Motorola 4500 manual
Advertisement
Advertisement
739K01 3/9/0 10:01 AM Page 2
Table of Contents
Getting Started .....................................................4
Welcome ................................................................4
General Safety Information....................................6
Introduction ..........................................................11
Phone Overview ..................................................12
Basic Operation .................................................15
Turn Phone On and Off .......................................15
Place a Call..........................................................17
Automatic Redial..................................................18
End a Call ............................................................19
Receive a Call......................................................19
Call in Absence Indicator.....................................19
Hands Free Operation (with optional
HF Microphone) ...................................................20
Place a Hands Free Call......................................20
Receive a Hands Free Call..................................20
Manual Handset to Hands Free Operation..........20
Automatic Hands Free ........................................21
Enhanced Simplex Hands Free ...........................21
Signal Strength Meter ..........................................22
Volume Meter ......................................................22
Speaker Volume ..................................................23
Earpiece Volume .................................................23
Ringer Volume .....................................................24
Display Own Phone Number ...............................24
Switch to Second Phone Number........................24
Memory ...............................................................26
Storing Information in Memory ............................26
Selecting a Memory Location ..............................26
Store to a Location Number.................................26
Memory Autoload.................................................27
Storing a Phone Number and a Name ................27
1
739K01 3/9/0 10:01 AM Page 2
Table of Contents
Memory Protect ...................................................29
Recalling/Scrolling from Memory .........................29
Recalling/Scrolling by Location Number ..............29
Last Number Recall .............................................30
Recalling Last 10 Numbers Dialed ......................30
Super Speed Dialing............................................31
Turbo Dial ............................................................31
One-Touch Dialing Keys......................................32
One-Touch Priority Dialing...................................33
Scratch Pad Memory ...........................................33
Tone Dialing (Two-Part Calling)...........................34
Pause Dialing (Memory Linking)..........................35
Edit a Memory Location .......................................37
Clear Memory Entries ..........................................38
Features ..............................................................39
Select/Cancel Menu Features .............................39
Signal Strength Meter (SSM)...............................39
Feature Status Review ........................................40
Battery Indicator...................................................40
Extended Talk Time.............................................41
Microphone Muting ..............................................41
Number Preference .............................................41
Automatic Answer ................................................42
Multiple Key Answer ............................................42
Incoming Call Screening......................................43
Silent Ringer ........................................................43
Distinctive Ringer .................................................44
Silent Keypad.......................................................45
Silent Scratch Pad ...............................................45
PIN Code Activation.............................................46
Timers ..................................................................47
Individual Call Timer ............................................47
Resettable Call Timer ..........................................47
2
Table of Contents
Cumulative Call Timer .........................................48
Individual Display Timer.......................................48
One-Minute Timer ................................................49
Security Features.................................................49
Electronic Lock ....................................................49
Change Unlock Code...........................................50
Display Unlock Code ...........................................50
Automatic Lock ....................................................50
Language Selection .............................................51
Auxiliary Alert .......................................................51
Change Service Level..........................................52
Master Reset .......................................................53
Master Clear ........................................................55
Reference............................................................56
The Cellular System ............................................56
Service Area ........................................................56
Weak Signal Alert ................................................56
Switchhook and Enhanced System Services ......57
Roaming...............................................................57
Selectable System Registration...........................57
Preferred SIDS ....................................................60
Troubleshooting ...................................................61
Quick Reference Feature Guide ..........................62
Message Glossary ...............................................64
Index ....................................................................67
Consumer Update................................................70
Patent Information ...............................................78
3
739K01 3/9/0 10:01 AM Page 4
Getting Started
Welcome
Thank you for selecting Motorola – a world leader in cellular technology.
All Motorola cellular phones are designed and manufactured in the United States to meet
Motorola’s exacting specifications and world-class quality standards. These phones withstand our rigorous durability tests including temperature, humidity, shock, dust, vibration, and a drop test.
Product superiority is yours with Motorola.
•For information about your product or accessories for your product, please call Motorola at:
1-800-331-6456 TTY: 1-888-390-6456
1-800-461-4575 (Canada)
Please visit us at: www.mot.com
• For any information about your cellular service, please call your service provider (Carrier).
Carrier’s Name ________________________
Carrier’s Phone Number _________________
Getting Started
• You will need to have the following information when you inquire about your phone or service.
Your ESN (electronic serial number) and MSN
(mechanical serial number) are located on the transceiver of your telephone.
ESN Number_____________________________
MSN Number ____________________________
Model Number ___________________________
Cellular Phone Number ____________________
• Unlock Code — The sequential code of 123 is the standard unlock code programmed into all phones by the factory. It is often changed to the last three digits of your cellular phone number by the carrier. For easy access to this unlock code in the future, please list it here now: __ __ __.
(Please contact your place of purchase if your unlock code has been changed and you do not have this information.)
Warranty Expiration Date ________________
Date of Purchase ______________________
4 5
739K01 3/9/0 10:01 AM Page 6
Getting Started
General Safety Information
IIM PO AN T
S affe orrm attiio
Read this information before using your wireless mobile phone.
Exxp ossu Ra diio Frre qu Siig allss
Your wireless mobile telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals.
International agencies have set standards and recommendations for the protection of public exposure to RF electromagnetic energy.
International Commission on Non-Ionizing
Radiation Protection (ICNIRP)1996
• Verband Deutscher Elektrotechniker (VDE)
DIN-0848
• United States Federal Commission, Radio
Frequency Exposure Guidelines (1996)
• National Radiological Protection Board of the
United Kingdom, GS 11, 1988
• American National Standards Institute (ANSI)
IEEE. C95. 1-1992
• National Council on Radiation Protection and
Measurements (NCRP). Report 86
• Department of Health and Welfare Canada.
Safety Code 6
6
Getting Started
These standards are based on extensive scientific review. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the updated ANSI standard.
The design of your phone complies with these standards when used as described under "Phone
Operation."
A ntte nn a C
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate local agency regulations.
IMPORTANT
C arrrryy P on e O pe attiio n
Do not operate your carry phone when a person is within 8 inches (20 centimeters) of the antenna. A person or object within 8 inches (20 centimeters) of the antenna could impair call quality and may cause the phone to operate at a higher power level then necessary and expose that person to
RF energy in excess of that established by the
FCC RF Exposure Guidelines.
M ob e P ho e O pe attiio n
Do not operate your mobile telephone when any person is within 12 inches (30 centimeters) of its vehicle-installed antenna.
7
739K01 3/9/0 10:01 AM Page 8
8
Getting Started
Drriivviin g
Check the laws and regulations on the use of wireless telephones in the areas where you drive.
Always obey them. Observe the following guidelines when using your phone while driving.
• Give full attention to driving--driving safely is your first responsibility.
• Use hands-free phone operation, if available.
• Pull off the road and park before making or answering a call if driving conditions so require.
eccttrro niicc D
Most modern electronic equipment is shielded from RF signals. However, certain equipment may not be shielded against the RF signals from your wireless phone.
P acce errss
The Health Industry Manufacturers Association recommends that a minimum separation of six inches (6") be maintained between a wireless phone's antenna and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of
Wireless Technology Research.
Persons with pacemakers:
• should ALWAYS keep the phone more than six inches from their pacemaker when the phone is turned ON
• should turn the phone OFF immediately if you have any reason to suspect that interference is taking place
Getting Started
Otth err M diicca ess
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from external
RF energy. Your physician may be able to assist you in obtaining this information.
Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.
V eh
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle.
P osstte d F ess
Turn your phone OFF in any facility where posted notices so require.
assttiin g A ass
To avoid interfering with blasting operations, turn your phone OFF when in a "blasting area" or in areas posted: "Turn off two-way radio." Obey all signs and instructions.
P otte Attm ossp ess
Turn your phone OFF and do not remove your battery when you are in any area with a potentially explosive atmosphere. Obey all signs and instructions. Sparks from your battery in such areas could cause an explosion or fire resulting in
9
739K01 3/9/0 10:01 AM Page 10
Getting Started bodily injury or even death. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include, but are not limited to: fueling areas such as gasoline stations; below deck on boats; fuel or chemical transfer or storage facilities; areas where fuel odors are present (for example, if a gas/propane leak occurs in a car or home); areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you normally would be advised to turn off your vehicle engine.
F orr V ess E qu pp ed h a n A g
An air bag inflates with great force. Do NOT place objects, including both installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.
Getting Started
Introduction
The cellular telephone you have selected represents the state-of-the-art in cellular telephones today. The listing below shows just a few of the exceptional features that your telephone provides.
• Seven-character 14-segment LCD display
• 104 memories, including last number recall and scratch pad
• Three One-Touch Dial Keys
• Auto Answer
• Five Call Timers
• Two-system Registration
• Multiple Key Answer
• Distinctive Ringer Tones
To help you become familiar with your telephone’s features, this manual will take you through a logical step-by-step learning procedure. The tabs at the edge of the manual mark the different categories that the telephone’s operations have been broken into. The respective sub-categories are noted in black bars.
