Lightolier IS:40714 Instruction Sheet
Add to My manuals2 Pages
Lightolier IS:40714
The Lightolier IS:40714 is a traditional-style radiance pendant light fixture. It is designed for indoor use and can be mounted on a ceiling. The fixture comes with a canopy, crossbar, chain, and nipple. The canopy is attached to the ceiling, and the crossbar is attached to the canopy. The chain is attached to the crossbar, and the nipple is attached to the chain. The fixture also comes with three support stems, which are attached to the center stem assembly. The support stems are used to support the lower fixture assembly.
The Lightolier IS:40714 is a versatile fixture that can be used in a variety of settings. It is perfect for use in living rooms, dining rooms, bedrooms, and hallways. The fixture provides ample light and can be used to create a warm and inviting atmosphere.
advertisement
READ AND UNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXILfRE tis fixiure is intended for installation in accordancewiththe NefionalElectricalCodeandlocalregulations.
Jassurefull complianm with local codes and regulations, check with your Iocd electrical inapecfor before stallation. To prevent elestrfcal shock, turn oft elecfriufy at fuse box before proceeding.
Retain these inatructiona for maintenance reference.
INSTRUCTION SHEET NO.
IS:40714
1292 Page 1 of 2
INSTRUCTIONS FOR INSTALLATION
‘[XTUREASSEMBLY AND INSTALLATION:
OF TRADITIONAL STYLE RADIANCE PENDANTS
3. Mount CROSSBAR and CENTER STEM ASSEMBLY/CHAIN to OUTLET BOX using OUTLET BOX SCREWS (provided with outlet box).
4, Make electrica ccfnnections black ftiure lead or fixture lead without tracer marks to (hot) black supply lea~ white fixhrra lead or fixture lead with trecer mark to (neutral) white supply lead. Uninsulated wire is a ground and must be attached to GREEN GROUNO SCREW enclosed in CUPPEO WASHER and tightened in place to ctossbar, then sunnected to grounding terminal or ground lead inside OUTLET BOX. Use WIRENUTS (local hardware item).
CAUTION Push supply wires and wirenut connections back into OUTLkT BOX.
5. Adjust NIPPLE into CROSSBAR to proper CANOPY depth and secure NIPPLE in place by tightening LOCKNUT against CROSSBAR.
B, Slide CANOPY up CHAIN and secare against ceiling by thraadng KNURLED RING onto CANOPY LOOP.
7. Loosen and remove three BATTERY NUTS and STAR WASHERS from MOUNTING STUDS on LOWER FIXFURE ASSEMBLY.
8.
Raise LOWER FIXTURE ASSEMBLY to MOUNTING
PLATE on CENTER STEM ASSEMBLY and make electrical connections Snap together BLACK
●
9,
-%
1.1<>
FIG. 1
9-I TC>LI E la” RRiR511wM:E
WITWCTION SHEET NO.
!92
S:40714
Page 2 of 2
INSTRUCTIONS FOR INSTALLATION OF
TRADITIONAL STYLE RADIANCE PENDANTS CONTINUED
JPPORT STEM Attachment AND ADJUSTMEN~
1.
Loosen LOWER NUT on end of SUPPORT STEM until it is nearly to the end.
2. Hook opposite end at SUPPORT STEM onto the SUPPORT HOOK on CENTER STEM ASSEMBLY and allow SUPPORT STEM to swing down so the STEM rest in the SLOT in the SUPPORT BRACKET (Fig. 3A).
3. Tighten LOWER NUT against the SUPPORT BRACKET until SUPPORT STEM draws tight on SUPPORT HOOK (Fig. 3B).
4, Secure in place by tightening UPPER NUT against SUPPORT BRACKET (Fig. 3C).
5. Repeat for remaining SUPPORT STEMS.
IFFUSER CLEANING AND REMOVAL
CAUTION Turn power oft to fixture before attempting to clean.
Diffuser can be cleaned from above the fixture by removing lamps and cleaning DIFFUSER with a soft damp cloth, Should DIFFUSER need to be removed for cleaning, follow steps below,
1, Remove lamps ~om fixture,’
2, From below fixture, pushup on one side of the DIFFUSER and allow the oppositeside to drop down passed HOLDER KNOB (Fig. 1)
3. Stide DIFFUSER out on an angle from LOWER FIXTURE ASSEMBLY
NOTE DIFFUSER may have to be gentlycompressedon either side to pass fhmugh opening in LOWER FIXTURE ASSEMBLY.
●
●
/
I “Jk
FIG.
2
SUPPORTSTEM
UPPERNUT
)WER
NUT
SLOT
SUPPORTaRACKET
SUPPORTARM ~
@
(
LOWER
NUT
SUPPORTBRACKET
(
UPPER
NUT
-,
SUPPORT eRACKET
(
●
advertisement
Related manuals
advertisement