Imagine Communications SEL UCIP1 Uncompressed Video-Over-IP Module Installation and Operation Manual

PDF

Documento

Anuncio

Installation and Operation Manual

Selenio SEL-UCIP1

Uncompressed Video-Over-IP Module

Version 2.0

April 2016

Selenio SEL-UCIP1 Uncompressed Video-Over-IP Module Installation and Operation Manual

Publication Information

Proprietary and Confidential.

Imagine Communications considers this document and its contents to be proprietary and confidential.

Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine Communications. All others uses are illegal.

This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product.

Trademarks

Selenio™ is a trademark of Imagine Communications or its subsidiaries. Microsoft® and Windows® are registered trademarks of Microsoft Corporation. HD-BNC is a trademark of Amphenol Corporation.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. All other trademarks and trade names are the property of their respective companies.

Contact Information

Imagine Communications has office locations around the world. For domestic and international location and contact information, visit our Contact page (http://www.imaginecommunications.com/howbuy/contact-us).

Support Contact Information

For domestic and international support contact information see:

• Support Contacts (http://www.imaginecommunications.com/how-buy/contact-us)

• Worldwide Support e-mail (mailto: [email protected])

• Customer Community Portal (http://app.imaginecommunications.com/customercommunity)

• Warranty & Contract Information (http://www.imaginecommunications.com/services/customercare)

• MyImagine Academy Training (http://www.imaginecommunications-academy.com)

• Product Manuals (http://www.imaginecommunications.com/services/product-manuals)

Selenio SEL-UCIP1

Installation and Operation Manual Contents

Preface ................................................................................................................... 5

Manual Information ................................................................................................................................. 5

Purpose ................................................................................................................................................. 5

Audience ............................................................................................................................................... 5

Revision History .................................................................................................................................... 5

Writing Conventions ............................................................................................................................. 5

Obtaining Documents ........................................................................................................................... 6

Unpacking/Shipping Information ............................................................................................................. 6

Safety Standards and Compliances .......................................................................................................... 7

Restrictions on Hazardous Substances (RoHS) ..................................................................................... 7

Waste from Electrical and Electronic Equipment (WEEE) .................................................................... 7

Introduction ........................................................................................................... 9

Available Configurations ........................................................................................................................... 9

SFP+ Modules ......................................................................................................................................... 10

Main Features ......................................................................................................................................... 11

Classic Mode or Module ..................................................................................................................... 12

AES67 Mode or Module ..................................................................................................................... 12

Front Module .......................................................................................................................................... 13

LEDs .................................................................................................................................................... 14

Back Module ........................................................................................................................................... 16

Connecting to a PTP Source ............................................................................................................... 17

Signal Flow .............................................................................................................................................. 19

Installation ........................................................................................................... 21

Powering Up a Module ........................................................................................................................... 21

Upgrading Module Firmware ................................................................................................................. 21

Upgrade Failure Instructions .............................................................................................................. 22

Accessing MIBs ....................................................................................................................................... 22

Setting Up Your SEL-UCIP1 ................................................................................... 24

Classic Mode ........................................................................................................................................... 24

AES67 Mode ........................................................................................................................................... 24

Selenio SEL-UCIP1

Installation and Operation Manual Contents

Deterministic Video/Audio Switching .................................................................................................... 25

Parameters ............................................................................................................................................. 25

Module Configuration/AES67 Configuration ..................................................................................... 25

SDI Video Interface Configuration and Status .................................................................................... 30

SDI to IP .............................................................................................................................................. 31

IP to SDI .............................................................................................................................................. 37

WAN Configuration and Status .......................................................................................................... 48

Alarms ..................................................................................................................................................... 50

Laser Safety for Fiber Optic Back Modules ........................................................... 52

Precautions for Enclosed Systems .......................................................................................................... 52

Precautions for Unenclosed Systems ..................................................................................................... 53

Label ....................................................................................................................................................... 53

Inspecting and Cleaning Fiber Optic Connections .................................................................................. 53

Important Points ................................................................................................................................ 54

Inspection Procedure ......................................................................................................................... 55

Dry Cleaning Procedure ...................................................................................................................... 55

Wet Cleaning Procedure .................................................................................................................... 56

Specifications ....................................................................................................... 57

HD/SD-SDI Input Specifications .............................................................................................................. 57

HD/SD-SDI Output Specifications ........................................................................................................... 58

SFP+ Specifications ................................................................................................................................. 59

OP+SFP+TRSM+10G Single Mode Optical Transceiver ....................................................................... 59

OP+SFP+TRMM+10G Multi Mode Optical Transceiver ...................................................................... 60

SEL+AOC+10G ..................................................................................................................................... 61

Power Consumption ............................................................................................................................... 61

Propagation Delay .................................................................................................................................. 61

Index .................................................................................................................... 62

Selenio SEL-UCIP1

Installation and Operation Manual

Preface

Manual Information

Purpose

This manual provides information about the SEL-UCIP1 module.

Audience

This manual is written for engineers, technicians, and operators responsible for installation, setup, maintenance, and operation of the SEL-UCIP1 module.

Revision History

Edition

1.0

1.1

Date

February 2015

May 2015

2.0 April 2016

Revision History

Initial Release

Addition of SFP information

Addition of AES67 option and features

Writing Conventions

This manual adheres to the following writing conventions.

Table 1: Writing Conventions

Term or

Convention

Bold

Description

Indicates dialog box, property sheet, field, button, check box, list box, combo box, menu, submenu, window, list, and selection names

Italics

CAPS

Indicates email addresses, names of books and publications, and first instances of new terms and specialized words that need emphasis

Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL, ALT, DELETE

Code

Indicates variables or command-line entries, such as a DOS entry or something you type into a field.

Indicates the direction of navigation through a hierarchy of menus and windows. hyperlink Indicates a jump to another location within the electronic document or elsewhere

Selenio SEL-UCIP1

Installation and Operation Manual

Term or

Convention

Internet address

Description

Indicates a jump to a Web site or URL

Note

Indicates important information that helps to avoid and troubleshoot problems

Preface

Obtaining Documents

Product support documents can be viewed or downloaded from our website. Alternatively, contact your

Customer Service representative to request a document.

Unpacking/Shipping Information

This product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service.

1. Check equipment for any visible damage that may have occurred during transit.

2. Confirm that you have received all items listed on the packing list.

3. Contact your dealer if any item on the packing list is missing.

4. Contact the carrier if any item is damaged.

5. Remove all packaging material from the product and its associated components before you install the unit.

Keep at least one set of original packaging, in the event that you need to return a product for servicing.

In the unlikely event that your product fails to operate properly, please contact Customer Service to obtain a Return Authorization (RA) number, then send the unit back for servicing.

Keep at least one set of original packaging in the event that a product needs to be returned for service.

If the original package is not available, you can supply your own packaging as long as it meets the following criteria:

• The packaging must be able to withstand the product’s weight.

• The product must be held rigid within the packaging.

• There must be at least 2 in. (5 cm) of space between the product and the container.

• The corners of the product must be protected.

Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing.

Selenio SEL-UCIP1

Installation and Operation Manual

Safety Standards and Compliances

See the fiber optic section for information about the safe use of fiber optic products. Also see the

Selenio MCP Series safety manual, available on our website.

Preface

Restrictions on Hazardous Substances (RoHS)

Directive 2011/65/EU (ROHS2)—commonly known as the European Union (EU) Restriction on Hazardous

Substances (RoHS)—sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive took effect on July 1, 2006, and it refers to the following hazardous substances:

• Lead (Pb)

• Mercury (Hg)

• Cadmium (Cd)

• Hexavalent Chromium (Cr-V1)

• Polybrominated Biphenyls (PBB)

• Polybrominated Diphenyl Ethers (PBDE)

According to this EU Directive, all products sold in the European Union are fully RoHS-compliant and

"lead-free." (See our website for more information.) Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Equipment that complies with the

EU directive are marked with a RoHS-compliant emblem, as shown.

Figure 1: ROHS Compliance Symbol

Waste from Electrical and Electronic Equipment (WEEE)

The European Union (EU) Directive 2002/96/EC on Waste from Electrical and Electronic Equipment

(WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. Effective August 13,

2005, producers or users are required to recycle electrical and electronic equipment at end of its useful life, and may not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.)

Selenio SEL-UCIP1

Installation and Operation Manual Preface

In accordance with this EU Directive, companies selling electric or electronic devices in the EU will affix labels indicating that such products must be properly recycled. (See our website for more information.)

Contact your local sales representative for information on returning these products for recycling.

Equipment that complies with the EU directive is marked with a WEEE-compliant emblem, as shown.

Figure 2: WEEE Symbol

Selenio SEL-UCIP1

Installation and Operation Manual

Introduction

The Selenio™ SEL-UCIP1 is a multichannel SDI-to-IP encapsulator and IP-to-SDI de-encapsulator. It is sold in two versions: Classic and AES67. The classic SEL-UCIP1 has eight HD/SD-SDI interfaces, configurable to a maximum of six inputs and/or four outputs, not totaling more than eight I/Os. The AES67 version has four inputs and four outputs.

Both the classic and AES67 versions of the SEL-UCIP1 support SMPTE 2022-6 encapsulation and deencapsulation and SMPTE 2022-7 seamless switching for link redundancy.

The base module, or when operating in Classic mode, supports SMPTE 2022-5 Forward Error Correction

(FEC).

The AES67 version is available as a complete module, or as a software upgrade. This mode or version supports Audio over IP in the form of 16 mono AES67 signals or 8 stereo AES67 signals per video channel, with reference to SMPTE 2059 / IEEE 1588 Precision Time Protocol.

Note: SMPTE 2022-5 FEC is not available when in AES67 mode.

Each of the two SFP+ IP network ports can support 10Gbit Ethernet (10GbE), and are compatible with the qualified SFP+ transceivers shown in the table below.

SEL-UCIP1 modules are designed for Selenio MCP1 and MCP3 frames.

Available Configurations

Table 2: Available SEL-UCIP1 Configurations

Part Number Description

Modules

SEL-4UCIP1-EOS

Uncompressed-over-IP encapsulation/de-encapsulation; includes four independent unidirectional HD/SD-SDI channels that can be assigned as either "transmitter" or

"receiver" over 10 GbE IP. Includes front module and single back module with eight

HD-BNC connectors for SDI signals, and dual SFP+ cages, supporting 10 GbE links, with MSDNO stream licenses (SFP+ options must be ordered separately).

The following back module configurations are possible:

• 0 SDI In and 4 SDI Out

• 2 SDI In and 2 SDI Out

• 4 SDI In and 0 SDI Out

• CTR + 1 SDI In, 2 SDI Out

• CTR + 3 SDI In, 0 SDI Out

Selenio SEL-UCIP1

Installation and Operation Manual

Part Number Description

SEL-8UCIP1-EOS

SEL-8UCIP1-A67-EOS

Introduction

Uncompressed-over-IP encapsulation/de-encapsulation; includes eight unidirectional HD/SD-SDI channels* that can be assigned as either "transmitter" or

"receiver" over 10 GbE IP. Includes front module and single back module with eight

HD-BNC connectors for SDI signals, and dual SFP+ cages, supporting 10 GbE links, with MSDNO stream licenses (SFP+ options must be ordered separately).

