JVC DT-3D24G1 User's Manual

CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do
not remove cover (or back). No user
serviceable parts inside. Refer servicing
to qualified service personnel.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
MULTI FORMAT 3D LCD MONITOR
DT-3D24G1
INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is located on the rear of
the cabinet. Retain this information for future reference.
Model No.
Serial No.
DT3D24G1_EN.indb 1
:
:
DT-3D24G1
LCT2655-001A-H
11.1.25 0:53:40 PM
Safety Precautions
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH
AS VASES, SHALL BE PLACED ON THE APPARATUS.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has
been engineered and manufactured to assure your personal safety.
But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC
SHOCK OR FIRE. In order not to defeat the safeguards incorporated
into this product, observe the following basic rules for its installation,
use, and service. Please read these “IMPORTANT SAFEGUARDS”
carefully before use.
• All the safety and operating instructions should be read before the
product is operated.
• The safety and operating instructions should be retained for future
reference.
• All warnings on the product and in the operating instructions should
be adhered to.
• All operating instructions should be followed.
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V
(For U.S.A. and Canada) and AC 220 – 240 V (For European
countries, Asian countries, and United Kingdom).
The power cord attached conforms to the following power supply
voltage and countries. Use only the power cord designated to
ensure safety and EMC regulations of each country.
• Not all types of power cords are supplied to this product.
For U.S.A. and
Canada: AC 120 V
For European and
Asian countries:
AC 220 – 240 V
For United Kingdom:
AC 220 – 240 V
This plug will fit only into a grounded power outlet. If you are
unable to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose of the
grounded plug.
• This product should be operated only with the type of power
source indicated on the label. If you are not sure of the type of
power supply of your home, consult your product dealer or local
electric power company.
Warning:
• Do not use the same power cord for AC 120 V as for AC 220 –
240 V. Doing so may cause malfunction, electric shock or fire.
Note for United Kingdom power cord only
The plug of United Kingdom power cord has a built-in fuse. When
replacing the fuse, be sure to use only a correctly rated approved type,
re-fit the fuse cover. (Consult your dealer or qualified personnel.)
How to replace the fuse
Open the fuse compartment with the
blade screwdriver, and replace the
fuse.
Fuse
Warning:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
• Before connecting other products such as VCR’s and personal
computers, you should turn off the power of this product for
protection against electric shock.
• Do not use attachments not recommended by the manufacturer
as they may be hazardous.
• When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or equivalents. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
• Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
Under the following conditions,
1. Turn off the power.
2. Unplug this product from the wall outlet.
3. Refer service to qualified service personnel.
a) When the product emits smoke or unusual smell.
b) When the product exhibits a distinct change in performance
—for example, no picture or no sound.
c) If liquid has been spilled, or objects have fallen on the product.
d) If the product has been exposed to rain or water.
e) If the product has been dropped or damaged in any way.
f) When the power supply cord or plug is damaged.
• Do not install this product in the following places:
– in a damp or dusty room
– where the product is exposed to soot or steam, such as
near the cooking counter or a humidifier
– near heat sources
– where condensation easily occurs, such as near the window
– in a location exposed to direct sunlight or strong light
• Do not place this product on an unstable cart, stand, or table.
The product may fall, causing serious injury to a child or adult,
and serious damage to the product.
The product should be mounted according to the
manufacturer’s instructions, and should use a mount
recommended by the manufacturer.
• Do not use this product near water.
• Be sure to install the product in the place where proper
temperature and humidity are kept (→ “Operation environment”
on page 32).
This product becomes hot during its use. Take enough care
when handling the product.
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltages and
other hazards. Refer all service to qualified service personnel.
Do not use the product for a long time if the sound is distorted.
Use only the power source specified on the unit.
• AC power: 120 V/220 – 240 V, 50 Hz/60 Hz
• DC power: 24 V
• The AC power supply is controlled by turning on/off the
POWER switch on the rear panel. If the product is installed in a
place where you cannot easily turn on/off the POWER switch,
control the AC power supply by plugging/unplugging the power
cord into/from the AC outlet. In this case, install the product as
close to the AC outlet as possible, and leave enough space for
plugging/unplugging the power cord. If the product is installed
in a place where you cannot easily plug/unplug the power cord,
equip an easily accessible device to the wiring of the building
for turning on/off the power.
• When the product is left unattended and unused for a long
period of time, unplug it from the wall outlet and disconnect the
cable system.
• Do not overload wall outlets, extension cords, or convenience
receptacles on other equipment as this can result in a risk of
fire or electric shock.
• Use only the accessory cord designed for this product to
prevent shock.
The Mains Plug is used as the disconnect device, the disconnect
device shall remain readily operable.
To completely disconnect this apparatus from the AC mains,
disconnect the power supply cord plug from the AC receptacle.
2
DT3D24G1_EN.indb 2
11.1.25 0:53:41 PM
• Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from
overheating. These openings must not be blocked or covered.
• Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts,
which could result in a fire or electric shock.
• Never spill liquid of any kind on the product.
• Never place anything on the product. (Placing liquids, naked flames, cloths, paper, etc. on the product may cause a fire.)
• Do not apply any strong shock to the LCD panel. (Do not hit any object against it or push it with a sharp-pointed tool.)
• Do not put heavy objects on the product.
• Do not step on or hang on the product.
To prevent an accidental fall
VESA mounting holes
Fix the monitor to a wall by using strings.
Fixing the monitor
Attach the hook (not provided) to the VESA mounting holes on the
rear panel (use the two holes on the upper side) using M4 x 10
mm screws (not provided). Bind the hooks on the rear panel of the
monitor to a wall or a pillar using durable string.
Hook and screw (M4 x 10 mm)
(not provided)
Hook (not provided)
U.S.A. only
FCC NOTICE
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
IMPORTANT RECYCLING INFORMATION
This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your
community due to environmental considerations. For disposal or recycling information, please contact your local
authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE
EARTHING CONNECTION.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries
must be followed strictly.
3
DT3D24G1_EN.indb 3
11.1.25 0:53:41 PM
Safety Precautions (cont.)
European Union only
Dear Customer,
EMC Supplement
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
This equipment is in conformity with the provisions and protection
requirements of the corresponding European Directives. This
equipment is designed for professional video appliances and can be
used in the following environments:
• Controlled EMC environment (for example purpose built
broadcasting or recording studio), and rural outdoors environment
(far away from railways, transmitters, overhead power lines, etc.)
In order to keep the best performance and ensure electromagnetic
compatibility, we recommend to use cables not exceeding the
following length:
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and
electronic equipment should not be disposed
as general household waste at its end-of-life.
Instead, the product should be handed over to
the applicable collection point for the recycling
of electrical and electronic equipment for proper
treatment, recovery and recycling in accordance
with your national legislation.
By disposing of this product correctly, you will
help to conserve natural resources and will
help prevent potential negative effects on the
environment and human health which could
otherwise be caused by inappropriate waste
handling of this product. For more information about collection point
and recycling of this product, please contact your local municipal
office, your household waste disposal service or the shop where you
purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page http://
www.jvc.eu/ to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance
with applicable national legislation or other rules in your country for
the treatment of old electrical and electronic equipment.
Attention:
This symbol is
only valid in the
European Union.
Cable
Length
Power cord
(attached cable (H05VV-F 3 x 0.75 mm2))
2.0 m
Video signal cable (coaxial cable)
2.0 m
Audio signal cable (shielded cable)
1.5 m
DVI cable (shielded cable) with core filter
2.0 m
RS-232C cable (shielded cable)
(A straight cable with a D-sub 9-pin connector)
2.0 m
RS-485 cable (twist pair cable)
(A straight LAN cable)
2.0 m
REMOTE cable (twist pair cable)
(A straight LAN cable)
2.0 m
The inrush current of this apparatus is 15.44 ampere.
CAUTION
In case where the strong electromagnetic waves or magnetism are
near the audio cable or the signal cable, the sound or the picture will
contain noise. In such cases, please keep the cable away from the
sources of the disturbance.
Operating Precautions
The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display may occur. It is
recommended that you change images occasionally, activate the power saving function, or often turn off the power to reduce the load on the LCD panel. Charges
will apply for repairs resulting from deterioration due to the passage of time.
Caution for use of the product for many hours
In the case that you use the monitor for many hours, we recommend that you set “NO SYNC ACTION” in “SYNC FUNCTION” to “P.SAVE” in MAIN MENU. This
will reduce power consumption and relieve strain on the monitor. (→ page 22)
Caution for use of the product in the high temperature
Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may be damaged. This product is equipped with a
temperature sensor to give warning if the temperature becomes too high. If the temperature exceeds the range of normal use, “TEMP. OVER” is displayed, and
the power is turned off automatically if the temperature becomes any higher. In this case, move the product to a place of low temperature to let it cool down.
Maintenance
Screen
To avoid irreparable change in appearance of the screen such as uneven
color, discoloration, scratches, be careful about the following:
● Do not paste or stick anything using any glues or adhesive tapes.
● Do not write anything on the screen.
● Do not strike the screen with a hard object.
● Avoid condensation on the screen.
● Do not wipe the screen with any liquid such as water. In addition, wiping
the screen with water-diluted neutral detergent or solvent such as alcohol,
thinner, or benzine may affect the anti-reflection treatment of the screen.
● Do not wipe the screen forcefully.
Wipe stains off the screen with a soft cloth.
Ventilation openings
Cabinet
To avoid the deterioration or damages of the cabinet such as its paint’s
peeling away, be careful about the following:
● Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.
● Do not expose the cabinet to any volatile substance such as insecticides.
● Do not allow any rubber or plastic in contact for a long time.
● Do not wipe the cabinet forcefully.
Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained,
wipe it with a soft cloth soaked in water-diluted neutral detergent and wrung
well, then wipe with a soft dry cloth.
Glasses
Wipe the glasses with a dry, soft cloth.
Use a vacuum cleaner to get rid of the dust around the intakes (all the
openings). If a vacuum cleaner is not available, use a cloth and wipe it off.
Leaving the dust around the intakes may prevent proper temperature control
and cause damage to the product.
4
DT3D24G1_EN.indb 4
11.1.25 0:53:42 PM
Note: Be sure to read “When viewing in 3D” on page 12 for proper viewing beforehand.
Flicker-free 3D images by circular polarizing
Compatible with side-by-side and line-by-line formats to provide flicker-free 3D images
3D mixer converting L/R dual signals to a 3D mixed format
Mixes and converts images taken with a stereo camera rig to 3D images
Various functions useful on the spot
CAMERA ASSIST MENU: 7 menus useful in various shooting scenes
3D cursor: “Cursor mode” for displaying the visual difference between left and right eyes in
pixels/percentage; “Grid mode” for checking the visual difference by grid lines
Table of Contents
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Daily Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Viewing 3D images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic 3D principle
Compatible 3D format
When viewing in 3D
12
12
12
To view 3D images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To view existing 3D images
To view images taken by two cameras
13
13
Setting the CAMERA ASSIST MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Other 3D functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SCOPE button/lamp
3D CURSOR button/lamp
16
16
Setting the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MAIN MENU
SET-UP MENU
19
23
External control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Self-check program
31
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Available signals
Dimensions
33
34
5
DT3D24G1_EN.indb 5
11.1.25 0:53:42 PM
Installation
● Do not rest your arm on the monitor or lean against the monitor.
● Do not touch the LCD panel when installing the monitor.
● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.
● How to set up 1
● To detach the stand
You can tilt the monitor as follows.
When the monitor is not tilted
(0°), the guidelines align as
illustrated below.
Guidelines
Lay the monitor on a cloth with the LCD panel facing down to
prevent the LCD panel from being damaged.
