Hotpoint E302X Electric Hob User manual

Instructions for Installation and Use

Electric Hob

Model E302X

Introduction

For Your Safety

Know your Hob

How to use your Hob

Practical Advice

Care and Cleaning

Troubleshooting

Installation

Electrical Connection

After Sales Service

Hotpoint Guarantee

Key Contacts

CONTENTS

9

10

11

Back Cover

7

7

5

6

8

3

4

5

Retention of this Instruction Book

This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance.

If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings.

If the Book is lost or damaged a copy may be obtained from:

GDA LTD., Morley Way, Peterborough, PE2 9JB

2

Introduction

Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions detailed in this booklet.

To help make best use of your cooking equipment, please read this booklet carefully.

The hob is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.

When first using the hob ensure that the room is well ventilated (eg. open a window or use an extractor fan) and that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the room until the odour has ceased. This odour is due to temporary finish on elements.

* The guarantee is subject to the provisions that the appliance:

(a) Has been used solely in accordance with this booklet.

(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the appliance.

(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the manufacturers authorised employee or agent.

(d) Has been correctly installed.

This appliance conforms with the following European Economic Community directives

73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications.

89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications.

93/68/EEC of 22/07/93 and subsequent modifications.

3

For Your Safety

When used properly your appliance is completely safe but as with any electrical product there are certain precautions that must be observed.

PLEASE READ THE BELOW PRECAUTIONS BEFORE USING YOUR APPLIANCE.

To maintain the efficiency and safety of this appliance, we recommend you do the following:

- only call the Service Centres authorised by the manufacturer.

- always use genuine spare parts.

ALWAYS:

- make sure you remove all packaging and dispose of safely.

- check the soundness of the appliance after it has been unpacked.

- make sure you understand the controls before using the appliance.

- keep children away from the appliance during use.

- take care to avoid heat/steam burns when operating the controls.

- make sure the controls are turned off when you have finished cooking and when not in use.

- disconnect from the power supply, and allow to cool, before cleaning or performing maintenance.

- refer servicing to a qualified appliance service engineer.

- keep the hob clean as a build up of grease or fat from cooking can cause a fire.

- follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.

- dry food thoroughly before frying and lower it slowly into the hot oil or fat. Frozen food in particular, will cause froth and spitting if added too quickly.

- keep outside of pans clean and free from streaks of oil or fat.

- place pans centrally over the hotplates making sure handles are kept away from the edge of the hob and cannot be heated by other hotplates/pans.

- keep any ventilation slots clear of obstructions.

NEVER:

- attempt to install or repair the appliance without the assistance of qualified personnel.

- store items above the appliance that children may attempt to reach.

- heat up unopened food containers, as pressure can build up causing the container to burst.

- use the appliance to heat up anything other than food.

- use the appliance as a room heater.

- dry any items on the hob.

- install the appliance next to curtains or other soft furnishings.

- allow children to play with or tamper with the controls.

- leave children unsupervised where cooking appliances are installed as all the cooking surfaces get hot during and after use.

- store chemicals, foodstuffs or pressurised containers in or on the appliance, or in cabinets immediately above or next to the appliance.

- use flammable or plastic items on or near the hob.

- use adapters, multiple sockets and/or extension leads.

- fill a deep fat frying pan more than 1/3 full of oil, or use a lid.

DO NOT LEAVE UNATTENDED WHILE COOKING.

- fry too much food at a time, especially frozen food. This only lowers the temperature or the oil or fat too much, resulting in greasy food.

- pull on the appliance or the supply cable to unplug it from the electrical outlet.

- allow power cables of other appliances to come into contact with hot parts of this appliance.

- expose the appliance to atmospheric agents, such as rain or sunlight.

- operate the appliance with wet hands.

- operate the appliance when barefoot.

- allow anyone to sit or stand on any part of the appliance.

- use misshapen pans which may be unstable.

- use fish kettles or large preserving pans across two hotplates.

- leave anything on the hob surface when unattended and not in use.

SAFETY ADVICE

IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly for deep fat frying. Cooking utensils containing oil must not be left unattended (eg. to answer the telephone) on or in close proximity to the cooking areas.

IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:

1. Turn off the hotplates.

2. Cover the pan with a fire blanket or damp cloth, this will smother the flames and extinguish the fire.

3. Leave the pan to cool for at least 60 minutes before moving it. Injuries are often caused by picking up a hot pan and rushing outside with it.

NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan over. Never use water to extinguish oil or fat fires.

4

Know your Hob

C

A

A

1 and 2 Cooking areas

1A and 2B Controls

A B

5

6

3

4

1

2

Quick /

Normal

Automatic

1 - 2

3 - 4

5 - 6

7 - 8

9 - 10

11 - 12

How To Use Your Hob

Heat

Least Hot

To turn on a cooking area and increase its power

level, select the desired cooking area. Then turn the corresponding control to the required position. The higher the number, the greater the power.