The following back module configurations are possible:

• 4 SDI In and 4 SDI Out

• 6 SDI In and 2 SDI Out

• CTR + 3 SDI In, 4 SDI Out

• CTR + 5 SDI In, 2 SDI Out

Uncompressed-over-IP encapsulation/de-encapsulation; includes eight unidirectional 3G/HD/SD-SDI channels assigned as four transmitters and four receivers over 10GbE IP, with support for 16 mono AES67 signals or 8 stereo AES67 signals per video channel. Includes front module and a single back module with eight HD-BNC connectors for SDI signals, and dual SFP+ cages, supporting 10GbE links, with MSDNO stream licenses (SFP+ options must be ordered separately).

This option provides a back module configuration of 4 SDI In and 4 SDI Out.

Softkeys

SELOPT-SK-8UCIP

SELOPT-SK-8UC-A67

Software key option for uncompressed over IP module expansion to eight unidirectional HD/SD-SDI channels* that can be assigned as either "transmitter" or

"receiver" over 10 GbE IP.

Software key option for uncompressed-over-IP module; requires eight unidirectional channels (as SEL-8UCIP1-EOS). Adds support for 3G video and up to

16 mono or 8 stereo AES67 audio-over-IP signals per video channel.

*Depending on the module configuration, the SEL-UCIP1 can have a maximum of six inputs and/or four outputs, totaling no more than eight I/Os.

SFP+ Modules

Table 3: Available SFP+ Modules

Part Number

SEL+AOC+10G

Description

10GbE SFP+ active optical Direct Attach Cable, with hot-pluggable SFP+ cable ends, 10 meter length, low power

OP+SFP+TRMM+10G

10GBASE-SR fiber-enhanced small form factor pluggable SFP+ transceiver, capable of 10 GbE links, up to a maximum link length of 984 ft (300 m) on

2000 MHz-km multi-mode fiber

OP+SFP+TRSM+10G

10GBASE-LR fiber-enhanced small form factor pluggable SFP+ transceiver, capable of 10 GbE links, up to a maximum length of 6.2 miles (10 km) over single mode fiber.

Selenio SEL-UCIP1

Installation and Operation Manual Introduction

Note: If the extractor handle on an SFP+ module breaks or fails, the retention latch can be gently pulled away from the SFP+ module using a small flat head screwdriver. See below.

Figure 3: Removal of SFP with Broken Latch

Main Features

• Supports bi-directional multi-channel transport of HD/SD-SDI video signals over 10 GbE link on a single slot module

• Supports SMPTE 2022-6 RTP transport over 10GbE IP links

• Supports SMPTE 2022-7 seamless protection specification

• Provides eight HD/SD-SDI interfaces, configurable to a maximum of six inputs/four outputs using

HD-BNCs connectors (requires SELOPT-SK-8UCIP option for eight connectors; the SEL-UCIP1 can have a maximum of six inputs and/or four outputs, totaling no more than eight I/Os)

• Transmits up to six streams of SDI-to-IP simultaneously, and receives up to four streams of IP-to-SDI simultaneously (within the limits of available I/O connectors and bandwidth on the Ethernet link)

• Provides two Tx/Rx configurations (8-channel version):



Up to four HD/SD independent transmit channels + four HD/SD independent receive channels simultaneously



Up to six HD/SD independent transmit channels + two HD/SD independent receive channels simultaneously

Selenio SEL-UCIP1

Installation and Operation Manual Introduction

• Provides frame syncing of all SDI output signals (Receive side), including audio sample rate conversion to the frame reference

• Transparently passes non-PCM audio (Dolby -E

)

• Supports thumbnail monitoring of a video input or output port (some exceptions apply)

• Clean switches between input video on IP sources, and passes-through all SDI audio and HANC and

VANC data

• Supports additional SDI input/output via the Selenio frame's internal video cross point

• Provides dual-network interfaces, supporting 10 Gb/sec Ethernet over SFP+ fiber

• Provides auto detection, status, and monitoring of the SDI input standard

• Supports unicast and multicast transmission

• Supports up to six VLANs in total on module external interfaces

• Synchronizes up to eight stereo pairs of input audio per video stream

• Maintains sync on PCM signals using sample-rate conversion

• Supports RP168-2009 standard switching between two SDI sources for seamless change of downstream devices

• Supports Selenio MCP standard module redundancy

• Upgradeable for different channel options using software-keys

• Provides VANC data drop/repeat with video sync events

• Supports Selenio MCP standard software upgrade method

• Supports SDI Loopback of any SDI input, to any and all SDI outputs in the same module; includes video and audio frame synchronization of the looped-back SDI input

Classic Mode or Module

Supports SMPTE 2022-5 Forward Error Correction for protection against packet losses created by occasional network errors.

When using audio in classic mode or on a classic module, the SEL-UCIP1 uses RTP (Real-Time Protocol) to manage packet load order, timing, and synchronization.

AES67 Mode or Module

Supports AES67 audio.

When using AES67 audio, the SEL-UCIP1 uses PTP (Precision Time Protocol) to manage packet load order, timing, and synchronization.

Selenio SEL-UCIP1

Installation and Operation Manual

Front Module

Introduction

Figure 4: SEL-UCIP1 Front Module

Selenio SEL-UCIP1

Installation and Operation Manual

LEDs

Introduction

Figure 5: Card-Edge LEDs

Table 4: LED Descriptions

LED Number LED Function

D33

D22 to D30

D34

Power

Status_BNC_1 to 8

Color

Red

Red and

Green

Definition

Power is on

Module is initializing

Off

Green

Off

Sec. CTRL Eth. Link Off

Module is operating normally, and communicating with resource module in frame

Power is off

• An SDI signal has been detected at that BNC connector (when configured as input)

• The SDI signal is being driven out of that BNC connector (when configured as an output)

SDI signal not present or no output

No communication to the secondary Selenio MCP controller module

The communications link to the secondary Selenio MCP controller module is working.

Selenio SEL-UCIP1

Installation and Operation Manual

LED Number LED Function

D35

Sec. CTRL Eth. Act

Pri. CTRL Eth. Act

Color

Off

Introduction

Definition

No communications activity on the Ethernet interface to/from the secondary resource module

Blinking There is communications activity on the Ethernet interface to/from the secondary resource module

Pri.. CTRL Eth. Link Off No communication to the primary Selenio MCP controller module

On The communications link to the primary Selenio MCP controller module is working.

No communications activity on the Ethernet interface to/from the primary resource module

D44

Blinking There is communications activity on the Ethernet interface to/from the primary resource module

FPGA Config. Done Off FPGA is being load with configuration data

On FPGA configuration has loaded correctly

Selenio SEL-UCIP1

Installation and Operation Manual

Back Module

Introduction

Figure 6: Selenio SEL-UCIP1 Back Module Swatch and Connector Assignments

Selenio SEL-UCIP1

Installation and Operation Manual

Connecting to a PTP Source

Introduction

When connecting SEL-UCIP1 for AES67 use, you will need to connect to a Precision Time Protocol (PTP)

IEEE-1588 source.

The 1588 standard assumes symmetrical path delay. It you have different rate paths (E.g. VSG-4MTG at

100Mbps and UCIP at 10G), the One Way Delay (OWD) calculation is incorrect. Two parameters controls allow SEL-UCIP1 to compensate for this error: Network from Master/Boundary Clock and OWD Offset,

listed in Control (on page 28).

To configure these parameters, follow these steps:

1. From Module Configuration > PTP 1588 > Control, select the Network from Master/Boundary

Clock option that best describes your network configuration.

This parameter makes an OWD calculation based on an assumption of how the switch behaves internally. Not all switches will always behave this way.

2. Using a PTP master with a 2059-1 aligned black output, measure the relative timing of the UCIP-

AES67 SDI output to the PTP master’s black output. E.g. WFM8300.

3. Enter this value in the OWD Offset control, which is also found under Module Configuration > PTP

1588 > Control.

Selenio SEL-UCIP1

Installation and Operation Manual

Cables

Manufacture Name Manufacture model # Description

Finisar

Avago

FCBG110SD1C10

AFBR-2CAR10Z

Active Optical SFP+ Direct Attach

Cable, 10 meter, 850 nm

Active Optical SFP+ Direct Attach

Cable, 10 meter, 850 nm

6A11-A0121-010.0-0 Active Optical SFP+ Direct Attach

Cable, 10 meter, 850 nm

Amphenol

Belden

Brocade

SF-SFPP2EPASS-007 Passive Copper SFP+ Direct Attach

Cable, 7 meter

SSFPP-P0023F Passive Copper SFP+ Direct Attach

Cable, 7 meter

10G-SFPP-TWX-0308 Active Copper SFP+ Direct Attach

Cable, 3 meter

Introduction

Notes:

recommended recommended not recommended not recommended not recommended acceptable

Application Diagram

AES67 audio is not embedded with the video, so it could be sent for example to an audio mixer and then realigned with the video. The real advantage is that the reference alignment and AV timing is done using

PTP so it's going to be much more reliable. For compatibility purposes, when you are using AES67 audio, the SEL-UCIP1 accepts 1-8 channels, but will only process and route channels 1 and 2.

Note: The preferred vendor for switches when working with SEL-UCIP1 is Arista.

Selenio SEL-UCIP1

Installation and Operation Manual

Signal Flow

Introduction

Figure 7: Four-Channel SEL-UCIP1 Module Signal Flow

Figure 8: Eight-Channel SEL-UCIP1 Module Signal Flow

Selenio SEL-UCIP1

Installation and Operation Manual Introduction

Figure 9: Eight-Channel AES67 SEL-UCIP1 Signal Flow

Selenio SEL-UCIP1

Installation and Operation Manual

Installation

The SEL-UCIP1 can be installed in SEL-MCP1 and SEL-MCP3 frames. Due to space limitations, the SEL-

UCIP1 cannot be installed in the center position of a version 1 MCP1 frame. There is no slot restriction on installing the module in a version 2 MCP1 frame. You can tell what type of SEL-MCP1 frame you have by looking at the center back of the frame. Version 2 frames are identified with a "V2" label.

See your frame's manual for complete instructions on installing and removing modules.

Note: When installing the SEL-UCIP1 module in a SEL-MCP3 frame, check to ensure that the boardmounted fan module is flush with the heat sink. If the fan is protruding, it may scrape and damage the adjacent MCP module in the frame.

Figure 10: Position of Module Fan

Powering Up a Module

SEL-UCIP1 modules are ready for use when their parameters appear in the Selenio user interface.

Selenio modules are automatically powered up when they are inserted into a live (powered up) frame, and whenever the frame is powered up.

The maximum power consumption of a SEL-UCIP1 module is 40 W.

Upgrading Module Firmware

All module firmware upgrades are activated in the frame controller section of the Selenio MCP3 user interface. Follow this path to find the appropriate parameters: Configuration > Frame Controller >

Configuration tab > Upgrade Firmware. See the Selenio MCP3 frame manual for information on how to upgrade module firmware. In the unlikely event of an upgrade failure, see Upgrade Failure Instructions

(on page 22).

