Ascon tecnologic K3 V Series Quick Manual

2.4 K85V Series
KxxV
3.3 Keyboard functions during
parameters modification
0... 50/60 mV; 0... 1 V; 0/1... 5 V; 0/2... 10 V
0/4... 20 mA active
Indicators
with independent Timer option
A short pression allows to exit the current parameter group and select a new parameter group.
A long pression allows to close the configuration parameter procedure (the instrument returns to the “standard display”).
Ext.
gen.
4... 20 mA active
4... 20 mA passive (2 wires)
OUT 10VDC (max. 20 mA)
DI1
Power
supply
PTC-NTC
Pt100
TC
DI2
A
B
GND
RS485
Digital input
Relays: Out-1, 2: 8A-AC1 (3A-AC3)/250VAC
Out-3: 5A-AC1 (2A-AC3)/250VAC
To check the out of span Error condition, proceed as
follows:
When the display is showing a group, the key
allows to enter in the selected group.
When the display is showing a parameter, the
key allows you to store the value shown and go
to the next parameter within the same group.
INPUT
SSR: 20mA/10VDC
Increases the value of the selected parameter.
OUT1
www.ascontecnologic.com
Ascon Tecnologic S.r.l
Via Indipendenza, 56
27029 Vigevano (PV) - ITALY
Tel.: +39 0381 69871
FAX: +39 0381 698730
http:\\www.ascontecnologic.com
[email protected]
2.5 Mounting requirements
This instrument is intended for permanent installation, for indoor use only, in an electrical panel which
encloses the rear housing, exposed terminals and
wiring on the back. Select a mounting location having the following characteristics:
1. It should be easily accessible;
1 - OUTLINE DIMENSIONS (mm)
1.1 K3_V Series
2. There is minimum vibrations and no impact;
3. There are no corrosive gases;
28
64
35
5.5
Brackets
29
Panel + Gasket
12 mm max.
4. There are no water or other fluid (i.e.
condensation);
48
Sometimes, e.g. when you reconfigure an instrument
previously used for other works or from other people
or when you have made too many errors during configuration and you decided to reconfigure the instrument, it is possible to restore the factory configuration.
This action allows you to put the instrument in a defined condition (in the same condition it was at the
first Power ON).
The default data are the typical values loaded in the
instrument prior to shipping from factory. To load the
factory default parameter set, proceed as follows:
1. Press the
button for more than 5 seconds;
3. Using
and
6. The relative humidity is in accordance with the
instrument specifications (20... 85 %)
4. Push
button;
1. Do not run input wires together with power cables;
98
2. External components (like zener barriers, etc.)
connected between sensor and input terminals
may cause errors in measurement due to
excessive and/or not balanced line resistance or
possible leakage currents;
44.5
9.5
3.4 Factory reset - Default parameters
loading procedure
2. The display will show alternately “PASS” and “0”;
2.6 Genereal notes about wiring
1.2 K4_V Series
Decreases the value of the selected parameter.
Note: The group selection is cyclic as well as the
selection of the parameters in a group.
5. The ambient temperature is in accordance with
the operative temperature (0... 50 °C)
The instrument can be mounted on panel with a
maximum thick of 15 mm. When the maximum front
protection (IP65) is desired, the optional gasket
must be monted.
71
48
OUT2
Note: The complete manual is available, free of
charge, at:
Quick Guide -Code: FKxxVENG
78
OUT3
buttons, set the value -481;
5. The instrument will turn OFF all LEDs then it will
show “dFLt” messages and than it turn ON all
LEDs of the display for 2 seconds and than it will
restart as at the first power ON.
The procedure is complete (the default value of
each parameter is listed in the “Parameters Tables” paragraph).
4 - ERROR MESSAGES
4.1 Out of Range Signals
The display shows the OVER-RANGE and UNDERRANGE conditions with the following indications:
1. Check the signal source and the connecting line.
2. Make sure that the input signal is in accordance
with the instrument configuration. Otherwise,
modify the input configuration (see section 4).
3. If no error is detected, send the instrument to
your supplier to be checked.
4.2 List of possible errors
ErEP- Possible problem of the instrument memory.
The message desappears automatically. If the error
continues, send the instrument to the supplier.
5 - GENERAL NOTES
5.1 Proper Use
Every possible use not described in the complete
manual (www.ascontecnologic.com) must be considered as a improper use.
This instrument is in compliance with EN 61010-1
"Safety requirements for electrical equipment for
measurement, control and laboratory use"; for this
reason it coud not be used as a safety equipment.