Attachment screws
Screw holes for stand
attachment
Stand body
Monitor
Approx. 6°
0°
Approx. 6°
Stand
● To install the stand
● Be careful not to pinch your fingers in the gap between the
monitor and the stand.
● When the stand plate is attached to the lower position of the stand
body, you cannot tilt the monitor downward.
When attaching the stand to the monitor, insert the guides of
the stand plate into the guide holes on the monitor to place the
stand in the correct position. Then fix the stand firmly with the
attachment screws.
● How to set up 2
Guide holes
When the stand plate is attached to the higher position of the stand
body, you can place the monitor as illustrated below.
1
Remove the screws on the sides of the stand (see the following
illustration), and lift up the stand by approximately 148 degrees.
Screw (silver)
Approx. 148°
Guides
Monitor
Screw holes for stand
attachment
Stand plate
2
Attach the removed screws and place the monitor as illustrated
below.
Stand body
● To adjust the stand height
To change the stand height, detach the stand from the monitor.
Then, change the position of the stand plate according to the
stand height you want by choosing the screw holes to use.
● To place the monitor as shown in “How to set up 1” again, remove
the screws on the sides of the stand, align the guidelines, and then
reattach the screws.
Cautions
<Higher position>
<Lower position>
Screw holes
for higher position
Screw holes
for lower position
● When lifting up the stand...
- Lay the monitor on a cloth with the LCD panel facing down to
prevent the LCD panel from being damaged.
- Be careful not to pinch your fingers in the moving parts.
● Make sure of lifting the stand up until it stops (Approx. 148°);
otherwise the monitor may fall over.
● Place the monitor on a mat to avoid scratching the table surface.
● Do not lift up the stand when the stand plate is attached to the
lower position of the stand body.
Stand
plate
6
DT3D24G1_EN.indb 6
11.1.25 0:53:44 PM
Connections
Rear panel
4
Security slot
Attach a security
wire to this slot.
Note for connections
• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor
and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are complete.
• Refer also to the user manual of each piece of equipment.
8
1 DC IN 24V terminal
6 AUDIO (IN) terminals (pin jack)
Terminal for DC 24V power supply (Voltage range: DC 23.3V − DC 25.5V).
When using the DC 24V power supply (Voltage range: DC 23.3V − DC
25.5V), check the pin number, signal, and polarity of the DC IN 24V
terminal. A wrong connection may cause fire or injuries.
Input terminals for the analog audio signals.
● Use this terminal for the analog audio connection of the SDI.
When a superimposed signal (EMBEDDED AUDIO signal on
an SDI signal) is input, analog audio signals cannot be input.
7 AUDIO MONITOR OUT (OUT 1(L), OUT 2(R)) terminals (pin jack)
● When both AC power and DC 24V
power are connected, the AC power
has priority. When the AC power is
switched off, the power automatically
switches to the DC 24V power.
● Use the DC power equipped with LPS (Limited Power Sources).
● Use the DC 24V power that supplies 4.8 A.
2 AC POWER switch
Turns AC power on or off.
button (→ a on page 9) to use
the monitor after turning on the AC POWER switch.
● You need to press
3 AC IN terminal
AC power input connector. Connect the provided AC power
cord to an AC outlet.
● Attach the provided power cord holder to prevent
accidental disconnection of the AC power cord. (→ below)
Caution: Do not connect the power cord until all other
connections are completed.
Output terminals for the analog audio signal.
● The terminals emit the audio signals through the AUDIO (IN)
terminal or EMBEDDED AUDIO signals through the E. AUDIO
3G SDI/HD SDI/SD SDI (IN 1/L or IN 2/R) input terminal.
● The signal is output from this terminal only when the monitor is on or
in “P.SAVE” (power save) mode (→ “NO SYNC ACTION” on page 22).
● The EMBEDDED AUDIO signal...
– is decoded into an analog signal, then emitted.
– is emitted only when “SDI 1/L” or “SDI 2/R” is selected, and
when EMBEDDED AUDIO signals come in to the E. AUDIO 3G
SDI/HD SDI/SD SDI (IN 1/L or IN 2/R) terminal.
8 E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1/L, IN 2/R) terminals (BNC)
Input terminals for the 3G SDI/HD SDI/SD SDI signals.
● The terminals accept also EMBEDDED AUDIO signals including
up to 12 audio channels with a sampling frequency of 48 kHz.
● Use SDI IN 1/L and SDI IN 2/R terminal when selecting
DUAL LINK SDI for the input.
● In the stereo camera rig shooting, the L image is input into the SDI IN
4 REMOTE terminal
Terminal for controlling the monitor by an external control
(→ “External Control” on page 26).
5 DVI-D (HDCP) terminals
Input terminal for the DVI-D signal compatible with HDCP.
● When the picture is not displayed correctly, change the
setting of “DVI INPUT SEL.” (→ page 25)
1/L terminal, and the R image into the SDI IN 2/R terminal. In the case
of 3G SDI LEVEL B, the image is input into the SDI IN 1/L terminal.
For 3G SDI LEVEL B Dual Stream, input into the SDI IN 1/L
terminal. For 3G SDI LEVEL B DUAL LINK mapping, input into
the SDI IN 1/L and SDI IN 2/R terminals.
9 E.AUDIO 3G SDI/HD SDI/SD SDI (ACTIVE OUT) terminal (BNC)
Output terminal for the 3G SDI/HD SDI/SD SDI signals.
● The SDI IN 1/L and SDI IN 2/R input signals are reclocked and output.
● The signals are emitted from this terminal only when
the monitor is on or in “P.SAVE” (power save) mode.
Attaching the power cord holder
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. The holder consists of two parts: the cord case and the case cover.
case cover
AC IN terminal
cord case
1
2
3
To take off the case cover
● Do not use any screws other than those supplied.
● Push the case cover into the cord case and check that the power plug is connected firmly.
7
DT3D24G1_EN.indb 7
11.1.25 0:53:45 PM
Daily Operations
Front panel
Tally lamp
This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.
• You can select the color of the tally lamp from “GREEN” or “RED.”
(→ “TALLY SELECT” in “FUNCTION SETTING” on page 23 and “External Control” on page 26)
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even
when the function does not actually work).
• You cannot use the buttons for the items controlled by the MAKE system (“REMOTE ON” appears, and the lamp does not light up).
1 Speakers (stereo)
The speakers emit the same audio signal emitted from the
AUDIO MONITOR OUT terminals.
(→ 7 “AUDIO MONITOR OUT(OUT (L), OUT (R)) terminals” on
page 7)
2 VOLUME adjustment knob
Adjusts the volume.
3 Picture adjustment knob
CHROMA: Adjusts the picture color density.
BRIGHT:
Adjusts the picture brightness.
CONTRAST: Adjusts the picture contrast.
● CHROMA cannot be adjusted for certain signal
formats.
4 POSITION knob/PUSH SEL. button
POSITION knob:
Adjusts the positions of the display line
and R image.
Used for the following functions
•
•
•
•
•
•
3D cursor (→ page 16)
SPLIT (→ page 15)
LR SEQ. (→ page 15)
R SHIFT (→ page 15)
ANAGLYPH (→ page 15)
INDIVIDUAL (→ page 15)
PUSH SEL. button: Switches the display line.
Used for the following functions
• 3D cursor (→ page 16)
• SPLIT (→ page 15)
● To reset the displayed line and R image to default,
press and hold the PUSH SEL. button for 3 seconds
or longer.
8
DT3D24G1_EN.indb 8
11.1.25 0:53:45 PM
5 MUTING button
r T.C. (time code) button/lamp
Turns off the sound when no menu screen is displayed (Muting).
Activates/deactivates the display of the time data (time code)
contained in the SDI signal (→ “On the Information Display”
on page 10).
● To cancel the function, press the button again or turn
the VOLUME adjustment knob.
● Muting function is also canceled when “BALANCE” of “AUDIO
● Select the time code type in “INFORMATION” of SET-UP
SETTING” in the MAIN MENU is changed (→ page 21).
6
MENU (→ page 24).
t SELECT button
/ / / buttons
When a menu screen is displayed
Selects or adjusts menu items (→ “Menu Operations” on page 18).
When no menu screen is displayed
Selects the audio channels of EMBEDDED AUDIO signals
(→ “Audio Channel Selection” on page 10).
● Pressing
button while holding button displays the
SET-UP MENU (→ “Menu Operations” on page 18).
Selects/Changes items.
Used for the following item/function.
• 3D format (→ page 19)
• 3D cursor (→ page 16)
• INDIVIDUAL (→ page 15)
y 3D button/lamp
Activates/Deactivates the 3D mode.
7 MENU button
● Corrects images for 3D viewing with circular polarizing
Activates/deactivates the display of the MAIN MENU
(→ “Menu Operations” on page 18).
8 COLOR OFF button/lamp
glasses.
u CAMERA ASSIST button/lamp
Displays/Hides the CAMERA ASSIST MENU (→ page 14).
● Only works for images available in MIX mode.
Displays only the luminance signal.
● This function does not work for RGB input signals.
9 1:1 button/lamp
i MIX button/lamp
Activates/Deactivates the MIX mode.
● Mixes L and R images and converts to side-by-side
Displays the picture in the original resolution of the input signal.
● The aspect ratio of the picture may change depending
images (→ page 13).
o INPUT SELECT buttons/lamps
on the input signal.
p MARKER button/lamp
Selects an input.
SDI 1/L:
Input from the E. AUDIO 3G SDI/HD SDI/
SD SDI (IN 1/L) terminal
SDI 2/R:
Input from the E. AUDIO 3G SDI/HD SDI/
SD SDI (IN 2/R) terminal
DUAL LINK:
Input from the E. AUDIO 3G SDI /HD SDI/
SD SDI (IN 1/L, IN 2/R) terminals
DVI:
Input from the DVI-D (HDCP) terminal
Displays/Hides the area marker/safety marker.
● Configure the setting in “MARKER” of the MAIN MENU (→ page 20).
● Available when both the 3D and MIX modes are “OFF.”
● Not activate when picture is displayed in the 1:1 mode.
● The area marker can only be displayed in 16:9 display mode.
q 3D CURSOR button/lamp
Displays/Hides the cursor for measuring the visual difference
during 3D display (→ page 16).
● The lamp for the selected input lights.
● The SDI 1/L and SDI 2/R lamps light up in MIX mode.
● Each time you press this button, the display mode
(Only the SDI 1/L lights up in 3G SDI LEVEL B Dual
Stream input.)
changes in the following order.
No display
Cursor mode
Grid mode
; Power lamp
Off:
Green:
Orange:
The power is turned off
The monitor is on
The monitor is turned off (standby), or the
DC power voltage is reduced while working
and the monitor is shut down
Orange blinking: P.SAVE (Power saving) mode (“NO SYNC
ACTION“ in “SYNC FUNCTION“) (→ page 22)
w SCREENS CHECK button/lamp
Displays only the selected element (R, G, or B) of the video signal.
● This function does not work for RGB input signals.
● Each time you press this button, the picture changes in the following order.
RGB (Normal screen)
Red screen
Blue screen
Green screen
● You cannot turn on the monitor if the DC power is
shut down while the power lamp lights up in orange.
Disconnect the DC connector, set up the DC power
within the operating range, and then connect the
connector again.
e SCOPE button/lamp
Displays/hides the indication of the wave form monitor and
vector scope (→ “SCOPE SETTING” on page 22).
● Each time you press this button, the window changes in
the following order.
• When the MIX mode is “OFF” or invalid
No display
Wave form monitor
Vectorscope
a
button
Turns on and off (on standby) the monitor.
● The AC power switch is equipped on the rear panel of
the monitor (→ 2 on page 7).