Selenio SEL-UCIP1

Installation and Operation Manual

Upgrade Failure Instructions

Installation

The SEL-UCIP1 modules include one user-configurable DIP switch array (SW2), located at the card edge next to the extractor. In normal operation, all four switches are in the Off position. In the unlikely event of corrupted software, you may need to temporarily change the setting of Switch 1 for the failsafe mode override. You would be alerted to this problem if a System Recovery Upgrade Required fault was triggered after an upgrade, and the module had finished rebooting.

If a System Recovery Upgrade Required fault is triggered, you should first try using the alternate firmware (see Activating Alternate Firmware in the Selenio frame manual) and then attempt the upgrade again. If this second attempt fails, follow these steps to activate the failsafe mode:

1. Remove the module from the frame and then push Switch 1 to the On position.

Figure 11: DIP Switch Setting for Failsafe Mode

2. Reinsert the module.

3. Install the new module software using the Selenio user interface.

4. Remove the module, and then return Switch 1 to the Off position.

5. Reinsert the module.

The module is now running the new software.

Accessing MIBs

Management Information Base (MIB) files for all modules can be downloaded directly from any Selenio

MCP frame. MIBs are generated on a per-device basis. For example, if there are seven SEL-UCIP1 modules in a frame, only one of the seven MIBs is required, assuming all of the modules are using the same version of software. If the frame includes multiple modules of the same type, but different software versions, the module with the latest version should be used to generate the MIB.

If an older MIB is used with newer firmware (for example, an older version of firmware was used instead of the latest firmware), the new parameters added to the new version will not be available on the MIB, and thus, will not be accessible via the MIB.

Selenio SEL-UCIP1

Installation and Operation Manual Installation

Before downloading module MIBs, you must first download the InfrastructureNetwork.mib file. Copy the following into a browser to access the InfrastructureNetwork.mib:

http://<IP address>/InfrastructureNetwork.mib

<IP address> is that of the primary controller in the frame

Once any MIB file is downloaded from the frame, you should rename it immediately to prevent overwriting.

To download a specific module MIB file, copy this line into a browser:

http://<IP address>/mib/slot<slot#>/snmp.mib

<IP address> is that of the primary controller in the frame

<slot#> is the slot in the frame, as seen from the front

Selenio SEL-UCIP1

Installation and Operation Manual

Setting Up Your SEL-UCIP1

When first setting up the SEL-UCIP1, follow these steps:

1. Select all of the necessary options in the Module Configuration block. See Module

Configuration/AES67 Configuration (on page 25).

The Operational Mode setting determines whether you will operate in AES67 or Classic mode.

Under Module I/O Configuration, the options will depend on the Operational Mode setting.

2. Select all of the necessary options in the WAN Configuration and Status block. Three pages are accessible from a drop-down menu.

The General page has read-only parameters, plus a table parameter for configuring up to six IP

WANs.

The Status page has more read-only parameters.

The SFP+ page has transmit and receive settings.

3. Configure your SEL-UCIP1 based on settings you made in Step 1. See the following topics:



Classic Mode (on page 24 )



AES67 Mode (on page 24)

Classic Mode

Configure the IP Transmit Table and the IP Receiver Table. See the following topics:

• IP Transmitter (Table) (on page 32 )

• IP Receiver (Table) (on page 38)

These two tables have multiple pages accessible through the drop-down menu at the top of the screen.

When you have completed all pages, your SEL-UCIP1 is ready to go.

AES67 Mode

Configure the AES67 Tx Setup and AES67 Rx Setup pages. See the following topics:

• AES67 Tx Setup (on page 34 )

• AES67 Rx Setup (on page 47)

There are multiple pages accessible through the drop-down menu at the top of the screen that will need to be completed.

When you have completed all pages, your SEL-UCIP1 is ready to go.

Selenio SEL-UCIP1

Installation and Operation Manual Setting Up Your SEL-UCIP1

Deterministic Video/Audio Switching

In typical broadcast studio applications, switch commands received by the SEL-UCIP1 module need to be deterministic (time accurate). This is particularly important when devices on the network are controlled by Automation.

For the UCIP switch time to be time accurate, the Timestamp Offset parameter allows the switching time to be set. Due to the processing latency of the Software Defined Network Orchestrator (SDNO) software, Ethernet network, Selenio Controller and UCIP module, switch commands are sent sufficiently in-advance of the switch time to compensate for the delay in the system.

Deterministic switching requires addition of ST2059 protocol support to the SEL-UCIP1 module. The

Network-Based Timing and Synchronization (ST2059) protocol is transmitted to the module over the

SEL-UCIP1’s 10G Ethernet ports. These ports are exposed to the external network and can receive

ST2059 protocol messages. The module's software utilizes the ST2059 reference as a sync source to the frame synchronizer as well as providing output alignment.

Parameters

Module Configuration/AES67 Configuration

When you click on this block, a menu at the top of the parameter list has the following options and suboptions:

• General (on page 26 )

Selenio SEL-UCIP1

Installation and Operation Manual

• PTP/1588 (on page 28)



Control (on page 28 )



Status (on page 29)

General

Name Use this field to create a name for the module.

Setting Up Your SEL-UCIP1

Module I/O Configuration

Operational Mode

Module Fault Alarm Priority

Frame Reference Select

This parameter selects the configuration of SDI inputs and outputs, depending upon the licensed options. Possible values for the four- and eight-channel versions are the following:

Four-Channel

0 SDI in, 4 SDI Out

2 SDI In, 2 SDI Out (default)

4 SDI In, 0 SDI Out

CTR + 1 SDI In, 2 SDI Out

CTR + 3 SDI In

Eight-Channel

4 SDI In, 4 SDI Out (default)

6 SDI In, 2 SDI Out

CTR + 3 SDI In, 4 SDI Out

CTR + 5 SDI In, 2 SDI Out

Eight-Channel AES67

4 SDI In, 4 SDI Out (default)

CTR + 3 SDI In, 4 SDI Out

Use this parameter to enable either the AES67 mode, or Classic UCIP mode.

After the operational mode has been changed, a new parameter ("Confirm

Mode Change?") will appear. Click on "Confirm Mode Change and Reboot" to confirm the mode change. The module will then reconfigure itself and become available for use in about 5 minutes.

Module Faults cause the frame to take recovery actions according to the

Module Fail Action on the controller Redundancy page. The Module Fault

Alarm Priority sets the priority of module alarms on a scale of 1 to 10

(default is None).

Using this parameter, any enabled alarm (with a priority above or equal to the setting) triggers a text string indicating the alarm source. The module also signals the controller that the module has failed so that a backup module is activated, if available.

For more details, see Alarms (on page 50).

The SEL-UCIP1 module operates with either Primary or Secondary Frame

Reference. Primary Frame Reference is the default setting. If the module is installed in an MCP1 frame, the parameter must be set to Primary

Frame Reference.

Selenio SEL-UCIP1

Installation and Operation Manual Setting Up Your SEL-UCIP1

Reference Standard

Serial Number

This read-only parameter reports the current reference standard used by the frame.

The possible values are as follows:

• 1080p/50

• 1080p/59

• 1080p/60 Level A

• 1080p/60 Level B

• 1080i/50

• 1080i/59.94

• 720p/50

• 720p/59.94

• 525

• 625

•

Not Present

The value set in this control determines the CTR SDI output, and also the thumbnail image that appears in the user interface.

The selection made in the Module I/O Configuration parameter determines which of the following options are available:

• IP Receiver 1

• IP Receiver 3

• EXT SDI 1

• EXT SDI 3

• EXT SDI 5 (Classic UCIP only)

The content of IP Receiver 1 and IP Receiver 3 is determined by the Next

Source coordinates for each receiver channel, located in the IP Receiver

Table of the IP to SDI block.

This read-only parameter reports the serial number of the module, and is necessary when ordering a softkey option.

These read-only parameters report the versions of their respective components.

Software, ROM, and FPGA

Versions

Board and FPGA Temperature These two read-only parameters report the module's temperature and that of the FPGA in Celsius degrees.

In an ambient room temperature of 25° C, a typical Board Temperature is

34° C,and an FPGA Temperature is 42° C. If either the Board Temperature is greater than 80° C, or the FPGA Temperature is greater than 90° C, a warning alarm is triggered. If either the Board Temperature is greater than

90° C or the FPGA Temperature is greater than 100° C, the module is shut down to protect the electronic components from over-heating.

Selenio SEL-UCIP1

Installation and Operation Manual

Fan RPM

Setting Up Your SEL-UCIP1

The Revolutions Per Minute (RPM) of the FPGA fan blower are reported here. Typically the Fan RPM displays Off. If the FPGA Temperature becomes greater than 80° C, the fan blower will turn on. When the FPGA

Temperature drops below 70° C, the fan blower will turn off.

PTP/1588

The drop-down menu has the following sub-options, where all the parameters reside:

• Control (on page

28 )

• Status (on page 29)

CAUTION

When using PTP, the SEL-UCIP1 defaults to Slave mode. When putting the device into Master mode, be aware that SEL-UCIP1 is not suitable to be a master in a large network system.

Having an inappropriate master can create strange network behavior for other devices.

Control

Select Profile

PTP Mode

Options are:

• AES67

• SMPTE ST 2059

• IEEE 1588

• SMPTE ST 2059+AES67

• SMPTE ST 2059+AES67+IEEE 1588

Set PTP as slave mode only, or to Master/Slave (so it can be Master).

Domain Number The PTP domain that the UCIP will listen to

Announce Interval Announce interval will be 2 to the power of this value in seconds. For example, 0 is one second. The range is -3 to 1, and the default is 1.

Announce Receipt Timeout The number of announce Intervals that have to pass, before declaring a timeout. The range is from 2 to 10, with a default of 3.

PTP Timeout = AnnounceReceiptTimeout * announceInterval (in seconds as defined above).

Selenio SEL-UCIP1

Installation and Operation Manual

Network from

Master/Boundary Clock

Setting Up Your SEL-UCIP1

Compensates the OWD based on the network configuration from the PTP master or boundary clock to the SEL-UCIP1. Options include:

• 100M->1G->10G

• 100M->10G

• 1G->10G

• 10G->10G

Note that the control makes an assumption based on how the switch normally behaves internally. Use the OWD Offset parameter (below) to manually compensate.

OWD Offset

Enter a compensation value to adjust the OWD setting that comes from the Network From Master/Boundary Clock parameter (above). See AES67

Connections (see "Connecting to a PTP Source" on page 17) for more

information.

Master Parameters

Priority 1 and 2

PTP Step Select

Sync Interval

The priority 1 or priority 2 value when device is Master (the lower the value, the higher the priority).

When device is master, determines whether to send a "Follow up" message (two step) after the "Sync" message, or just the "Sync" message

(one step).

When device is master, the sync interval will be 2 to the power of this value in seconds. For example, -3 is 0.125 seconds. The range is from -7 to

-1 with a default of -3.

