Ascon Tecnologic K32 Controller and Mini-programmer Quick Guide

K32

Controller and

Mini-programmer

Quick Guide -Code: FK32ENG09

Ascon Tecnologic S.r.l

Via Indipendenza, 56

27029 Vigevano (PV) - ITALY

Tel.: +39 0381 69871

FAX: +39 0381 698730 http:\\www.ascontecnologic.com

[email protected]

1 - OUTLINE DIMENSIONS (mm)

78

K 32

5.5

64

Brackets

71

2 - CONNECTION DIAGRAM

PTC-NTC

Pt100

TC/mV

0... 50/60 mV; 0... 1 V;

0/1... 5 V; 0/2... 10 V

0/4... 20 mA active

Ext.

gen.

4... 20 mA active

4... 20 mA passive (2 wires)

OUT 12VDC (max. 20 mA)

Digital input

DI1 DI2 RS485

B GND A

INPUT

RELAY: 8A-AC1 (3A-AC3)/250VAC SSR: 10mA/10VDC

Power supply

OUT4 OUT3 OUT2 OUT1

Note: The complete manual is available, free of charge, at:

www.ascontecnologic.com

2.1 Mounting requirements

This instrument is intended for permanent installation, for indoor use only, in an electrical panel which encloses the rear housing, exposed terminals and wiring on the back. Select a mounting location having the following characteristics:

1. It should be easily accessible;

2. There is minimum vibrations and no impact;

3. There are no corrosive gases;

4. There are no water or other fluid (condensation);

5. The ambient temperature is in accordance with the operative temperature (0... 50°C);

6. The relative humidity is in accordance with the instrument specifications (20... 85%).

The instrument can be mounted on panel with a maximum thickness of 15 mm.

When the maximum front protection (IP65) is desired, the optional gasket must be monted.

2.2 Genereal notes about wiring

1. Do not run input wires together with power cables;

2. External components (like zener barriers, etc.) connected between sensor and input terminals may cause errors in measurement due to excessive and/or not balanced line resistance or possible leakage currents;

3. When a shielded cable is used, it should be connected at one point only;

4. Pay attention to the line resistance; a high line resistance may cause measurement errors;

5. To avoid electrical shock, connect power at last;

6. For supply connections use No 16 AWG or larger wires rated for at last 75°C;

7. Use copper conductors only;

8. Before connecting the instrument to the power line, make sure that line voltage is equal to the voltage shown on the identification label.

9. The power supply input is NOT fuse protected.

Please, provide a T type 1A, 250 V fuse externally.

3 - CONFIGURATION PROCEDURE

3.1 How to enter the configuration mode

1. Push the button for more than 3 seconds.

The display will show alternately 0 and PASS;

2. Using and/or buttons set the programmed password.

Notes:

a) The factory default password for configuration parameters is 30.

b) The parameter changes are protected by a time out. If no key is pressed for more than 10 seconds the instrument automatically returns back to the Standard display, the new value of the last selected parameter will be lost and the parameter modification procedure closed.

Sometimes can be useful to enter the parameter configuration procedure with no timeout

(e.g. for the first time an instrument is configured). In this case, use a password equal to the previously set password + 1000 digits (e.g.

1000 + 30 [default] = 1030).

It is always possible to manually end the parameter configuration procedure (see the next paragraph).

c) During parameter modification the instrument continues performing the control.

In certain conditions, when a configuration change can produce a heavy bump to the process, it is advisable to temporarily stop the control procedure during the programming procedure (the control output will be OFF).

In this case use a password equal to the previously set password + 2000 digits

(e.g. 2000 + 30 [default] = 2030).

The control procedure will automatically restart when the configuration procedure will be manually closed.

3. Push the button

If the password is correct the display will show the acronym of the first parameter group preceded by the symbol .

In other words the display will show

The instrument is in configuration mode.

.

3.2 How to exit the configuration mode

Push button for more than 5 seconds. The instrument will come back to the “standard display”.

3.3 Keyboard functions during parameters modification

A short pression allows to exit the current parameter group and select a new parameter group.

A long pression allows to close the configuration parameter procedure (the instrument returns to the “standard display”).

When the display is showing a group, the key allows to enter in the selected group.

When the display is showing a parameter, the key allows you to store the value shown and go to the next parameter within the same group.

