Element Electronics 32LE30Q User's Manual

Element Electronics 32LE30Q User's Manual
CAUTION: Changes or modifications not
expressly approved by the party
responsible for compliance with the
FCC Rules could avoid the users’
authority to operate this equipment.
CAUTION: The TV shall not be exposed to
dripping or splashing. No objects
filled with liquids, such as vases, shall
be placed on the TV.
CAUTION: Do Not Place This TV on an
unstable cart, stand, or table. The
TV may fall, causing serious injury
to a child or adult, and serious damage
to the TV. Use only with a cart or stand
recommended by the manufacturer, or
sold with the TV.
CAUTION: Installation on concrete wall has passed
UL safety test.
1
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.
WARNING: THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES SHALL BE PLACED ON THE APPARATUS.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT IN
OUTLET.
CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE
PERSONNEL ONLY.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING
ACTIVITIES, BUT CALL QUALIFIED ELECTRICIAN PERSONNEL.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED, REPLACE ONLY
WITH THE SAME OF EQUIVALENT TYPE.
2
IMPORTANT SAFETY INSTRUCTIONS
1.
READ THESE INSTRUCTIONS.
2.
KEEP THESE INSTRUCTIONS.
ON OR PINCHED PARTICULARLY AT PLUGS,
3.
HEED ALL WARNINGS.
CONVENIENCE RECEPTACLES, AND THE POINT
4.
FOLLOW ALL INSTRUCTIONS.
WHERE THEY EXIT FROM THE APPARATUS.
5.
DO NOT USE THIS APPARATUS NEAR WATER.
10. PROTECT THE POWER CORD FROM BEING WALKED
11. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED
Do not use this TV near water. For example, do not use near
a bathtub, washbowl, kitchen sink or laundry tub, in a wet
6.
BY THE MANUFACTURER.
12. USE ONLY WITH CART, STAND, TRIPOD, BRACKET, OR
basement, or near a swimming pool, and the like. The TV set
TABLE SPECIFIED BY THE MANUFACTURER, OR SOLD
shall not be exposed to dripping or splashing. No objects
WITH THE APPARATUS. WHEN A CART IS USED, USE
filled with liquids, such as vases, shall be placed on the TV
CAUTION WHEN MOVING THE CART/
set.
APPARATUS COMBINATION TO AVOID
INJURY FROM TIP-OVER.
CLEAN ONLY WITH DRY CLOTH.
Do not place this TV on an unstable cart, stand, tripod,
Unplug the TV from the wall outlet before cleaning. Do
bracket, or table. The TV may fall, causing serious injury to
not use liquid cleaners or aerosol cleaners. Use a
someone, and serious damage to the appliance. A TV and
damp cloth for cleaning.
7.
cart combination should be moved with care. Quick stops,
DO NOT BLOCK ANY VENTILATION OPENINGS.
excessive force, and uneven surfaces may cause the TV and
INSTALL IN ACCORDANCE WITH THE
cart combination to overturn.
MANUFACTURER`S INSTRUCTIONS.
13.
UNPLUG THIS APPARATUS DURING LIGHTNING
Slots and openings in the cabinet back or bottom are
STORMS OR WHEN UNUSED FOR LONG PERIODS
provided for ventilation, to ensure reliable operation of the TV
OF TIME.
and to protect it from overheating. These openings must not
be blocked or covered. The openings should never be
blocked by placing the TV on a bed, sofa, rug, or other
similar surface. This TV should never be placed near or over
For added Protection for this TV receiver during a lightning
storm, or when it is left unattended and unused for long
period of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
a radiator or heat resource. This TV should not be placed in a
TV due to Lightning and power line surges.
built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's instructions
have been adhered to.
14. REFER ALL SERVICING TO QUALIFIED SERVICE
PERSONNEL. SERVICING IS REQUIRED WHEN THE
APPARATUS HAS BEEN DAMAGED IN ANY WAY, SUCH
8.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS
RADIATORS, HEAT REGISTERS, STOVES, OR OTHER
APPARATUS (INCLUDE AMPLIFIERS) THAT PRODUCE
HEAT.
9.
DO NOT DEFEAT THE PURPOSE OF THE POLARIZED
OR GROUNDING-TYPE PLUG. A POLARIZED PLUG HAS
TWO BLADES WITH ONE WIDER THAN THE OTHER. A
AS POWER-SUPPLY CORD OR PLUG IS DAMAGED,
LIQUID HAS BEEN SPILLED OR OBJECTS HAVE
FALLEN INTO THE APPARATUS, THE APPARATUS HAS
BEEN EXPOSED TO RAIN OR MOISTURE, DOES NOT
OPERATE NORMALLY, OR HAS BEEN DROPPED.
Note: All figures in the manual are for reference only, please
refer to the actual units to determine their appearance.
GROUNDING TYPE PLUG HAS TWO BLADES AND A
THIRD GROUNDING PRONG. THE WIDE BLADE OR THE
THIRD PRONG IS PROVIDED FOR YOUR SAFETY. IF
THE PROVIDED PLUG DOES NOT FIT INTO YOUR
OUTLET, CONSULT AN ELECTRICIAN FOR
REPLACEMENT OF THE OBSOLETE OUTLET.