LogMinDelayReq Interval Adj Modifies the logMinDelayReqInterval sent to the clients. The logMinDelayReqInterval will be "SyncInterval +

LogMinDelayReqIntervalAdj" which is the average rate at which clients should send delay request messages to the UCIP when acting as master.

For example, if the Sync Interval was -3, and the LogMinDelayReq Interval

Adj was 1, then the logMinDelayReqInterval will be -2, and thus, clients should send delay request messages at an average rate of 1 every 250ms.

Status

All parameters on this page are read-only.

PTP Master IP Address

PTP Master Interface IP

Address

IP address of the master being listened to.

IP address of the local interface of the master being listened to.

Selenio SEL-UCIP1

Installation and Operation Manual

PTP Master UUID

Setting Up Your SEL-UCIP1

Universally Unique Identifier for the grandmaster.

PTP Master Offset

PTP Master Delay

PTP Master Present

The time difference between the master and the UCIP. A positive value indicates that the UCIP is ahead of the master.

The transmission latency for a message in one direction.

Reports if a remote master is presently being listened to.

UCIP Is Master

UTC Time

Reports if the UCIP is presently the master.

Reports the UTC time.

SDI Video Interface Configuration and Status

CTR SDI/EXT SDI 1 to EXT SDI 4

Input Status

The EXT SDI x Input Status read-only parameters report the detected SDI input formats. When CTR SDI is selected as an input source, the EXT SDI 1 input is disabled. Possible values for CTR SDI and EXT SDI x inputs include the following:

• 1080p/50

• 1080p/50 DL

• 1080p/59

• 1080p/59 DL

• 1080p/60

• 1080p/60 DL

• 1080i/50

• 1080i59.94

• 720p/50

• 720p/59.94

• 525

• 625

• Not Present

Note: If you are using an external router and performing switches between sources with the same video format, the Rx SDI Out freezes on the last good frame while the system is locking to the new source.

Selenio SEL-UCIP1

Installation and Operation Manual

EXT SDI 5 to EXT SDI 8 Output

Status

Setting Up Your SEL-UCIP1

These read-only parameters report the output video standard. Possible values include the following:

• 1080p/50

• 1080p/50 DL

• 1080p/59

• 1080p/59 DL

• 1080p/60

• 1080p/60 DL

• 1080i/50

• 1080i59.94

• 720p/50

• 720p/59.94

• 525

• 625

• Not Present

SDI to IP

This block has three sub-blocks:

• Video Tx (on page

31 )

• AES67 Tx Setup (on page 34)

• AES67 Tx (on page 36)

Video Tx

IP Transmitter (Table)

Transmit Interface

Allocated Video Bandwidth

(Mbps)

See IP Transmitter (Table) (on page 32).

The Transmit Interface parameter has two options: Primary Only and

Primary+Secondary. When set to Primary+Secondary, this control enables seamless switching (SMPTE 2022-7).

If you select Primary+Secondary, the FEC function is disabled for all Tx channels. FEC may be enabled only when Primary Only is selected.

This parameter is available in both Classic and AES67 modes.

This read-only parameter reports the cumulative allocated bandwidth for all of the IP Transmitter channels that are enabled. By contrast, the

Allocated Channel Bandwidth under the FEC tab refers only to that particular IP Transmitter channel's data bandwidth.

This parameter is available in both Classic and AES67 modes.

Selenio SEL-UCIP1

Installation and Operation Manual

IP Transmitter (Table)

Setting Up Your SEL-UCIP1

Click the IP Transmitter Table button to reveal the table parameters. These are divided into four groups, selected from the drop-down menu in the top right:

• General (on page

32 )

• IP WAN Primary and Secondary (on page 33)

• FEC (Classic UCIP) (on page 34)

General

The IP Transmitter Table reveals the following parameters under the General heading:

SDI Source

SDI LOS

This read-only parameter indicates which HD-BNC input connector (or CTR

SDI source) is assigned to this IP Transmitter channel.

Enter a value in this field to identify the transmitter channel. Tag

IP Transmitter Enable

Video Timestamp When enabled, this parameter includes video timestamp in the SMPTE

2022-6 header.

Maximum Transmission Rate Set the Maximum Transmission Rate to SD: 270 Mb/sec or HD: 1.5 Gb/sec for this IP Transmitter channel.

Since there are up to six SDI inputs on a SEL-UCIP1 module, it would be possible for the video bandwidth to exceed the 10G Ethernet bandwidth.

To prevent this from occurring, the Maximum Transmission Rate parameter makes it possible to set the maximum bandwidth allowed for each SDI input. The total SDI bandwidth for all six SDI inputs must not exceed 9 Gbits per second (Gb/s). If the transmission rate detected for an

SDI input is greater than the selected Maximum Transmission Rate, this channel is automatically disabled to prevent corrupting the other IP

Transmitter channels.

Channel Bandwidth Status

Use this parameter to enable this IP Transmitter channel. Each of the IP

Transmitters must be enabled separately. IP Transmitter Enable allows the SDI Source signal to be encapsulated into Ethernet frames and sent out through the SFP+ ports.

This read-only parameter confirms that the bandwidth is appropriate for the signal on this channel. If the SDI input’s transmission rate exceeds the

Maximum Transmission Rate, this status parameter will report Channel

Disabled.

Possible values for this channel's loss-of-signal (LOS) parameter are No

Fault or Fault. If an SDI signal is not detected on this IP Transmitter's SDI input, a Fault is reported.

Selenio SEL-UCIP1

Installation and Operation Manual

SDI Standard

Setting Up Your SEL-UCIP1

This parameter reports the SDI standard received by the encapsulator on this IP Transmitter channel.

EDH or CRC Errors The total number of the input channel's EDH or CRC errors is reported here.

Clear EDH/CRC Error Counter Click the Apply button to reset the status values for this IP Transmitter channel.

IP WAN Primary and Secondary

The following parameters are shown when the IP Transmitter (table) drop-down menu is set to either IP

WAN Primary or IP WAN Secondary.

Destination IP Address

Destination UDP Port

WAN Select

IP WAN Address

WAN VLAN ID

Type of Service

Time to Live

Destination MAC Address

Use this field to set the address of the destination IP device.

UDP stands for Datagram Protocol. Use this field to set the Destination

Port number. Range is 1 to 65535.

Use this parameter to set the source WAN IP address for transmitting this

IP Transmitter's data. Possible options are WAN 1 to WAN 6.

This read-only parameter reports the source IP WAN Address for the designated IP Transceiver channel.

This read-only parameter reports the source WAN VLAN ID for the designated IP Transmitter channel.

The value set in the Type of Service field determines the value sent in the

Type of Service byte in the IP header of the Data Ethernet packets. The handling of the Type of Service byte in the IP header is dependent on the network equipment.

Configure the Time to Live parameter to avoid loops in network traffic.

The value in this field specifies the number of hops through network equipment before packets are discarded. This is used to avoid packets being continuously passed around in a loop due to a misconfiguration of the network.

This read-only parameter reports the MAC address of the receiver's primary or secondary SFP+ port. If no destination is using this IP

Transmitter's Destination IP Address, the parameter reports DST

Unreachable.

Selenio SEL-UCIP1

Installation and Operation Manual

FEC (Classic UCIP)

Setting Up Your SEL-UCIP1

This feature is available in the Classic UCIP mode. When AES67 mode is enabled, FEC is not available.

The following parameters are shown when the IP Transmitter (table) drop-down menu is set to FEC.

FEC Level

FEC Order (4-255)

The FEC Level parameter sets the forward error correction to None, Low,

Medium, High, or Custom. When Low, Medium, High, or Custom is selected, additional FEC parameters become visible.

When the FEC Level is set to None, forward error correction packets are not generated for the designated IP Transmitter channel. When the FEC

Level is set to: Low, Medium or High, the FEC Order, FEC Period and FEC

Row Enable parameters are not accessible (greyed out). Setting the FEC

Level to Custom allows you to enter FEC Order and FEC Period values, and also to Enable FEC Row parameters.

Possible values are 4 to 255.

FEC Period (4-1020)

FEC Row Enable

Possible values are 1 to 1020, depending on the setting of the FEC Row

Enable parameter.

• With FEC Row Enable set to On, the FEC Period range is 4 to 1020.

• With FEC Row Enable set to Off, the FEC Period range is 1 to 1020.

Note: The following Row x Period products cannot be violated:

- 270Mbps SD-SDI: Maximum Row x Period = 1500

- 1.5Gbps HD-SDI: Maximum Row x Period = 3000

Select On to enable the FEC Row function. Refer to the SMPTE-2022-5 standard for a more detailed explanation of FEC Order, Period and Row

Enable parameters.

Allocated Channel Bandwidth

(Mbps)

This read-only parameter reports the bandwidth that can be consumed by the designated IP Transmitter channel. This value is calculated by the SEL-

UCIP1 module, and it represents the sum of the bandwidth used by FEC, the Maximum Transmission Rate, plus some protocol overhead required by the module.

AES67 Tx Setup

The AES67 Tx Setup block has parameters divided into the following groups, accessed by a drop-down menu:

• De-Embedded Setup (on page

35 )

• Network Setup (on page 35)

• Enable/Disable Setup (on page 35)

Selenio SEL-UCIP1

Installation and Operation Manual

De-Embedded Setup

AES67 Tx

AES67 Tx (Table) (on page 35)

Setting Up Your SEL-UCIP1

Auto Map Audio Channel Start This control selects the starting point for auto mapping of audio channels.

The default starting point is DMB 1 Ch 1A.

Auto Map Audio Channels This feature automatically configures the audio channel mapping. Possible values are -- (default), Set All Mono, and Set All Stereo.

AES67 Tx (Table)

Number of Channels

Audio Channel n (one parameter for each channel inserted into this AES67 stream)

Network Setup

Primary and Secondary

Starting IP Address

Use this parameter to select the number of audio channels (1 or 2) to insert into this AES67 stream (default is 2).

Note: For compatibility purposes, the SEL-UCIP1 can accept up to 8 channels of incoming AES67 audio, but only processes and outputs the first two.

Use these controls to select the first audio channel for this AES67 stream.

Options are De-Embedders 1 to 4, Channels 1A to 8B. Default is DMB 1 Ch

1A.

These two controls set the IP address starting point for automatic assignment. The default is 239.1.1.1.

Primary/Secondary UDP Port Use this control to select a UDP port for automatic assignment. This UDP port will be assigned to all selected AES67 transmitters.

AES67 Tx IP Address Set

Starting Channel

AES67 Tx IP Address Set

Number of Channels

Auto Map IP Tx

This control sets the starting channel to which IP addresses will be assigned, in a range from 1 to 64, with a default setting of 1.

Use this parameter to select the number of channels to which IP addresses will be assigned. (Range is 1 to 64; default is 64.)

The Auto Map IP Tx automatically configures the audio IP transmitter settings. Click Apply to enable all of the settings on this page.

Enable/Disable Setup

Automatic Enable/Disable

Action

Enables or disables a group of AES67 Tx channels.

Selenio SEL-UCIP1

Installation and Operation Manual

AES67 Tx Enable/Disable

Starting Channel

Setting Up Your SEL-UCIP1

Chooses the starting AES67 Tx channel to enable or disable.

