ECHO GT-2000R Type 1E Grass Trimmer Manuel d'utilisation

PDF

Dokumen

Grass Trimmer

Operator's Manual

MODEL GT-2000R Type 1E

Serial Number 001001 & Up

X7702275801

WARNING DANGER

Read rules for safe operation and instructions carefully. ECHO provides an

Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.

X770000541

11/01

NTRODUCTION

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-thejob-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages.

THE OPERATOR

S MANUAL

Read and understand this manual before operation. Keep it in a safe place for future reference. It contains specifications and information for operation, starting, stopping, maintenance, storage and assembly specific to this product.

THE SAFETY MANUAL

Read and understand this manual before operation. Keep it in a safe place for future reference. It explains possible hazards involved with the use of Grass Trimmers and Brush cutters and what measures you should take to make their use safer.

ABLE OF

ONTENTS

Introduction ............................................................... 2

- The Operator's Manual ....................................... 2

- The Safety Manual ............................................. 2

Manual Safety Symbols and Important Information .. 3

Safety ......................................................................... 3

- Decals ................................................................. 3

- International Symbols ......................................... 4

Safety Instructions .................................................... 4

- Personal Conditions and Safety Equipment ....... 4

- Extended Operation/Extreme Conditions ............ 5

- Equipment ........................................................... 5

- Safe Operation .................................................... 6

Emission Control ........................................................ 6

Description ................................................................ 6

- Contents List ...................................................... 7

Specifications ............................................................. 9

Assembly ................................................................. 10

- Plastic Shield Installation .................................. 10

- Nylon Head Installation .................................... 10

- Nylon Line Installation ..................................... 11

- Front (Loop) Handle ......................................... 11

Pre-Operation ........................................................... 12

- Fuel ................................................................... 12

Operation ................................................................. 13

- Starting Cold Engine ......................................... 13

- Starting Warm Engine ....................................... 14

- Stopping Engine ............................................... 14

Maintenance ............................................................ 15

- Skill Level .......................................................... 15

- Maintenance Intervals ...................................... 15

- Air Filter ............................................................ 16

- Fuel Filter .......................................................... 16

- Spark plug ......................................................... 17

- Cooling System ................................................. 17

- Exhaust System ................................................. 18

- Carburetor Adjustment ..................................... 19

- Lubrication ........................................................ 20

Troubleshooting ...................................................... 21

Storage ..................................................................... 22

Servicing Information ............................................... 24

- Parts .................................................................. 24

- Service .............................................................. 24

- ECHO Consumer Product Support .................... 24

- Warranty Card .................................................. 24

- Additional or Replacement Manuals ................ 24

Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.

RASS

RIMMER

PERATOR

ANUAL

ANUAL

AFETY

YMBOLS AND

MPORTANT

NFORMATION

Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders.

IMPORTANT The enclosed message provides information necessary for the protection of the unit.

The circle with the slash symbol means whatever is shown within the circle is prohibited.

NOTE This enclosed message provides tips for use, care and maintenance of the unit.

AFETY

DECALS

Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.

A. SHAFT DECAL

WARNING DANGER

•This unit can be dangerous and cause serious injury if improperly used. • Operators, helpers and bystanders can be severely in jured by thrown objects and must wear specified ANSI Z87.1 eye protection. Blindness or loss of eye can occur. Do not rely on cutter head shield to protect eyes. Ricochet can occur. •to avoid accidental contact, keep everyone beyond operating area. •To reduce the risk of injury to operator, helpers & bystanders, read and understand your operator's and safety manuals. For a free copy of the safety

Manual, write to ECHO, INCORPORATED, 400 Oakwood Road, Lake Zurich, IL 60047. •Keep shield and other components in place and in good condition. Do not use attachments or other parts not approved by ECHO. GT style (non-blade capable) units must not be converted to blade use except Maxi-Cuts or similar ECHO approved attachments.

B. SPANISH DECAL

C. SHIELD DECAL

890228-09560

ADVERTENCIA PELIGRO

Esta unidad puede ser peligrosa y producir lesiones personales graves si no se usa en forma adecuada. Para reducir el riesgo de lesionarse, los operadores, los ayudantes y los espectadores deben leer y comprender el

Manual Del Operador y los Manuales De

Seguridad que se entregan escritos en español.

