advertisement
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
1.
CAUTION! TO REDUCE THE
RISK OF FIRE – USE ONLY
T4 TYPE 12 WATT LAMP.
2. Do not place under direct sunlight.
Magnifying glasses can cause fires if light is directed through them at flammable surfaces. Close cover after every use.
3. Inspect before use. Do not use if parts are loose or damaged.
4. The use of any accessory attachments not recommended by the lamp manufacturer may cause injuries.
5. Do not use lamp for other than intended use.
6. Maintain labels and nameplates on the appliance. These carry important safety information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
7. Do not stare at the sun or other light source through the lamp’s magnifying lens.
8. This lamp is not a toy. Keep it out of reach of children.
9. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
10. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
11. Do not use near flammable materials.
12. Maintain products with care. Keep the lamp clean for better and safer performance. Inspect the components periodically. If damaged, have it repaired by a qualified technician
13. Do not use outdoors.
14.
IMPORTANT SAFETY
INSTRUCTIONS
This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock.
This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extensioncord unless plug can be fully inserted. Do not alter the plug.
15. Unplug from outlet when not in use and before maintenance or cleaning.
16. Risk of Electric Shock - Use In Dry Locations Only.
Page 2 For technical questions, please call 1-800-444-3353.
Item 60642
Power Cord Safety
1. A short power supply cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
2. Extension cords are available and may be used if care is exercised in their use.
3. If an extension cord is used: a. The marked electrical rating of the extension cord should be at least as great as the electrical rating of the lamp. b. The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over.
SAVE THESE INSTRUCTIONS.
Specifications
Electrical Rating 120 V~ / 60 Hz / 12W
Magnification
Bulb Type
Cord Length
Height
2X, 4.25X
T4 11W Fluorescent Lamp
57"
20"
Base Dimensions 8-1/4" L x 5-1/2" W
4006934
Item 60642 For technical questions, please call 1-800-444-3353.
Page 3
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before setup or use of this product.
Functions
Lens
Frame
Spot
Lens
Lens
Cover
Lens
Bulb Cover
(not shown)
Lower
Adjusting
Knob
Base
Upper
Adjusting
Knob
Arm
Power
Switch
(not shown)
Power Cord
(not shown)
Figure A
Page 4 For technical questions, please call 1-800-444-3353.
Item 60642
Operation
1. Plug the Power Cord into the nearest two or three prong outlet.
2. Turn on the Lamp by pushing the Power
Switch to the “I” (On) position.
3. Use the Upper and Lower Adjusting
Knobs to reach the desired angle.
Maintenance Instructions
4. To use the Lamp’s lens, lift up Lens Cover.
5. After each use, shut the Lens Cover, turn off the
Lamp by pushing the Power Switch to the “O” (Off) position and remove the Power Cord from the outlet.
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY: Unplug the Lamp, turn the Power Switch off and allow Bulb to cool completely before performing any inspection, maintenance, or cleaning procedures.
2. Keep Lamp clean and free of dirt, debris, or grease.
1. BEFORE EACH USE, inspect the general condition of the Lamp. Check for:
• loose hardware,
• cracked or broken parts,
• damaged electrical wiring or cable insulation, and
• any other condition that may affect its safe operation.
3. For longer working life, protect Lamp from sunlight and moisture.
4. AFTER USE, wipe external surfaces of the Lamp with clean cloth
Item 60642 For technical questions, please call 1-800-444-3353.
Page 5
Replacing the Bulb
1. Turn off the Lamp and unplug the Power
Cord from the outlet. Allow the lamp to cool completely. The Bulb may still be hot even after the lamp housing is cool.
2. Lay the Lamp down and set the
Adjusting Knobs so that the Lamp rests on the work area with the Bulb facing up.
3. Use a screwdriver (not included) to remove the five
Screws securing the Bulb Cover. (See Figure B.)
Screws
5. Pull the Bulb out of the Clips in the
Lens Frame. (See Figure C.)
Lens
Frame
Screws
Not
Shown
Bulb
Cover
Screws
Figure B
4. Lift the Bulb Cover away from the Lens Frame.
Note: Be careful when removing Bulb Cover; the Lens is loosely attached to the Lens Frame and could pop out.
Bulb
Clips
Figure C
6. Pull the Bulb out of the Bulb Socket. Properly dispose of the old Bulb and attach a new
Bulb to the Bulb Socket. (See Figure D.)
Bulb
Cover
Bulb
Socket
Figure D
7. Push the Bulb into the Clips and put the Bulb
Cover back into place so that the screw holes align with holes along the Lens Frame.
8. Fasten the Bulb Cover to the Lens Frame using the five Screws. Do not overtighten.
9. Once all connections are secure, return the Lamp to its normal position. .
Page 6 For technical questions, please call 1-800-444-3353.
Item 60642
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Other than the Bulb, replacement parts are not available for this item.
Item 60642 For technical questions, please call 1-800-444-3353.
Page 7
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
advertisement
Related manuals
advertisement