Increases the value of the selected parameter.

Decreases the value of the selected parameter.

Note: The group selection is cyclic as well as the selection of the parameters in a group.

3.4 Factory reset - Default parameters loading procedure

Sometimes, e.g. when you reconfigure an instrument previously used for other works or from other people or when you have made too many errors during configuration and you decided to reconfigure the instrument, it is possible to restore the factory configuration.

This action allows you to put the instrument in a defined condition (in the same condition it was at the first Power ON).

The default data are the typical values loaded in the instrument prior to shipping from factory. To load the factory default parameter set, proceed as follows:

1. Press the button for more than 5 seconds;

2. The display will show alternately “PASS” and “0”;

3. Using and buttons, set the value -481;

5. The instrument will turn OFF all LEDs then it will show “dFLt” messages and than it turn ON all

LEDs of the display for 2 seconds and than it will restart as at the first power ON.

The procedure is complete.

4 - OPERATIVE MODES

4.1 Keyboard function when the instrument is in Auto mode

Performs the action programmed by [116] uSrb

( button function during RUN TIME) parameter.

Enters the parameter modification procedures.

Starts the "Direct set point modification" function (see below).

Displays the "Additional information"

(see below).

4.2 Direct set point modification

This function allows to modify rapidly the set point value selected by [79] SPAt or to the set point of the segment group currently in progress. The instrument is showing the "standard display".

1. Push button. The display will show alternately the acronym of the selected set point (e.g. SP2) and its value.

Note: When the programmer is running, the instrument will show the set point of the group currently in use.

2. By and buttons, assign to this parameter the desired value.

3. Do not push any button for more than 5 second or push the button. In both cases the instrument memorize the new value and come back to the "standard display".

Note: If the selected set point has not been promoted to the Operator level, the instrument allows you to see the value but not to modify it.

4.3 Additional information

This instrument is able to show you some additional information that can help you to manage your system.

1. When the instrument is showing the "standard display" push button. The display will show "H" or

"c" followed by a number. This value is the current power output applied to the process. "H" means

Heating action while "c" means Cooling action.

2. Push button again. When the programmer is running the instrument will show the segment currently performed and the Event status as shown below: where the first figure can be "r" for a ramp or "S" for a soak, the next digit show the number of the segment (ex. S3 indicates stasis 3) and the two less significant digits show you the status of the two event (LSD is the Event 2).

3. Push button again. When the programmer is running the instrument will show the theoretical remaining time to the end of the program preceded by a P letter:

4. Push button again. When the wattmeter function is running the instrument will show "U" followed by the measured energy.

Note: The energy calculation will be in accordance with the [126] Co.tY parameter setting.

5. Push button again. When the "Worked time count" is running the instrument will show "d" for days or "h" for hours followed by the measured time.

6. Push button again. The instrument will come back to the "standard display".

Note: The additional information visualization is subject to a time out of 10 seconds.

5 - ERROR MESSAGES

5.1 Out of Range Signals

The display shows the OVER-RANGE and UNDER-

RANGE conditions with the following indications:

Over-range Under-range

The sensor break will be signalled as an out of range:

Note: When an over-range or an under-range is detected, the alarms operate as in presence of the maximum or the minimum measurable value respectively.

To check the out of span Error condition, proceed as follows:

1. Check the signal source and the connecting line.

2. Make sure that the input signal is in accordance with the instrument configuration. Otherwise, modify the input configuration (see section 4).

3. If no error is detected, send the instrument to your supplier to be checked.



WARNING

Whenever a failure or a malfunction of the device may cause dangerous situations for persons, things or animals, please remember that the plant must be equipped with additional safety devices which will guarantee safety.

4 - PARAMETERS TABLES

]

InP group (parameters relative to the inputs)

5.2 List of possible errors

ErAT - Fast Auto-tune cannot start. The measure value is too close to the set point. Push the button in order to delete the error message.

NoAt - Auto-tune not finished within 12 hours.

ErEP- Possible problem of the instrument memory.

The message desappears automatically. If the error continues, send the instrument to the supplier.

6 - GENERAL NOTES

6.1 Proper Use

Every possible use not described in the complete manual (www.ascontecnologic.com) must be considered as a improper use.

This instrument is in compliance with EN 61010-1

"Safety requirements for electrical equipment for measurement, control and laboratory use"; for this reason it coud not be used as a safety equipment.

