Epson Z8050WNL Operation Guide

PowerLite® Pro Z8050WNL

Network Operation Guide

Contents

2

Introduction

Making Effective Use of Your Projector . . . . . . . . . . . . . . . . . . . . . . . . . 6

Various Screen Transfers by Network Connection (EasyMP Network

Projection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using the Network Projection function in Windows Vista and Windows 7 . 6

Monitor, Configure, and Control the Projector from a Remote Location . . . 7

Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Software Supplied. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting with EasyMP Network Projection

EasyMP Network Projection Summary . . . . . . . . . . . . . . . . . . . . . . . . . 11

Main Functions of the EasyMP Network Projection . . . . . . . . . . . . . . . . . . . . . . 11

Two Connection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Advanced Connection Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Quick Connection Mode (Only when the optional Wireless 802.11a/b/g

Module is installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Steps for connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Preparing to Connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Preparing the Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

For Windows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

For Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting to a Projector on a Network and Projecting. . . . . . . . . 14

Operating the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operating the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Connection Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using the Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

EasyMP Network Projection Useful Functions

Projecting Only a PowerPoint Slide Show (Presentation Mode) . . 22

Projecting Movies from a Computer (Movie Sending Mode) . . . . . 23

Supported File Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Playing Back a Movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using Multi-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Example of Adjusting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Procedure Before Using the Multi-screen Display Function. . . . . . . . . . . . . . . 27

Setting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Enable the virtual display driver (Windows only) . . . . . . . . . . . . . . . . . . . . . . 27

Adjusting the Virtual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Allocating the Image to be Projected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Projecting the Allocated Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Connecting to a Projector on a Different Sub-net

Connecting to a Projector on a Different Subnet. . . . . . . . . . . . . . . . 35

Searching by Specifying the IP Address and Projector name (For

Advanced Connection Mode only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Performing a Search with a Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Making a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Searching by Specifying a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Managing a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3

Setting the EasyMP Network Projection Operation

Using Set options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting Each Item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

General settings tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjust performance tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Audio Output tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using the Network Projector Function to Project Images

Using Network Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Using a Computer to Set Up, Monitor and Control

Projectors

Changing Settings Using a Web Browser (Web Control) . . . . . . . . . 48

Displaying Web Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Entering the IP address of the projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Projector Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Items in the Configuration menu that cannot be set by the web browser

48

Items that can only be set in the Web browser . . . . . . . . . . . . . . . . . . . . . . . . 49

Using the Mail Notification Function to Report Problems . . . . . . . 50

Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Appendix

Connection Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Display Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Number of Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

When Using Windows Vista and Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Limitations when projecting from Windows Photo Gallery . . . . . . . . . . . . 54

Limitations in Windows Aero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Limitations when projecting from Windows Media Center . . . . . . . . . . . . 54

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Problems Concerning Network Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Cannot connect using EasyMP Network Projection. . . . . . . . . . . . . . . . . . . . 56

When a connection is made using EasyMP Network Projection, the projected image remains as is, and a connection cannot be made from another computer.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

The projector is not found when EasyMP Network Projection is started.56

Cannot connect in Advanced Connection Mode or Wired LAN connection

58

The Slide Show cannot be displayed on the desired display when the multi-screen display function is being executed. . . . . . . . . . . . . . . . . . . . . . . 58

Applications are no longer displayed from the computer screen when the multi-screen display function is executed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

The mouse cursor is not displayed on the computer screen. . . . . . . . . . . . 59

When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

When a connection is made using EasyMP Network Projection, a

PowerPoint Slide Show cannot be started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

When a connection has been made using EasyMP Network Projection, the screen will not be refreshed when using an Office application. . . . . . . . . 60

Error message when starting up EasyMP Network Projection . . . . . . . . . . 60

Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection. . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Problems Concerning Monitoring and Control . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Mail is not sent even if a problem occurs in the projector. . . . . . . . . . . . . . 62

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Copyright Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

4

Introduction

This chapter provides information on functions that allow you to use your projector more effectively via a network.

5

Making Effective Use of Your Projector


The following functions in EasyMP (Epson Administrative System for

Meeting and Presentation) can help you create varied and effective meetings and presentations.

Various Screen Transfers by Network Connection

(EasyMP Network Projection)

You can hold efficient meetings and presentations by connecting the projector to a network using EasyMP Network Projection.

Install the software from the supplied "EPSON Projector Software for

Meeting & Monitoring" CD-ROM in advance to execute EasyMP

Network Projection. s

p.8

6

• Easy preparation/Information security administration

Because you can project materials stored on a shared file server or on your desktop from a computer in the conference room that is connected to a network, you do not need to make copies of data in advance.

Also, because you do not need to copy the data into a USB memory or notebook PC and carry them around, your information is securely protected.

• Smooth progress

If the projector is connected to a network, you can share the projector from computers on the network. You can project data from different computers during a meeting or presentation without changing the signal cable between computers. Even a distance between the projector and the computer does not cause any problems.

• Various screen transfer functions

• Distribution function s

p.11

• Switching function s

p.11

• Presentation Mode s

p.22

• Multi-screen display s

p.25

Using the Network Projection function in Windows

Vista and Windows 7

You can use the Network Projector function in Windows Vista and

Windows 7 to connect the projector and a computer via a network and project images. This lets you make presentations via a network by simply using a standard OS function without installing any software. s

p.45


Monitor, Configure, and Control the Projector from a

Remote Location

The following convenient functions collectively manage projectors in various conference rooms.

• Receive an e-mail notification if a problem occurs s

p.50

• Monitor and detect problems from SNMP Manager on the networks

p.51

• Set and control the projector by using a standard computer Web browser s

p.48

7

Installing the Software


You can find the software for using the projector effectively on the supplied "EPSON Projector Software for Meeting & Monitoring"

CD-ROM. Install the software on the computer you are using.

Software Supplied

You can find the following software on the "EPSON Projector Software for Meeting & Monitoring" CD-ROM.

• EasyMP Network Projection

Software for sending computer screen images to a projector via a network connection.

• EasyMP Monitor

Software that lists the current status of Epson projectors connected to the network, and monitors and controls those projectors. You can collectively manage multiple projectors by using EasyMP Monitor. For details on using EasyMP Monitor, see the EasyMP Monitor Operation

Guide.

Check the system requirements for each software application from

"Software System Requirements" in the User's Guide.

Installing

Make sure you check the following points before starting installation.

• When you using the following OS, you must have administrator authority to install EasyMP Network Projection.

• Windows 2000

• Windows 7

• Windows XP • Windows Vista

• When you using the following OS, you must have administrator authority to install EasyMP Monitor.

• Windows 2000

• Windows XP

• Windows 7

• Windows NT4.0

• Windows Vista

• Make sure that you close all running applications before starting installation.

• Consult the network administrator about the administration of the network and computers or whether or not applications can be installed on the computer.

q • For EMP NS Connection users

The EasyMP Network Projection software that came on your new projector software CD-ROM provides updated networking features and is backward-compatible with existing networks running Epson projectors. To use your new projector on the network, you must uninstall EMP NS

Connection and install EasyMP Network Projection software as described in this manual.

• For EMP Monitor users

The Easy Management® EasyMP Monitor software that came on your new projector software CD-ROM provides updated network monitoring features. To monitor your new projector on the network, you must uninstall EMP Monitor and install EasyMP Monitor. First save a copy of your current setting information data file, EMPMonitor.dat, in a separate folder. This will retain your current registered projector settings. Then uninstall EMP Monitor and install EasyMP Monitor as described in the

EasyMP Monitor Operation Guide. After installation, replace the new

EMPMonitor.dat file with your saved copy.

