Kyocera FS-8000 C, CD, CN Color Printer Quick Reference Guide
KYOCERA FS-8000C is a versatile color printer designed for high-quality and efficient printing. With its advanced features, it caters to various printing needs, making it an ideal choice for both personal and professional use.
The FS-8000C boasts a remarkable print resolution of up to 1200 x 1200 dpi, delivering sharp and vibrant prints. It supports a wide range of paper sizes and types, including A4, A3, and envelopes, providing flexibility in your printing tasks.
This printer offers fast printing speeds, enabling you to quickly produce your documents. Its large paper capacity, with multiple paper cassettes and an optional paper feeder, ensures uninterrupted printing sessions.
โฆษณา
โฆษณา
Kyocera Corporation
14-9, Tamagawadai 2-Chome, Setagaya Ward
Tokyo 158-8610, Japan
FS-8000C
FS-8000CD
FS-8000CN
Color Printer
©2001 by Kyocera Corporation. All rights reserved. Revision 1.4., 2001.12
Printed in Japan
2BM80030D
Quick Reference Guide
FS8000QR.book Page 0 Tuesday, December 25, 2001 10:47 AM
Notice
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY
IMPROPER INSTALLATION OF THE PRODUCT.
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE
PRINTER’S NATIVE MODE OR ONE OF ITS EMULATION
MODES.
The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printer’s firmware (contents of its readonly memory).
This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this manual, any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done.
©2001 Kyocera Corporation. All rights reserved.
The names of actual companies and products mentioned herein may be the trademarks of their respective owners.
FS8000QR.book Page 1 Tuesday, December 25, 2001 10:47 AM
FS-8000C Quick
Reference Guide
FS8000QR.book Page 2 Tuesday, December 25, 2001 10:47 AM
Contents
Guide to the information about the printer .................................3
Understanding the Error Messages ...........................................4
Loading Paper .........................................................................11
Clearing Paper Jams ...............................................................14
[Paper Jam — Feeder # Cover] ..................................15
[Paper Jam — Cassette #] ..........................................15
[Paper Jam — MP Tray] .............................................16
[Paper Jam — Duplexer Drawer] ................................16
[Paper Jam — Paper Feed Unit] .................................17
[Paper Jam — Side Cover] .........................................22
[Paper Jam — Option Stacker] ...................................23
Toner Container Replacement ................................................24
Replacing the Toner Container ...................................25
Replacing the Waste Toner Bottle ..............................27
Replacing the Oil Unit ..............................................................29
Replacing the Maintenance Kit D (Separation Charger Unit) ..32
Cleaning the Printer .................................................................36
Cleaning the Paper Feed Unit .....................................36
Cleaning the Main Charger Unit ..................................38
2
FS8000QR.book Page 3 Tuesday, December 25, 2001 10:47 AM
Guide to the information about the printer
The following documentation and CD-ROM are supplied:
Quick Reference
Guide (This brochure)
Operation Guide
This manual provides common information about the printer such as loading paper, understanding messages, etc. This manual can be retained in the plastic pocket at the printer.
This guide is supplied as an online manual
(PDF) in the CD-ROM. This guide fully details the information on the printer features, hardware, troubleshooting, printer driver handling, etc.
Installation Guide
Kyocera Mita Digital
Library CD-ROM
This CD includes the printer software for
Kyocera Mita printers such as printer drivers, network printer monitors, and various software utilities.
Web site
This guide provides information on installing the printer and other options before starting to use.
The latest versions of printer drivers and utilities are available at: http://www.kyocera.com/w2k/.
3
FS8000QR.book Page 4 Tuesday, December 25, 2001 10:47 AM
Understanding the Error Messages
These messages appear on the printer’s message display when the printer needs the operator’s attention.
For more details, refer to chapter 6 of the Operation
Guide.
Message
Add paper
(with paper source indication)
Add staples
Press GO
Call service
####:0123456
Call service
F####:0123456
Call service
Person F0
Cassette 1 not loaded
Corrective Action
The paper has run out in the paper source
(paper cassettes, MP tray, or optional paper feeders). Supply paper according to the paper source displayed.
The optional document finisher has run out of staples. Replenish staples and press the GO key.