10 11
739K01 3/9/0 10:01 AM Page 12
Getting Started
Phone Overview
a Operating Display and Status Indicators
Provide a visual indication of telephone numbers and messages associated with mobile telephone service.
Power Light – Displays when a call is in progress.
In Use – Displays when a call is in progress.
No Svc – Displays when the unit is out of service range of a cellular system. Calls cannot be placed or received.
Roam – Displays when the unit is within range of a cellular system other than your home registered system.
b
Three One-Touch Dialing Keys
Allow direct access to important phone numbers and carrier network services.
c Volume Keys
Adjust earpiece, ringer, and speaker volume.
Also:
G scrolls forward.
H scrolls backward.
12
Getting Started a e
Fcn
1 menu
4
G
H
I
7
P
Q
R
S
2
A
B
C
5
J
K
L
8
T
U
V
0 opr
3
D
E
F
6
M
N
O
9
W
X
Y
Z
Recall Clear SEND
Power Store END b c d
13
739K01 3/9/0 10:01 AM Page 14
Getting Started d Control Keypad
R Recalls and displays telephone numbers stored in memory.
C Clears the last digit entered when pressed and released. Press and hold to clear the entire display.
S Initiates a call or answers a call.
P Turns the phone on and off.
s Stores telephone numbers into any of the memory locations.
E Terminates a call in progress.
e F Function Key
Used in combination with other buttons for specific user-programmed functions (e.g.,
F, 5 activates lock mode).
Basic Operation
Turn Phone On and Off
1. If installed in your vehicle, your phone should turn on and off with the vehicle’s ignition. If it does not, or if the phone is in a bag configuration, press
P
.
2. Press P again to turn unit off.
Start-up Self Tests
Each time the telephone is turned on, it performs a series of self tests, sounds a tone, and lights all display positions and status indicators to check their operation.
Display Messages
Message
A1 A2
•If your phone is programmed for two cellular systems, one of these messages will appear in the display upon power up.
B1 B2
•These are reminders as to which system and phone number are currently in use.
LOCKED
•Indicates that the phone has been locked and cannot send or receive calls until unlocked. Refer to page
49, "Electronic Lock".
14 15
739K01 3/9/0 10:02 AM Page 16
Basic Operation
Start-up Status Indicators
Indicators
In Use No Svc Roam
Explanation
On/Lock Indicator
(dot)
• Lights steadily to indicate the phone is on and fully operative
• Lights steadily to indicate the phone is locked and will not place calls
In Use No Svc Roam
In Use Indicator
• Lights steadily while a call is in progress
In Use No Svc Roam
In Use No Svc Roam
No Svc (No Service)
Indicator
• Lights steadily if phone is beyond range of a cellular service area
• Calls cannot be placed or received while No Svc is lit
Roam Indicator
• If flashing, you are accessing a service area outside of your home system.
• Steady Illumination —
Roaming on a home type system
• Flashing — Roaming on a non-home type system
16
Basic Operation
Place a Call
1. With power on, enter the number you wish to call.
2. Press S . (You may leave the handset mounted while dialing if an external microphone is present.)
The IIn party answers, bring the handset to your ear. Or leave the handset mounted and direct your conversation to the Hands Free microphone (if present) for a hands free call.
To Correct an Error
To clear the last digit entered, press and quickly release C .
To clear the entire entry, press and hold C until the entire entry is erased.
If Entering More Than Seven Digits
You can call a phone number with up to 32 digits, but only the last seven digits will display.
When recalling a stored phone number that is longer than seven digits, the display will flash the memory location number and the last ten digits of the number.
EXAMPLE Recall memory location 01 that contains the 14-digit number 12345678901234.
01 567 / 8901234 will alternately display.
To review the overflow digits from the above example, press R. The phone will take you back to the beginning of the phone number, then flash up to seven digits at a time – 1234567 / 8901234 – until the end of the stored phone number is reached.
17
739K01 3/9/0 10:02 AM Page 18
Basic Operation
Unsuccessful Call Attempts
If you hear one of the following signals, you have not successfully completed your call.
Description
Fast Busy
(reorder signal)
System
Busy
Alternating
High/Low
Tone
(intercept)
No
Service
Slow Busy
Signal
Cellular System Busy
Press S again before ending the unsuccessful call attempt to automatically redial the call (see
"Automatic Redial", below), or press
E and dial the call again.
Cellular System Could Not
Complete the Call
You may have tried to place a call before the ON/LOCK indicator was lit to let you know your phone was fully operative. Either press S again to redial, or press E and dial the call again.
Called Party’s Line is Busy
Automatic Redial
Your telephone includes a convenient feature designed to make repetitive call attempts when a cellular system is busy.
If you receive an alternating high/low signal
(intercept) or the fast busy tone (reorder signal) followed by snd to redial in the display when attempting to place a call and wish to retry the call, press S before ending the unsuccessful call attempt. Redial is then displayed.
Your telephone will make the call attempt continuously over the next four minutes. If four
18
Basic Operation minutes is insufficient time, press S to begin another cycle. If the call attempt is successful, the phone will ring to alert you of the connection.You
may terminate Automatic Redial by turning off the phone or by pressing E.
NOTE Automatic Redial applies when the system is busy and will not engage when the called party’s line is busy.
End a Call
Press E or return the handset to its mount.
activated the Automatic Hands Free feature, you must press E to terminate the call.
Receive a Call
Lift the handset to your ear or press S if an external microphone is present.
Power must be on to receive calls.
Call in Absence Indicator
If your phone is on and an incoming call is unanswered, Call is displayed.
Press C or E to cancel the message and clear the display.
In carry phone configuration, the display will go blank after 6 seconds in order to conserve battery energy.
Reactivate the display by pressing any key except C , E , or P .
NOTE The phone will not display or retrieve the phone number of the calling party.
19
739K01 3/9/0 10:02 AM Page 20
Basic Operation
Place a Hands Free Call
1. Leaving the handset mounted, dial the number you wish to call.
2. Press
S
.
3. When the called party answers, direct your conversation to the Hands Free microphone typically mounted on your vehicle’s sun visor. The In Use indicator will remain on and
HF will display for the duration of the call.
4. Press E to terminate the call.
Receive a Hands Free Call
1. Press S .
2. Direct your conversation to the Hands Free microphone. The In Use indicator will remain on and HF will display for the duration of the call.
3. Press E to terminate the call.
Manual Handset to Hands
Free Operation
1. To switch from the handset to Hands Free operation, press F , 6 .
Mute will display. Note that M for Mute appears on 6.
2. Return the handset to its mount.
3. Press F , 6 again and HF will display.
4. Direct your conversation to the microphone.
20
Hands Free Operation
(with optional HF Microphone)
Basic Operation
Automatic Hands Free
1. Press F ,
1
.
2. Scroll the menu by pressing G or H until
HF AUTO MUTE OFF displays.
3. Press s once to toggle this feature on, and
C to toggle it off.
4. To exit the Feature Menu, press E .
This feature allows you to automatically go to
Hands Free operation without pressing F, 6.
To switch from Hands Free to Handset operation, just lift the handset while in a call. To return to
Hands Free operation, hang up the handset and begin speaking.
Enhanced Simplex Hands Free
In certain systems, you may experience audio feedback while using Full Duplex Hands Free operation, the normal operating mode. This situation can usually be alleviated by slightly reducing the speaker volume. In extreme cases, you may want to switch to Enhanced Simplex
Hands Free operation. This operation will not allow interruption of the party that is speaking.
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
HF FULL DUPLEX displays.
3. Press C once to toggle this feature off, and s to toggle it on. When you deactivate the HF Full Duplex the display will show
HF SIMPLEX
4. To exit the Feature Menu, press E .
21
739K01 3/9/0 10:02 AM Page 22
Basic Operation
Signal Strength Meter
The Signal Strength Meter (SSM) represents the relative strength of the signal received by your phone. The SSM is displayed as a bar graph following the letter S at the left side of the display.
The S alone represents the lowest strength with each additional bar representing a stronger signal.
S s – – = = ≠ ≠
Weak Signal Strong Signal
The SSM appears every time you turn your phone on, unless this feature is turned off through the
"Feature Menu" (refer to page 39).
To best utilize the SSM, you should familiarize yourself with the relative signal strength levels and their associated call-in-progress qualities.
Any messages, such as LOCKED, which display as a result of activation of a feature will take priority over the SSM. You will not see the SSM displayed in these cases.
Volume Meter
The Volume Meter represents the current volume setting and will display whenever you adjust the volume control. The volume level is displayed as a bar graph following the letter V at the left side of the display, with each additional bar representing a higher volume setting.
22
Basic Operation v v – – = = ≠ ≠
Lowest Volume
Setting
Highest Volume
Setting
The number of bars represents the number of volume steps for speaker, earpiece, and ringer volume. The volume levels can be adjusted by the use of G and H.
Speaker Volume
1. With the handset mounted, press and hold
G to raise the volume.
2. To lower the volume, press and hold H .
The number of bars on the Volume Meter will decrease.