3
CLEANING AND MAINTENANCE
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
If the surface is particularly dirty, soak a soft, lint-free cloth in a weak detergent solution and then remove
excess liquid. Use this cloth to wipe the surface of the display panel, and then wipe it with a dry cloth,of the
same type, until the surface is dry.
Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid contact
with volatile substances such as insect sprays, solvents and thinner; otherwise, the quality of the surface may
be adversely affected.
Please read all the safety and operating instructions carefully before begin.
4
Table of contents
TABLE OF CONTENTS
CAUTION AND WARNING………………………………………………….…………..
1
IMPORTANT SAFETY INSTRUCTIONS………………..………………..………..…..
3
CLEANING AND MAINTENANCE………………………………………….…………….
4
SAFETY PRECAUTIONS..…………………………………………………….…………..
6
INSTALLATION……………………………………………………………….….………....
7
Preparation for using your new TV ……………………………………….…………...
8
FRONT PANEL………………………………………………………….……….…………
8
REAR PANEL…………………………………………………………………….....……...
9
CONNECTIONS AND EXTERNAL INPUT SETTINGS…………………………..….……….
10
Using the Remote control…………………………………………………..……………
11
LEARNING ABOUT REMOTE CONTROL…………………………………..………………
11
REMOTE CONTROL INSTRUCTIONS………………………………………..…………….
12
Basic operation……………………………………..………...……………………..……
13
TURNING ON AND OFF THE TV…………….……………………………..……………….
13
CHOOSING TV CHANNEL………………………………………..………..……………….
13
SELECTING INPUT SOURCE……………………………………………..………………...
14
VOLUME ADJUSTMENT..............................................................................................
14
Setup menu operation……………………………………..………...……………………
15
ADJUST THE OSD SCREEN……………………………………….….……………………
15
SELECT ON SCREEN LANGUAGE…………………….…………….….………………….
16
PICTURE MENU OPTIONS ……………………………………………..…….…………….
16
AUDIO MENU OPTIONS…………………….…………………………..………….……….
17
SETUP MENU OPTIONS…………………………….…………………..………………….
18
FEATURE MENU OPTIONS……………………………………..……..……………..…….
20
VGA MENU OPTIONS…………………………………………………....……..……….….
25
YPBPR MENU OPTIONS………………………….…………………..…………………….
26
HDMI MENU OPTIONS……………………………………………..........….……………...
27
APPENDIX …………………………………………………………..……..……………….
28
Troubleshooting…………………………..…….………..…………………………………
28
Removing TV Stand……………………………………..…………………………….…..………….....
31
Wall Mounting Unit Specification…………………….…….……………...……..……......
32
Universal Remote Control Code List …………..………………………………………..................
33
TV Specification………………………………………………..…………….…….…..………………...
34
5
Safety Precautions
SAFETY PRECAUTIONS
WARNING
KEEP UNNEEDED SMALL PARTS AND OTHER OBJECTS OUT OF THE REACH OF
SMALL CHILDREN. THESE OBJECTS CAN BE ACCIDENTALLY SWALLOWED. ALSO,
BE CAREFUL ABOUT PACKAGING MATERIALS AND PLASTIC SHEETS.
Set up
Do not place the TV set on sloped or unstable surfaces.
Do not place any objects on top of the TV set. If water spills onto the TV set or foreign objects get inside it,
short-circuiting may occur which could result in fire or electric shock. If any foreign objects get inside the TV set,
please consult an Authorized Service Center.
Do not cover the ventilation holes. Doing so may cause the TV set overheated and can cause fire or damage to the
TV set.
Avoid installing this product near electronic equipment that is readily affected by electromagnetic waves.
It may cause interference in image, sound, etc. In particular, keep video equipment away from this
product.
AC Power Supply Cord
Securely insert the power cord plug as far as it will go. If the plug is not fully inserted, heat may be generated which
could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used.
Do not handle the power cord plug with wet hands. Doing so may cause electric shocks.
Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the
cable.
Do not make any modifications to, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull
the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage
to the cable is suspected, have it repaired at an Authorized Service Center.
If the TV set will not be used for a long period of time, unplug the power cord from the wall outlet.
If Problems Occur During Use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the TV set,
unplug the power cord immediately. Continued use of the TV under these conditions might cause fire or permanent
damage to the unit. Have the TV evaluated at an Authorized Service Center. Service to the TV by any unauthorized
personnel is strongly discouraged due to its high voltage dangerous nature. If water or foreign objects get inside the
TV set, if the TV set is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately.
Contact an Authorized Service Center for any repairs that need to be made.
6
Safety Precautions
When using the TV set
Do not bring your hands, face or objects close to the ventilation holes of the TV set. Top of the TV set is usually
very hot due to the high temperature of exhaust air being released through the Ventilation holes. Burns or personal
injuries can happen if any body parts are brought too close. Placing any object near the top of the TV could also
result in heat damage to the object as well as to the TV if its ventilation holes are blocked.