Ascon Tecnologic S.r.l. and its legal representatives do not assume any responsibility for any damage to people, things or animals deriving from violation, wrong or improper use or in any case not in compliance with the instrument's features.

6.2 Warranty and repairs

This product is under warranty against manufacturing defects or faulty materials that are found within 12 months from delivery date.

The warranty is limited to repairs or to the replacement of the instrument.

The tampering of the instrument or an improper use of the product will bring about the immediate withdrawal of the warranty's effects.

In the event of a faulty instrument, either within the period of warranty, or further to its expiry, please contact our sales department to obtain authorisation for sending the instrument to our company.

The faulty product must be shipped to Ascon Tecnologic with a detailed description of the faults found, without any fees or charge for Ascon Tecnologic, except in the event of alternative agreements.

Before supplying tension to the instrument, make sure that it is perfectly dry.

1

2

3

4

5

6

7

8

9 no.

10

11

Par.

HcFG

SEnS

SSc

FSc unit

FiL inE oPE diF1 diF2

Description

It shows the current hardware

Range

TC/RTD, TC/PTC, Current, Voltage

Default Vis. Promo.

According to the HW

Not displayed

Sensor selection (according to the HW)

TC, Pt100 input

TC, PTC, NTC input

I input

V input

Initial scale readout

Final scale readout

Engineering unit

Digital filter on the measured value

Selection of the Sensor Out of Range type that will enable the safety output value

Safety output value

Digital input 1 function

Digital input 2 function

J, crAL, S , r, t, ir.J, ir.cA, Pt1, 0... 50 (mV),

0... 60 (mV), 12... 60 (mV)

J, crAL, S , r, t, Ir.J, Ir.cA, Ptc, ntc, 0... 50 (mV),

0... 60 (mV), 12... 60 (mV)

0... 20 (mA), 4... 20 (mA)

J

Ptc

4.20

0... 5(V), 1... 5(V), 0... 10(V), 2... 10(V), 0... 1 (V) 0.10

0... 3 0

From -1999 to FSC (E.U.)

From SSc to 9999 (E.U.)

°C or °F

-1999

9999

0 = °C

1.0

From 0 (OFF)... 20.0 (s) or = Over-range ur = Under-range our = Over and Under

-100... 100 (%)

7 =

8 =

9 =

10 =

11 =

12 =

13 =

14 = oFF = No function

1 =

2 =

Alarm Reset

Alarm acknowledge (ACK)

3 =

4 =

5 =

6 =

Hold of the measured value

Stand by mode

HEAt with SP1 and CooL with “SP2”

Timer run/hold/reset [transition]

15 =

16 =

17 =

18 =

19 =

20 =

Timer run [transition]

Timer reset [transition]

Timer run/hold [Status]

Program run

Program reset

Program hold

Program run/hold

Program run/reset

Instrument in Manual mode

Sequential set point selection

SP1/SP2 selection

Set point Binary selection

Digital inputs in parallel to the

UP and DOWN keys

Timer RUN/Reset

See diF1 our

0 nonE nonE

A-4

A-5

A-6

A-7

A-8

C-0

C-0

C-0

A-13

A-14

]

Out Group (parameters relative to the outputs)

no.

Par.

12

13

14

15

16 o1F Out 1 function o1AL Alarms linked up with out 1 o1Ac Out 1 action

Description o2F Out 2 function o2AL Alarms linked up with the out 2

Range

NonE = Output not used

H.rEG = Heating output c.rEG = Cooling output

AL = Alarm output t.out = Timer output t.HoF = Timer out -OFF in hold

P.End = Program end indicator

P.HLd = Program hold indicator

P. uit = Program wait indicator

P.run = Program run indicator

P.Et1 = Program Event 1

P.Et2 = Program Event 2 or.bo = Out-of-range or burn out indicator

P.FAL = Power failure indicator bo.PF = Out-of-range, burn out and Power failure indicator diF.1 = DO repeats the DI1 status diF.2 = DO repeats the DI2 status

St.bY = Stand by status indicator on = Out 1 ever ON

0... 31

+1 =

+2 =

+4 =

Alarm 1

Alarm 2

Alarm 3

+8 = Loop break alarm

+16 = Sensor Break (burn out) dir = Direct action rEU = Reverse action dir.r = Direct with reversed LED

ReU.r = Reverse with reversed LED

See: 12 - o1F: Out1 functions

See: 13 - o1AL: Alarms linked up with out 1

Default

H.reg

AL1 dir

Vis. Promo.