Procedure

For Windows

8


A

Turn on your computer.

B

Insert the "EPSON Projector Software for Meeting &

Monitoring" CD-ROM into the computer.

The installer starts automatically.

C

Click "Easy Install".

To select software and install it individually, select Custom Install.

To change the language in which the software is displayed, click

Language .

D

Check the applications to be installed, and then click

"Install".

E

When the License Agreement screen is displayed, click "Yes".

F

When the Add-Remove EPSON Virtual Display screen is displayed, click "OK".

To use Multi-screen display you need to set up EPSON Virtual Display. If you do not want to set it up now, you can do so later. s

p.26

G

Click "Exit" to complete the installation.

For Macintosh

EasyMP Monitor is not compatible with Macintosh computers.

A

Turn on your computer.

B

Insert the "EPSON Projector Software for Meeting &

Monitoring" CD-ROM into the computer.

C

Double-click the "ENPvx.xx_Installer" icon in the EPSON window.

Installation starts.

D

Click "Exit" to complete the installation.

q • When installation does not start automatically (Windows only)

Select Start - Run, and in the Run dialog box, type the letter for your

CD-ROM drive followed by :\EPsetup.exe and then click OK.

• Uninstalling

For Windows

Select Control Panel - Add-Remove Programs or Add or Remove

Programs and then remove EasyMP Network Projection.

For Macintosh

From Applications, delete the EasyMP Network Projection folder.

9

10

Connecting with EasyMP Network Projection

This section explains how to connect the computer and the projector via a network, and the procedure for projecting images from your computer's screen with the projector.

EasyMP Network Projection Summary

11


You can make meetings and presentations by using the following convenient functions.

• Switching function

The presenters can take turns and project their own images without changing cables.

EasyMP Network Projection needs to be installed on each computer to use this function.

Main Functions of the EasyMP Network Projection

• Presentation Mode s

p.22

This function can project a PowerPoint Slide Show running on a computer. A black screen is projected when the Slide Show is not playing.

• Multi-screen display s

p.25

You can project different images from up to four projectors from one computer, allowing you to project landscape images such as spreadsheets as one continuous image.

Two Connection Modes

There are two methods of connecting a computer and the projector via a network by using EasyMP Network Projection.

Advanced Connection Mode

Advanced Connection Mode is an infrastructure connection, and connects to an existing network system.

When connecting to a network via Wired LAN, connect the projector to the network hub with a commercially available LAN cable.

If you install the optional Wireless 802.11a/b/g Module in the projector, you can connect to the network via a wireless LAN access point.

• Distribution function

The screen being displayed by a remote computer can be simultaneously displayed by up to four projectors on the same network.


Quick Connection Mode (Only when the optional Wireless

802.11a/b/g Module is installed)

Quick Connection Mode only runs when you install the optional

Wireless 802.11a/b/g Module in the projector.

Quick Connection Mode temporarily assigns the projector's SSID to a computer creating an ad hoc

g connection, and restores the computer's

network settings after disconnecting. s

p.13

• You can easily connect to a computer and project images from the computer without making network settings.

• This lets you connect easily without a connector cable, and you can connect even if the projector and the computer are at remote locations.

Steps for connecting

Use the following steps to connect the projector to a computer and project images using EasyMP Network Projection.

12

You need to perform steps 1 to 4 only the first time you connect.

1.

Install EasyMP Network Projection on the computer to be connected. s

p.8

2 Make sure your computer is connected to the network. s

p.13

3.

To use "Quick Connection Mode": Install the optional Wireless

802.11a/b/g Module on the projector. (If it is already installed, go to step 5.)

To use "Advanced Connection Mode": Enable the Wired or Wireless

LAN adapter in "Port Configurations".

*

See your computer's documentation.

4.

Make network settings on the projector and put it into network connection status. See your User’s Guide for more information.

5.

Start EasyMP Network Projection on the computer and connect with the projector. s

p.14

* Select access point and the router settings if necessary.

Preparing to Connect

Preparing to Connect

Preparing the Computer

For Windows

Make network settings for the computer by using the utility software supplied with the LAN adapter. For more information on the utility software, see the User's Guide supplied with your LAN adapter or computer.

For example, as shown in the following illustration, when a red cross (^) is displayed over the network icon on the taskbar, you cannot connect to the projector.

For Macintosh

Set the network port and communication status. For more details on setting the communication status, see the User’s Guides for your computer or the AirPort card.

13

Connecting to a Projector on a Network and Projecting

14


Operating the Projector

Before connecting, put the projector into connection standby status.

Make sure the projector network settings are complete, and the projector is connected to network equipment such as a network hub via a commercially available network cable.

Procedure

A

Press the [t] button on the remote control to turn the power on.

B

Press the LAN button on the Remote Control.

The following LAN standby screen is displayed.

Operating the Computer

In the following explanations, unless otherwise noted, Windows screen shots are used. You see the same screens even when using Macintosh.

Procedure

A

Start EasyMP Network Projection.

For Windows

Select Start - Programs (or All Programs) - EPSON Projector -

EasyMP Network Projection .

For Macintosh

Double-click the Applications folder of the hard drive volume in which EasyMP Network Projection is installed, and then double-click the EasyMP Network Projection icon.

B

The Connection mode screen opens, select "Advanced

Connection Mode" or "Quick Connection Mode" (only available when the optional Wireless 802.11a/b/g Module is installed). Then click "OK".

The projector search results are displayed.

To always connect using the mode you selected, select Set the se- lected Connection Mode as the default mode for future connections.

in the Connection mode screen.


C

Select the projector you want to connect to, and then click

"Connect".

You can select up to four projectors connected to the same network and project the same images at the same time.

If the projector you want to connect to is not displayed in the search results, click the Automatic search button. The search takes about

30 seconds.

For details on the connection screen, see "Using the Connection

Screen". s

p.16

D

When Projector keyword is set to "On" from the projector, the keyword entry screen is displayed. Enter the keyword displayed on the LAN standby screen, and then click "OK".

When the connection is complete, the computer screen is projected. The following EasyMP Network Projection toolbar is displayed on the computer screen. You can use this toolbar to operate the projector and make settings, and to disconnect the network connection. For details on using the toolbar, see "Using the Toolbar". s

p.18

q When connecting from another computer, such as when changing presenters, start EasyMP Network Projection from the computer you want to connect. The computer that is currently connected is disconnected, and the projector is then connected with the computer that is trying to connect now.

15

Using the Connection Screen


Start EasyMP Network Projection to display the following screen. The operation of each button or item is described in the following table.

When the system starts in Advanced Connection Mode

When the system starts in Quick Connection Mode

16

A

B

Automatic search

In Advanced Connection Mode, you can search for available projectors on the network system that the computer is connected to.

In Quick Connection Mode, you can search for the projector based on the SSID.

Manual search

In Advanced Connection Mode, you can search for a projector based on a specified IP address or Projector name.

In Quick Connection Mode, you can search for the projector based on the SSID selected from a list.


C

Status

The following six icons indicate the status of the detected projectors.

Standby Select for connecting.

Busy Select for connecting. When you click

Connect, the computer currently connected is disconnected and your computer is connected.

Busy (Disable interrupt connection)

Cannot be selected. Disable

interrupt connection is set on another computer which is already connected.

Currently in use by another application

Searching

The projector's Configuration Menu is open. You can select it after closing the Configuration menu and running the search again.