Sets the number of AES67 Tx channels to disable. AES67 Tx Enable/Disable

Channels

AES67 Tx Auto Disable

AES67 Tx Master Enable

Automatically disables a group of AES67 Tx channels.

Enables all AES67 Tx channels.

Disables all AES67 Tx channels. AES67 Tx Master Disable

AES67 Tx

AES67 Tx (Table)

Audio Bit Width

Packet Time

AES67 Tx Primary and

Secondary Type of Service

See AES67 Tx (Table) (on page 36)

Use this control to configure the audio sample bit width. Possible options are 16 bits and 24 bits (default).

Set the Packet Time with one of the following values: 250us, 333us, and

1ms, with a default of 1 ms.

Configure the type of service with this parameter. The range is 0 to 255, with a default of 2.

AES67 Tx Primary and

Secondary Time to Live

AES67 Tx (Table)

Tag

This parameter configures the time to live for IP packets. The range is 1 to

255, with a default of 64.

Use this field to set the name for this AES67 IP transmitter.

AES67 IP Transmitter Enable This parameter enables each of the 64 AES67 IP transmitters.

WAN Select There are six available WANs, selectable using this control. Default is WAN

Primary and Secondary IP

WAN Address

These parameters report the address of the IP WAN shown in the WAN

Select parameter.

Primary and Secondary WAN

VLAN ID

These two read-only parameters report the ID of the WAN VLAN.

Primary and Secondary

Destination IP Address

Use these two fields to set the address of the destination IP device.

Selenio SEL-UCIP1

Installation and Operation Manual

Primary and Secondary

Destination UDP Port

Setting Up Your SEL-UCIP1

Use these two fields to set the Destination UDP port number.

IP to SDI

This block has three sub-blocks:

• Video Rx (on page

37 )

• AES67 Rx (on page 46)

• AES67 Rx Setup (on page 47)

Video Rx

IP Receiver

See IP Receiver (Table) (on page 38).

Packet Delay Variation

(PDV) (ms)

Use this control to set the maximum network IP jitter (Packet Delay Variation) in milliseconds. The range is 0 to 50 ms in Classic mode or 0 to 10 in AES67 mode, with a default of 1 ms.

Seamless Max Path

Differential (ms)

This control sets the maximum path differential for seamless protection (in milliseconds). The range is 0 to 150 ms in Classic mode or 0 to 10 in AES67 mode, with a default of 1 ms.

Minimum Required

Playout Delay (ms)

Playout Delay

This read-only parameter reports the minimum required playout delay level in milliseconds. The recommended playout delay range is 0 to 260 ms in classic mode, or 0 to 10 ms in AES67 mode.

Note: If both Packet Delay Variation (PVD) and Seamless path Differential are set to a high rate, the playout delay requirement may be greater than the maximum allowed by SEL-UCIP1, especially in AES67 mode. If you encounter this problem, lower the setting on either one or both of the PDV and Seamless Path Differential parameters.

This parameter sets the desired nominal delay, with a range of 1 to 320 ms in

Classic mode or 1 - 10 in AES67 mode (8 ms is the default). The Playout Delay value should be equal to--or greater than--the Minimum Required Playout Delay (ms) status value. The Minimum Required Playout Delay is the sum of the Packet Delay

Variation (PDV) and Seamless Max Path Differential parameter values, plus some overhead value.

Warning: During the adjustment of this parameter, the video output will have disturbances.

Buffer Mode

When left at its default setting of TR04 Mode, the module automatically locks to incoming PTP. Alternatively, you can manually force it to non-TR04 mode, where the module will ignore incoming PTP.

Selenio SEL-UCIP1

Installation and Operation Manual

IGMP Leave Delay

Setting Up Your SEL-UCIP1

When in Make After Break Switch Mode, as set in IP Receiver (Table) > General (on

page 39), this value (measured in milliseconds) is how long this device will wait for

the current stream to disappear before timing out on the Next Source switch.

IP Receiver (Table)

The IP Receiver table has the following sub-sections accessed through the drop-down menu:

• General (on page

39 )

• Status (on page 42)

• Audio DMB Status (see "Audio Control/Status" on page 44)

• IP WAN Primary and Secondary (see "IP WAN (Primary and Secondary)" on page 44)

• FEC (on page 45)

• Video Sync (on page 45)

• Audio Sync (on page 45)

• Audio Embedding (on page 46)

Before configuring the values in the primary and secondary IP Receiver tables, ensure that you are aware of the following conditions:

• WAN Select reflects both the primary and secondary as one parameter choice (where in the IP WAN table, the primary and secondary interfaces can be specified together).

• Values that are entered into the Next IP Address and Next UDP Port fields (and that are then activated using Take > Apply) will appear in the Next Source field. Additionally, values can be changed directly in the Next Source field. In both cases, the result is reflected in the "Current" IP

Address and UDP Port parameters that appear on the same GUI page. The Next Source field will populate its values back to the Next IP Address and Next UDP Port fields

• Ensure that you configure all primary and secondary WANS before inserting any Next Source values.

Once you have entered the values in the Next Source field, the configurations take effect when you press Tab or Enter on your keyboard, or when you click outside of the field.

• Next Source values must be unique for IP Address, UDP Port, and VLAN ID, on both primary and secondary WANs, and at least one change is needed for one of the three parameters in both primary and secondary. Therefore there must be at least one change in the primary, and one change in the secondary for the switchover to occur. Exception: If another SEL-UCIP1 receiver has the exact same settings, the switch is allowed

• You can choose to disable the secondary filtering. There are three ways to do this: remove the secondary entry in the Next Source field, set the secondary Next Source value at 0.0.0.0:0, or simply insert the primary:port values in the field.

• The IP Receive Port Numbers +2/+4 of the media UDP Port are reserved for FEC functions. You cannot enter a value that is +2/+4 of an existing IP Receive Port Number with the same chosen IP

Address and VLAN ID.

• The primary IP Address, IP Receive Port Number, and VLAN ID (whether they are multicast or unicast) cannot be the same as the secondary IP Address, IP Receive Port Number, and VLAN ID. An

IP Address value of 255.255.255.255 is invalid in all configurations.

• The Source and Destination IP Addresses and UDP Port parameter values are not restricted by the module. (For example, the Destination IP Address will allow you to set an abnormal value of

224.0.0.0.) Ensure that you use caution when entering values in these fields.

Selenio SEL-UCIP1

Installation and Operation Manual Setting Up Your SEL-UCIP1

• When setting a new IP address and UDP Port on an IP Receiver, the SEL-UCIP1 will attempt a clean

& quiet switch to the new video signal. However, if the requested video signal isn’t present at the module’s 10G network input at the time of the switch, that IP Receiver may output frozen or old video data until the new signal is present.

SDI Loopback Feature

Using the SDI Loopback feature, you can route any of the SEL-UCIP1 SDI inputs to any of the SDI outputs in the same module. To activate this feature in the user interface, enter a value in the IP Address, UDP

Port, and (optionally) VLAN ID field in an IP Receiver channel. (These values must match the IP Address,

UDP Port, and optional VLAN ID fields of an IP Transmitter channel.)

Once these values are matched, the Transmitter channel’s data is routed to the IP Receiver channel’s output. This routing includes video and audio frame synchronization of the looped-back SDI input.

Example

An IP Transmitter has the following settings:

• Primary Destination IP Address: 239.1.1.1

• Primary Destination UDP Port: 1100

Enter the same values for any IP Receiver as shown:

• Next Primary IP Address: 239.1.1.1

• Next Primary UDP Port: 1100

In this case, since the receiver values match those of the transmitter, the SDI input for the given IP

Transmitter will be routed to the SDI output of the given IP Receiver within the same physical module.

This concept may also be extended to include secondary IP addresses, UDP ports and VLAN IDs.

If a unicast address is entered into the IP transmitter destination IP address, it is not possible to loopback that video signal unless the IP transmitter destination IP address matches the module’s own IP

WAN IP address.

For example, on an IP Transmitter channel an address of 192.168.1.1 is entered. In order to loopback that video source to an SDI output, the IP WAN’s IP address must also be set to 192.168.1.1. Then, in the

IP Receiver channel, if you enter 0.0.0.0 for the Next Primary/Secondary IP Address, the video signal loops back.

General

HD BNC Label

Tag

IP Receiver Enable

This read-only parameter indicates the HD-BNC connector that is enabled with the selected IP Receiver channel.

Enter a value in this field to identify the IP Receiver channel.

Select On or Off to enable or disable this IP Receiver channel. Each of the

IP Receivers must be enabled separately.

Selenio SEL-UCIP1

Installation and Operation Manual

Max Receive Rate

Setting Up Your SEL-UCIP1

Three values are available:

• SD: 270Mbps

• HD: 1.5Gbps

• 3G: 3.0Gbps

Max Receive Rate is available in AES67 mode only.

Channel Bandwidth Status This read-only parameter indicates whether the bandwidth is available.

Switch Mode This read-only parameter displays the switch mode for the selected channel. Make Before Break is the preferred option, but can only be used when the current Max Receive Rate (above) multiplied by two and added to the Max Receive Rate of all the other channels is less than 10G.

In Make Before Break mode, the "Next Source" stream is acquired by

IGMP Joins. The previous stream is removed after a clean transition of video and audio by IGMP Leaves. There must be enough bandwidth remaining on the 10G Ethernet Links to have the "Next Source" stream to be present alongside the current stream. If there is an over subscription of bandwidth, the other channels will be disrupted due to Ethernet packets being dropped.

In Make After Break mode, the current stream is lost by IGMP Leaves. If you receive an error message under "Switch Error" indicating that the switch failed due to timeout, change the IGMP Leave Delay parameter

value (see Video Rx (on page 37)), then perform the switch again by

clicking Take. Assuming the timeout does not occur, after waiting for the delay indicated in the IGMP Leave Delay parameter and for the current stream to be lost, the "Next Source" stream will be acquired by IGMP joins.

There will not be a clean transition of video and audio in this switch mode.

Make After Break will only work if the amount of bandwidth being received by the device can dynamically change due to IGMP Leaves/Joins or with SDNO. Otherwise Make After Break will always fail with a timeout message.

Since Make Before Break switch mode is more desirable than Make After

Break, the device may decide to perform a Make Before Break on a channel that is indicated as Make After Break. This is possible due to receiver channels sharing the same IP stream. Shared IP streams do not consume any more bandwidth than when the IP stream is non-shared.

Selenio SEL-UCIP1

Installation and Operation Manual

WAN Select

Setting Up Your SEL-UCIP1

This control sets the WAN for the designated IP Receiver channel. Six

WANs are available. WAN Select must be configured and selected before performing a Next Source switch. Changing the option in WAN Select to another WAN will not reset the Next Source switch.

To use this control, first configure the WAN Select parameter for all the IP

Receivers. Then enter the Next Source addresses and ports for each IP

Receiver.

Clicking Take > Apply similarly applies the changes to a particular WAN.