• When the MIX mode is “ON” (→ page 16)
No display
Parallel wave form monitor
Parallel vector scope
Difference wave form monitor
Difference vector scope
9
DT3D24G1_EN.indb 9
11.1.25 0:53:46 PM
Daily Operations (cont.)
Audio Channel Selection
Select audio channels emitted from the speakers (L/R) and the AUDIO MONITOR OUT(OUT1(L)/OUT2(R)) terminals, when EMBEDDED AUDIO
signals come in to the SDI terminal and SDI input is selected.
● You have to choose a group of selectable audio channels before the channel selection (→ “E.AUDIO GROUP” in “AUDIO SETTING” on page 21).
● The setting is memorized for each input (SDI 1/L and SDI 2/R).
● Works as SDI 1/L in MIX mode and DUAL LINK SDI input.
1 Press or button when a menu is not displayed.
The screen for audio channel selection is displayed.
● The screen for audio channel selection automatically disappears in about 30 seconds after the previous operation.
Audio channel selection screen
Selected item
2 Press
3 Press
buttons to select the left (L ch) or right (R ch).
buttons to select an audio channel.
● Each time you press the button, the audio channel changes according to the settings of “E.AUDIO GROUP.” (→ page 21)
4 Press MENU button.
● The screen for audio channel selection disappears.
On the Information Display
The monitor displays the information below.
● Configure the show/hide setting of each item in the menu. Use the T.C. button (→ r on page 9) to configure 5 and 6.
● Select the position of the information display (→ “POSITION” in “INFORMATION” on page 24).
● When any information of 1 2 3 or 4 above is displayed while signals come in from equipment other than a computer, the picture is
displayed without overlapping the information display area. However, the information display will overlap with the picture when...
– Displaying the picture with higher resolution than the resolution of the panel in 1:1 mode.
– “SD4:3 LARGE” in the “FUNCTION SETTING” of SET-UP MENU is set to “ON.” (→ page 23)
1 Audio level meter
● You can check the conditions of the EMBEDDED AUDIO signals when “LEVEL METER ch” is set to “LINE” or “DIVIDE.”
● Not displayed when “LEVEL METER ch” is set to “OFF.” (→ “AUDIO SETTING” on page 21)
2 Signal format
● Displayed when “STATUS DISPLAY” is set to “ON.” (→ “INFORMATION” on page 24)
● For the contents displayed, see “Available signals” on page 33 and “On the signal format” on page 11.
3 Source name assigned in “CHARACTER SET.”
● Displayed when “SOURCE ID” is set to “ON” or “AUTO.”
● Displayed in large letters when “STATUS DISPLAY” is set to “OFF” or “AUTO.” (→ “INFORMATION” on page 24)
4 CRC error indication
● Displayed when “CRC ERROR” is set to “ON.” (→ “INFORMATION” on page 24)
● A red square is displayed when an error occurs.
5 Time code
● When the input signal includes no time code, “TC – –:– –:– –:– –” is displayed (→ r on page 9).
6 Time code (When the 3D button is “OFF” in MIX mode or the CAMERA ASSIST MENU is displayed)
TC1: For SDI IN 1/L input signals
TC2: For SDI IN 2/R input signals
DIF: Difference of TC2 from TC1
● When the CAMERA ASSIST MENU is “R SHIFT”, the time code of SDI IN 1/L input signals is displayed in the 5 position.
● It is not displayed when the CAMERA ASSIST MENU is “ANAGLYPH.”
10
DT3D24G1_EN.indb 10
11.1.25 0:53:46 PM
On the Status Display
If you press the INPUT SELECT button (→ o on page 9) currently lit, the status of the input signal and setting of MUTING are displayed for about
3 seconds.
● Make the setting to display/hide the status in “STATUS DISPLAY” of the “INFORMATION.” (→ page 24)
● When “STATUS DISPLAY” is set to “AUTO” or “ON,” the status below is also displayed in the following cases:
– When you change the input
– When the signal condition of the current input changes
– When you turn on the monitor
● When “STATUS DISPLAY” is set to “ON,” the signal format will remain displayed 3 seconds after the status is displayed.
1 Signal format
● For the contents displayed, see “Available signals” on page 33 and “On the signal format” below.
On the signal format
The following messages appear depending on the type of input signals and their conditions.
When a DVI-D signal protected with HDCP is input
➔ “*” (at the end of the indication)
When no video signal comes in
➔ “NO SYNC”
When a noncompliant video signal comes in
➔ “Out of range”
When a signal that does not meet the MIX operating conditions is input in MIX mode
➔ “Unsupported”
2 Signal format of DVI input
→ On page 25 “DVI INPUT SEL.”
Status indication of DUAL LINK/3G SDI signal information
● “DUAL LINK” appears when the MAIN MENU “SDI DUAL LINK” (→ page 19) is set to “ON” in SDI input, and the 3G SDI signal
information appears when the MAIN MENU “SDI DUAL LINK” is set to “OFF.” However in MIX mode, the 3G SDI signal
information appears even when the MAIN MENU “SDI DUAL LINK” is set to “ON.”
Status indication of 3G SDI signal information
Following signal information can be displayed when a 3G SDI signal comes in.
3G A-1:
Level A mapping structure 1
3G A-2:
Level A mapping structure 2
3G A-3:
Level A mapping structure 3
3G A-4:
Level A mapping structure 4
3G B-DS1: Level B data stream 1
3G B-DS2: Level B data stream 2
3G B-DUAL: Level B DUAL LINK
3G B-DS1/2: Level B Dual stream mapping (in MIX mode)
3D format conversion method
● The 3D format conversion method appears when the 3D mode is activated while the MIX mode is “OFF.”
(→ page 19 “SDI FORMAT”/“DVI FORMAT” in the MAIN MENU “3D SETTING.”)
● Displayed left-justified when not in 3G SDI input or DVI input.
3 Detailed information on 3G SDI/HD SDI DUAL LINK input
● Displays the sampling structure/color space/pixel resolution of the signal format.
● Displayed when the 3G SDI or HD SDI DUAL LINK signal is input.
4 Setting of “MUTING”
● Displayed only when muting is activated (→ 5 on page 9).
5 Setting of FRAME SYNC.
● Only displayed when “FRAME SYNC.” in the MAIN MENU “3D SETTING” is set to “ON.” (→ on page 19)
11
DT3D24G1_EN.indb 11
11.1.25 0:53:47 PM
Viewing 3D images
Basic 3D principle
This product is a 3D LCD Monitor which adopts the Xpol® circular polarizing method.
By having a filter of different polarization on every alternate scan line on the monitor, and projecting the left eye image (left circular polarization)
and the right eye image (right circular polarization) through the filters, users can enjoy a realistic three dimensional view by viewing the left and
right images simultaneously through the circular polarizing glasses.
As the left and right images are always displayed together on the screen, users can view flicker-free 3D images.
Compatible 3D format
The following 3D formats are supported: LINE BY LINE, SIDE BY SIDE HD, and SIDE BY SIDE SD.
LINE BY LINE
Displays image stripes
of the left and right
images line by line one
after another.
SIDE BY SIDE HD
Shrinks the size of the
left and right images
by half and displays
them side by side.
The horizontal
resolution is divided
into two.
SIDE BY SIDE SD
Tiles images for the left and
right eyes horizontally without
compressing. The horizontal
resolution remains unchanged,
but both sides of the screen are
displayed in black in 3D mode.
When viewing in 3D
● View 3D images at the recommended viewing distance (Recommended viewing distance : Approx. 65cm(25 5/8")).
● To view in 3D, change to a suitable mode before putting on the circular polarizing glasses to view the 3D images.
● Every individual will have a different experience when viewing 3D images. Viewing at a close distance may cause
disorders and discomfort.
● The 3D effects may differ when viewing the screen from different angles.
● Avoid viewing 3D images if you are in bad shape.
● Stop using the product and rest immediately if you experience eyestrain, dizziness, vomiting, headaches or any
other discomforts.
● If the symptoms persist even after resting, please consult a doctor.
● Take periodic breaks and rest even if you do not experience any discomfort. (Recommended viewing time : about 30
to 60 minutes).
● For users with past experiences of PSS (Photo Sensitive Seizure) or users with heart problems, please consult a
doctor before using this monitor.
● For children 6 and under still in the visual development stage, please consult a doctor and have an adult guardian
accompany the child.
● Though ghosting may occur when viewing 3D images, this is not due to a malfunction but to a characteristic of the
LCD panel.
Cautions on using the circular polarizing glasses
● Use the circular polarizing glasses only when viewing 3D images.
● Use the circular polarizing glasses provided or compatible with RealD™.
● For users who wear spectacles, cover the spectacles with the circular polarizing glasses.
● Do not use the circular polarizing glasses as sunglasses.
● Please consult a doctor if allergies appear on the areas that come into contact with the circular polarizing glasses.
NOTE
● When purchasing additional circular polarizing glasses, please select RealD™-compatible ones or contact the dealer where
you purchased your monitor.
● Though some faint black lines may appear on the screen when viewing 2D images, this is not due to a malfunction but to a
characteristic of the LCD panel.
• Xpol® is a registered trademark of Arisawa Manufacturing Co., Ltd.
• RealD™ is a trademark of RealD Inc. (US)
12
DT3D24G1_EN.indb 12
11.1.25 0:53:47 PM
To view 3D images
To view in 3D, enter the 3D mode. The procedures differ between viewing existing 3D images and mixing L and R images taken by two cameras.
To view existing 3D images
View already 3D-processed images.
1 Input existing 3D images into the SDI IN 1/L, 2/R terminals or DVI-D terminal.
➔ Also compatible with DUAL LINK.
2 Press the INPUT SELECT button corresponding to the input images.
3 Press the 3D button.
4 Press the SELECT button to select a 3D format.
➔ Select a 3D format configured under “SDI FORMAT 1”/”SDI FORMAT 2” or “DVI FORMAT 1”/”DVI FORMAT 2” in the MAIN MENU
“3D SETTING.”
● Put on the circular polarizing glasses to view in 3D. Press the 3D button to enter the 3D mode that corrects
images for viewing with the circular polarizing glasses.
● 3D viewing is not available if the 3D images are not based on LINE BY LINE or SIDE BY SIDE.
● If the SIDE BY SIDE images in DVI input do not seem to be in the right position, adjust the image position under
“3D H POSITION” in the SET-UP MENU “H POSITION ADJ.” beforehand.
● If necessary, configure the settings such as the MAIN MENU “3D SETTING.”
● When inputting LINE BY LINE 3D images in a signal format that scales the screen vertically, use the 1:1 display
mode.
To view images taken by two cameras
Mix L and R images taken by two cameras and convert them to 3D images.
1 Input L images into the SDI IN 1/L terminal and R images into the SDI IN 2/R terminal.
➔ Input L and R images in the same format corresponding to the MIX mode.
(For 3G SDI LEVEL B Dual Stream, input into the SDI IN 1/L terminal. For 3G SDI LEVEL B DUAL LINK mapping, input into the SDI
IN 1/L and SDI IN 2/R terminals.)
2 Press SDI 1/L or SDI 2/R (INPUT SELECT button).
➔ In the case of 3G SDI LEVEL B Dual stream, press SDI 1/L.
3 Press the MIX button.
➔ Images in SIDE BY SIDE format.
4 Press the 3D button.
● Put on the circular polarizing glasses to view in 3D. Press the 3D button to enter the 3D mode that corrects
images for viewing with the circular polarizing glasses.
● If necessary, configure the settings such as the MAIN MENU “3D SETTING” or CAMERA ASSIST MENU.
13
DT3D24G1_EN.indb 13
11.1.25 0:53:48 PM
Setting the CAMERA ASSIST MENU
This product is equipped with various camera rig adjustment assist functions for 3D viewing. Use the functions for camera adjustment in
shooting.