The maximum number of bars that will display is four.
v
– – = =
Earpiece Volume
Lift the handset and use G and H as described above.
The maximum number of bars that will display is five.
v
– – = = ≠
23
739K01 3/9/0 10:02 AM Page 24
Basic Operation
Ringer Volume
Press F and use G and H as described in the "Volume Meter" on page 22.
The maximum number of bars that will display is six.
v
– – = = ≠ ≠
Display Own Phone Number
1. Press
R
,
#
.
The phone number that is currently active will be displayed.
2. When you have finished viewing, press C .
Switch to Second Phone Number
1. Press R , # , s .
The display will go blank to confirm the switch and the newly activated number will display.
2. When you have finished viewing, press C .
Your telephone can operate over two different home systems, if you have made proper arrangements with your Cellular System Operator.
Both are designated as your "home system" but are accessed with separate telephone numbers.
While you may switch from one system to the other, only one of the two can be active at any given time. Calls are placed and received through the active system only.
24
Basic Operation
If you have two phone numbers programmed into your phone, each time the telephone is turned on, it displays a message indicating which home system type and phone number is currently active.
The message shows the system type and phone number applied, as follows:
System Type and
Phone Number
Non-wireline or A type with phone number 1
A1
Display
Non-wireline or A type with phone number 2
Wireline or B type with phone number 1
Wireline or B type with phone number 2
A2
B1
B2
If a call is placed to the inactive phone number, the caller will receive the recorded "Not In Service" message.
When you turn your phone on, the telephone will remember which system was active when you turned it off. That system will stay active until you change to the other system with the sequence R,
#, s. However, you cannot switch systems during a call.
25
739K01 3/9/0 10:02 AM Page 26
Memory
Storing Information in Memory
Your telephone provides memory capable of storing up to 99 frequently called phone numbers as well as a seven-character name tag. Upon entering a phone number in memory, the phone will prompt you to store an associated name. If you are not interested in creating a name tag for the selected location, alpha entry may be bypassed and the phone number alone can be stored.
Selecting a Memory Location
There are two ways to select a memory location:
• select a specific location number
• autoload to store the information in the next sequentially available location.
Store to a Location Number
1. Enter phone number to be stored, up to 32 digits.
2. Press s .
3. Enter the two-digit location number in which you wish to place the entry.
4. The phone is automatically in Alpha Entry
Mode. Enter a name, or bypass Alpha, go to step 5.
5. Press s .
Phone will confirm storage by displaying memory location number.
NOTE If FulL displays, refer to "Memory Protect" on page 29.
Memory
Memory Autoload
1. Enter phone number to be stored.
2. Press s , * .
3. The phone is automatically in Alpha Entry
Mode. Enter a name or continue to step 4.
4. Press s .
Phone will confirm storage by displaying the autoload memory location number.
NOTE If FulL displays, refer to "Memory Protect" on page 29.
This procedure automatically stores memory entries into the next available memory location.
This method serves particularly well if you do not remember the next available memory location.
Storing a Phone Number and a Name
1. Enter phone number to be stored.
2. Press s .
3. Enter two-digit location number or press * for Autoload.
The phone will then automatically prompt for alphabetic name input. The Alpha Entry Mode display will flash ALPHA –.
4. Utilize the alphanumeric keypad to enter up to 7 letters as described in the example on page 28. # advances to the next position.
* backspaces, if necessary. Repeat until name tag is complete.
5. Press s
.
Phone will confirm storage by displaying memory location number.
27
739K01 3/9/0 10:02 AM Page 28
Memory
Key
7
8
9
2
3
4
5
6
NOTE Your phone is capable of storing up to 32 numeric characters or a combination of 16 numeric and seven alpha characters per memory location.
Details on Utilizing Alpha Entry Mode
Once in Alpha Entry Mode, you can enter letters using your numeric keypad. For example, "A" is at the first press of 2, "B" is at the second press of
2, and "C" is at the third press of 2.
4th
Press
1st
Press
T
W
M
P
G
J
A
D
2nd
Press
U
X
N
Q
H
K
B
E
3rd
Press
V
Y
O
R
I
L
C
F
S
Z
EXAMPLE To enter "Bob" and his phone number
555-1234 into memory location 01:
1. Enter phone number by pressing 5, 5, 5,
1, 2, 3, 4.
2. Press s, 0, 1. The display will flash
ALPHA –.
3. Press 2 twice to select "B". Press # to advance to the next position. Press 6 three times for "O". Press #. Press 2 twice more to select the second "B".
28
Memory
4. Press s. The display will flash 01 to confirm that the name and phone number were successfully stored in memory location 01.
NOTE If FulL displays, refer to "Memory Protect" below.
Memory Protect
The directory has an automatic memory protect feature which prevents the accidental overwriting and loss of previously stored names and numbers in memory. If you attempt to store a number or name in a location that already contains an entry, the phone will display FULL, and the name/number in that memory location. The display will then alternate between the previously stored number and CHANGE?.
If you wish to save to that location, thus erasing the old information, press s. If you wish to store the entry in an alternate location, Press E, s and the alternate location number.
Recalling/Scrolling from Memory
Information stored in memory can be recalled or reviewed by location number. You may also scroll the memory during a call. Pressing E once in this case will cancel scrolling, but not the call.
Recalling/Scrolling by
Location Number
1. Press R .
2. Enter the desired two-digit location number. or
29
739K01 3/9/0 10:02 AM Page 30
Memory
Press 0 ,
1 and press # or G to begin scrolling from the beginning of the stored locations.
The display will show the location number, then the first ten digits of the number. If Number
Preferred is not selected, up to seven characters of the name will display. (Refer to "Number
Preference" on page 41 for more details.)
3. Press S to place a call to the number displayed.
Use G and H to scroll forward and backward.
To scroll from a specific two-digit location, press
R, then the location number where you wish to begin scrolling.
The phone will display an apostrophe ( ’) after the memory location number to indicate that memory scrolling is active.
Last Number Recall
1. Press R, and the last number entered on the keypad will appear.
2. Press S to place a call to the last number displayed.
Recalling Last 10 Numbers Dialed
1. Press R , 0 , 0 .
The display will show L0’ followed by the name or number of the most recently placed call.
2. Scroll the last ten numbers dialed with * and # .
3. To place a call to this number, press S .
30
Memory
This feature allows you to refer to or redial any of the last ten numbers to which calls were placed.
The numbers are stored in the order placed and always represent the ten most recent calls.
Successive calls to the same number are stored only once, and all are retained when the unit is shut off.
NOTE When scrolling, you may observe that a location number is skipped. This may be caused by pressing
S when the display is empty and does not mean that a number has been lost.
Super Speed Dialing
1. Enter the location number.
2. Press S .
Memory locations 1-99 are equipped with Super
Speed Dialing capability. Once information is stored in these locations, Super Speed Dialing allows you to place a call without pressing R.
The number dialed will not display for review.
NOTE Do not attempt the sequence 0, S. This will place a call to the local operator.
Turbo Dial
Press and hold for one second any one of the digit buttons 2 through 9 .
The digit buttons 2 through 9 (1 is reserved for Priority Dialing) provide an advanced form of
Super Speed Dialing. Once numbers have been stored in memory locations 2-9, calls can be placed from these locations by pressing the
31
739K01 3/9/0 10:02 AM Page 32
Memory associated key and holding for approximately one second. There is no need to press S.
NOTE Turbo Dialing is affected by "Call
Restriction" Service Levels 1, 2, and 3. See
"Change Service Level" found on page 52. Do not select these service levels if you wish to use
Turbo Dialing.
One-Touch Dialing Keys
Your phone has three special dialing keys, A,
B, D, which allow for easy one touch access to numbers stored in these locations.
To store a number:
1. Enter phone number to be stored.
2. Press s .
3. Press specific one touch key.
4. The phone is automatically in Alpha Entry
Mode. Enter a name or bypass by pressing s .
Phone will confirm storage by displaying Stored.
To place a call:
1. Press and hold the One-Touch Dial Key A ,
B , or D .
These keys function like Turbo Dial keys. When you press and hold A, B, or D, a call is placed to the number stored in that position. To recall the number, press R, and the specific
One-Touch Key. To clear the number, press C, s, and the specific One-Touch Key. ALPHA – will display. Press s. The unit will display the name and number along with the prompt CHANGE?.
Press s to clear both name and number.
32
Memory
STORED will display to indicate that the number has been cleared.
One-Touch Priority Dialing
When Priority Call is activated on your cellular phone you can use this feature to call an important number you have stored in memory location 01 even if the phone is locked.
At any time if you dial 911 or an emergency number previously stored by your cellular service provider, the display will read " Dialing Emrgcy."
If the unit is locked and you press and hold the 1 or enter an emergency number, the phone will still display " Locked" but will place the emergency call.
If you have stored an alternate non-emergency number in memory location 01, such as your home phone number, and use the turbo dial feature the phone will display " Priority Call."