ENGLISH TRANSLATION

WARNING DANGER

This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety

Manuals, which are provided in Spanish.

INTERNATIONAL SYMBOLS

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

Read and understand

Operator's Manual.

FUEL AND OIL

MIXTURE

WEAR EYES, EARS

AND HEAD

PROTECTION

HOT

SURFACE

FINGER SEVERING

WEAR SLIP

RESISTANT

FOOT WEAR.

DO NOT SMOKE

NEAR FUEL.

WEAR HAND AND

FOOT PROTECTION

SAFETY/ALERT

KEEP BYSTANDERS AND HELPERS

AWAY 15 M (50 FT.).

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

DO NOT ALLOW

FLAMES OR

SPARKS NEAR

FUEL.

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

EMERGENCY STOP

Engine choke control.

IGNITION

ON/OFF

PRIMER

BULB

DO NOT EXCEED

10,000 RPM.

CARBURETOR

ADJUSTMENT

- HIGH SPEED

MIXTURE

CARBURETOR

ADJUSTMENT

- LOW SPEED

MIXTURE

DO NOT OPERATE

WITHOUT

GUARDS AND

SHIELDS IN

PLACE.

DO NOT USE

BLADES. STRING

LINE ONLY

CARBURETOR

ADJUSTMENT

- IDLE SPEED

BEWARE

- THROWN,

RICOCHET

OBJECTS

AFETY

NSTRUCTIONS

PERSONAL CONDITION AND SAFETY EQUIPMENT

WARNING DANGER

Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the trimmer.

Hand Protection

Wear no-slip, heavy duty work gloves to improve your grip on the Trimmer/Brush Cutter handles. Gloves also reduce the transmission of machine vibration to your hands.

Hearing Protection

ECHO recommends wearing hearing protection whenever unit is used.

Proper Clothing

Wear snug fitting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARVES, JEWELRY.

Wear sturdy work shoes with non-skid soles;

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

RASS

RIMMER

PERATOR

ANUAL

EXTENDED OPERATION

/

EXTREME CONDITIONS

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended, because the minimum exposure which might trigger the ailment is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands, and wrists.

• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.

• If you experience discomfort, redness and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress

Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome

(CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

EQUIPMENT

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive movement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness, or pain in the fingers, hands, wrists, or arms. The sooner RSI/

CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented.

WARNING DANGER

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments, or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety manual.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks.

DO NOT operate unit if leaks are found.

• Inspect shield for damage and ensure that the cut-off knife issecurely in place. Replace if either is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that front (loop) handle and optional shoulder/waist harness are adjusted for safe, comfortable operation. See Assembly for proper adjustment.

• Have repairs done only by an authorized ECHO Service Dealer.

• Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation.

SAFE OPERATION

WARNING DANGER

Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.

• Provide all operators of this equipment with the Operator's Manual and instructions for safe operation.

Keep A Firm Grip

• Hold the front and rear handles with both hands with thumbs and fingers encircling the handles

Keep A Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach.

MISSION

ONTROL

The emission control system for these engines is EM (Engine Modification).

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY : TEH021UB24RA

DISPLACEMENT : 21.2cc

THIS ENGINE MEETS U.S. EPA PHI AND 1995 -

1999 CALIFORNIA EMISSION REGULATIONS

FOR ULGE ENGINES. REFER TO OWNER’S

MANUAL FOR MAINTENANCE SPECIFICA-

TIONS AND ADJUSTMENTS.

An Emission Control Label is located on the engine. (This is an

EXAMPLE ONLY, information on label varies by engine FAMILY).

ESCRIPTION

The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and positioning of the front handle are necessary.

After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.

