Harbor Freight Tools 20 ton Air Hydraulic Bottle Jack Product manual

Safety ......................................................... 2

Setup .......................................................... 7

Operation ................................................... 10

Table of contents

Maintenance .............................................. 12

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SyMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMpORTANT SAFETy INSTRUcTIONS

INSTRUcTIONS pERTAINING TO A RISK OF FIRE,

ELEcTRIc SHOcK, OR INJURy TO pERSONS

WARNING – When using tools, basic precautions should always be followed, including the following:

To reduce the risk of injury to persons, read all the instructions before using the tool.

Work Area

1. Keep the work area clean and well lighted.

Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons.

2. Keep bystanders, children, and visitors away

while operating the tool. Distractions are able to result in the loss of control of the tool.

Page 2 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

personal Safety

1. Stay alert. Watch what you are doing and use common sense when operating the tool.

Do not use the tool while tired or under the

influence of drugs, alcohol, or medication.

A moment of inattention while operating the tool increases the risk of injury to persons.

2. Dress properly. Do not wear loose clothing or jewelry. contain long hair.

Keep hair, clothing, and gloves away from

moving parts. Loose clothes, jewelry, or long hair increases the risk of injury to persons as a result of being caught in moving parts.

3. Avoid unintentional starting. Be sure the switch is off before connecting to the air supply.

Do not carry the tool while touching the switch or connect the tool to the air supply with the switch on.

4. Do not overreach.

Keep proper footing and balance at all times.

Proper footing and balance enables better control of the tool in unexpected situations.

5. Use safety equipment.

A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions.

6.

7.

Always wear eye protection.

Wear ANSI-approved safety goggles.

Always wear hearing protection

when using the tool.

Prolonged exposure to high intensity noise is able to cause hearing loss.

Tool Use and care

1. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed.

2. Do not use the tool if the switch does not turn the

tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the tool from the air source before making any adjustments, changing

accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool unintentionally. Turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position before leaving the work area.

4. Store the tool when it is idle out of reach

of children and other untrained persons.

A tool is dangerous in the hands of untrained users.

5. Maintain the tool with care. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control.

6. check for misalignment or binding of moving parts, breakage of parts, and any other condition

that affects the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

There is a risk of bursting if the tool is damaged.

Service

1. Tool service must be performed only by qualified repair personnel.

2. When servicing a tool, use only identical replacement parts. Use only authorized parts.

3. Use only the lubricants supplied with the tool or specified by the manufacturer.

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 3

Air Source

1. Never connect to an air source that is

capable of exceeding 200 psi.

Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons.

Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range.

2. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source

for the tool. Such gases are capable of explosion and serious injury to persons.

SAVE THESE INSTRUcTIONS.

Symbols and Specific Safety Instructions

Symbol Definitions

Symbol

n o

property or statement

No-load speed

.../min

Revolutions or reciprocation per minute

pSI

Pounds per square inch of pressure

ft-lb

Foot-pounds of torque

cFM

Cubic Feet per Minute flow

ScFM

Cubic Feet per Minute flow at standard conditions

NpT

National pipe thread, tapered

Symbol property or statement

NpS

National pipe thread, straight

WARNING marking concerning Risk of Eye Injury.

Wear ANSI-approved eye protection.

WARNING marking concerning Risk of

Hearing Loss. Wear hearing protection.

WARNING marking concerning

Risk of Respiratory Injury. Wear

NIOSH-approved dust mask/respirator.

WARNING marking concerning

Risk of Explosion.

Page 4 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

Specific Safety Instructions

1. Lifting device only. Immediately after lifting, support the vehicle with appropriate means.

2. Keep clear of load while lifting and lowering.

3. Lower load slowly.

4. Do not use for aircraft purposes.

5. Apply parking brake and chock tires before lifting vehicle.

6. Lift vehicle only at manufacturer-recommended locations.

7. Bleed the hydraulic system before its initial use.

8. When lifting only one wheel, make sure to support load immediately with one jack stand

(not included) placed under side of vehicle being lifted. Align saddle of jack stand directly under vehicle’s seam or recommended lifting point.

9. When lifting entire front end or rear end of vehicle, make sure to support load immediately with two jack stands. Align saddles of jack stands directly under vehicle’s frame or recommended lifting points. Also, make sure jack stands are adjusted at the same height.

10. Do not use Bottle Jack with the vehicle’s engine running. When running, the vehicle’s engine produces carbon monoxide, a colorless, odorless, toxic gas that, when inhaled, can cause serious personal injury or death.