Selected Primary and

Secondary IP Address

Selected Primary and

Secondary VLAN ID

Current Primary and

Secondary IP Address

These read-only parameters report the IP WAN IP Address for the designated IP Receiver channel.

These read-only parameters report the IP WAN VLAN ID for the designated

IP Receiver channel.

Current Primary and

Secondary UDP Port

Current Primary and

Secondary VLAN ID

This read-only parameter displays the IP address values that you entered in one of two places.

• If the configuration is unicast, the values entered in the IP WAN table appear here.

• If the operation is multicast, the Next Address value appears here.

These read-only parameters report the Primary and Secondary IP addresses of the four IP Receiver channels.

These read-only parameters report the VLAN ID values entered in the IP

WAN table.

Next Primary and Secondary IP

Address

The values entered in these fields appear in the Next Source field when you select Take > Apply. At that point, they become the Current Primary

and Secondary IP Addresses.

Next Primary and Secondary

UDP Port

Take

These values populate the Next Source field when you select Take >

Apply.

Click the Apply button to activate all of your changes to this IP Receiver channel.

Selenio SEL-UCIP1

Installation and Operation Manual

Next Source

Setting Up Your SEL-UCIP1

This is a read/write parameter that sets the primary and secondary source

IP addresses for each receiver channel. Values that are entered into the

Next IP Address and UDP Port fields and that are then activated (using

Take > Apply) will appear in the Next Source field. Additionally, values can be changed directly in the Next Source field. In both cases, the result is reflected in the "Current" IP Address and UDP Port parameters that appear on the same GUI page.

If values for an IP Address and UDP Port combination are entered when there isn’t an actual source in the incoming 10G feed, the module will either freeze or output black until the requested feed is available.

The format for this parameter is: Primary IP address:Primary UDP

Port;Secondary IP address:Secondary UDP Port. For example,

224.1.1.1:11000;224.1.1.2:12000

Switch Error Indicates whether an error has occurred on the recent switch.

Switch Status This read-only parameter confirms the success of the switch to the next source. The possible values are: Ready, Switching, Switch Complete, and

Switch Failed.

Timestamp Offset The offset is measured in video samples.

Status

If the IP Receiver channel has been set to an SDI Loopback source, all of the parameters under the

Status and IP WAN Primary/Secondary menus will be greyed out, except for the SDI Standard.

Selenio SEL-UCIP1

Installation and Operation Manual

SDI Standard

Setting Up Your SEL-UCIP1

This parameter detects the received SDI standards. Possible values are:

• 1080p/50

• 1080p/50 DL

• 1080p/59

• 1080p/59 DL

• 1080p/60

• 1080p/60 DL

• 1080i/50

• 1080i/59.94

• 720p/50

• 720p/59.94

• 525

• 625

• Not Present

Note: If you are using an external router and performing switches between sources with the same video format, the Rx SDI Out freezes on the last good frame or reverts to black, depending on the setting of the Loss of

Video Mode parameter (Black or Freeze) while the system is locking to the new source.

RTP Timestamp Difference The RTP Timestamp Difference reports the current time difference (in milliseconds) between the primary and secondary network inputs, providing information about how much of the seamless switching buffer is being used. This should be considered when setting for the size of the seamless switching buffer.

Buffered Packets

Packet Interval

This read-only parameter reports the number of IP packets currently buffered in the memory.

This parameter reports the timestamp difference between two consecutive sequence number packets.

Seamless Protection Status This read-only parameter reports the presence of seamless protection. In other words, it confirms the ability of the receiver to reconstruct the video feed from two separate network sources--without any errors or interruptions--if one of the feeds encounters packet loss.

The Seamless Protection Status parameter will report Not Present if either only one SFP+ port has an SFP+ module plugged into it or if the IP

WAN Address or UDP Port parameter for one of the SFP+ ports is not set up correctly.

Received Valid IP Packets This read-only parameter reports the number of valid IP packets received by this IP Receiver channel.

Selenio SEL-UCIP1

Installation and Operation Manual

Corrected Packets

Setting Up Your SEL-UCIP1

The number of corrected packets in this IP Receiver channel is reported here.

Duplicate Packets

DDR Buffer Overflow

Missing Packets

This field reports the number of duplicate packets for this IP Receiver channel.

This parameter detects an overflow of the DDR buffer on this IP Receiver channel.

Use this read-only parameter to track the number of missing packets on the selected IP Receiver channel.

Out of Range Packets This field reports the number of out-of-range packets for this IP Receiver channel.

If this value is increasing, it may indicate that the packets on either the

Primary or Secondary network inputs are significantly delayed, relative to packets received on the other network input.

Switch Count This parameter reports the number of IP switches that have taken place since the module’s start. Range is 0 to 1000000.

Clear Packet Counters Click the Apply button to clear all of the counters for this IP Receiver channel.

Audio Control/Status

These status messages report whether the IP Receiver channel has audio errors in the following categories:

• Groups 1 to 4 Parity Error

• Groups 1 to 4 Error Correction Code (ECC) Error

• Groups 1 to 4 Data Block Number (DBN) Error

• Groups 1 to 4 Checksum Error

IP WAN (Primary and Secondary)

These read-only parameters report numerical values for the designated IP Receiver channel.

Type of Service

Time to Live

Reordered Packets

Status as read from Ethernet frames on the IP Receiver channel.

Reports if the IP-to-SDI de-encapsulator is reordering the sequence of

Ethernet frames received on the IP Receiver channel.

Selenio SEL-UCIP1

Installation and Operation Manual

Valid Packets

Setting Up Your SEL-UCIP1

Increments when the IP-to-SDI de-encapsulator determines if a packet it has received is valid. During normal operation this parameter increments.

Clear Packet Counters Press the Apply button to reset all of the read-only WAN IP Primary and

Secondary values.

FEC

The following FEC values are reported for their respective IP Receiver channel, and are visible when FEC packets are detected on the IP Receiver channel.

• Column FEC

• Row FEC

• FEC Order

• FEC Period

Video Sync

Video Frozen This read-only parameter reports whether the video for this IP Receiver channel is frozen.

Loss of Video Mode Use this parameter to set the behavior of the designated IP Receiver channel in the event of loss of video. Options are: Freeze (default) and

Black.

Audio Sync

SRC Status

SRC (1 to 8) Control

The characters in this read-only parameter each represent an audio sample rate converter. E = Engaged and B= Bypassed. Both the left and right audio channels of an audio pair are either Synchronized (Engaged) or not Synchronized (Bypassed). Non-PCM audio data must be Bypassed around the Audio Synchronizer; otherwise it will be corrupted.

These controls configure the operation mode of the sample rate converters. Options are Engage, Auto, and Bypass.

When an SRC Control parameter is set to Auto, the Audio Channel Status bits determine whether the audio data is PCM or non-PCM, and whether the audio data is passed through the Audio Sample Rate Converters (SRC).

The Engage option always forces the audio data through the audio SRC, and Bypass always forces the audio data around the audio SRC.

Selenio SEL-UCIP1

Installation and Operation Manual

Audio Embedding

Setting Up Your SEL-UCIP1

Audio Source Options are:

• Embedded Audio from 2022-Rx

• AES67 Rx

Audio Group (1 to 4) Pair (1 or

2) Control

The individual parameters make it possible to bypass Dolby E audio without de-embedding and re-embedding, thereby preserving the Dolby E header alignment. Setting these parameters to Process forces the audio data to be re-embedded from the audio synchronizers or audio bypass paths.

Note: This feature is available in Classic Mode only.

AES67 Rx

The parameters are divided into the following sections, accessible from the drop-down menu:

• General (on page 46 )

• Status (on page 47)

General

Tag Specifies a name for this AES67 IP receiver.

AES67 IP Receiver Enable

AES67 Rx Bit Width

Enables this AES67 receiver.

Identifies the sample bit width for this AES67 Rx stream.

AES67 Rx Number of Channels Indicates the number of audio channels present in this stream.

WAN Select

Selected (Primary or

Secondary) IP Address

Selected (Primary or

Secondar)y VLAN ID

Specifies the primary and secondary VLAN.

Reports the IP WAN specified IP address.

Reports the IP WAN specified VLAN ID.

Next (Primary or Secondary) IP

Address

Sets the next specified IP address.

Next (Primary or Secondary)

UDP Port

Sets the next specified UDP Port.

Apply Applies Next settings.

Selenio SEL-UCIP1

Installation and Operation Manual

Next Source

Timestamp Offset

Setting Up Your SEL-UCIP1

Use to select the next source for this receiver. Enter in the format Primary

IP:port;secondary IP:port. Use the IP address 0.0.0.0 for unicast primary/secondary IP addressing.

The offset is measured in video samples.

Status

Primary and Secondary

Received Packets

Reports the number of packets received in the stream.

Primary and Secondary Out of

Sequence Packets

Reports the number of packets received out of sequence.

Primary and Secondary Lost

Packets

Reports the number of lost packets.

Primary and Secondary

Duplicate Packets

Reports the number of duplicate packets.

Primary and Secondary Buffer

Delay

Reports the buffer delay (audio samples).

Primary to Secondary Skew Reports the difference in latency between primary and secondary for

AES67 audio.

Switch count Reports the number of IP switches that have taken place since module start.

Clear Packet Counters Clears the packet counters for the channel.

AES67 Rx Setup

The parameters are divided into the following groups, accessible from a drop-down menu:

• Network Setup (on page

47 )

• Enable/Disable Setup (on page 48)

Network Setup

(Primary and Secondary)

Starting IP Address

These two controls set the IP address starting point for automatic assignment. The default is 239.1.1.1.

Primary/Secondary UDP Port Use this control to select a UDP port for automatic assignment.

Selenio SEL-UCIP1

Installation and Operation Manual

AES67 Rx IP Address Set

Starting Channel

Setting Up Your SEL-UCIP1

This control sets the starting channel to which IP addresses will be assigned, in a range from 1 to 64, with a default setting of 1.

AES67 Rx IP Address Set

Number of Channels

Auto Map IP Rx

Use this parameter to select the number of channels to which IP addresses will be assigned. (Range is 1 to 64; default is 64.)

The Auto Map IP Rx automatically configures the audio IP transmitter settings. Click Apply to enable all of the settings on this page.

Enable/Disable Setup

Automatic Enable/Disable

Action

Enables or disables a group of AES67 Rx channels.

Chooses the starting AES67 Rx channel to enable or disable. AES67 Rx Enable/Disable

Starting Channel

AES67 Rx Enable/Disable

Channels

AES67 Rx Auto Disable

AES67 Rx Master Enable

Sets the number of AES67 Rx channels to disable.

Automatically disables a group of AES67 Rx channels.

Enables all AES67 Rx channels.

AES67 Rx Master Disable Disables all AES67 Rx channels.

WAN Configuration and Status

The parameters are divided into the following sections, selected from a drop-down menu:

• General (on page

48 )

• Status (on page 49)

• SFP+ (on page 49)

General

IP WAN (Table)

Primary and Secondary TX

Packets

Primary and Secondary Rx

Packets

See IP WAN (Table) (on page 49)

These read-only parameters report the number of transmitted IP packets on the primary and secondary interface (as reported from the MAC).