RASS

RIMMER

PERATOR

ANUAL

CONTENT LIST

____ 1 - Trimmer Assembly

____ - Power Head

____ - Drive Shaft Assembly

____ 1 - Plastic Bag (Co-Pack)

____ - Rapid Loader TM 2-line Head

____ - Operator's Manual

____ - Safety Manual

____ - Shield Assembly

____ - Shield Mount Hardware

____ -1, 1/4-20 bolt

____ -1, 1/4-20 wing nut

____ -1, 1/4-20 flat washer

____ - Line Head Mount Hardware

____ -1, 3/8-24 Locknut

____ -1, Small Washer

____ -1, Large Washer

____ -12, 8 in. X .080 Pre-cut Nylon Line

____ - Locking Tool

____ - Warranty Card & Limited Warranty

____ - Safety Glasses

____ - Oil 2 Stroke

Safety

Video

1. POWER HEAD - Factory Assembled to the Driveshaft assembly. Includes the Engine, Clutch, Fuel System, Ignition

System and Recoil Starter.

2. GRIP - Rear (right hand) handle.

3. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be repositioned for proper cutting attitude and operator comfort.

4. DRIVESHAFT ASSEMBLY - Factory Assembled to the Power Head. Includes the Rear (right hand) Handle

Assembly, Bearing Housing Assembly, Throttle Trigger, Front (loop, left hand) Handle Assembly, Flexible Drive

Cable and Safety Decals.

5. RAPID LOADER TM HEAD - Contains replaceable nylon trimming lines.

6. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming operation.

7. CUT-OFF KNIFE - Trims line to the correct length.

8. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique.

9. STOP SWITCH - "TOGGLE SWITCH" mounted on the engine. Move switch UP to RUN, DOWN to STOP.

10. ARM REST - Provides arm rest during operation and protects arm from hot engine.

11. MUFFLER SPARK ARRESTOR - The muffler controls the exhaust noise while the spark arrestor prevents hot particles of carbon from leaving leaving the muffler where they could possibly start a fire.

12. FUEL TANK - Contains fuel and fuel filter.

13. RECOIL STARTER HANDLE - Pull handle slowly until recoil starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.

14. FUEL TANK CAP - Cover and seals fuel tank opening.

15. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.

16. AIR CLEANER - Contains replaceable filter element.

17. CHOKE - Located above the air cleaner housing. Controls operation of choke. Move choke to starting position

(Close Choke) and back to run position (Open Choke).

18. SPARK PLUG - Provides spark to ignite fuel mixture.

19. SAFETY VIDEO - (Not included with unit) P/N 99922202540 English version only is available at a cost of $5.00 from

ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information on safe operation.

RASS

RIMMER

PERATOR

ANUAL

PECIFICATIONS

M O D E L

L e n g t h

W i d t h

H e i g h t

W e i g h t ( d r y ) w / C u t t e r H e a d

E n g i n e T y p e

B o r e

S t r o k e

D i s p l a c e m e n t

E x h a u s t S y s t e m

C a r b u r e t o r

I g n i t i o n S y s t e m

S p a r k P l u g

F u e l

F u e l / O i l R a t i o

G a s o l i n e

O i l

F u e l T a n k C a p a c i t y

S t a r t e r S y s t e m

C l u t c h

D r i v e S h a f t

R o t a t i n g D i r e c t i o n

C u t t e r H e a d

H a n d l e

S h o u l d e r H a r n e s s

I d l e S p e e d ( R P M )

W i d w i t h e

O p e n y l o n L i

T h n e r o t t l e S p e e d

H e a d ( R P M

( W .

O .

T .

)

G T 2 0 0 0 R

1 4 0 0 m m ( 5 5 .

1 i n .

)

3 3 0 m m ( 1 3 .

0 i n .

)

3 6 0 m m ( 1 4 .

2 i n .

)

4 .

0 8 k g ( 9 .

0 l b .

)

A i r c o o l e d , t w o s t r o k e , s i n g l e c y l i n d e r g a s o l i n e e n g i n e

3 2 .

2 m m ( 1 .

2 6 8 i n .

)

2 6 .

0 m m ( 1 .

0 4 i n .

)

2 1 .

2 c c ( 1 .

2 9 c u .

i n .