11. Keep hands and feet away from all moving parts of the Bottle Jack when applying or releasing a load. Keep people and animals at a safe distance when using the Bottle Jack.

12. Do not allow anyone in vehicle when using Bottle Jack.

13. Do not use Bottle Jacks to lift both ends of a vehicle at the same time.

14. Before lowering the Bottle Jack, make sure tool trays, jack stands, and all other tools and equipment are removed from under the vehicles.

15. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

16. WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm).

(California Health & Safety code § 25249.5, et seq.)

17. Obey the manual for the air compressor used to power this tool.

18. Install an in-line shutoff valve to allow immediate control over the air supply in an emergency, even if a hose is ruptured.

19. Use this tool with both hands only. Using tools with only one hand can result in loss of control.

SAVE THESE INSTRUcTIONS.

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 5

Functional Description components and controls

Air Inlet

Throttle

Lever

Release Valve

Release Valve

Figure A

Screw Extension

(inside Ram)

Handle Bracket

Jack Handle

Screw Extension

(inside Ram)

Handle Bracket

Jack Handle

Throttle Lever

Air Inlet

Page 6 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

Initial Tool Set Up/Assembly

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Air Supply

TO pREVENT SERIOUS INJURy FROM EXpLOSION:

Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool.

1. Incorporate a filter, regulator with pressure gauge, in-line shutoff valve, and quick coupler for best service, as shown on Figure B on page

8 and Figure C on page 9. An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly.

4. Close the in-line shutoff valve between the compressor and the tool.

5. Turn on the air compressor according to the manufacturer's directions and allow it to build up pressure until it cycles off.

2. Attach an air hose to the compressor's air outlet.

Connect the air hose to the air inlet of the tool.

6. Adjust the air compressor's output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool's maximum air pressure at any time.

Adjust the pressure gradually, while checking the air output gauge to set the right pressure range.

Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components.

The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

7. Inspect the air connections for leaks.

Repair any leaks found.

3. Turn the tool's throttle or switch to the off position; refer to Operation section for description of controls.

8. If the tool will not be used at this time, turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position to prevent accidental operation.

purging Air From Hydraulic System

Note: Before first use, the hydraulic ram may

need to be purged. Some air may intrude in the hydraulic system due to movement during shipping.

Air bubbles can become trapped inside the hydraulic system, thereby reducing the efficiency of the Jack.

Purge air from the system if efficiency drops.

1. Place the slotted end of the Jack Handle over the

Release Valve and turn 1-1/2 turns counterclockwise.

2. Remove the Oil Filler Plug on the side of the Jack Reservoir.

3. Rapidly pump the Handle several times to purge air from the hydraulic system.

4. Use the Handle to turn the Release

Valve screw clockwise until snug.

5. Top off Jack Reservoir with a high quality hydraulic jack oil.

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 7

Lubricated Tools Non-lubricated Tools

Page 8 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

Lubricated Tools

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 9

Operating Instructions

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Inspect tool before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use tool until repaired.

Tool Set Up

TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION:

Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures.

TO pREVENT SERIOUS INJURy:

Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards.

Before Use

1. Park vehicle on a flat, level, solid, surface safely away from oncoming traffic.

2. Turn off the vehicle’s engine.

3. Place the vehicle’s transmission in “PARK” (if automatic) or in its lowest gear (if manual).

Set the vehicle’s emergency brake.

4. Chock the wheels that are not being lifted.

Workpiece and Work Area Set Up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children or pets to prevent distraction and injury.

2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage.

The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

Page 10 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

General Operating Instructions

This is an air-actuated hydraulic bottle jack. The air motor is air pressure activated and drives the hydraulic jack.

In the event no air pressure is available, a standard hydraulic piston assembly is provided for hand jacking.

Note: Safety shutoff prevents lifting in excess of rated load.

1. Position the Jack on a solid level surface that can withstand the weight of the jack and the load which will be lifted.

2. Be sure the load is balanced on the jack.

Properly rated jack stands (not included) positioned under the weight provide a good safety precaution against the possibility of the load toppling.

3. Be sure that the jack is positioned at a proper lift point on the item to be lifted. Using appropriate lift points avoid possible damage to the item.

4. Rotate the Screw Extension on the Ram until it contacts the underside of the load to be lifted.

Screwing counterclockwise raises the extension, screwing clockwise lowers the extension.

5. Engage the notch on the end of the Jack Handle onto the Release Valve. Turn the Release Valve slightly clockwise to ensure that the valve is closed. The jack will not lift if the valve is open.