Ascon Tecnologic S.r.l. and its legal representatives do not assume any responsibility for any
damage to people, things or animals deriving from
violation, wrong or improper use or in any case not
in compliance with the instrument's features.
5.2 Warranty and repairs
This product is under warranty against manufacturing
defects or faulty materials that are found within 12
months from delivery date.
The warranty is limited to repairs or to the replacement of the instrument.
The tampering of the instrument or an improper use of
the product will bring about the immediate withdrawal
of the warranty's effects.
In the event of a faulty instrument, either within the period of warranty, or further to its expiry, please contact
our sales department to obtain authorisation for sending the instrument to our company.
The faulty product must be shipped to Ascon Tecnologic with a detailed description of the faults found,
without any fees or charge for Ascon Tecnologic, except in the event of alternative agreements.
Before supplying tension to the instrument, make sure
that it is perfectly dry.
3. When a shielded cable is used, it should be
connected at one point only;
4. Pay attention to the line resistance; a high line
resistance may cause measurement errors.
Panel + Gasket
9 mm max.
Bracket
type 2
Bracket
type 1
6. The power supply input is NOT fuse protected.
Please, provide a T type 1A, 250 V fuse externally.
1.3 K85V Series
70
1 2 3
4 5
6 7
27
8
21
5. Before connecting the instrument to the power
line, make sure that line voltage is equal to the
voltage shown on the identification label.
12
60
45
84
e) The power supply input is NOT fuse protected.
Please, provide a T type 1A, 250 V fuse externally.
2 - CONNECTIONS DIAGRAMS
2.1 K31V Series
3 - CONFIGURATION PROCEDURE
3.1 How to enter the configuration mode
0... 50/60 mV; 0... 1 V; 0/1... 5 V; 0/2... 10 V
0/4... 20 mA active
4... 20 mA active
1. Push the
button for more than 3 seconds.
The display will show alternately 0 and PASS;
4... 20 mA passive (2 wires)
OUT 12VDC (max. 20 mA)
PTC-NTC
Pt100
TC/mV
DI1
DI2
B
 WARNING!
Whenever a failure or a malfunction of the device may cause dangerous situations for persons,
things or animals, please remember that the plant must be equipped with additional safety devices which will guarantee safety.
4 - PARAMETERS TABLES
]
InP Group (parameters relative to the inputs)
no. Parameter
1
HcFG
2. Using
and/or
buttons set the
programmed password.
RS485
GND A
INPUT
Power
supply
OUT4
OUT3
SSR: 10mA/10VDC
OUT2
OUT1
2.2 K38V Series
RELAY: 8A-AC1 (3A-AC3)/250VAC
SSR: 8mA/8VDC
NC NO C
C
OUT1
NC NO
INPUT
TC/mV
Pt100
PTC-NTC
OUT2
Out 10VDC max. 20mA
4...20 mA passive (2 wires)
4...20 mA active Ext.
gen.
0/4...20 mA active
0...50/60 mV; 0...1 V;
0/1...5 V; 0/2...10 V
2.3 K4_V Series
DI1
DI2
Out1, Out2: Relay 8A-AC1 (3A-AC3)/250VAC
Out3: Relay 5A-AC1 (2A-AC3)/250VAC
SSR: 8mA/8VDC
INPUT
OUT3
Power
supply
OUT2
Out 12 VDC max. 20 mA
4...20 mA passive (2 wires)
Ext. 4... 20 mA active
gen.
0/4...20 mA active
0... 50/60 mV; 0... 1 V; 0/1... 5 V; 0/2... 10 V
OUT1
a) The factory default password for configuration
parameters is 30.
b) The parameter changes are protected by a time
out. If no key is pressed for more than 10 seconds the instrument automatically returns back
to the Standard display, the new value of the last
selected parameter will be lost and the parameter modification procedure closed.
Sometimes can be useful to enter the parameter
configuration procedure with no timeout (e.g. for
the first time an instrument is configured). In
this case, use a password equal to the previously set password + 1000 digits (e.g. 1000 + 30
[default] = 1030).
It is always possible to manually end the
parameter configuration procedure (see the
next paragraph).
c) During parameter modification the instrument
continues to perform the Alarms and timer functions. In certain conditions, when a configuration change can produce a bump to the process,
it is advisable to temporarily stop the alarm
functions during the programming procedure (its
alarms output will be Off).
A password equal to 2000 + the programmed
value (e.g. 2000 + 30 = 2030).
The alarms will restart automatically when the
configuration procedure will be manually closed
3. Push the
button
If the password is correct the display will show
the acronym of the first parameter group
preceded by the symbol .