CAMERA ASSIST MENU
Menu Operations
1 Press the CAMERA ASSIST button.
➔ The CAMERA ASSIST MENU appears.
● Only works when the SDI input is selected and images available for the
MIX mode are input.
● When the CAMERA ASSIST button is pressed while “MARKER” is
displayed, “MARKER” disappears and the CAMERA ASSIST MENU appears.
2 Press the
button to select an item,
and then the button to proceed to the next screen.
● For some items, adjustments will be made by pressing
.
3 Press the CAMERA ASSIST button to finish the menu operation.
● Alternetively, press the MENU button to close the menu screen.
CAMERA ASSIST MENU
RIG SETTING
Depending on the stereo camera rig condition, configure the horizontal flip/vertical flip/180-degree rotation settings of an image.
● The settings are retained even when the CAMERA ASSIST MENU closes.
Half mirror
Half mirror
Parallel twin-flex
Half of the image is flipped horizontally.
● Select “R-H-MIRROR.”
Half of the image is flipped vertically.
● Select “R-V-MIRROR.”
Half of the image is rotated 180 degrees.
● Select “R-ROTATION.”
Setting value
Content
OFF
Does not rotate or flip the image
R-H-MIRROR
Horizontally flips images input into the SDI IN 2/R terminal
R-V-MIRROR *1
Vertically flips images input into the SDI IN 2/R terminal
L-H-MIRROR
Horizontally flips images input into the SDI IN 1/L terminal
L-V-MIRROR *1
Vertically flips images input into the SDI IN 1/L terminal
R-ROTATION *1
Rotates images input into the SDI IN 2/R terminal by 180 degrees
L-ROTATION *1
Rotates images input into the SDI IN 1/L terminal by 180 degrees
*1
Vertical flip and 180-degree rotation delay the image by 2 frames. The other image will also be delayed and synchronized.
14
DT3D24G1_EN.indb 14
11.1.25 0:53:49 PM
L image
SPLIT
L image is displayed on the left of the SPLIT line, and R image on
the right. You can check the difference between the images from
the two cameras.
R image
L
H line
SPLIT line
LR SEQ.
Images for the left and right eyes are displayed alternately at
0.5-second interval.
● A marker appears on the upper part of the screen, which
distinguishes between L and R images.
L image: Upper left
R image: Upper right
L image
R image
L R L R
0.5 sec.
0.5 sec. 0.5 sec.
H line
0.5 sec.
R SHIFT
L and R images are overlapped. You can move the R image
horizontally and check the difference between the images.
● While “R SHIFT” is active, the images are corrected according to
the check using the circular polarizing glasses.
L and R images not correspondent
L and R images correspondent
ANAGLYPH
L and R images colored red and blue separately are overlapped.
You can move the R image horizontally and check the difference
between the images.
INDIVIDUAL
Either L image or R image is displayed.
● Each time you press SELECT button, the picture changes in the
following order.
● A marker appears on the upper part of the screen, which
distinguishes between L and R images.
L image: Upper left
R image: Upper right
LR SWAP
L and R images are exchanged and then displayed. You can
exchange the images without repluging the terminals.
● The setting is retained even when the menu closes. Note that L
and R images have been exchanged when the setting is set to
“ON.”
L image
SDI IN
SDI IN
1/L 2/R
LR SWAP “OFF”
R image
SDI IN
SDI IN
2/R
1/L
LR SWAP “ON”
POSITION knob/PUSH SEL. button
You can move the displayed SPLIT line/H line/R image (only in “R SHIFT” or “ANAGLYPH”) by turning
the POSITION knob.
To move right/up: Turn the POSITION knob clockwise.
To move left/down: Turn the POSITION knob counterclockwise.
To select a line to move: Press the PUSH SEL. button.
● Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the lines and R image to the default positions.
● The intensities of the SPLIT and H lines can be changed in “L. INTENSITY” under the MAIN MENU “3D SETTING.” (→page 19)
15
DT3D24G1_EN.indb 15
11.1.25 0:53:50 PM
Other 3D functions
SCOPE button/lamp
You can display the wave form monitor or vector scope, and compare and check the SDI IN 1/L and SDI IN 2/R input signals.
● Works in MIX mode. The operation to be performed differs in other modes. (→ page 9)
● Each time you press the SCOPE button, the display mode changes in the following order.
No display
Parallel wave form
monitor
: Does not display the wave form monitor/vector scope.
: Tiles the wave form monitors of the images input into the SDI IN 1/L and SDI IN 2/R terminals.
Parallel vector scope :
Difference wave form :
monitor
:
Difference vector
scope
Y
Tiles the vector scopes of the images input into the SDI IN 1/L and SDI IN 2/R terminals.
Select this to display the differential of the signals from the SDI IN 1/L and SDI IN 2/R terminals in
wave form monitor.
Select this to display the differential of the signals from the SDI IN 1/L and SDI IN 2/R terminals in
vector scope.
Y
Parallel wave form monitor
Y
Parallel vector scope
Difference wave form monitor
Difference vector scope
• When the CAMERA ASSIST MENU “LR SWAP” is set to “ON”, L and R images of the parallel wave form monitor and vector scope are
exchanged and then displayed.
• The positions of the wave form monitor and vector scope can be changed in “POSITION” under the MAIN MENU “SCOPE SETTING.”
• The wave form monitor and vector scope are not displayed in “R SHIFT” or “ANAGLYPH” of the CAMERA ASSIST MENU.
• The vector scope is not displayed when the input signals are RGB.
3D CURSOR button/lamp
When 3D is “ON”, the L and R lines measuring the visual difference between L and R images, and the pixels and percentage between the
lines, are displayed. The following two modes are available for the line display: “Cursor mode” and “Grid mode.”
● Each time you press the 3D CURSOR button, the line display mode changes in the following order.
No display
Cursor mode
Grid mode
● The information (→ page 10) and SCOPE are not displayed in “Cursor mode” or “Grid mode.”
● The positions of the pixels and percentage can be changed in “POSITION” under the MAIN MENU “INFORMATION.”
Cursor mode
The L, R, and H lines appear, which measure the visual difference.
● The H and L lines are fined dotted lines, and the R line a coarse dotted line. The selected line is displayed as a solid line.
L line (Group A)
R line (Group A)
Pixels/Percentage between L and R lines
-
H line (Group B)
H line (Group A)
(selected line)
R line (Group B)
L line (Group B)
● The line color changes when the line goes beyond “FAR LIMIT” or “NEAR LIMIT” under the MAIN MENU “3D SETTING.”
● The ratio of the difference between the L and R lines to the horizontal pixels appears in the percentage display.
● In the percentage display, “+” indicates the pop-up level (when the L line is placed on the right of the R line), and “–” the depth
16
DT3D24G1_EN.indb 16
(when the L line is placed on the left of the R line).
11.1.25 0:53:50 PM
● In Cursor mode, the lines of the following two groups are displayed:
Group A: L line/R line/H line (Normal: Green
/ Over the LIMIT: Red)
Group B: L line/R line/H line (Normal: Magenta / Over the LIMIT: Orange)
• You can change a group to display by pressing the SELECT button. Each time you press the SELECT button,
the group changes as shown on the right.
• The line color turns to a color to be used when the LIMIT is exceeded when it goes beyond “FAR LIMIT” or
“NEAR LIMIT” under the MAIN MENU “3D SETTING.”
● You can move the L, R, and H lines by turning the POSITION knob.
To move right/up:
Turn the POSITION knob clockwise.
To move left/down:
Turn the POSITION knob counterclockwise.
To select a line to move: Press the PUSH SEL. button. Each time you press the button, the selected line changes in the following order.
L line
R line
H line
L+R line
• When you select a line while both Group A and B are displayed, the selection is performed for Group A first, and then for Group B.
• When both L and R lines are selected, the lines cannot be moved separately.
• Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the displayed lines to the default positions.
Grid mode
The grid lines appear, which measure the visual difference.
Pixels/Percentage between the grid lines
Center window
● The following two types of the grid mode display are available: Normal display and Center window display.
You can change the display by pressing the SELECT button.
Normal display
Center window display
● The width of the grid line can be changed. Turning the POSITION knob enlarges/reduces the width based on the upper left of the screen as
the datum point.
To enlarge: Turn the POSITION knob clockwise.
To reduce: Turn the POSITION knob counterclockwise.
Reduce the width
Enlarge the width
● The ratio of the difference between the grid lines to the horizontal pixels appears in the percentage display.
● Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the grid width to 100 pixels (default).
● When “L. INTENSITY” under the MAIN MENU “3D SETTING” is set to “LOW”, the grid line is displayed translucent.
17
DT3D24G1_EN.indb 17
11.1.25 0:53:51 PM
Setting the menu (MAIN MENU/SET-UP MENU)
Menu Operations
1
MAIN MENU
Item being
selected
Display the menu.
To display the MAIN MENU
➔ Press MENU button.
To display the SET-UP MENU
➔ Press button while holding
2
Press
Operation
guide
button.
buttons to select an item, then press button.
● For some items, adjustments will be made by pressing
3
4
Press
SET-UP MENU
buttons to select an item, then press
.
buttons to make adjustments.
MAIN MENU
Ex. When “MARKER” is
selected.
Press MENU button to finish the menu operation.
● Pressing MENU button repeatedly deactivates the display of the menu.
Menu Transition Diagram
MAIN MENU
PICTURE FUNCTION
BACK LIGHT
3G SDI LEVEL B
APERTURE
APERTURE LEVEL
I/P MODE
sub menu
reset
SDI DUAL LINK
3D SETTING
ASPECT
MARKER
AUDIO SETTING
SCOPE SETTING
BALANCE
E.AUDIO GROUP
LEVEL METER SETTING
SYNC FUNCTION
NO SYNC ACTION
DELAY TIME
LOW LATENCY
SDI FORMAT 1
SDI FORMAT 2
DVI FORMAT 1
DVI FORMAT 2
SINGLE IMAGE
FRAME SYNC.
FAR LIMIT
NEAR LIMIT
L. INTENSITY
LEVEL METER ch
BAR TYPE
REFERENCE LEVEL
OVER LEVEL
BAR BRIGHTNESS
PEAK HOLD
GAIN
SIZE
POSITION
TRANSPARENT
AUTO OFF
WAVE DISPLAY
WAVE FILTER
WAVE OVER LEVEL
AREA MARKER
MARKER ASPECT
SAFETY MARKER
SAFETY AREA
FRAME
CENTER MARKER
LINE BRIGHTNESS
R-AREA MARKER
R-MARKER ASPECT
R-SAFETY MARKER
R-SAFETY AREA
MARKING
LEVEL
SET-UP MENU
FUNCTION SETTING
PICTURE SUB ADJ.
H POSITION ADJ.
WHITE BALANCE SET.
3D H POSITION
sub menu
reset
REMOTE SETTING
INFORMATION
CONTROL LOCK
DVI INPUT SEL.
SDI FORMAT
all reset
POSITION
SOURCE ID
CHARACTER SET.
STATUS DISPLAY
TIME CODE
CRC ERROR
SUB HOUR METER
MODEL
VERSION
HOUR METER
CONTRAST
BRIGHT
CHROMA
sub menu
reset
SERIAL TYPE
PARALLEL TYPE
PIN1
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
sub menu POSI.
TALLY SELECT
SD4:3 LARGE
DIMMER
GAMMA
COLOR TEMP.
R DRIVE
G DRIVE
B DRIVE
R CUT OFF
G CUT OFF
B CUT OFF
sub menu
reset
● The menu automatically disappears in about 30 seconds after the previous operation.