Displayed while running Manual search or Profile.

Not found.

Displayed when a projector cannot be found as a result of Manual search or

Profile. In Quick Connection Mode, you can only select multiple projectors with the same SSID.

D

Projector name

The projector's name is displayed.

E

Disable interrupt connection

Check the box to prevent an interrupt connection by other computers while connected to the selected projector.

F

Use multi-display

Check the box to use the Multi-screen display function. When this is selected, Display layout and Display properties are displayed at the bottom of the screen. s

p.25

17

G

Troubleshooting

If there is a problem and you cannot have a connection, press this button to open the EasyMP Network Projection Troubleshooting screen.

H

Connect

Connect to the projector you selected from the search results list.

When a connection is made with a projector, a toolbar is displayed.

I

Set options

You can make general setting options such as the processing method when starting up EasyMP Network Projection. For details, see Set options s

p.42

J

Save in the profile

Saves the results of a search for projectors on the network as a Profile. s

p.37

K

Clear list

Deletes all search results.

L

IP address (Advanced Connection Mode only)

The projector's IP address is displayed.

M

Display

Select the number displayed (when Use multi-display is selected). s

p.32

N

Profile

You can search for a projector on the network using a Profile saved using Save in the profile. s

p.37

O

SSID (Quick Connection Mode only)

The projector's SSID is displayed.

P

Signal intensity (Quick Connection Mode only)

As the Signal intensity increases, so does the number of lit Indicators.

Q

Update list (Quick Connection Mode only)

Updates Status and Signal intensity.


Using the Toolbar

The toolbar is displayed on the computer screen after EasyMP Network

Projection starts and a connection is made with the projector. You can use this toolbar to operate and make settings for the projector.

Select target projector

Click to limit the projectors operated from the toolbar when projecting from multiple projectors using the distribution function or Multi-screen display. The indication below the icon shows the projectors that can be controlled.

ALL indicates that all of the connected projectors can be controlled.

For example, when "1, 3" is displayed, projectors No. 1 and

No. 3 can be controlled.

Click to display the following screen.

18

A

Select the projector to be controlled.

B

Indicates the No. of an allocated projector. This No. indicates the No. of the projector that you can control from the toolbar.

C

Indicates the status of the projector.

Stop

Stops projection while connected to the projector.


Show

Releases Stop or Pause.

Pause

Pauses projected images while connecting to the projector.

Presentation Mode

Each time this is clicked, Presentation Mode switches between enabled/disabled. s

p.22

Projector control

While the projector is connected to the network, the projector's Shutter, Switch PC source and Switch video source functions can be controlled from the toolbar.

Click to display the following toolbar.

19

4 A/V Mute

The same function as the [Shutter] button on the remote control. See your User’s Guide for more information.

5 Switch PC source

The Source alternates between Computer,

BNC, DVI-D and LAN each time you click.

6 Switch video source

The Source alternates between S-Video, Video and HDMI each time you click. The projector will not switch to the S-Video input if there is no cable connected to the port.


Screen Preview

Displays the multi-screen preview screen.

Click to display a preview with the settings you have made. Click the displays to enlarge each Screen Preview to full-screen.

Set options

Transmission performance during the transfer of computer images can be adjusted. s

p.42

Movie Sending Mode

Used to immediately play back a movie file.

Disconnect

Disconnects the connection to the projector.

Signal intensity

This is displayed when the connection is made in Quick

Connection Mode. As the Signal intensity increases, so does the number of lit indicators.

Switch Toolbar display

The toolbar display is switched as follows. The toolbar display remains as is until switched again.

Full

20

Normal

Simple

21

EasyMP Network Projection Useful Functions

This chapter explains those functions that may be useful in a meeting or presentation, such as the function which allows you to send images to multiple projectors from a single computer (Multi-Screen Display).

Projecting Only a PowerPoint Slide Show (Presentation Mode)

Projecting Only a PowerPoint Slide Show (Presentation Mode)

In Presentation Mode, the images are only displayed when performing a

PowerPoint Slide Show on a computer. When you stop Slide Show, the projector displays a black screen. This is useful when you only want to display the Slide Show.

In addition to PowerPoint, Keynote is compatible with Presentation

Mode for Macintosh.

Procedure

A

If necessary, select the projector you want to control. s

p.18

B

Click the button on the toolbar.

Presentation Mode begins.

C

Click the button again to exit Presentation Mode.

q When the [ ] button is pressed while projecting a PowerPoint slide show, the next slide is displayed. Press the [ ] button to display the previous slide.

22

Projecting Movies from a Computer (Movie Sending Mode)


In Movie Sending Mode, movie files can be sent directly to a projector.

As a result, a movie can be projected much more smoothly than when it is being sent from an application running on a PC.

q • Movie Sending Mode is valid for one projector only.

It is not possible to apply Movie Sending Mode to more than one projector.

• Depending on the communication method and the available reception, the image may skip or stall.

23

B

Select the projector you want to use to playback the movie and click "OK".

The Movie Sending Mode screen appears.

C

Click "Select file".

Supported File Types

The file types supported by Movie Sending Mode are listed in the following table.

File Type (Extension) Video Codec

.mpg

.mpeg

MPEG-2

.wmv

WMV8

WMV9

Recording Quality

Highest frame rate: 30 fps

Maximum resolution:

720×576

Files to which DRM (Digital Rights Management) is applied cannot be projected.

Playing Back a Movie

Procedure

A

Click the button on the toolbar.

The projector selection screen is displayed.


D

Select the movie file you want to play back and then click

"Open".

The Movie Sending Mode screen reappears. The selected files are displayed in the Movie file list.

If you perform Select file again, the Movie file list changes after you make your selection.

E

Play and stop the movie files from the Movie Sending Mode screen.

Play

Plays back the file.

Pause

Pauses play back.

Stop

Stops play back.

Back

Plays back from the beginning of the file that is playing.

Next

Plays back from the beginning of the next file.

Repeat

Repeatedly plays back the file list in order. When there are multiple files in the list, it is not possible to repeatedly play back only some of those files.

F

Click "Close" to end Movie Sending Mode.

24

Play Back Head

Drag & Drop to the point in the file where you want to start play back.

Using Multi-Screen Display

25


Multi-screen display mode allows you to project different images from multiple projectors that are connected to a single computer.

With Windows, multiple virtual display

g drivers can be set in the computer, and each image can be projected by the projector. This function is not

available with Windows Vista or Windows 7 due to restrictions in the specifications.

For Macintosh, an external monitor must be connected to the computer to enable the function. While the following explanation refers to virtual display, for Macintosh the operation relates to the screens displayed on the physically connected monitor.

A

Actual monitor image

B

Image of virtual display1

C

Image of virtual display2


Example of Adjusting the Virtual Display

By arranging the virtual display

g

allocation, you can project only the image that you want to show or project different images from left to right in a presentation.

Arrangement example 1

B Image of virtual display

Arrangement example 2

Excel file

26

A Actual monitor image

PowerPoint file

A Actual monitor image

B Image of virtual display

PowerPoint file presenter tools

Slide Show using a PowerPoint file


Procedure Before Using the Multi-screen Display

Function

1. Setting the Virtual Display s

p.27

In a Windows environment, enable the virtual display g

driver as necessary. And, for both Windows and Macintosh, set up the virtual display arrangement.

2. Allocating the image to be projected s

p.31

Open the file to be projected, and then move the screen to the virtual display according to the actual projection arrangement.

3. Projecting the allocated images s

p.32

Allocate a virtual display number to a projector that is connected through the network, and then start projection.

