EPSON PowerLite 52c
®
®
Quick Setup
Connect the projector
to your laptop
For most setups, you’ll need just these two cables:
Power cord
1
2
Computer cable
Make sure your projector and laptop are turned off.
Connect one end of the computer cable to the
Computer/Component Video port on the projector.
Follow these instructions to connect the projector
to your laptop. To connect other devices, such as
a VCR or desktop PC, see your User’s Guide.
3
Connect the other end to your laptop’s video or
monitor port.
®
If you can’t connect the cable to your PowerBook, you may need
to use an adapter. See your User’s Guide for instructions.
Turn on your equipment
1
2
3
Connect the power cord to the back of
your projector and plug the other
end into an electrical outlet.
Remove the lens cover.
Press the red Power button. The power light
flashes green, and then stays on.
Caution: Before unplugging
the projector...
To shut the projector down properly:
4
1. Press the red Power button twice.
Let the projector cool while the
power light flashes orange
(about 45 seconds).
Turn on or restart your laptop. (Windows® only: If you
see this Add New Hardware screen, click Cancel.)
Lens cover
Power light
2. Once the light stops flashing and
stays on, it’s safe to unplug
the projector.
Never unplug the projector when
the power light is green or
flashing orange.
Turn over
Quick Setup
EPSON PowerLite 52c
®
Adjust the image
1
®
If you see a blank screen
Rotate the focus ring to sharpen the image.
If you see a blank screen or the No signal message
after turning on your laptop, check the following:
Make sure the power light is green and
not flashing and the lens cover is off.
Focus adjustment
No signal ( ? Help)
Try turning off the laptop and restarting it.
If you’ve connected more than one computer and/or video source,
you may need to press the Source button on top of the projector.
(Allow a few seconds for the projector to sync up after pressing it.)
Note: If you see a blank screen
to the right.
2
3
No signal ( ? Help)
, see the instructions
Move the projector closer to or farther from the screen to reduce or
enlarge the image.
To raise the image, press the blue foot release levers inward
and lift the front of the projector. Once the image is positioned
where you want it, release the levers to lock the feet in position.
If you’re using a Windows laptop:
Hold down the Fn button and press the function key that lets you
display on an external monitor. It may have an icon such as
,
or it may be labelled CRT/LCD. Allow a few seconds for the projector
to sync up after pressing it.
On most systems, the
key lets you toggle between the LCD
screen and the projector, or display on both at the same time.
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
Check your laptop’s manual or online help for details.
4
5
®
If you’re using a Macintosh with Mac OS 9:
If your image looks like
or
, you’ve placed the projector
off to one side of the screen, at an angle. Move it directly in
front of the center of the screen, facing the screen squarely.
If your image looks like
or
, adjust it by pressing the
side of the Keystone button on the projector.
Where to get help
Telephone Support Services
To use the EPSON PrivateLine® Support service, call (800) 637-7661
and enter the PIN on the EPSON PrivateLine Support card included in
your owner’s kit. This service is available 6 AM to 6 PM, Pacific Time,
Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing
one of these numbers:
U.S.:
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
1. From the Apple® menu, select Control Panels, then click Monitors
or Monitors and Sound.
or
Click here
2. Click the Arrange icon.
Drag one monitor icon
on top of the other
3. Drag one monitor icon on top of the other. This lets you display on
the projector screen as well as the LCD screen.
If the Arrange option isn’t available, you may need to select one
of the Simulscan resolution settings. See your User’s Guide
for instructions.
If You're Using a Macintosh with Mac OS X:
1. From the Apple menu, select System
Preferences, then click Displays.
Toll or long distance charges may apply.
Electronic Support Services
EPSON provides technical assistance through electronic support
services 24 hours a day at http://support.epson.com. For tips,
templates, and training for developing successful presentations
go to http://www.presentersonline.com.
2. Select the VGA Display or Color LCD
dialog box, click the Arrange (or
Arrangement) tab, and make sure
Mirror Displays is checked.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
EPSON disclaims any and all rights in those marks. Copyright © 2002 by Epson America, Inc. Printed in XXX
9/02
Click here
CPD-15174
">