A-16

A-17

C-0

AL A-19

+1 = AL1 A-20

no.

Par.

21

22

23

17

18

19

20

Description o2Ac Out 2 action o3F Out 3 function o3AL Alarms linked up with the out 3 o3Ac Out 3 action o4F Out 4 function o4AL Alarms linked up with the out 4 o4Ac Out 4 action

Range

See: 14 - o1Ac: Out 1 action

See: 12 - o1F: Out1 functions

See: 13 - o1AL: Alarms linked up with out 1

See: 14 - o1Ac: Out 1 action

See: 12 - o1F: Out1 functions

See: 13 - o1AL: Alarms linked up with out 1

See: 14 - o1Ac: Out 1 action

]

AL1 Group (parameters relative to AL1 - alarm 1)

Default Vis. Promo.

dir C-0

AL A-22

+2 = AL2 A-23 dir C-0

AL A-24

+3 = AL3 A-25 dir C-0 no.

24

25

26

27

28

29

30

31

Par.

AL1t

Ab1

Alarm 1 type

Description

Alarm 1 function

Range nonE = Alarm not used

LoAb = Absolute low alarm

HiAb = Absolute high alarm

LHAb = Absolute band alarm

SE.br = Sensor Break

LodE = Deviation low alarm (relative)

HidE = Deviation high alarm (relative)

LHdE = Relative band alarm

0... 15

+1 =

+2 =

+4 =

+8 =

Not active at power ON

Latched alarm (manual reset)

Acknowledgeable alarm

Relative alarm not active at set point change

Default

LoAb

Vis. Promo.

A-47

0 C-0

AL1L

For High and low alarms, it is the low limit of the AL1 threshold

For band alarm, it is low alarm threshold

AL1H

For High and low alarms, it is the high limit of the AL1 threshold

For band alarm, it is high alarm threshold

AL1 threshold AL1

HAL1 AL1 hysteresis

AL1d AL1 delay

AL1o

Alarm 1 enabling during Stand-by mode and out of range conditions

From -1999 to AL1H (E.U.)

From AL1L to 9999 (E.U.)

-1999

9999

From AL1L to AL1H (E.U.)

1... 9999 (E.U.)

From 0 (OFF) to 9999 (s)

0 =

1 =

2 =

3 =

Alarm 1 disabled during Stand-by and out of range

Alarm 1 enabled in stand by mode

Alarm 1 enabled in out of range condition

Alarm 1 enabled in stand by mode and in overrange condition

0

1 oFF

0

A-48

A-49

A-50

A-51

C-0

C-0

]

AL2 Group (parameters relative to AL2 - alarm 2)

Default Vis. Promo.

LoAb A-54

0 C-0

36

37

38 no.

Par.

32

33

34

35

39

AL2t

Ab2

AL2L

AL2H

Alarm 2 type

Alarm 2 function

Description

For High and low alarms, it is the low limit of the AL2 threshold

For band alarm, it is low alarm threshold

For High and low alarms, it is the high limit of the AL2 threshold

For band alarm, it is high alarm threshold

AL2

AL2o

AL2 threshold

HAL2 AL2hysteresis

AL2d AL2 delay

Alarm 2 enabling during Stand-by mode and out of range conditions

Range

See: 24 - Ab1t: Alarm 1 Type

See: 25 - AL1f: Alarm 1 function

See: 26 - AL1L

See: 27 - AL1H

See: 28 - AL1: Alarm 1 threshold

See: 29 - HAL1: Alarm 1 hysteresis

See: 30 - AL1d: AL1 delay

See: 31 - AL1o:Alarm 1 enabling during Stand-by mode and out of range conditions

]

AL3 Group (parameters relative to AL3 - alarm 3)

-1999

9999

0

1 oFF

0

A-56

A-57

A-58

A-59

C-0

C-0

44

45

46 no.

Par.