Controls for "Quick/Normal" plates turn in both directions to settings numbered 0 - 6.

Only turn controls for "Automatic" plates clockwise to settings numberes 0 - 12.

Hottest

To turn off the cooking area, return the control to 0 and the cooking area is turned off.

Pilot light

The pilot light will come on when cooking areas are switched on.

Even after a cooking area is turned off some types of pilot light stay on to show that the cooking area is still hot. The pilot light warns you there is still the risk of injury by burning.

5

Practical Advice

Choice of utensils:

Every Electric Hob deserves the right choice of utensils. We recommend for optimum performance the use of good quality utensils.

PANS SHOULD NOT:

• Be concave (bowed in).

• Be convex (bowed out).

• Be rimmed.

• Be deeply ridged.

BUT SHOULD BE ESSENTIALLY FLAT

Always

• Use good quality flat-based cookware on all electric heat sources.

• Place pans centrally on the hotplate.

• Ensure pans have clean, dry bases before use.

• Ensure pans match the size of the heating area.

• Remember good quality pans retain heat well, so generally only a low or medium heat is necessary.

• Ensure pan handles are positioned safely and away from heat sources.

• Lift pans, do not drag.

• Use pan lids, except when frying.

• Deal with spillage immediately, but with care.

Never

• Use gauze, metal pan diffusers, asbestos mats and stands eg. wok stands - they can cause overheating.

• Use utensils with skirts or rims eg. buckets and some kettles.

• Use badly dented or distorted pans.

• Leave an element on when not cooking.

• Cook food directly on the hotplate.

• Drag or slide utensils across the hotplate.

• Place large preserving pans or fish kettles across two hotplates.

• Place plastic vessels or utensils on a hot hob.

• Use the hob as an area for storage.

6

Care and Cleaning

Before cleaning or performing maintenance on your hob, disconnect it from the power supply. Check that all controls are in the OFF position before reconnecting.

Clean spills immediately.

NEVER USE: Washing powder, harch abrasive, scouring pads, aerosol cleaners or oven chemical clearners of any kind.

Cleaning materials to avoid

• Household abrasive powders, eg. Vim.

• Oven chemical cleaners, aerosols and oven pads -

Caustic cleaners such as these will etch the surface and attack the metal frame.

• Bath and sink cleaners may mark the surface.

The Hotplates

Clean with a cloth wrung out in warm water. Then rub a litlle cooking oil into the hotplates while they are still warm to condition the surface. Ensure care is taken as the hotplates will be warm.

Enamelled, Stainless Steel and Glass parts

Wipe with a cloth wrung out in warm soapy water followed by a wipe with a cloth wrung out in clean water and then dry with a soft clean cloth.

Control Knobs

Wipe over the knobs with a soft cloth wrung out in warm soapy water or mild non-abrasive. Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth.

Painted Metal Surround Trim

Wipe over with a cloth wrung out in warm soapy water only. DO NOT USE ABRASIVES.

Troubleshooting

Before calling service for assistance, check through the following list, there may be nothing wrong.

Nothing works.

Check to make sure that:

• the mains wall switch is switched on.

If a control is on, the corresponding pilot light will come on.

Hotplates are slow to boil or will not simmer.

Check to make sure that:

• Your pans conform with the recommendations detailed in this book.

If, despite all of these checks, the hob does not function properly and problem persists, call Hotpoint Service (see

KEY CONTACTS, back page), informing them of:

- The type of problem.

- The abbreviation used to identify the model (Mod. ...) as indicated on the warranty.

IMPORTANT:

Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original.

7

Installation

These instructions are intended for the qualified technician installing the appliance in order to insure that the installation, adjustments and maintenance procedures are performed correctly and comply with the regulations currently in effect.

Important: the hob must be disconnected from the power supply before making any adjustments or performing any maintenance, etc.

Installing built-in hobs

The hob is a type Y appliance, therefore, the hob can be installed alongside of cabinets which are higher than the surface of the worktop. The following precautionary measures should be observed in order to ensure proper installation:

a) Hoods must be installed in compliance with the required specifications contained in the instruction manual for the hood itself.

b) The dimensions and the position of the hole are shown below:

These measurements must absolutely be observed in so far as improper installation can cause the surrounding surface areas to overheat. It is recommended that the hob be installed at a distance of at least 55 mm from the back wall or other vertical surfaces to ensure that the air circulates properly over the cooking area and to avoid overheating the surrounding surfaces. A seal or gasket is provided with the hob, make sure that it adheres properly to the bottom part of the frame of the hob.

The seal must fit properly around the entire hob frame and especially along the corners in order to create a seal between the work top and the hob itself so as to prevent spills or splashes from leaking into the cabinet below.

