Linksys USBDSL1 User's Manual

Instant BroadbandTM Series
ADSL USB Modem
Use this guide to install the following:
Model No.: USBDSL1
User Guide
Instant BroadbandTM Series
Package Contents
ADSL USB Modem
Getting to Know
the ADSL USB Modem
Overview
Asymmetric Digital Subscriber Line (ADSL), the most popular residential
DSL technology, provides high-speed Internet access over regular, copper
phone lines by maximizing bandwidth use. In this way, ADSL Internet service
can coexist on the same line as your phone service, without disrupting calls.
ADSL is “asymmetric” because it downloads, or receives data, faster than
uploads it is transmitted. Asymmetric operation is ideal for home and small
office use where files and information are downloaded more frequently than
uploaded.
TM
• Instant Broadband ADSL USB Modem
• One USB Cable
• One Setup CD-ROM
• One User Guide and Registration Card
• One RJ-11 Telephone Wire (not shown)
There are several standard types of ADSL modulation techniques, including
Discrete Multitone (DMT). Your ADSL USB Modem supports the following
DSL standards: ANSI T1.413 Issue 2, ITU G.992.1 (G.DMT) and ITU
G.992.2 (G.lite).
The USB Icon
The USB icon shown below marks a USB port on a PC or device.
System Requirements
• Windows 98, 2000, or Millennium
• 300+ mHz Pentium II CPU or compatible system
• ADSL Internet service
• CD-ROM drive
Note: The ADSL USB Modem will not run under
Windows 95 or Windows NT.
To use this USB device, you must have Windows 98, 2000, or Millennium
installed on your PC. If you do not have Windows 98, 2000, or Millennium,
this device will not work.
Also, this device requires that a USB port is installed and enabled on your PC.
Some PCs have a disabled USB port. If your port doesn’t seem to be working,
there may be motherboard jumpers or a BIOS menu option that will enable the
USB port. See your PC’s user guide for details.
Some motherboards have USB interfaces, but no ports. You should be able to
install your own USB port and attach it to your PC’s motherboard using hardware purchased at most computer stores.
2
3
Instant BroadbandTM Series
The ADSL USB Modem’s Rear Panel Ports
ADSL USB Modem
Connecting the ADSL U S B
Modem to Your PC
Installing the ADSL USB Modem
1. Plug the rectangular end of the USB cable into your PC’s USB port.
Connect the square end of the USB cable into the Modem’s USB port. A
green Power LED will light up, indicating that the modem has been succesfully connected to your PC and that its power is on.
USB Port
Use this port to connect the USB cable from your PC to your
modem.
2. Connect a standard phone cable from the DSL outlet to the DSL port on
the ADSL USB Modem.
Your hardware installation is now complete.
Installing the Modem Driver for Windows 98
ADSL Port This port connects your modem to your ADSL line.
The ADSL USB Modem’s Front Panel LEDs
ADSL
Power
4
This LED will
light up when an
ADSL connection
is made. It will
also flicker when
an ADSL connection is being
made.
Windows 98 will automatically detect the ADSL USB Modem once it is connected to the PC. Before the hardware can function properly with your PC, a
Windows 98 driver for the ADSL USB modem must be installed.
1. Insert the Setup CD into your CD-ROM drive.
2. When the “Add New Hardware Wizard” window appears, make sure that the
Setup CD is in the CD-ROM drive and click Next.
The Power LED
will light up green
the modem has
successfully connected to your PC
and the modem’s
power is on.
5
Instant BroadbandTM Series
ADSL USB Modem
3. Select “Search for the best driver for your device” and click Next.
5. Windows will notify you that it is ready to install the driver. Click Next.
4. Select CD-ROM drive as the location where Windows will search for the
driver software and click Next.
6. After Windows has completed installing this driver, click Finish.
Your Windows 98 driver installation for the
ADSL USB Modem is now complete.
6
7
Instant BroadbandTM Series
Installing the Modem Driver for Windows Millennium
ADSL USB Modem
3. Windows will notify you that it has found the driver to install for your
modem. Click Next to install the driver.
1. Start up your PC in Windows Millennium. Windows will detect new hardware connected to your PC.
2. When Windows asks you for the location of the best driver, select
“Automatic search for a better driver (Recommended)” and click Next.
4. When Windows finishes installing the driver, click Finish.
8
9
Instant BroadbandTM Series
5. If Windows asks you for the location of Windows Millennium files, direct
your PC to the location of the files and click OK.
ADSL USB Modem
Installing the Modem Driver for Windows 2000
Windows 2000 will automatically detect the ADSL USB Modem once it is connected to the PC. Before the modem can function properly with your PC, you
must first install a Windows 2000 driver for the modem.
1. Insert the Setup CD into the CD-ROM drive. Windows will notify you that
it has detected new hardware.
Your driver installation for Windows
Millennium is now complete.
10
2. When the “Found New Hardware Wizard” screen appears to confirm that
the ADSL USB Modem has been connected to your PC, make sure the
Setup CD is in the CD-ROM drive and click Next.