Please keep in mind:
• Your emergency or priority number must be stored in memory location 01 to be able to place a call when the unit is locked. Be careful not to overwrite the number stored in this location.
• Some cellular systems have their own emergency numbers and do not allow access to numbers such as 911. Check with your cellular service provider for details about emergency calling in your area.
Scratch Pad Memory
The scratch pad permits entry of numbers from the keypad during conversation.
33
739K01 3/9/0 10:02 AM Page 34
Memory
If your party gives you another number to call, simply enter this from the keypad. If you make an error, press C to erase the last digit entered or hold C to erase the entire entry.
Advise your party that they will hear tones as you store the number. To call the scratch pad number at the end of an ongoing conversation, press E, S.
NOTE Refer to "Silent Scratch Pad" on page 45 for details on silencing the tones.
Tone Dialing (Two-Part Calling)
Your telephone provides the standard Dual Tone
Multi-Frequency (DTMF) signals typically used to access alternate long distance services, signal pagers, answering machines, etc. Generally, these services use a two-part procedure: First, a call is placed from the memory or through the keypad to a central telephone number.Then a secondary dial tone is heard, and the additional tone digits are sent.
To tone dial from the keypad
Enter the desired number and press S .
Append additional digits using the keypad once prompted. The tones are automatically sent as you press the keys. Do not press S again.
EXCEPTION If you have selected silent scratch pad, you must press R, s after entering the additional digits.
To tone dial from a memory location, recall from memory the number you wish to send using R, location number. Then press S. To send additional groups of numbers recall the location number and press R, S. Repeat as needed.
34
Memory
Two-part calling can be automated by a unique feature which permits the programming and pauses between groups of numbers. When recalled or sent, the telephone stops transmitting at the pause and waits for your response (i.e., secondary dial tone).
Pause Dialing (Memory Linking)
1. Enter the first group of numbers from the keypad or recall them from memory using
R .
2. Insert a pause by pressing F , S . insert paus ø will appear.
Press s and a ø will display where the pause in inserted.
3. Enter the next group of numbers, or recall them from memory by pressing F , R , two-digit location number.
4. Repeat this sequence for as many groups as you wish up to a maximum of 32 digits.
(Each pause occupies a digit.)
EXAMPLE To construct a number sequence which you might use to inquire about your bank balance, follow this example. The entry sequence required by the bank is to call the access number, wait for the tone, enter your ID number followed by #, wait for the tone, then enter your account number followed by #.
The bank’s telephone number is 123-4567. Your
ID number is 888. Your account number is 22.
35
739K01 3/9/0 10:02 AM Page 36
Memory
Instruction and
Key Sequence
1 Enter the phone number of the bank —
1, 2
,
3
,
4
,
5
,
6
,
7
or recall it from memory location xx — R , x, x
2 Create a pause —
F , S , s
3 Enter the ID number and a pound sign — 8 , 8 8 , # or recall it from memory location xx —
F
,
R
, x, x
4 Create another pause —
F
,
S
, s
5 Enter the account number and a pound sign —
2
,
2
,
#
6 To store number, press s and the Memory Location or One
Touch Key. Press s again to bypass Alpha display. The memory location number will be displayed to confirm storage. If you stored the number in a One Touch
Dial location, STORED will be displayed to confirm storage.
Display
1234567
234567ø
67ø888C
7ø888Cø
88Cø22C
–
ALPHA
To place a linked call, press S to transmit the first group of numbers, prior to the first pause. (If your number is stored in a One-Touch Dialing Key or a Turbo Dial location, simply press the key.) After waiting for the system response, press R, S to
36
Memory send the second group of numbers. Continue to press R, S until all digit groups are sent.
If the PIN code feature is activated the PIN code will automatically be sent after the first pause by pressing S.
NOTE Do not add the PIN code to the linked sequence. Your phone will automatically insert the
PIN code when placing a linked call. Follow the instructions in "PIN Code Activation" on page 46.
Edit a Memory Location
1. Press R and the two-digit location number.
2. Press R again, if name only displays, so that the phone number to be changed is displayed.
3. Edit phone number by pressing C to back out the digits to be changed. Enter new digits.
4. Press s and the same two-digit location number.
The display will flash ALPHA and then the name you have stored or – if no name is stored.
5. Change or add alpha name tag if desired. To edit name, press C to back out the letters to be changed. Enter new alpha characters.
(Enter alphabetic characters as described on page 28.)
6. Press s .
37
739K01 3/9/0 10:02 AM Page 38
Memory
8. You will see a Memory Protect message; press s to overwrite.
Memory location number will display as confirmation.
NOTE See "Number Preference" on page 41 for more details on step 2.
Clear Memory Entries
1. Press C , s , and the two-digit location number to be cleared.
2. The phone will display ALPHA – . Press s to bypass.
The phone will display Full, flash number in memory, followed by Change?.
3. Press s to clear.
or
Press E to exit without deleting the entry.
38
Features
Additional features that may be available with your phone but are not accessed through the feature menu, are also described in this section.
Select/Cancel Menu Features
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until the desired feature displays.
3. Press s to toggle the feature on, and C to toggle it off.
4. Press E to exit the Feature Menu.
EXAMPLE To activate silent keypad, press F,
1, and scroll with # or G until the display shows
KEYPAD TONE ON. Press s to activate this feature.
The display will then show KEYPAD TONEOFF.
Press E to exit the menu.
Signal Strength Meter (SSM)
To Disable the SSM from Displaying
1. Press F , 1 .
2. Scroll the menu by pressing H or G until
SIGNAL MTR ON displays.
3. Press C once to disable the SSM and s to reactivate.
4. Press E to exit the Feature Menu.
Once the SSM is disabled, on will appear in place of the s – – = = ≠ ≠
See "Signal Strength Meter" on page 22 for more details.
39
739K01 3/9/0 10:02 AM Page 40
Features
Feature Status Review
To Review Status
1. Press F , 0 , 9 , R .
2. Press G or H to scroll through activated features.
To End Review
Press
E
.
Status review permits you to scroll through your operating settings for your reference.
Listed on the page 59 are the status messages you may see if any advanced features are selected or changed from their standard setting.
Battery Indicator
If your cellular telephone is being used in a carry phone configuration,
Press F , 4 to display a battery indicator.
This allows you to review the battery charge level.
The battery indicator is displayed as a bar graph.
The B alone represents the lowest voltage with each additional bar representing a stronger charge.
B ––==≠≠
NOTE In the carry phone configuration, the display will go blank after six seconds. You may reactivate the display by pressing any key except P.
40
Features
Extended Talk Time
The extended talk time feature allows you to conserve battery power when operating in a strong signal area. To enable this feature, refer to "Feature
Menu" on page 39.
Microphone Muting
To mute microphone while in a call:
Press F , 6 .
To disable mute while in a call:
Press F , 6 again.
This feature allows you to confer privately with others in the car during a call. It will disable the microphone and display Mute. Note that M for
Mute appears on 6. The mute feature is canceled if you end your call.
Number Preference
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
Number PREFOFF displays.
3. Press s once to toggle this feature on, and C to toggle it off.
4. To exit the Feature Menu, press E .
The Number Preference feature reverses the display order of memory entries so that the number will be displayed before the name.
41
739K01 3/9/0 10:02 AM Page 42
Features
Automatic Answer
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
AUTO ANSROFF displays.
3. Press s once to toggle this feature on, and
C to toggle it off.
4. To exit the Feature Menu, press E .
This feature permits you to answer calls without pressing S. When your phone receives a call, it will ring twice, then answer the call.
NOTE We suggest that you do not select the
Automatic Answer and Silent Ringer simultaneously since incoming calls will then be announced only by the flashing Call in the display. Also, this feature may be incompatible with certain enhanced system services, such as no-answer transfer. Consult your
Cellular Service Provider.
Multiple Key Answer
1. Press F ,
1
.
2. Scroll the menu by pressing
H or
G until
MULTKEY ANSROFF displays.
3. Press s once to toggle this feature on, and C to toggle it off.
4. To exit the Feature Menu, press E .
The Multiple Key Answer feature allows you to answer an incoming call by pressing S or any digit key 1 though 9.
42
Features
Incoming Call Screening
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
CALL RCV ON displays.
3. Press s once to toggle this feature on and
C to toggle it off.
4. To exit the Feature Menu, press E .
Use this feature if you prefer not to receive incoming calls but wish to be informed of the attempt.
When the phone is on and this feature is selected, incoming calls are signaled by several short bursts of tone, Call in the display, and the black on indicator. The caller will receive the "Not in
Service" recording.
As a reminder that incoming call screening is selected, the unit will sound the special tone burst each time it is turned on.
NOTE We suggest you do not select Incoming
Call Screening and Silent Ringer simultaneously, since the incoming call will not be signalled by a short burst of tone.
Silent Ringer
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
RINGER ON displays.
3. Press s once to toggle this feature on, and C to toggle it off
4. To exit the Feature Menu, press E .
43
739K01 3/9/0 10:02 AM Page 44
Features
The telephone’s ring tones may be silenced where they could prove a distraction, as during a business conference, etc. In this case, incoming calls are announced only by a flashing Call in the display.