Be sure to disconnect all cables before moving the TV set. Moving the TV with its cables attached might damage
the cables which, in turn, can cause fire or electric shock.
Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning.
electric shocks can result if this is not done.
Clean the power cable regularly to prevent it from becoming dusty. Built-up dust on the power cord plug can
increase humidity which might damage the insulation and cause fire. Unplug the cord from the wall outlet and
clean it with a dry cloth.
This TV set radiates infrared rays; therefore, it may affect other infrared communication equipment. Install your
infrared sensor in a place away from direct or reflected light from your TV set.
INSTALLATION
Selecting a location for the TV
1.
Place the TV on the floor or on a sturdy platform in a location where light does not directly hit the
screen.
2.
Place the TV far enough from the walls to allow proper ventilation. Inadequate ventilation may cause
overheating, which may damage the TV.
Optional External Equipment
Before you purchase any cables, be sure you know what type of output and input connectors your various
components require. Also determine the length of cable you will need. For more information regarding
cables, please refer to the Quick Start Guide.
7
Preparation for using your new TV – Front Panel
FRONT PANEL
Familiarizing Yourself with the Main Hardware
(The picture of the product may vary depending on the model)
a.
Select signal input.
(It changes to “ENTER” function when main menu displays )
b.
Main Menu display and menu selection
c.
Channel up
d.
Channel down
e.
Volume up
f.
Volume down
g.
ON/OFF button
8
Preparation for using your new TV – Rear Panel
REAR PANEL
Rear panel
(The picture of the product may vary depending on the model)
HDMI Input
S-Video Input
-
Input1 : J
-
Video : M
-
Input2 : K
-
Audio : D, D1
Component Input 1
VGA input
-
Video : E1, F1, G1
-
Video : I
-
Audio : B, B1
-
Audio : H (3.5mm plug)
Component Input 2
Others
-
Video : E, F, G
-
Power Input: A
-
Audio : C, C1
-
COAX Digital Out: N
-
External Antenna: O
Composite Input
-
Video : L
-
Audio : D, D1
9
Preparation for using your new TV – Connections
CONNECTIONS AND EXTERNAL INPUT SETTINGS
1. Checking Items before Connecting
Please check the list below before connecting the product to other devices.
< Check items before connecting. >
Check the instruction manual when connecting external devices. External products sometimes have different
buttons and locations.
A.
Do not connect the power unless every connection is well connected. The product may be
damaged if turned on while still in the process of being connected.
B.
Connect the left (white) and right (red) cables correctly to the sound cable.
C.
Check the terminals to connect the product to on the rear panel.
2. Connecting an Antenna
There are internal and external types of antenna.
< Connecting an Antenna>
Cable TV network
A.
Use a coaxial cable to connect the rear panel of the TV's [AIR] or [CABLE] terminals and the wall
mount or external antenna.
B.
When an Air signal is required, connect to the [AIR] terminal. If a Cable signal is required,
connect to the [CABLE] terminal. If both Air and Cable are available, and then connect both
[AIR] and [CABLE] terminals.
C.
Connect the TV power cord when connecting everything else.
CAUTION
Avoid bending the copper tip at the center of the coaxial cable.
10
Using the remote control – Learning about remote control
LEARNING ABOUT REMOTE CONTROL
1.
POWER: Power on/off.
2.
SLEEP: Press to select a preset time interval to
3.
ASPECT: Press to adjust the screen size.
4.
DISPLAY: Press to Check your current mode.
5.
MTS: Press to select your favorite language in
automatically shut the TV.
digital broadcasting.
6.
DTV: Press to change between Analog TV and
Digital TV.
7.
FAV: Add/delete the current channel to your
favorite channel.
8.
FAV.+: Press to view the next favorite channel.
9.
FAV-: Press to view the previous favorite
channel.
10. Numberic Buttons: Press to change the
channel directly using the numberic buttons.
11. RECALL: Press to switch between the current
channel and the last channel.
12. -: When selecting a digital broadcast channel,
press the number, followed by “-” button,
followed by sub channel number.
13. EPG: One of signal channel EPG or Multi
channel EPG.
14. PICTURE: Press to change to a preset picture
mode.
15. SOUND: Press to change to a preset sound
mode.
16. INPUT: Press to Display a menu of all available
input sources, Also used to confirm your choice
in the on-screen menu.
17. ENTER: Enter and confirm button.
18. UP/DOWN LEFT/RIGHT: The direction keys.
19. MENU: Press to display main menu.
20. MUTE: Press to temporarily switch the sound
off.
21. FREEZE: Press to freeze the current picture.
22. CC: Press to select Caption.
23. VOL+/-: Volume control buttons.
24. CH+/-: Channel control buttons.
11
Using the remote control – Remote control instructions
REMOTE CONTROL INSTRUCTIONS
< Inserting the batteries into the remote control >
1.
Push the back of the remote control.
2.
Pull forward slightly.
3.
Insert two AAA 1.5V batteries.