)

S p a r k A r r e s t o r M u f f l e r

Z a m a d i a p h r a g m m o d e l C 1 U w / p r i m e r

F l y w h e e l m a g n e t o , c a p a c i t o r d i s c h a r g e

N G K B P M 7 A G a p 0 .

6 5 m m ( 0 .

0 2 6 i n .

)

M i x e d ( G a s o l i n e a n d T w o s t r o k e O i l )

5 0 : 1 E C H O H i g h P e r f o r m a n c e , t w o s t r o k e a i r c o o l e d e n g i n e o i l

8 9 O c t a n e u n l e a d e d .

D O t h a n 1 0 %

N O T e t h y l u s e f u e l a l c o h o l c o n t a i n i n g o r 1 5 % m e t

M T B E .

h y l a l c o h o l , m o r e

5 0 : 1 E C H O H i g h P e r f o r m a n c e , t w o s t r o k e a i r c o o l e d e n g i n e o i l

0 .

4 l i t .

( 1 3 .

5 U S f l .

o z .

)

A u t o m a t i c R e w i n d S t a r t e r

C e n t r i f u g a l T y p e

1 / 4 " F l e x S h a f t

C l o c k w i s e v i e w e d f r o m t o p

N y l o n l i n e h e a d ( 2 l i n e ) w i t h .

0 8 0 L i n e c a p a c i t y 2 0 3 m m ( 8 i n .

)

L e f t D L o o p , R i g h t G r i p

O p t i o n a l P / N 9 9 9 4 4 2 0 0 2 0 1

2 4 0 0 3 2 0 0 R P M

6 8 0 0 7 5 0 0 R P M

SSEMBLY

Tools Required: None

PLASTIC SHIELD

1. Snap the shield over the bearing housing.

2. Install bolt (A), washer (B) and wing nut (C).

NYLON LINE HEAD

Tools Required: Head Locking Tool

Parts Required: Rapid Loader TM Head.

1. Remove plastic threaded shaft sleeve and adapter plate from PTO shaft.

2. Align locating hole in upper plate with hole in bearing housing and insert 1/8 in. diameter locking tool (A).

3. Place large washer then line head on threaded shaft followed by small metal washer and locknut.

4. Tighten locknut securely.

IMPORTANT

Remember to remove the locking tool.

NYLON LINE INSTALLATION

Level 1.

Tools Required: None

Parts Required: Two (2) Pre-cut Nylon Line 8 in. X .080 in.

1. Shut engine off. Lay unit on the ground with head assembly up.

2. Remove old nylon line through center recess of head.

3. Thread new lines through outside holes (A) in housing until ends meet in center of recess.

NOTE

Insert cutting line ends to center of head recess to insure easy removal of used lines.

RASS

RIMMER

PERATOR

ANUAL

FRONT

(

LOOP

)

HANDLE

NOTE

Front handle is pre-installed. Re-positioning and tightening is all that is required.

1. Position front handle (E) in comfortable operating position and tighten wing nut (F). The cutting attachment should be 5-7.5 cm

(2-3 in.) above the ground and as level as possible.

RE

- O

PERATION

FUEL

Fuel Requirements

Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline known

2 to be good quality. Gasoline may contain up to 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD Standard

(ISO/CD 13738), must be used. Echo brand Premium 50:1 oil meets this standard. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD approved oil, such as Echo Premium 50:1

Two-stroke Oil, will void the two-stroke engine warranty. (Emission related parts only are covered for two years, regardless of two-stroke oil used, per the statement listed in the EPA Phase I/California Emission

Defect Warranty Explanation.)

IMPORTANT

Echo Premium 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals.

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of gasoline.

2. Add 2-stroke oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline and remix.

5. Install fuel container cap and wipe any spilled fuel from container and surrounding area.

Handling Fuel

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information.

After refueling;

• Wipe any spilled fuel from the unit.

• Move at least 3 m (10 ft.) from refueling location before starting the engine.

After use;

• DO NOT store a unit with fuel in its tank.

Leaks can occur. Return unused fuel to an approved fuel storage container.

Storage -

Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, air tight container. Store in a well ventilated, unoccupied building, away from sparks and flames. Do not store fuel longer than 30 days.

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate.

ALWAYS shake fuel container thoroughly before each use.

