4
3
Pulley
Desktopspacer
Numberpad foam
Track pad foam
8
9
10
11
DISCUSSION
PRODUCTION
PROTOTYPE
QUOTATION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.645.061
PROJECTNo.
SPEED DESK ASSEMBLY
DRAWING
(02)93616477
REV.DATE
16/12/96
VIDEO EDITING WORKSTATION
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
.
DATE
2/12/96
A.McLaren
CHECKED
DATE
Unit2, 7-9BridgeRd
TEL:0295572292
DRAWN
Stanmore NSW 2048
FAX:0295198094
Date: 2/12/96 By: A.McL
ReleaseforProduction
Rev.1
Natural
Natural
Natural
Natural
Urethane
DSPgrey
Natural
Natural
Natural
Natural
Powdercoat
DULUXMetaliccharcoal
Suedeurethane
Midgrey
Finishspec.
F
Date: 16/12/96 By: A.McL
677-012
677-010
677-013
677-015
677-009
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
Rev.2
Joggle wheel
7
645-031
Postation speed deskrest plate
645-030
6
Postation speed deskbrace
4
645-029
Postation speed deskspeed pad foam 677-011
Postation speed deskchassis
3
645-010
645-007
Drawing no.
5
Postation desk tray
Postation speed desk
Description
2
1
Item
E
2
1
A
B
11
12
7
C
10
8
6
9
D
5
4
3
Speedconsole interface bracket
Speedconsole rest plate
Speedconsole jogglewheel
Speedconsole pulley
Speedconsole desk topspacer
Speedconsole number padfoam
Speedconsole track padfoam
7
8
9
10
11
12
Speedconsole speedpadfoam
5
6
Speedconsole brace
Speedconsole chassis
3
4
Speedconsole tray
Speedconsole desk top
Description
2
1
Item
E
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.677.026
PROJECTNo.
SPEED ASSEMBLY
DRAWING
SPEED
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
(02)93616477
REV.DATE
17/12/96
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
.
DATE
27/11/96
A.McLaren
CHECKED
By: A.McL
Stanmore NSW 2048
FAX:0295198094
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
ReleaseforProduction
Rev. 1 Date:27/11/96
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
By: A.McL
Natural
Natural
Natural
Natural
Urethane
DSPgrey
Natural
Natural
Natural
Natural
Natural
Suedeurethane
Midgrey
Suedeurethane
Midgrey
Finishspec.
Rev. 2 Date:17/12/96
677-012
677-010
677-013
677-015
677-009
677-006
677-005
677-011
677-003
677-002
677-004
677-001
Drawing no.
F
A
1
B
6
C
4
3
2
5
D
645-059
645-063
645-064
743-007
645-046
Postation extended desktray
Postation fader control support
Postation fader control centre support
Postation fader bracket
Postation fader rest
2
3
4
5
6
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1997
FILENo.
(02)93616477
2/6/97
REV.DATE
1
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.645.071
PROJECTNo.
FADER DESK ASSEMBLY
DRAWING
VIDEOEDITING WORKSTATION
PROJECT
D3PRODUCTDESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
.
DATE
2/6/97
A.McLaren
CHECKED
By: A.McL
Natural.
Wetspray
Black.
Natural
Wetspray
Black
Powdercoat
DULUXMetalic charcoal
Suedeurethane
Midgrey
Finish spec.
F
Stanmore NSW 2048
FAX:0295198094
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
ReleaseforProduction
Date:2/6/97
645-038
Postation fader desk
Rev.1
Drawing no.
Description
1
Item
E
A
6
1
B
C
5
4
3
2
D
Powdercoat
DULUXMetalic charcoal
Suedeurethane
Midgrey
Suedeurethane
Midgrey
Natural
645-010
645-043
645-040
645-041
Postation desktray
Postation keyboard deskaccessory panel
Postation keyboard deskaccessory surround
Postation keyboard deskbackbracket
Postation keyboard deskfront support
2
3
4
5
6
Date:16/12/96
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.645.062
PROJECTNo.
16/12/96
REV.DATE
(02)93616477
KEYBOARD DESK ASSEMBLY
DRAWING
VIDEO EDITING WORKSTATION
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
DATE
3/12/96
A.McLaren
.
CHECKED
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
By:A.McL
By:A.McL
Stanmore NSW 2048
FAX:0295198094
Date:3/12/96
ReleaseforProduction
Rev.1
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
Rev.2
Natural
Suedeurethane
Midgrey
645-009
Postation keyboard desk
645-042
Finish spec.
Drawing no.
Description
F
1
Item
E
2
A
6
10
7
3
B
1
4
9
5
C
8
D
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
645-001
645-002
645-003
645-004
645-005
645-006
Postation monitor hood
Postation deskframe
Postation leg
Postation monitor bracket
Postation monitor tray
Postation monitor faceplate
Postation curves
2
3
4
5
6
7
Powdercoat
DULUXMetalic charcoal
645-017,018
645-023
Postation side(RH & LH)
Postation spacer
9
10
Date:16/12/96
DISCUSSION
PRODUCTION
PROTOTYPE
QUOTATION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.645.060
PROJECTNo.