40

41

42

43

47

AL3t

Ab3

AL3L

Alarm 3 type

Alarm 3 function

Description

For High and low alarms, it is the low limit of the AL3 threshold

For band alarm, it is low alarm threshold

AL3H

AL3

For High and low alarms, it is the high limit of the AL3 threshold

For band alarm, it is high alarm threshold

AL3 threshold

HAL3 AL3hysteresis

AL3d AL3 delay

AL3o

Alarm 3 enabling during Stand-by mode and out of range conditions

Range

See: 24 - Ab1t: Alarm 1 Type

See: 25 - AL1f: Alarm 1 function

See: 26 - AL1L

See: 27 - AL1H

See: 28 - AL1: Alarm 1 threshold

See: 29 - HAL1: Alarm 1 hysteresis

See: 30 - AL1d: AL1 delay

See: 31 - AL1o:Alarm 1 enabling during Stand-by mode and out of range conditions

]

LBA Group

48

49

50 no.

Par.

Description

LbAt LBA time

LbSt Δ measure for LBA during Soft start

LbAS Δ measure for LBA

51 LbcA Condition for LBA enabling

Range

From 0 (oFF) to 9999 (s)

From 0 (oFF) to 9999 (E.U.)

1... 9999 (E.U.) uP = Active when Pout = 100% dn = Active when Pout = -100% both = Active in both cases

]

rEG Group

Default Vis. Promo.

LoAb C-0

0 C-0

-1999

9999

0

1 oFF

0

C-0

C-0

C-0

C-0

Default Vis. Promo.

oFF

10

20

C-0

C-0

C-0 both

C-0

C-0

C-0

66

67

68

56

57

58

59

60

61 no.

Par.

52

53

54

55

62

63

64

65

69

70

71

Description Range cont Control type

Auto Autotuning selection

Aut.r

SELF

Manual start of the Autotuning

Self tuning enabling

Pid = PID (heat and/or)

On.FA = ON/OFF asymmetric hysteresis

On.FS = ON/OFF symmetric hysteresis nr = Heat/Cool ON/OFF control with neutral zone

-3 =

-2 =

-1 =

0 =

1 =

2 =

3 =

4 =

-4 = Oscillating auto-tune with automatic restart at power ON and after all point change

Oscillating auto-tune with manual start

Oscillating tune with automatic start at first power ON only

Oscillating autotune with auto restart at each power ON

Not used

Fast auto tuning with auto restart at each power ON

Fast auto-tune with auto start at first power ON only

FAST auto-tune with manual start

FAST auto-tune with automatic restart at power ON and after a set point change oFF = Not active on = Active

YES = The instrument do not perform the self-tuning no = The instrument is performing the self-tuning

HSEt Hysteresis of the ON/OFF control 0... 9999 (E.U.) cPdt Time for compressor protection From 0 (oFF) to 9999 (s)

Pb int

Proportional band

Integral time

0... 9999 (E.U.)

From 0 (oFF) to 9999 (s) dEr Derivative time

Fuoc Fuzzy overshoot control

H.Act

Heating output actuator

From 0 (oFF) to 9999 (s)

0.00... 2.00

SSr = SSR rELY = Relay

SLou = Slow actuators tcrH Heating output cycle time

PrAt

Power ratio between heating and cooling action

0.1... 130.0 (s)

0.01... 99.99

c.Act

Cooling output actuator

SSr = SSR rELY = Relay

SLou = Slow actuators

0.1... 130.0 (s) tcrc Cooling output cycle time rS od

Manual reset (Integral pre-load) -100.0... +100.0 (%)

Delay at power ON From 0.00 (oFF) to 99.59 (hh.mm)

St.P

Maximum power output used during soft start

-100... 100 (%)

SSt Soft start time From 0.00 (oFF) to 8.00 (inF)(hh.mm)

SStH Threshold for soft start disabling -1999... +9999 (E.U.)

]

SP Group

no.

Par.

76

77

78

79

72

73

74

75

Description nSP Number of used set points

SPLL Minimum set point value

SPHL Maximum set point value

SP 1 Set point 1

SP 2 Set point 2

SP 3 Set point 3

SP 4 Set point 4

SPAt Selection of the active set point.

80 SP.rt

Remote set point type

Default Vis. Promo.

Pid

2 oFF no

1 oFF

50

200

50

0.50

SSr

20.0

1.00

SSr

20.0

0.0

oFF

0 oFF

9999

A-25

C-0

A-26

C-0

A-27

C-0

A-28

A-29

A-30

A-31

A-32

C-0

A-34

A-35

C-0

C-0

C-0

C-0

C-0

C-0

Range Default Vis. Promo.