A mechanical error (#=0, 1, 2, ...). Contact your Kyocera Mita dealer for service. The printer does not operate when this message is displayed. The total number of pages printed is also indicated, e.g.
0123456.
A controller error. Contact your Kyocera
Mita dealer for service. The printer does not operate when this message is displayed.
A data communication error between the printer controller and the operator panel.
Contact your Kyocera Mita dealer for service. The printer does not operate when this message is displayed.
No. 1 (topmost) paper cassette is not installed. Install the cassette. The cassette number can be 1(topmost) to 6 (bottom), or, for the FS-8000CD, 2 to 6
(bottom).
4
FS8000QR.book Page 5 Tuesday, December 25, 2001 10:47 AM
Message
Check waste toner bottle
Clean printer
Press GO
Duplex drawer not loaded
Face-down tray paper full
Face-up tray path error
File not found
Press GO
Format error
Hard disk
Format error
Memory Card
Front cover open
Hard disk err ##
Press GO
I/F occupied
Corrective Action
The waster toner bottle is not installed or full. Install the waste toner bottle.
The printer has reached the schedule to conduct cleaning. Clean the inside of the printer. After cleaning the inside of the printer, press the GO key and the printer will resume printing.
This message is applicable to the FS-
8000CD only. The duplexer drawer is not installed. Install the duplexer drawer.
The face-down tray has become full
(approx. 500 pages). Remove all printed pages from the face-down tray.
The face-up tray is not open although you have attempted to print in the face-up tray.
Open the face-up tray.
You have attempted to print a job that is not contained in the virtual mailbox.
The hard disk installed in the printer is not formatted, and therefore cannot be read or written.
The memory card inserted in the printer is not formatted, and therefore cannot be read or written.
The front cover is open. Close the front cover.
A hard disk error has occurred. Press the
GO key to proceed.
You have attempted to use the operator panel to change a setting on the interface from which data are presently being received. Wait until the printer finishes printing jobs on the interface.
5
FS8000QR.book Page 6 Tuesday, December 25, 2001 10:47 AM
Install MK
[B]
Install MK
[C]
Install MK
[D]
Message
ID error
Insert the same memory card
Install MK
[A] or[A2]
Corrective Action
The user ID entered on the operator panel for a private job, or a stored job is not correct. Check the user ID that you specified on the printer driver.
This message is displayed when you accidentally removed the memory card while the printer is reading it and you inserted the wrong memory card after urged by the printer to replace the memory card
(Insert again). Remove the wrong memory card from the memory card slot and insert the correct memory card.
Replace Maintenance Kit A or A2 which is displayed on your printer message window. Depending on the printer you have purchased, the maintenance kit may be type A or type A2. Replacement of the maintenance kit requires professional servicing. Contact your Kyocera Mita dealer.
Replace Maintenance Kit B. Replacement of the maintenance kit requires professional servicing. Contact your Kyocera
Mita dealer.
Replace Maintenance Kit C. Replacement of the maintenance kit requires professional servicing. Contact your Kyocera
Mita dealer.
Replace Maintenance Kit D. Replacement of the maintenance kit requires professional servicing. Contact your Kyocera
Mita dealer.
Note: This message is not applicable for
European countries and Australia.
6
FS8000QR.book Page 7 Tuesday, December 25, 2001 10:47 AM
KPDL Error ##
Press GO
Load Cassette #
(paper size)/(paper type)
Load MP tray
(paper size)/(paper type)
Message
Memory card err
Insert again
MemoryCard err##
Press GO
Memory overflow
Press GO
Missing duplex unit
Missing stapler unit
Corrective Action
KPDL (PostScript) error has occurred.
Press the GO key to resume printing. Or, you can abandon printing by the CANCEL key.
The paper cassette (indicated by #) matching the paper size and paper type of the current job is empty. Load paper into the paper cassette. Press the GO key to resume printing.
There is no paper cassette installed in the printer that matches the paper size and paper type of the current job. Set alternative paper in the MP tray. Press the GO key to resume printing.
The memory card is accidentally removed from the memory card slot during reading.
If you continue reading the memory card, insert the same memory card into the slot again. The printer again reads it from the beginning of the data. Also see Insert the same memory card
on page 6.