Setting the Virtual Display

This section explains the virtual display for arrangement example 1. s

p.26

Enable the virtual display driver (Windows only)

Enable the virtual display

g driver. Those users listed below do not have

to perform this operation and should skip to s "Adjusting the Virtual

Display" p.28

.

• Those users who have enabled virtual displays installing EasyMP

Network Projection.

• Those users with Macintosh computers.

27

Procedure

A

Start Windows on the computer, then select "Start" -

"Programs" (or "All Programs") - "EPSON Projector" -

"Add-Remove EPSON Virtual Display".

The Add-Remove EPSON Virtual Display screen is displayed.

B

Select the virtual display you want to use.

Up to four monitors can be added. In this example, a single virtual display is to be used. When setting multiple virtual displays, select as many displays as is necessary.

Any one of the displays can be selected.

C

Click "OK".

When you click OK, the drivers for the virtual display are enabled.

At this point, it is normal for the display to flicker. Wait for the

Add-Remove EPSON Virtual Display screen to close.


28

Adjusting the Virtual Display

After starting EasyMP Network Projection, the setup of the virtual displays varies between Windows and Macintosh. The procedures are explained separately below.

q Check the following points before starting EasyMP Network Projection when connecting via Wireless LAN. If the following points are not set correctly, Multi-screen display cannot be used.

• When you use Quick Connection Mode, the SSID for the computer and the projector must be the same.

• The Wireless LAN system for the computer and each projector must be the same.

You can modify the SSID and Wireless LAN system for the projector from the Network menu in the projector's Configuration menu. See your User’s

Guide for more information.

Procedure

For Windows

A

Select "Start" - "Programs" (or "All Programs") - "EPSON

Projector" - "EasyMP Network Projection" to start EasyMP

Network Projection.

B

If the Connection mode screen opens, select "Advanced





C

Select the "Use multi-display" check box.

Display layout and Display properties are added at the bottom of the screen.


D

Click "Display properties".

The "Display Properties" screen is displayed.

E

Click the "Settings" tab.

29

F

Drag the displayed monitor icon and place it where desired.

Here, the actual monitor (1) is placed on the left, while the virtual monitor (3) is placed on the right.

When the computer has multiple display output terminals, the numbers assigned to the virtual terminals will be sequential to those of the physical terminals.

q • When an external monitor is connected as a secondary monitor, the image for that screen cannot be projected.

• Depending on the hardware, the number of the secondary monitor may be other than "2". When the monitor icon is displayed on the screen, click the icon and confirm that the monitor type shown under "Display" is other than "secondary".


• For Screen Resolution settings, see the following. s

p.53

When the monitor icon is arranged, a virtual display is connected as the image like below.

1 3

G

Click the "OK" button. The Display Properties screen closes.

Next, allocate the images you want to project. s

p.31

For Macintosh

A

Start EasyMP Network Projection. Double-click the

Applications folder of the hard drive volume in which

EasyMP Network Projection is installed, and then double-click the EasyMP Network Projection icon.

B

If the Connection mode screen opens, select "Advanced





C

Select the "Use multi-display" check box.

Display layout and Display preferences are added at the bottom of the screen.

D

Click "Display preferences".

30

The display setting screen is displayed.


E

Click "Arrangement".

31

G

Drag the displayed monitor icon and place it where desired.

F

De-select "Mirror Displays".

H

Close the display setting screen.

Allocating the Image to be Projected


p.26

Procedure

A

Open the file to be projected.

Start the PowerPoint and Excel files.


B

Drag the window to the desired virtual display g monitor,

and allocate it where the image is to be projected.

Drag the Excel window to the right until it cannot be seen. As a result, the PowerPoint window appears on the actual monitor, while the Excel window appears on the virtual display on the right.

Projecting the Allocated Images


p.26

Procedure

A

Select the number of the virtual display

g

to allocate on the

"Display", and set which image to be projected from which projector.

32


B

Click "Connect".

The image allocated to each projector is projected.

33 tual display, you must do so while viewing the projected image.

To perform mouse-based operations on the virtual display, move the mouse pointer in the direction of the virtual display, such that the pointer appears on the virtual display.

C

To terminate multi-screen display, click "Disconnect" on the toolbar.

q • In a Windows environment, if the virtual display driver has been enabled such that the mouse pointer can be moved outside the limits of the screen, there may be occasions when you lose track of the location of the pointer.

When you are not using a virtual display, clear the check mark against the virtual display under Add-Remove EPSON Virtual Display, so that the mouse pointer cannot be moved outside the limits of the screen. To subsequently use multi-display again, place a check mark against the required display under Add-Remove EPSON Virtual Display.

To clear a check mark, see the following. s

p.27

• You can adjust each projector's color tone. See your User’s Guide for more information.

In a Windows environment, you cannot view the image being sent to a virtual display on the computer. To adjust the image on the vir-

Connecting to a Projector on a Different Sub-net

This chapter explains how to connect a computer to a projector on a different sub-net via a Wired LAN or a wireless LAN access point on an existing network system.

34

Connecting to a Projector on a Different Subnet

Connecting to a Projector on a Different Subnet

By default, this application only searches for projectors on the same subnet as the computer. Therefore, even if you perform a search for projectors on the network, ones on a different subnet will not be found.

You can, however, identify and connect to a projector on a different subnet as follows:

• In Advanced Connection Mode, specify either an IP address or

Projector Name and perform a search.

The IP Address can be input directly. Also, provided the Projector name to be connected has been registered on the DNS server, you can perform a search simply by inputting that Projector name. s

p.36

• In Quick Connection Mode, click "Manual Search" on the EasyMP

Network Projection projector selection screen. You can specify the

SSID. When there are a lot of projectors you can narrow the search field by using SSID.

• Performing a search based on a Profile

Once you have performed a search for a projector on a different subnet, you can save the search as a Profile with an easy-to-remember name, and then use that Profile whenever you subsequently want to search for a projector on a different subnet. s

p.37

q If a search fails to find a projector, the most likely causes are as follows.

Proceed as appropriate, depending on the cause of the failure.

• For both Windows and Macintosh

If there is no wireless LAN signal or if the signal is weak, check whether there is anything that could be interfering with the signal.

• When the optional Wireless 802.11a/b/g Module is installed in the projector, and the Macintosh is connected to a Wireless LAN

Check whether AirPort is set to On. Or, check whether an appropriate access point has been selected.

35

Searching by Specifying the IP Address and Projector name (For Advanced Connection Mode only)

Searching by Specifying the IP Address and Projector name (For Advanced Connection Mode only)

In the following explanations, unless otherwise noted, Windows screen shots are used.

You see a similar screen even when using Macintosh.

Procedure

A

Click "Manual search" on the EasyMP Network Projection projector selection screen.

36

B

Enter the IP address or the Projector name for the projector you want to connect to, and click "OK".

The search results are displayed on the EasyMP Network Projection projector selection screen.

Provided the target projector has been identified, select that projector, and then click Connect to establish a connection.

When you will always be using that projector, save the search as a

Profile, so that you do not have to specify the relevant details every time you perform a search. s

p.37

Performing a Search with a Profile


You can save a search for a frequently used projector as a Profile. A

Profile is a file containing all of the information pertaining to a given projector, such as the Projector name, its IP address, and SSID. By specifying the profile each time you perform a search, there is no need to enter the IP Address or Projector name. For example, by creating a group of Profiles for each place where a projector is setup and managing them with folders, the target projector can be found quickly.