1... 4

From -1999 to SPHL

From SPLL to 9999

From SPLL to SPLH

From SPLL to SPLH

From SPLL to SPLH

From SPLL to SPLH

From 1 (SP 1) to nSP

RSP = The value coming from serial link is used as remote set point trin = The value will be added to the local set point selected by SPAt and the sum becomes the operative set point

PErc = The value will be scaled on the input range and this value will be used as remote set point trin

0

1

0

0

1

-1999

9999

0

A-38

A-39

A-40

O-41

O-42

O-43

O-44

O-45

C-0 no.

Par.

81

82

83

Description Range

SP.Lr Local/remote set point selection

Loc = local rEn = remote

SP.u

Rate of rise for POSITIVE set point change 0.01... 100.00 (inF) Eng. units per minute

SP.d

Rate of rise for NEGATIVE set point change 0.01...100.00 (inF) Eng. units per minute

]

Tin Group

no.

Par.

84 tr.F

85 tr.u

Timer unit

86 tr.t1

Time 1

87 tr.t2

Time 2

88 tr.St

Timer status

Description

Independent timer function

Range

NonE = Timer not used i.d.A = Delayed start timer i.uP.d = Delayed start at power up i.d.d = Feed-through timer i.P.L = Asymmetrical oscillator, start OFF i.L.P = Asymmetrical oscillator, start ON hh.nn = Hours and minutes nn.SS = Minutes and seconds

SSS.d = Second and tenth of seconds

When tr.u < 20: 0.01... 99.59

When tr.u = 200: 0.1... 995.9

When tr.u < 2: 00.00 (oFF)... 99.59 (inF)

When tr.u = 2: 000.0 (oFF)... 995.9 (inF) rES = Timer reset run = Timer run

HoLd = Timer hold

]

Prg Group

C-0

C-0 no.

Par.

Description Range Default Vis. Promo.

89

90

Pr.F

Pr.u

Program action at power ON

Engineering unit of the soak nonE = Programmer not used

S.uP.d = Start at power ON with a first step in stand-by

S.uP.S = Start at power ON u.diG = Start at Run command detection only u.dG.d = Start at Run command with a first step in stand-by nonE hh.nn = Hours and minutes nn.SS = Minutes and seconds hh.nn

91 Pr.E

Instrument behaviour at the end of the program execution cnt = Continue

SPAt = Go to the set point selected by SPAt

St.by = Go to stand-by mode

92 Pr.Et

Time of the end program indication From 0.00 (oFF) to100.00 (inF) minutes and seconds

93 Pr.S1

Set point of the first soak

94 Pr.G1

Gradient of the first ramp

95 Pr.t1

Time of the first soak

SPAt

From SPLL to SPHL oFF

0

0.1... 1000.0 (inF= Step transfer) Engineering Unit/minute inF

0.00... 99.59 0.10

96 Pr.b1

Wait band of the first soak

97 Pr.E1

Events of the first group

98 Pr.S2

Set point of the second soak

From 0 (oFF) to 9999 (E.U.)

00.00... 11.11

OFF or from SPLL to SPHL oFF

00.00

0

99 Pr.G2

Gradient of the second ramp

100 Pr.t2

Time of the second soak

101 Pr.b2

Wait band of the second soak

102 Pr.E2

Events of the second group

103 Pr.S3

Set point of the third soak

104 Pr.G3

Gradient of the third ramp

105 Pr.t3

Time of the third soak

106 Pr.b3

Wait band of the third soak

107 Pr.E3

Events of the third group

108 Pr.S4

Set point of the fourth soak

109 Pr.G4

Gradient of the fourth ramp

110 Pr.t4

Time of the fourth soak

111 Pr.b4

Wait band of the fourth soak

112 Pr.E4

Events of the fourth group

113 Pr.St

Program status

0.1... 1000.0 (inF= Step transfer) Engineering Unit/minute inF

0.00... 99.59

From 0 (oFF) to 9999 (E.U.)

00.00... 11.11

OFF or from SPLL to SPHL

0.10

oFF

0.1... 1000.0 (inF= Step transfer) Engineering Unit/minute inF

0.00... 99.59

0.10

From 0 (oFF) to 9999 (E.U.)