In these read-only parameters, the module reports the number of received IP packets on the primary and secondary interface (as reported from the MAC).

Selenio SEL-UCIP1

Installation and Operation Manual

Primary and Secondary

Payload Tx Rate

Setting Up Your SEL-UCIP1

This read-only parameter reports the payload transmission rate of the primary and secondary interface (as reported from the MAC).

Primary and Secondary

Playload Rx Rate

This read-only parameter reports the payload receive rate of the secondary interface (as reported from the MAC).

Primary and Secondary SFP+

Ethernet MAC Addr

IP WAN (Table)

The MAC Addresses for the Primary and Secondary 10G Ethernet ports are displayed in these two parameters.

The changes made in this table are reflected in the IP Transmitter and IP Receiver parameters, and therefore change those configurations. The settings have both Primary and Secondary values.

Before configuring the values in the primary and secondary IP WAN tables, ensure that you are aware of the following conditions:

• All of the IP Addresses must be unique.

• An IP Address value of 255.255.255.255 is invalid.

• The primary IP WAN subnets and Subnet Masks must be different than the secondary IP WAN subnets and Subnet Masks.

• The VLAN ID numbers must be different for each primary interface set (IP WAN 1, IP WAN 2, IP

WAN 3, etc.), but you can re-use those primary VLAN ID numbers in the secondary interface set.

• Settings in the IP WAN table will not be activated until you click the Apply button under Confirm

VLAN Values (the Apply button will then become grayed out).

Status

These read-only parameters report the following conditions:

• Primary and Secondary Received Packets (these values increment when an Ethernet packet is received by either the Primary or Secondary port.)

• Primary and Secondary Errored Packets (these values increment when an Ethernet packet is identified as a bad frame by either the Primary or Secondary port.)

• Primary and Secondary Discarded Packets (these values increment when an Ethernet packet is not accepted for any channels on either the Primary or Secondary port.)

All of these parameters are read from the IP-to-SDI de-encapsulator component.

In the Clear General Counters parameter, click Apply to reset the general statistics reports.

SFP+

Primary and Secondary SFP+

Transmit Signal

This parameter reports the status of the Primary and Secondary SFP+

Transmit Signal. Possible values are Unknown, None, Normal, Degraded, and Fault.

Selenio SEL-UCIP1

Installation and Operation Manual

Primary and Secondary SFP+

Received Power

Setting Up Your SEL-UCIP1

These read-only parameters displays the average optical power level detected by the optical receiver in the SFP+ module in dBm. This field can also report Unsupported, which indicates that the SFP+ module doesn't report the receiver power.

Primary and Secondary SFP+

Attributes

The type of installed SFP+ is reported in the parameter. The following SFP+ modules are supported:

• OP+SFP+TRMM+10G MM (multimode fiber)

• OP+SFP+TRSM+10G SM (single mode fiber)

• SEL+AOC+10G (direct attach optical SFP+ cable)

If the SFP+ module or Direct Attach Cable is not recognized, the manufacturer's name, part number, and revision level of the SFP+ is displayed (as read from the EEPROM in the SFP+ module).

Primary and Secondary SFP+

Data Transmit Enable

SFP+ Debug Menu

This On/Off control enables data transmission on SFP+ modules you have installed in the SEL-UCIP1 back module.

When this parameter is set to On, it causes a Debug menu to become visible in the drop-down menu. The Debug menu shows the state of the

10G PCS/PMA components status registers. This is useful in debugging Link connection issues.

Alarms

Table 5: SEL-UCIP1Alarms List

Alarm Name

Module Failure

Module Fault – Calibration Error

High Temperature Warning

Module In Failsafe

Primary and Secondary SFP+ Fault

Fan Fault

SDI Input 1 to SDI Input 6 Missing

2022-Rx Ch 1 to Rx Ch 4 Missing

DMB 1 to DMB 4 Grp 1 to Grp 4 Parity Error

DMB 1 to DMB 4 Grp 1 to Grp 4 ECC Error

DMB 1 to DMB 4 Grp 1 to Grp 4 DBN Error

10 (Major)

8 (Major)

4 (Minor)

0.0 s

Default Clear

Delay

0.0 s

5.0 s

2.0 s

Version 2.0 | Page 50

Selenio SEL-UCIP1

Installation and Operation Manual

Alarm Name

DMB 1 to DMB 4 Grp 1 to Grp 4 Checksum Error

2022-Rx Ch 1 to Ch. 4 Video Frozen

Total Bandwidth Would Exceed 10.002 Gb/s

Back Module Absent

Inner Module Absent

HW Write Error

Playout Delay Too Low

No ARP Response

Input SDI Rate Exceeds IP Tx 1 to Tx 6 Maximum

Transmission Rate

SDI Input 1to 6 CRC Error

SDI Input 1 to 6 Link B CRC Error

SDI Input 1to 6 EDH Error

Module Memory Fault

Seamless Protection Missing for IP Rx #1 to #4

CTR Input Missing

PTP Master Missing

PTP Not Locked

Video Switch Error

AES67 Input Missing

Seamless Protection Missing for AES67 Rx

5 (Minor)

10 (Major)

6 (Major)

5 (Minor)

6 (Major)

4 (Minor)

10 (Major)

4 (Minor)

8 (Major)

Setting Up Your SEL-UCIP1

Default Clear

Delay

Selenio SEL-UCIP1

Installation and Operation Manual Laser Safety for Fiber Optic Back Modules

Laser Safety for Fiber Optic Back

Modules

WARNING!

Use of controls, adjustments, and procedures other than those specified in this document may result in hazardous laser radiation exposure.

Optical fiber telecommunication systems use semiconductor laser transmitters that emit infrared light that is normally not visible to the human eye. Although a conventional laser produces a small beam of light, the power density is very high, and it can damage your eyes.

If a beam of laser light enters the eye, the eye magnifies and focuses the energy on the retina. The energy that reaches the retina can be as much as 100,000 times more than at the cornea and, as a result, it can burn the retina.

Laser transmission products are classified in four major groups (Class 1, 2, 3, and 4), according to their emissions and potential for causing injury. Fiber optic transmitter modules in this series are designated

Class 1.

Precautions for Enclosed Systems

In its normal operating mode, an optical fiber communication system is totally enclosed and presents no risk of eye injury. However, if the fiber optic cables that interconnect various components of an optical fiber disconnect or break, you may be exposed to laser emissions. Also, technicians may be exposed to laser emissions during installation and servicing.

Unlike some other laser designs, semiconductor lasers have a highly divergent beam that decreases rapidly with distance. The greater the distance, the less energy will enter the eye, and the less potential risk for eye injury.

WARNING!

Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at the energized fiber end.

Under normal operating conditions, optical fiber telecommunication systems are completely enclosed; nonetheless, observe the following precautions:

• Do not stare into optical connectors or broken fibers.

• Ensure technicians have satisfactorily completed an approved training course before performing installation or maintenance.

• Ensure there are appropriate warning labels near the optical ports of the modules.

Selenio SEL-UCIP1

Installation and Operation Manual Laser Safety for Fiber Optic Back Modules

Precautions for Unenclosed Systems

During service, maintenance, or restoration, an optical fiber telecommunication system is considered unenclosed. Under these conditions, follow the practices described below.

CAUTION!

Only authorized, trained personnel shall be permitted to do service, maintenance, and restoration.

1. Avoid exposing the eye to emissions from unterminated, energized optical connectors at close distances.

2. Ensure that only authorized, trained personnel use optical test equipment during installation or servicing.

3. Turn off all laser sources before scanning a fiber with an optical test set.

4. Keep all unauthorized personnel away from the immediate area of the optical fiber systems during installation and service.

For guidance on the safe use of optical fiber communication systems in the workplace, consult ANSI

Z136.2, American National Standard for Safe Use of Lasers in the U.S. or outside the U.S., IEC-60825,

Part 2.

Label

The SEL-UCIP1 is a Class 1 laser product when used with a fiber optic back module.

Figure 12: Label for Class 1 Laser Products

Inspecting and Cleaning Fiber Optic

Connections

When connecting fibers to a back module, ensure that you do not touch the end of the fiber, or allow it to become dirty. Small amounts of microscopic dust or other contaminants can seriously impair or disable a fiber optic network. If you touch the end of a fiber prior to connecting it to the back module, or otherwise allow it to become dirty, you must carefully inspect and clean the connection.

This table lists some typical contaminants of a fiber optic connection.

Selenio SEL-UCIP1

Installation and Operation Manual

Table 6: Typical Contaminants

Contaminant

Dust particle, 1 micron

Dust particle, 9 microns

Human hair

Comments

Laser Safety for Fiber Optic Back Modules

Can block up to 1% of the light transmission, creating a loss of 0.05 dB

Although microscopic, the particle can completely block the fiber core

Typically 50 to 75 microns in diameter

Oil

Film residues

Powdery coatings

Frequently caused by touching

Can accumulate from vapors or smoke

Can be left behind after water or other solvents evaporate

Important Points

• Before you begin cleaning, always inspect the fiber connections.

• Inspect and clean both fiber ends every time you make a connection.

• Keep a protective cap on unplugged fiber connectors.

• Do not touch the end of a fiber.

• Store unused protective caps in a clean resealable container, located nearby for easy access.

• Do not reuse cleaning tissues or swabs.

• Do not allow alcohol or another wet cleaning agent to dry on a fiber end.

• Never touch the dispenser tip of an alcohol bottle or any clean portion of a tissue or swab.

• Use care when handling the fiber; do not twist or pull.

• Keep your cleaning fluids away from open flame or spark.

Selenio SEL-UCIP1

Installation and Operation Manual Laser Safety for Fiber Optic Back Modules

The illustration shows the acceptable limits of defects in a fiber connection.

Figure 13: Fiber Optic Cross-Section

Inspection Procedure

To inspect and clean the fibers, follow these steps:

1. Ensure the fiber is not "live."

WARNING!

Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at an energized fiber end.

2. Inspect the fiber endface with a fiberscope.

3. If the fiber endface is clean, return to the installation instructions; if the connector is dirty, proceed to the dry cleaning instructions below.

Dry Cleaning Procedure

If you are using cartridge- or pocket-style dry cleaning tools, follow the manufacturer’s directions. If you are using lint-free wipes, follow these steps:

1. Fold the lint-free wipe four to eight times into a square, taking care to avoid touching the cleaning surface of the wipe.

2. Lightly wipe the fiber tip in the central portion of the lint-free wipe.

Selenio SEL-UCIP1

Installation and Operation Manual Laser Safety for Fiber Optic Back Modules

CAUTION: Do not scrub the fiber. Excessive rubbing will leave scratches.

3. Repeat the wiping action on another clean section of the wipe or a new wipe.

4. Inspect the connector again with the fiberscope.

5. If the connection is clean, return to the installation steps; if the connector is still dirty, proceed to the wet cleaning instructions.

Wet Cleaning Procedure

Using 99.8% isopropyl alcohol and lint-free wipes, follow these steps to wet clean the fiber:

1. Fold the wipe into a square, about 4 to 8 layers thick.

2. Moisten one section of the lint-free wipe with one drop of 99.8% alcohol, ensuring that a portion of the wipe remains dry.