In other words the display will show
.
The instrument is in configuration mode.
3.2 How to exit the configuration mode
Push
button for more than 5 seconds. The instrument will come back to the “standard display”.
Description
Parameter available by
serial link nIt shows the
current hardware
Range
TC/RTD
TC/PTC
Current
Volt
Default
Vis.
Promo.
According
Not
to the
displayed
Hardware
Sensor selection (according to the hw)
Notes:
RELAYS: Out-1, 2: 8A-AC1 (3A-AC3)/250VAC
RELAYS: Out-3, 4: 5A-AC1 (2A-AC3)/250VAC
TC
Pt100
PTC-NTC
b) For supply connections use No. 16 AWG or larger wires rated for at last 75°C;
d) Before connecting the instrument to the power
line, make sure that line voltage is equal to the
voltage shown on the identification label.
13 14 15 16 17 18 19 20 21 22 23 24
Power
supply
Note: When an over-range or an under-range is
detected, the alarms operate as in presence of
the maximum or the minimum measurable
value respectively.
c) Use copper conductors only;
Out3
Ext.
gen.
Under-range
Notes:Safety precautions.
9 10 11 12
a) To avoid electrical shock, connect power at last;
Out1 Out2
Over-range
The sensor break will be signalled as an out of range:
2
3
SEnS
dP
TC, Pt100 input
J, crAL, S, r, t, ir.J, ir.cA, Pt1, 0... 50 (mV),
0... 60 (mV), 12... 60 (mV)
J
TC, PTC, NTC input
J, crAL, S, r, t, Ir.J, Ir.cA, Ptc, ntc, 0... 50 (mV),
0... 60 (mV), 12... 60 (mV)
Ptc
Current input
0... 20 (mA), 4... 20 (mA)
4.20
Voltage input
0... 5(V), 1... 5(V), 0... 10(V), 2... 10(V), 0... 1 (V)
0.10
Decimal figures
0... 3
0
A-5
A-4
4
SSc
Initial scale readout
From -1999 to FSC (E.U.)
-1999
A-6
5
FSc
Final scale readout
From SSc to 9999 (E.U.)
9999
A-7
6
0.Pot
Offset value (to shift the
zero readout)
From SSc to Fsc (E.U.)
0 = °C
7
unit
Engineering unit
°C or °F
0 = °C
A-8
FiL
Digital filter on the
measured value
From 0 (oFF) 20.0 (s)
1.0
C-0
8
9
diF1
Digital input 1 function
10
diF2
Digital input 2 function
oFF
AAC
ASi
HoLd
r.Pic
0.Pot
r.PoP
t.rHr
t.run
t.rES
t.rH
uP.du
= No function
= Alarm Reset
nonE
= Alarm acknowledge (ACK)
= Hold of the measured value
= Peaks reset
= Start of the 0.Pot procedure
= Start of the 0.Pot proc. and Peaks reset
= Timer Run/Hold/Reset [transition]
= Timer Run [transition]
nonE
= Timer reset [transition]
= Timer run/hold [Status]
= Digital inputs in parallel to
and
keys
A-13
A-14
]
]
Out Group (parameters relative to the outputs)
no. Parameter
11
o1F
Description
Out 1 function
Range
nonE
AL
t.out
t.HoF
or.bo
P.FAL
bo.PF
diF.1
diF.2
12
13
o1AL
o1Ac
= Output not used.
= Alarm output
= Timer output
= Tiemer out - OFF in Hold
= Out-of-range or burn out indicator
= Power failure indicator
= Out-of-range, burn out and Power failure
indicator
= The output repeats the digital input 1 status
= The output repeats the digital input 2 status
Vis.
Default
Promo.