NOTE We suggest you do not select the Silent
Ringer and Automatic Answer simultaneously, since the phone will then answer a call without audible indication.
Distinctive Ringer
This feature allows you to select one of nine different ringer styles to differentiate when your phone is ringing. When selected, the phone will give you a brief sample of that ringer style.
1. Press F ,
1
.
2. Scroll the menu by pressing
H or
G until
Ringer Style displays.
3. Press s once to select this feature.
The selected ringer will sound as an example of this ringer style. The ringer style will display
Select 1-9.
4. Press
1
- 9 to sample the different ringer styles.
The display will show the number of the selected ringer style.
5. Press s to select the desired ringer style.
The display will show: Ringer X Set where the X is the number of the ringer style selected.
6. Press E to exit the menu.
44
Features
Silent Keypad
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until KEYPAD TONEOn displays.
3. Press s once to toggle this feature on, and
C to toggle this feature off.
4. To exit the Feature Menu, press E .
When selected, this feature silences the tones used to indicate keypad depressions.
Silent Scratch Pad
1. Press
F
,
1
.
2. Scroll the menu by pressing H or G until
SCRPAD TONE ON displays.
3. Press s once to toggle this feature on, and C to toggle this feature off.
4. To exit the Feature Menu, press
E
.
Use this feature to enter scratch pad numbers during a call without transmitting tones. You will hear the tones, but your called party will not.
NOTE Should you wish to transmit DTMF tones
(to access answering machines, pagers, automatic menus, etc.) while Silent Scratch Pad is activated, enter the digits and press R, S.
45
739K01 3/9/0 10:02 AM Page 46
Features
PIN Code Activation
Activate PIN Code
1. Press F ,
1
.
2. Scroll the menu by pressing
H or
G until
PIN INACTIV displays.
3. Press s once to toggle this feature on, and C to toggle it off.
4. To exit the Feature Menu, press E .
Store PIN Code in Memory Location 07
1. Enter PIN code.
2. Press s .
3. Press 0 , 7 .
Place a Call With PIN Code Active
1. Enter number to be called, or recall from memory.
2. Press S . Wait for double tone –“beep, beep.”
3. Press S . The phone will automatically send the PIN code stored in memory location 07.
Your cellular carrier may require a personal identification number (PIN) when placing outbound calls. This code assures the cellular system that the person placing the call is an authorized user.
Ask your cellular service provider if this is required in your system. Only select this feature if your cellular service provider requires it.
This feature will allow you to automatically send your PIN code with all outbound calls. If Invalid
PIN displays, check to see if you have activated the feature in the menu without storing a PIN
46
Features number in memory location 7. The PIN code must be less than seven digits.
If you enter a service area which does not require a
PIN code, disable the feature in the feature menu.
Timers
Call timers provide a useful means of monitoring the air-time spent in conversation. Several of these operate in the background and can be displayed at any time. Another offers beep tones heard only on your side of the conversation.
Each timer begins counting as a cellular channel is assigned, or when the phone rings to signal an incoming call. If an incoming call is not answered, the timers revert to their previous values.
Individual Call Timer
To Display the Time of Your Last Call
Press R , # , # .
This timer accumulates the air-time of a call in minutes and seconds.
It automatically resets before a new call is placed and when the phone is turned off.
Resettable Call Timer
To Display
Press R , # , # , # .
To Reset
Press F , 0 , 7 , C .
47
739K01 3/9/0 10:02 AM Page 48
Features
This timer accumulates the air-time in minutes from the point at which it is reset.
This resettable timer is generally utilized to track monthly air-time usage and is set in conjunction with the monthly billing cycle.
NOTE If you have two phone numbers programmed in your phone, each phone number has its own resettable call timer. To view the resettable call timer associated with the other phone number, switch your phone to that number, then use the sequence on the previous page.
Cumulative Call Timer
To Display
Press R , # , # , # , # .
This is a non-resettable timer which accumulates the phone’s total air-time in minutes, starting with the initial factory setting.
NOTE If you have two phone numbers programmed in your phone, each phone number has its own cumulative call timer. To view the cumulative call timer associated with the other phone number, switch your phone to that number, then use the sequence above.
Individual Display Timer
1. Press F , 1 .
2. Scroll the menu by pressing H or G until
INDIV TIMR OFF displays.
3. Press s once to toggle this feature on, and C to toggle it off.
48
Features
4. To exit the Feature Menu, press E .
This feature automatically displays the accumulated time in minutes and seconds during and after each call.
One-Minute Timer
1. Press F ,
1
.
2. Scroll the menu by pressing H or G until
ONE MIN TIMROFF displays.
3. Press s once to toggle this feature on, and C to toggle it off.
4. To exit the Feature Menu, press E .
This timer provides a tone ten seconds before the end of each minute during calls.
Security Features
Your telephone offers several forms of security against unauthorized use. These require either your three-digit unlock code, or the six-digit security code. The factory programmed unlock code is 123 and the factory programmed security code is 000000.
Electronic Lock
To Lock
1. Press F , and hold 5 until Lock?
displays.
2. Press s to lock. Locked will display.
To Unlock
Enter your three-digit unlock code. If you make an error, press C and start again.
49
739K01 3/9/0 10:02 AM Page 50
Features
The electronic lock prevents use of the telephone by disabling both incoming and outgoing calls. To help remember which key to use, note that L for
Lock appears on 5.
If a call is received during this period, the phone will ring, and you must enter the unlock code before the call can be answered.
Change Unlock Code
1. Press F , 0 .
2. Enter your six-digit security code.
3. Enter the new desired three-digit unlock code.
4. Press s . The new unlock code will display to confirm storage.
Display Unlock Code
1. Press F , 0 .
2. Enter your six-digit security code.
3. Press R . The phone will display Loc and the three-digit unlock code.
NOTE Use this procedure if you have forgotten your current three-digit unlock code.
Automatic Lock
1. Press F ,
1
.
2. Scroll the menu by pressing G or H until
AUTO LOCKOFF displays.
3. Press s once to toggle this feature on, and C to toggle it off.
4. To exit the Feature Menu, press E .
This feature automatically locks your phone each time it is turned off.
50
Features
Language Selection
1. Press F ,
1
.
2. Scroll through menu by pressing (insert up and down arrows) until Languag Select displays.
3. Press s once to select this feature.
4. Use the
G or
H arrows to scroll through the selections.
5. Press s to select the language of your choice.
6. Press E to exit the feature menu.
This feature allows you to select in which language (English, Spanigh, French or
Portuguese) your phone will display messages and prompts.
Auxiliary Alert
(mobile configurations only)
1. Press F , 4 with the unit on, unlocked, and Silent Ringer inactive.
ALERT will display.
2. Turn off the vehicle ignition.
The Auxiliary Alert feature allows an additional alerting device (horn or lights) to be activated for the first five rings (20 seconds) of an incoming call. This is useful if you intend to be outside of the vehicle and expect a call.
NOTE A call cannot be in progress when you enable Auxiliary Alert. Auto Answer is disabled during Auxiliary Alert.
When the Auxiliary Alert mode is enabled, the mobile telephone remains on despite the vehicle
51
739K01 3/9/0 10:02 AM Page 52
Features ignition being turned off. Calls may be placed while in the Auxiliary Alert mode unless the unit has also been locked subsequent to pressing F
,
4. The
Auxiliary Alert mode is automatically disabled the next time the ignition is turned from off to on. The
Auxiliary Alert mode can also be disabled by pressing P or by pressing F
,
4 again.
ALERT will turn off when the feature is disabled.
Change Service Level
1. Press F , 0 .
2. Enter your six-digit security code.
3. Enter the number of the service level you wish to use.
4. Press s .
The phone will display Level and the number selected.
Your telephone can be set to restrict call placement (as when lending the phone to another person). Using the six-digit security code, you may select one of the levels of restriction shown on the page 53.
52
Features
Restrictions
No restrictions (Standard setting)
• Full keypad and directory dialing
• No storage in directory locations
1-10 or One Touch Dial locations
• Keypad dialing only
• No directory or Turbo Dial access
Phone will place calls from all directory locations (
R
,
0 1
-
9 9
,
S
).
No keypad dialing. No directory change or storage.
Seven-digit (local) dialing only, including directory and message calls
(if seven digits or less)
Phone will place calls only from directory locations 1-10 (
R
,
0 1
-
1 0
,
S
).
If locations 1-10 are cleared, no outgoing calls can be made. No keypad dialing. No directory or One Touch Dial storage.
Level
4
6
3
2
5
1
To change the phone to unrestricted operation, use the procedure above and enter service level 4.
Master Reset
CAUTION Once begun, this procedure cannot be canceled or reversed.
1. Press F , 0 .
2. Enter your six-digit security code twice.
3. Press
1
, s
.
53
739K01 3/9/0 10:02 AM Page 54
Features
This feature allows you to reset most or all the user selectable options to their standard settings.