3. Lightly wipe the fiber end in the alcohol-moistened portion of the lint-free wipe.

4. Immediately repeat the wiping action on the dry section of the wipe, removing any residual alcohol.

5. Inspect the fiber endface again, and if necessary, repeat the wet cleaning with another clean section of the lint-free wipe.

CAUTION!

Do not scrub the fiber. Excessive rubbing will leave scratches.

6. Dry clean any remaining residue, and then inspect the connector again.

7. If the contamination persists, repeat the dry and wet cleaning procedure until the endface is clean.

If the fiber end still remains dirty after repeated cleaning attempts, call Customer Service for further instructions; if the fiber end is clean, return to the installation instructions.

Selenio SEL-UCIP1

Installation and Operation Manual

Specifications

HD/SD-SDI Input Specifications

Table 7: HD/SD-SDI Input Specifications

Item

Specification

Number of Inputs

Connector Type

Up to 6 (bi-directional port shared with output)

HD-BNC

Specifications

Standard • 3G (AES67 mode only): SMPTE 424M (1080p50/59/60)

• HD: SMPTE 292M (1.485, 1.485/1.001 Gb/s)

• SD: SMPTE 259M-C (270 Mb/s, 525/625 component video)

Connector

(High-Density) HD-BNC

Impedance

75Ω

Signal Level

800 mV ± 10%

Return Loss

Equalization

• 3G (AES67 mode only): >18 dB, typical, to 1.5 GHz and > 10dB to 3 GHz

• HD: >18 dB, typical, from 5 MHz to 1485 MHz

• SD: >18 dB, typical, from 5 MHz to 270 MHz

• 3G (AES67 mode only): Adaptive cable equalization for >328ft (100m) typical, of Belden 1694A coaxial cable

• HD: Adaptive cable equalization for >492ft (150m) typical, of Belden

1694A coaxial cable

• SD: Adaptive cable equalization for >820 ft (250m) typical, of Belden

1694A coaxial cable

Note: All the unused output ports should have 75Ω terminators.

Selenio SEL-UCIP1

Installation and Operation Manual

HD/SD-SDI Output Specifications

Table 8: HD/SD-SDI Output Video Specifications

Item Specification

Number of Outputs

Connector Type

Up to 6 (bi-directional port shared with input)

HD-BNC

Standard

Connector

Impedance

Return Loss

Signal Level

DC Offset

Rise and Fall Time

Overshoot

Jitter

Specifications

• 3G (AES67 mode only): SMPTE 424M (3G), 1080p50/59/60

• HD: SMPTE 292M (1.485, 1.485/1.001 Gb/s)

• SD: SMPTE 259M-C (270 Mb/s, 525/625 component video)

(High-Density) HD-BNC

75Ω

• 3G (AES67 mode only): > 18 dB to 1.5 GHz and > 10 dB to 3 GHz

• HD: >15 dB, typical, from 5 MHz to 1485 MHz

• SD: >15 dB, typical, from 5 MHz to 270 MHz

800 mV ± 10%

0.0V ± 0.5 V

• 3G (AES67 mode only): <135 ps (20% to 80%)

• HD: <270 ps (20% to 80%)

• SD: 400 - 1500 ps (20% to 80%)

< 10% of amplitude (all outputs terminated)

• Timing jitter:

• 3G (AES67 mode only): <2 UI peak to peak

• HD: <1 UI peak to peak

• SD: <0.2 UI peak to peak

• Alignment jitter:

• 3G (AES67 mode only): <0.3 UI peak to peak

• HD: <0.2 UI peak to peak

• SD: <0.2 UI peak to peak

Selenio SEL-UCIP1

Installation and Operation Manual

SFP+ Specifications

OP+SFP+TRSM+10G Single Mode Optical Transceiver

Table 9: Specifications for OP+SFP+TRSM+10G Single Mode Optical Transceiver

Transmitter

Parameter Minimum Typical Maximum Unit

Specifications

Notes

Laser OMA Output Power -5.2 dBm 1

Laser Mean Output Power

Laser Off Power

Extinction Ratio

-8.2

3.5

Transmitter and Dispersion Penalty (TDP)

Center Wavelength 1260

Optical Return Loss Tolerance

Receiver

Parameter

Receiver Sensitivity (OMA)

Stressed Receiver Sensitivity (OMA)

Receiver Power Overload

Receiver Reflectance

Center Wavelength

+0.5

-30

3.2

1355

12 dBm dBm dB dB nm dB

Minimum Typical Maximum Unit

-12.6 dBm

-10.3

+0.5 dBm dBm

-12 dB

1260 1355 nm

Notes

1,2

Vertical Eye Closure Penalty 2.2 dB 3

Stressed Eye Jitter

RX_LOS (OMA) Assert

RX_LOS (OMA) De-Assert

0.3

-30

-17

UIp-p dBm dBm

RX_LOS (OMA) Hysteresis 0.5 dB 4

1. IEEE 802.3ae Clause 52 compliant

2. Measured with worst ER; BER<1E-12; 2E31-1 PRBS

3. Vertical eye closure and stressed eye jitter are test conditions for stressed sensitivity (OMA) measurement.

4. Loss of Signal (LOS) detection responds only to OMA and the indicator will respond unpredictably with the application of unmodulated optical power.

Selenio SEL-UCIP1

Installation and Operation Manual

OP+SFP+TRMM+10G Multi Mode Optical Transceiver

Specifications

Table 10: Specifications for OP+SFP+TRMM+10G Multi Mode Optical Transceiver

Transmitter

Parameter

Laser OMA Output Power

Minimum Typical

-4.3

Maximum Unit

dBm

Notes

Laser Mean Output Power

Laser Off Power

3.0 Extinction Ratio

Transmitter and Dispersion Penalty (TDP)

Center Wavelength 840

-1.0

-30

3.9 dBm dBm dB dB

Optical Return Loss Tolerance

Receiver

Parameter

Receiver Sensitivity (OMA)

Stressed Receiver Sensitivity (OMA)

Receiver Power Overload

860

12 nm dB

Minimum Typical Maximum Unit

-11.1 dBm

-7.5 dBm

-1.0 dBm

Notes

1,2

Receiver Reflectance

Center Wavelength 840

-12

860 dB nm

Vertical Eye Closure Penalty 3.5 dB 3

Stressed Eye Jitter

RX_LOS (OMA) Assert

RX_LOS (OMA) De-Assert

0.3

-30

-12

UIp-p dBm dBm

RX_LOS (OMA) Hysteresis 0.5 dB 4

1. IEEE 802.3ae Clause 52 compliant

2. Measured with worst ER; BER<1E-12; 2E31-1 PRBS

3. Vertical eye closure and stressed eye jitter are test conditions for stressed sensitivity (OMA) measurement.

4. Loss of Signal (LOS) detection responds only to OMA and the indicator will respond unpredictably with the application of unmodulated optical power.

Selenio SEL-UCIP1

Installation and Operation Manual

SEL+AOC+10G

Table 11: Specifications for SEL+AOC+10G Optical Direct Attach Cable

Item Specification

Standard

Connector

Cable length

SFF-8431, SFF-8472

SFF-8432, SFP+ card-edge

10 meters

Bit Error Ratio (BER)

Power

Power Consumption

Case Operating Temperature

Range

Compliance

1E-15, tested with 2E31 – 1 PRBS

3.3V

< 1 Watt each cable end

0°C to 70°C

RoHS-6 compliant (lead-free)

Power Consumption

Table 12: Power Consumption

Item Specification

Module Power Consumption 40 W maximum

Propagation Delay

The minimum system latency for the SEL-UCIP1 is 1 frame, based on the following:

UCIP #1 SDI input > UCIP #1 SFP+ Tx > UCIP #2 SFP+ Rx > UCIP #2 SDI output.

Specifications

Selenio SEL-UCIP1

Installation and Operation Manual

Index

Accessing MIBs • 22

AES67 Mode • 24

AES67 Mode or Module • 12

AES67 Rx • 45

AES67 Rx Setup • 47

AES67 Tx • 36

AES67 Tx (Table) • 35, 36

AES67 Tx Setup • 34

Alarms • 50

Application Diagram • 18

Audience • 5

Audio Control/Status • 43

Audio Embedding • 45

Audio Sync • 44

Available Configurations • 9

Back Module • 16

Cables • 18

Classic Mode • 24

Classic Mode or Module • 12

Connecting to a PTP Source • 17

Contact Information • 2

Control • 28

De-Embedded Setup • 34

Deterministic Video/Audio Switching • 25

Dry Cleaning Procedure • 55

Enable/Disable Setup • 35, 47

Failsafe mode • 22

Features of the product • 11

FEC • 44

FEC (Classic UCIP) • 33

Firmware upgrades • 21, 22

Front Module • 13

General • 26, 31, 39, 45, 48

Index

HD/SD-SDI Input Specifications • 57

HD/SD-SDI Output Specifications • 58

Important Points • 54

Inspecting and Cleaning Fiber Optic Connections

• 53

Inspection Procedure • 55

Installation • 21

Introduction • 9

IP Receiver (Table) • 37

IP to SDI • 36

IP Transmitter (Table) • 31

IP WAN (Primary and Secondary) • 44

IP WAN (Table) • 48

IP WAN Primary and Secondary • 32

Label • 53

Laser precautions • 52, 53

Laser Safety for Fiber Optic Back Modules • 52

LEDs • 14

Main Features • 11

Manual Information • 5

Master Parameters • 29

Module Configuration/AES67 Configuration • 25

Network Setup • 35, 47

Obtaining Documents • 6

OP+SFP+TRMM+10G Multi Mode Optical

Transceiver • 60

OP+SFP+TRSM+10G Single Mode Optical

Transceiver • 59

Parameters • 25

Power Consumption • 61

Powering Up a Module • 21

Precautions for Enclosed Systems • 52

Precautions for Unenclosed Systems • 53

Preface • 5

Propagation Delay • 61

PTP/1588 • 27

Version 2.0 | Page 62

Selenio SEL-UCIP1

Installation and Operation Manual

Publication Information • 2

Purpose • 5

Restrictions on Hazardous Substances (RoHS) •

Revision History • 5

Safety precautions with lasers • 52

Safety Standards and Compliances • 7

SDI to IP • 30

SDI Video Interface Configuration and Status •

SEL+AOC+10G • 61

Setting Up Your SEL-UCIP1 • 24

SFP+ • 49

SFP+ Modules • 10

SFP+ Specifications • 59

Signal Flow • 19

Software upgrades • 21, 22

Specifications • 57

Status • 29, 42, 46, 49

Support Contact Information • 2

Trademarks • 2

Unpacking/Shipping Information • 6

Upgrade Failure Instructions • 22

Upgrading Module Firmware • 21

Video Rx • 37

Video Sync • 44

Video Tx • 31

WAN Configuration and Status • 48

Waste from Electrical and Electronic Equipment

(WEEE) • 7

Wet Cleaning Procedure • 56

Writing Conventions • 5

Index

Version 2.0 | Page 63

Anuncio