4.
Ensure the correct polarity (+/-).
5.
Close the lid.
CAUTION: Use only Alkaline Batteries.
z If the remote control is not working, see the checkpoints below.
z Are the polarities of the batteries (+, -) correct?
z Are the batteries worn out?
z Is there an AC power failure?
z Is the power cable plugged in?
z Is any special fluorescent or neon sign board turned on?
< Remote Control Reception Angle>
Use the Remote control within a range of 7~10m and at an angle of 30° to either side of the receiver.
CAUTION
z Used batteries should be recycled.
z Kept out of children's reach.
z Do NOT use new and old batteries together.
z Change both batteries at the same time.
z When not using the remote control over a long time, remove the batteries from the unit.
z Use only Alkaline battery.
12
Basic operation – Choosing TV Channel
TURNING ON AND OFF THE TV
TURN ON LCD TV
1.
Connect the AC input cable to power to the LCD TV. At this time the TV will enter standby mode and indicator show red.
2.
User POWER button or
3.
Wait 5 second after switch off LCD TV then you can turn on LCD TV again.
button on the remote control.
CHOOSING TV CHANNEL
1.
2.
Using the CH + / CH - on the front panel or on the remote control.
z
Press CH + to increase channel number.
z
Press CH - to decrease channel number.
Using 0-9 digital buttons and – button
You can select the channel number by pressing 0 to 9.
3.
For example:
IN ANALOG SIGNAL:
To select channel (e.g. Channel 22): Press 2 -> 2 ->ENTER,It will jump to 22-0 directly.
IN DIGITAL SIGNAL:
To select digit channel (e.g. Channel 22-1): Press 2 -> 2 -> - > 1 ->ENTER,the program will appear immediately.
NOTE: Sub channel number of analog channel is always zero. But when you in the digital signal, if you enter
physical channel number and not end with “ENTER”, channel selection will be made if there is no
operation within a few seconds.
13
Basic operation – Selecting input source
SELECTING INPUT SOURCE
You can select the input source by pressing the INPUT on the remote control or on the side panel.
VOLUME ADJUSTMENT
1.
Press VOL+/- to adjust the volume.
2.
If you want to switch the sound OFF, press the MUTE.
3.
You can cancel the mute function by pressing MUTE or VOL+/-.
14
Setup menu operation – Adjust the OSD screen
ADJUST THE OSD SCREEN
Press the MENU button to display the main menu.
Use
/
/
/
buttons to select and adjust the available menus.
NOTE: The OSD (On Screen Display) function enables you to adjust the screen status conveniently
until it provides graphical presentation.
When the cursor stays on a main menu function (Picture, Audio, Setup or Feature), you need to use
ENTER or button to activate it. After activating, the cursor will go forward into the submenu,
which you can use to choose the concrete functions with
/
button.
The images in this document may vary from your TV’s menu depending on the model. We provide
the instruction manual for better understanding and operation to the TV set. Therefore, all the
pictures here are for reference only.
15
Setup menu operation – Screen Language & Picture Menu Option
SELECT ON SCREEN LANGUAGE
NOTE: If you use your LCD TV for the first time, you should select the language which will be used
for displaying menus and indications.
1.
Press MENU to display the main menu.
2.
Press
3.
Use
4.
Press ENTER button to select your desired language.
/
/
repeatedly to select the SETUP MENU.
and ENTER to select MENU LANGUAGE.
PICTURE MENU OPTIONS
NOTE: In this manual, the OSD (On Screen Display) may be different from your TV’s in colors.
Press the MENU on the front panel or on the remote control and then use
/
to select the PICTURE menu.
/
to select what you want to adjust in the PICTURE menu.
1. Use
2. Press ENTER button to adjust.
3. When you are satisfied with your adjustment. Press MENU to exit the main menu.
Picture Mode
Select the type of picture which best corresponds to your viewing requirements by selecting Picture Mode in PICTURE menu.
When you press
/
buttons on the remote control, may select the picture modes (User / Vivid / Bright / Standard).
16
Setup menu operation – Audio menu options
Contrast
Press ENTER button to select it and then use
/
to adjust the contrast of picture.
/
to adjust the brightness of picture.
/
to adjust the sharpness level of picture.
/
to adjust the color saturation.
/
to adjust the tint of picture.
Brightness
Press ENTER button to select it and then use
Sharpness
Press ENTER button to select it and then use
Color
Press ENTER button to select it and then use
Tint ( NTSC Input only)
Press ENTER button to select it and then use
Aspect Ratio
Press ENTER button to select the ratio of picture display such as Normal/Zoom/Wide and Cinema.
AUDIO MENU OPTIONS
Press MENU on the front panel or on the remote control and then use
/
/
to select the AUDIO menu.
1.
Use
to select what you want to adjust in the AUDIO menu.
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust.
Audio Mode
You can select the type of sound which best corresponds to your listening requirements by selecting sound in SOUND menu.
You may select the sound mode directly by pressing the SOUND button on the remote control.