Master reset will perform the functions listed below.
Master Reset will Perform these Functions
Cancel Automatic Hands Free
Cancel Automatic Answer
Cancel Individual Display Timer
Cancel Automatic Lock
Cancel Incoming Call Screening
Cancel Multiple Key Answer
Cancel Number Preference Feature
Cancel One-Minute Timer
Cancel Silent Scratch Pad
Reinstate Emergency Message
Reinstate Keypad Tones
Reinstate Signal Strength Meter
Reinstate Ringer Tones
Reinstate Turbo Dialing
Reset Service Level to Level #4
(Standard setting)
Return System Type to Standard
Cancel PIN Activation
Pg.
45
39
43
31
49
45
33
52
59
46
21
42
48
50
43
42
41
Features
Master Clear
CAUTION Master Clear performs all the functions of Master Reset, in addition to erasing all names and numbers stored in memory, and clearing the
Resettable Call Timer. Once begun, this procedure cannot be canceled or reversed.
1. Press F , 0 .
2. Enter your six-digit security code twice.
3. Press 9 , s .
Busy may display.
4. Wait for this to clear before using the phone. It may take several minutes, depending on how full your memory is.
Do not turn the phone off during this operation.
54 55
739K01 3/9/0 10:02 AM Page 56
Reference
The Cellular System
There are generally two types of cellular systems serving any metropolitan area. One of these will most likely be operated by the telephone company that provides telephone service to your community, generally referred to as a wireline carrier. The other cellular service provider is a radio common carrier, referred to as a non-wireline carrier.
Your Cellular Service Operator will provide information concerning specific features, procedures, and coverage in your particular area.
Service Area
The area within which the telephone operates is defined by your cellular service provider. Since this is a radio system, no exact boundaries (as on a map) can be drawn. The black N Svvcc (No
Service) lights if you are beyond range of a service area. There may be locations within your area, such as tunnels and underground parking facilities, where the phone may act as if it were beyond range.
Weak Signal Alert
If you are called while in a location the system determines is inadequate for high quality service, you may hear a series of beeps to inform you of the call attempt. The caller will receive the recorded "not in service" message, Call will display, and the black on indicator will flash quickly. If this occurs, you must press C before the phone will operate. Most systems do not impose air-time charges for such call attempts.
56
Reference
Switchhook and Enhanced
System Services
Press
S
.
During a call, pressing S performs a switchhook function used to access enhanced Cellular System features, such as call waiting and conference calls. For the functioning of these features with
S, consult your Cellular Service Provider.
Roaming
The term Roaming applies to the use of cellular telephones within systems other than those designated as their Home system. R oa whenever the phone comes within range of a visited system. As your phone begins to roam, it seeks service according to the conditions you have selected. See "System Type Selection" on page 59.
Steady illumination of Roam signals that your phone is accessing a home type system, while flashing indicates the phone is attempting connection through a non-home type system.
Contact your system operator, or that of the visited system, for information on dialing and billing procedures.
Selectable System Registration
To Review Current Setting
1. Press R , * . The display will show the current active system choice.
2. Press E to exit without changing selection.
739K01 3/9/0 10:02 AM Page 58
Reference
To Select
1. Press R , * . The display will show the current active system choice.
2. Repeatedly press * to review the system type modes. (Press E to exit without changing selections.)
3. Press s to activate the displayed selection.
4. Press
E to exit.
System Type Selection
Your telephone seeks cellular service according to the mode you have selected. If you have selected two-system operation, the phone seeks cellular service according to the system type mode selected for each phone number.
Constant flashing of R oa m, or a steadily lit N Svvcc while within your home service area may indicate an unintentional choice has been made. If this occurs, re-enter system type selection to see if the unit is operating in standard mode, or if an alternate selection has been made.
Reference
System Type Selection
Standard Mode
Your phone first seeks a home type system, then a non-home type.
If home system is type A
If home system is type B
Invert Preference Mode
Your phone first seeks a non-home type system, then home type. (Select this mode if in a fringe area of your home system or in certain roaming situations.)
If home system is type A
Fast flashing Roam = call on B system
Slow flashing Roam = call on home type system
Slow flashing In Use = call on home system
If home system is type B
Fast flashing Roam = call on A system
Slow flashing Roam = call on home type system
Slow flashing In Use = call on home system
Home Only Mode
Phone will not operate outside its home system.
Scan A Mode
Phone will operate only within A systems.
Scan B Mode
will operate only within B systems.
Preferred Scanning Mode
Unit will operate only within specifically identified systems. This choice requires entry of up to 60 System ID numbers for those systems over which you wish to operate. The
SID digits are entered as obtained from your
Cellular Service Operator.
Std A B
Std B A
Scan B A
Scan A B
Home
Scan A
Scan B
PSCAN
739K01 3/9/0 10:02 AM Page 60
Reference
Preferred SID’s
To enter Preferred SID’s:
1. Press R , * .
2. Press * or # to scroll to pscan
3. Press s to enter first 5 digit System ID
( 40000 will display as the default).
4. Press # to enter each SID until all desired
SID’s are entered (up to 60).
5. Press s to store your entries.
Reference
Troubleshooting
1. Is the unit locked?
See "Electronic Lock", page 49.
2. Is the No Svc (No Service) indicator lit?
See "Status Indicators", page 16.
3. Is your Roam Indicator lit?
Constant flashing of the R oa in your home service area may indicate that an incompatible system type has been selected.
See "Roaming", page 59.
4. Are you having difficulty accessing devices such as answering machines which require longer access tones?
Check to see if Silent Scratchpad is enabled. If so, disable through the Feature Menu, as described in "Select/Cancel Menu Features" on page 39, and try the call again.
739K01 3/9/0 10:02 AM Page 62
Reference
Quick Reference Feature Guide
Basic Operation
Turn It On P.
Lock F, 5.
Unlock Three-digit unlock code.
Turn It Off P.
Place a Call Enter number, S.
Receive a Call S, or lift handset to ear.
End Call E, or return handset to its mount.
Volume Control
Earpiece Lift handset, G or H.
Speaker With handset mounted, press and hold G or H.
Ringer F, then G or H.
Store to Memory
Number and Phone number, s,
Name two-digit location, alpha characters, s. To store in next available location, s, *.
Memory Recall
By Location R, two-digit location. S to place call.
Super Speed Memory location, S.
Dialing
Turbo Dialing Press and hold memory location ( 19) for one second.
Reference
Feature Menu
Enter Menu F, 1. H or G to scroll.
Select Feature C.
Cancel Feature C.
Exit E.
Additional
Features
Status Review F, 0, 9, R. H or
G to scroll.
Last Number R, S.
Recall
Display Own R, #.
Number
Activate Other R, #, s.
Number
Mute Microphone F, 6.
Scratch Pad Enter numbers during call.
E to terminate call and
S to place call to scratch pad number.
63
739K01 3/9/0 10:02 AM Page 64
Reference
’
A
A1
A2
ALPHA
B––==≠≠
B1
B2
Message Glossary
BUSY
C
CALL
CHANGE?
Clear?
(Apostrophe) Scrolling activated
* displayed as “A”
Two-System Operation (Active system is non-wireline, using phone number 1.)
Two-System Operation (Active system is non-wireline, using phone number 2.)
Alpha Entry is selected.
Battery Voltage Meter (Number of bars indicates relative level of voltage.)
Two System Operation (Active system is wireline, using phone number 1.)
Two System Operation (Active system is wireline, using phone number 2.)
Master Clear functioning
Precedes Cumulative Timer display
(also used to display #)
Shows incoming call (also used to indicate call in absence)
Used when memory protect is activated to prevent accidental overwriting of a memory location
Memory Protect is activated to prevent accidental overwriting of a memory location.
EMPTY
FULL
HOME
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
LEVEL 5
LEVEL 6
LOC
LOCKED
MUTE
ON
PRIORITY
R
REDIAL
S––==≠≠
SCAN A
SCAN AB
SCAN B
SCAN BA
Reference
Name Directory is empty.
Indicates all directory locations are full, requested block is unavailable, or location has a number already stored in it
System Type Selection – Home
Mode
Service level selected
Service level selected
Service level selected
Service level selected
Service level selected
Service level selected
Precedes unlock code when displayed
Unit is locked.
Microphone is muted.
Telephone is on.
Priority Call is active.
Precedes display of Resettable
Timer
Automatic Redial is selected.
Signal Strength Meter (SSM)
(Number of bars indicates relative signal strength.)
System Type Selection (scan “A” only)
System Type Selection (scan “A” type first, then “B”)
System Type Selection (scan “B” only)
System Type Selection (scan “B” type first, then “A”)
739K01 3/9/0 10:02 AM Page 66
Reference
STD
STD AB
All user features set to standard
System Type Selection (nonwireline standard mode)
STD BA System Type Selection (wireline standard mode)
System Busy Cellular system is busy.
V––==≠≠ Volume Meter (Number of bars indicates relative volume level.)