● Some items may not appear on the menu depending on the input or the input signal.
● The items controlled by the MAKE system do not appear on the menu.
18
DT3D24G1_EN.indb 18
11.1.25 0:53:51 PM
MAIN MENU
PICTURE FUNCTION
Setting for the picture quality.
Item
Content
APERTURE *1
Activates/deactivates the function at the level set in “APERTURE LEVEL.”
OFF, ON
APERTURE LEVEL *1
I/P MODE
Simultaneously corrects the frequency characteristics of the RGB colors.
01 – 10
Selects a proper mode corresponding to the input picture.
NORMAL, CINEMA, FIELD
sub menu
reset
Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION” while viewing the actual picture.
*1
Setting value
Restore the default settings for all the items in “PICTURE FUNCTION.”
Memorized for each input.
BACK LIGHT
Setting value: -20 – +20
Adjusts the brightness of the display.
3G SDI LEVEL B
Setting value: DS1, DS2
Selects the data stream from two HD SDI signals multiplexed when a 3G SDI LEVEL B signal comes in.
● The setting value will be invalid if a 3G SDI LEVEL B DUAL LINK signal is input.
SDI DUAL LINK
Setting value: OFF, ON
Activates/deactivates the DUAL LINK function of SDI signals.
● “DUAL LINK” is displayed when the setting is set to “ON.” (→ “Status indication of DUAL LINK/3G SDI signal information” on page 11)
● Set this setting to “OFF” when an SDI signal other than DUAL LINK SDI is input.
3D SETTING
3D function settings.
Item
Content
Setting value
SDI FORMAT 1 *1
Set the first choice for 3D format in SDI input.
The setting values and features are as follows.
LbL-RL
LbL-LR
SbS-HD-LR
SbS-HD-RL
SbS-SD-LR
SbS-SD-RL
LbL-RL
LbL-LR
SbS-HD-LR
SbS-HD-RL
SbS-SD-LR
SbS-SD-RL
:
:
:
:
:
:
LINE BY LINE, the first line: R image
LINE BY LINE, the first line: L image
SIDE BY SIDE compressed horizontally, L image on the left
SIDE BY SIDE compressed horizontally, R image on the left
SIDE BY SIDE not compressed, L image on the left
SIDE BY SIDE not compressed, R image on the left
• When the 3D mode is “ON” in 3D input, pressing the SELECT button switches between
“FORMAT1” and “FORMAT2.”
SDI FORMAT 2 *1
DVI FORMAT 1 *1
DVI FORMAT 2 *1
Set the second choice for 3D format in SDI input.
Set the first choice for 3D format in DVI input.
Set the second choice for 3D format in DVI input.
SINGLE IMAGE *1
Select a channel to be displayed when the 3D mode is “ON.”
OFF
:
LEFT
:
RIGHT :
FRAME SYNC.
Normal 3D (Left and right images)
L image only
R image only
OFF
LEFT
RIGHT
Synchronize the left and right input signals by forcibly locking the SDI IN 2/R input for the SDI IN 1/L OFF
input in MIX mode.
ON
• The time base cannot be corrected on this product. To take 3D images strictly, perform
GENLOCK on the shooting device, and set this setting to “OFF.”
• When “ON” is selected, the playback proceeds one frame later than when “OFF” is selected.
FAR LIMIT
Set the limit of the depth in Cursor mode of “3D cursor.”
– 0.1% – – 4.0%
• The line color changes when the difference between the vertical lines goes beyond the
specified range.
NEAR LIMIT
Set the limit of the pop-up level in Cursor mode of “3D cursor.”
L. INTENSITY
• The line color changes when the difference between the vertical lines goes beyond the
specified range.
Set the intensity of lines displayed in the CAMERA ASSIST MENU and “3D cursor.”
• When “LOW” is selected, the grid lines are displayed translucent in Grid mode of “3D
cursor.”
*1
+01% – +20%
HIGH
LOW
Works when the MIX mode is “OFF” or invalid.
19
DT3D24G1_EN.indb 19
11.1.25 0:53:52 PM
Menu Configuration (cont.)
ASPECT
Setting value: 4:3, 16:9
Set the aspect ratio of images.
● Not activate when picture is displayed in the 1:1 mode.
MARKER*1*2
Settings for marker functions.
1/2
Item
Content
Setting value
AREA MARKER *3
Activate/deactivate the area marker and select the style of it.
The setting values and features are as follows.
OFF
LINE
HALF
HALF+L
BLK.
BLK.+L
OFF
LINE
HALF
: Deactivate the marker.
: Displays the area with an outline.
: The area outside the specified aspect ratio of the screen is
displayed at 50% transparency.
HALF+L : The area of the specified aspect ratio of the screen is
indicated by an outline, and the area outside of that is
displayed at 50% transparency.
BLK.
: The area outside the specified aspect ratio of the screen is
black. Only the portion of the picture within the designated
area is displayed.
BLK.+L : The area of the specified aspect ratio of the screen is
indicated by an outline, and the area outside of that becomes
black so that only the area inside the line is displayed.
2/2
MARKER ASPECT *3
Select the aspect ratio of the area marker.
4:3, 14:9, 13:9, 2.35:1,
1.85:1, 1.66:1
SAFETY MARKER
Activate/deactivate the safety marker and select the style of it. *4
OFF, LINE, HALF, HALF+L,
BLK., BLK.+L
SAFETY AREA
FRAME
CENTER MARKER
Adjust the area of the safety marker.
80% – 100%
Displays/hides the frame indicating the area of the specified aspect ratio.
OFF, ON
Displays/hides the marker indicating the center position of the picture.
OFF, ON
LINE BRIGHTNESS
R-AREA MARKER *3
Adjust the brightness of the marker.
HIGH, LOW
Display/Hide the area marker and select a type. *4
OFF, LINE, HALF,
HALF+L,
BLK., BLK.+L
R-MARKER ASPECT *3
Select the aspect ratio of the area marker.
4:3, 14:9, 13:9, 2.35:1,
1.85:1, 1.66:1
R-SAFETY MARKER
Activate/deactivate the safety marker and select the style of it. *4
OFF, LINE, HALF,
HALF+L,
BLK., BLK.+L
R-SAFETY AREA
Adjust the area of the safety marker.
80% – 100%
● The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or external control.
● Select either non-“R-” items or “R-” items to activate by using external control (→ “External control” on page 26).
● When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.
● To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.
*1
*2
Memorized for each input.
Not displayed in 1:1 mode or when “SD4:3 LARGE” under the SET-UP MENU “FUNCTION SETTING” is set to “ON” and 4:3 format signals
are input.
*3 Displayed only when picture is displayed in 16:9 aspect ratio.
*4 The setting values are the same as that of “AREA MARKER.”
20
DT3D24G1_EN.indb 20
11.1.25 0:53:53 PM
AUDIO SETTING
Settings for the audio output balance, EMBEDDED AUDIO signals and level meter.
Item
Content
Setting value
BALANCE
E.AUDIO GROUP *1
Adjust the balance between the right and left speakers.
L5 – L1, 0, R1 – R5
Select the audio channel group of the EMBEDDED AUDIO signals.
The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.
1G
2G
1-2G
3G
1-3G
1G
2G
1-2G
3G
1-3G
:
:
:
:
:
Channel 1/2/3/4/1+2/3+4/1 – 4 (1G)
Channel 5/6/7/8/5+6/7+8/5 – 8 (2G)
Channel 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)
Channel 9/10/11/12/9+10/11+12/9 – 12 (3G)
Channel 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/
1 – 4 (1G)/5 – 8 (2G)/9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)
• G means GROUP
LEVEL METER SETTING *1
Adjust the level meter display for the EMBEDDED AUDIO signals.
Example of the level meter display —Level meter position and audio channels
Ex.: When “LEVEL METER ch” is set to “LINE” and “BAR TYPE” is set to “3COLORS”
OVER LEVEL
Red
Yellow
REFERENCE LEVEL
Green
• The level meter with no audio signal input is displayed in white for “3COLORS”, and in gray for “W.100.”
• You can select the position of the level meter display—top or bottom of the screen (→ “POSITION” in
“INFORMATION” on page 24).
• When “PEAK HOLD” is set to “ON,” the maximum level meter value will remain displayed for a set period
of time.
– LEVEL METER ch
Select how the audio channels are displayed on the level meter.
LINE
DIVIDE
: Displays the channels 1 – 6 at the left of the screen and 7 – 12 at the right.
: Displays the odd channels at the left of the screen and the even channels at
OFF
LINE
DIVIDE
the right.
– BAR TYPE
Select the color of the level meter display.
3COLORS : Coloring for each level
W.100
: White
3COLORS
W.100
– REFERENCE LEVEL
– OVER LEVEL
Select the standard input level indicated on the level meter.
−20dB, −18dB
Select the input level’s lower limit indicated in red for the “3COLORS” display.
−10dB, −8dB,
−6dB, −4dB, −2dB
– BAR BRIGHTNESS
– PEAK HOLD
Select the brightness of the level meter.
LOW, HIGH
Activates/deactivates the peak hold function of the level meter.
OFF, ON
*1
Memorized for each input. In MIX mode, the setting only applies to audio signals input into SDI IN 1/L.
21
DT3D24G1_EN.indb 21
11.1.25 0:53:53 PM
Menu Configuration (cont.)
SCOPE SETTING*1
Configure the settings for the wave form monitor and vector scope.
Item
GAIN
SIZE *2 *3
POSITION *2
Content
Adjust the input gain level.
Set the window size.
Select the window position.
TRANSPARENT *3
Make the background of the window translucent.
AUTO OFF
WAVE DISPLAY
ON : Translucent
OFF : Normal
Set the function to turn off the window automatically 15 minutes after displayed.
Select a wave form to be displayed for the wave form monitor.
WAVE FILTER
Turn on/off the lowpass filter to put over the input wave form data.
WAVE OVER LEVEL *3
Set the over levels of the luminance signals (Y) and RGB signals.
Setting value
–10 – +10
NORMAL, LARGE
1 (Lower right), 2 (Lower left)
3 (Upper left), 4 (Upper right)
ON
OFF
ON, OFF
Y, Pb, Pr (HD signal)
Y, Cb, Cr (SD signal)
R, G, B (RGB signal)
FLAT (No filter)
LOWPASS
Example of the wave form monitor
Example of the vector scope
Ex.: When the luminance signal is Y, “MARKING” is set to “ON” and “LEVEL” is set to
“080”
Ex.: When the color bar is
displayed
Red
White
Y
Image signals
Start
End
• The wave form color of signals over the value specified in “LEVEL” turns red.
• The display differs depending on the input signal or the “WAVE DISPLAY”
setting.
– MARKING
– LEVEL
*1
*2
*3
Turn on/off the function to change the wave form color of signals over the value
specified in “LEVEL.” (→ below)
Adjust the lower limit for the over level.
OFF, ON
070 – 109
The wave form monitor is not displayed when the input signals are DVI (input from a computer). The vector scope is not displayed when the
input signals are RGB.
When “SIZE” is set to “LARGE,” the window is displayed in the center of the screen regardless of the “POSITION” setting.
Not displayed in MIX mode or when the CAMERA ASSIST button is “ON.”
SYNC FUNCTION
Settings for the synchronization with signals.
Item
NO SYNC ACTION
DELAY TIME
LOW LATENCY
Content
Select the screen status when no signal is coming in.
STANDBY : The monitor is off (on standby)
P.SAVE
: Power save mode
GRAY B. : Gray screen
Select the period until the screen status changes as selected in “NO SYNC ACTION” after
signals stop coming in.
Activates/deactivates the function to shorten the time taken to display the picture.
Setting value
OFF
STANDBY
P.SAVE
GRAY B.