Making a Profile

Profiles are made by saving search results.

For details on how to edit a previously saved Profile, see the following section. s

p.39

Procedure

A

When the projector is displayed on the EasyMP Network

Projection projector selection screen, click "Save in the profile".

37

A

Building A

B

Building B

C

Building C

D

Building D

E

F

G

Floor 1

Floor 2

Floor 3

This section explains how to create and edit a Profile.

The Save in the profile screen is displayed.


B

Enter a Profile name and then click "Add".

38

Projector information is registered in the Profile.

If you have previously saved a Profile, you are prompted to confirm whether it can be overwritten. To save a Profile with a different name, select Save as. If you have created a folder for a Profile, the following screens are displayed. After entering the Profile name and selecting the Save in destination, click Add.

For Windows q For details on how to create a folder for a Profile, see the following section. s

p.39

Searching by Specifying a Profile

You can search by specifying the Profile you created.

For Macintosh


39

Procedure

A

Click "Profile" on the EasyMP Network Projection projector selection screen.

If no Profile is registered, you cannot select Profile.

Managing a Profile

You can change the name and the hierarchical structure of the Profile.

Procedure

A

Click "Set options" on the EasyMP Network Projection main screen.

The Set options screen is displayed.

B

Click "Edit profile".

B

From the menu that is displayed, select the projector you want to connect to.

The search results are displayed on the EasyMP Network Projection projector selection screen.

Provided the target projector has been identified, select that projector, and then click Connect to establish a connection.

The Edit profile screen is displayed.


C

Edit the contents registered in the Profile.

A

B

Profile

Item

Profile

: Indicates a folder.

: Indicates a Profile.

Function

You can display the registered Profile. You can manage it by creating a folder. You can change the order of the Profile or the folder by dragging

& dropping.

40

Profile

Item

Copy

Function

You can copy the Profile. The copied Profile is saved in the same folder as the original with the same name.

You can delete the Profile and the folder.

Delete

Rename You can display the Rename dialog box and rename the folder or the Profile. You can enter up to 32 characters in the Rename dialog box.

Create folder You can create a new folder.

Export

Import

You can Export a Profile, as well as Import and use a Profile.

Used when you want to read and use an exported Profile.

Information on selected profile

Item Function

Projector name, IP address

You can display the projector information registered in the Profile.

Delete You can delete the information for the selected projector. When all projector information is deleted, the profile is also deleted.

D

Click "OK".

Saves your edits and closes the Edit profile screen.

Setting the EasyMP Network Projection Operation

You can make setting options such as the processing method when EasyMP Network Projection starts.

41

Using Set options

42


You can make setting options such as the processing method when

EasyMP Network Projection starts.

Import Set options from the EasyMP Network Projection main screen.

Procedure

A

Click "Set options" on the EasyMP Network Projection main screen.

Setting Each Item

Set each item from the General settings tab and the Adjust performance tab.

General settings tab

The Set options screen is displayed.

B

Set each of the items.

Confirm the details of the set items in the next step. When you have made all the necessary settings, click OK to close the Set options screen.

Use full-screen video transfer

Encrypt communications

Windows only (excluding Windows Vista and

Windows 7)

Select this check box when you want to display

Windows Media Player in full screen. However, clear this check box if the movie does not play back smoothly.

Select to Encrypt and transmit data. Even if data is intercepted, it cannot be decrypted.

When using Quick Connection Mode, make sure you always select this checkbox.


43

Display Connection Mode Selection window on startup

Search method on startup

Set whether or not the Quick Connection

Mode/Advanced Connection Mode screen is displayed when EasyMP Network Projection starts.

Clear this checkbox once you have settled on a regular startup method.

Select from the following projector search methods executed when EasyMP Network

Projection is started.

Automatic search on startup

Specify search method after startup

Search with the last network configuration

The Edit profile dialog box is displayed. s

p.39

Edit profile

Switch LAN Windows only

The Switch Network Adapter dialog box is displayed. This is used when it is necessary to switch the network adapter to be used for a search when a computer has multiple adapters.

By default, all of the network adapters are used to perform a search. When a Wired LAN is always used as the connection method, select a Wired LAN adapter.

Restore Defaults You can reset all adjustment values on the General settings tab to their default settings, except for Edit profile and Switch LAN.

Adjust performance tab

Performance adjustment slider

Transfer layered window

The performance can be set to Fast, Normal, and

Fine.

Set to Fast when movie projections are interrupted.

Windows only (excluding Windows Vista and

Windows 7)

Set whether or not to transfer a layered window.

The layered window is in use when contents such as messages displayed on the computer are not projected by the projector. Select this checkbox to project contents such as messages that use the layered window.

Clear this checkbox if you do not want the mouse pointer to flicker on the screen.

Restore Defaults You can reset all adjustment values for the Adjust performance tab functions to their default settings.

Using Set options q When you click on the toolbar, only the Adjust performance tab is displayed.

Audio Output tab

Because this projector does not support the audio sending function, settings on the Audio Output tab are disabled.

44

Using the Network Projector Function to Project Images

This chapter explains how to project the images from a computer by using Network Projector which is a standard application provided with Windows

Vista and Windows 7.

45

Using Network Projector

Using Network Projector

"Network Projector" is a standard function in Windows Vista and

Windows 7. You can project images from the computer by detecting the projector on the network through a function of the OS (without having to install any special software).

46

B

On the computer, start Windows, and then click "Start" - "All programs" - "Accessories" - "Connect to a Network

Projector".

The connection setting screen is displayed.

The projector is identified by inputting its IP address, or by allowing the OS to automatically identify all of the connected projectors.

C

Once the OS has identified all of the connected projectors, select the one that you want to use and click "Connect".

When the projector password screen is displayed, enter the Projector keyword shown in the LAN standby screen. s

p.14

q When using "Network Projector" from "Options" in Windows Meeting

Space , set the colors for the computer screen you are using to the highest level (32bit). If it is not capable of a 32bit display, a message is displayed and you cannot connect.

Via a network you can project by connecting one computer to one projector.

Compatible OS

Windows Vista: Home Premium/Business/Enterprise/Ultimate

Windows 7: Professional/Ultimate

This section provides an easy explanation of Network Projector.

Check that the projector and computer are connected to the network, and carry out the following operations.

Procedure

A

Turn the projector on, and then press the LAN button on the remote control.

Using a Computer to Set Up, Monitor and Control Projectors

This chapter explains how to use a computer that is connected to the network to change projector settings and to control the projector.

47

Changing Settings Using a Web Browser (Web Control)


You can set up and control the projector from a computer by using the

Web browser of a computer that is connected to the projector via a network. Setup and control operations can be performed remotely if this function is used. In addition, since you can use the computer's keyboard, entering characters required for setup is easier.

Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a Macintosh, you can also use Safari. If, however, you are using Safari under Mac OS X 10.2.8, some of the Web control radio buttons may not be displayed properly.

q If Communication On is set as the Standby Mode setting in the projector’s

Extended menu, setup and control with a Web browser are possible, even when the projector is in standby mode (when the power is off).

48

B

Enter the IP address of the projector in the address input box of the Web browser, and press the [Enter] key on the computer's keyboard.

Web Control is displayed.

When Web Control Password is set in the Network menu from the projector's Configuration Menu, enter the Password.

Projector Setup

You can set items that are usually set in the projector's Configuration

Menu. The contents set are reflected in the Configuration Menu. There are also items that can only be set in the Web browser.

Displaying Web Control

Use the following procedure to display Web Control.

q If your Web browser is set up to connect via a proxy server, Web Control cannot be displayed. To use Web Control, you need to make network connection settings with a device other than a proxy server.

Entering the IP address of the projector

Web Control can be opened by specifying the IP address of the projector as follows when using Advanced Connection Mode.

Procedure

A

Start the Web browser on the computer.

Items in the Configuration menu that cannot be set by the web browser

All items in the Configuration Menu can be set with the exception of the following items.

• Signal Menu - DVI/HDMI Video Range

• Settings Menu - Keystone - Quick Corner

• Settings Menu - Pointer Shape

• Settings Menu - Test Pattern

• Settings Menu - User Button

• Extended Menu - registering User's Logo

• Extended Menu - Operation - BNC Sync Termination

• Extended Menu - Language

• Extended Menu - Operation - High Altitude Mode

• Extended Menu - Operation - Shutter Timer


• Reset Menu - Reset All

Items that can only be set in the Web browser

The following items can only be set in a Web browser.

• SNMP Community Name

• Monitor Password

49

Using the Mail Notification Function to Report Problems

Using the Mail Notification Function to Report Problems

By setting the Mail Notification function from the projector's

Configuration Menu, notification messages will be sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors. See your User’s Guide for more information.

q • Up to a maximum of three notification destinations (Addresses) can be recorded, and notification messages can be sent to all three destinations at once.

• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.

• If Communication On is set as the Standby Mode setting in the projector’s

Extended menu, monitoring is possible even when the projector is in standby mode (when the power is off).

50

Management Using SNMP

Management Using SNMP

By setting SNMP from the projector's Configuration Menu, notification messages are sent to preset IP addresses when a problem or warning occurs with a projector. This is useful when controlling projectors collectively at a point distant from them. See your User’s Guide for more information.

q • SNMP should be managed by a network administrator or someone who is familiar with the network.

• To use the SNMP function to monitor the projector, you need to install the

SNMP manager program on your computer.

• The managing function using SNMP cannot be used via Wireless LAN in

Quick Connection Mode.

• Up to two destination IP addresses can be saved.

51

Appendix

52

Connection Limitations

53


When projecting computer images while running EasyMP Network

Projection, the following restrictions apply.

Supported Resolutions

The following computer screen resolutions can be projected. You cannot connect to a computer with a resolution greater than UXGA

g

.

• VGA

g

(640x480)

• SVGA g (800x600)

*

• XGA

g

(1024x768)

*

• SXGA g (1280x960)

• SXGA (1280x1024) *

• SXGA+ (1400x1050) *

• WXGA (1280x768)

• WXGA (1280x800)

• WXGA+ (1440x900)

• UXGA (1600x1200)

* Supported resolutions when multi-screen display function is on.

If a computer with a special screen size is used where the ratio of height and width is not represented, a screen resolution closest to the width is selected from the list of 10 above.

In this case, in wide screen the horizontal margins are projected, in narrow screen the empty vertical margins are black.

Display Color

The number of colors for computer screens that can be projected.

Windows

16-bit color

32-bit color

Macintosh

About 32,000 colors (16-bit)

About 16.7 million colors (32-bit)

The operational guarantee for multi-screen display is 16-bit and 32-bit color.

Number of Connections

You can connect up to four projectors to one computer and project simultaneously.

You cannot connect multiple computers to one projector simultaneously.

Others

• If the transmission speed of the Wireless LAN is low, the network might be cut off unexpectedly.

• When videos are played back, they do not play back as smoothly as when displayed on the computer.

• Applications that use part of DirectX functions may not be displayed correctly. (Windows only)

• Cannot project full screen MS-DOS prompts. (Windows only)

• There are times when the image on the computer screen and the image projected by the projector may not match exactly.


54

When Using Windows Vista and Windows 7

Note the following points when using EasyMP Network Projection with a computer running Windows Vista and Windows 7.

• A few minutes after you connect a computer to the projector over a network with EasyMP Network Projection, the following message is displayed.

It is recommended that you select Keep the current color scheme, and don't show this message again . This selection is enabled until the computer is restarted.

Limitations when projecting from Windows Photo Gallery

Note the following two limitations when launching Windows Photo

Gallery when EasyMP Network Projection is running.

• Slide Shows are played back in simple mode when projecting from

Windows Photo Gallery.

Because the toolbar is not displayed, you cannot make changes while playing a Theme (effects), regardless of the Windows Experience Index rating.

Once simple mode has started, you cannot change modes while

Windows Photo Gallery is running even if you close EasyMP Network

Projection. Restart Windows Photo Gallery.

• You cannot play movies.

Limitations in Windows Aero

Note the following two limitations when the window design for your computer is Windows Aero.

• The layered window is projected regardless of Transfer layered window setting in Set options in EasyMP Network Projection.

For example, when the Transfer layered window setting for the EasyMP

Network Projection toolbar is disabled, it is not projected even if it is displayed on the computer screen, however the toolbar is projected.

Limitations when projecting from Windows Media Center

You cannot project images in full screen display using Windows Media

Center. Switch to the window display mode to project the images.

Troubleshooting

Troubleshooting

If any of the following problems occur, refer to the pages given for each problem.

Problems concerning network functions

"Cannot connect using EasyMP Network Projection"

s

p.56

"When a connection is made using EasyMP Network Projection, the projected image remains as is, and a connection cannot be made from another computer."

s

p.56

"The projector is not found when EasyMP Network Projection is started."

s

p.56

"Cannot connect in Advanced Connection Mode or Wired LAN connection"

s

p.58

"The Slide Show cannot be displayed on the desired display when the multi-screen display function is being executed."

s

p.58

"Applications are no longer displayed from the computer screen when the multi-screen display function is executed."

s

p.58

"The mouse cursor is not displayed on the computer screen."

s

p.59

"When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear."

s

p.59

"When a connection is made using EasyMP Network Projection, a

PowerPoint Slide Show cannot be started."

s

p.59

"When a connection has been made using EasyMP Network Projection, the screen will not be refreshed when using an Office application."

s

p.60

"Error message when starting up EasyMP Network Projection"

s

p.60

"Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection."

s

p.61

Problems concerning monitoring and control

"Mail is not sent even if a problem occurs in the projector."

s

p.62

55

Troubleshooting

56

Problems Concerning Network Functions

Cannot connect using EasyMP Network Projection

Check the message on the screen and then apply the following countermeasures.

Error Messages

The application version used is not supported. Install the latest version of the application on your computer.

Remedy

Install the current version of EasyMP Network Projection from the EPSON Projector Software for

Meeting & Monitoring CD-ROM supplied with the projector.

When a connection is made using EasyMP Network Projection, the projected image remains as is, and a connection cannot be made from another computer.

Check

Did the presenter leave the conference room without cutting off the network connection?

Remedy

With EasyMP Network Projection, the connection with the computer that was previously connected can be cut off when another computer tries to connect with the projector, and it connects with the computer that is trying to connect.

Therefore, when a Projector keyword is not set for the projector, or if you know the Projector keyword, you can cut off the current connection and, if you perform a connection operation, you can connect to the projector.

When a Projector keyword is set for the projector, if you do not know the Projector keyword, restart the projector and reconnect.

The projector is not found when EasyMP Network Projection is started.

Check

Is the optional Wireless 802.11a/b/g Module connected?

For Wireless LAN

Remedy

Check that the optional Wireless 802.11a/b/g Module is securely connected.

Troubleshooting

57

Check

Is the Network Configuration screen from the

Configuration menu displayed on the projector?

