MAGNETIC BASE
WITH FINE ADJUSTMENT
5645
ASSEMBLY & OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright © 2000 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
REV 05h, 09i
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below:
Model___________ Serial No._____________ Purchase Date_____________
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual.
Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Product Name:
Item Number:
Magnetic Pull:
Technical Specifications
Magnetic Base
5645
45 Lbs.
IMPORTANT SAFETY INSTRUCTIONS!
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT!
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1.
Keep work area clean. Cluttered areas invite injuries.
2. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords.
3. Store idle equipment. When not in use, products must be stored in a dry location. Always lock up the
Airplane and keep out of reach of children.
4. Do not force product. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity.
5. Use the right product for the job. Do not attempt to force a small product or attachment to do the work of a larger industrial product. There are certain applications for which this product was designed. Do not modify this product and do not use this product for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Wear restrictive hair covering to contain long hair.
7. Check for damaged parts. Before using, any part that appears damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician.
8. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of
any other parts will void the warranty. Approved accessories are available from Harbor Freight Tools.
#5645 Page 2
9. Do not use this product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product.
10. Use eye protection. Always wear ANSI approved impact safety goggles.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Assembly
Your Magnetic Base will require some assembly as described in the following steps. To assist you with assembly and operation please refer to the Parts List located on the last page of this manual.
Step 1) Thread the Upright Post with Lock Nut (#2) onto the Base (#1).
Step 2) The Upright Post Swivel (#3) should be slid into place on the Upright Post with Lock Nut
(#2). Turn the Upright Post Swivel clockwise to secure it in place. Insert the Snug Gauge
Rod (#4) through the Upright Post Swivel (#3).
Step 3) Slide the Indicator Clamp (#5) onto the Snug Gauge Rod (#4).
Operation
Settings and Adjustments
When making adjustments, make certain that all thumbscrews are fully tightened and Swivels are secure when adjustments are complete.
The Magnetic Base can be attached to flat or round surfaces. For use on a Q.A. table, it can reach out 12”. It can be set to many different positions.
Step 1) Set the Base (#1) in the desired position. Turn the Dial counterclockwise to “ON” to engage the Magnet.
Step 2)
Step 3)
Step 4)
Loosen the thumbscrew on the Upright Post Swivel (#3) and move the Upright Post Swivel
(#3) and the Snug Gauge Rod (#4) to the desired location.
Position the Indicator Clamp (#5) as desired.
Turn the Fine Adjustment (#6) knob to fine tune the position of the Snug Gauge Rod (#4).
#5645 Page 3
Unpacking
When unpacking your Magnetic Base, check to make sure the following parts are included. If any parts are missing or borken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Part # Description Quantity
1.
2.
3.
4.
5.
6.
Base
Indicator Clamp
Fine Adjustment
Upright Post with Lock Nut
Upright Post Swivel
Snug Gauge Rod
7. 5/16” Adjustment Bushing 1
1
1
1
1
1
1
Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
Upright Post Swivel (#3)
Fine Adjustment (#6)
Snug Gauge Rod (#4)
Upright Post with Lock Nut (#2) Indicator Clamp (#5)
Hex Stud
Dial in “OFF” position
Base (#1)
# 7
Note: Part# 7 (5/16” Adjustment Bushing) fits into part# 5. It will allows you to clamp 5/16” stem dial indicators. Without the bushing it will clamp 3/8” stem dial indicators. The bushing is held in place with a small hex stud.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
#5645
REV 06d
Page 4