17
Setup menu operation – Setup menu options
Audio Language
Press ENTER to one of the audio language such as English / French and Spain, but the condition is that the program system
has included the language code.
Bass
Press ENTER button to select it and then use
/
to increase or decrease the level of the lower-pitched sounds.
/
to increase or decrease the level of the higher-pitched sounds.
/
to adjust the audio output between left and right speakers.
Treble
Press ENTER button to select it and then use
Balance
Press ENTER button to select it and then use
Digital Audio Output
Press ENTER button to select the one of mode of the digital audio output such as PCM and RCW.
Auto Volume Adjust
Press ENTER button to adjust the volume automatically (TV and HDMI input only).
SETUP MENU OPTIONS
Press MENU on the front panel or on the remote control and then use
1.
Use
/
/
to select the SETUP menu.
to select what you want to adjust in the SETUP menu.
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust.
Tuning Band
Press ENTER button to select Air, Cable, Cable HRC, Cable IRC, or Cable Auto.
DTV Signal
DTV Signal menu will show the intensity of DTV signal.
User can adjust the direction and orientation of external antenna by checking DTV Signal.
18
Setup menu operation – Setup menu options
Auto Ch Search
Press
/
to move the cursor to the item to be selected (item selected highlighted in yellow). Press ENTER key to
enter your selection and scan. After the scan is finished, the following menu will display. The channels found the
automatically saved as below:
Note: If you want you exit the Auto Ch Search during the Auto search process, press MENU twice to exit.
Add On Channel Search
When the channels are found, use ENTER to add it to the cannel list.
Manual Channel Set
Press ENTER button to display a channel list that you can select channel as below:
Note: this image comes from a engineering sample. Please operate according to actual channel list in your TV.
Channel Labels
Allows you to name the channel that is selected. Use
/
to move and use
/
to change.
19
Setup menu operation – Feature menu options
Menu Language
To select language of the OSD such as English/ French and Spain.
Reset
Press ENTER to return to the factory setting.
FEATURE MENU OPTIONS
/
Press MENU on the front panel or on the remote control and then use
/
to select the FEATURE menu
1.
Use
to select what you want to adjust in the FEATURE menu.
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust.
Time Set
Time Set Mode
You can select one of auto and manual to set the time. When selected auto, the item of year/date and time will be disabled
and can not to adjust. When select the manual mode, you can press
/
/
/
to set the corresponding functions.
Time Zone
Press ENTER button to select it and then use
/
to select the time zone such as Pacific/ Alaska/ Hawaii/ Eastern/
Central/ Mountain.
20
Setup menu operation – Feature menu options
Sleep Timer
Press ENTER button to select it and then use
/
to select the amount of time before your TV turn off automatically and
press the ENTER that can select the 15’ / 30’ / 45’ / 60’ / 90’ / 120’ / 180’ / 240’ and OFF.
Advance Video Menu
Press ENTER to enter the advance video menu as below
z
Noise Reduction - Spatial: press
z
Noise Reduction -Speaker :press
/
to select on or off.
z
Noise Reduction-Temporal: press
/
to select on or off.
z
Color Temperature: press
z
3D Y/C: Enable/disable 3D digital comb filter for pressing
z
Blue screen: Select to turn on blue screen display when there is no signal. However we recommend not to use blue
/
/
to select on or off.
to select one of Normal/ Cool and Warm.
/
to select on or off.
screen long time. If the screen is not changed long time, it can hurt the panel.
Password Set
Press the ENTER to enter old password menu, and then input the number of 0-9 as below, and you can change the password
when you input the new on twice. And the original password is “0000”.
Note: In case of password oblivion or missing, we provide the all-purpose password 1470.
Parental Control
Press ENTER to enter the sub-menu and then uses the 0-9 to enter the correct password and the Parental Control Menu will
display.
21
Setup menu operation – Feature menu options
Note: Advanced Rating is only available in digital channel.
US Ratings
Press ENTER to enter the US Ratings as below
MPAA
Press ENTER to lock or unlock one of None/ G/ PG/ PG-13/ R/ NC-17 and X.
z None: No restrictions
z G: General Audience. This contains little or no violence, no strong language, and little or no sexual dialog or
situations.
z PG: Children under 13 should be accompanied by an adult.
z PG-13: Parental guidance suggested. Children under 13 should be accompanied by an adult.
z R: Restricted. Viewers should be 17 or older.
z NC-17: not classified. Viewers should be 17 or older.
TV Rating
Press ENTER to lock or unlock one of TV-MA/ TV-14/ TV-PG/TV-G/TV-Y7 and TV-Y.
z
TV-MA: Mature audiences only. This program may contain mature themes, profane language, graphic violence and
explicit and explicit sexual content.
z
TV-14: Parents strongly cautioned. This program may contain sophisticated themes, sexual content, strong
language and more intense violence.
z
TV-PG: Parents guidance suggested. The program may contain infrequent coarse language, limited violence,
some suggestive sexual dialog and situations.
z
TV-G: General audience. This contains little or no violence, no strong language, and little or no sexual dialog or
situations.