Remedy

When the Network Configuration screen is displayed on the projector, network connection for

EasyMP Network Projection is disabled. Close network settings on the projector, and return to the

LAN standby screen.

Are the computer's LAN card and the built-in LAN function available?

Check that LAN is valid by checking Control Panel - System - Hardware in the device manager and so on.

Is the SSID the same as that of the access point?

Quick Connection Mode

Set an SSID that is different from that of the access point. See your User’s Guide for more information.

Is the DHCP function for Wired LAN turned On?


Was the network adapter used selected correctly with

EasyMP Network Projection?

Is the computer's Wireless LAN electromagnetic wave strength set to low?

Does the Wireless LAN conform to 802.11g, 802.11b, or

802.11a?

Is the firewall turned off, or has the firewall been registered as an exception?

Is the network cable connected correctly?

For Wired LAN

Turn Off the DHCP setting for Wired LAN from the Configuration Menu. See your User’s Guide for more information.

If the computer has multiple LAN environments, it cannot connect unless the network adapter is selected correctly. When using a computer running Windows, start EasyMP Network Projection, and select the network adapter you are using from Set options - Switch LAN. s

p.42

Enable the Wireless LAN.

For Wireless LAN connection, is the Wireless LAN setting enabled when the computer is in power save mode?

Are there any obstacles between the access point and the computer or projector?


Sometimes interference prevents the projector from being found in a search. Check for any obstacles between the access point and the computer or projector, and change their position to lessen potential interference.

Set the electromagnetic wave strength to maximum.

The optional Wireless 802.11a/b/g Module is only compatible with standards 802.11g, 802.11b, and

802.11a, and not with other standards such as 802.11.

When you do not wish to turn off the firewall or register the firewall as an exception, make the necessary settings to open the ports.

The ports used by EasyMP Network Projection are "3620", "3621", and "3629".

Check that the network cable is connected correctly. Reconnect it if it is not connected or not connected properly.

Troubleshooting

58

Cannot connect in Advanced Connection Mode or Wired LAN connection

Check

Are the SSID settings for the computer, access point, and projector different?

Are the WEP keys set properly?

Remedy

Set the computer, the access point, and the projector to the same SSID. See your User’s Guide for more information.

When selecting WEP from Security, set the access point, the computer, and the projector to the same

WEP key. See your User’s Guide for more information.

Are the connection denial functions, such as MAC

Address g restrictions and port restrictions, set correctly at

the access point?

Set the projector to allow connections from the access point.

Are the IP address, the Subnet Mask, and the Gateway

Address for the access point and the projector set correctly?

When not using a DHCP, adjust each setting. See your User’s Guide for more information.

Are the access point and the projector's subnet different? Select Manual search from EasyMP Network Projection, specify the IP address, and connect.

s

p.36

The Slide Show cannot be displayed on the desired display when the multi-screen display function is being executed.

Check

Are you using PowerPoint 2002 or an earlier version?

For Windows

Remedy

To set and use two or more virtual displays

g

, use PowerPoint 2003 or later, or limit the number of virtual displays to one before displaying the Slide Show.

Applications are no longer displayed from the computer screen when the multi-screen display function is executed.

Check

Is another application running on the virtual display

g

?

For Windows

Remedy

When EPSON Virtual Display is installed, another application sometimes runs on the virtual display. In this case, set EPSON Virtual Display to "Off" in "Screen properties".

Troubleshooting

59

The mouse cursor is not displayed on the computer screen.

Check

Is EPSON Virtual Display installed?

For Windows

Remedy

The mouse cursor was moved onto the virtual display

g

. When the virtual display checkbox is cleared on the Add-Remove EPSON Virtual Display screen, the mouse pointer returns to the screen display area.

When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear.

Check Remedy

Did you try to play back movies with Media Player or try to operate the screen saver preview?

Depending on the computer, the movie playback screen in Media Player may not be displayed, and the screen saver preview may not be displayed normally.

The display speed decreases when WEP encryption is enabled or multiple projectors are connected.

Is WEP encryption enabled, or are multiple projectors connected?

Have you enabled DHCP?

When DHCP is set to On in Advanced Connection Mode, if an available DHCP server is not found, it takes time to enter LAN standby status.

When a connection is made using EasyMP Network Projection, a PowerPoint Slide Show cannot be started.

Check Remedy

Was EasyMP Network Projection started while PowerPoint was running?

For Windows

When connecting with EasyMP Network Projection, make sure you close PowerPoint first. Slide Show might not run if connecting while PowerPoint is running.

Troubleshooting

60

When a connection has been made using EasyMP Network Projection, the screen will not be refreshed when using an

Office application.

Check

Is the mouse moved continuously?

Remedy

When you stop moving the mouse cursor, the screen is updated. If the screen does not update quickly, stop moving the mouse cursor.

Error message when starting up EasyMP Network Projection

Error Messages

Connection to the projector failed.

The keyword does not match. Re-enter the keyword displayed on the projector screen.

The selected projector is busy. Do you want to continue the connection process?

Remedy

Try to connect again. If it still does not connect, check the network settings on the computer and the network settings for the projector.

For details on the network settings to be made on the projector, see your User’s Guide.

Check the Projector keyword displayed on the LAN standby screen, and enter the Projector keyword.

EasyMP Network Projection initialization failed.

Connection failed due to keyword mismatch.

You tried to connect to a projector that is connected to another computer.

When the Yes button is clicked, it connects to the projector. The connection between the projector and the other computer is cut off.

When the No button is clicked, it does not connect to the projector.

The connection between the projector and the other computer is maintained.

Restart EasyMP Network Projection. If the message still appears, uninstall and then reinstall EasyMP

Network Projection.

s

p.8

When connecting to a projector for which a Projector keyword has been set, the wrong Projector keyword is entered.

Check the Projector keyword that is displayed on the projector's connection standby screen. After the connection is disconnected and then reconnected, enter the Projector keyword on the keyword entry screen that is displayed.

s

p.14

Troubleshooting

61

Error Messages

Network adapter information could not be obtained.

Remedy

Check the following:

Is a network adapter installed on the computer?

Is the driver for the network adapter used installed on the computer?

After checking, restart the computer and connect again.

If you still cannot connect, check the following:

Check the network settings on the computer and the network settings on the projector.


There is a PowerLite 735c projector in the connection destination. Change the computer screen resolution to SXGA (1280x1024) or less.

One or more connected projectors do not support resolutions greater than SXGA. Reduce the screen resolution and reconnect.

One or more projectors are not responding.

Enter the keyword displayed on the projector screen.

Cannot connect to the projector using this version of

EasyMP Network Connection. Install the latest version of

EasyMP Network Projection.

You cannot connect to multiple projectors simultaneously. Check the network settings on the computer and the network settings on the projector.


Check the Projector keyword displayed on the LAN standby screen, and enter the Projector keyword.

This message is displayed when connecting to the projector with EMP NS Connection. To connect, install the current version of EasyMP Network Projection from the EPSON Projector Software for

Meeting & Monitoring CD-ROM supplied with the projector.

Network settings are not restored after cutting the connection to the computer with EasyMP Network Projection.

Check

Are you manually connecting to a Wireless LAN when the computer starts up?


Try connecting to the Wireless LAN manually.

Remedy

Troubleshooting

62

Problems Concerning Monitoring and Control

Mail is not sent even if a problem occurs in the projector.

Check

Is the optional Wireless 802.11a/b/g Module connected?


Remedy

Check that the optional Wireless 802.11a/b/g Module is securely connected.

Is the network connect setting correct?

Is Standby Mode set to Communication On?

Check the projector's network settings. See your User’s Guide for more information.

To use the Mail Notification function when the projector is in standby, set Communication On in

Standby Mode from the Configuration Menu. See your User’s Guide for more information.

Did a fatal abnormality occur and the projector come to a sudden stop?

When the projector comes to a sudden stop, mail cannot be sent.

If, after checking the projector, the abnormal state continues, contact Epson. See your User’s Guide for more information.

Is power being supplied to the projector?

Is the network cable connected correctly?

For Wired LAN

Check that your electrical outlet or power source is functioning correctly.

Check that the network cable is connected correctly. Reconnect it if it is not connected or not connected properly.

Glossary

63

Glossary

This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.

MAC Address

SVGA

SXGA

UXGA

VGA

XGA

Ad hoc

Virtual Display

An abbreviation of Media Access Control. The MAC Address is an ID number unique to each network adapter. A unique number is assigned to each network adapter, and data is transmitted between network adapters based on this identification.

A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.

A type of video signal with a resolution of 1,280 (horizontal) ^ 1,024 (vertical) dots that is used by IBM PC/AT-compatible computers.

A type of video signal with a resolution of 1,600 (horizontal) ^ 1,200 (vertical) dots that is used by IBM PC/AT-compatible computers.

A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.

A type of video signal with a resolution of 1,024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.

A method of Wireless LAN connection that communicates with wireless LAN clients without using an access point. It is not possible to communicate with two or more devices simultaneously.

The screen for one computer is output to multiple displays. A large virtual screen can be created by using multiple displays.

General Notes

General Notes

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or

Epson Approved Products by Seiko Epson Corporation.

The contents of this guide may be changed or updated without further notice.

Illustrations in this guide and the actual projector may differ.

Trademarks

Epson and EasyMP are registered trademarks and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

64

PowerLite is a registered trademark of Epson America, Inc.

Macintosh and Mac are trademarks of Apple Inc.

Microsoft, Windows, Windows NT, Windows Vista, Windows 7, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

This product includes RSA® BSAFE™ Cryptographic software from RSA

Security Inc. RSA is a registered trademark of RSA Security Inc. BSAFE RSA

Security Inc. is a registered trade mark in the United States and other countries.

This product includes NetNucleus® WPA Cryptographic software from

TOSHIBA INFORMATION SYSTEMS CORPORATION. NetNucleus is a registered trademark of TOSHIBA INFORMATION SYSTEMS CORPORATION in Japan.

WPA™, WPA2™ and Wi-Fi Protected Setup™ are registered trademarks of

Wi-Fi Alliance.

Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

Software Copyright:

This product uses free software as well as software to which this company holds the rights.

The following is information on the free software used by this product.

General Notes

1. LGPL

(1) This company uses free software for this product under the terms of the GNU LESSER General Public License Version 2, June 1991

(henceforth "LGPL") or later versions.

You can see the full text of the LGPL on the following Web sites.

[LGPL] http://www.gnu.org/licenses/lgpl.html

This company, under the terms of the LGPL, discloses the source code for the free software used in this product based on the LGPL. Contact the support personnel as provided in the Epson Projector Contact list to reproduce, modify, and/or distribute the free software concerned.

Please follow the conditions of the LGPL when reproducing, modifying, and/or distributing the free software concerned. Also, the free software concerned is offered "as is" with no guarantee or warranty what so ever. The term guarantee includes, but is not limited to, appropriate commercialization, business potential, purpose of use, and does not infringe on third person rights

(including, but not limited to, patent rights, copyrights, and trade secrets).

(2) Furthermore, as stated in (1), there is no guarantee for free software that is included in this product to which the LGPL applies because of the characteristics of the free software that has already used in this product; any problems in this product (including problems that originate with the free software concerned) do not influence the conditions of the guarantee (written guarantee) issued by this company.

(3) Under the terms of the LGPL, the source code as well as authorship for the free software used in this product is disclosed as stated in (1).

2. Other free software

As well as the free software used under the terms of the LGPL, this company also uses the following free software for this product.

65

Hereafter, each author, the conditions, and so on are described in the original. Furthermore, there is no guarantee for free software because of the characteristics of the free software that has already been used in this product; any problems in this product (including problems that originate with the free software concerned) do not influence the conditions of the guarantee (written guarantee) issued by this company.

(1) libpng

CopyrightZ 1998-2004 Glenn Randers-Pehrson

CopyrightZ 1996-1997 Andreas Dilger

CopyrightZ 1995-1996 Guy Eric Schalnat, Group 42, Inc.

(2) zlib

CopyrightZ 1995-2003 Jean-loup Gailly and Mark Adler

Z SEIKO EPSON CORPORATION 2009. All rights reserved.

General Notes

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

Copyright© 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street,

Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software

Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

66

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary

GNU General Public License. This license, the GNU Lesser General Public

License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

General Notes

We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public

License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the

Library has the freedom and the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

67

General Notes

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR

COPYING, DISTRIBUTION AND MODIFICATION

0.

This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs

(which use some of those functions and data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".)

"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the

Library (independent of the use of the Library in a tool for writing it).

Whether that is true depends on what the Library does and what the program that uses the Library does.

68

1.

You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2.

You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

General Notes

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the

Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3.

You may opt to apply the terms of the ordinary GNU General Public

License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU

General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the

Library into a program that is not a library.

69

4.

You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of

Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5.

A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not.

Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

General Notes

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6.

As an exception to the Sections above, you may also combine or link a

"work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the

Library is used in it and that the Library and its use are covered by this

License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under

Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the

Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the

Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.

70 c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection

6a, above, for a charge no more than the cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7.

You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the

Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities.

This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.

General Notes

8.

You may not copy, modify, sublicense, link with, or distribute the

Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the

Library is void, and will automatically terminate your rights under this

License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9.

You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the

Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this

License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

71

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the

Free Software Foundation.

General Notes

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE

COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY

"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE

LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU

ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR

CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO

IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY

WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS

PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING

ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY

(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD

PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER

SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

72

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General

Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.

<one line to give the library's name and a brief idea of what it does.>

Copyright© <year> <name of author>

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or

(at your option) any later version.

This library is distributed in the hope that it will be useful, but

WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public

License along with this library; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary.

Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library

`Frob' (a library for tweaking knobs) written by James Random Hacker.

<signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice

That's all there is to it!

General Notes

For embedded multimedia software:

This product contains embedded multimedia software licensed from

Ingenient Technologies, Inc. ( http://www.ingenient.com

).

Copyright© 2000-2007 Ingenient Technologies, Inc. All rights reserved.

For MPEG-4 ASP:

With respect to a Licensee offering MPEG-4 Video Decoders and/or

Encoders the following notice shall be given: THIS PRODUCT IS

LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO

LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF

A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE

WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO")

AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED

BY A CONSUMER ENGAGED IN A PERSONAL AND

NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM

A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE

MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED

FOR ANY OTHER USE. ADDITIONAL INFORMATION

INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL

AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED

FROM MPEG LA,LLC. SEE HTTP://WWW.MPEGLA.COM.

For MPEG-4 AVC:

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT

PORTFOLIO LICENSE FOR THE PERSONAL AND

NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO

IN COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO")

AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A

CONSUMER ENGAGED IN A PERSONAL AND

NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM

A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO

LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER

USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM

MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM

For WMV/WMA (Microsoft):

This product is protected by certain intellectual property rights of

Microsoft.

Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.

CPD-27726R1

73

No results