WARNING DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow flames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT!

• NEVER refuel a unit with the engine running.

• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

• Securely tighten fuel cap after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

RASS

RIMMER

PERATOR

ANUAL

PERATION

STARTING COLD ENGINE

WARNING DANGER

The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result.

NOTE

Refer to the Grass Trimmer / Brush Cutter Safety Manual for proper and safe trimming techniques.

1. Stop Switch

Move stop switch button (A) away from the STOP position.

2. Choke

Move choke (B) to “Cold Start” Position.

3. Primer

Pump primer bulb (C) until fuel will be visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.

WARNING DANGER

Inspect starting area for hazards such as rocks, glass, debris etc.

which could be thrown by the cutting attachment when starting.

Keep helpers and bystanders at least 15m (50 feet) from starting area, otherwise serious personal injury may result.

4. Recoil Starter

Lay the trimmer on a flat clear area. Firmly grasp throttle grip with left hand and fully depress throttle trigger to wide open position.

Rapidly pull recoil starter handle/rope (D) until engine fires

(maximum five [5] pulls).

5. After engine fires or five (5) pulls, move choke lever back to “Run” position. Hold throttle trigger fully depressed and pull starter handle/rope until engine starts and runs. Release throttle trigger and allow unit to warm up at idle for several minutes.

NOTE

If engine does not start with choke in “Run” position after 5 pulls, repeat instructions.

6. After engine warm up, gradually depress throttle trigger to increase engine RPM to operating speed.

STARTING WARM ENGINE

WARNING DANGER

1. Stop Switch

Move stop switch button (A) away from the STOP position.

2. Recoil Starter

Lay the trimmer on a flat clear area and pull the recoil starter handle

(D) until the engine fires.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

STOPPING ENGINE

1. Throttle

Release throttle and allow engine to return to idle before shutting off engine.

2. Stop Switch

Move stop switch button (A) backward to STOP position.

WARNING DANGER

If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine.

Have your ECHO dealer repair stop switch before using trimmer again.

RASS

RIMMER

PERATOR

ANUAL

AINTENANCE

Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the

ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your Echo dealer for repairs.

SKILL LEVEL

Level 1 = Easy to do. Most required tools come with unit.

Level 2 = Moderate difficulty. Some specialized tools may be required.

Level 3 = Experience required. Specialized tools are required. ECHO recommends that the unit be returned to your ECHO dealer for servicing.

ECHO offers REPOWER TM Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.

MAINTENANCE INTERVALS

C o m p o n e n t / S y s t e m M a i n t e n a n c e P r o c e d u r e

D a i l y o r

B e f o r e

U s e

E v e r y

R e f u e l

3 M o n t h s o r 9 0

H o u r s

6 M o n t h s o r 2 7 0

H o u r s

Y e a r l y

A i r F i l t e r

F u e l S t r a i n e r

I n s p e c t / R e p l a c e

I / C R *

I R

F u e l L i n e I n s p e c t / R e p l a c e I I

C a r b u r e t o r I n s p e c t / C l e a n / R e p l a c e I / C

C h o k e S y s t e m I n s p e c t / C l e a n / R e p l a c e I / C

C o o l i n g S y s t e m I n s p e c t / C l e a n I / C

M u f f l e r S p a r k

A r r e s t o r

D r i v e

C a b l e

S h a f t ( F l e x

M o d e l s )

S t a r t e r R o p e

I n s p e c t / C l e a n

G r e a s e

(

2 )

F u e l L e a k s

I n s p e c t / C l e a n

I n s p e c t / R e p a i r

I I

S p a r k P l u g C l e a n / R e p l a c e I / C R *

S c r e w s / N u t s / B o l t s I n s p e c t / T i g h t e n / R e p l a c e I

I = I n s p e c t / R

I M P O R T A N T

T i m e i n t e r v a m a i n t e n a n c e .

l s

= R e p l a c e s h o w n a r e m

/ a x

C = C l i m u m .

e a

A c t n u a l u s e a n d y o u r e x p e r i e n c e w i l l d e t e r m i n e t h e f r e q u e n c y

( 1 ) R e p l a c e m e n t w i l l b e r e q u i r e d f o r c o m m e r c i a l u r e q u i r e d .