A memory card error has occurred. Press the GO key to resume.
The total amount of data received by the printer exceeds the printer memory. Try adding more memory. Press the GO key to resume printing.
You have attempted to duplex-print while the duplexer is not installed. Install the duplex unit.
The stapler unit is not installed in the option document finisher. Install the stapler unit.
7
FS8000QR.book Page 8 Tuesday, December 25, 2001 10:47 AM
Message Corrective Action
Missing toner
TK-82 #######
Install the toner container using a toner kit for the particular color. The printer does not operate when this message is displayed.
Option interface
Error ##
A failure has occurred with the option network interface card. Check the option network interface card installed in the printer.
Option stacker cover open
Option stacker paper full
Option stacker path error
Option tray ## paper full
The cover of the optional output device
(stacker, document finisher, or sorter) is open. Close the cover.
The tray of the stacker is full. Remove paper sheets.
The optional stacker, document finisher, or sorter is not installed properly. Correct the installation.
A tray of the option sorter or the document finisher is full. Remove paper sheets in tray 01 to 09 as displayed in place of ##.
Paper feeder #
Side cover open
Paper jam
###############
Paper loading
The side cover of the paper feeder is open. Close the cover of the paper feeder
1 (topmost) to 3 (bottom) as displayed in place of #.
A paper jam has occurred. The location of the paper jam is indicated in place of the
#
's. For details, see section Clearing
Paper Jams on page 14.
After the paper cassette is closed, paper loading is in progress in the paper cassette.
8
FS8000QR.book Page 9 Tuesday, December 25, 2001 10:47 AM
Message Corrective Action
Print overrun
Press GO
† The print job transferred to the printer was too complex to print on a page. Press the
GO key to resume printing. (The page may break in some pages.).
You can abandon printing by the CANCEL key.
If Auto Continue is set to On, printing will be automatically resumed after a preset period of time.
RAM disk error ##
Press GO
A RAM disk error has occurred. Look at the error code given in place of ## and refer to the printer’s operation guide. To ignore the RAM disk error, press the GO key.
Remove paper option tray ##
Replace toner
Clean printer
Replace toner
TK-82 #######
Set paper
Press GO
Side cover open
Paper remains in optional sorter tray 1 to
9 as displayed in place of ##. Remove paper sheets.
Two message items are displayed alternately. Toner has run out in the toner container(s). Replace the toner container using a new toner kit for the particular color. The printer does not operate when this message is displayed.
For example, if Replace toner C,K is displayed, replace the cyan and the black toner containers.
The MP tray is out of paper. Load paper and press the GO key.
Open the side cover, then close tightly.
9
FS8000QR.book Page 10 Tuesday, December 25, 2001 10:47 AM
Message Corrective Action
Toner low
TK-82 #######
Unsupported external device
Virtual mail box full
Warning low memory
Replace the toner container using a new toner kit.
#######
: Color of the toner container that needs to be replaced. For example,
‘C’ means the Cyan toner container.
A device not supported by the printer is installed. Install an optional stacker supported by the printer.
The storage area in the hard disk for the virtual mailboxes is full. Print out accumulated jobs in the virtual mailboxes.
The printer's internal memory is running low due to too many numbers of fonts and macros downloaded. Try deleting unnecessary fonts and macros.
† After this error has happened, turn off page protect mode. See the Operation
Guide for details.
10
FS8000QR.book Page 11 Tuesday, December 25, 2001 10:47 AM
Loading Paper
1 Pull out the paper feed cassette until it stops. Lift the paper feed roller located on the right side of the cassette upright.
Paper Stopper
2
Adjust the position of the paper guides according to the size of the paper you will use. See the next page. To move the paper guides, press the greencolored knobs.
Paper Stopper
11
FS8000QR.book Page 12 Tuesday, December 25, 2001 10:47 AM
Align the paper stoppers correctly with the markings in the cassette that match the paper size:
A4
12
FS8000QR.book Page 13 Tuesday, December 25, 2001 10:47 AM
Square the edges
Paper Size Indicators Position insert into the paper feed cassette. Be sure that
Paper Guide the paper does not exceed the paper limit indicators. The paper
3 feed cassette can hold up to about
500 sheets. Printing is performed on the underside of the paper.