Reference
Index
Automatic Answer ................................................42
Automatic Hands Free .........................................21
Automatic Lock ....................................................50
Automatic Redial..................................................18
Auxiliary Alert .......................................................51
Battery Indicator...................................................40
Call in Absence Indicator.....................................19
Cancel Menu Features ........................................39
Change Service Level..........................................53
Change Unlock Code...........................................50
Clear Memory Entries ..........................................38
Cumulative Call Timer .........................................48
Display Own Phone Number ...............................24
Display Unlock Code ...........................................50
Distinctive Ringer .................................................44
Earpiece Volume .................................................23
Edit Memory Location ..........................................37
Electronic Lock ....................................................49
End a Call ............................................................19
Enhanced Simplex Hands Free ...........................21
Extended Talk Time.............................................41
Feature Status Review ........................................40
General Safety Information...............................6-10
Hands Free Operation (with optional HF Microphone) .....................................20
Incoming Call Screening......................................43
Individual Call Timer ............................................47
Individual Display Timer.......................................47
Introduction ..........................................................11
Last Number Recall .............................................30
Manual Handset to Hands Free Operation..........20
Master Clear ........................................................55
739K01 3/9/0 10:02 AM Page 68
Reference
Master Reset .......................................................53
Memory Autoload.................................................27
Memory Linking ...................................................35
Memory Protect ...................................................29
Message Glossary ...............................................64
Microphone Muting ..............................................41
Multiple Key Answer ............................................42
Name Preference.................................................41
One Minute Timer ................................................49
One-Touch Dialing Keys......................................32
One-Touch Priority Dialing...................................33
Patent Information ...............................................78
Pause Dialing.......................................................35
Phone Overview ..................................................12
PIN Code Activation.............................................46
Place a Call..........................................................17
Place a Hands Free Call......................................20
Preferred SID’s ....................................................60
Quick Reference Feature Guide ..........................62
Recalling by Location Number.............................29
Recalling from Memory........................................29
Recalling Last 10 Numbers Dialed ......................30
Receive a Call......................................................19
Receive a Hands Free Call..................................20
Resettable Call Timer ..........................................47
Ringer Volume .....................................................24
Roaming...............................................................57
Scratch Pad Memory ...........................................33
Scrolling by Location Number..............................29
Scrolling from Memory.........................................29
Security Features.................................................49
Select Menu Features..........................................39
Selectable System Registration...........................57
Reference
Selecting a Memory Location ..............................26
Service Area ........................................................56
Signal Strength Meter ....................................22, 39
Silent Keypad.......................................................45
Silent Ringer ........................................................43
Silent Scratch Pad ...............................................45
Speaker Volume ..................................................23
Store to a Location Number.................................26
Storing a Phone Number and a Name ................27
Storing Information in Memory ............................26
Super Speed Dialing............................................31
Switch to Second Phone Number........................24
Switchhook and Enhanced System Services ......57
The Cellular System ............................................56
Timers ..................................................................47
Tone Dialing.........................................................34
Troubleshooting ...................................................61
Turbo Dial ............................................................31
Turn Phone On and Off .......................................15
Two-Part Calling ..................................................34
Volume Meter ......................................................22
Weak Signal Alert ................................................56
Welcome ................................................................4
739K01 3/9/0 10:02 AM Page 70
Reference
C
Th en e U
C on
S.. F oo d a nd err U pd
Drru g A miin orr D evviicce d R ad n M ob e P ho attiio n''ss all H ea
FDA has been receiving inquiries about the safety of mobile phones, including cellular phones and PCS phones. The following summarizes what is known-and what remains unknown--about whether these products can pose a hazard to health, and what can be done to minimize any potential risk. This information may be used to respond to questions.
W hyy tth e cco errn ?
Mobile phones emit low levels of radiofrequency energy (i.e., radiofrequency radiation) in the microwave range while being used. They also emit very low levels of radiofrequency energy (RF), considered non-significant, when in the stand-by mode. It is well known that high levels of RF can produce biological damage through heating effects
(this is how your microwave oven is able to cook food). However, it is not known whether, to what extent, or through what mechanism, lower levels of
RF might cause adverse health effects as well.
Although some research has been done to address these questions, no clear picture of the biological effects of this type of radiation has emerged to date.
Thus, the available science does not allow us to conclude that mobile phones are absolutely safe, or that they are unsafe. However, the available scientific evidence does not demonstrate any adverse health effects associated with the use of mobile phones.
W ha dss o ho ess a n q ue ?
Questions have been raised about hand-held mobile phones, the kind that have a built-in antenna that is positioned close to the user's head during normal telephone conversation. These types of mobile phones are of concern because of the short distance between the phone's antenna--the primary source of
Reference the RF--and the person's head. The exposure to RF from mobile phones in which the antenna is located at greater distances from the user (on the outside of a car, for example) is drastically lower than that from hand-held phones, because a person's RF exposure decreases rapidly with distance from the source. The safety of so-called "cordless phones," which have a base unit connected to the telephone wiring in a house and which operate at far lower power levels and frequencies, has not been questioned.
H ow ucch evviid en e iiss tth erre att h nd d m ob ph on htt b e h
Briefly, there is not enough evidence to know for sure, either way; however, research efforts are ongoing. The existing scientific evidence is conflicting and many of the studies that have been done to date have suffered from flaws in their research methods.
Animal experiments investigating the effects of RF exposures characteristic of mobile phones have yielded conflicting results. A few animal studies, however, have suggested that low levels of RF could accelerate the development of cancer in laboratory animals. In one study, mice genetically altered to be predisposed to developing one type of cancer developed more than twice as many such cancers when they were exposed to RF energy compared to controls. There is much uncertainty among scientists about whether results obtained from animal studies apply to the use of mobile phones. First, it is uncertain how to apply the results obtained in rats and mice to humans. Second, many of the studies that showed increased tumor development used animals that had already been treated with cancercausing chemicals, and other studies exposed the animals to the RF virtually continuously--up to 22 hours per day.
739K01 3/9/0 10:02 AM Page 72
Reference
For the past five years in the United States, the mobile phone industry has supported research into the safety of mobile phones. This research has resulted in two findings in particular that merit additional study:
1. In a hospital-based, case-control study, researchers looked for an association between mobile phone use and either glioma (a type of brain cancer) or acoustic neuroma (a benign tumor of the nerve sheath). No statistically significant association was found between mobile phone use and acoustic neuroma. There was also no association between mobile phone use and gliomas when all types of types of gliomas were considered together. It should be noted that the average length of mobile phone exposure in this study was less than three years.
When 20 types of glioma were considered separately, however, an association was found between mobile phone use and one rare type of glioma, neuroepithelliomatous tumors. It is possible with multiple comparisons of the same sample that this association occurred by chance. Moreover, the risk did not increase with how often the mobile phone was used, or the length of the calls. In fact, the risk actually decreased with cumulative hours of mobile phone use.
Most cancer causing agents increase risk with increased exposure. An ongoing study of brain cancers by the National Cancer Institute is expected to bear on the accuracy and repeatability of these results.
1
2. Researchers conducted a large battery of laboratory tests to assess the effects of exposure to mobile phone RF on genetic material. These included tests for several kinds of abnormalities, including mutations, chromosomal aberrations,
DNA strand breaks, and structural changes in the
Reference genetic material of blood cells called lymphocytes.
None of the tests showed any effect of the RF except for the micronucleus assay, which detects structural effects on the genetic material. The cells in this assay showed changes after exposure to simulated cell phone radiation, but only after 24 hours of exposure. It is possible that exposing the test cells to radiation for this long resulted in heating. Since this assay is known to be sensitive to heating, heat alone could have caused the abnormalities to occur. The data already in the literature on the response of the micronucleus assay to RF are conflicting. Thus, follow-up research is necessary.
2
FDA is currently working with government, industry, and academic groups to ensure the proper follow-up to these industry-funded research findings.
Collaboration with the Cellular Telecommunications
Industry Association (CTIA) in particular is expected to lead to FDA providing research recommendations and scientific oversight of new CTIA-funded research based on such recommendations.
Two other studies of interest have been reported recently in the literature:
1. Two groups of 18 people were exposed to simulated mobile phone signals under laboratory conditions while they performed cognitive function tests. There were no changes in the subjects' ability to recall words, numbers, or pictures, or in their spatial memory, but they were able to make choices more quickly in one visual test when they were exposed to simulated mobile phone signals.
This was the only change noted among more than
20 variables compared.
3
2. In a study of 209 brain tumor cases and 425 matched controls, there was no increased risk of brain tumors associated with mobile phone use.
739K01 3/9/0 10:02 AM Page 74
Reference
When tumors did exist in certain locations, however, they were more likely to be on the side of the head where the mobile phone was used.
Because this occurred in only a small number of cases, the increased likelihood was too small to be statistically significant.
4
In summary, we do not have enough information at this point to assure the public that there are, or are not, any low incident health problems associated with use of mobile phones. FDA continues to work with all parties, including other federal agencies and industry, to assure that research is undertaken to provide the necessary answers to the outstanding questions about the safety of mobile phones.