11
ADSL USB Modem
ADSL USB Modem
3. Select “Search for a suitable driver for my device” and click Next.
5. Windows will notify you that it is ready to install the driver. Click Next.
6. When Windows has completed installing the first driver, click Finish.
4. Windows will now search for the driver software. Select CD-ROM drives
and click Next.
12
13
ADSL USB Modem
ADSL USB Modem
7. When Windows will ask you to search for a digital signature, click OK to
finish your installation.
Configuring Your ADSL USB Modem
Now that your installation is complete, you are ready to use your ADSL USB
Modem’s Configuration program. The configuration is modified through the
Linksys ADSL USB Adapter Properties screen. You may access this screen
one of two ways:
1. Right click on the Modem Icon in the system tray (the area next to the
clock) as pictured here.
After right clicking, choose the Properties option. The following screen will
appear.
Your Windows 2000 driver installation for
the ADSL USB Modem is now complete.
When this screen appears, enter <Alt>+A. The following screen will appear.
Click on the Advanced Monitoring button and the Linksys ADSL USB
Adapter Properties screen will appear.
14
15
Instant BroadbandTM Series
ADSL USB Modem
2. Or, the same screen may be accessed through the Control Panel by going
to Start, Settings, Control Panel, and click on the Linksys
ADSL USB Modem icon, shown below.
4. Press <Alt>+A to display the Properties window below. The “General” tab
on this screen displays information about your modem connection.
3. The Linksys ADSL USB Adapter Properties window will appear, displaying
your current data packet information and whether your DSL connection is up
or down. You
can click on
Clear to clear
the number of
bytes received
and transmitted.
5. Click on the ATM Link Statistics tab to display the status of your ATM
connection.
Click Help
for
more
detailed help.
16
17
Instant BroadbandTM Series
18
ADSL USB Modem
6.Click on the AAL Link Statistics tab to display information about your
AAL Adaption Layer.
8. Click on the Connection tab to display information about what features are
enabled when connecting to your provider.
7. Click on the AutoLog tab to display logging activity. Click on Enable
AutoLog Tool to activate this feature.
9. Click on the ATM OAM Loopback tab to manage the OAM Loopback
functions of your modem.
19
Instant BroadbandTM Series
10. Click on the TCP/IP tab to display information about your TCP/IP properties and configuration.
11. From the Linksys ADSL USB Adapter Properties screen, press <Alt>+C
to display the Properties window below. The Protocol Setup tab on this
screen allows you to change your protocol configuration.
20
ADSL USB Modem
12. Press <Alt>+P from the Linksys ADSL USB Adapter Properties screen to
display the Properties window below. As you will notice, this screen contains many of the tabs discussed earlier. The General tab displays more
detailed information about your modem connection.
13. Click on the Physical Layer Statistics tab to display your general power
usage information.
21
Instant BroadbandTM Series
14. For information on each of the following tabs, refer to the pages of this
guide indicated below:
ADSL USB Modem
16. Click on the Line Setup tab to setup or change the ADSL’s operational
mode.
ATM Link Statistics - page 17
AAL Link Statistics - page 18
Protocol Setup - page 21
ATM OAM Loopback - page 19
TCP/IP - page 20
Conection - page 18
AutoLog - page 17
15. Click on the HAL Diagnostics tab to obtain information about the average send and receive rates of your modem.
17. Click on the ATM Statistics tab to give information about your current
ATM statistics.
22
23
Instant BroadbandTM Series
18. Click on the AAL Statistics tab to display information about your current
AAL statistics.
ADSL USB Modem
Troubleshooting
Common Problems and Solutions
This section offers solutions to common issues that may occur during the
installation and operation of your ADSL USB Modem.
1. Which protocols might I need to use with my ADSL USB Modem?
• Refer to the documentation or manual provided by your ISP for details.
The protocol required in your configuration depends on the equipment
used by your DSL service provider. There are several possibilities:
a. Point-to-Point Protocol Over ATM (PPPoA) (RFC 2364) - PPP
provides session setup, user authentication (login), and encapsulation
for upper-layer protocols such as IP (Internet Protocol). The use of
PPP makes the modem appear as a dial modem to the operating sys
tem. Dial-Up Networking is used to establish a connection. PPP is
supported by either the WAN (Wide Area Network) driver or the
ATM driver.
b. Bridged/Routed Ethernet/IP over ATM (RFC 1483) - This protocol makes the modem appear as a local area network (LAN) device
to the operating system.
c. Point-to-Point Protocol Over Ethernet (PPPoE) (RFC 2516) - PPP
provides session setup, user authentication (login), and encapsulation
for upper-layer protocols such as IP (Internet Protocol). PPP makes
the modem appear as a dial modem to the operating system. Dial-Up
Networking is used to establish a connection. The protocol must be
supported by WinPoet or Enternet 300 logon software on the RFC
1483 driver.
2. Installing the driver software resulted in unexpected errors or warnings.
Uninstall the ADSL USB Modem driver by doing the following:
a. Go to Start, Settings, Control Panel, and click on Add/Remove
Programs.
b. Highlight Linksys ADSL USB Modem.
c. Close the Control Panel window, and remove the program.
25
http://www.linksys.com
© Copyright 2000 Linksys, All Rights Reserved.