30sec., 5min., 15min.
ON
OFF
• If the picture is not displayed steadily while “ON” is selected, select “OFF.”
• While “ON” is selected, the displayed picture may become unstable when an
operation using buttons on the front panel or the menu is performed, or when the
signal format changes.
● When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption of the back light is saved by
half. Selecting “P.SAVE” (power save mode) saves more power consumption by turning off the back light.
● In the initial setting, “NO SYNC ACTION” is set to “P.SAVE”, and “DELAY TIME” set to “15min.” Change the settings if necessary. (U.S.A. only)
22
DT3D24G1_EN.indb 22
11.1.25 0:53:53 PM
SET-UP MENU
FUNCTION SETTING
Configure the sub menu display, the lighting color of the tally lamp, the size of images, the brightness of the button lamps.
Item
sub menu POSI.
Content
Select the contents and displaying position of “sub menu.”
The setting values and features are as follows.
LOWER1 : Displays the current setting and adjustment bar at the lower part of the screen.
UPPER1 : Displays the current setting and adjustment bar at the upper part of the screen.
LOWER2 : Displays the current setting at the lower part of the screen.
UPPER2 : Displays the current setting at the upper part of the screen.
Setting value
LOWER1
UPPER1
LOWER2
UPPER2
• The adjustment bar is not displayed for some items.
TALLY SELECT
SD4:3 LARGE
DIMMER
Select the color of the tally lamp.
Selects the picture size when the input signal format is 4:3.
The setting values and features are as follows.
Matches the vertical picture size to the number of pixels.
OFF
:
Matches the horizontal picture size to the horizontal size of the screen.
ON
:
Select the intensity of the button lamps.
GREEN, RED
OFF
ON
NORMAL, DARK
PICTURE SUB ADJ.
Configure the standard level of image adjustment.
Item
CONTRAST *1
BRIGHT *1
CHROMA *1
sub menu
reset
*1
Content
Setting value
Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front panel.
– 20 – +20
Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front panel.
– 20 – +20
Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel.
– 20 – +20
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing the actual picture.
Restore the default settings for all the items in “PICTURE SUB ADJ.” (You cannot select items to reset.)
Memorized for each input.
H POSITION ADJ.
Adjust the center position of SIDE BY SIDE images.
Item
Content
3D H POSITION
Display the center line to adjust the horizontal image position.
Setting value
• The setting will be valid when the 3D mode is “ON” and MIX mode is “OFF” or invalid.
sub menu
reset
– 032 – +031
Display the sub menu which enables you to adjust the items in “H POSITION ADJ.” while viewing the actual picture.
Restore the default settings for all the items in “H POSITION ADJ.”
WHITE BALANCE SET.
Selects the gamma correction value, color temperature and adjusts the drive level and cutoff point of each color (R/G/B).
Item
GAMMA
Content
Select a gamma correction.
COLOR TEMP.
Select the color temperature.
Setting value
2.2 (equivalent to γ2.2), 2.35 (equivalent to γ2.35)
2.45 (equivalent to γ2.45), 2.6 (equivalent to γ2.6)
9300K, 6500K, USER
• The color temperature is corrected when the 3D mode is “ON.”
R DRIVE
G DRIVE
B DRIVE *1
R CUT OFF
G CUT OFF
B CUT OFF *1
sub menu
reset
*1
Adjust the drive level of each color (red, green, and blue).
MIN – 000 – MAX (in 256 grades)
Adjust the cutoff point of each color (red, green, and blue).
MIN – 000 – MAX (in 256 grades)
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while viewing the actual picture.
Restore the default settings for the drive levels and cutoff points of the selected color temperature. (You cannot select
items to reset.)
Memorized for each color temperature.
23
DT3D24G1_EN.indb 23
11.1.25 0:53:54 PM
Menu Configuration (cont.)
REMOTE SETTING
(→ “External Control” on pages 26)
Settings for the external control.
Item
Content
Setting value
SERIAL TYPE
Select the input terminal used for external control by serial
communication.
RS232C
RS485
PARALLEL TYPE
PIN1
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
Select the external control method for the MAKE/TRIGGER terminal.
MAKE, TRIGGER, SET
Assign the control functions to the pins of the MAKE/TRIGGER terminal.
• Assign a function to each pin terminal by selecting “SET” in
“PARALLEL TYPE” mentioned above.
→ <Functions controlled by the
MAKE/TRIGGER system> on page
27.
The functions are assigned for “PIN6” – “PIN8” and you cannot change the
assignment of these functions.
→ “Using the MAKE/TRIGGER
system” on page 26
INFORMATION
Settings for the information display of the monitor.
Item
Content
Setting value
POSITION
Select the position to show the information display (→ “On the
Information Display” on page 10).
UPPER
LOWER
SOURCE ID
Select whether the name assigned in “CHARACTER SET.” is displayed on
the screen (→ “On the Information Display” on page 10).
OFF
ON
AUTO
• When “AUTO” is selected, the display color synchronizes with the
color of the tally lamp while the tally lamp is lit.
CHARACTER SET. *1
Assign a name to each video source as you like (10 characters at maximum).
You can also enter a name using the RS-232C system.
Setting of “CHARACTER SET.”
1 Change the input to one that you want to assign a video source name
for.
2 Select “CHARACTER SET.”
3 Press the buttons to select a character to enter at first.
● Each time you press the button, the characters change in the
following order. Press button to reverse the order.
space
4
5
6
Press button to move the arrow to the next space.
● The characters entered before moving the arrow are memorized.
Repeat steps 3 and 4 (10 characters at maximum).
Press MENU button to store the name.
STATUS DISPLAY
Select whether the status of the current input and the setting of MUTING
are displayed on the screen (→ “On the Status Display” on page 11).
AUTO, OFF, ON
TIME CODE
CRC ERROR
Select the type of the TIME CODE display.
VITC *2, LTC *2, D-VITC
Select whether the CRC error indication for the input HD SDI signal is
displayed on the screen (→ “On the Information Display” on page 10).
OFF
ON
SUB HOUR METER
Display the hours of use (unit: hour).
You can reset this item.
MODEL
VERSION
HOUR METER
Display the model name of the monitor.
*1
*2
Display the version of the monitor.
Display the total hours of use (unit: hour).
This item is used for maintenance of the monitor. You cannot reset this item.
Memorized for each input.
Ancillary time code
24
DT3D24G1_EN.indb 24
11.1.25 0:53:54 PM
CONTROL LOCK
Setting value: OFF, VOL.LOCK, ALL LOCK
Settings for disabling the buttons on the front panel.
● The following operations are not available when “VOL.LOCK” is selected.
– VOLUME adjustment knob
– Picture adjustment knob
● The “ALL LOCK” function disables to control the buttons on the front panel. But following operations are available.
– Turning on/off (on standby) the monitor.
– Press the button and button to display the SET-UP MENU, and set “CONTROL LOCK” to “OFF.”
– Operate this product by external control.
When you perform operations other than the above, “ Control lock on!” appears.
DVI INPUT SEL.
Setting value: AUTO, COMPO., RGB, PC
Settings for formats of signals input into the DVI-D (HDCP) terminal.
● Automatically distinguishes signals when set to “AUTO.” (Normally, select “AUTO”)
● Select “COMPO.”, “RGB” or “PC” when the picture is not displayed correctly with “AUTO.”
● DVI-D input of the monitor is compatible with HDCP.
SDI FORMAT
Setting value: AUTO, MS1YCbCr, MS2YCbCr,
MS3YCbCr, MS4YCbCr, MS2 RGB, MS3 RGB, 3G-B-DS
Settings for formats of signals for 3G SDI/HD SDI DUAL LINK input.
● Automatically distinguishes signals when set to “AUTO.” (Normally, select “AUTO”)
● If the picture is unstable with “AUTO”, select the setting value according to the input signal format.
● When “AUTO” is not selected, “M” appears in the status display.
all reset
Restores all the settings and adjustments of the monitor to the default.
● “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.
● If reset while the AC power is on, the monitor turns off (standby), and then turns on automatically.
● If reset while the DC power is on, the monitor turns off (standby).
25
DT3D24G1_EN.indb 25
11.1.25 0:53:55 PM
External control
About the external control
This monitor has three external control terminals.
● MAKE/TRIGGER terminal (RJ-45): The following external control
systems are available.
1 MAKE (make contact) system:
Controls the monitor by short-circuiting the corresponding pin
terminal to the GND pin terminal, or disconnecting (opening) it.
2 TRIGGER (trigger) system:
Controls the monitor by sending the pulse signal
instantaneously to the corresponding pin terminal.
→ “Using the MAKE/TRIGGER system” on the right.
● RS-485 terminal (RJ-45): Controls the monitor with the RS-485
system (→ “Using the serial communication” on page 28).
● RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS232C system (→ “Using the serial communication” on page 28).
Set the following items of “REMOTE SETTING” in SET-UP MENU
according to the external control terminal and control system (→
“SERIAL TYPE,” “PARALLEL TYPE” on page 24).
Control
terminal
MAKE/
TRIGGER
terminal
RS-485
terminal
RS-232C
terminal
Control system
The settings of this unit
“SERIAL “PARALLEL
TYPE”
TYPE”
setting
setting
MAKE
—
MAKE
TRIGGER
—
TRIGGER
RS-485
RS485 *1
—
RS-232C
RS232C *1
—
The MAKE/TRIGGER terminal is configured as follows.
You can assign a function to each pin terminal in “REMOTE SETTING.”
(→ “PIN1, PIN2, PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 24)
● You cannot change the functions assigned to the pin terminals
from 6th to 8th.
This is a female
terminal.
*1
*2
Pin No.
1
2
3
4
5
6
7
8
Pin name
PIN1
PIN2
PIN3
PIN4
PIN5
TALLY *1
ENABLE *2
GND
The 6th pin terminal controls turning on or off the tally lamp
(available to control even when the 7th pin terminal is invalid).
The 7th pin terminal makes the external control valid/invalid.
Make sure to control the terminal by the MAKE system.
To assign the functions to the pin terminals
Serial
communication
*1
For a monitor connected to a personal computer etc, select
the terminal the equipment is actually connected to. For other
monitors, select “RS485.”
Control priority is as follows.
MAKE > TRIGGER = serial communication = buttons and menu on
the monitor
● You can use external control even when “CONTROL LOCK” is set to
“VOL.LOCK” or “ALL LOCK.” (→ page 25)
● When the monitor is off (on standby), external control is not
available. But certain external controls (starting/terminating
communication, turning on the monitor) are available through the
serial communication. (→ page 29)
<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated
controller*2.
● “Using the MAKE/TRIGGER system” on the right.
*2
Using the MAKE/TRIGGER
system
The controller is not commercially available. Consult your dealer if
you need it.
<Serial communication>
For the operation procedure, see page 18.
1 Select “REMOTE SETTING” on the SET-UP MENU.
2 Set “PARALLEL TYPE” to “SET.”
3 Select a pin name (“PIN1” – “PIN5”) for which you want
to assign a function, then select the function you want
to assign.
For the selectable functions, see the table on page 29.
Operation of the external control
1 Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE”
or “TRIGGER” in the SET-UP MENU.
2 Short-circuit the 7th pin terminal (ENABLE) to the
8th pin terminal (GND) so that the monitor can be
controlled by the external control.
3 When the “MAKE” system is selected:
Operate each function by short-circuiting the
corresponding pin terminal to the 8th pin terminal
(GND) or opening it.
When the “TRIGGER” system is selected:
Operate each function by pulse control, that is shortcircuiting the corresponding pin terminal to the 8th pin
terminal (GND) for about 1 second and opening it.
● When changing the input with MAKE system, only one pin terminal
must be short-circuited. (Other pin terminals must be opened.)
● When selecting the “TRIGGER” system, you can operate only one
PC, etc.
function at a time. Operate the functions one by one.
RS-485 IN
or
RS-232C
RS-485
OUT
RS-485
IN
RS-485
OUT
RS-485
IN
RS-485
OUT
● For the details, see page 28.
26
DT3D24G1_EN.indb 26
11.1.25 0:53:55 PM
<Functions controlled by the MAKE/TRIGGER system>
Display
Functions to be controlled
TALLY SEL
Selects the color of the tally lamp
SDI 1/L
SDI 2/R
DVI
3D
MIX
3D FORMAT
3G-B.DS
DUAL LINK
MARKER
FRAME
C.MARKER
MARK.SEL
ASPECT
1:1
STATUS
L.METER
TIME CODE
SOURCE ID
PARA.WFM
PARA.VS
BAL.WFM
BAL.VS
COLOR OFF
SCR CHECK
I/P MODE
MUTING
DIMMER
−−−
Changes the input to “SDI 1/L”
Changes the input to “SDI 2/R”
Changes the input to “DVI”
Activates/Deactivates the 3D mode
Activates/Deactivates the MIX mode
3D format 1/3D format 2 change *3
Selects the data stream of “3G SDI LEVEL B”
Turns on or off “SDI DUAL LINK”
Displays the area and safety markers
Indication of the area of the specified aspect ratio
The center marker indication
Selects the items of “MARKER” *4
Changes the aspect ratio
Displays in 1:1 mode
Status display *5
Audio level meter display
Time code display
→ “SOURCE ID” in “INFORMATION” on page 24
Displays the wave form monitor (Normal or Parallel)
Displays the vector scope (Normal or Parallel)
Displays the wave form monitor (Normal or Difference)
Displays the vector scope (Normal or Difference)
Color off
Screens check
Change a mode according to the input picture
Muting on/off
Change the intensity of the button lamps
No function
*3
*4
*5
*6
*7
*8
Opening
Short-circuiting
Green
Red
Invalid
Valid
Invalid
Valid
Invalid
Valid
Off
On
Off
On
FORMAT1
FORMAT2
DS1
DS2
Off
On
Off
On
Off
On
Off
On
Non-“R-” items
“R-” items
4:3
16:9
Off
On
→ “On the Status Display” on page 11
*6
Off
On
*7
*8
Color
Monochrome
*9
*10
Off
NORMAL
—
On
DARK
—
The 3D format changes in the same way as the SELECT button pressed in 3D mode.
Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (→ “MARKER” on page 20).
Displays the information shown when INPUT SELECT button of the current input is pressed (→ “On the Status Display” on page 11). While
controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.
While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When
“LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the
pattern of the audio channel display is switched.
While controlling with the MAKE system, the available set-up options will be the setting value currently selected in “SOURCE ID” (“ON” or
“AUTO” [short-circuiting]) and “OFF” (opening). While controlling with the TRIGGER system, uses the same set-up option as those in the SETUP MENU (→ “SOURCE ID” in “INFORMATION” on page 24).
While controlling with the TRIGGER system, the display mode changes in the same way as for the normal SCOPE function. (→ e on page 9)
While controlling with the MAKE system, the displayed (short-cirtuiting)/hidden (opening) operations are performed as follows regardless of
the MAIN MENU “AUTO OFF” setting:
[PIN 1] − [PIN 5] settings
Priority when the settings a re configured simultaneously
PARA.WFM PARA.VS BAL.WFM
BAL.VS
Wave form Vector Wave form Vector
Invalid
Wave form monitor > Vector scope
monitor
scope
monitor
scope
MIX
Parallel
Parallel Difference Difference
mode
Parallel wave
Difference wave
Parallel
Difference
Valid wave form vector wave form vector
>
>
>
form monitor
form monitor
vector scope
vector scope
monitor
scope
monitor
scope
Display
*9
While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While
controlling with the TRIGGER system, the screen changes in the same way as when pressing SCREENS CHECK button (→ w on page 9).
*10 Must be controlled with the TRIGGER system. The mode changes in the order of “NORMAL” → “CINEMA” → “FIELD” (This function cannot be
controlled with the MAKE system).
● You cannot assign the same function to different pin terminals.
● The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and opening it.
27
DT3D24G1_EN.indb 27
11.1.25 0:53:55 PM
External Control (cont.)
Using the serial communication
You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal.
● Consult your dealer for the details of the external control specification.
<Communication specifications>
Input terminal
RS-485
RS-232C
Cable
A straight LAN cable
A straight cable with a D-sub 9-pin connector (male
for the monitor, female for the personal computer
etc.)
Terminal
specification
Communication specifications
→ See below
Baud Rate: 4800 bps
Data Bits: 8 bits
Parity: No parity
Stop Bits: 1 bit
Flow Control: No control
Communication Code: ASCII Code
<Specifications of the RS-485 terminal>
Pin No.
1
2
3
4
5
6
7
8
This is a female terminal.
IN terminal signal
TXD +
TXD −
RXD +
NC
NC
RXD −
NC
GND
OUT terminal signal
TXD +
TXD −
RXD +
NC
NC
RXD −
NC
GND
<Specifications of the RS-232C terminal>
Pin No.
1
2
3
4
5
6
7
8
9
This is a female terminal.
Signal
NC
RXD
TXD
NC
GND
NC
RTS
CTS
NC
● The 7th terminal and the 8th terminal are connected.
<Command outline>
All commands consist of the following segments.
Header
Monitor ID
Command ID
Function
Data
Cr (0Dh)
On Header
“!” : Operation commands from the personal computer, etc. (→ <Basic command list> on page 29)
“?” : Reference commands from the personal computer, etc.
“@” : Status returns from the monitor
To start communication, send the connection command from the personal computer etc. To terminate the communication, send the
termination command from the personal computer etc.
Example of communication procedures
1 Starting the communication: connection command (!00BCN1Cr)
2 Monitor’s status (@00BOKCr)
PC, etc.
Monitor
3 Selecting “SDI 1/L” input (!00BINACr)
4 Monitor’s status (@00BOKCr)
5 Terminating the communication: termination command (!00BCN0Cr)
6 Monitor’s status (@00BOKCr)
28
DT3D24G1_EN.indb 28
11.1.25 0:53:56 PM
<Basic command list>
No.
1
2
3
4
Commands
Functions
! * **1 B C N 1 Cr
! * **1 B C N 0 Cr
! *
**1
B I D S
E
T
x
! * **1 B I D R
E
T
Cr
x*2
Cr
Data
Starts communication (connection)
No data
Terminates communication (termination)
No data
Assigns the control ID
01 – 99
Initializes the control ID
No data
5
! * **1 B I D D
S
P
x
x*2 Cr
Displays/hides the ID
00: Hide
01: Display
6
! * **1 B I D C
H
K
x
x*2 Cr
Flashes/hides the selected ID No. of the monitor
00: Hide
01: Display
7
8
9
10
11
12
13
14
15
16
17
18
! * **1 B M E N
U
Cr
Displays the MAIN MENU/Quits the menu operation
Moves the cursor downward ( )
No data
Cr
Moves the cursor downward ( )
No data
No data
! * **1 B U P Cr
! * **1 B D O W N
! *
**1
No data
B A D J
R
Cr
Makes setting/adjustment ( )
! * **1 B A D J
L
Cr
Makes setting/adjustment ( )
No data
! * **1 B S E T
U
P
Displays the SET-UP MENU
No data
Turns on the monitor
No data
! *
**1
Cr
B P W 1 Cr
! * **1 B P W 0 Cr
Turns off the monitor (on standby)
No data
! * **1 B I N A Cr
Selects “SDI 1/L” input
No data
! * **1 B I N B Cr
Selects “SDI 2/R” input
No data
! *
**1
B I N C Cr
! * **1 B D I S
P
Cr
19 ! * **1 B A M U
T
E
x
20 ! * **1 B A S P
x
x*2
Cr
21 ! * **1 B R O P O
S
I
x*2 Cr
x
22 ! * **1 B R O P
U
S
H
x
23 ! * **1 B S E L
E
C
T
Cr
24 ! * **1 B 3 D S
C
A
L
E
25 ! * **1 B 3 D x x*2 Cr
26 ! * **1 B C A M E
27 ! * **1 B M I X
x
R
x*2
A
Cr
Cr
x
x*2
x
x
x*2
Cr
x*2
Selects “DVI” input
No data
Displays the status *3
No data
Turns muting on/off
00: Off
01: On
Changes the aspect ratio
00: 4:3
01: 16:9
Cr Configures POSITION settings
Configures PUSH SEL. settings
Cr
−999 – +999
00: Change selection,
01: Reset the position
Operates the SELECT keys
No data
Changes 3D cursor mode
00: Off
01: Cursor mode
02: Grid mode
Changes 3D mode
00: Off
01: On
Displays the CAMERA ASSIST MENU
No data
Changes MIX mode
00: Off
01: On
● “Cr” is 0Dh.
● The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the
monitor (No. 13) can be used while the monitor is off (on standby).
*1
*2
*3
Enter the monitor’s ID for “**.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for
controlling all monitors at once.
Enter the appropriate data to “xx.”
Displays the information shown when the INPUT SELECT button currently lit is pressed (→ “On the Status Display” on page 11).
29
DT3D24G1_EN.indb 29
11.1.25 0:53:56 PM
Troubleshooting
Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the
monitor and consult an authorized dealer or service center.
Symptom
Cannot turn on the unit.
No picture with the power on.
No sound.
“Out of range” appears.
“NO SYNC” appears.
Wrong color, no color.
The picture becomes blurred.
Wrong picture position, wrong
picture size.
For some signals, the picture
cannot be displayed fully in the
effective screen area. There is no
sure method to solve this problem.
Some items do not appear on
the menu.
Probable cause and corrective action
● Press the
button to turn it on.
● Plugs should be firmly inserted.
● Turn on the AC power switch on the back of this product.
● If you do not turn on the monitor by pressing the
button while the DC power is turned
on, disconnect the DC connector, set up the DC power within the operating range, and then
connect the connector again.
● Select the correct input using the INPUT SELECT buttons.
● Connect the signal cable firmly.
● Turn on the power of the connected component and set the output correctly.
● Check whether the input signal format is acceptable on the monitor.
● Adjust the volume level.
● Deactivate the muting function.
● Connect the signal cable firmly.
● Turn on the power of the connected component and set the output correctly.
● Input a signal compatible with the unit.
● Select the correct input using the INPUT SELECT buttons.
● Connect the signal cable firmly.
● Turn on the power of the connected component and output video signals. Or, check whether
the video output of the component (video output setting of the VCR or graphic board of the
computer) is set correctly.
● Adjust each picture adjustment knob on the front panel or adjust the items of “PICTURE SUB
ADJ.” in the SET-UP MENU. Or, perform “reset” in “PICTURE SUB ADJ.”
● Check whether the setting of COLOR OFF or SCREENS CHECK buttons are appropriate.
● Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU. Or, perform “reset” in “WHITE
BALANCE SET.”
● Adjust the picture contrast or brightness by using the adjustment knobs on the front panel.
Or, adjust “CONTRAST” or “BRIGHT” of “PICTURE SUB ADJ.” in the SET-UP MENU.
● Check whether the setting of 1:1 is appropriate.
● Check “ASPECT” of the MAIN MENU, and “ SD4:3 LARGE “ under the SET-UP MENU “FUNCTION
SETTING.”
● Check whether the input signal format is acceptable on the monitor.
● The items which are not available for the current input or the current input signal are not
displayed on the menu. Change the input or the input signal.
● The items controlled by the MAKE system do not appear on the menu.
● Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”
Buttons on the monitor do not
● You cannot use the buttons for the items controlled by the MAKE system. Disable the external
work.
control.
● Press the 3D button to enter the 3D mode.
● Press the SELECT button to change the 3D viewing format (when inputting existing 3D images).
3D viewing is not available.
● Set the 3D format compatible with input images in “SDI FORMAT 1/SDI FORMAT 2” or “DVI
FORMAT 1/ DVI FORMAT 2” under the MAIN MENU “3D SETTING.”
● Press the MIX button to enter the MIX mode.
● Input L and R images in the same format compatible with the MIX mode.
Cannot enter the MIX mode.
● Input 3G SDI LEVEL B Dual Stream into the SDI IN 1/L terminal.
The image is distorted or cannot ● Set “FRAME SYNC.” under the MAIN MENU “3D SETTING” to “ON” or “OFF.”
Page
9
7
7
9
7
—
33, 34
8
9
7
—
11, 33,
34
9
7
—
8, 23
9
23
8, 23
9
20, 23
33, 34
—
26
25
26, 27
9, 13
9, 13
19
9, 13
33
—
19
be synchronized in MIX mode.
The following are not malfunctions.
● When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed.
Though the remaining picture will disappear after a while, there may be a case that it remains for a long period
depending on the length of time the still image was displayed for. This is due to the characteristics of the LCD
display and is not a malfunction.
● Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a
problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be
missing or constantly lit.
● The following symptoms are problems only when pictures or sounds are not played back normally.
●
●
●
●
A slight electric shock occurs when you touch the monitor.
The top and/or rear panel of the monitor becomes hot.
The monitor emits a cracking noise.
The monitor emits a mechanical noise.
30
DT3D24G1_EN.indb 30
11.1.25 0:53:57 PM
Self-check program
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a
problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the
problem.
When the screen goes blank, and one or some of the INPUT SELECT lamps (SDI 1/L, SDI 2/R, DVI) on the front control panel start flashing...
1
2
3
4
5
Check which lamps are flashing.
Press
button to turn off (on standby) the monitor.
Turn off the AC power switch on the rear panel.
Disconnect the AC power cord from the AC outlet.
Contact your dealer with the information about which lamps were flashed.
● If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT lamps may flash and no image may
be displayed.
When this happens, turn off power and wait at least 10 seconds before turning on the monitor again.
If the INPUT SELECT lamps do not flash, you can use the monitor as normal.
31
DT3D24G1_EN.indb 31
11.1.25 0:53:57 PM
Specifications
General
Model name
Type
Screen size
Aspect ratio
Compliant video signal format
Format
DT-3D24G1
MULTI FORMAT 3D LCD MONITOR
Type 24 wide format
16:10
→ “Available signals” on page 33
3G SDI
DUAL LINK HD SDI
HD SDI
SD SDI
EMBEDDED AUDIO
:
:
:
:
SMPTE424M/SMPTE425M
SMPTE372M
BTA S-004C, SMPTE292M
ITU-R BT.656:
525/625
SMPTE259M:
525
: SMPTE299M, SMPTE272M
Audio output
Internal speaker: 1.0 W + 1.0 W
Operation environment
Operating temperature: 5°C – 35°C (41°F – 95°F)
Operating humidity: 20% – 80% (non-condensing)
(Slightly variable depending on ambient conditions for installation.)
Power requirements
AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz, or DC 24 V (Voltage range: DC 23.3 V − DC 25.5 V)
Rated current
1.15 A (AC 120 V)
0.67 A (AC 220 – 240 V)
4.8 A (DC 24V)
External dimensions (excluding
protruding parts)
Width: 564 mm (22 1/4˝)
Height: 448.6 mm (17 3/4˝)
Depth: 243 mm (9 5/8˝)
(with the stand)
Mass
Accessories
12.0 kg (26.4 lbs) (with the stand) 9.1 kg (20.0 lbs) (without the stand)
564 mm (22 1/4˝)
408 mm (16 1/8˝)
99 mm (4˝)
(without the stand)
AC power cord, Power cord holder × 1, Screw × 2 (for power cord holder),
Circular polarizing glasses × 2 (for 3D viewing, not under warranty)
LCD panel
Type
Effective screen size
Number of pixels displayed
Number of colors displayed
Contrast ratio (TYP.)
24˝ wide, active matrix TFT
Width: 518.4 mm (20 1/2˝) Height: 324 mm (12 7/8˝) Diagonal: 611.3 mm (24 1/4˝)
1920 × 1200
16.77 million
1000:1
Input/output terminals
External control
Audio
Video
DVI-D (HDCP)
DVI-D signal input (compatible with HDCP): DVI-D connector x 1 (compatible with DDC2B)
E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1/L) Digital signal input (compatible with EMBEDDED AUDIO/DUAL LINK signals):
E. AUDIO 3G SDI/HD SDI/SD SDI (IN 2/R) Auto detection, 2 line, BNC connector x 2
E. AUDIO 3G SDI/HD SDI/SD SDI
(ACTIVE OUT)
Digital signal output (compatible with EMBEDDED AUDIO signals):
2 line reclocked out, BNC connector x 2
AUDIO (IN)
Analog audio signal input: 1 line, RCA connector x 2,
500 mV (rms), high impedance
AUDIO (MONITOR OUT)
Analog audio signal input: 1 line, RCA connector x 2,
500 mV (rms)
REMOTE (MAKE/TRIGGER)
→ “Using the MAKE/TRIGGER system” on page 26
REMOTE (RS-485)
REMOTE (RS-232C)
→ “Using the serial communication” on page 28
32
DT3D24G1_EN.indb 32
11.1.25 0:53:57 PM
Available signals
The following signals are available for this monitor.
Video signals
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
*1
*2
*3
*4
Signal name
480/60i
480/59.94i
576/50i
480/60p
480/59.94p
576/50p
640*480/60p
640*480/59.94p
720/60p
720/59.94p
720/50p
720/30p
720/29.97p
720/25p
720/24p
720/23.98p
1080/60i
1080/59.94i
1035/60i
1035/59.94i
1080/50i
1080/60p
1080/59.94p
1080/50p
1080/30p
1080/29.97p
1080/25p
1080/24p
1080/23.98p
1080/30psF
1080/29.97psF
1080/24psF
1080/23.98psF
1080/25psF
√ : Acceptable
— : Not acceptable
Input terminals
Signal format shown
E. AUDIO SDI (IN 1, IN 2)*1
in the status display
(→ page 11)
SD/HD (1.5G)
3G SDI
DUAL LINK
MIX
480/60i
480/59.94i
576/50i
480/60p
480/59.94p
576/50p
640*480/60p
640*480/59.94p
720/60p
720/59.94p
720/50p
720/30p
720/29.97p
720/25p
720/24p
720/23.98p
1080/60i
1080/59.94i
1035/60i
1035/59.94i
1080/50i
1080/60p
1080/59.94p
1080/50p
1080/30p
1080/29.97p
1080/25p
1080/24p
1080/23.98p
1080/30psf
1080/29.97psf
1080/24psf
1080/23.98psf
1080/25psf
√
√
√
—
—
—
—
—
√
√
√
√
√
√
√
√
√
√
√
√
√
—
—
—
√
√
√
√
√
√ *2
√ *3
√
√
√ *4
—
—
—
—
—
—
—
—
√
√
√
√
√
√
√
√
√
√
—
—
√
√
√
√
√
√
√
√
√
√ *2
√ *3
√
√
√ *4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
√
√
—
—
√
√
√
√
√
√
√
√
√
√ *2
√ *3
√
√
√ *4
—
—
—
—
—
—
—
—
√
√
√
√
√
√
√
√
√
√
—
—
√
√
√
√
√
√
√
√
√
√ *2
√ *3
√
√
√ *4
DVI-D (HDCP) (Digital
component/Digital RGB)
√
√
√
√
√
√
√
√
√
√
√
—
—
—
—
—
√
√
—
—
√
√
√
√
√
√
√
√
√
—
—
—
—
—
Compatible with EMBEDDED AUDIO signals.
If there is no payload ID, the signal is regarded as 1080/60i, and “1080/60i” and the status appear.
If there is no payload ID, the signal is regarded as 1080/59.94i, and “1080/59.94i” and the status appear.
If there is no payload ID, the signal is regarded as 1080/50i, and “1080/50i” and the status appear.
Notice on transportation
This monitor is precision equipment and needs dedicated packing material for transportation.
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.
● For easy understanding, pictures and illustrations are emphasized, omitted or composed, and may be slightly different from actual
products.
● Design and specifications are subject to change without notice.
● All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or
registered trademarks of their respective companies.
33
DT3D24G1_EN.indb 33
11.1.25 0:53:58 PM
Specifications (cont.)
Computer signals (preset)
DVI-D (HDCP) terminals
No.
Signal name
Resolution
Horizontal
Vertical
Frequency
Horizontal (kHz)
Vertical (Hz)
Scan system
1
VGA60
640
480
31.5
59.9
Non-interlace
2
WVGA60
852
480
31.5
59.9
Non-interlace
3
SVGA60
800
600
37.9
60.3
Non-interlace
4
XGA60
1024
768
48.4
60.0
Non-interlace
5
WXGA (1280)
1280
768
47.8
60.0
Non-interlace
6
WXGA+60
1440
900
55.9
60.0
Non-interlace
7
SXGA60
1280
1024
64.0
60.0
Non-interlace
8
WSXGA+60
1680
1050
65.2
60.0
Non-interlace
9
UXGA60
1600
1200
75.0
60.0
Non-interlace
10
WUXGA60
1920
1200
74.0
60.0
Non-interlace
11
720/60p
1280
720
45.0
60.0
Non-interlace
12
1080/60p
1920
1080
67.5
60.0
Non-interlace
13
720/50p
1280
720
37.5
50.0
Non-interlace
14
1080/50p
1920
1080
56.25
50.0
Non-interlace
● Non-preset signals may not be displayed normally.
● When a preset signal comes in, the signal format is shown on the status display. For other signals, the resolution is shown.
Specification of the DVI-D (HDCP) terminal
Connect it to the DVI-D output terminal on a personal computer.
Pin
No.
1
2
3
4
5
6
7
8
T.M.D.S Data 2–
9
10
11
12
13
14
15
16
T.M.D.S Data 2+
T.M.D.S Data 2 shield
NC
NC
DDC Clock
DDC Data
NC
Dimensions
Input signal
T.M.D.S Data 1–
T.M.D.S Data 1+
T.M.D.S Data 1 shield
NC
NC
+5 V Power
GND
Hot Plug Detect
Pin
No.
17
18
19
20
21
22
23
24
Input signal
T.M.D.S Data 0–
T.M.D.S Data 0+
T.M.D.S Data 0 shield
NC
NC
T.M.D.S Clock shield
T.M.D.S Clock+
T.M.D.S Clock–
Unit: mm (inch)
<Front view>
<Side view>
<Rear view>
99 (4)
51.9 (2 1/8)
1.3 (1/16)
100
VESA mounting holes
(Size: 4-M4, depth: 10 mm)
117 (4 5/8) 100
408 (16 1/8)
564 (22 1/4)
448.6 (17 3/4) (High)/
413.6 (16 3/8) (Low)
Pin
No.
Input signal
51 (2 1/8)
300 (11 7/8)
243 (9 5/8)
34
DT3D24G1_EN.indb 34
11.1.25 0:53:58 PM
DT3D24G1_EN.indb 35
11.1.25 0:53:59 PM
MULTI FORMAT 3D LCD MONITOR
DT-3D24G1
© 2011 Victor Company of Japan, Limited
DT3D24G1_EN.indb 36
0111SKH-MW-MT
11.1.25 0:53:59 PM