22
Setup menu operation – Feature menu options
z
TV-V7: Directed for older children. Themes and elements in this program may include mild physical or comedic
violence, or may frighten children under the age of seven.
z
TV-Y: All children. The themes and elements in this program are specifically designed for a very young audience,
including children from ages two six.
Canadian Ratings
Press ENTER to enter the Canadian Ratings as below
Canadian English
Press ENTER to lock or unlock one of E/ C/ C8+/ G/ PG/ 14+/ 18+.
z E: Expect No restriction.
z C: Children
z C8+: Viewers should be 8 or order.
z G: General Audience.
z PG: Parental guidance suggested.
z 14+: Restricted. Viewers should be 14 or older.
z 18+: Restricted. Viewers should be 18 or older.
Canadian French
Press ENTER to lock or unlock one of E/ G/ 8 ans+/ 13 ans+/ 16 ans+ and 18 ans+.
z E: Expect No restriction.
z G: For all.
z 8 ans+: Restricted. Viewers should be 8 or older.
z 13 ans+: Restricted. Viewers should be 13 or older.
z 16 ans+: Restricted. Viewers should be 16 or older.
z 18 ans+: Restricted. Viewers should be 18 or older.
23
Setup menu operation – Feature menu options
Advanced Parental Lock
When select the ON for Advance Rating, the Advanced Parental Lock will display.
Digital Closed Captions
This menu allows you to set the closed caption, and press ENTER to enter Closed Caption Options menu as below:
z Style: press
/
to select between Automatic and Custom, when you select automatic, the other options are
disable and can not be adjusted.
z Size: press
/
to select between Normal/ Large and Small.
z Font: press
/
to select between Default and from Front 1 to Font 7.
z Text Color: press
/
to select between Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
z Text Opacity: press
/
z Background Color: press
z Background Opacity: press
to select between the Solid/ Flashing/ Transparent/ Translucent.
/
to select o between Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
/
to select between Solid/ Flashing/ Transparent/ Translucent.
z Edge Effect: press
/
to select between None/ Raised/ Depressed/ Uniform/ Left Shadow/ Right Shadow.
z Edge Color: press
/
to select between Red/ Green/ Yellow/ Magenta/ Cyan/ Black and White.
24
Setup menu operation – VGA menu options
VGA MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming VGA on the top-right screen.
/
to select what you want to adjust in the FEATURE menu.
1.
Use
2.
Press ENTER button to select it and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust.
VGA Set
Press
/
button and then press ENTER to enter the VGA set menu as below
z H-Position
Press ENTER button to select it and then use
/
to adjust the horizontal position of the picture.
/
to adjust the vertical position of the picture.
/
to adjust the phase of the picture.
/
to adjust the clock of the picture.
z V-Position
Press ENTER button to select it and then use
z Phase
Press ENTER button to select it and then use
z Clock
Press ENTER button to select it and then use
Note:
Phase- This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Clock- This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal
25
Setup menu operation – YPBPR menu options
screen size also will change.
Position- This function is to adjust the picture to Left/ Right and Up/ Down as you prefer.
Auto Adjust
Press ENTER button to select it and then use
/
to do auto adjust that automatically adjusts the available options for the
best viewing configuration.
Setting
Press ENTER to do preset that can return to the factory setting.
YPBPR MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming “Component” on the top-right screen.
/
to select what you want to adjust in the FEATURE menu.
1.
Use
2.
Press ENTER button to select and then use
3.
When you are satisfied with your adjustment, press MENU to exit the main menu.
/
to adjust.
Component Set
Press
/
button and then use ENTER to enter the Component Set menu as below
26
Setup menu operation – HDMI menu options
HDMI MENU OPTIONS
Continuously Press [INPUT] on the remote control until coming “Component” on the top-right screen.
1. Use
/
to select what you want to adjust in the FEATURE menu.
2. Press ENTER button to select and then use
/
to adjust.
3. When you are satisfied with your adjustment, press MENU to exit the main menu.
Time Set
Press
/
button and then use ENTER the time set menu that allows you to set the time the TV will display.
Sleep timer
Press ENTER button to select it and then use
/
to adjust the amount of time before your TV turn off automatically and
press the ENTER that can select the 15min/30min/ 45min/60min/ 90min/120min/180min/240min and OFF.
Advance Video Menu
Press ENTER to enter the advance video menu.
27
Appendix-Troubleshooting
TROUBLESHOOTING
Identifying Problems
If there are any problems using the product, please first consult the list below. If the list below does not solve the problem, call our
Customer Service Center immediately.
Q: My television won't power on. What could be wrong?
A: Make sure your power cord is firmly plugged into both the back of the TV and the power outlet. Some models have a power
switch on the back of the TV - make sure it is in the ON position. If you are trying to turn on your TV using the remote control,
make sure you are using new batteries and that they are inserted properly. On Universal Remote controls, first press the “TV”
button on remote control, and then press the POWER button.
Q: How to I get to the TV Channels I want?
Your new TV has to search for channels during the initial Start-Up phase. Please follow the Channel Programming/Auto Scan
portion of the Users Manual.
