Instruction Manual
1/2/4 Port USB 2.0 Extender over Cat5 or Cat6 - Up to 330 ft (100m)
USB2001EXT2/USB2002EXT2/USB2004EXT2
LED Status Indicators DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Packaging Contents
• 1 x USB extender Transmitter/Local unit
• 1 x USB extender Receiver/Remote unit
• 1 x Power Adapter
• 3 x Power Cord (NA/UK/EU)
• 4 x Mounting Bracket
• 1 x USB cable
• 1 x Installation Guide
System Requirements
• USB enabled computer system with available USB port
• Available AC power outlet
• Solid core Category 5e unshielded twisted pair (UTP) or greater cabling.
Installation
1. Place the Local and Remote units at the desired locations and connect together using RJ45 terminated Cat5 or Cat6 cabling.
a) If you are using surface cabling, ensure you have enough Cat5e cabling to connect the Local Unit to the Remote Unit’s location, and that each end is terminated with a RJ45 connector. The cabling cannot go through any networking equipment (i.e. router, switch).
OR
b) If you are using premise cabling, ensure that the Cat5e cabling between the Local Unit to the Remote Unit has been properly terminated in a wall outlet in each location and there is a patch cable long enough to connect the Remote Unit to their respective outlets. The cabling cannot go through any networking equipment (i.e. router, switch).
2. Connect the included power adapter to the Local unit
(USB2002EXT2) or the Remote unit (USB2004EXT2/USB2001EXT2).
The Power LED should light up solid.
3. Connect the Local unit to the host computer system with a USB cable. The computer can be either powered On or Off. The operating system should detect the extender and install it automatically.
4. USB devices can now be connected to the Remote unit.
USB2001EXT2 Front
USB Type A
Connector
Remote Unit
USB Device
Status LED
Indicators
Extender Status
LED Indicators
USB2002EXT2 Front
USB Type A
Connector
Remote Unit
USB Device
Status LED
Indicators
Extender Status
LED Indicators
USB2004EXT2 Front
USB Type A
Connector
Remote Unit
USB Device
Status LED
Indicators
Extender Status
LED Indicators
Local Unit
Extender Status
LED Indicators
Local Unit
Extender Status
LED Indicators
Local Unit
Extender Status
LED Indicators
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 01/22/2015
Specifications
Bus Interface
Number of Ports
Connectors
(Local unit)
Connectors
(Remote unit)
LEDs
(Local unit)
LEDs
(Remote unit)
Maximum Data
Transfer Rate
Maximum Cable
Distance
Compatible
Cabling
ESD Protection
Power Adapter
Operating
Temperature
Storage
Temperature
Operating
Humidity
USB2001EXT2
1
1 x USB type B female
1 x RJ45 Ethernet female
1 x USB type A female
1 x RJ45 Ethernet
Female
1 x DC Power
1 x Power
1 x Remote Link
1 x Host Link
1 x Activity
1 x Device Status
USB2002EXT2
USB 2.0
2
1 x USB type B female
1 x RJ45 Ethernet female
1 x DC Power
2 x USB type A female
1 x RJ45 Ethernet female
1 x Power
1 x Remote Link
1 x Host Link
1 x Activity
1 x Power
1 x Remote Link
1 x Host Link
1 x Activity
2 x Device Status
USB 2.0: 480 Mbps
100 m / 330 ft
Category 5e/6/6a
USB2004EXT2
4
1 x USB type B female
1 x RJ45 Ethernet female
4 x USB type A female
1 x RJ45 Ethernet female
1 x DC Power
1 x Power
1 x Remote Link
1 x Host Link
1 x Activity
4 x Device Status
8kV Contact, 16kV Air 4kV Contact, 8kV Air 8kV Contact, 16kV Air
5VDC, 1000mA 24VDC, 1000mA 5VDC, 1000mA
0°C ~ 50°C (32°F ~ 122°F)
-20°C ~ 70°C (-4°F ~ 158°F)
20% ~ 80% RH
LED
Power
Link
Host
Activity
Device
USB2001EXT2 Back
Remote
Remote
Description
Solid: Power is being supplied
Solid: Link established between Local and Remote units
Solid: Detected and installed by the host computer
Flashing: Local and Remote units are in suspend mode
Flashing: Data transmission between Local and Remote units
Off: Local and Remote units are in suspended mode
USB2002EXT2 Back
USB2004EXT2 Back
Remote
Power
Connector
Green: Device Enumerated
Orange: Overcurrent
Off: No Device, or Not Enumerated
Local
Local
Local
USB type B
Connector
(Host)
Power
Connector
USB type B
Connector
(Host)
Power
Connector
USB type B
Connector
(Host)
Dimensions 100.0mm x 76.0mm x 26.0mm (each)
Weight 600 g (each)
Power
Connector
Power
Connector
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