The hob must be fixed into the worktop using the fixing clamps

- see diagram.

Very important

It is essential to install the hob on a totally flat surface. Any damage caused by incorrect fitting may alter the characteristics or impair performance.

Insert the hob into the hole, pressing firmly around the frame to make it adhere to the counter top.

Note: If the hob is installed above a built-in oven, it is preferable that the oven be installed in such a way that it is set on two strips of wood; if the oven is installed on a continuous base, there must be an opening in the back of at least 45 x 560 mm.

The built-in oven must be equipped with a forced air cooling system.

8

Electrical Connection

Electrical Connection

THIS APPLIANCE MUST BE EARTHED.

The installation procedure must be carried out by a qualified electrician.

The electrical safety of this appliance is guaranteed only if the appliance is correctly earthed in compliance with the standards of electrical safety.

The manufacturer can under no circumstances be considered responsible for any damage that might occur due to incorrect earthing of the hob.

Connecting the supply cord to the electrical mains:

The hob must be connected to a double pole mains switch which must be installed between the appliance and the mains. The double pole mains switch must have a minimum of 3mm of space between the contacts, be sized to the load and comply with current regulations (the switch must not be able to disconnect the earth conductor).

The supply cord should conform to BS6004 conductor size

4mm

2

and must be positioned so that no part of it reaches a temperature of 50°C higher than room temperature.

Before making the connection, make sure that:

• the limiter switch (fuse) and the residual wiring can support the appliance load (see the rating plate, below).

• the mains system is properly earthed in compliance with current regulations and provisions.

• there is easy access to the socket or the double pole mains switch after the appliance is installed.

• the isolation switch must not be positioned directly above the hob.

IMPORTANT:

If the hob is installed above a built-in oven, the electrical connection for the hob must be independent of that for the oven, both for safety reasons and to facilitate the removal of the oven for maintenance, repair etc.

HOTPLATES:

Normal Hotplate O145 1000W

Normal Hotplate O180 1500W

Quick Hoplate O145 1500W

Quick Hotplate O180 2000W

Automatic Hotplate O145 1500W

Automatic Hotplate O180 2000W

Red Spot

Red Spot

9

After Sales Service

"No company is better positioned to offer an after sales service on a

Hotpoint appliance than us - the manufacturer"

As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of free

replacement parts for the first 5 years when fitted by a Hotpoint engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service options:

Repair Service and Information Help Desk

UK: 08709 066066 www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the Model number and the Serial number of your appliance

Available 364 days a year with a fast, effective and value for money service. We have the largest white goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour guarantee for 12 months from the date of the repair.

If you require any information or have any questions about your appliance, our operators are on hand with help and advice.

All this ensures that you will receive the best available after sales service possible.

Extended Warranties

UK: 08709 088 088 www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover

Repair Protection Plan plans to give you total peace of mind.

FREE service repairs for a single Hotpoint appliance during the period

Kitchen Cover of cover.

FREE service repairs for all your Hotpoint appliances less than 8 years old.

Genuine Parts and AccessoriesUK: 08709 077 077 www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

A wide range of genuine parts and accessories are available from our hotline or through our web site.

Genuine parts and accessories, extended warranties and service repairs are all available on our web-site at:

GB

www.theservicecentre.co.uk

10

Guarantee

"Satisfaction guaranteed or your money back"

We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for an engineer to call. If the technical problem is not resolved under this guarantee, we will replace your machine or, if you prefer, give you your money back.

All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.

Guarantee terms and conditions

Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the following provisions that your appliance:

Has been installed and used correctly in accordance with this instruction booklet.

Has been used solely for domestic purposes and is located on domestic premises (ie. not for commercial or trade use).

Has been properly connected to a suitable electrical supply voltage as stated on the appliance rating plate.

Has not been subject to misuse, accident, modified or repaired by anyone other than one of our own service engineers.

For pre purchase information on any other Hotpoint product call: 08701 50 60 70 or visit: www.hotpoint.co.uk

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully.

To minimise risk of injury to children, remove the plug and cut mains cable off flush with the appliance.

Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket.

GB

11

Key Contacts

After Sales Service

Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and services we offer.

Repair Service and Information Desk

UK: 08709 066 066

(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays) www.theservicecentre.co.uk

Republic of Ireland: 1850 302 200

Note: Our operators will require the following information:

Model number:

Serial number:

Extended Warranties

UK: 08709 088 088

(Open 8 to 8 Mon - Sun) www.theservicecentre.co.uk

Republic of Ireland: 1850 502 200

Genuine Parts and Accessories

UK: 08709 077 077

(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat) www.theservicecentre.co.uk

Republic of Ireland: (01) 842 6836

COD. 1.002.63.0

General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB.

February 2003 Part no. FP165 - 01