Q: I have everything connected, but there is no picture or sound?
A: Make sure all cables are firmly connected into your television and your external AV sources. After you have made all
connections, press the INPUT or SOURCE button on either the TV or the remote and choose the correct source. Make sure
your cable, satellite, or set-top box is turned on. If these step fail, try a different set of cables.
Q: I have sound with no picture.
A: Make sure all cables are firmly connected into your television and your external AV source. After you have made all
connections, make sure the sound input matches the video input. If you are trying to view a TV station, switch to another
station because some channels may be having broadcast difficulties. Check to make sure the brightness/contrast settings are
correct by entering the main menu and adjusting.
Q: I have picture with no sound.
A: Make sure the television is not muted. Check all cables to ensure they are firmly connected into the TV and your eternal
AV source. After you have done so, check to see that the video input matches the sound input. Increase the volume on either
the remote control or TV. If you are trying to view a TV station, switch to another station because some channels may be
having broadcast difficulties.
Q: I am experiencing poor picture quality or static. What could this be?
A: Interference may be causing poor picture quality or static. To remedy this you may try moving any infrared equipment
away from the television. Make sure all cable connections are secure and that the cables are working correctly. If you are
experiencing noise or ghosting during cable or satellite broadcasts, switch to another TV station because some channels may
be having broadcast difficulties.
Q: My remote control is not working or only works when I am close to the television.
A: Make sure you are using new batteries and that they are inserted correctly. Your remote will operate 16 ft. away from the
television, and 30 degrees from center in either direction. Make sure you are trying to operate the remote in this range.
Q: I lost my Manual, Quick Start Guide, Warranty Card, Remote Control Guide, or other material. Where can I find
another one?
A: Product support materials for your TV can be downloaded on the Element Electronics web site
(www.elementelectronics.com) under the Support option.
28
Appendix-Troubleshooting
Q: I opened the box and an accessory was missing. What do I do?
A: Please call our Customer Service team so we can get you a replacement. Go to the “Contact Us” portion of the web site
and enter your model number to obtain the correct customer support phone number.
Q: Why am I getting a black square in the center of my television screen?
A: The Closed Caption function is set in the “text” mode. To remove it, access Closed Caption in the Main Menu and change
the Mode setting from “text” to “off”.
Q: On some channels I am getting another language or sometimes no sound at all.
A: That would indicate that the MTS mode on your unit is set to “SAP” mode. We suggest setting the MTS mode to either
“Stereo” or “Mono”. For further instruction, please see “Audio Adjust” or “Multi-channel TV Sound (MTS)” in your User's
Manual.
Q: When I turn off my television, there is a white flash on the screen. Is this normal?
A: Yes, this is normal. That is the LCD backlight powering down.
Q: I have connected an external AV source to my television and I get no picture and/or sound.
A: Make sure to connect the cables to the correct outputs on your external AV source and the inputs on your television. Press
the INPUT or SOURCE button to select the input mode that corresponds to your connection to the external AV source. Turn
on your external AV source. Check for the correct settings in the Audio Select menu on your TV.
Q: I can't control my television with my current remote control.
A: Check to see that the television is still plugged in to the outlet. If you have a television with a universal remote, be sure to
select the TV mode on the remote. If the remote still does not work, reset the remote by removing and reinserting the
batteries (assuring the batteries are installed in the correct position). Then press the power button down for 30 seconds. If the
problem still exists, replace the batteries if needed.
If you have reset or changed the batteries in a universal remote control, you will need to reprogram the remote for the TV and
other units.
Q: I currently receive digital cable from my cable company.
Isn't that HDTV?
A: Many Cable TV companies use the term “digital cable” to refer to the digital compression which allows them to provide
more analog channels. It does not necessarily mean they are providing an HDTV signal. Contact your service provider to
learn more about HDTV programming packages.
Q: I get a grainy picture when cable is hooked-up directly to my TV using an RF cable.
A: To improve your picture, try the following:
Replace the cable that connects the TV to the cable outlet.
Check for breaks or damage to the cable, both indoors and out. If the cable is damaged, replace it.
Check the center pin at the end of the cable you attach to your TV. Make sure it is straight and long enough to make a good
connection.
Make sure you are using the correct cable setting for your area.
If you use a cable box, make sure your TV is tuned to the proper station. Most often this is channel 3. Sometimes, it is
channel 4.
If these options don't improve your picture, you may need to run a new cable. Contact your service provider to learn more.
Q: Why am I only receiving my local stations when I have cable?
A: You may need to run the Auto Tuner Scan again and make sure that Cable is highlighted instead of Air. For instructions on
doing so, consult your User's Manual or call Element Electronics helpful technical support line.
Q: Why do I still see black bars on my widescreen TV when viewing certain widescreen DVDs and HDTV
broadcasts?