Lower the paper feed roller to its original position. Close the paper feed cassette.
13
FS8000QR.book Page 14 Tuesday, December 25, 2001 10:47 AM
Clearing Paper Jams
The figure below is a simplified diagram showing the paper path. You can clear paper jams easily and quickly if you become familiar with the paper path and locations of potential jams.
A
Depending on the indication on the message display, proceed as follows:
Caution
When removing jammed paper, use extreme care to leave no paper debris in the printer.
14
FS8000QR.book Page 15 Tuesday, December 25, 2001 10:47 AM
[Paper Jam — Feeder # Cover]
Open the paper feeder side cover according to the number in place of #, top (1) to bottom (3). Pull the paper outward. Close the side cover.
[Paper Jam — Cassette #]
Open the paper cassette according to the number in place of #, top
(1) to bottom (6).
Remove the paper in the paper cassette.
15
FS8000QR.book Page 16 Tuesday, December 25, 2001 10:47 AM
[Paper Jam — MP Tray]
Remove the jammed paper on the multi-purpose tray up and towards the right.
[Paper Jam — Duplexer Drawer]
Lower Cover
Open the duplexer drawer.
Open the plastic covers and remove paper under the covers and rollers.
Roller
16
FS8000QR.book Page 17 Tuesday, December 25, 2001 10:47 AM
[Paper Jam — Paper Feed Unit]
Open the front cover. Pull the paper feed unit out completely.
Paper Feed Unit
2
Remove the paper by swinging the green-colored lever to the right.
17
FS8000QR.book Page 18 Tuesday, December 25, 2001 10:47 AM
Remove the paper on the rubber belts.
4
3
Open the fuser access cover by pressing the green-colored lock lever.
18
FS8000QR.book Page 19 Tuesday, December 25, 2001 10:47 AM
5
Open the fuser top cover by simultaneously pulling the two lock levers.
6
Raise the subcover by grasping the clip marked as A on the rear side while removing the paper.
19
FS8000QR.book Page 20 Tuesday, December 25, 2001 10:47 AM
If the paper is pinched between the rollers, turn the wheel as shown towards you.
7
Stopper Lever
8
If driving the paper in the reverse direction will ease removing the paper, you can turn the wheel in the reverse direction by releasing the stopper lever.
Turn the greencolored lever down to the six o’clock position.
This allows you to draw out the primary transfer roller.
20
FS8000QR.book Page 21 Tuesday, December 25, 2001 10:47 AM
9
Turn the wheel
(with gear teeth) on the right-hand side of the primary transfer unit.
Remove the jammed paper.
Lock Button
Primary Transfer
Unit
10
10
Push the primary transfer unit back in. While pressing down the lock button, set the lock lever back to the original (four o’clock) position.
Caution
Use care not to touch the drum component in the primary transfer unit.
21
FS8000QR.book Page 22 Tuesday, December 25, 2001 10:47 AM
[Paper Jam — Side Cover]
1
Open the face-up tray. Open the side cover by pulling the handle.
2
Remove the jammed paper. If the paper does not go easily, refer to section
[Paper Jam —
Paper Feed Unit] on page 17.
22
FS8000QR.book Page 23 Tuesday, December 25, 2001 10:47 AM
[Paper Jam — Option Stacker]
Paper jam has occurred in the mailbox/sorter stacker, bulk stacker, or the document finisher which is an optional equipment. Remove paper jam in the option unit.
23
FS8000QR.book Page 24 Tuesday, December 25, 2001 10:47 AM
Toner Container Replacement
The life of the toner containers depends on the amount of toner required to accomplish your printing jobs.
When 5% coverage (a typical business document) of individual toner colors is assumed for A4 or letter size, the average life of each toner container is as follows
†
:
TK-82K Black
TK-82C Cyan
25,000 pages
10,000 images
TK-82M Magenta 10,000 images
TK-82Y Yellow 10,000 images
Replace the toner container when the printer displays, for example:
Toner low TK-82C
This is the first caution. Note the replacement is not always necessary at this stage. Replace the toner container immediately when the printer displays:
Replace Toner
Clean printer
24
† Excluding the starter toner containers
FS8000QR.book Page 25 Tuesday, December 25, 2001 10:47 AM
Replacing the Toner Container
Note
You do not have to turn printer power off before starting the replacement. Any data that may be under printing process will be deleted if you turn printer power off.
To replace the toner container, first make sure of the color of the toner container requiring replacement according to the message display. In this example, it is assumed that you are replacing the black toner container. To replace the other color toner container, use the same procedure.
Black (K)
Yellow (Y)
Magenta (M)
Cyan (C)
25
FS8000QR.book Page 26 Tuesday, December 25, 2001 10:47 AM
1
2
3
While pressing down the bluecolored lever at the end of the toner container, pull the toner container out.
Take the new toner container out of the toner kit. Hold the container and shake the container back and forth at least 5 times.
3
Insert the new toner container all the way in. The container is locked automatically when it is properly seated.
26
FS8000QR.book Page 27 Tuesday, December 25, 2001 10:47 AM
4
Put the old toner container in the plastic waste bag
(contained in the toner kit) and discard it.
When the toner container has been replaced, proceed to the next section.
Replacing the Waste Toner Bottle
Replace the waste toner bottle each time you replace the toner container. A new waste toner bottle is included with the toner kit. The printer will not operate without replacing the waste toner bottle.
Pull the paper feed unit all the way out.
1
Tilt to the right the lever on the righthand side of the bottle and remove the bottle. Do not place the removed bottle upside down.
27
FS8000QR.book Page 28 Tuesday, December 25, 2001 10:47 AM
2 The old waste toner bottle has a cap. Remove the cap (black) on the top of the bottle and put the cap onto the opening.
This is to prevent the toner from spilling.
Put the old waste toner bottle in the plastic waste bag
(contained in the toner kit) and discard it.
Insert the new waste toner bottle (contained in the toner kit) upright until it snaps into place.
3
Caution
Do not put the lid on the opening of a new waste toner bottle. This could cause damage to the printer.
28
FS8000QR.book Page 29 Tuesday, December 25, 2001 10:47 AM
Replacing the Oil Unit
The oil unit lasts an average of 25,000 pages and must be replaced when the printer displays the
Replace Oil kit
message.
1
Hot!
Open the front cover. Pull out the paper feed unit.
The fuser unit is very hot. Never proceed to the next step without cooling down the fuser.
Fuser
Note
The fuser unit is very hot. Never proceed to the next step until the fuser cools down.
29
FS8000QR.book Page 30 Tuesday, December 25, 2001 10:47 AM
2
Oil Unit
Open the front and rear release levers outward and remove the old oil unit.
Remove the sealing tapes at both ends of the new oil unit. Take out the new oil unit from the protective cover.
1
Cover
3
30
FS8000QR.book Page 31 Tuesday, December 25, 2001 10:47 AM
4
Attach the new oil unit. Seat it securely by pressing on the front and rear sides (the PUSH
HERE areas).
Push the paper feed unit back in.
Close the front cover.
Put the old oil unit in the cover and put it in the plastic bag (contained in the oil unit kit) and discard it.
5
31
FS8000QR.book Page 32 Tuesday, December 25, 2001 10:47 AM
Replacing the Maintenance Kit D
(Separation Charger Unit)
The following procedure is not necessary for
European countries and Australia.
Note
The separation charger unit needs to be replaced after every 100,000 pages of printing when the printer displays the message Install MK [D] (ATTENTION indicator flashes).
1 Open the front cover.
Pull the paper feed unit all the way out.
Paper Feed Unit
32
FS8000QR.book Page 33 Tuesday, December 25, 2001 10:47 AM
Separation
Charger
Unit
Projecting
Pin
2
Secondary
Transfer Unit
Remove the old separation charger unit from the secondary transfer unit. When you pull the projecting pin on the front end of the separation charger unit towards you as shown, the back end of the separation charger unit lifts up. Hold the back end of the separation charger unit to remove it.