W ha ow n a bo h avve ee n rre po d iin p ho ?
hu ha ma nd n cca elld err tth mo att e
Some people who have used mobile phones have been diagnosed with brain cancer. But it is important to understand that this type of cancer also occurs among people who have not used mobile phones. In fact, brain cancer occurs in the U.S. population at a rate of about 6 new cases per 100,000 people each year. At that rate, assuming 80 million users of mobile phones (a number increasing at a rate of about 1 million per month), about 4800 cases of brain cancer would be expected each year among those 80 million people, whether or not they used their phones.
Thus it is not possible to tell whether any individual's cancer arose because of the phone, or whether it would have happened anyway. A key question is whether the risk of getting a particular form of cancer is greater among people who use mobile phones than among the rest of the population. One way to answer that question is to compare the usage of mobile phones among people with brain cancer with the use of mobile phones among appropriately
Reference matched people without brain cancer. This is called a case-control study. The current case-control study of brain cancers by the National Cancer Institute, as well as the follow-up research to be sponsored by industry, will begin to generate this type of information.
W ha DA e cco ncce g tth e ssa off m ob p ho ?
Under the law, FDA does not review the safety of radiation-emitting consumer products such as mobile phones before marketing, as it does with new drugs or medical devices. However, the agency has authority to take action if mobile phones are shown to emit radiation at a level that is hazardous to the user.
In such a case, FDA could require the manufacturers of mobile phones to notify users of the health hazard and to repair, replace or recall the phones so that the hazard no longer exists.
Although the existing scientific data do not justify
FDA regulatory actions at this time, FDA has urged the mobile phone industry to take a number of steps to assure public safety. The agency has recommended that the industry:
• support needed research into possible biological effects of RF of the type emitted by mobile phones;
• design mobile phones in a way that minimizes any
RF exposure to the user that is not necessary for device function; and
• cooperate in providing mobile phone users with the best possible information on what is known about possible effects of mobile phone use on human health.
At the same time, FDA belongs to an interagency working group of the federal agencies that have responsibility for different aspects of mobile phone safety to ensure a coordinated effort at the federal level. These agencies are:
739K01 3/9/0 10:02 AM Page 76
Reference
• National Institute for Occupational Safety and
Health
• Environmental Protection Agency
• Federal Communications Commission
• Occupational Health and Safety Administration
• National Telecommunications and Information
Administration
The National Institutes of Health also participates in this group.
e a bsse p ossssiib e rriisskk,, w ha n cco orrm attiio n a bo utt a nyy errn ed diivviid allss d ?
If there is a risk from these products--and at this point we do not know that there is--it is probably very small. But if people are concerned about avoiding even potential risks, there are simple steps they can take to do so. For example, time is a key factor in how much exposure a person receives. Those persons who spend long periods of time on their hand-held mobile phones could consider holding lengthy conversations on conventional phones and reserving the hand-held models for shorter conversations or for situations when other types of phones are not available.
People who must conduct extended conversations in their cars every day could switch to a type of mobile phone that places more distance between their bodies and the source of the RF, since the exposure level drops off dramatically with distance. For example, they could switch to:
• a mobile phone in which the antenna is located outside the vehicle,
• a hand-held phone with a built-in antenna connected to a different antenna mounted on the outside of the car or built into a separate package, or
7 6
• a headset with a remote antenna to a mobile phone carried at the waist.
Again, the scientific data do not demonstrate that mobile phones are harmful. But if people are concerned about the radiofrequency energy from these products, taking the simple precautions outlined above can reduce any possible risk.
W he e cca n II ffiin d a diittiio na orrm attiio ?
For additional information, see the following websites:
F ed all C om un nss C om
Safety Program (select "Information on Human
Exposure to RF Fields from Cellular and PCS Radio
Transmitters"): http://www.fcc.gov/oet/rfsafety
W orrlld ea Orrg an
Commission on Non-Ionizing Radiation Protection
(select Qs & As): http://www.who.int/emf eccttiio n U niitte
B oa
Kiin gd m,, N attiio na ad ollo giicca
C ellllu arr T elle om mu attiio nss IIn
(CTIA): http://www.wow-com.com
ussttrryy A
S.. F oo d a nd g A dm
Devices and Radiological Health: http://www.fda.gov/cdrh/consumer/
1
Muscat et al. Epidemiological Study of Cellular Telephone Use and Malignant
Brain Tumors. In: State of the Science Symposium;1999 June 20; Long Beach,
California.
2
Tice et al. Tests of mobile phone signals for activity in genotoxicity and other laboratory assays. In: Annual Meeting of the Environmental Mutagen Society;
March 29, 1999, Washington, D.C.; and personal communication, unpublished results.
3 Preece, AW, Iwi, G, Davies-Smith, A, Wesnes, K, Butler, S, Lim, E, and Varey, A.
Effect of a 915-MHz simulated mobile phone signal on cognitive function in man.
Int. J. Radiat. Biol., April 8, 1999.
4 Hardell, L, Nasman, A, Pahlson, A, Hallquist, A and Mild, KH. Use of cellular telephones and the risk for brain tumors: a case-control study. Int. J. Oncol., 15:
113-116, 1999.
7 7
739K01 3/9/0 10:02 AM Page 78
Reference
P atte orrm attiio
Manufactured under one or more of the following U.S. patents.
4523155
4546329
4550426
4551696
4564821
D282169
4571595
4573017
4574243
4585957
4602218
D284759
D285439
4616314
4617520
D286778
4626309
4628529
4629829
4630304
4630305
4633141
4636593
4636741
D288432
D270835
D271491
Re.31470
4431977
4434461
4455534
4462098
D275951
4484153
4485486
4486624
D276809
4491972
D277667
4504834
D278708
4121218
4138681
4193036
4254382
4302845
4312074
4327319
4329666
4369516
4369522
4378603
4390963
D269873
4398265
4400584
4400585
4741018
4741034
4742562
D295627
4746242
D295973
D295975
4751737
D296187
4761621
4764737
D297734
D297735
4777564
Re.32768
D299136
4797929
4798975
4800348
4802236
4809356
4811377
4811404
4827226
4827507
4706036
D292920
4710724
4711361
4715063
4716319
4716391
4723305
D294257
4727306
4727583
4730195
4734635
4736277
4737976
4740794
4648125
4649543
D288683
4654655
D289156
4662691
4667333
4668917
4670747
4672502
4680787
4681476
4683585
4692726
4704588
D292578
4972432
4972455
4975808
4984290
D314173
D315330
D315346
D315543
D315559
D315565
5004992
D315907
5008925
D316417
D316859
5017856
5018188
5020091
5020092
5020093
5028083
5028859
5029044
5029233
5031028
4904549
4905288
4905301
D306293
D306441
D306594
4912602
4918732
4922178
4945570
4954796
4959851
4963812
4963843
4965537
4972355
4829274
4837534
D301476
4843621
4845772
D302015
4851966
4868576
4870686
D303656
4876552
4879533
D305427
4896124
4897873
D305717
5150384
5152006
5157693
5163159
5164652
5166596
5175759
5175874
D332261
5182749
D332785
5185566
5187809
5193223
5195106
5195108
5201069
5204977
5210793
5214675
5222104
5222251
D337332
5230007
5230093
D325915
5113436
5117450
5121047
5122480
5122722
D327061
5128834
D328302
5142551
5142696
5146620
5148471
5148473
5148961
5150359
5036532
5053924
5057762
D320780
5059885
5060294
D322783
D322955
5081674
5083304
D324024
D324388
5095503
D325028
D325583
5109536
5363071
5365549
D352497
5366826
D353131
D353361
5375143
5375258
5379324
D354055
D354062
5384825
D356084
5402447
5406146
5406562
D357224
D357457
5410741
D357680
D357681
5428836
D359734
D359735
D359959
5263052
5276707
5278994
D343173
5280637
D344087
5287553
5287555
5287556
D344511
5301365
5321847
D348880
5349588
5359696
5361400
5233633
5235492
5237257
5239127
5241545
5241548
5241650
5241693
5242767
D339582
5249302
5251331
D340710
5260988
5261119
5262710
5511235
D369162
5513078
D369359
5519303
5519346
5524276
5524278
D370463
5530922
5542116
5544250
D372481
5546275
5546380
D372896
5551078
5559471
D374424
D374872
5572193
5574976
5577268
D375732
D375733
D365094
D365817
5486843
5487184
5488335
5488649
D366872
5493198
5493714
5497126
5497382
D367640
5499394
5506490
D368696
5510693
5432017
D360632
5438684
D361070
5442680
5446763
5448763
5448771
5453997
D362840
5457744
5459640
5463646
5465412
5469177
5475752
D375734
D375932
D375952
D376127
5588041
5589766
5590177
5594778
5594951
D377792
D377934
5604050
5606730
D378366
5613229
5613863
5615233
5621763
PAT111398
***Other patents pending
N ess::
Reference
739K01 3/9/0 10:02 AM Page 80
Reference Reference
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement