advertisement
▼
Scroll to page 2
of 102
Copyright Copyright Earthlink is a registered trademark of EarthLink Network, Inc. Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Quicken®2000 is a registered trademark of Intuit, Inc. Fujitsu and the Fujitsu logo are registered trademarks and LifeBook is a trademark of Fujitsu Limited. PC-Doctor is a trademark of PC-Doctor.com, Inc. First Cabin is a service mark of Fujitsu PC Corporation. McAfee is a registered trademark of Network Associates/ McAfee.com, Inc. The following are registered trademarks of IBM Corporation: IBM, IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows. PCMCIA is a trademark of the Personal Computer Memory Card International Association. Sony MiniDisk is a trademark of Sony Electronics, Inc. Philips is a trademark of Koninklijke Philips Electronics N.V. Netscape Communicator is a registered trademark of Netscape Communications Corporation. LapLink is a registered trademark of LapLink.com, Inc. All other trademarks mentioned herein are the property of their respective owners. Adobe Acrobat Reader is a registered trademark of Adobe System Inc. © Copyright 2000 Fujitsu PC Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation. CompuServe and AOL are registered trademarks of America Online, Inc. FPC58-0397-01 Intel and Pentium are registered trademarks and SpeedStep is a trademark of Intel Corporation. DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu PC Corporation Address: 5200 Patrick Henry Drive Santa Clara, CA 95054 Telephone: (408) 982-9500 Declares that: LifeBook C Series Configuration: LifeBook C-6577 LifeBook C-6556 LifeBook C-6547 Complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation. LifeBook C Series CAUTION Changes or modifications not expressly approved by Fujitsu PC Corporation could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ■ ■ ■ ■ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet that is on a different circuit than the receiver. Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone Network Your Fujitsu LifeBook may be supplied with an internal modem which complies with Part 68 of the FCC rules. On this LifeBook is a label that contains the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment among other information. If requested, the user must provide their telephone company with the following information: 1. The telephone number to which the LifeBook is connected. 2. The Ringer Equivalence Number (REN) for this equipment. 3. That the equipment requires a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant. 4. The FCC Registration Number. This equipment is designed to be connected to the telephone network or premises wiring using a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant and a line cord between the modem and the telephone network with a minimum of 26AWG. The REN is used to determine the number of devices that you may connect to your telephone line and still have all of those devices ring when your number is called. Too many devices on one line may result in failure to ring in response to an incoming call. In most, but not all, areas the sum of the RENs of all of the devices should not exceed five (5). To be certain of the number of devices you may connect to your line, as determined by the RENs, contact your local telephone company. If this equipment causes harm to the telephone network, your telephone company may discontinue your service temporarily. If possible, they will notify you in advance. If advance notice is not practical they will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC. This fax modem also complies with fax branding requirements per FCC Part 68. Your telephone company will probably ask you to disconnect this equipment from the telephone network until the problem is corrected and you are sure that the equipment is not malfunctioning. This equipment may not be used on coin-operated telephones provided by your telephone company. Connection to party lines is subject to state tariffs. Contact your state’s public utility commission, public service commission or corporation commission for more information. This equipment includes automatic dialing capability. When programming and/or making test calls to emergency numbers: ■ ■ Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in off-peak hours, such as early morning or late evening. FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or applications: ■ ■ ■ ■ ■ ■ ■ ■ ■ All public or semipublic coin-operated or credit card telephones. Elevators, highways, tunnels (automobile, subway, railroad or pedestrian) where a person with impaired hearing might be isolated in an emergency. Places where telephones are specifically installed to alert emergency authorities such as fire, police or medical assistance personnel. Hospital rooms, residential health care facilities, convalescent homes and prisons. Workstations for the hearing impaired. Hotel, motel or apartment lobbies. Stores where telephones are used by patrons to order merchandise. Public transportation terminals where telephones are used to call taxis or to reserve lodging or rental cars. In hotel and motel rooms as at least ten percent of the rooms must contain hearing aid compatible telephones or jacks for plug-in hearing aid compatible telephones which will be provided to hearing impaired customers on request. Copyright DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada. Notice to Users of the Canadian Telephone Network The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction. Fujitsu LifeBook computers are supplied with an internal modem which complies with the Industry Canada certification standards for telecommunication network protection and safety requirements. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu™ PC Corporation or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line. The connecting arrangement code for this equipment is CA11A. The Load Number is 0.3. The Load Number assigned to each telephone terminal device denotes the percentage of the total load to be connected to a telephone loop or circuit which is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices such that the total of the load numbers of all devices does not exceed 100. CAUTION For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas. Avis Aux Utilisateurs Du Réseau Téléphonique Canadien L’étiquette canadienne Industrie Canada identifie l’équipement certifié. Cette certification signifie que l’équipement satisfait certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Le département ne garantit pas le fonctionnement de l’équipement à la satisfaction de l’utilisateur. La série LifeBookTM E possède un modem interne conforme aux normes de certification d’Industrie Canada pour protéger les réseaux de télécommunications et satisfaire aux normes de sécurité. Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service. Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu PC Corp., ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique. Le code d’arrangement de connexion de cet équipement est CA11A. Le numéro de charge est 0.3. Le numéro de charge assigné à chaque terminal téléphonique indique le pourcentage de la charge totale pouvant être connecté à une boucle ou à un circuit téléphonique, utilisé par ce périphérique afin de prévenir toute surcharge. La terminaison d’une boucle peut être constituée de n’importe quelle combinaison de périphériques de sorte que le total de numéros de charge de tous les périphériques n’excède pas 100. AV E R T I S S E M E N T Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales. LifeBook C Series UL Notice This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 16 Vdc, with a current of 3.36 A. AC Adapter output polarity: + The modem-to-telephone network connection must be a line cord using a minimum #26 AWG wire. For Authorized Repair Technicians Only CAUTION For continued protection against risk of fire, replace only with the same type and rating fuse. CAUTION Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction. Ta b l e o f C o n t e n t s Fujitsu C Series LifeBook Table of Contents 1 PREFACE Preface About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . 3 Fujitsu PC Contact Information . . . . . . . . . . . . . . 3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 GETTING TO KNOW YOUR LIFEBOOK Overview Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 LifeBook Features. . . . . . . . . . . . . . . . . . . . . . . . . 8 LifeBook Software . . . . . . . . . . . . . . . . . . . . . . . . 8 Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . 8 Locating the Controls and Connectors Top and Front Components . . . . . . . . . . . . . . . . . 9 Left-Side Panel Components . . . . . . . . . . . . . . . 11 Right-Side Panel Components . . . . . . . . . . . . . . 12 BACK Panel Components . . . . . . . . . . . . . . . . . . 13 Bottom Components . . . . . . . . . . . . . . . . . . . . . 15 CoolView Display Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 16 CD Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 CD Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Volume Level Indicator. . . . . . . . . . . . . . . . . . . . 16 Suspend/Resume Indicator. . . . . . . . . . . . . . . . . 16 AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . 17 Battery Level Indicators . . . . . . . . . . . . . . . . . . . 17 Battery Charging Indicators. . . . . . . . . . . . . . . . 17 DVD Drive Access Indicator . . . . . . . . . . . . . . . 17 Hard Drive Access Indicator . . . . . . . . . . . . . . . 18 Floppy Disk Drive Access Indicator . . . . . . . . . . 18 PC Card Access Indicators . . . . . . . . . . . . . . . . . 18 NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . 18 CapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . 18 ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 18 Keyboard Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . 19 Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . 19 Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Touchpad Pointing Device Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . 21 Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Scrolling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Touchpad Control Adjustment . . . . . . . . . . . . . . 22 Volume Control Controlling the Volume . . . . . . . . . . . . . . . . . . . 23 Setting the Hardware Volume Control . . . . . . . . 23 LifeBook Application Panel Selector Switch . . . . . . . . . . . . . . . . . . . . . . . . . 24 Application Launch CD Player Buttons . . . . . . . . 24 CoolView Display. . . . . . . . . . . . . . . . . . . . . . . . 24 Configuring your LifeBook Application Panel . . . 24 Using the CD Player. . . . . . . . . . . . . . . . . . . . . . 25 Desktop Control Panel . . . . . . . . . . . . . . . . . . . . 26 ! LifeBook C Series Pre-Installed Software Learning About Your Applications . . . . . . . . . . . 28 PC-Doctor for Windows. . . . . . . . . . . . . . . . . . . 28 LapLink 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Quicken 2000 Basic . . . . . . . . . . . . . . . . . . . . . . 28 McAfee.com ActiveShield. . . . . . . . . . . . . . . . . . 28 McAfee.com Clinic (On-Line Coupon) . . . . . . . . 28 PMSet 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Adobe Acrobat Reader . . . . . . . . . . . . . . . . . . . . 28 Intel Speedstep. . . . . . . . . . . . . . . . . . . . . . . . . . 28 LifeBook Application Panel Software . . . . . . . . . 28 3 GETTING STARTED Power Sources Connecting the Power Adapters. . . . . . . . . . . . . 31 Display Panel 4 USER INSTALLABLE FEATURES Lithium ion Battery Recharging the Batteries . . . . . . . . . . . . . . . . . . 41 Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 42 Floppy Disk Drive Loading a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Preparing a Disk for Use . . . . . . . . . . . . . . . . . . 43 DVD Drive DVD Player Software . . . . . . . . . . . . . . . . . . . . . 44 Loading a DVD/CD . . . . . . . . . . . . . . . . . . . . . . 45 Removing a DVD/CD . . . . . . . . . . . . . . . . . . . . 45 Using the DVD Player Software . . . . . . . . . . . . . 45 Using the DVD Player on Battery Power . . . . . . 46 Auto Insert Notification Function . . . . . . . . . . . . 46 Opening the Display Panel . . . . . . . . . . . . . . . . . 32 Adjusting Display Panel Brightness . . . . . . . . . . . 32 Closing the Display Panel . . . . . . . . . . . . . . . . . . 32 PC Cards Starting Your LifeBook Memory Upgrade Module Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . 33 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 33 Booting the System with Windows 98 Second Edition . . . . . . . . . . . . . . . 34 Registering Your LifeBook . . . . . . . . . . . . . . . . . 35 Power Management Suspend/Resume Button . . . . . . . . . . . . . . . . . . 36 Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Hibernation (Save-to-Disk) Feature . . . . . . . . . . 36 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 37 Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 37 Windows 98 Second Edition Power Management. . . . . . . . . . . . . . . . . . . . . . 37 Restarting the System. . . . . . . . . . . . . . . . . . . . . 37 Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Installing PC Cards. . . . . . . . . . . . . . . . . . . . . . . 47 Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 48 Installing a Memory Upgrade Module . . . . . . . . 49 Removing a Memory Upgrade Module . . . . . . . 50 Checking the Computer Recognition of New Memory Capacity . . . . . . . . . . . . . . . . . 50 Device Ports Modem (RJ-11) Telephone Jack. . . . . . . . . . . . . 51 Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Universal Serial Bus Port. . . . . . . . . . . . . . . . . . . 51 1394 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Wireless Infrared (IR) Mouse Receiver . . . . . . . . 52 Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 52 Stereo Line-In Jack. . . . . . . . . . . . . . . . . . . . . . . 52 Digital Audio-Out Connector . . . . . . . . . . . . . . . 52 " Ta b l e o f C o n t e n t s S-Video Out Port . . . . . . . . . . . . . . . . . . . . . . . . 53 Headphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . 53 External Monitor Port. . . . . . . . . . . . . . . . . . . . . 53 7 5 Specifications TROUBLESHOOTING Troubleshooting Identifying the Problem . . . . . . . . . . . . . . . . . . . 57 Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 57 Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 58 Power On Self Test Messages . . . . . . . . . . . . . . 67 Emergency DVD Tray Release . . . . . . . . . . . . . . 69 Modem Result Codes . . . . . . . . . . . . . . . . . . . . . 69 Recovery CD-ROM . . . . . . . . . . . . . . . . . . . . . . 69 6 CARE AND MAINTENANCE Care and Maintenance Fujitsu LifeBook . . . . . . . . . . . . . . . . . . . . . . . . . 73 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Floppy Disks and Drives . . . . . . . . . . . . . . . . . . . 74 DVDs and CDs . . . . . . . . . . . . . . . . . . . . . . . . . . 75 PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 SPECIFICATIONS Configuration Label . . . . . . . . . . . . . . . . . . . . . . 79 Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . 80 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Mass Storage Device Options . . . . . . . . . . . . . . 80 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Device Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Dimensions and Weight . . . . . . . . . . . . . . . . . . . 81 Environmental Requirements . . . . . . . . . . . . . . . 81 8 GLOSSARY Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 LifeBook C Series 1 Preface 1 LifeBook C Series 2 Preface Preface ABOUT THIS GUIDE The LifeBook™ C Series from Fujitsu PC Corporation is a powerful notebook computer. It is powered by an Intel® Pentium® III microprocessor, has a built-in color display, a number of possible configurations, and brings the computing power of desktop personal computers (PCs) to a portable environment. This manual explains how to operate your Fujitsu LifeBook’s hardware and built-in system software. Your LifeBook is compatible with the IBM® PC AT. FUJITSU PC CONTACT INFORMATION Service and Support You can contact Fujitsu Service and Support in the following ways: ■ ■ ■ ■ Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution: ■ Your LifeBook comes with Microsoft® Windows® 98 Second Edition pre-installed. The Fujitsu LifeBook is a completely self-contained unit with an active-matrix (TFT) color LCD display. It has a powerful interface that enables it to support a variety of optional features. ■ ■ ■ ■ ■ ■ ■ Conventions Used in the Guide Keyboard keys appear in brackets. Example: [FN], [F1], [ESC], [ENTER] and [CTRL]. Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.) On screen buttons or menu items appear in bold Example: Click OK to restart your LifeBook. DOS commands you enter appear in Courier type. Example: Shut down the computer? Toll free: 1-800-8FUJITSU (1-800-838-5487) Fax: 1-901-259-5700 E-mail: [email protected] Web site: http://www.8fujitsu.com Product name Product configuration number Product serial number Purchase date Conditions under which the problem occurred Any error messages that have occurred Hardware configuration Type of device connected, if any Fujitsu On-line You can go directly to the on-line Fujitsu Product catalog for your LifeBook by clicking on the LifeBook Accessories Web site URL link, located in the Windows Start menu. You can also reach Fujitsu Service and Support on-line by clicking on the Fujitsu Service and Support Web site URL link, located in the Service and Support Software folder of the Windows Start menu. POINT POINT The point icon highlights information that will enhance your understanding of the subject material. CAUTION The caution icon highlights information that is important to your safety, to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully. You must have an active internet connection to use the on-line URL links. WARRANTY Your LifeBook is backed by a one year International Limited Warranty and includes toll-free technical support. Check the service kit that came with your LifeBook for warranty terms and conditions. WARNING The warning icon highlights information that can be hazardous to either you, your LifeBook, or your files. Please read all warning information carefully. 