POSTATION ASSEMBLY
DRAWING
(02)93616477
REV.DATE
16/12/96
VIDEOEDITING WORKSTATION
PROJECT
D3PRODUCTDESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
.
DATE
3/12/96
A.McLaren
CHECKED
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
By: A.McL
By: A.McL
Stanmore NSW 2048
FAX:0295198094
Date:3/12/96
ReleaseforProduction
Rev.1
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
Rev.2
Powdercoat
DULUXMetalic charcoal
645-016
Postation backcurve
8
Powdercoat
DULUXMetalic charcoal
Wetspray
Black
645-019
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Suadeurethane
Midgrey
Drawing no.
Description
Finish spec.
F
1
Item
E
A
1
5
4
3
2
B
C
13
12
6
7
8
9
10
11
D
12
Postation O2R infill panel
Postation O2R hood
Postation O2R back panel
11
13
Postation O2R back cover
10
Postation O2R adjuster base
Postation O2R rearbracket
6
Postation O2R adjuster top
Postation O2R lower tray
5
9
Postation O2R knee tray
4
8
Postation O2R under tray
3
Continuous grommet
Postation O2R frame
2
7
Postation leg
Description
1
Item
E
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1996
FILENo.
2
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.734.012
PROJECTNo.
O2R DESK ASSEMBLY
DRAWING
O2R DESK
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
(02)93616477
REV.DATE
16/12/96
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
1:1
SCALE
.
DATE
25/11/96
A.McLaren
CHECKED
By:A.McL
Stanmore NSW 2048
FAX:0295198094
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
Release forProduction
Rev. 1 Date: 25/11/96
Adddimensions andfinishspecs.
Add'Postation' texttodescriptions.
By:A.McL
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Suedeurethane
Midgrey
Suedeurethane
Midgrey
Natural
Natural
Natural
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Powdercoat
DULUXMetalic charcoal
Finish specs.
Rev. 2 Date: 16/12/96
734-002
734-001
734-010
734-011
734-008
734-007
734-009
734-006
734-005
734-003
734-004
645-003
Drawing no.
F
4
A
B
6
5
C
2
1
3
D
Powdercoat
DULUXMetallic charcoal
645-049
645-050
Postation table front rail
Postation kneeplate support (right)
Postation kneeplate support (left)
4
5
6
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1997
FILENo.
(02)93616477
3/6/97
REV.DATE
1
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.645.072
PROJECTNo.
TABLE TOPASSEMBLY
DRAWING
VIDEO EDITING WORKSTATION
PROJECT
D3PRODUCT DESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
NTS
SCALE
.
DATE
3/6/97
A.McLaren
Stanmore NSW 2048
FAX:0295198094
DATE
Unit2, 7-9BridgeRd
TEL:0295572292
DRAWN
CHECKED
Powdercoat
DULUXMetallic charcoal
Suedeurethane
Midgrey
Date: 3/6/97 By:A.McL
ReleaseforProduction
Rev.1
645-052
Suedeurethane
Midgrey
645-048
Postation table side rail
3
Suedeurethane
Midgrey
645-053
Postation table rearrail
2
Suedeurethane
Midgrey
Finishspec.
645-037
Drawing no.
Postation table top
Description
F
1
Item
E
A
B
C
5
2
3
4
D
Rack desklowertrim
5
1
Rack desktoptrim
Rack desksidetrim
3
4
Rack desktray assembly
2
Description
Rack desktop
1
Item
E
Drawing no.
774-007
774-006
774-005
774-004
774-001
PRODUCTION
PROTOTYPE
QUOTATION
DISCUSSION
© 1997
FILENo.
(02)93616477
15/7/97
REV.DATE
1
REV. #
D3PRODUCTDESIGNPTYLTD
PowerMac2
D3.774.009
PROJECTNo.
DESKASSEMBLY
DRAWING
RACKDESK
PROJECT
D3PRODUCTDESIGN
DESIGNCONSULTANTS
CHECKISSUEANDDATEPRIORTOCOMMENCEMENT.
DESTROY OR RETURN OBSOLETE DRAWINGS.
DO NOT SCALE.
REPORT DISCREPANCIES.
1:2
SCALE
.
DATE
15/7/97
A.McLaren
CHECKED
DATE
DRAWN
Unit2, 7-9BridgeRd
TEL:0295572292
By: A.McL
Stanmore NSW 2048
FAX:0295198094
Date:15/7/97
ReleaseforProduction
Rev.1
Suedeurethane
Midgrey.
Suedeurethane
Midgrey.
Suedeurethane
Midgrey.
Powdercoat
DULUXMetalic charcoal
Suedeurethane
Midgrey.
Finish specs.
F
">