H.reg
Alarms linked to output 1
0... 15
+1
= Alarm 1
+2
= Alarm 2
+4
= Alarm 3
+8
= Alarm 4
+16
= Sensor break (burn out)
AL1
Out 1 action
dir
rEU
dir.r
ReU.r
dir
= Direct action
= Reverse action
= Direct with reversed LED
= Reverse with reversed LED
A-17
C-0
o2F
Out 2 function
AL 1
A-19
o2AL
Alarms linked up with out 2 Same range as [12] o1AL - Alarms linked to output 1
AL1
A-20
16
o2Ac
Out 2 action
Same range as [13] o1Ac - Out 1 action
dir
C-0
17
o3F
Out 3 function
Same range as [11] o1F - Out 1 function
AL
A-22
18
o3AL
Alarms linked up with out 3 Same range as [12] o1AL - Alarms linked to output 1
AL2
A-23
19
o3Ac
Out 3 action
Same range as [13] o1Ac - Out 1 action
dir
C-0
20
o4F
Out 4 function
Same range as [11] o1F - Out 1 function
AL
A-24
21
o4AL
Alarms linked up with out 4 See parameter [12] o1AL - Alarms linked to output 1
AL2
A-25
22
o4Ac
Out 4 action
dir
C-0
]
AL1 Group (parameters relative to AL1 - alarm 1)
no. Parameter
23
24
AL1t
Ab1
Description
Range
Alarm 1 type
nonE
LoAb
HiAb
LHAb
SE.br
= Alarm not used
= Absolute low alarm
= Absolute high alarm
= Absolute band alarm
= Sensor break
Alarm 1 function
From 0 to 15
+1
= Not active at power up
+2
= Latched alarm (manual reset)
+4
= Acknowledgeable alarm
LoAb
Same range as [24] AB1 - Alarm 1 function
0
C-0
49
AL4L
- For High and low alarms, it is the low limit
Same range as [25] AL1L - Low limit of the
of the AL4 threshold
AL1 threshold/How AL1 threshold
- For band alarm, it is low alarm threshold
-1999
C-0
50
AL4H
- For High and low alarms, it is the high
Same range as [26] AL1L - High limit of the
limit of the AL4 threshold
AL1 threshold/High AL1 threshold
- For band alarm, it is high alarm threshold
9999
C-0
51
AL4
AL4 threshold
From AL4L to AL4H (E.U.)
0
C-0
52
HAL4
AL4 hysteresis
From 1... 9999 (E.U.)
1
C-0
53
AL4d
AL4 delay
From 0 (oFF) to 9999 (s)
oFF
C-0
Alarm 4 at out of range indication
No = Alarm NOT running when out-of-range
no
YES = Alarm enabled when out-of-range
C-0
54
AL4o
Tin Group
no. Parameter
26
AL1H
- For High and low alarms, it is the high
limit of the AL1 threshold
From AL1L to 9999 ( E.U.)
- For band alarm, it is high alarm threshold
9999
A-49
27
AL1
AL1 threshold
From AL1L to AL1H (E.U.)
0
A-50
28
HAL1
AL1 hysteresis
1... 9999 (E.U.)
1
A-51
29
AL1d
AL1 delay
From 0 (oFF) to 9999 (s)
oFF
C-0
Alarm 1 at out of range indication
No = Alarm NOT running when out-of-range
no
YES = Alarm enabled when out-of-range
C-0
tr.F
Independent timer function
56
tr.u
Timer unit
hh.nn = Hours and minutes
nn.SS = Minutes and seconds
SSS.d = Second and tenth of seconds
57
tr.t1
Time 1
58
tr.t2
Time 2
tr.St
Timer status
Description
Range
Description
C-0
uSrb
=
=
=
=
=
=
=
=
=
=
No function
Alarm reset
Alarm acknowledge
Hold of the measured value
The display will shows the peaks
Peaks reset
Start the 0.Pot routine
0.Pot routine + Peaks reset
Input calibration with self-learning procedure
Timer run/hold/reset
nonE
A-94
63
diSP
Display management
nonE
AL1
AL2
AL3
ti.uP
ti.du
=
=
=
=
=
=
Standard display
Alarm 1 threshold
Alarm 2 threshold
Alarm 3 threshold
Timer time up
Timer time down
nonE
A-95
64
Edit
Alarm editing enable
AE
AnE
= Alarm thresholds can be modified
= Alarm threshold can NOT be modified
??
??
]
AL2L
-1999
A-56
no. Parameter
34
AL2H
- For High and low alarms, it is the high
Same range as [26] AL1L - High limit of the
limit of the AL2 threshold
AL1 threshold/High AL1 threshold
- For band alarm, it is high alarm threshold
9999
A-57
35
AL2
AL2 threshold
From AL2L to AL2H (E.U.)
0
A-58
36
HAL2
AL2 hysteresis
1.... 9999 (E.U.)
1
A-59
37
AL2d
AL2 delay
From 0 (oFF) to 9999 (s)
oFF
C-0
Alarm 2 at out of range indication
No = Alarm NOT running when out-of-range
YES = Alarm enabled when out-of-range
no
C-0
65 Add
Address
66 bAud
Baud rate
]
C-0
]CAL Group (User calibration)
AL2L
-1999
C-0
no. Parameter
AL2H
- For High and low alarms, it is the high
Same range as [26] AL1L - High limit of the
limit of the AL3 threshold
AL1 threshold/High AL1 threshold
- For band alarm, it is high alarm threshold
9999
AL3 threshold
From AL3L to AL3H (E.U.)