A: Your widescreen TV has an aspect ratio of 16:9 (1.78:1), which is the aspect ratio of HDTV. However, movies are filmed at
several different aspect ratios, including 2.35:1. Also referred to as "scope", 2.35:1 is a panoramic aspect ratio that provides a
29
Appendix-Troubleshooting
wide field of view in the theater. Scope is much wider than your widescreen TV, so it still requires the use of letterboxing
("black bars") to fit the entire image on screen. Some TVs and DVD players have a zoom function that allows you to blow up
the image so it fills the screen, but the sides of the image must be cropped in order to do so.
Q: My TV is making a buzzing/humming noise. How do I make it stop?
A: This noise is normal and within the FCC standard for acoustic noise standard. The noise should be within the allotted
30dB/A level for audio. If you think the noise is excessive, call the Element Electronics technical support line.
Q: No audio on local channels?
A: Your TV is designed to receive Stereo broadcasts. It is also capable of receiving SAP (Second Audio Programs) available
from TV stations. Some stations broadcast radio stations, weather, foreign language or nothing at all on this frequency. If
your TV was mistakenly set to receive SAP, then you may be getting the wrong audio or no audio on some stations. To
alleviate this problem access the MTS STATUS screen of your TV MENU and make sure you highlight STEREO instead of
SAP. This should solve the problem.
30
Appendix-Removing TV Stand
Removing TV Stand
If you decide to install the wall mount your LCD TV, always use a VESA standard wall mount appropriate
for the size and weight of the LCD TV.
CAUTION
z Be sure to follow the instructions. Incorrect installation of the stand/wall mount may result in the
TV falling over.
z Before attaching (or detaching) the stand, unplug the AC cord from the AC input terminal.
z Unplug and remove any cables and/or other component connectors from the rear of the TV.
NOTES
Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as
described in the instructions provided with the wall bracket. Extreme care should always be used when
removing the stand/wall mount to avoid damage to the LCD panel.
As shown below:
(The picture may vary depending on the model.)
PROCEDURE
1. Place the TV set on a surface that is totally stable, flat and smooth(such as a
table). The front panel of TV should face the surface. Remove 6 screws signed in red circles.
2. Draw out the stand gently.
31
Appendix-Wall Mounting Unit Specification
Wall Mounting Unit Specification
Unit Dimension(unit: mm)
400x200
Screw Diameter
Screw Length(unit: mm)
M5
12
Remark: The specification of screw is just used on the back cabinet.
NOTE: Wall mount bracket is not included with TV and mounting of wall mount bracket to wall may
vary depending on brand and size of bracket. Customer should consult bracket mounting
instructions that came with wall mount for specific information on how to mount bracket to wall.
Before reading the installing instruction, please notice:
A. The wall mount is not contained in the accessories sold with television. We only provide the installing
specifications but not the wall mount itself. If you need the mount, please consult with the local dealer
for the assorted fitting parts.
B. We strongly suggest to set the wall mount with equipments of specification we ordered. If not,
inappropriate installing may cause damage to the device.
32
Appendix-Universal Remote Control Code List
UNIVERSAL REMOTE CONTROL CODE LIST
For Universal Remote Control brands listed below, please use accompanying codes and refer to your
Universal Remote Control User Manual for basic instruction for changing TV code to operate TV
model.
z
z
z
Codes for Sony TV = 8003, 8012, 8058
Codes for Philips TV = 1005, 1006, 1007, 1035, 1064, 1216
Codes for other universal remotes = 272, 132, 134, 116, 040, 016, 024, 056, 019, 262
33
Appendix-TV Specification
TV SPECIFICATION
Model
32LE30Q
Diagonal display size
32 inches
Television system
American TV standard ATSC /NTSC system
Audio multiplex
BTSC system
VHF: 2~13
Channel coverage
UHF: 14~69
CATV:1~125
Digital Terrestrial Broadcast (8VSB): 2~69
Digital cable (64/256 QAM): 1~135
PC mode
640×480/60Hz, 800×600/60Hz, 1024×768/60Hz
YPbPr/YCbCr mode
480i/60Hz, 480p/60Hz, 720p/60Hz, 1080i/60Hz
HDMI Mode
480i/60Hz, 480p/60Hz, 720p/60Hz, 1080i/60Hz
Resolution
1366×768
Power source
AC 100 - 240 V, 50 - 60 Hz
Power consumption
Audio power
Less than 140W
8W + 8W
RF input:
Cable/ Antenna ×1
VIDEO input:
VIDEO ×1
S-VIDEO ×1
COMPONENT ×2
Connection Interface
HDMI ×2
GRAPHIC input: Analog RGB 15pin ×1
AUDIO Input:
AV Audio×1
Component Audio ×2
PC Audio Input ×1
AUDIO output: Digital audio output ×1
TV Dimensions
Height: 22.6inches
Width: 31.3inches
Depth: 9.2inches (With stand)
Package Dimensions
Height: 25.4inches
Width: 34.8inches
Depth: 10.2inches
NET Weight
33.9 lbs
Package Weight
40.9 lbs
Supplied accessories
User Manual, Warranty Card, Remote control, AC cord, Batteries, QSG
Design and specifications are subjects to change without notice.
CUSTOMER NOTICE: Use carefully when operating to prevent damage to the screen.
34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement