7

2

Marshall Electronics

BC-0909-DA Universal Digital Converter Users Guide

Product Overview

The BC-0909-DA is a Universal Digital converter for digital HDSDI to Analog HD (SMPTE-274M) YprPb, or RGB or

SDI to Analog Composite, Y/C, YUV, or RGB with support of 480i, 480P, 720P, 1080 24P, 1080i formats. The Digital to Analog conversion in this module employs 10bit sampling and data path with 4x over sampling of chroma and an adaptive filter process.

Features

• Active loop through for HDSDI signal with re-clocking and re-shaping

• Automatic detection range of 142Mb/s to 1.485Gb/s

• Automatic Compensation of HDSDI input for cable length up to 300’

• Converts HDSDI to Analog High Definition RGB (SOG) or Y-Pr-Pb

• Converts SDI to Analog Composite (PAL/NTSC)

• Converts SDI to Y/C (S-Video)

• Converts SDI to Analog Component YUV (Y/R-y/B-y), or RGB (SOG)

• Automatic color space conversion

• Rotary switch for output signal type

• 10-bit processing with 4x over sampling

Electrical Specifications

Signal Input

Screen Formats

Signal Output

Output Standards

System Sample Frequency

Dynamic gain/phase

Y/C delay

Frequency Response

Signal to Noise

Differential gain/phase

Input Cable length

BNC for HDSDI/SDI signals that conform to SMPTE-259M/292M

640 x 480 - 50i, 59.97i, 60i

1280 x 720 - 23.97P, 24P, 25P, 29.97P, 30P, 59.96P, 60P

1920 x 1080 - 23.97P, 24P, 25P, 29.94P, 30P, 50i, 59.94i, 60i

HD-15 (Analog component RGB, YPrPb, Composite, Y/C) via included

RGB-5HD15-6 Break out cable

SMPTE-170M for SDI inputs

SMPTE-274M/296 for HDSDI inputs

54Mhz

<0.4% / 0.4°

<2%/2°

-0.9db

<57db

<0.5% / <0.7°

1000ft (300m)

Mechanical Specifications

Dimensions

Approx. Weight

Power required

4.75”W x 3.75”D x 1.0”H (120.65mm x 95.25mm x 25.4mm)

0.55 lbs

6V D.C. supplied from external supply

Included Accessories

• Power Supply (Class 2, (Model V-PS6-12A)

• RGB-5HD15-6 Break out cable

• Users Guide

• Wall Mount Brackets

• Foot Pads for desktop or stacking

Optional Accessories

A. 2 Module Rack Mount Kit (Model V-CRM2)

B. 3 Module Rack Mount Kit (Model V-CRM3)

Desktop Stand (Model V-CB1)

A.

B.

1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • www.LCDRacks.com • Email: [email protected]

BC-0909-DA Universal Digital Converter Users Guide

7

Operational Setup

1. Unpack the BC-0909-DA and accompanying V-PS6-1.2A power supply. Physically inspect for any damage that may have occurred during shipping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact Marshall Electronics at

800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2. Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on the sides, closest to the rear of the unit. (See Below) Only one screw per side should be removed.

Use the same screw to attach the bracket with the flange facing away from the side and parallel to the front of the BC-0909-DA metal case. The flange has two holes. For desktop use, apply the supplied rubber pads.

3. Connect required cables for signal input and output.

Please note that power must be applied to the BC-0909-DA for the Analog Output and HDSDI/SDI Loop out to be activated. All BNC connectors should be rated for 75Ω.

3. Plug the V-PS6-1.2A power supply into the A.C. source

4. Attach twist lock power connection from V-PS6-1.2A power supply to the back of the unit.

5. Turn on the BC-0909-DA by depressing the power switch located on the front of the unit.

Refer to Page 4 picture for location of switch settings.

Bracket Installation

Feet Installation

7 7

Input Connectors

HDSDI or SDI Out Re-

Clocked and Shaped Signal

Requires Power to be applied for activation

Analog Signals Out

Refer to table below for pin-out

6 VDC from

V-PS6-1.2A power supply

Left Pin - Pos

Right Pin- Neg

Switch Settings & Indicators

Input Signal Standard Indicator

High Defi nition or Standard Defi nition

Illuminates when SDI or

HDSDI signal is present

Pin1

Pin2

Pin3

Pin4

Pin5

Pin6

Pin7

Pin8

Pin9

Signal

Type

HD Analog color difference

YPbPr

Pr

Y

Pb

SD Analog color difference

Y, R-Y, B-Y

R-Y

Y

B-Y

S-Video

Y/C

C

Y

Ground Ground

HD or SD

Analog RGB

(Sync on Green)

Red

Green

Blue

Ground

HD-15

BNC Breakout

Red

Green

Blue

Ground

Ground

Ground

Power On/Off indicator

Output Signal Format

Video- Only active in SD mode output Composite Video

YUV – Only active in SD mode output Component Video

Y-Pr-Pb – Only active in HD mode output Component Video

RGB – Active in HD and SD mode output RGB with Sync on Green Signal

Warranty

Marshall Electronics warranties to the fi rst consumer, that this BC-0909-DA Digital to Analog Converter will, under normal use be free from defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the purchasing end user only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.

This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifi cations in design or construction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.

Due to constant effort to improve products and product features, specifi cations may change without notice.

1910 East Maple Ave. El Segundo, CA 90245 • Tel.: 800-800-6608 • Fax:310-333-0688 • www.LCDRacks.com • Email: [email protected]