00.00... 11.11

OFF or from SPLL to SPHL

0.1... 1000.0 (inF= Step transfer) Engineering Unit/minute inF

0.00... 99.59

From 0 (oFF) 9999 (E.U.)

00.00... 11.11

rES = Program reset run = Program start

HoLd = Program hold

00.00

0 oFF

00.00

0

0.10

oFF

00.00

0

A-67

A-68

A-71

C-0

A-79

A-80

A-81

C-0

A-83

A-84

A-85

A-86

C-0

A-88

A-72

A-73

A-74

A-75

A-76

C-0

A-78

A-89

A-90

A-91

C-0

]

PAN Group

Default Vis. Promo.

20

30

A-93

C-0 no.

Par.

Description

114 PAS2 Password level 2

115 PAS3 Password level 3

116 uSrb

117 diSP

118 AdE

119 FiLd

button function during run time

Display management

Bargraph deviation

Filter on the displayed value

120 dSPu Status of the instrument at power up

121 oPr.E

122 oPEr

Operative mode enabling

Operative mode selection

Range

From 0 (oFF) to 999

1... 999 nonE = Not used tunE = Starts auto tuning functions oPLo = Manual mode (OPLO)

AAc = Alarm reset

ASi = Alarm acknowledge chSP = Sequential set point selection

St.by = Stand-by mode

Str.t = Run/hold/reset timer

P.run = Program start

P.rES = program reset

P.r.H.r = Run/hold/reset program nonE = Standard display

Pou = Power output

SPF = Final set point

Spo = Operative set point

AL1 = Alarm 1 threshold

AL2 = Alarm 2 threshold

AL3 = Alarm 3 threshold

Pr.tu = Program time up

Pr.td = Program time down

P.t.tu = Program total time up

P.t.td = Program total time down ti.uP = Timer time up ti.du = Timer time down

Perc = Percent of the power output during soft start

From 0 (oFF) to 9999

From 0.0 (oFF) to 20.0

AS.Pr = Starts as it was prior to the power down

Auto = Starts in Auto mode oP.0 = Starts in manual mode with a power output =0

St.bY = Starts in stand-by mode

ALL = All

Au.oP = Autp or manual (oPLo) only

Au.Sb = Auto and Stand by only

Auto = Automatic oPLo = Manual

St.by = Stand-by

]

SER Group

nonE

2 oFF

AS.Pr

ALL

Auto

A-94

A-95

A-96

C-0

C-0

C-0

O-1 no.

Par.

123 Add

124 bAud Baud rate

125 trSP

Address

Description

Selection of the value to be retransmitted (Master)

Range

From 0 (oFF) to 254

1200

2400

(bit/s)

(bit/s)

9600 (bit/s)

19.2 (kbit/s)

38.4 (kbit/s) nonE = Not used rSP = Operative set point

PErc = Current power output (%)

]

con Group(Wattmeter)

no.

Par.

Description Range

126 co.ty

Measurement type o =

1 =

2 =

3 =

4 =

5 =

OFF = Not used

Instantaneous (kW)

Power consumption (kW/h)

Energy used during program execution

Total worked days with threshold

Total worked hours with threshold

1... 999 (Volt) 127 UoLt Nominal load voltage

128 cur Nominal load current 1... 999 (A)

129 h.Job

Threshold of the worked hours/days From 0(oFF) to 9999

]

cal Group (user calibration)

no.

Par.

Description

130 A.L.P

Adjust low Point

131 A.L.o

Adjust low Offset

132 A.H.P

Adjust High Point

133 A.H.o

Adjust High Offset

Range

From -1999 to AH.P-10 (E.U.)

-300... +300 (E.U.)

From A.L.P +10 to 9999 (E.U.)

-300... +300 (E.U.)

Default Vis. Promo.

Loc inF inF nonE nn.SS

1.00

1.00

rES

9600 nonE nonE

230

10 oFF

C-0

Default Vis. Promo.

A-62

A-63

A-64

A-65

C-0

1

Default Vis. Promo.

C-0

C-0

C-0

Default Vis. Promo.

A-97

A-98

A-99

A-100

Default Vis. Promo.

0

0

9999

0

A-9

A-10

A-11

A-12