33
FS8000QR.book Page 34 Tuesday, December 25, 2001 10:47 AM
3
Green Knob
(Separation Charger
Wire Cleaning knob)
Hold the new separation charger unit so that the projecting pin is in front of you and pass the green knob (separation charger wire cleaning knob) through the secondary transfer unit.
Press the back side to lock the unit.
Push the paper feed unit back in completely and close the front cover.
34
FS8000QR.book Page 35 Tuesday, December 25, 2001 10:47 AM
4
Ready
PAR A4 PLAIN
INTERFACE SIZE TYPE
Use the operator panel to reset the counter. Press the MENU key, then proceed as follows.
Press the MENU key. Press the [U] or [V] key repeatedly until Others > appears.
Others >
>Service
Press the [Z] key. Press the [U] or [V] key repeatedly until > Service > appears.
>
Press the [Z] key again. Press the [U] or [V] key repeatedly until >>Maintenance [D] appears.
>>Maintenance[D]
Press the ENTER key. A question mark (?) appears.
>>Maintenance[D]?
Press the ENTER key again. A question mark disappears and the counter of maintenance kit D is reset.
Press the MENU key. The message returns to
Ready
.
35
FS8000QR.book Page 36 Tuesday, December 25, 2001 10:47 AM
Cleaning the Printer
The following parts must be cleaned each time the toner container is replaced:
• Registration roller
• Belts
• Separation charger
• Main charger wire
• Main charger grid
These parts are explained in the following sections. In addition to this, it is recommended that these three parts are cleaned periodically at least once a month.
Cleaning the Paper Feed Unit
Print problems such as soiling of the reverse side of printed pages may occur if the paper feed unit becomes dirty. To clean the paper feed unit:
Open the front cover. Pull the paper feed unit out by its handle.
36
FS8000QR.book Page 37 Tuesday, December 25, 2001 10:47 AM
Belts
1
Clean the metal roller as shown
(the registration roller) using the cleaning cloth
(included in the toner kit).
Registration Roller
(Metal)
Clean the belts using the cleaning cloth.
Secondary Transfer
Roller (See Note below.)
2
Note
Be careful not to touch the black sponge roller
(the secondary transfer roller) during cleaning as this may adversely affect print quality.
37
FS8000QR.book Page 38 Tuesday, December 25, 2001 10:47 AM
3
Gently pull the green cleaning knob out and push it back in.
Repeat this 5 to 7 times. This cleans the separation charger inside.
Cleaning the Main Charger Unit
The main charger unit needs to be cleaned periodically as it gets contaminated with dioxide after a long usage, causing black streaks, etc. on the paper. The main charger is comprised of two main parts — the wire and the grid — which should be cleaned separately as instructed below:
38
FS8000QR.book Page 39 Tuesday, December 25, 2001 10:47 AM
1
2
Cleaning the main charger
wire — Grasp the tab of the cleaning knob (green) and gently pull out and push it back in 3 to 5 times.
Grid Cleaner
Cleaning the main charger
grid — Take the grid cleaner
(included in the toner kit) out of the protective bag and remove the cap.
Attach the grid cleaner to the printer, with the pad facing up.
39
FS8000QR.book Page 40 Tuesday, December 25, 2001 10:47 AM
Main Charger
Unit
3
Lock Lever
Slightly lift the main charger unit.
Gently pull the main charger unit out and push it back in. Repeat this 2 to 3 times.
These movements clean the grid at the bottom.
When finished, remove the grid cleaner from the printer and discard it. The grid cleaner cannot be reused.
Close the front cover.
40
FS8000QR.book Page 41 Tuesday, December 25, 2001 10:47 AM
Kyocera Corporation
14-9, Tamagawadai 2-Chome, Setagaya Ward
Tokyo 158-8610, Japan
FS-8000C
FS-8000CD
FS-8000CN
Color Printer
©2001 by Kyocera Corporation. All rights reserved. Revision 1.4., 2001.12
Printed in Japan
2BM80030D
Quick Reference Guide
ดาวน์โหลด
ลิงก์สาธารณะได้รับการอัปเดตแล้ว
ลิงก์สาธารณะไปยังแชทของคุณได้รับการอัปเดตแล้ว You may view and manage your chat links after registration here.
ลิงก์สาธารณะของเอกสาร
โฆษณา