6. Operation a. Pneumatic Operation: Connect a pressurized air source to the Air Inlet then squeeze the

Throttle Lever on the Air Valve to raise the load.

b. Manual Operation: Insert the end of the Jack Handle into the Handle

Bracket and pump up and down.

7. Support the load using jack stands (not included) or other means to support the weight.

Do not leave the load on the jack for an extended period of time. Damage to the jack or personal or property injury may result.

8. To lower the item, first use the Jack to lift the item slightly and remove the jack stands.

9. Engage notches in the end of the Jack Handle onto the Release Valve. Turn the valve approximately 1/4 turn counterclockwise to lower the load. When the load is lowered, turn the

Release Valve clockwise to stop the motion.

10. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil to the airline connection before use. Add a few drops more after each hour of continual use.

11. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool.

cAUTION! TO pREVENT INJURy FROM

TOOL OR AccESSORy FAILURE:

Do not exceed the tool's

maximum air pressure rating.

If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required.

12. To prevent accidents, turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/ or turn the switch to its off position after use.

Clean external surfaces of the tool with clean, dry cloth, and apply a thin coat of tool oil.

Then store the tool indoors out of children's reach.

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 11

User-Maintenance Instructions

procedures not specifically explained in this manual must be performed only by a qualified technician.

TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION:

Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures.

TO pREVENT SERIOUS INJURy FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use.

cleaning, Maintenance, and Lubrication

Note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated tool.

1. BEFORE EAcH USE, inspect the general condition of the tool. Check for:

• loose hardware or housing,

• misalignment or binding of moving parts,

• cracked or broken parts, and

• any other condition that may affect its safe operation.

2. Daily - Air Supply Maintenance:

Every day, maintain the air supply according to the component manufacturers' instructions.

Drain the moisture filter regularly.

Performing routine air supply maintenance will allow the tool to operate more safely and will also reduce wear on the tool.

3. Quarterly (every 3 months) –

Tool Disassembly, cleaning, and Inspection:

Have the internal mechanism cleaned, inspected, and lubricated by a qualified technician.

4. Periodically check the air and hydraulic fittings for leaks. Repair if any leak is detected.

5. Periodically lubricate all moving points of the Jack.

6. The Hydraulic Ram should be kept clean, free of dirt and water, and protected from corrosion.

7. OIL REPLACEMENT: a. Place Jack in an upright position.

b. Completely lower the Ram.

c. Remove the Filler Plug and keep it clean.

d. Fill Reservoir with high-quality hydraulic jack oil to the lower rim of the fill hole.

e. Purge air from the hydraulic system as previously described on Purging Air From

Hydraulic System on page 7.

f. Top off with more hydraulic oil.

g. Replace Filler Plug.

Page 12 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

Troubleshooting

1. If the Jack fails to lift, or fades under load, first check that the Release Valve is closed. Engage the notches at the end of the Jack Handle onto the Release Valve and turn clockwise. Check to see if this has solved the problem.

2. Next check to see if there are any leaks in the air system. Examine all connections and valves to see if there is a leak. If so, have a qualified service technician repair the connection or replace the faulty part.

3. Check to see if there are any leaks in the hydraulic system. Leaks will produce visible hydraulic fluid at the separation. If there are any leaks, have a qualified repair technician tighten, repair or replace any leaking components.

4. Air in the hydraulic system will cause the jack to fade. If no leaks are detected, purge the hydraulic system to remove any trapped air. SeePurging Air From Hydraulic System on page 7.

5. The Air pump mechanism may be stuck. To remedy this, open the release valve, and operate the air lever fully.

6. If none of these troubleshooting options solves the problem, it is possible that the seals of the jack have been damaged by overloading, dirt on the ram or other environmental factors. Have a qualified service technician inspect the Jack for faults and possible repair. See below for more troubleshooting tips and information.

To prevent Serious Injury:

Use caution when troubleshooting a malfunctioning jack. Stay well clear of the supported load.

Completely resolve all problems before use. If the solutions presented in the Troubleshooting guide do not solve the problem, have a qualified technician inspect and repair the jack before use.

After the jack is repaired: Test it carefully without a load by raising and lowering it fully, checking for proper operation, BEFORE RETURNING THE JACK TO OPERATION.

DO NOT USE A DAMAGED OR MALFUNcTIONING JAcK!

pOSSIBLE SyMpTOMS

Jack will not lift at its weight capacity

Saddle lowers under load

Pump stroke feels spongy

Saddle will not lift all the way

Handle moves up when jack is under load

Oil leaking from filler plug pROBABLE SOLUTION

(Make certain that the jack is not supporting a load while attempting a solution.)

X

X

X

X

X

X X

X

X

Check that Release Valve is fully closed.

Bleed air from the system.

Valves may be blocked and may not close fully. To flush the valves:

1. Lower the Saddle and securely close the Release Valve.

2. Manually lift the saddle several inches.

3. Open the release valve and force the saddle down as quickly as possible.

Jack may be low on oil.

Check the oil level and refill if needed.

Jack may require bleeding

- see Purging Air From

Hydraulic System on page 7.

Unit may have too much hydraulic oil inside, check fluid level and adjust if needed.

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 13

parts List and Diagram parts List and Assembly Diagram for Item #95553

part Description Qty

1 Base

2 Ball

3 Seal

4 Release Valve

5 Ball Cup

6 Spring

7 Spring

8 Screw

9 Nylon Ring

10 Cylinder

11 O-Ring

12 Cup Seal

13 Ram

13.1 Extension Screw

14 Packing

15 Reservoir

1

1

1

1

1

1

1

1

1

2

2

1

1

1

1

6 part Description Qty

16 Filler Plug

17 Nylon Ring

18 Top Nut

19 O-Ring

20 Spring Plate

21 Return Spring

22 Eye Bolt

23 Nut

24 Lock Washer

25 Washer

26 Pump Cylinder

27 O-Ring

28 Nylon Ring

29 Backup Ring

30 Piston

31 Pin

1

3

1

1

1

1

2

2

2

2

1

2

1

1

1

1 part Description Qty

32 R-Pin

33 Connector

34 Handle Bracket

35 Ball

36 Ball Cup

37 Spring

38 Screw

39 O-Ring

40 Screw

41 Plastic Cup

42 Air Motor

43 Air Hose

44 Air Valve

45 Handle

1

1

1

1

1

2

1

1

1

1

1

1

3

1

Page 14 For technical questions, please call 1-800-444-3353.

Item 69593/69642/95553

parts List and Assembly Diagram for Items #69593 and #69642

part Description

1.1 Hose Connector

1.2 Connecting Nut

1.3 Air Filter

1.4 "O"Ring 18×2.4

1.5 Connector

1.6 Valve Body

1.7 Spring

1.8 Packing

1.9 Throttle

1.10 "O"Ring 3×1.6

1.11 "O"Ring 18×2.4

1.12 Nut

1.13 Lever

1.14 Lever Pin

1.15 Hose Connector

1.16 Hose Band

1.17 Lock Lever

2 Air Hose

3 Connector

4 Air Hose

5 Handle Upper

6 Handle Lower

Qty

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1 part Description Qty

7 Plunger

8 Shaft Pin

9 Cotter Pin

10 Pump Plunger

11 Pump Plunger Retainer 1

12 "O"Ring

13 Dust Proof Ring

14 Pump Reservoir

15 Copper Washer

16 Steel Ball 6

17 Connecting Rod

18 Release Valve Screw

19 Release Valve Seal

20 Steel Ball 6.35

21 Pin

22 Valve Spring

23 Filler Plug

24 Screw

25 Plug Screw

26 Plunge Washer

27 Overload Valve Screw 1

28 Safety Valve Spring

1

1

2

1

2

1

3

1

1

3

1

1

1

1

6

1

1

1

1

1 part Description

29 Overload Valve

30 Filter Net

31 Spring Washer 8

32 Nut 8

33 Bolt M8×35

34 Base

35 Plug Screw

36 Cylinder Bottom Seal

37 Reservoir

38 Packing

39 Cylinder

40 Steel Ball Retainer

41 Cylinder Top Seal

42 "O"Ring

43 Top Nut

44 Extension Screw

45 "O"Ring

46 "O"Ring Returner

47 Ram Header

48 Ram

49 Spring

50 Spring Plate

Qty

1

1

1

1

1

2

1

1

4

1

2

1

2

2

1

2

1

1

1

1

2

1

50

42

43

49

44

5

49

33

32

31

41

23

33

32

31

48

47

6

37

36

46

45

39

38

40

7

10 17

11

12

13

14

15

16

30

24 22

20

20 22 24

8

8

3

4

6 15

16

21

18 19

16

28

8

9 29 27

25

26

35

Record product's Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

2

1.17

1.16

1.15

1.14

1.13

1.12

1.11

1.10

1.9

1.8

1.7

1.6

1.5

1.4

1.3

1.2

1.1

Item 69593/69642/95553 For technical questions, please call 1-800-444-3353.

Page 15

pLEASE READ THE FOLLOWING cAREFULLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353