Onkyo TX-SR573 Instruction manual

AV Receiver

TX-SR573

Instruction Manual

Thank you for purchasing an Onkyo AV receiver.

Please read this manual thoroughly before making connections and plugging in the unit.

Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver.

Please retain this manual for future reference.

Contents

Introduction ..................................... 2

Connections .................................. 15

Turning On & First Time Setup..... 30

Basic Operation

Playing your AV components ....... 34

Listening to AM/FM Stations........ 36

Listening to XM Satellite Radio..... 37

Using the Listening Modes .......... 44

Advanced Operation ..................... 50

Troubleshooting ............................ 59

E n

2

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

PORTABLE CART WARNING

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen into the apparatus,

C. If the apparatus has been exposed to rain or water,

D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in any way, and

F. When the apparatus exhibits a distinct change in performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of this unit.

17. Batteries

Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel

(e.g., AC 120 V, 60 Hz).

Setting the [STANDBY/ON] switch to STANDBY does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

6. Handling Notes

• If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

Memory Backup

The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it’s unplugged or in the case of a power failure.

Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

Modèle canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME

NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

3

4

Supplied Accessories

Make sure you have the following accessories:

Remote controller & three batteries (AA/R6)

Indoor FM antenna

AM loop antenna

Speaker Cable

1

2

3

Speaker cable labels

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operation are the same regardless of color.

Features

Amp

• 7-channel amplifier

• 75 watts per channel min. RMS at 8

Ω, 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion

• WRAT (Wide Range Amplifier Technology)

• Optimum gain volume circuitry

Processing

• Dolby

*1

Digital EX and Dolby Pro Logic IIx

• DTS, DTS-ES Matrix/Discrete, DTS Neo:6, and DTS

96/24 processing

*2

• CinemaFILTER function

• Linear PCM 192 kHz/24-bit D/A converters on all channels

• Powerful and highly accurate 32-bit DSP Processing

Audio/Video

• Adjustable crossover (60, 80, 100, 120, 150 Hz)

• HDTV-capable component video (3 inputs, 1 output)

• 3 S-Video inputs, 2 outputs

• 4 assignable digital inputs (3 optical, 1 coaxial)

• Subwoofer pre out

• Color-coded multichannel input for use with Super

Audio CD and DVD-Audio

• A/B speaker drive

• Color-coded speaker terminal posts

Tuner

• XM Satellite Radio

*3

(XM Connect-and-Play antenna accessory required; sold separately)

• 30 AM/FM/XM presets

• AM/FM auto tuning

Remote Controller

• Preprogrammed for use with other AV components

• Learning function

• Macro function

*1. Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are registered trademarks of Dolby Laboratories.

*2. “DTS,” “DTS 96/24,” “DTS-ES,” and “Neo:6” are trademarks of Digital Theater Systems, Inc.

*3. XM Connect & Play™, XM Ready

®

, XM Public

Radio™ are trademarks of XM Satellite Radio Inc.

©2005 XM Satellite Radio Inc. All rights reserved.

All other trademarks are the property of their respective owners.

Apple and iPod are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Contents

Introduction

Important Safety Instructions ....................2

Precautions .................................................3

Supplied Accessories.................................4

Features .......................................................4

Front & Rear Panels....................................6

Remote Controller.......................................9

Connection

Connecting Your Speakers ......................15

Connecting Antenna .................................18

Connecting Your Components ................20

About AV Connections ............................20

Connecting Audio & Video Signals to the AV Receiver ................................21

Which Connections Should I Use? ..........21

TV or Projector ........................................22

DVD player ..............................................23

VCR or DVD Recorder for Playback........24

VCR or DVD Recorder for Recording ......25

Camcorder, Games Console, or Other Device .....................................25

Satellite, Cable, Set-top Box, or Other Video Source...........................26

CD Player or Turntable ............................27

Cassette, CDR, MiniDisc, or DAT Recorder ...................................28

Connecting Another Component’s

Power Cord ...........................................28

Components ..........................................29

Connecting the Power Cord ....................29

Turning On & First Time Setup

Turning On the AV Receiver ....................30

Turning On & Standby .............................30

First Time Setup ........................................31

Assigning Digital Inputs to Sources .........31

Changing the Input Display .....................31

Speaker Configuration .............................32

Basic Operation

Playing Your AV Components ................ 34

Basic AV Receiver Operation ................. 34

Using the Multichannel DVD Input .......... 35

Displaying Source Information ................ 35

Listening to the Radio.............................. 36

Listening to AM/FM Stations ................... 36

Listening to XM Satellite Radio

®

............. 37

Presetting AM/FM Stations &

XM Channels ........................................ 41

Common Functions.................................. 42

Setting the Display Brightness ................ 42

Adjusting the Bass & Treble.................... 42

Muting the AV Receiver .......................... 42

Using the Sleep Timer ............................ 43

Using Headphones ................................. 43

Adjusting Speaker Levels ....................... 43

Using the Listening Modes

Using the Listening Modes...................... 44

Selecting the Listening Modes ................ 44

About the Listening Modes ..................... 46

Using the Late Night Function................. 48

Using the CinemaFILTER ....................... 48

Using the Audio Adjust Settings.............. 48

Advanced Operation

Recording.................................................. 50

Recording the Input Source .................... 50

Recording from Different Sources........... 50

Advanced Setup ....................................... 51

Advanced Speaker Settings.................... 51

Digital Signal Formats............................. 53

Controlling Other Components............... 54

Entering Remote Control Codes ............. 54

Resetting the Remote Controller............. 55

Learning Commands from Other Remote

Controllers ............................................ 57

Using Macros .......................................... 58

Troubleshooting ....................................... 59

Specification ............................................. 62

5

6

Front & Rear Panels

Front Panel

1 2 3 4 5 6 7 8 9 J K L

TUNING / PRESET

M

MASTER VOLUME

STANDBY/ON

ENTER

STANDBY

A SPEAKERS B

PHONES

TONE

MULTl CH DVD

+

STEREO LISTENING MODE

VIDEO 1 VIDEO 2

DISPLAY DIGITAL INPUT

VIDEO 3

DIMMER MEMORY TUNING MODE

CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

N O P Q

The actual front panel has various logos printed on it.

They are not shown here for clarity.

For detailed information, see the pages in parentheses.

A

STANDBY/ON button (30)

This button is used to set the AV receiver to On or

Standby.

B

STANDBY indicator (30)

This indicator lights up when the AV receiver is in

Standby mode, and it flashes while a signal is being received from the remote controller.

C

Remote-control sensor (9)

This sensor receives control signals from the remote controller.

D

STEREO button (44)

This button is used to select the Stereo listening mode.

E

LISTENING MODE [ ]/[ ] buttons (44)

These buttons are used to select the listening modes.

F

Display

See “Display” on page 7.

G

DISPLAY button (35)

This button is used to display various information about the currently selected input source.

H

DIGITAL INPUT button (31)

This button is used to assign the digital inputs and specify the format of digital input signals.

I

DIMMER button (42)

This button is used to adjust the display brightness.

J

MEMORY button (41)

This button is used when storing or deleting radio presets.

K

TUNING MODE button (36)

This button is used to select the Auto or Manual tuning mode for AM and FM radio.

VIDEO

VIDEO 3 INPUT

L AUDIO R

R S T

L

Arrow/TUNING/PRESET & ENTER buttons

When AM, FM, or XM is selected, the TUNING

[ ] [ ] buttons are used to tune the tuner, and the

PRESET [ ] [ ] buttons are used to select radio presets (see page 41). When the setup menus are used, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.

M

MASTER VOLUME control (34)

This control is used to set the volume of the AV receiver to MIN, 1 through 79, or MAX.

N

PHONES jack (43)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

O

SPEAKER A & B buttons (34)

These buttons are used to turn speaker sets A and B on or off.

P

TONE, [–] & [+] buttons (42)

These buttons are used to adjust the bass and treble.

Q

Input selector buttons (34)

These buttons are used to select the following input sources: MULTI CH, DVD, VIDEO 1, VIDEO 2,

VIDEO 3, TAPE, TUNER, or CD.

The [MULTI CH] button selects the multichannel

DVD input.

R

RETURN button

This button is used to return to the previously displayed setup menu.

S

SETUP button

This button is used to access various settings.

T

VIDEO 3 INPUT (25, 50)

This input can be used to connect a camcorder, games console, and so on. There are jacks for composite video and analog audio.

Front & Rear Panels—Continued

Display

1 2 3

5


1

A & B speaker indicators (34)

Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on.

2

MUTING indicator (42)

This indicator flashes when the AV receiver is muted.

3

Source/listening mode indicators (46)

These indicators show the currently selected listening mode and digital audio format.

4

Tuning indicators (36)

TUNED (36): This indicator lights up when the AV receiver is tuned to a radio station or channel.

AUTO (36): For AM and FM radio, this indicator lights up when Auto Tuning is selected, and disappears when Manual Tuning is selected.

MEMORY (41): This indicator lights up when presetting radio stations.

FM STEREO (36): This indicator lights up when the AV receiver is tuned to a stereo FM station.

5

SLEEP indicator (43)

This indicator lights up when the Sleep function has been set.

6

Message area

This area of the display shows various information about the currently selected source.

6

4

7

Front & Rear Panels—Continued

Rear Panel

1 B 3 4 5 6 7

8

8 9 J K L

A

DIGITAL IN OPTICAL 1, 2, 3 & COAXIAL

These optical and coaxial jacks can be used to connect a CD or DVD player and other components with digital audio outputs.

B

COMPONENT VIDEO

A DVD player, TV, or other component that supports component video can be connected here.

C

AM ANTENNA

These push terminals are for connecting an AM antenna.

D

FM ANTENNA

This jack is for connecting an FM antenna.

E

MONITOR OUT

The S-Video or composite video output should be connected to a video input on your TV or projector.

F

XM ANTENNA

This jack is for connecting an XM antenna, sold separately (see page 37).

G

FRONT SPEAKERS B

These push terminals are for connecting speaker set B.

H

This (Remote Interactive) jack can be connected to the jack on another Onkyo component. To use , you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

Note:

can only be used with Onkyo components.

I

CD IN

These analog inputs can be used to connect a CD player with analog outputs.

M N O

J

TAPE IN/OUT

These analog inputs and outputs can be used to connect a cassette recorder, MiniDisc recorder, or other recorder with analog inputs and outputs.

K

VIDEO 1 IN/OUT & VIDEO 2 IN

The VIDEO 1 S-Video, composite video, and audio inputs and outputs can be used to connect a VCR.

The VIDEO 2 S-Video, composite video, and audio inputs can be used to connect another video source

(e.g., cable TV, satellite TV, or a set-top box).

L

DVD IN/MULTI CH INPUT

The FRONT, SURROUND, CENTER, and SUB-

WOOFER jacks can be used to connect a component with an analog multichannel audio output, such as a DVD player with a 5.1-channel analog output.

The S-Video or composite video input should be connected to a video output on the DVD player.

M

SUBWOOFER PRE OUT

A powered subwoofer can be connected here.

N

FRONT SPEAKERS A, SURROUND

SPEAKERS, CENTER SPEAKER &

SURROUND BACK SPEAKERS

These terminal posts are for connecting speaker set A.

O

AC OUTLET

This switched AC outlet can be used to supply power to another component. The connector type depends on the country in which you purchased your AV receiver.

See pages 15–29 for hookup information.

Remote Controller

Installing the Batteries

1 To open the battery compartment, press the small hollow and slide open the cover.

Using the Remote Controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

STANDBY indicator

2 Insert the three supplied batteries (AA/R6)

3 in accordance with the polarity diagram inside the battery compartment.

Slide the cover shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Approx. 16 ft.

(5 m)

Notes:

• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

9

10

Remote Controller—Continued

About the Remote Controller Modes

Including the AV receiver, the remote controller can be used to control up to nine different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the eight REMOTE MODE buttons.

■ RECEIVER/TAPE Mode

In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via

.

■ DVD Mode

By default, you can control an Onkyo DVD player in this mode. By entering the appropriate remote control code, you can control components made by other manufacturers (see page 54).

■ CD Mode

By default, you can control an Onkyo CD player in this mode. By entering the appropriate remote control code, you can control a CD player, MD player, or CD recorder made by another manufacturer (see page 54).

■ HDD Mode

This mode is for controlling Onkyo’s next generation

HDD-compatible components via .

■ TV & VCR Modes

With these modes, you can control a TV and VCR. You must enter the appropriate remote control code first (see page 54).

■ CABLE/CDR & SAT/MD Modes

In CABLE/CDR mode, you can control an Onkyo CD recorder, or a cable TV receiver. In SAT/MD mode, you can control an Onkyo MD recorder, or a satellite TV receiver. You must enter the appropriate remote control code first (see page 54).

RECEIVER/TAPE Mode

RECEIVER/TAPE mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .

To set the remote controller to RECEIVER/TAPE mode, press the [RECEIVER] REMOTE MODE button.

A

B

C

D

RECEIVER

1

5

F

G

H

I

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV

DIMMER

VCR CABLE

CDR

TV VOL

HDD

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

-

PREV

CH

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

L

M

N

O

P

Q

R

S

1 Use the REMOTE MODE buttons to select a mode.

2 Use the buttons supported by that mode to control the component.

RECEIVER/TAPE mode: see page 10

DVD mode: see page 12

CD/MD/CDR modes: see page 13

HDD mode: see page 14

TV/VCR/SAT/CABLE modes: see page 56

Note:

Some of the remote controller operations described in this manual may not work as expected with other components.

J

2

K

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL

OPEN/CLOSE VIDEO OFF

LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

T

U



A

STANDBY button (30)

This button is used to set the AV receiver to

Standby.

B

ON button (30)

This button is used to turn on the AV receiver.

C

INPUT SELECTOR buttons (34)

These buttons are used to select the input sources.

D

MULTI CH button (35)

This button is used to select the multichannel DVD input.

E

DIMMER button (42)

This button is used to adjust the display brightness.

F

Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons

These buttons are used to select and adjust settings.

G

CH +/– button (41)

This button is used to select radio presets.

H

RETURN button

This button is used to return to the previous display when changing settings.

I

DISPLAY button (35)

This button is used to display various information about the currently selected input source.

J

LISTENING MODE buttons (44)


The [STEREO], [SURR], and LISTENING MODE

[ ]/[ ] buttons can be used regardless of the currently selected remote controller mode.

STEREO button

This button selects the Stereo listening mode.

SURR button

This button selects the Dolby and DTS listening modes.

LISTENING MODE [ ]/[ ] buttons


DIRECT button

This button selects the Direct listening mode.

ALL ST button

This button selects the All Channel Stereo listening mode.

K

TEST TONE, CH SEL, LEVEL- & LEVEL+ buttons (33)

These buttons are used to adjust the level of each speaker.

L

MACRO buttons (58)

These buttons are used with the Macro function.

M

REMOTE MODE buttons (10)

These buttons are used to select the remote controller modes. When you press a button on the remote controller, the REMOTE MODE button for the currently selected mode lights up.

N

SLEEP button (43)

This button is used to set the Sleep function.

O

MENU button (38)

This button is used to select the search mode for

XM Satellite Radio.

P

VOL [ ]/[ ] button (34)

This button can be used to adjust the volume of the

AV receiver regardless of the currently selected remote controller mode.

Q

SETUP button

This button is used to access various settings.

R

MUTING button (42)

This button is used to mute the AV receiver.

S

SP A & SP B buttons (34)

These buttons are used to turn speaker sets A and B on or off.

T

CINE FLTR button (48)

This button is used to set the CinemaFILTER function.

U

L NIGHT button (48)

This button is used to set the Late Night function.

■ TAPE mode

For twin cassette decks, only Deck B can be controlled.

1 Previous & Next [ ]/[ ] buttons

The Previous [ ] button is used to select the previous track. During playback it selects the beginning of the current track. The Next [ ] button is used to select the next track.

Depending on how it was recorded, the Previous and Next [ ]/[ ] buttons may not work properly with some cassette tapes.

Play [ ] button

This button is used to start playback.

Rewind & FF [ ]/[ ] buttons

The Rewind [ ] button is used to start rewind. The

FF [ ] button is used to start fast forward.

Reverse Play [ ] button

This button is used to start reverse playback.

Stop [ ] button

This button is used to stop playback.

REC [ ] button

This button is used to start recording.

2 Eject [ ] button

This button is used to eject the cassette tape.

11

12


DVD Mode

To set the remote controller to DVD mode, press the

[DVD] REMOTE MODE button.

A

B

C

DVD

D

E

F

G

H

I

J

K

L

+

CH

DISC

ALBUM

-

PREV

CH

DISPLAY

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV VOL

HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

RE

TURN

ENTER

SET

UP

VOL

MUTING

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

M

N

O

P

Q

R

S

A

STANDBY button

This button sets the DVD player to Standby.

B

ON button

This button is used to turn on the DVD player.

C

Number buttons

These buttons are used to enter title, chapter, and track numbers and to enter times for locating specific points in time.

D

TOP MENU button

This button is used to select a DVD’s top menu.

E


These buttons are used to navigate DVD menus and the DVD player’s onscreen setup menus.

F

DISC +/– button

This button selects discs on a DVD changer.

G

RETURN button

This button is used to exit the DVD player’s onscreen setup menu and to restart menu playback.

H

DISPLAY button

This button is used to display information about the current disc, title, chapter, or track on the DVD player’s display, including the elapsed time, remaining time, total time, and so on.

I

Playback buttons

From left to right: Previous, Play, Next, Fast

Reverse, Pause, Stop, Fast Forward, Slow Reverse, and Slow Forward.

J

REPEAT button

This button is used to set the repeat playback functions.

K

AUDIO button

This button selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).

L

OPEN/CLOSE [ ] button

This button is used to open and close the disc tray.

M

CLEAR button

This button is used to cancel functions and to clear entered numbers.

N

MENU button

This button is used to display a DVD’s menu.

O

SETUP button

This button is used to access the DVD player’s onscreen setup menus.

P

RANDOM button

This button is used with the random playback function.

Q

PLAY MODE button

This button is used to select play modes on a component with selectable play modes.

R

SUBTITLE button

This button is used to select subtitles.

S

VIDEO OFF button

This button is used to turn off the internal video circuitry, eliminating any possibility of interference.


CD, MD & CDR Modes

To control an Onkyo CD player, or a CD/MD recorder made by another manufacturer, press the

[CD] REMOTE MODE button to select the CD remote controller mode.

To control an Onkyo MD recorder or CD recorder, press the [MD] or [CDR] REMOTE MODE button to select the MD or CDR remote controller mode.

To control an Onkyo MD recorder or CD recorder, or a component made by another manufacturer, you must first enter the appropriate remote control code (see page 54).

A

B

C

F

7

8

CDR

D

E

9

J

+

CH

DISC

ALBUM

-

PREV

CH

DISPLAY

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV VOL

HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

RE

TURN

ENTER

SET

UP

VOL

MUTING

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

K

CD

MD

L

M

N

A

STANDBY button

This button sets the CD player or MD/CD recorder to Standby.

B

ON button

This button is used to set the CD player or MD/CD recorder to On or Standby.

C

Number buttons

These buttons are used to enter track numbers and to enter times for locating specific points in time.

D


These buttons can be used with some components.

E

DISC +/– button

This button selects discs on a CD changer.

F

DISPLAY button

This button is used to display information about the current disc or track on the CD player or MD/CD recorder’s display, including the elapsed time, remaining time, total time, and so on.

G

Playback buttons

From left to right: Previous, Play, Next, Fast

Reverse, Pause, Stop, and Fast Forward.

H

REC [ ] button

This button is used to start recording on an MD or

CD recorder.

I

REPEAT button

This button is used to set the repeat playback functions.

J

OPEN/CLOSE [ ] button

This button is used to open and close the disc tray, or eject the MiniDisc.

K

CLEAR button

This button is used to cancel functions and to clear entered numbers.

L

RETURN button

This button can be used with some components.

M

RANDOM button

This button is used with the random playback function.

N

PLAY MODE button

This button is used to select play modes on a component with selectable play modes.

13


14

HDD Mode

HDD mode is for controlling Onkyo’s next generation

HDD-compatible components. As of 2005, it can be used with the Onkyo DS-A1 Remote Interactive Dock and

Apple iPod connected via .

When Using the DS-A1:

• Connect the DS-A1 to the TAPE IN or VIDEO 2 IN jacks.

• Set the DS-A1’s RI MODE switch to HDD.

• Set the AV receiver’s input display to HDD (see page 31).

• Refer to the DS-A1’s instruction manual.

A

B

C

D

5

F

G

8

9

J

+

CH

DISC

ALBUM

-

PREV

CH

DISPLAY

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

TV VOL

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU MEN

U

RE

TURN

ENTER

SET

UP

VOL

MUTING

HDD

K

L

M

N

O

P REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

A

STANDBY button

This button turns off the HDD-compatible component.

B

ON button*

This button turns on the HDD-compatible component.

C

Arrow [ ]/[ ] and ENTER buttons*

These buttons are used to navigate menus on the

HDD-compatible component.

D

ALBUM +/– button*

This button selects the next or previous album on the HDD-compatible component.

E

DISPLAY button*

This button turns on the backlight for 30 seconds on the HDD-compatible component.

F

Previous [ ] button

This button restarts the current song on the HDDcompatible component. Press it twice to select the previous song.

G

Pause [ ] button

This button pauses playback on the HDD-compatible component. (With 3rd generation iPods, it works as a Play/Pause button.)

H

Rewind [ ] button

Press and hold to rewind the HDD-compatible component.

I

PLAYLIST [ ]/[ ] buttons*

These buttons select the previous or next playlist on the HDD-compatible component.

J

REPEAT button*

This button sets the Repeat function to One, All, or

Off on the HDD-compatible component.

K

MENU button*

This button is used to navigate menus on the HDDcompatible component.

L

Play [ ] button

This button starts playback on the HDD-compatible component. If the component is off, it will turn on automatically. (With 3rd generation iPods, this button works as a Play/Pause button.)

M

Next [ ] button

This button selects the next song on the HDD-compatible component.

N

Stop [ ] button

This button stops playback and displays the menu on the HDD-compatible component.

O

Fast Forward [ ] button

Press and hold to fast forward the HDD-compatible component.

P

RANDOM button*

This button sets the Shuffle function to Songs,

Albums, or Off on the HDD-compatible component.

* Buttons marked with an asterisk (*) are not supported by

3rd generation iPods.

Connecting Your Speakers

About Speakers

You can use two sets of speakers with the AV receiver: speaker set A and speaker set B.

Speaker set A should be installed in your main listening room, and can be used with Dolby Digital and DTS sources.

To get the best surround sound experience, each speaker must be positioned at a specific location within the room, as shown in the following illustration. Note that while speaker set B is on, speaker set A is reduced to 5.1-channel playback.

Speaker set B can be installed in another room and positioned like normal stereo speakers or however you like. Speaker set B only outputs sources that are connected to an analog input.

Front left and right speakers

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies, it’s used mainly for dialog.

Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.

Surround back left and right speakers

These speakers further enhance the realism of surround sound and improve sound localization behind the listener. They are essential to enjoy certain listening modes

(i.e., Dolby Digital EX and

DTS-ES). Position them behind the listener about 2–

3 feet (60–100 cm) above ear level. Make sure that the listening position is within the range of the speakers.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel.

The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the wall, as shown.

1/3 wall position

Corner position

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience.

Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally, they should be equally spaced from the listener.

15

16

Connecting Your Speakers—Continued

How Many Speakers?

For the best surround-sound experience, you should connect seven speakers and a powered subwoofer.

The following table shows which channels you should use based on the number of speakers that you have.

Number of speakers: 2 3 4 5 6 7

Front left

Front right

Center

Surround left

Surround right

Surround back*

Surround back left

Surround back right

✓ ✓ ✓ ✓ ✓ ✓

✓ ✓ ✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓ ✓ ✓ ✓

✓

✓

✓

*If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass.

Before using the AV receiver, you must specify which speakers are connected and their sizes (see page 32).

To get the very best from your surround-sound system, you should also specify the distance between the listener and each speaker so that the sound from each speaker arrives at the listener’s ears at the same time (see page 52). In addition, you should set the volume level of each speaker so that all speakers can be heard equally at the listening position (see page 52.)

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of 6 ohms or higher. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp-protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals to only positive

(+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the

AV receiver.

• Don’t connect a speaker to several terminals.

Attaching the Speaker Labels

The AV receiver’s positive (+) speaker terminals are color-coded for ease of identification. (The negative (–) speaker terminals are all black.)

Speaker terminal

Front left

Front right

Center

Surround left

Surround right

Surround back left

Surround back right

Color

White

Red

Green

Blue

Gray

Brown

Tan

The supplied speaker labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.

Connecting Your Speakers—Continued

Connecting Speaker Set A

1 Strip 5/8" (15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

5/8" (15 mm)

2 Unscrew the terminal. Fully insert the bare wires.

Make sure that the bare wire is touching the inside of the pole. Screw the terminal tight.

Connecting Speaker Set B

1 Strip 3/8" (10 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

2 While pressing the lever, insert the wire into the hole, and then release the lever.

Make sure that the terminals are gripping the bare wires, not the insulation.

3/8" (10 mm)

Note:

While speaker set B is on, speaker set A is reduced to

5.1-channel playback.

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s SUB-

WOOFER PRE OUT to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the SUBWOOFER

PRE OUT to the amp’s input.

Note:

Make sure the plugs are pushed in all the way.

This hookup diagram shows which speaker should be connected to each pair of terminals.

If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

Front right speaker

Speaker Set A

Center speaker

Front left speaker

Front right speaker

Front left speaker

Speaker Set B

LINE INPUT

Powered subwoofer

Surround back right speaker

Surround back left speaker

Surround right speaker

Surround left speaker

17

18

Connecting Antenna

This section explains how to connect the supplied indoor

FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals

FM antenna jack

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

1 Assemble the AM loop antenna, inserting the tabs into the base, as shown.

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

1 Attach the FM antenna, as shown.

2 Connect both wires of the AM loop antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around).

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

2 Use thumbtacks or something similar to fix the FM antenna into position.

Thumbtacks, etc.

Push Insert Release

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 19).

Caution: Be careful that you don’t injure yourself when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 19).

Connecting Antenna—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied

AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

■ Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

TV/FM antenna splitter

To AV receiver To TV (or VCR)

19

20

Connecting Your Components

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing.

AV Connection Color Coding

RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Analog audio

Left (white)

Right (red)

Left (white)

Right (red)

(Yellow)

Composite video

(Yellow)

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

Right!

Wrong!

AV Cables & Jacks

Video

Component video cable

Y

P

B

P

R

Cable

S-Video cable

Composite video cable

Audio

Y

P

B

P

R

Y

P B

P R

Jack

S

V

Description

Component video separates the luminance (Y) and color difference signals (P R , P B ), providing the best picture quality. (Some TV manufacturers label their component video jacks slightly differently.)

S-Video separates the luminance and color signals and provides better picture quality than composite video.

Composite video is commonly used on TVs, VCRs, and other video equipment. Use only dedicated composite video cables.

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

Multichannel analog audio cable (RCA)

Cable

COAXIAL

L

R

Jack

OPTICAL

Description

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.

This cable carries multichannel analog audio and is typically used to connect DVD players with a 5.1channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

Connecting Your Components—Continued

Connecting Audio & Video Signals to the AV Receiver

By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.

: Signal Flow

Video

Video

Audio Audio

TV, projector, etc.

DVD player, etc.

Speakers (see page 17 for hookup details)

Which Connections Should I Use?

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.

For video components, such as a DVD player, you must make an audio connection and a video connection.

Video Connection Formats

Video equipment can be connected to the AV receiver using one of the following video connection formats: composite video, S-Video, or component video, the latter offering the best picture quality.

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.

For example, if you connect your DVD player to the

S-VIDEO DVD IN, a video signal will be output by the

S-VIDEO MONITOR OUT (for your TV) and the

S-VIDEO VIDEO 1 OUT (for your VCR), but not by any composite video or component video outputs.

Audio Connection Formats

Audio equipment can be connected to the AV receiver using the following audio connection formats: analog, optical, coaxial, and multichannel.

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats.

For example, audio signals connected to an OPTICAL or

COAXIAL digital input are not output by the analog

TAPE OUT, so if you want to record from, for example, your CD player, in addition to connecting it to a digital input, you must also connect it to the analog CD IN.

Video Signal Flow Chart

DVD player, etc.

Output

IN

AV receiver

Composite

Composite

OUT

Input

Composite

S-Video

S-Video

S-Video

Component

Component

Component

Audio Signal Flow Chart for Recording

CD player, etc.

Optical Coaxial Analog

Output

IN

Analog

AV receiver

Optical Coaxial

OUT

Input

Cassette recorder, etc.

Analog

Multichannel

Multichannel


Note:

Speaker set A outputs all input sources. Speaker set B only outputs sources that are connected to an analog input.

21

22


Connecting a TV or Projector

Step 1: Video Connection

Choose a connection that matches your TV ( , , or C ), and then make the connection.

A COMPONENT VIDEO

Y

P B

P R

MONITOR

OUT

V

C

MONITOR

OUT

S

B

COMPONENT VIDEO

IN

Y

P B

P R


S VIDEO IN

Connection

A

B

C

AV receiver

COMPONENT VIDEO OUT

MONITOR OUT S

MONITOR OUT V

VIDEO IN

Signal flow

⇒

⇒

⇒

TV

Component video input

S-Video input

Composite video input

Picture quality

Best

Better

Standard

Step 2: Audio Connection

Choose a connection that matches your TV ( a , b , or c ), and then make the connection.

Connect one or the other b

DIGITAL IN c

COAXIAL

OPTICAL

2

IN

L

R

VIDEO 2 a

COAXIAL

OUT

OPTICAL

OUT


L

R

AUDIO

OUT

• With connection a , you can listen to and record audio from your TV and listen via speaker set B.

• To enjoy Dolby and DTS listening modes, use connection b or c . (For recording, use a and b , or a and c .)

Connection a b c

AV receiver

VIDEO 2 IN L/R

DIGITAL IN COAXIAL

DIGITAL IN OPTICAL 2

Signal flow

⇐

⇐

⇐

TV

Analog audio L/R output

Digital coaxial output

Digital optical output

Hint!

If your TV has no audio outputs, connect an audio output from your VCR to the AV receiver and use its tuner to listen to TV programs through the AV receiver.


Connecting a DVD player


Choose a connection that matches your DVD player ( , , or C ) , and then make the connection.

A

COMPONENT VIDEO

DVD IN

Y

P B

P R

COMPONENT VIDEO

OUT

Y

P B

P R

DVD player

S VIDEO OUT

DVD

V

IN

DVD

S

IN

C

B

Your TV must be connected to the AV receiver via the same type of connection.

VIDEO OUT

Connection

A

B

C

AV receiver

COMPONENT VIDEO DVD IN

DVD IN S

DVD IN V

Signal flow

⇐

⇐

⇐

DVD player

Component video output

S-Video output

Composite video output

Picture quality

Best

Better

Standard


Choose a connection that matches your DVD player ( a , b , c , or d ), and then make the connection.

b

DIGITAL IN

FRONT

L

DVD

R a

L d

FRONT SURROUND CENTER

Connect one or the other

COAXIAL

OPTICAL

1

R

DVD

SURR

SUB

WOOFER

CENTER FRONT

L

COAXIAL

OUT

L R

R

OPTICAL

OUT

AUDIO

OUT

DVD player

SUB

WOOFER

• With connection a , you can listen to and record audio from a DVD and listen via speaker set B.


• To enjoy DVD-Audio or SACD playback with a compatible player, use connection d .

Connection a b c d

AV receiver

DVD IN FRONT

DIGITAL IN COAXIAL


DVD IN FRONT, SURROUND,

CENTER, and SUBWOOFER

Signal flow

⇐

⇐

⇐

⇐

DVD player




Analog multichannel output

• If your DVD player has stereo left and right outputs and multichannel left and right outputs, be sure to use the stereo left and right outputs for connection a .

23

24


Connecting a VCR or DVD Recorder for Playback

In addition to video playback, with this hookup example, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver. This is useful if your TV has no audio outputs.


Choose a connection that matches your VCR or DVD recorder ( , , or C ) , and then make the connection. Your

TV must be connected to the AV receiver via the same type of connection.

A COMPONENT VIDEO

VIDEO 1 IN

Y

P B

P R

COMPONENT VIDEO

OUT

Y

P B

P R VCR, DVD recorder

S VIDEO OUT

VIDEO OUT

VIDEO 1

V

IN

C

VIDEO 1

S

IN

B

Connection

A

B

C

AV receiver

COMPONENT VIDEO VIDEO 1 IN

VIDEO 1 IN S

VIDEO 1 IN V

Signal flow VCR or DVD recorder

⇐

⇐

⇐


S-Video output


Picture quality

Best

Better

Standard


Choose a connection ( a , b , or c ), and then make the connection.

Connect one or the other b DIGITAL IN

COAXIAL c

OPTICAL

2

L

IN

R

VIDEO 1 a

COAXIAL

OUT

OPTICAL

OUT

L

R

AUDIO

OUT

VCR, DVD recorder

• With connection a , you can listen to the VCR or DVD recorder, including via speaker set B.

• To enjoy Dolby and DTS listening modes, use connection b or c . (To listen via speaker set B, use a and b , a c


AV receiver

VIDEO 1 IN L/R

DIGITAL IN COAXIAL


Signal flow

⇐

⇐

⇐

VCR/DVD recorder





Connecting a VCR or DVD Recorder for Recording

Step 1: Choose a video connection that matches your VCR or DVD recorder ( A or B ), and make the connection.

The video source that you want to record must be connected to the AV receiver via the same type of connection.

Step 2: Make audio connection a .

VIDEO 1

V

B a

L

R

VIDEO 1

VIDEO 1

S

A

Connection

A

B a

L

AUDIO

IN

R

VCR,

DVD recorder

AV receiver

VIDEO 1 OUT S

VIDEO 1 OUT V

VIDEO 1 OUT L/R

S VIDEO IN

Signal flow

⇒

⇒

⇒

VIDEO IN

VCR/DVD recorder

S-Video input

Composite video input

Audio L/R input

Picture quality

Better

Standard

—

Connecting a Camcorder, Games Console, or Other Device

Step 1: Make video connection A .

Step 2: Make audio connection a .

Connection

A a

TUNING / PRESET

ENTER


CLEAR

RETURN SETUP

TAPE TUNER CD

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

A VIDEO 3 INPUT

AV receiver

VIDEO 3 INPUT

VIDEO 3 INPUT L/R a

VIDEO 3 INPUT

L AUDIO R

L AUDIO

OUT

R

VIDEO OUT

Camcorder, games console, etc.

Signal flow

⇐

⇐

Camcorder/console



25

26


Connecting a Satellite, Cable, Set-top Box, or Other Video Source


Choose a connection that matches the video source ( , , or C ) , and then make the connection.

A

COMPONENT VIDEO

VIDEO 2 IN

Y

P B

P R

VIDEO 2

V

IN

VIDEO 2

S

IN

C

B

Your TV must be connected to the AV receiver via the same type of connection.

COMPONENT VIDEO

OUT

Y

P B

P R

S VIDEO OUT

Satellite, cable, set-top box, etc.

VIDEO OUT

Connection

A

B

C

AV receiver

COMPONENT VIDEO VIDEO 2 IN

VIDEO 2 IN S

VIDEO 2 IN V

Signal flow

⇐

⇐

⇐

Video source


S-Video output


Picture quality

Best

Better

Standard


Choose a connection that matches the video source ( a , b , or c ), and then make the connection.

Connect one or the other b

DIGITAL IN c

COAXIAL

OPTICAL

2

IN

L

R

VIDEO 2 a

COAXIAL

OUT

L

OPTICAL

OUT Satellite, cable, set-top box, etc.

R

AUDIO

OUT

• With connection a , you can listen to and record audio from the video source and listen via speaker set B.



AV receiver

VIDEO 2 IN L/R

DIGITAL IN COAXIAL


Signal flow

⇐

⇐

⇐

Video source





Connecting a CD Player or Turntable

■ CD Player or Turntable with Built-in Phono Preamp

Step 1:

Choose a connection that matches your CD player ( a , b , or c ), and then make the connection. Use connection a for a turntable with a built-in phono preamp.

b

DIGITAL IN

L

IN

L c

COAXIAL

IN

R

CD

R

AUDIO

OUTPUT Connect one or the other

OPTICAL

1

L a

R

CD a

COAXIAL

OUT

L R

OPTICAL

OUT

AUDIO

OUT

CD player

Turntable (MM) with built-in phono preamp

• With connection a , you can listen to and record from your CD player or turntable and listen via speaker set B.

• To connect the CD player digitally, use connection b or c . (For recording, use a and b , or a and c .)


AV receiver

CD IN L/R

DIGITAL IN COAXIAL


Signal flow

⇐

⇐

⇐

CD or turntable




■ Turntable with no Phono Preamp Built-in

A phono preamp is necessary to connect a turntable that doesn’t have a phono preamp built-in.

■ Turntable with an MC (Moving Coil) Cartridge

An MC head amp and phono preamp are necessary to connect a turntable with an MC (Moving Coil) cartridge.

L

IN

R

CD

AUDIO

OUTPUT

L

R

Phono preamp

AUDIO

OUTPUT

L

R

AUDIO

INPUT

L

R

L

IN

R

CD

AUDIO

OUTPUT

L

R

L

AUDIO

INPUT

R

Phono preamp

MC head amp or

MC transformer

AUDIO

OUTPUT

L

R

AUDIO

OUTPUT

L

R

AUDIO

INPUT

L

R

27

28


Connecting a Cassette, CDR, MiniDisc, or DAT Recorder

Step 1:

Choose a connection that matches the recorder ( a , b , or c ), and then make the connection.

b

DIGITAL IN

Connect one or the other c

COAXIAL

OUT IN

L

OPTICAL

3

L

TAPE

R

L

COAXIAL

OUT

OPTICAL

OUT

R

IN OUT

R

REC PLAY

Cassette recorder, CDR, etc.

• With connection a , you can play and record with the recorder and listen via speaker set B.

• To connect the recorder digitally (playback only), use connections a and b , or a and c . a


AV receiver

TAPE IN L/R

TAPE OUT L/R

DIGITAL IN COAXIAL


Signal flow

⇐

⇒

⇐

⇐

Cassette/CDR/MD/DAT recorder


Analog audio L/R input



Connecting Another Component’s Power Cord

The AV receiver has an AC outlet on its rear panel for connecting the power cord of another AV component.

The other component’s power switch can then be left in the ON position so that it turns on or off when the AV receiver is set to On or Standby.

Caution:

• Make sure that the capacity of the component that you connect to the AC OUTLET does not exceed the stated capacity (e.g., 120 W).

Note:

• Onkyo components connected via should be connected directly to a wall outlet, not the AV receiver’s AC OUTLET.


Connecting -capable Onkyo Components

Step 1: Make sure that the Onkyo component is connected to the AV receiver with an analog audio cable (RCA).

Step 2: Make the connection.

With (Remote Interactive) you can use the following special functions:

Auto Power On/Standby

When you start playback on a component connected via , if the AV receiver is on Standby, it will automatically turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components connected via will also go on Standby. This function will not work with components whose power cord is connected to the AV receiver’s AC OUTLET.

Direct Change

When playback is started on a component connected via , the AV receiver automatically selects that component as the input source. If your DVD player is connected to the AV receiver’s multichannel DVD input, you’ll need to press the [MULTI CH] button to hear all channels (page 35), as the Direct Change function only selects the FRONT jacks.

Remote Control

You can use the AV receiver’s remote controller to control your other -capable Onkyo components, pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (page 55).

Notes:

• Use only cables for connections. cables are supplied with Onkyo players (DVD,

CD, etc.).

• Some components have two jacks, you can connect either one to the AV receiver. The other jack is for connecting additional -capable components.

• Connect the AV receiver’s jack only to Onkyo components. Connecting to other manufacturer’s components may cause them to malfunction.

• Some components may not support all functions. Refer to the manuals supplied with your other Onkyo components.

• If you connect an Onkyo MD recorder, CD recorder, or next generation HDD-compatible component, you must change the input display

(see page 31).

REMOTE

CONTROL e.g., CD player e.g., DVD player

L

IN

R

CD

FRONT

L

R

DVD

R L

ANALOG

AUDIO OUT

R L

ANALOG

AUDIO OUT

Connecting the Power Cord

• Before connecting the power cord, connect all of your speakers and AV components.

• Connect the AV receiver’s power cord to a suitable wall outlet.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

29

30

Turning On the AV Receiver

STANDBY/ON

STANDBY indicator

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD

+ STEREO LISTENING MODE

VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

STANDBY

ON

RECEIVER

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

Turning On & Standby

AV receiver

STANDBY/ON or

Remote controller

RECEIVER

Press the [STANDBY/ON] button.

Alternatively, press the remote controller’s [RECEIVER] button, followed by the [ON] button.

The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.

ON

To turn the AV receiver off, press its [STANDBY/ON] button, or press the remote controller’s [STANDBY] button. The AV receiver will enter Standby mode. To prevent any loud surprises when you next turn on the AV receiver, always turn down the volume before you turn it off.

Note:

Pressing the remote controller’s [ON] button once will turn on the AV receiver. Pressing it again will turn on any components connected via .

Smooth Operation in a Few Easy Steps

To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once.

■ Have you connected a component to a digital audio input?

If you have, see “Assigning Digital Inputs to Sources” on page 31.

COAX

OPT1

■ Have you connected an Onkyo MD recorder, CD recorder, or next generation HDD-compatible component?

OUT IN

If you have, see “Changing the Input Display” on page 31.

TAPE

CD recorder, MD recorder,

RI Dock, etc.

■ Do the speaker configuration—this is essential!

See “Speaker Configuration” on page 32.

First Time Setup

Assigning Digital Inputs to Sources

2, 3

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN

TAPE TUNER CD

SETUP

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

1

To enjoy Dolby Digital and DTS sources, you must connect your DVD player to the AV receiver digitally (coaxial or optical).

With this function, you can assign digital inputs to input sources. If, for example, you connect your DVD player to the DIGITAL IN OPTICAL 1 input (OPT1), you’ll need to assign it to the DVD input source, as follows.

Note:

Make sure that components connected digitally are configured to output digital audio. Refer to the relevant manuals.

1

DVD

VIDEO 3

VIDEO 1

VCR

TAPE

VIDEO 2

TUNER

Press the input selector button for the input source that you want to assign.

(Digital inputs cannot be assigned to the TUNER input source.)

CD

Changing the Input Display

If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT or VIDEO 2 IN jacks, for to work properly, you must change this setting.

This setting can only be changed on the AV receiver.

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

1, 2 1, 2

iPod photo: If you’re using an iPod photo with the

DS-A1 Remote Interactive Dock, connect the DS-A1 to the VIDEO 2 IN jacks.

1

TAPE

Press the [TAPE] or [VIDEO 2] input selector button so that

“TAPE” or “VIDEO 2” appears on the display.

or

VIDEO 2

2

DIGITAL INPUT

Press the [DIGITAL INPUT] button.

The current assignment appears.

3

DIGITAL INPUT

Press the [DIGITAL INPUT] button repeatedly to select COAX,

OPT1, OPT2, OPT3, or “– – – –”

(analog).

2

TAPE or

VIDEO 2

Press and hold down the [TAPE] or [VIDEO 2] input selector button (about 3 seconds) to change the setting.

Repeat this step to select MD, CDR, or

HDD.

For the TAPE input selector, the setting changes in this order:

TAPE

→

MD

→

CDR

→

HDD

For the VIDEO 2 input selector, the setting changes in this order:

VIDEO 2

↔

HDD

Note:

HDD can be selected for the TAPE input selector or

VIDEO 2 input selector, but not both at the same time.

31

32

First Time Setup—Continued

2

ENTER

Use the Up and Down [ ]/[ ] buttons to select “1. Speaker

Config,” and then press the

[ENTER] button.

2–8

1

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

-

PREV

CH

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

1, 9

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

Speaker Configuration

This section explains how to specify your speaker configuration.

For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large. For those with a smaller diameter, specify Small.

Cone diameter

1

RECEIVER

Press the [RECEIVER] button, followed by the [SETUP] button.

ENTER

3

4

5

ENTER

ENTER

ENTER

ENTER

ENTER

While the “Subwoofer” setting is selected, use the Left and Right

[ ]/[ ] buttons to select Yes or

No.

Yes: Select if a subwoofer is connected.

No: Select if no subwoofer is connected.

Use the Down [ ] button to select “Front,” and then use the

Left and Right [ ]/[ ] buttons to select Small or Large.

Small: Select if the front speakers are small.

Large: Select if the front speakers are large.

Note:

• If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear.

Use the Down [ ] button to select “Center,” and then use the

Left and Right [ ]/[ ] buttons to select Small, Large, or None.

Small: Select if the center speaker is small.

Large: Select if the center speaker is large.

None: Select if no center speaker is connected.

Note:

• If the Front setting in step 4 is set to

Small, the Large option cannot be selected.

First Time Setup—Continued

6

ENTER

7

8

9

ENTER

ENTER

ENTER

ENTER

ENTER

Use the Down [ ] button to select “Surround,” and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or

None.

Small: Select if the surround speakers are small.

Large: Select if the surround speakers are large.

None: Select if no surround speakers are connected.

Note:

• If the Front setting in step 4 is set to

Small, the Large option cannot be selected.

Use the Down [ ] button to select “Surr Back,” and use the

Left and Right [ ]/[ ] buttons to select Small, Large, or None.

Small: Select if the surround back speakers are small.

Large: Select if the surround back speakers are large.

None: Select if no surround back speakers are connected.

Notes:

• If the Surround setting in step 6 is set to None, this setting does not appear.

• If the Surround setting in step 6 is set to Small, the Large option cannot be selected.

Use the Down [ ] button to select “Surr Back Ch,” and use the Left and Right [ ]/[ ] buttons to select 2ch or 1ch.

2ch: Select if two (left and right) surround back speakers are connected.

1ch: Select if one surround back speaker is connected.

Note:

• If the Surround and Surr Back settings in steps 6 and 7 are set to None, this setting does not appear.

Press the [SETUP] button.

Speaker configuration is complete.

Testing the Speakers

To make sure that all of the speakers are working properly, press the remote controller’s [TEST

TONE] button. A test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again.

• If the test tone is not produced by a speaker, or it’s produced by a speaker other than the one shown on the display, you may have wired it incorrectly and should check your connections (see page 17).

• If the test tone is not produced by a speaker, and its name does not appear on the display, check the speaker configuration (see page 32).

33

34

Playing Your AV Components

Basic AV Receiver Operation

2

DISPLAY

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

4

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

MULTI CH

1

1

1

2

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10

0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

RET

URN

SET

UP

DISPLAY MUTING

4

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

1

DVD

AV receiver

VIDEO 1 VIDEO 2

VIDEO 3

VCR

TAPE

CD

TUNER

V1

1

CD

7


Use the AV receiver’s input selector buttons to select the input source.

RECEIVER

V2

2

TAPE

8

To select the input source with the remote controller, press the

[RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons.

V3

3

DVD

6

TUNER

9

On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1,

VIDEO 2, and VIDEO 3 input sources respectively.

2

3

AV receiver

A SPEAKERS B

4

AV receiver

MASTER VOLUME


SP A


VOL

SP B

To turn the speakers on or off, use the AV receiver’s SPEAKERS [A] and

[B] buttons, or use the remote controller’s [SP A] and [SP B] buttons.

The A and B speaker indicators show whether each speaker set is on or off.

Note that while speaker set B is on, speaker set A is reduced to 5.1-channel playback.

Indicators

Start playback on the source component.

To watch a DVD or other video source, on your TV, select the video input that’s connected to the AV receiver’s MONITOR OUT jack.

To adjust the volume, use the MASTER VOLUME control, or the remote controller’s [VOL] button.

The volume can be set to MIN, 1 through 79, or MAX. Since the AV receiver is designed for home theaters, it has a wide volume range for precise adjustment.

5 Select a listening mode and enjoy!

See “Using the Listening Modes” on page 44.

Playing Your AV Components—Continued

MULTI CH

RECEIVER

DISPLAY

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU MEN

U

+

CH

DISC

ALBUM

PREV

CH

-

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

Using the Multichannel DVD Input

The multichannel DVD input is for connecting a component with a 5.1-channel analog audio output, such as a

DVD-Audio or SACD-capable DVD player, or an

MPEG decoder. See page 23 for hookup information.

RECEIVER

MULTI CH

5

Press the [RECEIVER] REMOTE

MODE button, followed by the

[MULTI CH] button.

The MULTI CH indicator appears on the display.

MULTI CH indicator

Displaying Source Information

You can display various information about the current input source as follows.

RECEIVER


MODE button, and then press the

[DISPLAY] button repeatedly to cycle through the available information.

DISPLAY

The following information can typically be displayed:

Input source & volume

Signal format* or sampling frequency

Input source & listening mode

*If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not

PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears.

Interpreting Surround Channel Information

A B C

A: The number of front channels (front left, front right, and center).

B: The number of surround channels (surround left and surround right). If there’s surround back channel information, this number will be 3.

C: LFE channel for subwoofer (1 means yes).

Audio from the multichannel DVD input will now be used for the DVD input source.

Note:

• While the multichannel DVD input is selected, the

Speaker Configuration settings on page 32 are ignored, and signals from the multichannel DVD input are fed to the front left, front right, center, surround left, and surround right speakers, and subwoofer as they are.

35

36

Listening to the Radio

Listening to AM/FM Stations

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING MODE

TUNING

TUNING / PRESET

MASTER VOLUME

ENTER

TONE

MULTl CH DVD

+ STEREO

VIDEO 1

LISTENING MODE

VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

VIDEO

VIDEO 3 INPUT

L AUDIO R

TUNER

With the built-in tuner, you can enjoy AM and FM radio stations, and store your favorite stations as presets for easy selection.

1

TUNER

Use the [TUNER] input selector button to select AM or FM.

In this example, FM has been selected.

■ Manual Tuning Mode

1

TUNING MODE

Press the [TUNING MODE] button so that the AUTO indicator disappears from the display.

2

TUNING / PRESET

ENTER

Press and hold the TUNING Up or

Down [ ]/[ ] button.

The frequency stops changing when you release the button.

Press the buttons repeatedly to change the frequency one step at a time.

The American model changes FM frequency in 0.2 MHz steps, 10 kHz steps for AM.

In Manual Tuning mode, FM stations will be in mono.

Tuning into Weak FM Stereo Stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to

Manual Tuning mode and listen to the station in mono.

Band Frequency

(Actual display depends on country.)

Tuning into AM/FM Radio Stations

■ Auto Tuning Mode

1

TUNING MODE

Press the [TUNING MODE] button so that the AUTO indicator appears on the display.

Displaying AM/FM Radio Information

1

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

TAPE TUNER

RETURN SETUP

CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

2

TUNING / PRESET

ENTER

Press the TUNING Up or Down

[ ]/[ ] button.

Searching stops when a station is found.

1

DISPLAY

Press the [DISPLAY] button repeatedly to cycle through the available information.

Band, frequency, and preset #

When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM

STEREO indicator also appears.

TUNED AUTO

Listening mode

FM STEREO

Listening to the Radio—Continued

Listening to XM Satellite Radio

®

What’s XM Satellite Radio?

There is a world beyond AM and FM. It is XM Satellite Radio. XM offers more than 150 digital channels of audio entertainment, including 100% commercial-free music channels, in the top markets in the U.S.

Note: An XM Connect-and-Play™ antenna and monthly subscription are required to receive XM Satellite Radio. Visit www.xmradio.com for details.

Note:

Hardware and required basic monthly subscription sold separately. Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-

XMRADIO. Subscriptions subject to Customer Agreement available at xmradio.com. Only available in the 48 contiguous United States.

A warning against reverse engineering:

It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE

®

voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this product.

Connecting the XM Antenna

The XM antenna is sold separately. You can purchase the

XM Connect-and-Play antenna from the XM Web site at: http://www.xmradio.com

Connect the Connect-and-Play antenna to the XM antenna jack on the rear panel.

XM antenna jack

Signing Up for XM Satellite Radio

Before you can use XM Satellite Radio, you must first sign up for an account. You’ll need a major credit card and your XM Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the Connect-and-Play package and itself.

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

1 2

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

1

2

TUNER

TUNING / PRESET

ENTER

Press the [TUNER] input selector button repeatedly to select XM.

If “CHECK ANTENNA” appears on the display, make sure the XM antenna is connected properly.

Use the TUNING Up and Down

[ ]/[ ] buttons to select channel 0.

Your XM Satellite Radio ID number is displayed. Write it below.

3

ID

To sign up, go to: http://activate.xmradio.com

Or call: 1-800-967-2346

Notes:

• Channel 0 cannot be selected in Category Search mode. You must select Channel Search mode (see page 38).

• The following letters are not used in XM Satellite

Radio IDs: I, O, S, F.

Put the XM antenna by a southerly facing window, with nothing obstructing its path to the sky.

37

38


Selecting XM Radio Channels

There are two modes for selecting XM radio channels:

Channel Search mode, which allows you to select any channel.

Category Search mode, which allows you to select channels by category.

1

3

RETURN

V1

1

4

CD

7

ON STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0

CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

ENTER VOL

-

PREV

CH

DISPLAY

RET

URN

SET

UP

MUTING

1

2

REC PLAYLIST

SP A SP B

LISTENING MODE

RANDOM

■ Channel Search Mode

1

RECEIVER

TUNER

9



[TUNER] INPUT SELECTOR button repeatedly to select XM.


2 Press the [MENU] button to select “Channel Search” mode.

■ Category Search Mode

1

RECEIVER

TUNER

9



[TUNER] INPUT SELECTOR button repeatedly to select XM.


2 Press the [MENU] button to select “Category Search” mode.

3

ENTER

Use the Left and Right [ ]/[ ] buttons to select a category, and use the Up and Down [ ]/[ ] buttons to select a channel in that category.

Note:

Channels cannot be selected while the is flashing, as tuning is in progress.

indicator

Selecting the Previous Channel:

To listen to the previously selected XM channel.

1

RECEIVER



[RETURN] button.

You can also use the AV receiver’s

[RETURN] button.

3 Use the Up and Down [ ]/[ ] buttons to select a channel.

ENTER

Channel number Channel name

You can also use the Left and Right

[ ]/[ ] buttons to select a category.

Note:

Channels cannot be selected while the is flashing, as tuning is in progress.

indicator


DISPLAY /

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

TUNER RETURN

Selecting XM Channels from the Front Panel:

1

TUNER

Press the [TUNER] input selector button repeatedly to select XM.


2

TUNING / PRESET

ENTER

Use the TUNING Up and Down

[ ]/[ ] buttons to select a channel.

In Channel Search mode, you can select any channel.

In Category Search mode, you can only select channels from the currently selected category.

RECEIVER

DISPLAY

- - / - - -

10 11

INPUT SELECTOR

MACRO

1 2 3

12

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV

DIMMER

VCR CABLE

CDR

HDD

SAT

MD

SLEEP

MEN

U

TO

P M

ENU

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

DISPLAY

RET

URN

SET

UP

MUTING

REC PLAYLIST RANDOM

SP A SP B

LISTENING MODE

SURR STEREO

REPEAT AUDIO SUBTITLE PLAY MODE

ALLST DIRECT

The following information can be displayed:

Channel name

Channel number

& preset number

Category

Artist

Song title

Displaying XM Radio Information

1

AV receiver

DISPLAY

On the AV receiver, press the

[DISPLAY] button repeatedly to cycle through the available information.

Listening mode

Note:

If the category, artist, or song title is not available, “- - -” will be displayed instead.


RECEIVER

On the remote controller, press the [RECEIVER] REMOTE MODE button, and then press the [DIS-

PLAY] button repeatedly.

DISPLAY

39

40


/ , ENTER

MASTER VOLUME

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

TAPE TUNER

RETURN SETUP

CD

VCR

VIDEO

VIDEO 3 INPUT

L AUDIO R

SETUP

Positioning the XM Antenna

You can check the signal strength of the XM radio signal and adjust the position of the XM antenna accordingly.

1

SETUP

On the AV receiver, press the

[SETUP] button.

XM Radio Messages

The following messages may appear while using XM radio.

The XM antenna is not connected properly. Check the antenna.

The XM user encryption code is being updated. Please wait.

2

TUNING / PRESET

ENTER

Use the Up and Down [ ]/[ ] buttons to select “5. XM Setup,” and then press the [ENTER] button.

The signal is too weak. Check the antenna connection and reposition it for the best reception.

3 Adjust the position of the XM antenna so that the signal strength is at least 70%.

The AV receiver is tuning or decoding audio or text data.

Please wait.

The signal level range is 0% to 100%.

Note:

If the signal level is 0%, make sure that the XM antenna is connected properly.

The XM channel you selected is not currently broadcasting. Select another channel.


Presetting AM/FM Stations &

XM Channels

2, 4 3

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN

TAPE TUNER CD

SETUP

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

You can store a combination of up to 30 of your favorite

AM/FM radio stations and XM channels as presets.

1 Tune into the AM/FM station or

XM channel that you want to store as a preset.

2

MEMORY

Press the [MEMORY] button.

The MEMORY indicator appears and the preset number flashes.

Selecting Presets

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TONE

MULTl CH DVD

1

+

1

ON STANDBY

DIMMER

TV

INPUT

V1

1

V2

2

V3

3 +

TUNING / PRESET

4

MULTI CH

5

DVD

6

TV CH

-

ENTER

CD TAPE TUNER

STEREO

VIDEO 1

VCR

LISTENING MODE

7


8

DIMMER

9

MEMORY TUNING MODE RETURN

TAPE

CLEAR

TV VOL

TUNER VIDEO 2

+10

VIDEO 3

0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

CD

SETUP

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV VCR

I

CABLE

CDR

SAT

MD

SLEEP

MEN

U

TO

P M

ENU

+

CH

DISC

ALBUM

PREV

CH

-

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

1

TUNING / PRESET

ENTER

REC PLAYLIST RANDOM

To select a preset, use the PRE-

SET [ ]/[ ] buttons, or the remote controller’s CH [+/–] button.

3

TUNING / PRESET

ENTER

While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 30.

4

MEMORY

+

CH

DISC

ALBUM

-

Press the [MEMORY] button again to store the station or channel.

The station or channel is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite AM/FM radio stations and XM channels.

Deleting Presets

2

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

1 Select the preset that you want to delete.

See the previous section.

2

MEMORY TUNING MODE

CLEAR

While holding down the [MEM-

ORY] button, press the

[TUNING MODE] button.

The preset is deleted and its number disappears from the display.

41

42

Common Functions

This chapter explains functions that can be used with any input source.

Adjusting the Bass & Treble

You can adjust the bass and treble for the front speakers

(except when the Direct listening mode is selected).

1

TONE

Press the AV receiver’s [TONE] button repeatedly to select either

Bass or Treble.

Press

[RECEIVER] first

DIMMER

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

PREV

CH

-

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

SLEEP

MUTING

CH SEL

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

LEVEL – +

2

+

Use the TONE [–]/[+] buttons to adjust.

■ Bass

You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.

■ Treble

You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps.

Note:

• To bypass the bass and treble tone circuits, select the

Direct listening mode.

TONE, –, +

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD

+ STEREO

VIDEO 1

LISTENING MODE

VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

MUTING

Press the remote controller’s

[MUTING] button.

The output is muted and the MUTING indicator flashes on the display.

PHONES DIMMER

Setting the Display Brightness

You can adjust the brightness of the display.

DIMMER


[DIMMER] button repeatedly to select: dim, dimmer, or normal brightness.

Alternatively, you can use the AV receiver’s [DIMMER] button.

To unmute the AV receiver, press the remote controller’s [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off.

Muting is cancelled when the AV receiver is set to

Standby.

Common Functions—Continued

Using the Sleep Timer

With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period.

SLEEP


[SLEEP] button repeatedly to select the required sleep time.

You can set the sleep time from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.

SLEEP indicator

Adjusting Speaker Levels

You can adjust the volume of each speaker in speaker set

A. These temporary adjustments are cancelled when the

AV receiver is set to Standby.

1

LEVEL

CH SEL

LEVEL

Use the remote controller’s

[CH SEL] button to select each speaker, and use the [LEVEL–] and [LEVEL+] buttons to adjust the volume.

You can adjust the volume of each speaker from –12 dB to +12 dB

(–15 dB to +12 dB for the subwoofer).

To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears.

To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.

Using Headphones

For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s

PHONES jack.

STANDBY/ON

A SPEAKERS B

PHONES

Notes:

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to No or None in the Speaker

Configuration cannot be adjusted.

■ Speaker Set B

While speaker set B is on, you can adjust the volume of the left and right speakers, from –12 dB to +12 dB.

• These settings are stored when the AV receiver is set to Standby.

• While speaker set B is on, you cannot adjust the levels of speaker set A’s surround back speakers.

■ Headphones

While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from –12 dB to

+12 dB each.

Notes:

• Always turn down the volume before connecting your headphones.

• Speaker sets A and B are turned off while the headphones plug is inserted in the PHONES jack.

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it was set to Mono, Stereo, or Direct, in which case it stays the same.

• When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones.


■ Multichannel DVD Input

While the multichannel DVD input is selected, you can adjust the level of each channel, from –12 dB to +12 dB.

(–30 to +12 dB for the subwoofer.)


• Individual speaker levels can also be adjusted in

“3. MultiLevel” (see page 53).

43

44

Using the Listening Modes

Selecting the Listening Modes

For a description of each listening mode, see “About the

Listening Modes” on page 46.

• The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial or optical).

• Listening mode availability depends on the format of the current input signal.

• While a pair of headphones is connected, you can only select the Mono, Direct, or Stereo listening mode.

Selecting with the Remote Controller

CDR

DIMMER

TO

P M

ENU MEN

U

+

CH

DISC

ALBUM

PREV

CH

-

DISPLAY

RE

TURN

ENTER

SET

UP

MD

SLEEP

VOL

MUTING

SURR

STEREO

DIRECT

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

,

ALL ST

Selecting on the AV receiver

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

TAPE TUNER

RETURN SETUP

CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

STEREO

LISTENING MODE

■ [STEREO] button


■ LISTENING MODE [ ]/[ ] buttons

Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the current input source.

■ [SURR] button

This button selects the Dolby Digital and DTS listening modes.

■ [STEREO] button


■ [DIRECT] button

This button selects the Direct listening mode.

■ LISTENING MODE [ ]/[ ] buttons

Pressing these buttons repeatedly cycles through all of the listening modes that can be used with the current input source.

■ [ALL ST] button

This button selects the All Channel Stereo listening mode.

Using the Listening Modes—Continued

The following table shows which listening modes can be used with each input signal format.

Source Format Analog,

PCM

*1 3/2.1

2/2.1

Dolby D

2/0

(Stereo)

1/0,1+1 Other 3/2.1

DTS/DTS 96/24

*2

2/0

(Stereo)

DTS-ES

Discrete Matrix

Multich

Listening mode

Direct

Stereo

Mono

Multich

PLIIx Movie/Music/Game

*3

Neo:6 Cinema

Neo:6 Music

*4

Dolby D

Dolby D EX

Dolby D+PLIIx Music

Dolby D+PLIIx Movie

DTS, DTS 96/24

CD, TV, VHS,

MD, turntable, radio, cassette,

DTV, etc.

✔

✔

✔

✔

✔

✔

✔

✔

DVD, DTV, etc.

✔

✔

✔

✔

✔

✔

✔

✔

✔

✔

DVD, CD, etc.

✔

✔

✔

✔

✔

DVD

✔

✔

✔ ✔ *5

DTS-ES Discrete

Onkyo

Original

DSP

DTS-ES Matrix

DTS+Neo:6

DTS+Dolby EX

DTS+PLIIx Music

DTS+PLIIx Movie

Mono Movie

Orchestra

Unplugged

Studio-Mix

TV Logic

All Ch Stereo

Full Mono

*4

✔ ✔ ✔ ✔ ✔

✔

✔

✔ ✔

✔

✔

✔

*1. In the Direct listening mode, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.2 kHz, and 96 kHz respectively. For listening modes other than Direct and Stereo, 96 kHz signals are processed at 48 kHz.

*2. In the Direct, Stereo, and DTS 96/24 listening modes, signals are processed as DTS 96/24. Everything else is processed as DTS.

*3. If the Surr Back parameter is set to None, or speaker set B is on, PLII is used.

*4. Available only when Surround speakers are connected.

*5. If the Surr Back setting is set to None, or speaker set B is on, DTS is used.

: Not available when the Surr Back parameter is set to None, or while speaker set B is on.

: Not available when the Surr Back parameter is set to None or 1ch, or while speaker set B is on.

Tip: To check the format of the digital input signal, see “Displaying Source Information” on page 35.

45


46

About the Listening Modes

With its surround-sound decoders and DSP modes, the

AV receiver can transform your home listening room into a movie theater or concert hall.

The AV receiver’s surround indicators show which speakers are active in each listening mode.

Front left Center Front right

Subwoofer

Surround left

Surround back left/ right

Surround right

Direct

In this mode, the input source is output as it is, with minimal processing for a faithful sound. The bass and treble functions are bypassed.

Stereo

In this mode, the input source is output by the front left and right speakers and subwoofer.

Mono

Use this mode when watching an old movie with a mono soundtrack, or to select the foreign language soundtracks recorded in the left and right channels of some movies.

It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

Dolby Pro Logic II Movie

Use this mode with DVDs and videos that bear the Dolby Surround logo, or TV shows that feature Dolby Surround. You can also use it to create 5.1 surround from stereo movies and

TV shows.

Dolby Pro Logic II Music

Use this mode to create 5.1 surround from stereo music sources, such as CDs and DVDs.

Dolby Pro Logic IIx

If you’ve connected surround back speakers to the AV receiver, Dolby Pro Logic IIx can create 7.1 surround from stereo music or 5.1 movies. Dolby Pro Logic IIx offers a well defined, natural multichannel surroundsound experience, putting the listener in a seamless envelope of sound. The added drama and natural sound enhances the listening experience with music, movies, and games.

Dolby Pro Logic IIx has three modes of operation: Movie

mode for watching movies, Music mode for listening to music, and Game mode for playing games on a games console with stereo outputs.

Dolby Digital

With Dolby Digital, you can experience the same thrilling sound that you get at a movie theater or concert hall. Use this mode with DVDs that bear the Dolby Digital logo.

Dolby Digital EX

Dolby Digital EX includes a surroundback channel, for 6.1 surround. It offers a heightened sense of space, and added realism with moving sounds, especially those that move

360 degrees or fly overhead. Dolby Digital EX can also be enjoyed on a 5.1 system, in which case the surroundback channel sound is split between the surround left and surround right speakers. Use this mode with DVDs that feature 5.1 and bear the Dolby Digital logo.

DTS

This format offers a surround sound experience with exceptional fidelity. It offers six discrete channels for 5.1 surround, and uses less compression for a truly faithful sound.

You’ll need a DTS-capable DVD player to enjoy DTS material. Use this mode with DVDs and CDs that bear the DTS logo.

DTS 96/24

This mode offers very high audio quality.

Use it with CDs and DVDs that bear the

DTS 96/24 logo.

DTS-ES Discrete

This is DTS with an added surround back channel for 6.1 surround. With the additional surround back channel, it offers seven independent digital channels, providing a real sense of movement and space. Use it with CDs and DVDs that feature DTS 6.1 and bear the DTS-ES logo.

DTS-ES Matrix

This is DTS with a surround back channel for 6.1 surround. Use it to create 6.1 surround from DTS 5.1 material. Since DTS 5.1 material already contains surround back channel information, the back channel can be reconstructed for real 6.1 surround.

Use this mode with CDs and DVDs that bear the DTS-

ES.

Neo:6

This mode creates 6.1 surround from stereo sources. It offers six full-bandwidth channels and excellent separation. There are two modes of operation: Cinema mode for watching movies, and Music mode for listening to music.

Cinema mode simulates the realistic sense of movement that you get with 6.1 surround. Use it with videos,

DVDs, and TV shows that feature stereo sound.

Music mode uses the surround channels to simulate a natural sound field, something that cannot be done with conventional stereo. Use it with stereo sources and music

CDs.


Onkyo Original DSP Modes

Mono Movie

Suitable for old movies and other mono sources. The center speaker outputs the sound as it is, while reverb is applied to the sound output by the other speakers, providing presence.

Orchestra

Suitable for classical or operatic music. The surround channels are emphasized in order to widen the stereo image. In addition, it simulates the natural reverberation of a large hall.

Unplugged

Suitable for acoustic instrument sounds, vocals, and jazz music. By emphasizing the front stereo image, it simulates the experience of being right in front of the stage.

Studio-Mix

Suitable for rock and pop music. Listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

TV Logic

Adds realistic acoustics to TV shows produced in a TV studio. In addition, it adds surround effects to the entire sound and adds clarity to voices.

All Ch Stereo

Ideal for background music. The front, surround, and surround back channels create a stereo image that fills the entire listening area.

Full Mono

All speakers output mono audio, so the music sounds the same regardless of where you are.

47


RECEIVER

ENTER

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

PREV

CH

-

RE

TURN

ENTER

SET

UP

VOL

DISPLAY MUTING

SETUP

Using the CinemaFILTER

With the CinemaFILTER, you can soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater.

CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Pro

Logic II Movie, Dolby Pro Logic IIx Movie, DTS,

DTS-ES, DTS Neo:6 Cinema, DTS 96/24, DTS+Neo:6, and DTS+Dolby EX.

1

RECEIVER

CINE FLTR



[CINE FLTR] button repeatedly to select:

On: CinemaFILTER on.

Off: CinemaFILTER off.

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

CINE

FLTR

L NIGHT

Using the Audio Adjust Settings

The Audio Adjust settings only affect speaker set A.

1

RECEIVER



[SETUP] button.

48

Using the Late Night Function

(Dolby Digital only)

With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

1

RECEIVER

L NIGHT



[L NIGHT] button repeatedly to select:

Off: Late Night function off.

Low: Small reduction in dynamic range.

High: Big reduction in dynamic range.

Notes:

• The effect of the Late Night function depends on the

Dolby Digital material that you are playing, and with some material there will be little or no effect.

• The Late Night function is set to Off when the AV receiver is set to Standby.

2

ENTER

ENTER

Use the Up and Down [ ]/[ ] buttons to select “4. Audio

Adjust,” and then press the

[ENTER] button.

4

5


3

ENTER

Use the Left and Right [ ]/[ ] buttons to change the setting.

Press the Down [ ] button to select the next setting.

ENTER

Repeat step 3 for the other settings.


Setup closes.

The Audio Adjust settings are explained below.

Input Channel Settings

■ Multiplex

This setting determines which channel is output from a stereo multiplex source. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

Main: The main channel is output (default).

Sub: The sub channel is output.

M/S: Both the main and sub channels are output.

■ Mono (2ch)

This setting determines which channel is output when the Mono listening mode is used with a stereo source.

L+R: Both the left and right channels are output

(default).

L: Only the left channel is output.

R: Only the right channel is output.

PL II & PL IIx Music Mode Settings

These settings apply to only 2-channel (stereo) sources.

■ Panorama

With this setting, you can broaden the width of the front stereo image when using the Pro Logic II Music or Pro

Logic IIx Music listening mode.

On: Panorama function on.

Off: Panorama function off (default).

■ Dimension

With this setting, you can move the sound field forward or backward when using the Pro Logic II Music or Pro

Logic IIx Music listening mode. The default value is 3.

Higher settings move the sound field forward. Lower settings move it backward.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

■ Center Width

With this setting, you can adjust the width of the sound from the center speaker when using the Pro Logic II

Music or Pro Logic IIx Music listening mode. Normally, the center channel sound is output by only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center.) This setting adjusts the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. It can be adjusted from 0 to 7 (default value is 3).

DTS Neo:6 Music Mode Setting

■ Center Image

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel (stereo) sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. It can be adjusted from 0 to 5 (default value is 3). This setting is unavailable if no surround speakers are connected.

When set to 0, the front left and right channel output is attenuated by half (–6 dB), giving the impression that the sound is located centrally. This setting works well when the listening position is considerably off center. When set to 5, the front left and right channels are not attenuated, maintaining the original stereo balance.

Dolby Digital EX Input Signal Setting

■ Dolby D EX

This setting determines how Dolby Digital EX signals are handled. This setting is unavailable if no surround back speakers are connected or speaker set B is on.

Auto: If the source signal contains a Dolby Digital

EX flag, the Dolby Digital EX listening mode is used (default).

Manual: You can select Pro Logic IIx Movie, Pro

Logic IIx Music, Dolby Digital, or Dolby

Digital EX.

49

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources.

Recording the Input Source

You can only record to a component that is connected to the TAPE OUT or VIDEO 1 OUT jacks.

See pages 20–29 for information on connecting your AV components.

1

DVD

VIDEO 3

CD

VIDEO 1

VCR

TAPE

V1

1

CD

7


V2

2

TAPE

8

V3

3

DVD

6

TUNER

9

VIDEO 2

TUNER

Use the input selector buttons to select the component that you want to record.

Audio signals from the selected input source are output by the TAPE OUT and VIDEO 1 OUT jacks.

You can listen to the source while recording. The AV receiver’s VOL-

UME control has no effect on recording.

Recording from Different Sources

You can overdub audio onto your video recordings by recording from different audio and video sources. This is possible because only the audio source is changed when an audio-only input source, such as TAPE, TUNER, or

CD is selected. The video source is unchanged. For example, if you select the VIDEO 3 input source, followed by the CD input source, you can watch video from the VIDEO 3 input and listen to audio from the CD input.

In the following example, audio from the CD player connected to the CD IN jacks, and video from the camcorder connected to the VIDEO 3 INPUT VIDEO jack are recorded by the VCR connected to the VIDEO 1 OUT jacks.

VIDEO

VIDEO 3 INPUT

L AUDIO R

Camcorder video signal audio signal

50

2

3

On your recorder, start recording.

Start playback on the source component.

Notes:

• You cannot record from a component that’s connected to a digital input. Only analog inputs can be recorded.

• The surround sound effects provided by the listening modes cannot be recorded.

• You cannot record from an component that is connected to the multichannel DVD input.

• If you select another input source while recording, that input source will be recorded instead.

CD player VCR

1. Prepare the camcorder and CD player for playback.

2. Prepare the VCR for recording.

3. Press the [VIDEO 3] input selector button.

4. Press the [CD] input selector button.

This selects the CD player as the audio source, but leaves the camcorder as the video source.

5. Start recording on the VCR, then start playback on the camcorder and CD player.

Video from the camcorder and audio from the CD player are recorded by the VCR.

Advanced Setup

Advanced Speaker Settings

The advanced speaker settings cannot be changed while headphones are connected, speaker set B is on, or the multichannel DVD input is selected.

Crossover Frequency

To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your subwoofer and other speakers.

1

RECEIVER



[SETUP] button.

2

3

ENTER

ENTER

ENTER

ENTER

Use the Up and Down [ ]/[ ] buttons to select “1. Speaker

Config,” and then press the

[ENTER] button.

Use the Down [ ] button to select “Crossover,” and then use the Left and Right [ ]/[ ] buttons to select a crossover frequency.

Choose a crossover frequency suitable for your setup.

If you’re using a subwoofer, choose a crossover frequency based on the diameter of your front speakers.

If you’re not using a subwoofer, use the diameter of the first speaker that you specified as Small in steps 4 through 7 of the Speaker Configuration on page 32.

Speaker cone diameter

Over 8 in.

(20 cm)

6-1/2 to 8 in.

(16–20 cm)

5-1/4 to 6-1/2 in.

(13–16 cm)

3-1/2 to 5-1/4 in.

(9–13 cm)

Under 3-1/2 in.

(9 cm)

Crossover frequency

60Hz

80Hz

100Hz (default)

120Hz

150Hz

Continue with step 4, “Double Bass.”

Note:

• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly. In addition, listen to some music that you know well and choose a higher crossover frequency if you think there’s not enough sound coming from the subwoofer; a lower setting if you think there’s too much.

Double Bass

With the Double Bass function, you can boost bass output by feeding bass sounds from the front left and right channels to the subwoofer. This function can only be set if in the Speaker Configuration on page 32, the Subwoofer setting is set to Yes (step 3), and the Front setting is set to Large (step 4).

4

ENTER

ENTER

Use the Down [ ] button to select “Double Bass,” and then use the Left and Right [ ]/[ ] buttons to select:

On: Double Bass function on.

Bass from the front left and right channels is also fed to the subwoofer (default).

Off: Double Bass function off.

5 Press the [SETUP] button.

Setup closes.

51

52

Advanced Setup—Continued

Speaker Distance

To get the best from surround sound, it’s important that the sound from each speaker reaches the listener at the same time. To achieve this, you need to specify the distance from each speaker to the listening position.

1 Measure and make a note of the distance from each speaker to the listening position.

2

RECEIVER



[SETUP] button.

Notes:

• The Center and Subwoofer distances can be set up to

5 ft. (1.5 m) more or less than the Front distance. For example, if the Front distance is set to 20 ft. (6 m), the

Center and Subwoofer distances can be set between 15 and 25 ft. (4.5 and 7.5 m).

• The Surround and Surround Back distances can be set up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the

Front distance. For example, if the Front distance is set to 20 ft. (6 m), the SurrRight, Surr Left, Surr Back R, and Surr Back L distances can be set between 5 and 25 ft. (1.5 and 7.5 m).

3

Speaker Levels

You can set the volume level of each speaker so that all speakers can be heard equally at the listening position.

Speaker levels cannot be adjusted while the

AV receiver is muted.

ENTER

Use the Up and Down [ ]/[ ] buttons to select “2. Sp Distance,” and then press the

[ENTER] button.

1

RECEIVER



[SETUP] button.

ENTER

4

5

ENTER

ENTER

While “Unit” is displayed, use the

Left and Right [ ]/[ ] buttons to select “feet” or “meters”.

feet: Distances can be set in feet.

Range: 1 to 30 feet in 1-foot steps.

meters: Distances can be set in meters. Range: 0.3 to 9 meters in 0.3-meter steps.

Use the Down [ ] button to select a speaker, and use the Left and Right [ ]/[ ] buttons to specify the distance.

2

3

ENTER

ENTER

Use the Up and Down [ ]/[ ] buttons to select “3. Level Cal,” and then press the [ENTER] button.

A pink noise test tone is output by the front left speaker.

Turn up the volume so that you can hear the test tone sufficiently.

As each speaker outputs the test tone, its name appears on the display.

6

7

Repeat step 5 for all speakers.

Note:

Speakers that you set to No or None in the Speaker Configuration (page 32) cannot be selected.


Setup closes.

Advanced Setup—Continued

4

ENTER

ENTER

Use the Left and Right [ ]/[ ] buttons to adjust the speaker level, and use the Down [ ] button to select the next speaker.

The levels can be adjusted from –12 to

+12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

5

6

Repeat step 4 so that the level of the test tone coming from each speaker is the same.

Speakers that you set to No or None in the Speaker Configuration (page 32) do not output the test tone.


Setup closes.

Don’t forget to turn down the volume if you turned it up while setting the levels.

Notes:

• A quick way to adjust the speaker levels is to press the remote controller’s [TEST TONE] button to turn on the test tone. Use the [LEVEL–] and [LEVEL+] buttons to adjust the levels, and use the [CH SEL] button to select the speakers.

• If the multichannel DVD input is selected (page 35), in step 2, “3. MultiLevel” appears instead of “3. Level

Cal,” and you can adjust the level of each channel of the multichannel DVD input. These level settings are independent of the Speaker Configuration settings on page 32.

Digital Signal Formats

The following table shows the display indicator for each digital signal format.

Display Format

Dolby Digital

DTS

PCM PCM

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS:

• If the beginnings of tracks from a PCM source are cut off, try the PCM setting.

• If noise is produced when fast forwarding or reversing a DTS CD, try the DTS setting.

STANDBY/ON

A SPEAKERS B

PHONES

STANDBY

TUNING / PRESET

ENTER

TONE

MULTl CH DVD


VIDEO 1 VIDEO 2


VIDEO 3


CLEAR

RETURN SETUP

TAPE TUNER CD

VCR

MASTER VOLUME

VIDEO

VIDEO 3 INPUT

L AUDIO R

DIGITAL INPUT

1 Press and hold the AV receiver’s [DIGITAL

INPUT] button for about 3 seconds.

2 While “Auto” is displayed (about 3 seconds), press the [DIGITAL INPUT] button repeatedly to select: PCM, DTS, or Auto.

PCM: The PCM indicator flashes, and only input signals in PCM format will be output.

DTS: The DTS indicator flashes, and only input signals in DTS format will be output.

Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

53

54

Controlling Other Components

You can use the AV receiver’s remote controller

(RC-632M) to control your other AV components, including those made by other manufacturers.

This section explains how to:

• Enter the remote control code for a component that you want to control (e.g., DVD, TV, VCR).

• Learn commands directly from another component’s remote controller (see page 57).

• Program the MACRO buttons to perform a sequence of up to eight actions (see page 58).

2

REMOTE MODE

CD DVD

TV

CABLE

CDR

VCR

SAT

MD

STANDBY

While holding down the REMOTE

MODE button that you want to set, press the [STANDBY] button.

The Remote indicator lights up.

Entering Remote Control Codes

Entering a remote control code for a REMOTE MODE button allows you to control an other component with the remote controller. You’ll need to enter a code for each component that you want to control.

STANDBY

Remote indicator

TV I

Number buttons

RECEIVER

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU MEN

U

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

DISPLAY

RE

TURN

SET

UP

MUTING

REMOTE

MODE

1

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

Look up the appropriate remote control code in the Remote Control Codes list.

The codes are organized by category.

3

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

Within 30 seconds, use the number buttons to enter the 4-digit remote control code.

The Remote indicator flashes twice.

0

11

4 Press the REMOTE MODE button again to select the remote controller mode, point the remote controller at the component, and operate it.

If the remote controller doesn’t work as expected, and several remote codes are listed, try each one in turn and use the one that works best.

Notes:

• Remote control codes cannot be entered for the

[RECEIVER] and [HDD] REMOTE MODE buttons.

• The remote control codes provided are correct at the time of printing, but are subject to change.

• The HDD remote mode can only be used with the

Onkyo DS-A1 Remote Interactive Dock at this time.

• The [DVD] and [CD] REMOTE MODE buttons are preprogrammed for use with Onkyo DVD players and CD players respectively.

* To control another manufacturer’s CD recorder or

MD recorder, enter the appropriate control code to the [CD] REMOTE MODE button.

Controlling Other Components—Continued

Remote Control Codes for Onkyo

Components Connected via

Onkyo components that are connected via are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

1 Make sure the Onkyo component is connected with an cable and an analog audio cable (RCA).

See page 29 for details.

2 Enter the appropriate remote control code for the REMOTE MODE button.

• [DVD] REMOTE MODE button

5002: Onkyo DVD player with

• [CD] REMOTE MODE button

6002: Onkyo CD player with

• [MD] REMOTE MODE button

6008: Onkyo MD recorder with

• [CDR] REMOTE MODE button

6006: Onkyo CD recorder with

See the previous page for how to enter remote control codes.

3 Press the REMOTE MODE button, point the remote controller at the AV receiver, and operate the component.

If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an Onkyo component that’s not connected via , use the following remote control codes:

• [DVD] REMOTE MODE button

5001: Onkyo DVD player without (default)

• [CD] REMOTE MODE button

6001: Onkyo CD player without (default)

• [MD] REMOTE MODE button

6007: Onkyo MD recorder without

• [CDR] REMOTE MODE button

6005: Onkyo CD recorder without

Note:

If you connect an -capable Onkyo MiniDisc or CD recorder to the TAPE IN/OUT jacks, for remote operation to work properly, you must set the display to MD or

CDR (see page 31).

Resetting the REMOTE MODE Buttons

You can reset a REMOTE MODE button to its default remote control code.

1

REMOTE MODE

CD DVD

TV

CABLE

CDR

VCR

SAT

MD


MODE button that you want to reset, press the TV [ ] button.

The Remote indicator flashes three times.

2

REMOTE MODE

CD DVD

TV

CABLE

CDR

VCR

SAT

MD

Press the REMOTE MODE button again.

The Remote indicator flashes twice, indicating that the button has been reset.

The [DVD] and [CD] REMOTE

MODE buttons are preprogrammed with remote control codes for controlling Onkyo DVD players and CD players respectively. When these buttons are reset, the preprogrammed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

1

2

RECEIVER

STANDBY

RECEIVER

While holding down the

[RECEIVER] REMOTE MODE button, press the [STANDBY] button.

The Remote indicator flashes five times.


MODE button again.

The Remote indicator flashes twice, indicating that the remote controller has been reset.

55

56


To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote control mode first.) With some AV components, certain buttons may not work as expected, and some may not work at all.

■ Controlling a TV

Press [TV] first

■ Controlling a VCR

Press [VCR] first

■ Controlling a Satellite or

Cable Receiver

Press [SAT] or [CABLE] first

A

2

8

3

4

8

ON

V1

1

4

CD

7

STANDBY

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

ENTER VOL

PREV

CH

-

DISPLAY

RET

URN

SET

UP

MUTING

5

3

6

8

8

7

A

2

3

9

4

5

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10 0

CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV

DIMMER

VCR CABLE

CDR

TV VOL

HDD

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

DISPLAY

RET

URN

SET

UP

MUTING

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

6

7

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

A [ON], [STANDBY], TV [

Sets the TV to On or Standby.

B Number buttons

Enter numbers.

C [CH +/–], TV CH [+]/[–]*

Selects channels on the TV.

D [PREV CH]

Selects the previous channel.

E [TV INPUT]*

]*

Selects the TV’s external inputs.

F TV VOL [ ]/[ ]*

Adjusts the TV’s volume.

G [MUTING]

Mutes the TV.

H [ ]/[ ]/[ ]/[ ]/[MENU]/

[ENTER]/[RETURN]

Navigate menus on the TV.

* Buttons marked with an asterisk

(*) are exclusively for controlling a TV and can be used at anytime regardless of the current remote controller mode.

A [ON], [STANDBY]

Sets the VCR to On or Standby.


Select channels.

C [CLEAR]

Cancels functions.

D [CH +/–]

Selects channels on the VCR.

E [PREV CH]


F REC [ ]

Starts recording.

G Eject [ ]

Ejects the videocassette.

H [ ], [ ], [ ], [ ], [ ]

Play, Pause, Stop, Rewind, and

Fast forward.

I [ ]/[ ]/[ ]/[ ]/[MENU]/


Navigate menus on the VCR.

9

9

9

8

A

2

3

8

4

5

8

+

CH

DISC

ALBUM

-

PREV

CH

DISPLAY

ON STANDBY

I

TV

INPUT

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

V3

3

DVD

6

TUNER

9

+

TV CH

-

+10

0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

MACRO

1 2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD

TV VOL

HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

ENU

MEN

U

RET

URN

ENTER

SET

UP

VOL

MUTING

REC PLAYLIST RANDOM

STEREO

REPEAT

SP A SP B

LISTENING MODE

SURR

AUDIO

DIRECT

SUBTITLE PLAY MODE

ALLST

TEST TONE CH SEL


LEVEL

L NIGHT

LEVEL

CINE FLTR

RC-632M

A [ON], [STANDBY]

Sets the satellite/cable receiver to On or Standby.


Enter numbers.

C [CLEAR]

Cancels functions.

D [CH +/–]

Selects satellite/cable channels.

E [PREV CH]


F [GUIDE]

Displays the program guide.

G [ ], [ ]

Rewind, and Fast forward.

H [ ]/[ ]/[ ]/[ ]/[MENU]/


Navigate menus on the satellite/cable receiver.

8

8

6

7


Learning Commands from Other

Remote Controllers

The AV receiver’s remote controller can receive and learn commands from other remote controllers. By transmitting, for example, the Play command from your CD player’s remote controller, the remote controller can learn it and then transmit the exact same command when its Play [ ] button is pressed in CD mode.

You can also use this function to learn individual commands after entering a remote controller code (page 54).

1

1, 4

ON STANDBY

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU

MEN

U

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

DISPLAY

RE

TURN

SET

UP

MUTING

1

REMOTE MODE

DVD RECEIVER

TAPE/AMP

CD HDD

TV

CABLE

CDR

ON

VCR

SAT

MD



MODE button for the mode in which you want to use the command, press the [ON] button.


3 Point the remote controllers at each other, about 2 to 6 inches

(5–15 cm) apart, and then press and hold the button whose command you want to learn until the

Remote indicator flashes.

If the command is learned successfully, the Remote indicator flashes twice.

About 2 to 6 inches (5–15 cm)

I-CH PU

ULT

D

PR

ME

DI

TO

PH

EC

EL

IN PE

VD

PO

EO

D DIS

EL

ME

LU

TIN

ER

VCR

1

V1

STA

NDBY

1

DVD

--/--0

INP 10

2

0

ELE

CT

O

11

R

3

7

CD

4

8

CLEAR

12

V2

TAPE

5

MU

LTI CH

2

9

NE

R

6

DVD

3

V3

-

TV C

H

+

TV VO

L

CD

O

N

CDR

CABLE

HDD

MD

SAT

TV

INPUT

RC-632M

4 To learn more commands, repeat steps 2 and 3.

Press any REMOTE MODE button when you’ve finished.

Notes:

• The following buttons cannot learn new commands:

REMOTE MODE, MACRO [1], [2], [3], TV [ ],

TV CH [+]/[–], [TV INPUT], TV VOL [ ]/[ ].

• The AV receiver’s remote controller can learn approximately 70–90 commands, although, this will be reduced by commands that use a lot of memory.

• Remote controller buttons such as Play, Stop, Pause, and so on are preprogrammed with commands for controlling Onkyo CD players, cassette decks, and

DVD players. However, they can learn new commands, and you can restore the preprogrammed commands by resetting the remote controller (page 55).

• To overwrite a previously learned command, repeat this procedure.

• Only commands from infrared remote controllers can be learned.

• When the remote controller’s batteries expire, all learned commands will be lost and will have to be learned all over again, so don’t discard your other remote controllers.

2 On the AV receiver’s remote controller, press the button you want to learn the new command.

57

58


Using Macros

You can program the remote controller’s MACRO buttons to perform a sequence of actions.

Example:

To play a CD, you typically need to perform the following actions:

1. Press the [RECEIVER] REMOTE MODE button to select Receiver mode.

2. Press the [ON] button to turn on the AV receiver.

3. Press the [CD] INPUT SELECTOR button to select the CD input source.

4. Press the REMOTE MODE [CD] button to select the CD remote controller mode.

5. Press the Play [ ] button to start playback on the

CD player.

You can program a MACRO button to perform all five actions.

Making Macros

You can make one macro for each MACRO button, and each macro can perform up to eight actions.


1, 3

1

ON STANDBY

V1

1

4

CD

7

V2

2

MULTI CH

5

TAPE

8

I

V3

3

DVD

6

TUNER

9

TV

INPUT

+

TV CH

-

TV VOL

+10 0 CLEAR

- - / - - -

10 11

INPUT SELECTOR

12

1

MACRO

2 3

RECEIVER

TAPE/AMP

REMOTE MODE

DVD CD HDD

TV

DIMMER

VCR CABLE

CDR

SAT

MD

SLEEP

TO

P M

ENU MEN

U

+

CH

DISC

ALBUM

-

ENTER VOL

PREV

CH

DISPLAY

RE

TURN

SET

UP

MUTING

1

REMOTE MODE

DVD RECEIVER

TAPE/AMP

CD HDD

TV

CABLE

CDR

VCR

SAT

MD


MODE button for the mode you want to start with, press MACRO button [1], [2], or [3].


For the CD example in the left column, you’d press and hold the [RECEIVER]

REMOTE MODE button, and then press MACRO button [1], [2], or [3].

2

3

On the remote controller, press the buttons whose actions you want to program into the macro in the order you want them performed.

For the CD example in the left column, you’d press the following buttons:

[ON], INPUT SELECTOR [CD],

REMOTE MODE [CD], Play [ ].

When you’ve finished, press the

MACRO button again.

The Remote indicator flashes twice.

If you enter all eight actions, the process will finish automatically.

Notes:

• If one or more of the buttons you used to make the macro are taught new commands, the macro will no longer work properly and will have to be made again.

Running Macros

1 Press the MACRO [1], [2], or [3] button.

The actions in the macro are performed in the order in which they were programmed. Keep the remote controller pointed at the AV receiver until all of the commands have been transmitted.

Macros can be run at anytime regardless of the current remote controller mode.

Deleting Macros

1 While holding down the [RECEIVER]

REMOTE MODE button, press the MACRO button whose macro you want to delete.

2 Press the MACRO button again.

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer.

Power

Can’t turn on the AV receiver

• Make sure that the power cord is plugged into the wall outlet properly.

• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned on

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer.

Audio

There’s no sound or it’s very quiet

• Make sure that the digital input source is selected properly (page 31). Press the [DIGITAL INPUT] button repeatedly.

• Make sure that all audio connecting plugs are pushed in all the way (page 20).

• Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with metal part of each speaker terminal (page 17)

• Make sure that the speaker cables are not shorting.

• Check the volume. It can be set to MIN, 1 through 79, or MAX (page 34). The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment.

• If the MUTING indicator is shown on the display, press the remote controller’s [MUTING] button to unmute the AV receiver (page 42).

• While a pair of headphones is connected to the

PHONES jack, no sound is output by the speakers

(page 43).

• Check the digital audio output settings on the connected device. On some games consoles, such as those that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an audio format from a menu.

• If your turntable doesn’t have a phono preamp built-in, you must connect one between it and the AV receiver.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer and phono preamp.

• Specify the speaker distances and adjust the individual speaker levels (pages 52, 53).

• The input signal format is set to PCM or DTS. Set it to

Auto (page 53).

Only the front speakers produce sound

• When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

• Make sure the speakers are configured correctly

(page 32).

Only the center speaker produces sound

• If you use the Pro Logic IIx Movie or Pro Logic IIx

Music listening mode with a mono source, such as an

AM radio station or mono TV program, the sound is concentrated in the center speaker.


(page 32).

The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected, the surround speakers produce no sound (page 44).

• Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.


(page 32).

The center speaker produces no sound

• When the Stereo or Mono listening mode is selected, the center speaker produces no sound (page 44).


(page 32).

The surround back speakers produce no sound

• The surround back speakers are not used with all listening modes. Select another listening mode

(page 44).

• Not much sound may be produced by the surround back speakers with some sources.


(page 32).

• While speaker set B is on, speaker set A is reduced to

5.1-channel playback and the surround back speakers produce no sound.

59

60

Troubleshooting—Continued

The subwoofer produces no sound

• The subwoofer outputs no sound while only speaker set B is on. Turn on speaker set A.

• When you play source material that contains no information in the LFE channel, the subwoofer produces no sound.


(page 32).

Speaker set B produces no sound

• Speaker set B only outputs sources that are connected to an analog input. Make sure that the analog audio cables are connected properly.

There’s no sound with a certain signal format

• Check the digital audio output setting on the connected device. On some games consoles, such as those that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an audio output format from a menu.

Can’t get 6.1- or 7.1-channel playback

• While speaker B is on, speaker set A is reduced to

5.1-channel playback.

The volume cannot be set to 79

• When the volume level of each speaker has been adjusted (pages 43, 52), the maximum possible volume setting may be reduced.

Noise can be heard

• Using cable ties to bundle audio cables with power cords, speaker cables, and so on may degrade the audio performance, so don’t do it.

• An audio cable may be picking up interference. Try repositioning your cables.

The Late Night function doesn’t work

• Make sure the source material is Dolby Digital

(page 48).

The multichannel DVD input doesn’t work

• Check the multichannel DVD input connections

(page 23).

• To select the multichannel DVD input, press the

[MULTI CH] input selector button.

• Check the audio output settings on your DVD player.

About DTS signals

• When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about 3 seconds, and then resume playback.

• With some CD players, you won’t be able to playback

DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

• When playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

Video

There’s no picture

• Make sure that all video connecting plugs are pushed in all the way (page 20).

• Make sure that each video component is properly connected.

• The AV receiver does not convert between formats, so if a video source component is connected to a component video input, your TV must be connected to the component video output (page 21).

• On your TV, make sure that the video input to which the AV receiver is connected is selected.

Tuner

Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn’t appear

• Relocate your antenna.

• Move the AV receiver away from your TV or computer.

• Listen to the station in mono (page 36).

• When listening to an AM station, operating the remote controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor antenna.

Can’t select XM radio channels

• Channels cannot be selected while the tor is flashing, as tuning is in progress.

indica-

Troubleshooting—Continued

Remote Controller

The remote controller doesn’t work

• Make sure that the batteries are installed with the correct polarity (page 9).

• Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor (page 9).

• Make sure you’ve selected the correct remote controller mode (page 10).

• Make sure you’ve entered the correct remote control code (page 54).

Can’t control other components

• Make sure you’ve selected the correct remote controller mode (page 10).

• If you’ve connected an -capable Onkyo MD recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT jacks, or a

DS-A1 Remote Interactive Dock to the VIDEO 2 IN jacks, for the remote controller to work properly, you must set the display to MD, CDR, or HDD (see page 31).

• The wrong remote control code has been entered.

• The entered remote control code may not be correct. If more than one code is listed, try each one.

• With some AV components, certain buttons may not work as expected, and some may not work at all.

• To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first

(see page 55).

• To control an Onkyo component that’s not connected via , or another manufacturer’s component, point the remote controller at the component. Be sure to enter the appropriate remote control code first (see page 54).

• When learning commands, make sure that the transmitting ends of both remote controllers are pointing at each other.

• Are you trying to learn from a remote controller that cannot be used for learning? Some commands cannot be learned, especially those that contain several instructions.

Recording

Can’t record

• On your recorder, make sure the correct input is selected.

• To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e.g., TAPE IN to TAPE OUT, or

VIDEO 1 IN to VIDEO 1 OUT).

Others

The sound changes when I connect my headphones

• When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo,

Mono, or Direct, in which case, it stays the same.

How do I change the language of a multiplex source

• Use the Multiplex setting in “4. Audio Adjust” to select Main or Sub (page 49).

The functions don’t work

• To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 29).

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least 5 seconds, and then plug it back in again.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. “Clear” will appear on the display and the AV receiver will enter

Standby mode.

Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby.

61

62

Specification

Amplifier Section

Power Output

2 channels driven:

Dynamic Power

75 W + 75 W (8

Ω, 20 Hz–20 kHz, FTC)

100 W + 100 W (6

Ω, 1 kHz, FTC)

180 W + 180 W (3

Ω, Front)

140 W + 140 W (4 Ω, Front)

95 W + 95 W (8

Ω, Front)

THD (Total Harmonic

Distortion)

Damping Factor

0.08% (Power Rated)

60 (Front, 1 kHz, 8

Ω)

Input Sensitivity and

Impedance 200 mV/ 47 k Ω (LINE)

Output Level and

Impedance 200 mV/ 470

Ω (REC OUT)

Frequency Response 10 Hz–100 kHz/ +1 dB, –3 dB (Direct mode)

Tone Control ±10 dB, 50 Hz (BASS)

±10 dB, 20 kHz (TREBLE)

Signal to Noise Ratio 100 dB (LINE, IHF-A)

Speaker Impedance 6

Ω–

Video Section

Input Sensitivity/Output

Level and Impedance 1 Vp-p /75

Ω (Component and S-Video Y)

0.7 Vp-p /75

Ω (Component Pb/Cb, Pr/Cr)

0.28 Vp-p /75

Ω (S-Video C)

1 Vp-p /75

Ω (Composite)

Component Video

Frequency Response 5 Hz – 50 MHz

Tuner Section

■ FM

Tuning Frequency

Range

Usable Sensitivity

87.5 MHz– 107.9 MHz

Stereo: 22.2 dBf (75

Ω IHF)

Mono: 15.2 dBf (75

Ω IHF)

Signal to Noise Ratio Stereo: 67 dB (IHF-A)

Mono: 73 dB (IHF-A)

THD Stereo: 0.5% (1 kHz)

Mono: 0.3% (1kHz)

Frequency Response 30 Hz–15 kHz / ±1 dB

Stereo Separation 40 dB (1 kHz)

■ AM

Tuning Frequency

Range

Usable Sensitivity

530 kHz–1710 kHz

300 µV/m

Signal to Noise Ratio 40 dB

THD 0.70%

General

Power Supply

Power Consumption

Standby Power

Consumption

Dimensions

(W

×

H

×

D)

Weight

AC 120 V, 60 Hz

6.2 A

0.1 W

17-1/8"

435

×

5-7/8"

×

14-3/4"

×

150

×

374 mm

20.9 lbs.

9.5 kg

■ Video Inputs

Component

S-Video

Composite

DVD, VIDEO1, VIDEO2

DVD, VIDEO1, VIDEO2

DVD, VIDEO1, VIDEO2, VIDEO3

■ Video Outputs

Component

S-Video

Composite

MONITOR

MONITOR OUT, VIDEO1

MONITOR OUT, VIDEO1

■ Audio Inputs

Digital Inputs

Analog Inputs

Multichannel Input

Optical: 3

Coaxial: 1

DVD (MULTICHANNEL), VIDEO1,

VIDEO2, VIDEO3, TAPE, CD

6 jacks

■ Audio Outputs

Analog Outputs TAPE, VIDEO1

Subwoofer Pre Outputs 1

Speaker Outputs

Phones

SP A (L, R, C, SL, SR, SBL, SBR)

SP B (L, R)

1

Specifications and features are subject to change without notice.

Memo

63

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8124

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/

ONKYO EUROPE UK Office

Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ

UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452

ONKYO CHINA LIMITED

Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.ch.onkyo.com/

HOMEPAGE http://www.onkyo.com/

I0508-1

SN 29344094

(C) Copyright 2005 ONKYO CORPORATION Japan. All rights reserved.

64

* 2 9 3 4 4 0 9 4 *

No results