C l e a n i n g i n c l u d e s R e b u i l d

(

2 )

A l l

A p r e p l y c o

E C H O m m e n d a

® t i o

U n s

B E T M t o r e e p v l a e r y c e

2 5 a r e

K i t s .

h o u r s b a s e d o f o n u s e .

t h e s e f i n y e a r d i n g l y .

o f

F o r C o n s d a m a g e u m e r o r w e a u s e , r d u c l e a r i n g n i n g i n s p e e v e r y c t i o n .

6 o f r e q u m o n t h s i i r e d s

AIR FILTER

Level 1.

Tools required: Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle paint brush.

Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT.

Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area.

Remove the air cleaner cover. Clean and inspect the element for damage. If element is fuel soaked and very dirty, replace.

If element can be cleaned and reused, be certain it:

• still fits the cavity in the air cleaner cover.

• is installed with the original side out.

NOTE

Carburetor adjustment may be needed after air filter cleaning/ replacement. See Carburetor Adjustment Section.

FUEL FILTER

Level 1.

Tools required: Fuel line hook, 200-250 mm (8-10 in.) length of wire with one end bent into a hook. Clean rag, funnel, and an approved fuel container.

Parts required: 90008 REPOWER TM AIR & FUEL FILTER KIT

WARNING DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or handling.

Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank.

Use the “fuel line hook” to pull the fuel line and filter from the tank.

Remove the filter from the line and install the new filter.

SPARK PLUG

Level 2.

Tools Required: Spark Plug socket wrench and screw driver, Feeler gauge, preferably a wire gauge.

Parts Required: 90064 REPOWER TM TUNE-UP KIT

Remove spark plug and check for fouling, worn and rounded center electrode.

Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine.

Adjust spark plug gap by bending outer electrode.

Tighten spark plug to 145-155 kg/cm (125-135 in. lb.).

COOLING SYSTEMS CLEANING

Level 2.

Tools required: Cross Head Screwdriver, 3 mm Hexagon wrench,

Pointed Wood Stick, Cleaning Brush, 25-50 mm

(1-2 in.) medium bristle paint brush.

Parts Required: None.

IMPORTANT

To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the cylinder.

• Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance”. Any failure attributed to lack of maintenance is not warranted.

Remove spark plug lead and throttle linkage end from the carburetor swivel.

Remove the four screws that retain the cover. Two at the top of the

Recoil Starter, two on either side of the front. Lift the cover from the engine and lay to the front of the trimmer.

NOTE

The throttle linkage remains assembled to the cover and the spark plug lead and grommet remain installed.

RASS

RIMMER

PERATOR

ANUAL

0.65 mm

(0.026 in.)

IMPORTANT

DO NOT use a metal scraper to remove dirt from the cylinder fins.

Use the wooden stick or brush to remove dirt from the cylinder fins.

Remove grass and leaves from the grid between the starter and fuel tank.

When installing the cover, be certain the tab of the metal deflector shield is in the slot of the cover.

EXHAUST SYSTEM

Spark Arrestor Screen

Level 2.

Tools Required: Cross Head Screwdriver. Soft metal brush.

Parts Required: Screen P/N 14586240630, Gasket Lid P/N 14586642031

WARNING DANGER

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.

Remove spark arrestor screen cover (A), screen holder (B), gasket

Clean carbon deposits from screen (D) and muffler components.

Replace screen if it is cracked, plugged or has holes burned through.

Assemble components in reverse order.

CARBURETOR ADJUSTMENT

Level 2.

Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017).

Parts required: None.

NOTE

Every unit is run at the factory and the carburetor is set in compliance with EPA Phase 1 and California Emission Regulations. In addition, the carburetor is equipped with HI and LO needle adjustment limiters that prevent settings outside acceptable limits.

Before adjusting the carburetor, clean or replace the air filter and spark arrester screen.

The trimmer line should be new.

Start engine and run for several minutes to reach operating temperature.

Stop engine. Turn HI speed needle (A) CCW (counter clockwise) to stop. Turn LO speed needle (B) midway between full CCW and CW

(clockwise) stops.

Idle Speed Adjustment.

• Start engine and turn “idle” speed adjustment screw (C) CW until the blades begin to turn, then turn the screw CCW until blades stop turning. Turn screw CCW an additional 1/4 turn.

Accelerate to full throttle for 2-3 seconds to clear excess fuel from engine then return to idle. Accelerate to full throttle to check for smooth transition from idle to full throttle. If engine hesitates, turn

LO needle (B) CCW an additional 1/8 turn and repeat acceleration.

Continue adjusting until smooth acceleration results.

Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed

RPM should be set to specifications found on page 9 "Specifications" of this manual.

Check idle speed and reset if necessary. If a tachometer is available, idle speed should be set to the specification found on page 9

"Specifications" of this manual.

WARNING DANGER

When carburetor adjustment is completed, the cutting attachment should not turn at idle, otherwise serious personal injury may result.

RASS

RIMMER

PERATOR

ANUAL

LUBRICATION

Level 1.

Tools Required: 8mm Open End Wrench, Screwdriver, Clean Rag.

Parts Required: ECHO

Grease.

LUBE TM 8 oz. (P/N 91014) or Lithium Base

1. Remove plastic shield.

2. Loosen bearing housing locating screw (A), at the top of the housing, remove mounting screw (B).

3. Pull the flexible drive shaft (C) from the housing, wipe clean and recoat with a thin coating [1/2 oz. (15 ml)] of grease.

4. Slide the flexible drive shaft back in the drive housing being careful not to get dirt on the flexible drive shaft.

5. Install the bearing housing and shield.

RASS

RIMMER

PERATOR

ANUAL

ROUBLESHOOTING

P r o b l e m

E n g i n e s t c r a r a n t s k s h a r d / d o e s n t' s t a r t

E N G I N E P R O B L E M T R O U B L E S H O O T I N G C H A R T

C h e c k

F u e l a t c a r b u r e t o r

S t a t u s C a u s e

N o f u e l a t c a r b u r e t o r F u e l

F u e l s t r a il n e i n e r c l o g g e d c l o g g e d

C a r b u r e t o r

F u e l a k t

S p a r k

S o f p a p

A i r l r u c g if a a y tl t t il n e w i r e p l e r d n e d u g r

M o u f

A f lf i u e r

N r e l w o o if a tl s s t e t p p e r c a a y w r r d i k k il t i r n d h t y f e r u e l

S t a

F u

E l e c t r i c a l

I n t e r l o c k

N o r e l b o p u s r

M i e w t i t o c r x t u r e h o t o o f f s w i t c h r i p r o b l e m c h

S p a r k g a p i n c o r r e c t

C o v e r e d

F o u l e d w i w i t h t h c f u e l a r b o n

P l u g d e f e c it v e r m a l w e a r

R e m e d y

C l e a n o r r e p l a c e

S e e y o u r E c h o d e a l e r

O p e n c h o k e

C l e a n / r e p l a c e

A d j u s t a i c a r b u r e t o r r

S e e y o u r if tl e r

E c h o d e a l e r

T u r n

S e e s w y o u i t r c h t o

E c h o

O N d e a l e r

S e e y o u r E c h o d e a l e r

A d j u s t t o .

6 5 m m

C l e a n

C l e a n o r o r r e p l a c e r e p l a c e

( 0 .

0 2 6 i n .

)

R e p l a c e p l u g

C l e a n o r r e p l a c e

F u e l if tl e r

E n g i n e r u n s , b u t d i e s o r d o e s n o t a c c e l e r a t e p r o p e r l y

F u e l v e n t

S p a r k P l u g

C a r b u r e t o r

C o o il n g S y s t e m

F u e l if tl e r d i r t y

F u e l v e n t p l u g g e d

P l u g d i r t y / w o r n

C o n t a m i n a n t s / r e s i d u e s f u e l i n R e p l a c e

C l e a n o r r e p l a c e C o n t a m i n a n t s / r e s i d u e s f u e l i n

N o r m a l w e a r C l e a n a n d a d j u s t o r r e p l a c e

I m p r o p e r a d j u s t m e n t V i b r a it o n

C o o il n g s y s t e m d i r t y / p l u g g e d

S p a r k a r r e s t o r s c r e e n p l u g g e d

N / A I

E x t e n d e d d i r t y / d u s t y o p e r a l o c a it o n it o n s i n

N o r m a l w e a r n t e r n a l e n g i n e p r o b l e m

A d j u s t

C l e a n

S e e p e l a y c o e u r E c h o d e a l e r E n g i n e n o t d o e s c r a n k

S p a r k A r r e s t o r

S c r e e n

N / A

WARNING DANGER

Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open spark plug opening, otherwise serious personal injury may result.

TORAGE

Long Term Storage (over 30 days)

WARNING DANGER

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:

Store unit in a dry, dust free place, out of the reach of children.

WARNING DANGER

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.

Place the stop switch in the "OFF" position.

Remove accumulation of grease, oil, dirt and debris from exterior of unit.

Perform all periodic lubrication and services that are required.

Tighten all the screws and nuts.

Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor.

Remove the spark plug and pour 1/4 oz. (1/2 tablespoon) of fresh, clean, two-stroke engine oil into the cylinder through the spark plug hole.

A. Place a clean cloth over the spark plug hole.

B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.

C. Observe the piston location through the spark plug hole. Pull the recoil starter handle slowly until the piston reaches the top of it's travel and leave it there.

Install the spark plug (do not connect spark plug cable).

NOTES

RASS

RIMMER

PERATOR

ANUAL

ERVICING

NFORMATION

PARTS

Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO

Dealer. When you do need to buy parts always have the Model

Number, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below.

Model No. _____________ Type _________SN. ______________

SERVICE

Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our

Web Site. When presenting your unit for Warranty service/repairs, proof of purchase is required.

ECHO CONSUMER PRODUCT SUPPORT

If you require assistance or have questions concerning the application, operation or maintenance of this product you may call the ECHO

Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit to help your Consumer Product Support Representative.

WARRANTY REGISTRATION

DEALER?

Call

1-800-432-ECHO or www.echo-usa.com

CONSUMER PRODUCT

SUPPORT

1-800-673-1558

8:30 - 4:30 Mon - Fri C.S.T.

You may register your Echo equipment using the warranty registration card or register on-line at www.echo-usa.com. Registering provides a direct link between you and ECHO if we find it necessary to contact you.

ADDITIONAL OR REPLACEMENT MANUALS

Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at www.echo-usa.com.

Operator's and Parts Manuals are available by:

• Downloading free from www.echo-usa.com

• Purchasing from your Echo Dealer.

• Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO,

INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address below.

Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.

Available Parts Catalog

GT-2000R Type 1E S/N 001001 UP Part Number 99922203440

ECHO, INCORPORATED

400 O

AKWOOD

R

OAD

L

AKE

Z

URICH

, IL 60047-1564 www.echo-usa.com

Halo! Saya adalah chatbot AI yang secara khusus dilatih untuk membantu Anda dengan ECHO GT-2000R Type 1E Grass Trimmer Manuel d'utilisation. Saya telah meninjau dokumen secara menyeluruh dan dapat membantu Anda menemukan informasi yang tepat yang Anda butuhkan atau menjelaskan konten dengan istilah yang jelas dan sederhana. Apakah Anda mencari panduan tentang fitur tertentu, langkah-langkah pemecahan masalah, atau penggunaan umum, jangan ragu untuk mengajukan pertanyaan Anda. Semakin banyak detail yang Anda berikan tentang kekhawatiran atau kebutuhan Anda, semakin akurat dan efektif saya dapat membantu Anda!

Asisten sedang mengetik

Asisten sedang tidak ada di depan keyboard. Silakan coba lagi nanti.

Daftar isi

Sepertinya Anda telah mencapai dokumen yang ditulis dalam beberapa bahasa, termasuk salah satu yang bukan bahasa asli Anda. Anda dapat menggunakan tautan berikut untuk sementara menyembunyikan halaman tanpa bahasa yang Anda sukai.