0
HAL2
AL3 hysteresis
From 1... 9999 (E.U.)
1
C-0
AL2d
AL3 delay
From 0 (oFF) to 9999 (s)
oFF
C-0
46
AL2o
Alarm 3 at out of range indication
No = Alarm NOT running when out-of-range
YES = Alarm enabled when out-of-range
no
C-0
= Not used
= Total worked days
= Total worked hours
Threshold of the worked hours/days From 0 (oFF) to 9999 (days/hours)
0
45
oFF
dAY
Hour
68 h.Job
Same range as [24] AB1 - Alarm 1 function
44
Vis.
Promo.
C-0
C-0
Vis.
Default Promo.
Range
Measurement type
Alarm 3 function
C-0
9600
67 co.ty
- For High and low alarms, it is the low limit
Same range as [25] AL1L - Low limit of the
of the AL3 threshold
AL1 threshold/How AL1 threshold
- For band alarm, it is low alarm threshold
AL2
1
Description
Ab3
43
Default
CON Group (worked time count)
no. Parameter
C-0
Range
0 (oFF)... 254
1200 (bit/s)
2400 (bit/s)
9600 (bit/s)
19.2 (kbit/s)
38.4 (kbit/s)
Same range as [23] AL1t - Alarm 1 type
40
42
Description
Alarm 3 type
AL3t
41
SER Group
Vis.
Default Promo.
C-0
LoAb
39
Vis.
Default Promo.
Range
nonE
AAc
ASi
HoLd
button function during d.Pic
r.Pic
run time
0.Pot
r.Pot
t.Pot
Str.t
C-0
Range
C-0
A-93
0
Description
rES
30
Same range as [24] AB1 - Alarm 1 function
no. Parameter
A-65
3... 999
Alarm 2 function
AL3 Group (parameters relative to AL3 - alarm 3)
1.00
From 0 (oFF) to 999 (oFF = Level 2 not protected by psw) 20
- For High and low alarms, it is the low limit
Same range as [25] AL1L - Low limit of the
of the AL2 threshold
AL1 threshold/How AL1threshold
- For band alarm, it is low alarm threshold
AL2o
A-64
Password level 3
Ab2
38
1.00
Password level 2
A-54
33
A-63
PAS3
LoAb
32
nn.SS
PAS2
Same range as [23] AL1t - Alarm 1 type
AL2t
00.01... 99.59 when tr.u = hh.nn
00.01... 99.59 when tr.u = nn.SS
000.1... 995.9 when tr.u = SSS.d
00.01... 99.59 when tr.u = hh.nn + iNF
00.01... 99.59 when tr.u = nn.SS + iNF
000.1... 995.9 when tr.u = SSS.d + iNF
run
= timer run
HoLd = timer hold
rES = timer reset
A-62
61
Alarm 2 type
31
= Timer not used
= Delayed start timer
= Delayed start at power up
nonE
= Feed-through timer
= Asymmetrical oscillator with start in OFF
= Asymmetrical oscillator with start in ON
Vis.
Promo.
60
62
Vis.
Default Promo.
Default
PAN Group
AL2 Group (parameters relative to AL2 - alarm 2)
no. Parameter
Range
55
no. Parameter
A-48
]
Description
NonE
i.d.A
i.uP.d
i.d.d
i.P.L
i.L.P
]
-1999
]
Same range as [23] AL1t - Alarm 1 type
Alarm 4 function
A-47
- For High and low alarms, it is the low limit
of the AL1 threshold
From -1999 to AL1H ( E.U.)
- For band alarm, it is low alarm threshold
AL1o
Alarm 4 type
LoAb
AL1L
Vis.
Promo.
C-0
Ab4
59
C-0
Default
AL4t
Vis.
Promo.
0
Range
48
Default
25
30
Description
47
]
15
Same range as [13] o1Ac - Out 1 action
no. Parameter
A-16
14
Same range as [11] o1F - Out 1 function
AL4 Group (parameters relative to AL4 - alarm 4)
Description
Range
nonE
A-97
oFF
A-100
Vis.
Default Promo.
69
A.L.P
Adjust low Point
From -1999 to AH.P-10 (E.U.)
0
A-9
70
A.L.o
Adjust low Offset
-300... +300 (E.U.)
0
A-10
71
A.H.P
Adjust High Point
From A.L.P +10 to 9999 (E.U.)
9999
A-11
72
A.H.o
Adjust High Offset
-300... +300 (E.U.)
0
A-12
">