3 Li f eBook C Ser ies – Secti on One 4 2 Getting to Know Your LifeBook 5 ! LifeBook C Series – Section Two 6 " Overview Figure 2-1 Fujitsu C Series LifeBook Overview This section describes the components of your Fujitsu LifeBook. We strongly recommend that you read it before using your LifeBook – even if you are already familiar with notebook computers. UNPACKING When you receive your LifeBook, unpack it carefully, and compare the parts you have received with the items listed below. For a Pre-configured model you should have: ■ LifeBook C Series from Fujitsu (Figure 2-1) ■ Lithium ion battery, pre-installed ■ AC adapter with AC power cord (Figure 2-2) ■ Phone/Modem (RJ-11) telephone cable ■ Recovery CD ■ Driver and Application Restore CD ■ Getting Started Guide ■ ■ ■ ■ ■ User’s Guide Product Registration card International Limited Warranty Brochure Getting Started with Microsoft Windows 98 Second Edition Manual First Cabin Registration card and envelope Once you have checked and confirmed that your LifeBook system is complete, read through the following pages to learn about all of your LifeBook’s components. Figure 2-2 AC Adapter 7 LifeBook C Series – Section Two LIFEBOOK FEATURES ■ The LifeBook C Series is a compact, yet powerful notebook computer available with a variety of features, including: (See Specifications on page 79 for more information) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Latest high-speed Intel Pentium III mobile processors with SpeedStep technology 100 MHz SDRAM system memory Clear, bright XGA TFT display Lithium ion battery Built-in 20GB, 15GB or 12GB hard drive ATI Mobility-P video, 8MB of video RAM External monitor support with simultaneous display capabilities Dual monitor support LifeBook Application Panel/Audio CD Player Internal 56K fax/data/voice modem with V.90 support 8x DVD drive Full audio and video features: ■ 64 voice wavetable ■ Zoomed Video support for full motion video acceleration ■ Built-in Pioneer bass reflex stereo speakers ■ Stereo line-in jack ■ Stereo headphone jack ■ Microphone jack ■ Digital audio out Combination PC card slot accommodates two Type II or one Type III cards Fast IrDA (4Mbps) compatible infrared port for wireless data transfer Integrated pointing device for superb cursor control and comfort Full-size 87-key keyboard with three dedicated Windows keys Hot-swappable PS/2 port for external components USB device support Wireless infrared mouse support LIFEBOOK SOFTWARE ■ ■ ■ ■ ■ ■ ■ 8 Microsoft Windows 98 Second Edition operating system Microsoft Internet Explorer Microsoft Press Interactive Training for Windows 98 Microsoft Works 2000 Quicken 2000 LapLink 2000 PC-Doctor for Windows ■ PMSet 98 McAfee.com ActiveShield McAfee.com Clinic on-line coupon Adobe Acrobat Reader Netscape Communicator Internet Service Providers: ■ AOL ■ CompuServe™ ■ Earthlink DVD Player software POINT Some software may come separately on a CD and will have to be installed. POPULAR ACCESSORIES For ordering or additional information on Fujitsu accessories please visit our Web site at www.fujitsupc.com or call 1-877-FPCDirect. Memory Upgrades ■ 32MB SDRAM ■ 64MB SDRAM ■ 128MB SDRAM Expansions ■ Universal LAN Hub Power ■ Lithium ion battery ■ Auto/Airline Adapter ■ AC Adapter Additional Accessories ■ Wireless Infrared Mouse ■ Wireless Keyboard and Mouse ■ Numeric Keypad ■ USB Digital Camera (external) ■ Presentation Audio System ■ MindPath PocketPoint ■ TeleAdapt 16’ TeleCord ■ Notebook Guardian Lock ■ IBM Modem Saver Carrying Cases ■ Diplomat ■ Diplomat with Airpro ■ ProPack Backpack # Locating the Controls and Connectors Display Panel Display Panel Latch Closed Cover Switch TouchPad Scroll Button Wireless IR Mouse Receiver Suspend/Resume Button Stereo Speakers Stereo Speakers LifeBook Application Panel (including CoolView Display) Keyboard Figure 2-3 LifeBook with display open Locating the Controls and Connectors your unit is on or has been shut down from Windows. (See LifeBook Application Panel on page 24 for more information) The following is a brief description of your LifeBook’s top and front components. CoolView Display The CoolView Display presents symbols that correspond to specific components of your LifeBook. (See CoolView Display on page 16 for more information) Display Panel Latch The display panel latch locks and releases the display panel. Wireless IR Mouse Receiver The wireless IR mouse receiver allows the use of an optional wireless IR mouse. Display Panel The display panel is a color LCD panel with back lighting for the display of text and graphics. (See Display Panel on page 32 for more information) Suspend/Resume Button The Suspend/Resume button allows you to suspend LifeBook activity without powering off, resume your LifeBook from suspend mode, and power on your LifeBook when it has been shut down from Windows 98 Second Edition. (See Suspend/Resume Button on page 36 for more information) TOP AND FRONT COMPONENTS LifeBook Application Panel The LifeBook Application Panel allows you to either launch your favorite applications by the touch of a button or to use as an Audio CD-ROM player when 9 LifeBook C Series – Section Two Stereo Speakers The built-in dual speakers allow for stereo sound. Closed Cover Switch The closed cover switch turns off the LCD back lighting when the display panel is closed. Keyboard A full-size keyboard with dedicated Windows keys. (See Keyboard on page 19 for more information) Touchpad Pointing Device The Touchpad pointing device is a mouse-like cursor control with three buttons (left and right buttons, and scroll button). (See Touchpad Pointing Device on page 19 for more information) 10 Locating the Controls and Connectors Power Switch PC Card Slot PC Card Eject Buttons Lithium ion Battery Bay Figure 2-4 LifeBook left-side panel LEFT-SIDE PANEL COMPONENTS The following is a brief description of your LifeBook’s left-side components. Power Switch This switch is the main power switch for your LifeBook. Lithium ion Battery Bay The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery.(See Lithium ion Battery on page 41 for more information) PC Card Slots The PC Card Slots allow you to install two Type II PC Cards or one Type III PC Card. (See PC Cards on page 47 for more information) 11 LifeBook C Series – Section Two Volume Control Headphone Jack Microphone Jack DVD Eject Button Stereo Line-in Jack and Digital Audio-Out SPDIF Floppy Disk Drive DVD Drive Emergency DVD Tray Release Figure 2-5 LifeBook right-side panel RIGHT-SIDE PANEL COMPONENTS The following is a brief description of your LifeBook’s right-side components. Headphone Jack The headphone jack allows you to connect headphones or powered external speakers. (See Headphone Jack on page 53 for more information) Stereo Line-in Jack The stereo line-in jack allows you to connect an external audio source. (See Stereo Line-In Jack on page 52 for more information) Digital Audio-Out The digital audio-out jack allows you to download digital audio onto Sony™ & Philips Mini-disc player’s SPDIF (Sony Philips Digital Interface) format. (See Digital Audio-Out Connector on page 52 for more information) Microphone Jack The microphone jack allows you to connect an external mono microphone. (See Microphone Jack on page 52 for more information) 12 Volume Control The volume control provides manual control of the sound level of all audio output. (See Volume Control on page 23 for more information) DVD Drive The DVD drive allows you to play DVDs and CD-ROMs on your LifeBook. (See DVD Drive on page 44 for more information) DVD Eject Button The DVD Eject button is used to open the DVD tray. (See DVD Drive on page 44 for more information) Emergency DVD Tray Release The Emergency CD Tray Release provides a way to open the CD tray when power is not available to the system. (See Emergency DVD Tray Release on page 71 for more information) Floppy Disk Drive The floppy disk drive provides removable data storage. (See Floppy Disk Drive on page 43 for more information) Locating the Controls and Connectors Anti-theft Lock Slot PS/2 Port Parallel Port 1394 Port USB Port RJ-11 Modem Jack S-Video Port DC Power Jack External Display Port Infrared Port Serial Port Figure 2-6 LifeBook back panel BACK PANEL COMPONENTS The following is a brief description of your LifeBook’s back panel components. Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device. PS/2 Port The PS/2 port allows you to connect an external PS/2 keyboard, mouse or numeric keypad. (See PS/2 Port on page 51 for more information) Serial Port The serial port allows you to connect serial (RS-232C) devices. (This is also sometimes referred to as a COMM port.) (See Serial Port on page 51 for more information) External Display Port The external monitor port allows you to connect an external monitor. (See External Monitor Port on page 53 for more information) Infrared Port The fast IrDA compatible port allows you to communicate with another IrDA compatible infrared device without a cable. (See Infrared Port on page 52 for more information) Modem (RJ-11) Telephone Jack The Modem (RJ-11) telephone jack is for attaching a telephone line to the internal 56K modem. (See Modem (RJ-11) Telephone Jack on page 51 for more information) CAUTION Parallel Port The parallel port allows you to connect parallel devices. (This is also sometimes referred to as an LPT port.) (See Parallel Port on page 51 for more information) 1394 Port The 1394 port is used to connect between your LifeBook and a peripheral such as a digital video camera.(See 1394 Port on page 51 for more information) S-Video Port The S-Video output is used to transmit the S-Video signal. (See S-Video Out Port on page 53 for more information) The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload. CAUTION The internal modems on all Fujitsu LifeBooks from Fujitsu PC Corporation are certified for use in the United States and Canada. The modem may be certified in other countries. 13 LifeBook C Series – Section Two WARNING The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. USB Port The USB port allows you to connect Universal Serial Bus devices. (See Universal Serial Bus Port on page 51 for more information) 14 DC Power Jack The DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your LifeBook and charge the internal Lithium ion battery. Locating the Controls and Connectors Lithium ion Battery Bay Certificate of Authenticity Label (approximate location) Main Unit and Configuration Label Expansion RAM Slot Figure 2-7 LifeBook bottom panel BOTTOM COMPONENTS The following is a brief description of your LifeBook’s bottom panel components. Main Unit and Configuration Label The configuration label shows the model number and other information about your LifeBook. In addition, the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative. It identifies the exact version of various components of your LifeBook. (See Configuration Label on page 79 for more information) Lithium ion Battery Bay The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. (See Lithium ion Battery on page 41 for more information) Expansion RAM Slot The expansion RAM slot allows you to add optional memory upgrades. (See Installing a Memory Upgrade Module on page 49 for more information) 15 ! LifeBook C Series – Section Two CD Mark Mode Volume Level CD Track NumLock Floppy Disk Drive Access Message Display Scroll Lock Hard Disk Drive Access Application TRACK Lock CD Player VOL Suspend/ Resume State 1 1 Battery Installed Battery Charge AC Adapter Battery Level DVD Access 2 11 PC Card Access A A Caps Lock Figure 2-8 CoolView Display CoolView Display The CoolView Display is located at the front of your LifeBook, just below the touch pad. Within this display are symbols that correspond to specific components of your Fujitsu LifeBook. These symbols tell you how each of those components are operating. (Figure 2-8) MODE INDICATOR ■ ■ VOLUME LEVEL INDICATOR The Volume indicator displays the current volume of the DVD Player. The Mode indicator displays the current mode, as determined by the position of the selector switch. CD MARK The CD Mark indicator revolves when an audio CD is being played back, when the LifeBook is in standby mode. SUSPEND/RESUME INDICATOR The Suspend/Resume indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your LifeBook is in at that time. ■ ■ CD TRACK The CD Track indicator displays the number of the track being played. 16 Numerals indicate the track currently being played; when the player is in the stopped state, the number displayed is the first track on the disk. Dashes appear when no audio CD is set or when the CD is being read. ■ On: This means that there is power to your LifeBook and that it is ready for use. Flashing: This means that your LifeBook is in Suspend mode. Off: This means that your system is either in Hibernation (Save-to-Disk) mode, or that your LifeBook has been turned off with the power switch. " CoolView Display CAUTION POINT Your LifeBook’s power switch must be turned off to prevent all current draw. If there is no battery activity, the adapters are not connected, and the power switch is Off; the Battery Level indicators will also be off. AC ADAPTER INDICATOR The AC Adapter indicator states whether your LifeBook is operating from the AC adapter, the Auto/Airline adapter or the batteries. This icon has two different states that can tell you what power source your LifeBook is using. ■ ■ On: This means that either of the adapters are currently in use. Off: Power is only coming from the batteries, and you do not have an adapter connected. If you are charging your battery, the Power indicator symbol will remain on, even if your LifeBook is shut off. The Power indicator symbol will also remain on if you have an adapter connected and are shut down from Windows, but have not turned off the power switch. CAUTION A shorted battery is damaged and must be replaced. BATTERY CHARGING INDICATORS Located to the left of the Battery Level indicators is a small arrow symbol. This symbol states whether the battery is charging. This indicator operates whether the power switch is in the On or Off position, and will flash if the battery is too hot or cold to charge. (Figure 2-9) CAUTION Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged. BATTERY LEVEL INDICATORS The Battery Level indicators state whether or not the primary Lithium ion battery is installed. In addition, this symbol states how much charge is available within the battery. The symbol will only be displayed for a battery that is currently installed in your LifeBook. (Figure 2-9) 76%–100% Charging DVD DRIVE ACCESS INDICATOR The DVD Drive Access indicator tells you that the DVD drive is being accessed. If the Auto Insert Notification function is active, the indicator will flash periodically when your system is checking the DVD drive. If the Auto Insert Notification function is not active, the indicator will only flash when you access the DVD drive. The default setting is the Auto Insert Notification function active. (See Auto Insert Notification Function on page 46 for more information) 76%–100% 51%–75% 26%–50% 11%–25% Low Warning <11% Critical Low or Dead Battery POINT The Windows 98 Second Edition DVD Auto Insert Notification function will periodically check for a DVD installed in the drive, causing the DVD Access indicator to flash. The DVD automatic insertion function allows your system to automatically start a DVD as soon as it is inserted in the drive and the tray is closed. It will begin playing an audio DVD/CD or will start an application if the DVD/CD has an auto-run file.(See Auto Insert Noti- fication Function on page 46 for more information) Shorted Battery Figure 2-9 Battery Charge Status 17 LifeBook C Series – Section Two HARD DRIVE ACCESS INDICATOR The Hard Drive Access indicator states whether your internal hard drive or optional second hard drive is being accessed. NUMLK INDICATOR The NumLk indicator states that the internal keyboard is set in ten-key numeric keypad mode. POINT FLOPPY DISK DRIVE ACCESS INDICATOR The Floppy Disk Drive Access indicator states whether the floppy disk drive is being accessed. This indicator will flash if your software tries to access a disk even if no floppy disk drive is installed. (See Floppy Disk Drive on page 43 for more information) PC CARD ACCESS INDICATORS The PC Card Access indicator(s) state whether or not your LifeBook is accessing a PC Card(s). The indicator will flash if your software tries to access a PC Card even if there is no card installed. The number inside the indicator refers to which PC Card slot is being accessed. (See PC Cards on page 47 for more information) 18 If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys. CAPSLOCK INDICATOR The CapsLock indicator states that your keyboard is set to type in all capital letters. SCRLK INDICATOR The ScrLk indicator states that your scroll lock is active. # Keyboard Function Keys Fn Key Start Key Numeric Keypad Start Key Application Key Cursor Keys Figure 2-10 Keyboard Keyboard POINT USING THE KEYBOARD Your Fujitsu LifeBook has an integral 87-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. ■ Numeric keypad ■ Cursor keys ■ Function keys ■ Windows keys NUMERIC KEYPAD Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions. If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys. WINDOWS KEYS Your LifeBook has three Windows keys, consisting of two Start keys and an Application key. The two Start keys display the Start menu. This button functions the same as your on-screen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.) CURSOR KEYS The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right). 19 LifeBook C Series – Section Two FUNCTION KEYS Your LifeBook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. The [FN] key provides extended functions for the LifeBook and is always used in conjunction with another key. ■ [FN+F5]: Pressing [F5] while holding [FN] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less 20 than 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.) ■ [FN+F6]: Pressing [F6] repeatedly while holding [FN] will lower the brightness of your display. ■ [FN+F7]: Pressing [F7] repeatedly while holding [FN] will increase the brightness of the display. ■ [FN+F10]: Pressing [F10] while holding [FN] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel and external monitor or external monitor only. To u ch p a d P o i n t i n g D e v ic e Scrolling Button Touchpad Right Button Left Button Figure 2-11 Touchpad pointing device Touchpad Pointing Device The Touchpad pointing device comes built into your Fujitsu LifeBook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left and right button, and a scrolling button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. The scrolling button allows you to navigate quickly through pages, without having to use the scroll bars. (Figure 2-11) POINT An external mouse can be connected to either the USB or PS/2 port on your LifeBook or port replicator, and used simultaneously with the Touchpad. However, if you boot the system with an external mouse connected the Touchpad will be disabled or enabled depending on the specifications in your BIOS settings. (See BIOS Figure 2-12 Clicking DOUBLE-CLICKING Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and then immediately release it. You also have the option to perform the double-click operation by tapping lightly on the Touchpad twice. (Figure 2-13) Setup Utility on page 33 for more information) CLICKING Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the Touchpad once. (Figure 2-12) Figure 2-13 Double-clicking 21 LifeBook C Series – Section Two SCROLLING POINT If the interval between clicks is too long, the double-click will not be executed. POINT Parameters for the Touchpad can be adjusted from the Mouse Properties dialog box located in the Windows Control Panel. Using the Scrolling button allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To use the Scrolling button, press the crescent shape at the top or bottom of the button to scroll up or down a page. When you have reached the desired section of the page, release the button. (Figure 2-15) DRAGGING Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then release your finger. (Figure 2-14) Figure 2-14 Dragging 22 Figure 2-15 Scrolling TOUCHPAD CONTROL ADJUSTMENT The Windows Control Panel allows you to customize your Touchpad with selections made from within the Mouse Properties dialog box. Volume Control Volume Control Your Fujitsu LifeBook has multiple volume controls which interact with each other. CAUTION Any software that contains audio files will also contain a volume control of its own. Both the main LifeBook volume control and the software volume control will interact with each other, but it should be noted that if you set your software volume to Off, you will override the main volume control setting and the software setting will control the maximum knob setting. CONTROLLING THE VOLUME There is the hardware volume control located on the LifeBook itself, and the volume control set from within the Volume Control on the Taskbar. In addition to those, there are also application volume controls that are set within each program individually. Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. For example: ■ Your hardware volume control is all the way down, therefore your individual software application’s volume control has no effect on the volume. We recommend that you use the hardware volume controls to set the upper limit for the sound level and then make fine adjustments with the Volume Control on the Taskbar and individual application software. SETTING THE HARDWARE VOLUME CONTROL 1. Turn the volume control knob to the right of your LifeBook to increase the volume. 2. Turn the volume control knob to the left to decrease the volume. (See figure 2-5 on page 12 for location) 23 LifeBook C Series – Section Two Selector Switch CoolView Display Application Launcher buttons Figure 2-16 LifeBook Application Launcher Buttons LifeBook Application Panel A unique feature of your Fujitsu LifeBook is the LifeBook Application Panel. This panel allows you to operate the DVD drive as an independent audio CD Player or launch applications with the touch of one button even when your system is in standby mode or pseudo-off mode. POINT LifeBook Application Panel uses the date and time settings of your LifeBook. If the date and time are off, you can adjust this setting in the Windows Control Panel. Your LifeBook is pre-installed with software utilities that let you operate and configure your LifeBook Application Panel. These utilities are found under the Start menu, under Programs, then under LifeBook Application Panel. They include a CD Player, Application Panel Setup, Application Panel Guide, Activate Panel and Deactivate Panel. The LifeBook Application Panel system makes your LifeBook more than just another notebook computer. POINT The CD Player only works with audio CDs. Neither the CD Player or launch buttons will work when the power switch is in the Off position. 24 The panel consists of the following elements: SELECTOR SWITCH Located at the far left of the panel, this switch allows you to select the function of the panel—either as an Application Launcher, a CD Player, or as a lock. Set the switch to the middle position when the Application Launcher buttons are not being used. APPLICATION LAUNCH CD PLAYER BUTTONS When the selector switch is in the Application position, pressing any of the buttons will launch a user-defined application. When the selector switch is in the CD Player position, the buttons operate the CD player, and when the selector switch is in the Lock position, the buttons are disabled and do nothing when pressed. COOLVIEW DISPLAY The CoolView display presents a variety of information, including the number of the audio track being played, the battery status, and system status. Refer to “CoolView Display” on page 16 for detailed information about the contents of the display. CONFIGURING YOUR LIFEBOOK APPLICATION PANEL When you start Windows 98 Second Edition, the LifeBook Application Panel is automatically activated. An icon resembling a finger pressing a button will appear on the system tray (the indented portion of the status bar where the clock is displayed). When you see this icon you will know that the LifeBook Application Panel is active. LifeBook Application Panel As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature. To configure your LifeBook Application Panel with Application Panel Setup: 1. Click on Start. 2. Click on Programs. 3. Click on LifeBook Application Panel. 4. Click on Application Panel Setup. The Application Panel Setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your LifeBook, these buttons are pre-configured to launch the following programs: ■ ■ ■ ■ Application A – Microsoft Works Application B – Quicken® Internet – Internet Explorer® E-Mail – Netscape® Messenger POINT The tabs in Application Panel Setup may not be in the same order as the buttons on your LifeBook, please select the tab you wish to change carefully. To change an application associated with the Application A, Application B, or E-mail buttons, click on the tab for the button you would like to reconfigure – for example, Application A. Click on Browse from Start Menu, scroll down the list of applications, click on the application you wish to launch with this button, and then click OK. The button will now launch the new application. The Internet tab is different. It comes set to launch your Windows 98 Second Edition default Internet browser, (Internet Explorer, unless you have changed this in Windows 98 Second Edition.) In order to reconfigure it to launch another program follow these easy steps: 1. Click on Other from the Internet browser box. 2. Click on Browse from Start Menu. 3. Scroll down the list of applications, and the click on the application you wish to launch with this button. 4. Click OK. Internet browser box. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above. POINT The Internet or E-mail buttons can be configured to launch any application you wish, not just an Internet browser or e-mail program. At the bottom of each application setup page are two selectable options. The first will enable/disable the button when your LifeBook is in Standby mode, and the second will enable/disable the button when your LifeBook is in the pseudo-off state. You can enable/disable either or both of these functions simply by clicking on the option. POINT If you choose to have the buttons work when the LifeBook is in standby or pseudo-off, they will function even if hit accidentally, and will turn on your LifeBook even if you are not present or using your LifeBook. This could deplete your battery, and you will need to recharge it before using the LifeBook. As a precaution, move the selector switch to the Lock position when you are away from your LifeBook. When you have finished with Application Panel Setup, click on OK, and the new settings will take effect. You can reconfigure your LifeBook Application Panel as often as you like. USING THE CD PLAYER The CD player enables you to use your LifeBook’s DVD drive as an audio CD player, even when your LifeBook is in the pseudo-off state, in stand-by mode or in suspend mode. As long as the power switch is in the On position, the CD player will function. POINT If you shut down from Windows while the CD player is playing an audio CD, it will stop. To continue to use the CD Player, turn the power switch to the On position and press the play button. The audio CD will start playing at Track 1. The button will now launch the new application. If you want to return to launching your Windows 98 Second Edition default Internet browser with this button, you need only click on “Default Internet Browser” from the 25 ! LifeBook C Series – Section Two POINT You cannot go into Suspend Mode or Hibernation (Save-to-Disk) Mode while the CD Player is playing a CD. If you press the Suspend button, your LifeBook will not suspend until you stop the CD Player. POINT If you slide the Selector switch to either Lock or Application while an audio CD is playing, it will stop. You will not be able to start it again until you have returned the Selector switch to the CD Player position. You cannot use the CD Player at any time unless the Selector switch is in the CD Player position. There is no configuration required for CD player operation. The buttons are pre-configured to work like a normal CD player. When the selector switch is in the bottom position, the buttons will operate as follows: ■ Stop/Eject: This is the first button to the right of the CoolView display. If you press it once, it will stop an audio CD that is playing. If you press it twice, it will eject the audio CD. ■ Play/Pause: This is the second button to the right of the CoolView display. Press this button to start playing an audio CD starting at Track 1. While the audio CD is playing, press it to pause. Press it again to continue. POINT If you press the play button and nothing happens, you either have the Selector switch set to the Application or Lock position, there is no audio CD in the DVD drive, or you have a CD other than an audio CD in the drive. POINT Because of the Windows CD auto-insertion function, audio CDs will start playing immediately after they are inserted if your LifeBook is On. This will not happen if you are using the CD Player in Suspend or Pseudo-off modes. ■ ■ Fast Backward: This is the third button to the right of the CoolView display. Press this button once to skip one track back. Fast Forward: This is the fourth button to the right of the CoolView display. Press this button once to skip forward one track. 26 DESKTOP CONTROL PANEL Your LifeBook includes a desktop control panel for your LifeBook’s desktop that you can use at any time. You may use this panel to operate the CD player when you have the Selector switch in the Application or Lock position. To use the desktop control panel: 1. Click on Start. 2. Click on Programs. 3. Click on Lifebook Application Panel. 4. Click on Display CD Player. The desktop control panel will appear in the upper right corner of your screen. To close the panel: 1. Click on the “x” button. To minimize the panel: 2. Click on the “-” button. You can select from four appearances for your desktop control panel. Simply double click on the track display area of the panel, and a menu will appear which will allow you to select from a pull down menu. On the same pop-up are two other options: “Always on top” and “Continuous Play”. If you click on “Always on top” the desktop controls will always be seen on your screen, no matter what other application you are running. If you click on “Continuous Play”, your CD Player will automatically start over at the beginning of the CD in the drive as soon as it finishes the last track. You can move the desktop control panel to anywhere on your desktop. Drag it by clicking on the track number display, holding it down, and dragging the control panel. When you place it where you would like, release the mouse button. POINT If you have your display set to 256 colors the basic display will appear no matter which one you select. You will need to set your display colors to more than 256 in order to select other display appearances. POINT When you close the CD Player’s desktop control panel, it will stop the audio CD Player. Simply press the Play button if you would like to continue listening, and the CD Player will restart at track 1. The Selector switch must be in the CD Player position. " LifeBook Application Panel Deactivating and Activating the LifeBook Application Panel To deactivate the LifeBook Application Panel, follow these easy steps: 1. 2. 3. 4. Click on Start. Click on Programs. Click on LifeBook Application Panel. Click on Deactivate Panel. To reactivate, follow the same procedure, except for step 4. Click on Activate Panel instead. POINT Application Panel Setup If you insert an audio CD which has both audio and data tracks into the DVD drive, the CD Player may fail to play the first audio track. ■ ■ The Volume Up, Volume Down and Mute controls for the CD player desktop control panel adjusts the volume of the CD audio line only. It does not adjust your LifeBook’s master software volume control or the manual volume on the LifeBook. ■ The CD player desktop control panel is designed to be displayed in High Color (16-bit) or in True Color (24-bit or more). If you have your LifeBook’s display set for 256 colors or less CD Player will display in a “basic” mode. Every time you start Windows 98 Second Edition, the LifeBook Application Panel is activated. Even if you deactivated it before you shut down. 27 LifeBook C Series – Section Two Pre-Installed Software Your Fujitsu LifeBook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. LEARNING ABOUT YOUR APPLICATIONS Tutorials All operating systems and most application software have tutorials built-into them upon installation. We highly recommend that you step through the tutorial before you use an application. Manuals Included with your LifeBook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are available online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications. PC-DOCTOR FOR WINDOWS PC-Doctor for Windows by PC-Doctor.com, Inc., is a diagnostic software primarily for use by your support representative when assisting you with troubleshooting. LAPLINK 2000 LapLink 2000, by LapLink.com Inc., allows you to transfer files directly to other computers via an internal modem, a PC Card modem, the infrared port, the USB port, or a serial or parallel cable (cables not included). (See your LapLink online help for proper operating procedures) QUICKEN 2000 BASIC Quicken 2000 Basic by Intuit is a personal money management program. It has features such as portfolio management, account registries, on-line banking and bill paying features. MCAFEE.COM ACTIVESHIELD ActiveShield, by McAfee.com, is an antivirus program that can be run after loading data or programs onto your LifeBook. It assists in protection of the data currently on your hard disk from contamination and destruction. (See your ActiveShield online help or manual for more information on how and when to run this program) MCAFEE.COM CLINIC (ON-LINE COUPON) Clinic, by McAfee.com, is a web-based antivirus program that can be run from the McAfee.com website after loading data or programs onto your LifeBook. It 28 assists in the protection of the data currently residing on your hard disk from destruction or contamination. (Go to http://www.mcafee.com for more information on how and when to run this program.) PMSET 98 PMSet 98 allows you to monitor and manage your battery status. (See your PMSet 98 online help for more information on the correct way to use this program) POINT As your LifeBook does not support the CPU Clock control, the option is not active within the Power Control menu of PMSet 98. ADOBE ACROBAT READER The Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms. INTEL SPEEDSTEP Intel SpeedStep allows your LifeBook to operate in dual modes. When connected to AC source, the system operates in Maximum Performance Mode. When powered by battery, the system switches to Battery Optimized Mode to conserve battery life. The SpeedStep software is automatically loaded when you start your system and appears on the system tray as a flag in one of two modes. (1) A checkered flag indicates that the system is set for Maximum Performance Mode. (2) A blue flag with a green center square indicates that the system is set for Battery Optimized Mode. You can change the setting or disable the software by double clicking the flag icon and changing the settings in the Intel SpeedStep Technology window. MICROSOFT WORKS 2000 Microsoft Works 2000 is a suite of software containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory. MICROSOFT PRESS INTERACTIVE TRAINING FOR WINDOWS 98 Microsoft Press Interactive Training for Windows 98 is an on-line tutorial designed to help you become familiar with your LifeBook’s operating system. # Pre-Installed Software INTERVIDEO WINDVD SOFTWARE DVD PLAYER The WINDVD software provides a DVD decoder/player which allows you to playback DVDs on your LifeBook. LIFEBOOK APPLICATION PANEL SOFTWARE Your LifeBook is pre-installed with software utilities that let you operate and configure your LifeBook Application Panel. These utilities are found under the Start menu, under Programs, then LifeBook Application Panel. They include a CD Player, Application Panel Setup, Application Panel Guide, Activate Panel and Deactivate Panel. 29 LifeBook C Series – Section Two 30 # 3 Getting Started 29 LifeBook C Series – Section Three 30 Power Sources DC Output Cable DC Power Jack AC Cable AC Adapter Figure 3-1 Connecting the AC Adapter Power Sources Your Fujitsu LifeBook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter. CONNECTING THE POWER ADAPTERS The AC adapter or optional Auto/Airline adapter provides power for operating your LifeBook and charging the batteries. Connecting the AC Adapter 1. Plug the DC output cable into the DC power jack of your LifeBook. 2. Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter 1. Plug the DC output cable into the DC power jack on your LifeBook. 2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or Accessories position. OR 3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat. Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power 1. Be sure that you have at least one charged battery installed. 2. Remove the AC adapter or the Auto/Airline adapter. CAUTION The Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your LifeBook. 31 LifeBook C Series – Section Three Display Panel Latch Figure 3-2 Opening the Display Panel Display Panel Your Fujitsu LifeBook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of activematrix technology. OPENING THE DISPLAY PANEL 1. Slide the latch located at the top of the display panel to the right. This releases the locking mechanism and raises the display slightly. 2. Lift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle. ADJUSTING DISPLAY PANEL BRIGHTNESS Once you have turned on your LifeBook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness, keyboard and power management utility. Keyboard Adjusting the brightness using the keyboard changes the setting only temporarily. ■ [FN+F6]: Pressing repeatedly will lower the brightness of your display. ■ [FN+F7]: Pressing repeatedly will increase the brightness of the display. 32 POINT If using AC power, your brightness setting is set to its highest level by default. If using battery power, your brightness settings is set to its lowest level by default. Power Management Utility Adjusting the brightness using the Power Management changes the setting permanently. 1. Double-click the Battery icon in the lower right corner of your display. This will open the PMSet 98 Properties dialog box. 2. Select the Power Control tab and adjust your LCD Backlighting to the desired level. 3. Click OK or Apply to permanently change the settings. You may need to readjust the brightness level periodically depending on your operating environment. POINT The higher the brightness level, the more power the LifeBook will consume and the faster your batteries will discharge. For maximum battery life, set the brightness to as low a level as possible. CLOSING THE DISPLAY PANEL 1. Holding the edge of your display panel, pull it forward until it is flush with the body of your LifeBook. 2. Push down until you hear a click. This will engage the locking mechanism and prevent your display panel from opening unexpectedly. S t a r t i n g Yo u r L i f e B o o k Starting Your LifeBook POWER ON Power Switch The power switch is used to turn on your LifeBook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook. (See figure 2-4 on page 11 for location) CAUTION When you turn on your LifeBook be sure you have a power source. This means that at least one battery is installed and charged, or that the AC or Auto/Airline adapter is connected and has power. BOOT SEQUENCE The procedure for starting-up your Fujitsu LifeBook is termed the Bootup sequence and involves your LifeBook’s BIOS. When your LifeBook is first turned on, the main system memory is empty, and it needs to find instructions to start up your LifeBook. This information is in the BIOS program. Each time you power up or restart your LifeBook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your LifeBook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen. The boot sequence is executed when: ■ Facing the keyboard and display panel, move the power switch towards the back of your LifeBook. This is the On position. The power switch moved toward the front of your LifeBook is in the Off position. When you are done working you can either leave your LifeBook in Suspend mode, (See Suspend Mode on page 36 for more information), or you can turn it off. (See Power Off on page 38 for more information) CAUTION Do not carry your LifeBook around with the power on or subject it to shocks or vibration, as you risk damaging your LifeBook. ■ ■ ■ BIOS SETUP UTILITY The BIOS Setup Utility is a program that sets up the operating environment for your LifeBook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your LifeBook. The BIOS Setup Utility configures: ■ When you Power On your LifeBook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook will emit an audio warning and/or an error message will be displayed. (See Power On Self Test Messages on page 67 for more information) Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings. After satisfactory completion of the Power On Self Test (POST), your LifeBook will load your operating system. CAUTION Never turn off your LifeBook during the Power On Self Test (POST) or it will cause an error message to be displayed when you turn your LifeBook on the next time. (See Power On Self Test Messages on page 67 for more information) You turn on the power to your LifeBook. You restart your LifeBook from the Windows Shut Down dialog box. The software initiates a system restart. Example: When you install a new application. You reset the system by pressing the three keys [CTRL+ALT+DEL]. ■ Device control feature parameters, such as changing I/O addresses and boot devices. System Data Security feature parameters, such as passwords. Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following: 1. Turn on or restart your LifeBook. 2. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed. 3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings. BIOS Guide A guide to your LifeBook’s BIOS is available online. Please visit our service and support Web site at www.8fujitsu.com. Once there, click on the Self Help Center link, and select your LifeBook series from the 33 LifeBook C Series – Section Three pull-down menu. Once you have done that, select the heading BIOS Guides from the pull-down menu and finally, select your specific unit’s BIOS number. If you are unsure of your LifeBook’s BIOS number, please refer to your packing slip. POINT If your data security settings require it, you may be asked for a password before the BIOS main menu will appear. BOOTING THE SYSTEM WITH WINDOWS 98 SECOND EDITION We strongly recommend that you not attach any external devices and do not put a DVD/CD or floppy disk in any drive until you have gone through the initial power on sequence. When you turn on your LifeBook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will read the hard drive for the operating system software, flash the LifeBook configuration information on the screen, and then the Windows 98 Second Edition Welcome will begin. Designed to accommodate the needs of many users, in many different countries, Windows 98 Second Edition needs to be configured the first time you use them. Windows 98 Second Edition has three parts: ■ ■ ■ Getting Started: You have the opportunity to enter custom information for your configuration file and setup your modem so that your LifeBook will be prepared to dial out. Registration: Easy online registration for Windows 98 Second Edition with Microsoft, and for your LifeBook with Fujitsu PC Corporation. Windows License Agreement and Final Settings: You have the opportunity to review the Windows 98 Second Edition License Agreement and then your configuration file will be generated. POINT You may click Cancel at any time within this process to shutdown Windows 98 Second Edition. You may restart this process at any time in the future, but you must complete it in order to use your computer. 34 Getting Started Read the instructions on the screens carefully and fill in the information as directed. You will be asked for such items as the language you wish to use, the country in which you live, your first and last name, and about how you dial out from where you will be using your LifeBook. For the modem settings, enter your current location information where you will be using your LifeBook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button, and you will go directly to the condition of use page. Once you have set up your LifeBook to dial out, Windows 98 Second Edition will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings please contact Fujitsu PC Service and Support. (See Fujitsu PC Contact Information on page 3 for more information) If you would simply like to move on, and register at a later time, you may click the Skip button, and you will go directly to the Condition of Use page. Registration If your connection is successful, you will go to the Registration Confirmation page. On this page simply enter the requested information, and then check the box at the bottom to register your copy of Windows 98 Second Edition with Microsoft. Once you have finished, click the Next button to continue. POINT If you do not register at this time you can do it later simply by double-clicking on the LifeBook Registration icon on your desktop and following the instructions. You will then go through the Fujitsu registration process. Follow the instructions on the screens, and enter all of the necessary information. Be as specific as possible so that if you need help the service and support team will be able to serve you better. Final Settings The first part of your final settings is the Windows End User License Agreement. Read the agreement carefully. When you finish reading you must accept or reject the terms of the agreement and then click on the Next button. S t a r t i n g Yo u r L i f e B o o k POINT Book Registration icon on your desktop at any time and follow the instructions. If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows 98 Second Edition or to shut down your LifeBook. POINT You cannot use your LifeBook until you have accepted the License Agreement. If you stop the process your LifeBook will return to the beginning of the Windows Welcome Process, even if you shut your LifeBook down and start it up again. POINT Make sure you have connected a phone line to your modem before you use E-Registration. You may also complete the pre-printed registration form and either: ■ ■ ■ REGISTERING YOUR LIFEBOOK What are the benefits of registering? You will receive an identification label for your LifeBook, which, if your LifeBook is ever lost, may help in getting it returned to you. You also receive priority Personal Identification Number (PIN) technical support access and useful product mailings. Proof of purchase is not required if you register within 30 days of your purchase. Fax to 1-408-496-0609 Mail to: Fujitsu PC Corporation 5200 Patrick Henry Drive Santa Clara, CA 95054 Attn: Warranty Department Call: 1-800-8fujitsu (1-800-838-5487) You may also register on our Web site: ■ www.8fujitsu.com You will need to be set up with an Internet Service Provider (ISP) to use this option. POINT How do I register? With Windows 98 Second Edition, it is a part of the Windows Welcome process. If you do not register during the Welcome process you can double-click on the Life- You can also register your Fujitsu LifeBook via mail, telephone or fax. 35 ! LifeBook C Series – Section Three Power Management Your Fujitsu LifeBook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your LifeBook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility. Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your LifeBook into Suspend mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings. SUSPEND/RESUME BUTTON When your LifeBook is active, the Suspend/Resume button can be used to manually put your LifeBook into Suspend mode. Push the Suspend/Resume button when your LifeBook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Suspend mode. If your LifeBook is suspended, pushing the Suspend/ Resume button will return your LifeBook to active operation. You can tell whether or not your system is in Suspend mode by looking at the Power indicator. (See figure 2-8 on page 16) If the indicator is visible and not flashing, your LifeBook is fully operational. If the indicator is both visible and flashing, your LifeBook is in Suspend mode. If the indicator is not visible at all, the power is off or your LifeBook is in Hibernation (Save-toDisk) mode. (See Hibernation Mode) SUSPEND MODE Suspend or Standby mode in Windows 98 Second Edition saves the contents of your LifeBook’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your LifeBook can be put in Suspend mode by: ■ ■ Pressing the Suspend/Resume button when your system is turned on. Selecting Standby from the Windows Shut Down menu. 36 ■ ■ Timing out from lack of activity. Allowing the battery to reach the Dead Battery Warning condition. Your LifeBook’s system memory typically stores the file(s) on which you are working, open application(s) information, and any other data required to support the operation(s) in progress. When you resume operation from Suspend mode, your LifeBook will return to the point where it left off. You must use the Suspend/Resume button to resume operation, and there must be an adequate power source available, or your LifeBook will not resume. CAUTION If you are running your LifeBook on battery power, be aware that the battery continues to discharge while your LifeBook is in Suspend mode, though not as fast as when fully operational. HIBERNATION (SAVE-TO-DISK) FEATURE The Hibernation (Save-to-Disk) feature saves the contents of your LifeBook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature The default settings are not enabled. To enable or disable the Hibernation feature, follow these steps: 1. From the Start menu, select Settings, and then select Control Panel. 2. From the Control Panel, select Power Options. 3. Select the Hibernation tab. Select the box to enable or disable this feature. Using the Hibernation Feature 1. From the Start menu, select Settings, then select Control Panel. 2. From the Control Panel, select Power Options. 3. Select the Advanced tab. Select Hibernate from the pull down menu for Power buttons. POINT Disabling the Suspend/Resume button prevents it from being used to put your LifeBook in Suspend or Hibernation (Save-to-Disk) mode. The resume function of the button cannot be disabled. " Power Management CAUTION The Suspend or Hibernation (Save-to-Disk) mode should not be used with certain PC Cards. Check your PC Card documentation for more information. display and turns off the hard drive when there is no activity (keystroke, pointer action, sound generation, video display change, modem transmission or reception, etc.) on your LifeBook for the user-selected Standby time-out period. Any activity will cause your LifeBook to return to normal operation automatically. This feature is independent of the Suspend/Resume button. POINT If your LifeBook is actively accessing information when you enter the Suspend or Hibernation (Save-to-Disk) mode, changes to open files are not lost. The files are left open and memory is kept active during Suspend mode or the memory is transferred to the internal hard drive during Hibernation (Save-to-Disk) mode. POINT When PC Cards or external devices are in use, Saveto-Disk mode cannot return to the exact state prior to suspension, because all of the peripheral devices will be re-initialized when the system restarts. POINT The main advantage of using the Hibernation (Save-toDisk) function is that power is not required to maintain your data. This is particularly important if you will be leaving your LifeBook in a suspended state for a prolonged period of time. The drawback of using Hibernation (Save-to-Disk) mode is that it lengthens the power down and power up sequences and resets peripheral devices. POINT Hibernation (Save-to-Disk) mode requires allocating a significant amount of hard drive capacity for saving all system memory, which reduces your usable disk space. When you purchase your LifeBook it will have space allocated for the memory installed. If you upgrade the original system by adding a memory upgrade module without changing the size of your Hibernation (Save-toDisk) allocation you will get an error message when you try to activate Hibernation (Save-to-Disk) mode and it will not work. Use the PHDISK Utility to increase the size of the Hibernation (Save-to-Disk) file, SAVE2DSK.BIN. You can download the Hibernation (Save-to-Disk) File Allocation information from our Web site at www.8fujitsu.com. If you need help, contact your support representative for recommendations. STANDBY MODE Standby mode is one of the power management parameters. When Standby mode is activated, your LifeBook puts the CPU in low-speed operation, shuts off the DISPLAY TIMEOUT The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS Setup Utility on page 33 for more information) HARD DISK TIMEOUT The Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS Setup Utility on page 33 for more information) WINDOWS 98 SECOND EDITION POWER MANAGEMENT The Power Management icon located in the Windows 98 Second Edition Control Panel allows you to configure some of the power management settings. For example, you can use the Power Management to set the timeout values for turning off the display and hard disks whether you are running the LifeBook on battery power or one of the adapters. (See Pre-Installed Software on page 28 for more information) The settings may also be changed in the BIOS. (See BIOS Setup Utility on page 33 for more information) RESTARTING THE SYSTEM If your system is on and you need to restart it, be sure that you use the following procedure. 1. Click the Start button, and then click Shut Down. 2. Select the Restart option from within the Windows Shut Down dialog box. 3. Click OK to restart your LifeBook. Your LifeBook will shut down and then reboot. 37 LifeBook C Series – Section Three CAUTION Turning off your LifeBook without exiting Windows or turning on your LifeBook within 10 seconds of the LifeBook being shut off may cause an error when you start the next time. POWER OFF Before turning off the power by choosing Shut Down from the Windows 98 Second Edition Start menu, check that the Hard Drive, DVD, PC Card and the Floppy Disk Drive Access indicators are all Off. (See figure 2-4 on page 11) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To assure that your LifeBook shuts down without error, use the Windows shut down procedure. CAUTION Never turn your LifeBook off while an application is running. Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power with the power switch. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors. Using the correct procedure to shut down from Windows, allows your LifeBook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is: 1. Click the Start button, and then click Shut Down. 2. Select the Shut Down option from within the Windows Shut Down dialog box. 3. Click OK to shutdown your LifeBook. If you are going to store your LifeBook for a month or more see Care and Maintenance Section. 38 # 4 User Installable Features 39 LifeBook C Series – Section Four 40 Lithium ion Battery Lithium ion Battery located on the Status Indicator panel. The indicator changes as the battery level changes. Your Fujitsu LifeBook has a Lithium ion battery that provides power for operating your LifeBook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards. The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook and connect the AC or Auto/Airline adapter. The Lithium ion battery operating time may become shorter if it is used under the following conditions: ■ ■ When used at temperatures that exceeds a low of 5°C or a high of 35°C. Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. (See Battery Charging Indicators on page 17 for more information) When using a high current device such as a modem, DVD, or hard drive, using the AC adapter will conserve your battery life. CAUTION Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences. DVD drive, CD-ROM drive or hard drive usage may also have a significant impact on battery life. The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one. CAUTION Do not leave a faulty battery in your LifeBook. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your LifeBook itself. It may also prevent operation of your LifeBook by draining all available current into the bad battery. POINT Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel. There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your LifeBook is in use while the battery is charging. If you want to charge the battery more quickly, put your LifeBook into Suspend mode, or turn it off while the adapter is charging the battery. (See Power Management on page 36 for more information on Suspend mode and shutdown procedure) CAUTION Using heavy current devices such as a Modem or frequent DVD accesses may prevent charging completely. Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your LifeBook will go into Suspend mode. There is no guarantee that your data will be saved once the LifeBook reaches this point. CAUTION CAUTION Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8FUJITSU (1-800-838-5487). RECHARGING THE BATTERIES If you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator Once the low battery notification message appears, you need to save all your active data and put your LifeBook into Suspend mode until you can provide a new power source. You should provide a charged battery, an AC power adapter, or Auto/Airline adapter as soon as possible. CAUTION When you are in Suspend mode there must always be at least one power source active. If you turn off the power with the power switch, or remove all power sources while your LifeBook is in Suspend mode, any data that has not been saved to the hard drive will be lost. 41 LifeBook C Series – Section Four Dead Battery Suspend mode shows on the Status indicator just like the normal Suspend mode. Once your LifeBook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your LifeBook while an adapter is charging the battery. Shorted Batteries The Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See figure 29 on page 17) If this display shows a Shorted Battery, it means that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook. (a) (d) (b) (e) (c) (f) Figure 4-1 Replacing the Battery REPLACING THE BATTERY With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. (Figure 4-1) 1. Have a charged battery ready to install. 2. Shut down your LifeBook and disconnect the AC adapter. 3. Slide the battery release panel open. 4. Remove the battery from the bay. 5. Slide the new battery into the bay. 6. Slide the battery release panel close. 7. Plug in the AC adapter and turn the power on. 42 CAUTION If the Lithium ion battery connector is not fully seated, you may not be able to use your LifeBook or charge your battery. Floppy Disk Drive Eject Button Figure 4-2 Loading/Ejecting a 3.5” Floppy Disk Floppy Disk Drive Your Fujitsu LifeBook has a 3.5" floppy disk drive with the ability to read and write information on removable 1.44MB and 720KB floppy disks. LOADING A DISK To load a disk into your disk drive, follow these easy steps: matted. (Please refer to your operating system manual for step-by-step instructions on formatting a disk) To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. 1. Orient the disk so that its label is facing upwards and the shutter side is pointing towards the drive. 2. Push the disk into the drive until the Eject button pops out and you hear a click. Write Enabled POINT When there is no disk in the drive, the Eject button is flush with your LifeBook. Write Protected EJECTING A DISK To eject a disk from the disk drive, follow these easy steps: 1. Check that the Floppy Disk Drive Access indicator is inactive. 2. Press the Eject button. This will push your disk partially out of the drive. 3. Remove the disk. Figure 4-3 Floppy Disk Write Protect CAUTION Formatting a floppy disk that already contains data will erase all of the information on the disk. CAUTION If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive. PREPARING A DISK FOR USE Before you can use a new disk, it needs to be prepared so your LifeBook knows where to store information. This preparation is called formatting or initializing a disk. You will need to format new disks, unless they are prefor43 LifeBook C Series – Section Four DVD/CD Holder Tray DVD/CD Eject Button Figure 4-4 DVD Drive DVD Drive Your Fujitsu LifeBook contains a DVD drive which is both a 8x DVD player and a CD drive. This gives you access to movie, software and audio DVD/CDs. DVD PLAYER SOFTWARE With the DVD drive and DVD Player software you can play DVD movies on your LifeBook. The DVD player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc. The DVD Player software is included on the CD labeled DVD Application CD. You may need to re-install your DVD Player software if: ■ ■ Your DVD Player software becomes corrupted and is not operating properly. You perform a complete system software recovery utilizing the recovery CD. 6. To use the DVD Player software, click Start, Programs, and then InterVideo WINDVD. Un-installing the DVD Player Software The DVD Player software should be removed if you wish to use a 3rd party DVD player instead of the Fujitsu DVD Player. To un-install the DVD Player software follow these easy steps: 1. Close any open files on the DVD drive. 2. Remove any DVD/CD from the drive. 3. From the Start menu, select Settings, and then select Control Panel. 4. Double-click the Add/Remove Programs icon. 5. Select the InterVideo WINDVD from the Add/ Remove Programs Properties dialog box. 6. Click the Add/Remove button and the DVD software will be un-installed. POINT POINT You should periodically check the Fujitsu Web site at www.fujitsupc.com for current updated drivers. Installing the DVD Player Software To install the DVD Player software follow these steps: 1. Make sure you either close or disable any open programs, applications and utilities. This includes the MS Office Toolbar, any anti-virus programs and screensavers. 2. Insert the DVD Application CD into the DVD drive. If the CD AutoRun feature activates, skip Step 3. 3. From the Start menu, select Run, type D:\WINDVD\Setup.exe and click OK. 4. Go through the installation process by following the directions on screen. 5. Once the installation is complete, you will be asked to restart your LifeBook. 44 If you wish to use a 3rd party DVD player software, you must un-install the InterVideo WINDVD software or the 3rd party DVD Player software may not operate correctly. CAUTION Do not operate your DVD drive unless your LifeBook is sitting on a flat surface. Using a DVD/CD when the drive is not level may damage the drive or prevent proper operation. CAUTION Prolonged use of the DVD drive, such as watching a DVD movie, will substantially reduce your battery life. LOADING A DVD/CD To load a DVD/CD into your DVD drive, follow these steps: DVD Drive 1. Push and release the eject button on the front of the DVD drive to open the holder tray. The tray will come out of the LifeBook a short distance. 2. Gently pull the tray out until a DVD/CD can easily be placed in the tray. CAUTION There may be a protective sheet in the tray when it was shipped, please make sure it is removed before operating. 3. Place the DVD/CD into the tray, label side up, with the hole in the center of the DVD/CD. Snap the DVD/ CD onto the raised circle in the center of the tray. 4. Gently push the holder tray back in until you hear a click. (Figure 4-5) POINT If you have disabled the Auto Insert Notification Function, you will have to start the DVD/CD from your desktop, as your LifeBook will not automatically recognize that a DVD/CD has been loaded. (b) (a) USING THE DVD PLAYER SOFTWARE POINT For details on using your DVD player go to the Start menu and select Programs, InterVideo DVD, then select either InterVideo DVD Help or InterVideo DVD Readme. Starting a DVD Movie 1. Insert the DVD movie into the DVD drive of your LifeBook. If the CD AutoRun feature activates, skip Step 2. 2. From the Start menu, select Programs, then select InterVideo WINDVD and click InterVideo WINDVD or double-click on the InterVideo WINDVD icon on the desktop. This will launch the DVD movie. 3. Click OK to close the About DVD Player Performance dialog box and the movie will begin. Opening the DVD Player Control Panel With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the DVD Player control panel and the mouse. 1. Right-click on the movie screen to open a dropdown menu for options. 2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen. Using the DVD Player Control Panel The DVD Player software allows you to watch the movie much like a VCR player. You have the option to pause, rewind, fast-forward and stop the movie at any point. (c) (d) Figure 4-5 Loading/Ejecting a DVD/CD REMOVING A DVD/CD 1. Push and release the eject button on the front of the DVD drive. This will stop the DVD/CD and the holder tray will come out of the LifeBook a short distance. 2. Gently pull the tray out until the DVD/CD can easily be removed from the tray. 3. Carefully remove the DVD/CD from the holder tray. 4. Gently push the holder tray back in until you hear a click. 1. To Pause the movie, click the! button. 2. To Rewind the movie, click the " button to rewind to a specific portion of the movie, or the # button to return to the opening screen. 3. To Fast-forward the movie, click the $ button to forward to a specific portion of the movie, or the% button to jump to the ending credits. 4. To Stop the movie, click the & button. Exiting the DVD Player 1. Click on the ' located in the upper right corner of the title bar. This will open a DVD Player dialog box. 2. Click Yes to stop and exit the movie, or No to close the DVD Player dialog box and return to the movie. 45 ! LifeBook C Series – Section Four USING THE DVD PLAYER ON BATTERY POWER Since DVD drives consume a lot of power, your overall battery life will be shorter when operating the DVD drive continuously (such as watching a DVD movie) than during standard operation. Many movies run-times are longer than your LifeBook can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety. battery. Or if you do not have an additional battery, you may attach AC power as soon as you see the low battery warning. 5. Resume your LifeBook by pressing the Suspend button again. This step is not required if you attached AC power without entering suspend mode. 6. Restart your DVD player, locate and skip to the chapter of the movie you were last watching. 7. Continue watching your DVD movie. POINT CAUTION Prolonged use of the DVD drive, such as watching a DVD movie, will substantially reduce your LifeBook’s battery life. Some shorter DVD movies may not require you to swap batteries or attach AC power to complete them. However, it is best to be prepared since actual battery life while operating the DVD drive cannot be guaranteed. AUTO INSERT NOTIFICATION FUNCTION CAUTION Many movies run-times are longer than your system can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety. POINT An additional fully-charged battery is highly recommended if you will be watching DVD movies on battery power. If you don’t have an additional battery, you may purchase one either on-line at FPCDirect.fujitsupc.com or call 1-877-FPCDirect (1-877-372-3473). To Watch a Movie on Battery Power: 1. Have an additional full-charged battery or your AC adapter ready for use. 2. Start watching your DVD movie. 3. When the low battery warning occurs, immediately stop the movie and exit the DVD player. CAUTION If you do not stop the DVD player quickly and the LifeBook attempts to auto-suspend (critical battery low state) the LifeBook will shutdown improperly. If this occurs, you will need to perform a hard reset and follow the instruction, if any, presented to you before the system will reboot. 4. Manually place your LifeBook into suspend mode by depressing the Suspend button and replace the discharged battery with an additional full-charged 46 The Auto Insert Notification function allows your LifeBook to automatically start a DVD/CD as soon as it is inserted in the DVD drive and the tray is closed. Your LifeBook will begin playing an audio DVD/CD or will start an application if the DVD/CD includes an auto run file. Disabling Auto Insert Notification Function To disable the Auto Insert Notification function, follow these easy steps: 1. Save all data and close all open applications. 2. From the Start menu, select Settings, and then select Control Panel. 3. Double-click the System icon. This will open the System Properties dialog box. 4. Select the Device Manager tab to display the device lists for your LifeBook. 5. Click on the + to the left of the DVD drive icon. The treeview will expand to show the DVD drive manufacturer’s name and model number. 6. Double-click on the DVD drive manufacturer’s name and model number. This will open the DVD drive manufacturer’s name and model number dialog box. 7. Select the Settings tab and then remove the check mark in the Auto Insert Notification box to turn it off. 8. Click OK. 9. Click Close in the System Properties dialog box, then click Yes in the System Settings Change pop-up window when it asks you to restart your machine and activate this change. The Auto Insert Notification function can be re-activated by repeating this process and placing a check mark in the Auto Insert Notification box to turn it back on. " PC Cards PC Card Slot PC Card Eject Button Figure 4-6 Installing/Removing PC Cards PC Cards Your Fujitsu LifeBook supports Type I, Type II and Type III PC Cards, which can perform a variety of functions depending on which type of PC Card you install. You can install one or two PC Cards at a time, depending on its type. Type I and Type II PC Cards can be installed together, while Type III PC Cards must be installed alone. Some available PC Cards: ■ ■ ■ ■ ■ ■ ■ Zoomed Video cards (Type II, Slot 1 only). Fax/data modem cards (Type II). Local area network (LAN) cards (Type II). IDE solid-state disk cards (Type II). SCSI cards (Type II). ATA cards (Type III). Other PC Cards that conform to PCMCIA 2.1 or CardBus standards. For further information, refer to the instructions supplied with your PC Card. WARNING Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently damage the card, your LifeBook, or both. 1. See your PC Card manual for specific instructions on the installation of your card. Some PC Cards may require your LifeBook to be Off while installing them. 2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards. 3. Insert your PC Card into the slot, with the product label facing up. 4. Push the card into the slot firmly until it is seated in the opening. You will hear a click and the Eject button will pop away from your LifeBook. 5. Flip the Eject button towards the front of your LifeBook. 6. Lock the PC Card into the slot by sliding the Lock button toward the front of your LifeBook. INSTALLING PC CARDS PC Cards are installed in the PC Card slot. To install a PC Card(s), follow these easy steps: WARNING Installing or removing a PC Card(s) during your LifeBook’s shutdown or bootup process may damage the card and/or your LifeBook. 47 LifeBook C Series – Section Four REMOVING PC CARDS To remove a PC Card(s), follow these easy steps: CAUTION Windows has a shutdown procedure for PC Cards that must be followed before removing a card. (Please review your operating system manual for the correct procedure) 2. Unlock the PC Card from the slot by sliding the Lock button toward the rear of your LifeBook. 3. Flip the Eject button towards the back of your LifeBook until it is fully extended, and then push it in until it is flush with the LifeBook. This will push the PC Card slightly out of the slot allowing you to remove the card. CAUTION 1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your LifeBook to be in Suspend Mode or Off while removing them. POINT If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your LifeBook. Once your LifeBook has been shutdown, you must turn Off the power using the power switch. 48 If the PC Card(s) has an external connector and cable, do not pull the cable when removing the card. # Memory Upgrade Module Memory Upgrade Module Your Fujitsu LifeBook comes with 64MB or 128MB high speed Synchronous Dynamic RAM (SDRAM) factory installed. To increase your LifeBook’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. (a) CAUTION Do not remove any screws from the memory upgrade module compartment, except the ones specifically shown in the directions for installing and removing the memory upgrade module. INSTALLING A MEMORY UPGRADE MODULE To install a memory upgrade module follow these steps: (b) WARNING You must turn off power before installing the memory upgrade module. 1. Turn off power to your LifeBook using the power switch, and remove any power adapter (AC or auto/airline). 2. Turn your LifeBook face down on a clean work surface. 3. Using a Phillips head screwdriver, remove the three screws securing the RAM Expansion cover. Remove the cover. (c) CAUTION The memory upgrade module can be severely damaged by electrostatic discharge (ESD). Be sure you are properly grounded when handling and installing the module. 4. Align the connector edge of the memory upgrade module, chip side up, with the connector slot in the compartment. 5. Insert the memory upgrade module at a 45o angle and press it firmly onto the connector. 6. Press the memory upgrade module down into the compartment until it locks underneath the retaining clip. You will hear a click when it is properly in place. Figure 4-7 Adding Memory to the LifeBook POINT The memory upgrade module is not something you routinely remove from your LifeBook. Once it is installed, you should leave it in place unless you want to increase system memory capacity. 7. Replace the cover over the memory tray and reinstall the three screws. 49 LifeBook C Series – Section Four REMOVING A MEMORY UPGRADE MODULE 1. Perform steps 1 through 3 of Installing a Memory Upgrade Module. 2. Pull the clips sideways away from each side of the memory upgrade module at the same time. 3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the back of your LifeBook. POINT After changing your memory module configuration, you must complete the Resetting the Hibernation (Save-to-Disk) Parameters procedure in order for the Hibernation (Save-to-Disk) mode to operate properly on your LifeBook. (See Hibernation (Save-to-Disk) Feature on page 36 for more information) CHECKING THE COMPUTER RECOGNITION OF NEW MEMORY CAPACITY Once you have changed the system memory capacity by either adding or removing a memory upgrade module, be sure to check that your LifeBook has recognized the change. You can check the memory capacity by looking at the main menu of the BIOS setup: (a) (b) 1. Turn on the power to your LifeBook using the power switch. 2. Allow the system to start booting and press the F2 key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS setup with the current settings displayed. (See BIOS Setup Utility on page 33 for more information) Use the right arrow key to select Info in the BIOS Setup menu. The System Memory and the Extended Memory capacity, as detected by your LifeBook during the Power On Self Test (POST), are displayed at the bottom of the Info menu screen. The chart below shows you the possible displays that can be shown on the main menu screen. POINT If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see the Troubleshooting section starting on page 65) Installed (c) Figure 4-8 Removing a Memory Upgrade Module 4. Store the memory upgrade module in a static guarded sleeve. 5. Replace the cover by following step 7 of Installing a Memory Upgrade Module. 50 On Board Slot 1 64MB 64MB 64MB 64MB 0 32MB 64MB 128MB Displayed Total RAM System Installed Memory 640K 64MB 640K 96MB 640K 128MB 640K 192MB Extended Memory 63MB 95MB 127MB 191MB Device Ports Device Ports Your Fujitsu LifeBook comes equipped with multiple ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc. MODEM (RJ-11) TELEPHONE JACK The modem (RJ-11) telephone jack is used for an internal modem. To connect the telephone cable follow these easy steps: (See figure 2-5 on page 12 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. 3. Plug the other end of the telephone cable into a telephone outlet. WARNING The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. CAUTION The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload. CAUTION The internal modem on all Fujitsu LifeBooks from Fujitsu PC Corporation are certified for use in the United States and Canada. The modem may be certified in other countries. SERIAL PORT The serial port, or COMM port, allows you to connect serial devices, such as printers or scanners. In order to connect a serial interface device follow these easy steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. 3. Tighten the two hold-down screws, located on each end of the connector. PS/2 PORT The PS/2 port allows you to connect an external keyboard, and/or numeric keypad and mouse. In order to connect a PS/2 interface device follow these easy steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. POINT A mouse, keyboard, or keypad may be installed and automatically recognized by your LifeBook without restarting or changing setups. POINT The use of two PS/2 devices simultaneously from the port requires a PS/2 splitter. UNIVERSAL SERIAL BUS PORT The Universal Serial Bus port (USB) allows you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. In order to connect a USB device follow these easy steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. PARALLEL PORT 1394 PORT The parallel port, or LPT port, allows you to connect parallel devices, such as a printer to your LifeBook. In order to connect a parallel interface device follow these easy steps: (See figure 2-6 on page 13 for location) The 1394 port allows you to connect devices that are compliant with IEEE standard 1394. This port is effectively a very fast USB port. In order to connect a 1394 device, follow these steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. 3. Tighten the two hold-down screws, located on each end of the connector. 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. 51 LifeBook C Series – Section Four CAUTION Due to the ongoing changes in USB technology and standards, not all USB devices and/or drivers are guaranteed to work. INFRARED PORT The Infrared IrDA 1.1 (4Mbps) port allows for wireless data transfer between your LifeBook and other IrDAcompatible devices, such as another computer or a printer, without the use of a cable. (See figure 2-6 on page 13 for location) It is important to keep in mind that while carrying out this form of communication, both devices must be placed so their infrared ports are directly facing each other without obstruction. The devices must also be separated by at least 6" but no more than 36" for maximum performance. The following conditions may interfere with infrared communications: ■ ■ A television, radio remote control unit, or a wireless headphone is being used nearby. Direct sunlight, fluorescent light, or incandescent light shines directly on the port. Mouse receiver without the use of a cable. (See figure 2-3 on page 9 for location) MICROPHONE JACK The microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8"(3.5 mm) mono mini-plug in order to fit into the microphone jack of your LifeBook. In order to connect a microphone follow these easy steps: (See figure 2-5 on page 12 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. STEREO LINE-IN JACK The stereo line-in jack allows you to connect an external audio source to your LifeBook, such as an audio cassette player. Your audio device must be equipped with a 1/8" (3.5 mm) stereo mini-plug in order to fit into the stereo line-in jack of your LifeBook. In order to connect a external audio source follow these easy steps: (See figure 2-5 on page 12 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. POINT CAUTION The stereo line-in jack will not support an external microphone. Do not move either device while communication is active as it may interrupt data transmission. CAUTION CAUTION Be careful not to scratch the infrared port lens. Scratches, dirt, or other surface marks can degrade operation. Turn down the audio volume when connecting electronic devices to the line-in jack. The internal speakers might break if unexpected large sounds are inputted. DIGITAL AUDIO-OUT CONNECTOR POINT With Windows 98 Second Edition, you can use the Infrared Recipient application for infrared file transfers. LapLink Professional software can also be used for infrared file transfers. WIRELESS INFRARED (IR) MOUSE RECEIVER The Wireless IR Mouse Receiver allows you to use an optional wireless Infrared Mouse (IR Mouse). The optional IR Mouse communicates directly with the IR 52 The digital audio-out connector allows you to download digital audio to Sony or Philips MiniDisc players. It uses SPDIF (Sony Philips Digital Interface) format. Please use the following setting when using the digital audio-out connector. (See figure 2-5 on page 12 for location) 1. Click on Start, Settings and then click on Control Panel. 2. Select Yamaha Ds-XG Audio Configuration. Device Ports 3. Click on the SPDIF tab and click ON (Digital Sources Only) WARNING Do not look into the connector. There is a beam coming out from the SPDIF connector, so do not look into the connector when inserting the cable. phones or speakers follow these easy steps: (See figure 25 on page 12 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. POINT If you plug headphones into the headphone jack, you will disable the built-in stereo speakers. POINT The frequency of the digital sound output from the SPDIF output connector is fixed to 48KHz. If a sampling rate convertor is not installed in your connecting digital electronic device (e.g., MD player), recording is not possible. Please see the user manuals for the electronic devices for further details. POINT The sound recorded through connecting a digital electronic device (e.g., MD player) to the SPDIF output connector cannot be used as digital output. All output data from the SPDIF output connector has copyright protection information included. CAUTION Please be careful, as there are several types of cables for connecting a digital electronic device (e.g. MD player) to the digital audio-out connector, depending on the connector type. The connector on your computer is a Optical Mini Plug (3.5mm diameter mini plug) EXTERNAL MONITOR PORT The external monitor port allows you to connect an external monitor. In order to connect an external monitor follow these easy steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. 3. Tighten the two hold-down screws, located on each end of the connector. CAUTION Pressing the [FN] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor. S-VIDEO OUT PORT The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture than NTSC or PAL. In order to connect an S-Video device, follow these easy steps: (See figure 2-6 on page 13 for location) 1. Align the connector with the port opening. 2. Push the connector into the port until it is seated. HEADPHONE JACK The headphone jack allows you to connect headphones or powered external speakers to your LifeBook. Your headphones or speakers must be equipped with a 1/8" (3.5 mm) stereo mini-plug. In order to connect head- 53 LifeBook C Series – Section Four 54 5 Troubleshooting 55 ! LifeBook C Series – Section Five 56 " Tro ublesho oting Troubleshooting Your Fujitsu LifeBook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service. Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution: ■ ■ ■ ■ ■ ■ ■ ■ IDENTIFYING THE PROBLEM If you encounter a problem, go through the following procedure before pursuing complex troubleshooting: 1. Turn off your LifeBook. 2. Make sure the AC adapter is plugged into your LifeBook and to an active AC power source. 3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure. 4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure. 5. Turn on your LifeBook. Make sure it has been off at least 10 seconds before you turn it on. 6. Go through the boot sequence. 7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. POINT If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone. CAUTION Do not return a failed LifeBook to your supplier until you have talked to a support representative. Product name Product configuration number Product serial number Purchase date Conditions under which the problem occurred Any error messages that have occurred Hardware configuration Type of device connected, if any See the Configuration Label on the bottom of your LifeBook for configuration and serial numbers. (See figure 2-7 on page 15 for location) SPECIFIC PROBLEMS Using PC-Doctor PC-Doctor is a diagnostic program by PC-Doctor.com, Inc., which comes pre-installed on your LifeBook. If you are an experienced computer user you may find it useful, however, it is intended primarily to help your Fujitsu support representative better serve you. When you call for help, your support representative may ask you to setup your LifeBook for modem operation. You will be told what to do step by step, and then asked to hang up the phone and plug your phone line into the back of your LifeBook. Your support representative will then use the service computer to call your LifeBook and perform diagnostic tests to find the nature of you problem. Messages will be displayed on the screen explaining what is being done and any further instructions that you may need. Using the Troubleshooting Table When you have problems with your LifeBook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your LifeBook. 8. If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8FUJITSU (1-800-838-5487) Fax: 1-901-259-5700 E-mail: [email protected] Web site: http://www.8fujitsu.com. 57 LifeBook C Series – Section Five TROUBLESHOOTING TABLE Problem Page Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 58 DVD/CD-RW/CD-ROM Drive Problems . . . . . page 58 Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 59 Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 60 Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 60 Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 60 Modem Problems . . . . . . . . . . . . . . . . . . . . . . . . . page 60 Problem Problem Page Parallel, Serial and USB Device Problems . . . . . page 61 PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 61 Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 62 Shutdown and Startup Problems . . . . . . . . . . . . page 64 Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 65 Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 66 Possible Cause Possible Solutions Audio Problems There is no sound coming from the built-in speakers. The volume is turned too low. Adjust the volume control on your LifeBook. The software volume control is set too low. Adjust the sound volume control settings in your software, operating system and applications. Headphones are plugged into your LifeBook. Plugging in headphones disables the built-in speakers, remove the headphones. BIOS audio settings are incorrect. Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See BIOS Setup Utility on page 33 for more information) Software driver is not configured correctly. Refer to your application and operating system documentation for help. DVD/CD-RW/CD-ROM Drive Problems LifeBook fails to recognize DVD/CD-RW/CD-ROMs. 58 DVD/CD-RW/CD-ROM is not pushed down onto raised center circle of the drive. Open DVD/CD-RW/CD-ROM tray and re-install DVD/CD-RW/CD-ROM properly. DVD/CD-RW/CD-ROM tray is not latched shut. Push on the front of the DVD/CD-RW/CD-ROM tray until it latches. Setup utility is set to something other than DVD/CDRW/CD-ROM or Auto for the Secondary Master Controller. Revise BIOS settings for the Secondary Master Controller. (See BIOS Setup Utility on page 33 for more information) # Tro ublesho oting Problem LifeBook fails to recognize DVD/CD-RW/CD-ROMs. (continued) Possible Cause Possible Solutions Wrong drive designator was used for DVD/CD-RW/CDROM in the application. Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/ CD-RW/CD-ROM, drive designations are automatically adjusted. Windows DVD/CD-RW/CDROM auto insert notification function is disabled. Start the DVD/CD-RW/CD-ROM from the desktop or application software or re-enable the Windows DVD/CD-RW/CD-ROM auto insert notification function. (See Auto Insert Notification Function on page 46 for more information) DVD/CD-RW/CD-ROM is dirty or defective. Wipe DVD/CD-RW/CD-ROM with a non-abrasive CD cleaning cloth and reinsert. It if still will not work try another DVD/CD-RW/CD-ROM in the drive. The DVD/CD-RW/CDROM Access indicator on the Status Indicator Panel blinks at regular intervals when no DVD/CD-RW/ CD-ROM is in the tray or the DVD/CD-RW/CDROM drive is not installed. The Windows DVD/CD-RW/ CD-ROM auto insert notification function is active and is checking to see if a DVD/CDRW/CD-ROM is ready to run. This is normal. However, you may disable this feature. (See Auto Insert Notification Function on page 46 for more information) The LifeBook fails to AutoPlay a DVD movie. The DVD Player software has not been installed. Locate and install the DVD-ROM Applications CD. You tried to write to a write protected floppy disk. Eject the floppy disk and set it to write enable. (See Floppy Disk Drive on page 43 for more information) Floppy disk is not loaded correctly. Eject floppy disk, check orientation and re-insert. (See Floppy Disk Drive on page 43 for more information) BIOS setup utility states Revise the setup utility Main menu settings to enable Diskette Controller. (See BIOS Setup Utility on page 33 for more information) Floppy Disk Drive Problems You cannot access your floppy disk. Diskette Controller: Disabled. The floppy disk drive may not be properly installed. Remove and re-install your floppy disk drive. Security is set to protect access to floppy disk data. Verify your password and security settings. 59 ! LifeBook C Series – Section Five Problem Possible Cause Possible Solutions The setup utility is incorrectly set for your internal (Primary Master) or optional second hard drive (Primary Slave). Revise BIOS settings to set both Primary Master and Primary Slave correctly. (See BIOS Setup Utility on page 33 for more information) The wrong drive designator was used by an application when a bootable CD-ROM was used to start the LifeBook. Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted. Security is set so your operating system cannot be started without a password. Verify your password and security settings. Hard Drive Problems You cannot access your hard drive. Keyboard or Mouse Problems The built-in keyboard does not seem to work. You have installed an external keyboard or mouse, and it does not seem to work. You have connected an external keyboard or a mouse and it seems to be locking up the system. The LifeBook has gone into Suspend mode. Push the Suspend/Resume button. Your application has locked out your keyboard. Try to use your intergrated pointing device to restart your system. If this fails, turn your LifeBook off using the power switch, wait 10 seconds or more, and then turn it back on. Your external device is not properly installed. Re-install your device. (See Device Ports on page 51 for more information) Your operating system software is not setup with the correct software driver for that device. Check your device and operating system documentation and activate the proper driver. Your operating system software is not setup with the correct software driver for that device. Check your device and operating system documentation and activate the proper driver. Your system has crashed. Try to restart your LifeBook. If that fails, turn off the power using the power switch, wait at least 10 seconds, and then power on. Your memory upgrade module is not properly installed. Remove and re-install your memory upgrade module. (See Memory Upgrade Module on page 49 for more information) You have a memory failure. Check for Power On Self Test (POST) messages. (See Power On Self Test Messages on page 67 for more information) Messages about modem operation are generated by whichever modem application is in use. See your application software documentation for additional information. Memory Problems Your Power On screen, or Main menu of the BIOS setup utility information, does not show the correct amount of installed memory. Modem Problems Messages about modem operation. 60 ! Tro ublesho oting Problem Possible Cause Possible Solutions Parallel, Serial, and USB Device Problems You have installed a parallel port device, a serial port device or a USB device. Your LifeBook does not recognize the device, or the device does not seem to work properly. The device is not properly installed. Remove and re-install the device. (See Device Ports on page 51 for more information) The device may have been installed while an application was running, so your LifeBook is not aware of its installation. Close the application and restart your LifeBook. Your software may not have the correct software driver active. See your software documentation and activate the correct driver. You may have the wrong I/O address selected for your device. See your device documentation and software documentation to determine the required I/O address. Change the settings in the BIOS setup utility. (See BIOS Setup Utility on page 33 for more information) Your device and another device are assigned the same I/O address. Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications. Parallel port is set to output only. Check parallel port setting in the BIOS and set to bi-directional or ECP. The card is not properly installed. Remove and re-install the card. (See PC Cards on page 47 for more information) The card may have been installed while an application was running, so your LifeBook is not aware of its installation. Close the application and restart your LifeBook. Your software may not have the correct software driver active. See your software documentation and activate the correct driver. You may have the wrong I/O address selected for your PC Card device. See your PC Card documentation to determine the required I/O address. Change the settings in the BIOS. (See BIOS Setup Utility on page 33 for more information) Your PC Card device and another device are assigned the same I/O address. Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications. PC Card Problems A card inserted in the PC Card slot does not work or is locking up the system. 61 ! LifeBook C Series – Section Five Problem Possible Cause Possible Solutions Power Failures You turn on your LifeBook and nothing seems to happen. The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter (AC or Auto/ Airline) installed. Check the Status Indicator Panel to determine the presence and condition of the batteries. (See CoolView Display on page 16 for more information) Install a charged battery or a Power adapter. The primary battery is installed but is faulty. Use the Status Indicator panel to verify the presence and condition of the batteries. (See CoolView Display on page 16 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery. The battery or batteries are low. Check the Status Indicator Panel to determine the presence and condition of the batteries. (See CoolView Display on page 16 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery. 62 The power adapter (AC or auto/airline) is not plugged in properly. Verify that your adapter is connected correctly. (See Power Sources on page 31 for more information) The Power adapter (AC or auto/airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter. Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position. The Power adapter (AC or auto/airline) is faulty. Try a different Power adapter or install a charged optional second battery. Power switch is not in the On position. Slide your power switch firmly to the Off position, pause 10 seconds or more and then firmly to the On position. ! Tro ublesho oting Problem Your LifeBook turns off all by itself. Your LifeBook will not work on battery alone. Possible Cause Possible Solutions The power management parameters are set for auto timeouts which are too short for your operating needs. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. You are operating on battery power only and have ignored a low battery alarm until the batteries are all at the dead battery state and your machine has gone into Dead Battery Suspend mode. Install a power adapter and then push the Suspend/ Resume button. (See Power Sources on page 31 for more information) You have a battery failure. Verify the condition of the batteries using the Status Indicator panel, and replace or remove any batteries that are shorted. (See CoolView Display on page 16 for more information) Your power adapter has failed or lost its power source. Make sure the adapter is plugged in and the outlet has power. The installed batteries are dead. Replace the battery with a charged one or install a Power adapter. No batteries are installed. Install a charged battery. The batteries are improperly installed. Verify that the batteries are properly connected by re-installing them. Your installed batteries are faulty. Verify the condition of the batteries using the Status Indicator panel and replace or remove any batteries that are shorted. (See CoolView Display on page 16 for more information) 63 ! LifeBook C Series – Section Five Problem The batteries seem to discharge too quickly. Possible Cause Possible Solutions You are running an application that uses a great deal of power due to frequent hard drive access or DVD/CD-RW/CDROM access, use of a modem card or a LAN PC card. Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible. The power savings features may be disabled. Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs. The brightness is turned all the way up. Turn down the brightness adjustment. The higher the brightness the more power your display uses. The batteries are very old. Replace the batteries. The batteries have been exposed to high temperatures. Replace the batteries. The batteries are too hot or too cold. Restore the LifeBook to normal operating temperature. The Charging icon on the Status Indicator panel will flash when the battery is outside its operating range. Shutdown and Startup Problems The Suspend/Resume button does not work. The system powers up, and displays power on information, but fails to load the operating system. An error message is displayed on the screen during the LifeBook (boot) sequence. 64 The Suspend/Resume button is disabled from the Advanced submenu of the Power menu of the setup utility. Enable the button from the setup utility. You did not hold the button in long enough. Hold the button longer. This may need to be a few seconds if your application is preventing the CPU from checking for button pushes. There may be a conflict with the application software. Close all applications and try the button again. The boot sequence settings of the setup utility are not compatible with your configuration. Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. (See BIOS Setup Utility on page 33 for more information) You have a secured system requiring a password to load your operating system. Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them as accordingly. (See BIOS Setup Utility on page 33 for more information) Internal hard drive was not detected. Use the BIOS setup utility or Primary Master submenu, located within the Main menu, to try to auto detect the internal hard drive. Power On Self Test (POST) has detected a problem. See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. (See Power On Self Test Messages on page 67 for more information) ! Tro ublesho oting Problem Your LifeBook appears to change setup parameters when you start it. Possible Cause Possible Solutions BIOS setup changes were not saved when you made them and exited the BIOS setup utility returning it to previous settings. Make sure you select Save Changes And Exit when exiting the BIOS setup utility. The BIOS CMOS hold-up battery has failed. Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years. Something is pushing on the Closed Cover switch. Clear the Closed Cover switch. (See figure 2-3 on page 9 for location) The LifeBook is set for an external monitor only. Pressing [F10] while holding down the [FN] key allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor. The angle of the display and the brightness settings are not adequate for your lighting conditions. Move the display and the brightness control until you have adequate visibility. The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/ Resume button. (The display may be shut off by Standy mode, Auto Suspend or Video Timeout) The LifeBook turned on with a series of beeps and your built-in display is blank. Power On Self Test (POST) has detected a failure which does not allow the display to operate. Contact your support representative. The display goes blank by itself after you have been using it. The LifeBook has gone into Video timeout, Standby mode, Suspend mode or Hibernation (Save-to-Disk) mode because you have not used it for a period of time. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 33 for more information) Something is pushing on the Closed Cover switch. Check the Closed Cover switch. (See figure 2-3 on page 9 for location) The power management timeouts may be set for very short intervals and you failed to notice the display come on and go off again. Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/ Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout) Video Problems The built-in display is blank when you turn on your LifeBook. 65 !! LifeBook C Series – Section Five Problem Possible Cause Possible Solutions The Built-in Display does not close. A foreign object, such as a paper clip, is stuck between the display and the keyboard. Remove all foreign objects from the keyboard. The Built-in Display has bright or dark spots. If the spots are very tiny and few in number, this is normal for a large LCD display. This is normal; do nothing. If the spots are numerous or large enough to interfere with your operation needs. Display is faulty; contact your support representative. The application display uses only a portion of your screen and is surrounded by a dark frame. You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled. Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 33 for more information) The Display is dark when on battery power. The PMSet default is set on low brightness to conserve power. Press [FN] + [F7] to increase brightness or doubleclick on PMSet battery gauge and adjust Power Control under battery settings. You have connected an external monitor and it does not display any information. Your BIOS setup is not set to enable your external monitor. Try toggling the video destination by pressing [FN] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 33 for more information) Your external monitor is not properly installed. Reinstall your device. (See External Monitor Port on page 53 for more information) Your operating system software is not setup with the correct software driver for that device. Check your device and operating system documentation and activate the proper driver. Your external monitor is not compatible with your LifeBook. See your monitor documentation and the External Monitor Support portions of the Specifications section. Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status. You have connected an external monitor and it does not come on. Miscellaneous Problems An error message is displayed on the screen during the operation of an application. 66 !" Tro ublesho oting POWER ON SELF TEST MESSAGES The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. The most common errors are marked with a #. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance. nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.) *Diskette drive A error or Diskette drive B error Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 33 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative. *Extended RAM Failed at offset: nnnn Extended memory not working or not configured properly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative. nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested. *Failing Bits: nnnn The hex number nnnn This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative. *Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative. *Incorrect Drive A type – run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency. *Incorrect Drive B type – run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency. *Invalid NVRAM media type Problem with NVRAM access. In the unlikely case that you see this message you may have some display problems. You can continue operating but should contact your support representative for more information. *Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative. *Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative. *Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative. *Monitor type does not match CMOS – Run SETUP Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative. #*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard 67 ! LifeBook C Series – Section Five drive may be corrupted and your system may have to be re-installed from your back up media. System BIOS shadowed System BIOS copied to shadow RAM. *Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative. *System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system. *Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative. #*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings. #*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power with the Power Switch and contact your support representative. *Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative. *Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support representative. nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested. *System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your LifeBook. This battery has an expected life of 2 to 3 years. 68 *System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs. nnnn System RAM Passed Where nnnn is the amount of system memory in kilobytes successfully tested. *System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs. UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. !# Tro ublesho oting EMERGENCY DVD TRAY RELEASE If for some reason the eject button fails, you can open the DVD tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out a short distance. MODEM RESULT CODES The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are: ■ ■ ■ ■ ■ ■ ■ ■ ■ OK NO CARRIER NO DIALTONE CONNECT 53000 (Connection complete at 53,000 bps.) ERROR FAX RING (This means an incoming call.) BUSY NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation. RECOVERY CD-ROM Included with your LifeBook are the Emergency Recovery CD and Drivers and Application Restore CD. POINT If you have access to the internet, visit the Fujitsu PC Corporation Support Web site at www.8fujitsu.com to check for the most current information, drives and hints on how to perform recovery and system updates. Restoring Your Pre-installed Software from CD-ROM The Emergency Recovery CD-ROM enables restoration of your LifeBook disk drive contents as they were originally shipped from the factory. Most often this is necessary if files or software programs (only those files/ programs that came pre-installed) become corrupt or accidentally erased. You have two options available when performing recovery: 1. Recover Hard Drive without Format. This choice replaces all the original factory installed files and program structures without eliminating your data files. You will have to re-install any software that was not included with the computer when you bought it, however you data will be intact as long as the installation of the additional programs is performed in the same manner. 2. Format and Recover Hard Drive. This choice removes all the information on the hard disk. If you choose this option, you will lose any software you have installed and any other files you created since you setup your computer. You will have to re-install any software that was not included with the computer when you bought it. POINT It is recommended that you back-up all data files prior to performing either of the recovery options. The Emergency Recovery CD contains the following: ■ A backup copy of the software originally installed on your Fujitsu LifeBook (can only be used on the listed LifeBook models). The Drivers and Application Restore CD contains the following: ■ ■ Sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your LifeBook configuration for use as documented below. Read-me files that provide additional use information for items on this CD-ROM. CAUTION User data and user installed software CAN NOT be recovered from the Emergency Recovery CD. To Run the Emergency Recovery Program To use this portion of the CD-ROM, your LifeBook must Boot up (upon power up or full system reset/restart) from the CD-ROM drive. 1. Insert the Emergency Recovery CD in the CD-ROM drive. 69 " LifeBook C Series – Section Five 2. If your LifeBook is running when you insert the CD, exit your operating system and power down the LifeBook. 3. Start (power up) your LifeBook. 4. At this point, you must either change your BIOS setup configuration through the [F2] key to have the computer boot from the CD-ROM “first” (if you have not previously done so), or you can use the [ESC] key during this boot-up sequence and select the CD-ROM from the menu that will appear. (See BIOS Setup Utility on page 33 for more information) 5. If correctly configured to boot from the Recovery CD-ROM, you will notice your system running a full virus scan of the hard drive and then reach the Emergency Recovery Welcome screen. If this is not what is displayed, check to see that the Recovery CD is installed in the CD-ROM drive and repeat the previous steps, starting with 2. If you received a message “This program may not be used on your computer” you are using the wrong Recovery CD for the model of LifeBook. Contact Fujitsu PC Service and Support to obtain the correct CD. 6. Read the information displayed on the Welcome screen, then click OK. 7. Select one of the two icons displayed in the Emergency Recovery menu and follow the instructions. 8. When recovery is complete, remove the Recovery CD, replace it in its sleeve and store it in a safe location (with your Operating System Manual. 9. Restart your LifeBook. 10. Reset your boot device priority in the BIOS setup as desired. Your LifeBook now has all of the software installed that was included when you received it from the factory. You must now load any programs which you purchased and installed after you received your LifeBook. If you chose the Format and Recover Hard Drive option, you should now restore your data files. If you performed the Recover Hard Drive without Format, your data files will still exist (within their original directory structures). 70 POINT As long as there is no bootable disk in the CD-ROM drive or the floppy disk drive, your LifeBook will boot from the hard drive regardless of the BIOS Boot Device Priority setting. Drivers and Applications Restore CD The Drivers and Application CD can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted. Please refer to installation instructions located in the Drivers and Applications Restore CD. POINT Look for and open files with the extensions.DOC, .PDF and/or .TXT. " 6 Care and Maintenance 71 " LifeBook C Series – Section Six 72 " Care and Maintenance Care and Maintenance If you use your Fujitsu LifeBook carefully, you will increase its life and reliability. This section provides some tips for looking after the LifeBook and its devices. Cleaning your Fujitsu LifeBook ■ Always disconnect the power plug. (Pull the plug, not the cord.) ■ Clean your Fujitsu LifeBook with a damp, lint-free cloth. Do not use abrasives or solvents. ■ Use a soft cloth to remove dust from the screen. Never use glass cleaners. CAUTION Electrical equipment may be hazardous if misused. Operations of this product or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables. Storing your Fujitsu LifeBook If storing your LifeBook for a month or longer, turn your Fujitsu LifeBook off and remove all Lithium ion batteries. ■ ■ Store your Fujitsu LifeBook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your LifeBook. ■ Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between -25ºC (13ºF) and 60ºC (140ºF). FUJITSU LIFEBOOK Caring for your Fujitsu LifeBook ■ Your Fujitsu LifeBook is a durable but sensitive electronic device. Treat it with respect and care. ■ Make a habit of transporting it in a suitable carrying case. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely. ■ Keep it away from food and beverages. ■ If you accidentally spill liquid on your LifeBook: 1. Turn it off. 2. Position it so that the liquid can run out. 3. Let it dry out for 24 hours, or longer if needed. 4. If your LifeBook will not boot after it has dried out, call your support representative. ■ Do not use your Fujitsu LifeBook in a wet environment (near a bathtub, swimming pool). ■ Always use the AC adapter and batteries that are approved for your LifeBook. ■ Avoid exposure to sand, dust and other environmental hazards. ■ Do not expose your Fujitsu LifeBook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your LifeBook. ■ Keep the covers closed on the connectors and slots when they are not in use. ■ Do not put heavy or sharp objects on the computer. ■ If you are carrying your Fujitsu LifeBook in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid. ■ Never position your LifeBook such that the DVD drive is supporting the weight of the LifeBook. ■ Do not drop your Fujitsu LifeBook. ■ Do not touch the screen with any sharp objects. Traveling with your Fujitsu LifeBook Do not transport your Fujitsu LifeBook while it is turned on. ■ ■ Do not check your Fujitsu LifeBook as baggage. Carry it with you. ■ Always bring your System Recovery CD that came with your Fujitsu LifeBook when you travel. If you experience system software problems while traveling, you may need it to correct any problems. ■ Never put your Fujitsu LifeBook through a metal detector. Have your LifeBook hand-inspected by security personnel. You can however, put your Fujitsu LifeBook through a properly tuned X-ray machine. To avoid problems, place your LifeBook close to the entrance of the machine and remove it as soon as possible or have your LifeBook hand-inspected by security personnel. Security officials may require you to turn your LifeBook On. Make sure you have a charged battery on hand. ■ When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine. ■ Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent. 73 " LifeBook C Series – Section Six Outlet Type Location United States, Canada, parts of Latin America, Japan, Korea, the Philippines, Taiwan Russia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South Asia Mexico, United Kingdom, Ireland, Malaysia, Singapore, parts of Africa China, Australia, New Zealand Increasing Battery Life ■ Power your Fujitsu LifeBook through the AC or optional auto/airline adapter whenever possible. ■ If your Fujitsu LifeBook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery. ■ Keep brightness to the lowest level comfortable. ■ Set the power management for maximum battery life. ■ Put your Fujitsu LifeBook in Suspend mode when it is turned on and you are not actually using it. ■ Limit your DVD access. ■ Disable the Windows CD auto insert notification function. ■ Always use fully charged batteries. ■ Eject PCMCIA cards when not in use. FLOPPY DISKS AND DRIVES Caring for your Floppy Disks ■ Avoid using the floppy disks in damp and dusty locations. ■ Never store a floppy disk near a magnet or magnetic field. ■ Do not use a pencil or an eraser on a disk or disk label. ■ Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC). ■ Do not touch the exposed part of the disk behind the metal shutter. BATTERIES Caring for your Batteries ■ Always handle batteries carefully. ■ Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire. ■ Do not drop, puncture, disassemble, mutilate or incinerate the battery. ■ Recharge batteries only as described in this manual and only in ventilated areas. ■ Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life. ■ Do not leave a battery in storage for longer than 6 months without recharging it. 74 Caring for your Floppy Disk Drive ■ To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material. ■ Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC). ■ Keep the floppy disk drive out of direct sunlight and away from heating equipment. ■ Avoid storing the floppy disk drive in locations subject to shock and vibration. ■ Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk. ■ Never disassemble or dismantle your floppy disk drive. " Care and Maintenance DVDs AND CDs Caring for your DVDs and CDs DVDs and CDs are precision devices and will function reliably if given reasonable care. will provide specific information, but you should pay attention to the following points: ■ Always store your DVD/CDs in its case when it is not in use. To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed in your LifeBook. ■ Always handle DVD/CDs by the edges and avoid touching the surface. Avoid prolonged exposure to direct sunlight or excessive heat. ■ Keep the cards dry. ■ Avoid storing any DVD/CDs in extreme temperatures. ■ ■ Do not bend DVD/CDs or set heavy objects on them. Do not flex or bend the cards, and do not place heavy objects on top of them. ■ Do not spill liquids on DVD/CDs. ■ Do not force cards into the slot. ■ Do not scratch DVD/CDs. ■ Avoid dropping cards, or subjecting them to excessive vibration. ■ Do not put a label on DVD/CDs. ■ Do not get dust on DVD/CDs. ■ Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen. ■ If a DVD/CD is subjected to a sudden change in temperature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry DVD/CDs. ■ If a DVD/CD is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge. ■ ■ Caring for your DVD Drive Your DVD drive is durable but you must treat it with care. Please pay attention to the following points: ■ The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on. ■ Avoid using or storing the drive where it will be exposed to extreme temperatures. ■ Avoid using or storing the drive where it is damp or dusty. ■ Avoid using or storing the drive near magnets or devices that generate strong magnetic fields. ■ Avoid using or storing the drive where it will be subjected to shock or vibration. ■ Do not disassemble or dismantle the DVD drive. PC CARDS Caring for your PC Cards PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Card 75 "! LifeBook C Series – Section Six 76 "" 7 Specifications 77 " LifeBook C Series – Section Seven 78 "# Specifications Specifications CONFIGURATION LABEL Your Fujitsu LifeBook contains a configuration label located on the bottom of your LifeBook. (See figure 2-7 on page 15 for location) This label contains specific information regarding the options you’ve chosen for your LifeBook. Following is an example label and information on how to read your own configuration label. This section provides the hardware and environmental specifications for your Fujitsu LifeBook. Specifications of particular configurations will vary. Part Number Configuration ID Device o FPC070153 o CPXXXXXXXXXXXX C-6577, PIII 750, 14T, 128M, 98, 20G, DVD Model Processor Memory Screen Size Hard Drive Operating System Figure 7-1 Configuration Label Models # C-6577 C-6556 C-6547 Processor 750 MHz Pentium III with SpeedStep Technology 650 MHz Pentium III with SpeedStep Technology 600 MHz Pentium III with SpeedStep Technology Display 14.1" XGA TFT 14.1" XGA TFT 14.1" XGA TFT Memory 128MB 64MB 64MB Hard Drive 20GB 15GB 12GB DVD/CD Built-in DVD Built-in DVD Built-in DVD Floppy Disk Drive Built-in Floppy Disk Drive Built-in Floppy Disk Drive Built-in Floppy Disk Drive Modem 56K* V.90 support 56K* V.90 support 56K* V.90 support Wireless IR Mouse Included Optional Optional Note: For a detailed list of options available for your LifeBook, visit the Fujitsu web site at: www.fujitsupc.com or call FPCDIRECT (1-877-372-3473). * Actual speeds over U.S. telephone lines vary and are less than 56Kbps due to the current FCC regulations and line conditions. The internal modems on all Fujitsu LifeBooks from Fujitsu PC Corporation are only qualified for use with telephone systems inside the United States and Canada and may not operate in other countries. 79 LifeBook C Series – Section Seven MICROPROCESSOR Latest high-speed Intel mobile microprocessor. MEMORY System Memory 128MB or 64MB, expandable up to 192MB SDRAM. Touch pad pointing device Scroll button Communications Modem: Internal V.90 standard 56K* fax/modem (ITU V.90, 56K data, 14.4K fax.) * Actual speeds over U.S. telephone lines vary and are less than 56Kbps due to the current FCC regulations and line conditions. The internal modems on all Fujitsu LifeBooks from Fujitsu PC Corporation are only qualified for use with telephone systems inside the United States and Canada and may not operate in other countries. Cache Memory 256 KB on-die L2 cache. BIOS Memory 512KB Flash ROM. 256 Bytes CMOS RAM with back-up battery. VIDEO Built-in color flat-panel TFT active matrix LCD display with simultaneous display capability. LifeBook Application Panel CoolView Display. Application Launcher and Audio CD Player. Video Color and Resolution 14.1" XGA TFT ■ Internal: 1024 x 768 pixel resolution, 256K colors. ■ External: 1600 x 1200 pixel resolution, 16M colors. ■ Simultaneous Video Theft Prevention Lock Lock slot for use with physical restraining security systems. The locking system by Kensington is recommended. Video RAM 8MB Embedded SDRAM. Video Zoomed Video support via PC Card Slot 1. AUDIO ■ ■ ■ ■ ■ ■ SoundBlaster Pro-compatible 32-bit stereo PCM/FM sound chip. Spatializer 3D-Stereo multiple speaker effect support. Stereo headphone jack, 1 Vrms, or less, minimum impedance 32 Ohms. Stereo line in jack, 880 mVrms or less, minimum impedance 10K Ohms. Mono microphone jack, 125 mVp-p or less, minimum impedance 10K Ohms. Two built-in speakers, 28 mm diameter (Stereo). Pre-Installed Software ■ Microsoft Windows 98 Second Edition ■ Microsoft Internet Explorer ■ Microsoft Press Interactive Training for Windows 98 ■ Microsoft Works 2000 ■ Quicken 2000 ■ LapLink 2000 by LapLink.com, Inc. ■ PC-Doctor by PC-Doctor.com, Inc. ■ PMSet 98 by Fujitsu Limited. ■ McAfee.com, Inc. ActiveShield ■ McAfee.com Clinic on-line coupon ■ Adobe Acrobat Reader by Adobe Systems, Inc. ■ Netscape Communicator by Netscape Communications Corporation. ■ DVD Player ■ LifeBook Application Panel ■ Intel SpeedStep utility DEVICE PORTS MASS STORAGE DEVICE OPTIONS Floppy Disk Drive Built-in 3. 5" Floppy Disk Drive, which accommodates 1.44MB or 720KB floppy disks. ■ ■ Hard Drive 20GB, 15GB, or 12GB fixed hard drive. ■ DVD Drive 8x DVD drive ■ FEATURES ■ Integrated Pointing Device 80 Combination PC Card slot for one Type III/two Type II cards: PCMCIA Standard 2.1 with CardBus support; Zoomed Video support via Slot 1. One 6-pin mini DIN PS/2 compatible connector, for external keyboard, external mouse or external numeric keypad. One 25-pin D-SUB two-way Centronics type connector for parallel input/output devices; Bi-directional, output only or ECP. One 15-pin D-SUB connector for VGA external monitor (see Display specifications). One 9-pin D-SUB connector for RS-232C serial input/output devices. Specifications ■ ■ ■ ■ ■ ■ ■ ■ Two connectors for USB (Universal Serial Bus) input/output devices. One 1394 connector One 25-pin special connector for external floppy disk drive connection. One modular modem (RJ-11) connector. One stereo headphone jack. (See Audio specifications) One mono microphone jack. (See Audio specifications) One stereo line-in jack. (See Audio specifications) One S-Video connector KEYBOARD Built-in keyboard with all functions of 101 key PS/2 compatible keyboards. ■ Total number of keys: 87. ■ Function keys: 12, F1 through F12. ■ Feature extension key: Fn. ■ Three Windows keys: two Start keys and one application key ■ Key pitch: 19 mm. ■ Key stroke: 3 mm. ■ Built-in touchpad and scroll button ■ Built-in Palm Rest. DIMENSIONS AND WEIGHT Overall Dimensions 12.20" x 11.40" x 1.82" Weights Approximately 7.3 lbs. ENVIRONMENTAL REQUIREMENTS Temperature Operating: 5° to 35° C (41° to 95° F). Non-operating: –15° to 60° C (5° to 140° F). Humidity Operating: 20% to 85%, relative, non-condensing. Non-operating; 8% to 85%, relative, non-condensing. Altitude Operating: 10,000 feet (3,048 m) maximum. External Keyboard Support PS/2 compatible. External Numeric Keypad Support PS/2 compatible. External Mouse Support PS/2 compatible. POWER Batteries One 9-cell Lithium ion battery, rechargeable, 10.8V, 3600 mAh. Bridge Battery Your Fujitsu LifeBook comes equipped with a bridge battery. A bridge battery allows a charged Lithium ion battery to be replaced without shutting down the system. The bridge battery capacity is not large and can vary with the condition or your LifeBook, so you will have 3 minutes at the most to make the change. AC Adapter Autosensing 100-240V AC, 53W, supplying 16V DC to the LifeBook, Fujitsu Model FPCAC08 which includes an AC cable. Power Management Conforms to ACPI (Advanced Configuration and Power Interface). Electro-Static Discharge (ESD) 9 kV. 81 LifeBook C Series – Section Seven 82 8 Glossary 83 LifeBook C Series – Section Eight 84 Glossary Glossary in specially structured ways to make your overall data handling time faster. 1394 A fast external bus that allows transfer rates of up to 400 Mbps. CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture. AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook. ACPI A power management specification that allows the operating system to determine the amount of power given to each connected device. Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen. APM Advanced Power Management. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook. BIOS Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware. Bit An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0). bps An abbreviation for bits per second. Used to describe data transfer rates. Boot To start-up a computer and load its operating system from disk, ROM or other storage media into RAM. Bus An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used CD-ROM Compact disc read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading. CMOS RAM Complementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate. COMM Port Abbreviation for communication port. This is your serial interface connection. Command An instruction which you give your operating system. Example: run a particular application or format a floppy disk. Configuration The combination of hardware and software that makes up your system and how it is allocated for use. CRT Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam. Data The information a system stores and processes. DC Direct current. A voltage or current that does not fluctuate periodically with time. Default Value A pre programmed value to be used if you fail to set your own. DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette. 85 ! LifeBook C Series – Section Eight Disk Drive The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk. Hexadecimal A decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in hexadecimal = 00101111 in binary = 47 in decimal. Diskette A floppy disk in a hard housing with a shutter. I/O Input/Output. Data entering and leaving your LifeBook in electronic form. DMA Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action. DMI Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals. DOS Disk Operating System (MS-DOS is a Microsoft Disk Operating System). Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment. ECP Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices. I/O Port The connector and associated control circuits for data entering and leaving your LifeBook in electronic form. IDE Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. IR An abbreviation for infrared. IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier. IRQ Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. KB Kilobyte. ESD Electro-Static Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day. LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves. Extended Memory All memory more than the 640KB recognized by MS-DOS as system memory. LCD Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid. FCC Federal Communication Commission. Floppy Disk A spinning platter of magnetic data storage media which is highly flexible. GB Gigabyte. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. 86 Lithium ion Battery A type of rechargeable battery which has a high powertime life for its size and is not subject to the memory effect as Nickel Cadmium batteries. LPT Port Line Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports. " Glossary MB Megabyte. organization that sets standards for add-in cards for personal computers. Megahertz 1,000,000 cycles per second. Peripheral Device A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM. Memory A repository for data and applications which is readily accessible to your LifeBook CPU. MHz Megahertz. MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers. Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line. Monaural A system using one channel to process sound from all sources. MPU-401 A standard for MIDI interfaces and connectors. NTSC National TV Standards Commission. The standard for TV broadcast and reception for the USA. Operating System A group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of microprocessor in order to produce the desired results from that particular equipment. PAL Phase Alternating Line. The standard for TV broadcast and reception for Europe. Parallel Port A connection to another device through which data is transferred as a block of bits simultaneously with a wire for each bit in the block and with other wires only for control of the device not for transfer of data. Partition A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly. PCMCIA PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an Pitch (keyboard) The distance between the centers of the letter keys of a keyboard. Pixel The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear. POST Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your LifeBook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. Program An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it. PS/2 An IBM series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors. RAM Random Access Memory. A hardware component of your LifeBook that holds binary information (both program and data) as long as it has the proper power applied to it. RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools. Reset The act of reloading the operating system. A reset erases all information stored in RAM. Restart See Reset. Resume To proceed after interruption. In your LifeBook this refers to returning to active operation after having been in one of the suspension states. ROM Read Only Memory. A form of memory in which information is stored by physically altering the material. Data 87 LifeBook C Series – Section Eight stored in this way can not be changed by your LifeBook and does not require power to maintain it. SVGA Super VGA. SDRAM Synchronous Dynamic Random Access Memory. S-Video Super Video. A component video system for driving a TV or computer monitor. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data. Shadow RAM A technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random Access Memory) for access during actual operation. RAM is much faster to access than ROM, however ROM contents are not lost when power is removed. Shadowing allows permanently stored information to be rapidly accessed. SMART Self-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides nearterm failure predictions for hard drives. When SMART is enabled the hard drive monitors pre-determined drive attributes that are susceptible to degradation over time. If a failure is likely to occur, SMART makes a status report available so that the LifeBook can prompt the user to back up the data on the drive. Naturally not all failures are predictable. SMART predictability is limited to those attributes which the drive can self-monitor. In those cases where SMART can give advance warning, a considerable amount of precious data can be saved. System Clock An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to provide time of day and date. TFT Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. UL Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices. VGA Video Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers. VRAM Video Random Access Memory. A memory dedicated to video display data and control. WFM Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility. SRAM Static random access memory. A specific technology of making RAM which does not require periodic data refreshing. Write Protect Prevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or directory of floppy diskette or hard drive. Status Indicator A display which reports the condition of some portion of your hardware. On your LifeBook this is an LCD screen just above the keyboard. XGA Extended VGA. Stereo (audio) A system using two channels to process sound from two different sources. Stroke (keyboard) The amount of travel of a key when it is pressed from resting to fully depressed. Suspend To make inoperative for a period of time. Your LifeBook uses various suspension states to reduce power consumption and prolong the charge of your battery. 88 Zip Drive A 100MB read/write removable media disk drive. Zoomed Video A PC Card port which allows LifeBook PCs to deliver full screen broadcast quality video through third party PC Cards, including TV tuners, video capture, and MPEG full-motion video. # Index Index A Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 85 plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Application See Pre-installed Software Auto Insert Notification . . . . . . . . . . . . . . . . . . . . . . . 46 Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . 31, 85 Disk care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 ejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 B Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . 36 dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 lithium ion battery . . . . . . . . . . . . . . . . . . . . . . 41, 86 low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 64 recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 power management . . . . . . . . . . . . . . . . . . . . . . . . .32 BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 C Cache Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 CD-ROM care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 COMM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Drivers and Application CD . . . . . . . . . . . . . . . . . . . .70 DVD drive control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 player software . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 DVD Player Control Panel . . . . . . . . . . . . . . . . . . . . . .45 using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 DVD Player Software . . . . . . . . . . . . . . . . . . . . . . . . . .44 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 un-installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 DVD/CD-ROM access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 E Emergency Recovery CD . . . . . . . . . . . . . . . . . . . . . . .69 D Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 DC Output Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Extended Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 External Monitor Port . . . . . . . . . . . . . . . . . . . . . . . . .53 # LifeBook C Series F Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . .60 Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . 43, 59 care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Fujitsu LifeBook care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . .69 Function Key F10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N 20 20 20 20 20 Modem Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Mouse See ErgoTrac and/or Touchpad Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 P Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 61, 87 PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 H Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 PC Cards installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 I Pointing Device See Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Power AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . .31 failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 K Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 60 cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Power Management . . . . . . . . . . . . . . . . . . . . . . . .36, 37 Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 L LifeBook Application Panel CD player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 25 LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 selector switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 R Recovery CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 M Memory capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . extended . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . .28 manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 restoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 tutorials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34, 35 50 50 49 50 50 49 Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 S Save-to-Disk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 # Index SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 61, 88 Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Software See Pre-installed Software Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Stereo Line-in Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Suspend/Resume Button . . . . . . . . . . . . . . . . . . . 36, 64 T Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 U Universal Serial Bus Port . . . . . . . . . . . . . . . . . . . . . . 51 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 61 W Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 end user license agreement . . . . . . . . . . . . . . . . . . . 34 Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Wireless Infrared Mouse Port . . . . . . . . . . . . . . . . . . 52 # LifeBook C Series
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement