advertisement
VZ Series
LCD Monitor
User Manual
Copyright
Copyright © 2014 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ
Corporation to notify any person of such revision or changes.
The performance of flicker-free may be affected by external factors such as poor cable quality, unstable power supply, signal interference, or poor grounding, and not limited to the above mentioned external factors. (Applicable for flicker-free models only.)
Servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as dropping or mishandling occurs, contact qualified service personnel for servicing.
Safety
Please follow these safety instructions for best performance, and long life for your monitor.
• The AC plug isolates this equipment from the AC supply.
• The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible.
• This product should be operated from the type of power indicated on the marked label. If you are not sure of the type of power available, consult your dealer or local power company.
• An approved power cord greater or equal to H03VV-F or H05VV-F, 2G or 3G, 0.75mm
2
must be used.
Care And Cleaning
• Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass cleaners.
• Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a built-in installation unless proper ventilation is provided.
• Never push objects or spill liquid of any kind into this product.
2
BenQ ecoFACTS
BenQ has been dedicated to the design and development of greener product as part of its aspiration to realize the ideal of the “Bringing Enjoyment ‘N Quality to Life” corporate vision with the ultimate goal to achieve a low-carbon society. Besides meeting international regulatory requirement and standards pertaining to environmental management, BenQ has spared no efforts in pushing our initiatives further to incorporate life cycle design in the aspects of material selection, manufacturing, packaging, transportation, using and disposal of the products. BenQ ecoFACTS label lists key ecofriendly design highlights of each product, hoping to ensure that consumers make informed green choices at purchase. Check out BenQ’s CSR Website at http://csr.BenQ.com/ for more details on
BenQ’s environmental commitments and achievements.
3
Table of Contents
Getting the most from your BenQ monitor ................................................14
4
Box contents
When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement.
LCD Monitor
CD-ROM
Monitor Base
Power Cable D-Sub Cable DVI Cable HDMI Cable
• *: Optional accessory.
• Available accessories and the pictures shown here may differ from the actual contents and the product supplied for your region. For cables that are not supplied with your product, you can purchase them separately.
• Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The fitted foam packing is ideal for protecting the monitor during transport.
Always keep the product and accessories out of reach of small children.
5
Installation
• If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on the purchased model.
• Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
Attach the monitor stand
1. Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding.
2. Gently lay the screen face down on a flat clean padded surface.
3. Orient and align the stand base socket with the end of the stand arm, then push them together until they click and lock into place.
4. Tighten the screw on the bottom of the monitor base as illustrated.
5. Carefully lift the monitor, turn it over and place it upright on its stand on a flat even surface.
You should position the monitor and angle the screen to minimize unwanted reflections from other light sources.
6
Cleaning
Please disconnect the power cord before cleaning the product.
Clean the cabinet regularly with a cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Adjusting viewing angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
7
Connecting the monitor
VZ2250/VZ2350 VZ2350HM
1
VZ2250H
3 4
1
2 3 4 5
1 2 4 6
No.
Description
1 AC power input jack
2 HDMI socket
3 DVI-D socket
4 D-Sub socket
5 Audio Line In
6 Audio Line Out
1. To protect equipment, always turn off the PC and LCD monitor before connecting.
2. Connect the plug of the D-Sub cable (at the end without the ferrite filter) to the monitor video socket. Connect the other end of the cable (at the end with the ferrite filter) to the computer video socket.
3. (Optional – Requires a video card with DVI port) - Connect one end of the DVI cable to the back of the monitor and connect the other end to the computer’s DVI port.
4. Turn on your monitor and computer. If your monitor displays an image, installation is complete.
If it does not display an image, please refer to
.
8
Removing the monitor stand
1. Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable.
2. Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding, before laying the screen face down on a flat clean padded surface.
3. Release the screw on the bottom of the monitor base and detach the monitor base as illustrated.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
9
The control panel
1 2 3
4
5
No.
VZ2250 / VZ2350
Description No.
VZ2250H / VZ2350HM
Description
3
4
1
2
5
Source / Auto / Exit
ECO / -
4:3 or wide / +
Menu / Enter
Power
3
4
1
2
5
Source / Auto / Exit
ECO / -
Volume / +
Menu / Enter
Power
Source / Auto / Exit
• Press and hold the AUTO key for 3 serconds to adjusts vertical position, phase, horizontal position and pixel clock automatically.
• Press the
AUTO key to switch to a desired input source, and confirm with the MENU key.
• When in the OSD menu, press to exit.
ECO / -
• By default, the key is the hot key for ECO.
• When in the OSD menu, press for Down/Decrease adjustment.
Volume / +
• By default, the key is the hot key for
Volume.
• When the input source is HDMI, press to select the audio source, and confirm with the MENU key.
• When in the OSD menu, press for Up/Increase adjustment.
4:3 or wide / +
• By default, the key is the hot key for 4:3 or wide image aspect ratio. (Not available if the screen size is 4:3 or the input signal resolution is wide already.)
• When in the OSD menu, press for Up/Increase adjustment.
Menu / Enter
• Press to display the OSD menu.
• When in the OSD menu, press to confirm the selection.
Power
Press the button to turn on / off the monitor.
10
Basic OSD menu operation
• Press the MENU button to activate the OSD menu.
• Press - or + to navigate through the menu options. Once the desired option is highlighted, press the MENU key to confirm the selection.
Press - or + to change the settings of the selected function.
Press MENU key to save the new setting and exit the current function. Press - or + to select another function in sub-menu.
Press AUTO to exit. If you want to adjust any other function, repeat the previous steps.
• OSD Lock: To lock the OSD, press and hold the MENU key while the monitor is off and then press the key to turn the monitor on. To unlock the OSD, press and hold the
MENU button while the monitor is off and then press the key to turn the monitor on.
• If the product screen size is 4:3 or input signal resolution is wide, the Image Ratio is disabled.
• When DCR is on and there is no OSD menu, press the - key is available to adjust ECO and will set DCR to off.
Power LED indicator
LED indicator
Blue
Orange
System status
The monitor is powered on.
The monitor is in Standby mode.
11
Menu introduction
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out. And keys that are not available will be disabled and the corresponding OSD icons will disappear.For models without certain functions, their settings and related items will not appear on the menu.
Main menu Function Range
Luminance Contrast
Adjusts the degree of difference between darkness and lightness.
0-100
Brightness
Adjusts the balance between light and dark shades. 0-100
Eco mode
Select a picture mode that best suits the type of images shown on the screen.
•
Standard
•
Text
•
Internet
Image
Setup
•
Game
•
Movie
DCR Sets dynamic contrast ratio.
•
Sports
•
On
AMA
(for models with HDMI inputs)
Clock
Improves the gray level response time of the LCD panel.
Adjusts the pixel clock frequency timing to synchronize with the analog input video signal.
Phase
Adjusts the pixel clock phase timing to synchronize with the analog input video signal.
H. Position
Adjusts the horizontal position of the screen image.
•
Off
•
•
•
Premium
High
Off
0-100
0-100
0-100
V. Position
Adjusts the vertical position of the screen image.
0-100
Image Ratio This feature is provided to allow aspect ratios
•
Wide
other than 16:9 to be displayed without geometric distortion.
•
4:3
12
Main menu Function Range
Color
Temp.
Warm
Normal
Cool
User
Applies a warm tint to the image and is factory pre-set to the news print standard white color.
Allows video and still photographs to be viewed with natural coloring.
Applies a cool tint to the image and is factory pre-set to the PC industry standard white color.
The blend of the Red, Green and Blue primary colors can be altered to change the color tint of the image. Go to the succeeding R (red), G
(green), and B (blue) menus to change the settings.
•
•
Red
Green
•
Blue sRGB
Decreasing one or more of the colors will reduce their respective influence on the color tint of the image. (e.g. if you reduce the Blue level the image will gradually take on a yellowish tint. If you reduce Green, the image will become a magenta tint.)
Recall sRGB Color Temperature from EEPROM.
OSD Setup H. Position
Adjusts the horizontal position of the OSD menu. 0-100
0-100
V. Position
Adjusts the vertical position of the OSD menu.
Timeout
Adjusts the display time of the OSD menu.
Language
Sets the OSD menu language.
5-100
•
English
•
Español
•
Français
•
Português
• Русский
• 简体中文
Extra
• 繁體中文
Input Select Use this to change the input to that appropriate to your video cable connection type.
• 한국어
•
D-Sub
•
DVI
• HDMI
(selected models only)
DDC/CI
Allows the monitor settings to be set through the software on the PC.
•
On
•
Off
Reset
Resets all mode, color and geometry settings to the factory default values.
Information Displays the current monitor property settings.
•
Resolution
•
H.
Frequency
•
V.
Frequency
13
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ LCD monitor, you should install the custom BenQ
LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software.
These circumstances relate to which version of Microsoft Windows you are using, and whether you are connecting the monitor and installing the software onto a new computer (without existing monitor driver software), or whether you are upgrading an existing installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the monitor to your computer), Windows will automatically recognize the new (or different) hardware, and will launch its Found New Hardware wizard.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click the
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor model. Further details and step-by-step instructions for either an automatic (new) or upgrade
(existing) installation, see:
•
"How to install the monitor on a new computer" on 15
.
•
"How to upgrade the monitor on an existing computer" on 16 .
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an
Administrator or as a member of the Administrators group in order to install the monitor driver software.
Furthermore, if your computer is connected to a network which has security access requirements, network policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor
.
14
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before. This instruction is only suitable for a computer which has never been used before, and for which the BenQ LCD
Monitor is the first ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions. You
1. Follow the instructions in
.
When Windows starts, it will automatically detect the new monitor and launch the
Found New
Hardware Wizard. Follow the prompts until it displays the option to Install Hardware
Device Drivers.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check Search for a suitable driver for my device option, and click Next.
4. Check the option for CD-ROM drives (uncheck all others) and click Next.
5. Look to confirm that the wizard has selected the correct name of your monitor and click Next.
6. Click Finish.
7. Restart the computer.
To find the suitable driver files for the purchased model, refer to the following table.
VZ2250
VZ2350
Driver files Suitable models
VZ2250 / VZ2250H
VZ2350 / VZ2350HM
15
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer. It is currently tested as compatible for Windows 8.1, Windows
8, and Windows 7 Operating System (OS).
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information file (.inf) on the
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting
Windows install the corresponding driver files from the CD. You need only steer it in the right direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you through the file selection and installation process.
See:
•
"How to install on Windows 8 (8.1) system" on 17.
•
"How to install on Windows 7 system" on 18.
16
How to install on Windows 8 (8.1) system
1. Open Display Properties.
Move the cursor to the lower-right of the screen or press the Windows + C buttons on the keyboard to bring up the Charm bar. Go to Settings, Control Panel, Devices and Printers and right-click the name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, and right-click the name of your monitor from the menu.
2. Select Properties from the menu.
3. Click the
Hardware tab.
4. Click Generic PnP Monitor, and then the Properties button.
5. Click the
Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the
Update Driver Software window, select the option Browse my computer for
driver software.
8. Click
Browse and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click
Next.
This will copy and install the appropriate monitor driver files to your computer.
10. Click
Close.
You may be prompted to restart your computer after the driver update is complete.
17
How to install on Windows 7 system
1. Open Display Properties.
Go to Start, Control Panel, Hardware and Sound, Devices and Printers and right-click the name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, and right-click the name of your monitor from the menu.
2. Select
Properties from the menu.
3. Click the Hardware tab.
4. Click
Generic PnP Monitor, and then the Properties button.
5. Click the Driver tab and the Update Driver button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the Update Driver Software window, select the option Browse my computer for
driver software.
8. Click Browse and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click Next. This will copy and install the appropriate monitor driver files to your computer.
10. Click Close.
You may be prompted to restart your computer after the driver update is complete.
18
Troubleshooting
The power LED indicator is not on.
• Make the power cord is properly connected to a grounded power outlet and the monitor.
• Make sure you have pressed the key.
The image is blurred.
• Read the instructions in "Preset display modes" on 25 , and then select the correct
resolution, refresh rate and make adjustments based on these instructions.
• Remove the extension cable for the test. It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the instructions in "Preset display modes" on 25 . Select the native resolution.
Pixel errors can be seen.
One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color.
• Clean the LCD screen.
• Cycle power on-off.
• These are pixels that are permanently on or off and is a natural defect that occurs in LCD technology.
The image has a faulty coloration. It has a yellow, blue or pink appearance.
If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
No image can be seen.
If the LED is illuminated in blue and there is a message Out of Range on the screen, this means you are using a display mode that this monitor does not support, please change the
setting to one of the supported mode. Please read "Preset display modes" on 25.
Faint shadow from the static image displayed is visible on the screen.
• Activate the power management function to let your computer and monitor go into a low power "sleep" mode when not actively in use.
• Use a screensaver to prevent the occurrence of image retention.
Is the prompt on the display illuminated in orange?
If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
19
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
The image is distorted, flashes or flickers.
Read the instructions in "Preset display modes" on 25 , and then select the correct
resolution, refresh rate and make adjustments based on these instructions.
You are running the monitor at its native resolution, but the image is still distorted.
Images from different input sources may appear distorted or stretched on the monitor running at its native resolution. To have the optimal display performance of each type of input sources, you can use the
Image Ratio function to set a proper aspect ratio for the
input sources. See "Image Ratio" on 12 for details.
The image is displaced in one direction.
Read the instructions in "Preset display modes" on 25 , and then select the correct
resolution, refresh rate and make adjustments based on these instructions.
No sound can be heard from the built-in speakers (for models with speakers only):
• Check whether Line In is properly connected.
• Increase the volume (volume may be muted or too low).
Need more help?
If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: [email protected].
20
Specification
VZ2250
Panel
Resolution
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
Horizontal scan
Size(Maximum)
Vertical scan range
Vertical scan Size
(Maximum)
Optimal preset resolution
Plug & Play
Input Connector
Input Video Signal
Speaker
Power Source
Power Consumption
Physical
Characteristics
Environmental
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height (with base)
Width
Depth
Weight (monitor only)
Wall Mount
Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
VZ2250
TFT Color LCD
54.62cm diagonal
0.08265*RGB (H) mm x 0.24795 (V) mm
R, G, B Analog lnterface
H/V TTL
16.7M Colors
165MHz
30 ~ 83kHz
476.064mm
50 ~ 76Hz
267.786mm
1920x1080@60Hz
VESA DDC2B
VGA / DVI
Analog: 0.7Vp-p (standard), 75 OHM,
Positive
NA
100-240V, 50/60Hz
24W (typical)
Standby < 0.5 W
0-24 hrs
VGA/DVI
Detachable
372.2 (mm)
499.5 (mm)
181.1 (mm)
3.58 kg
100 x 100 mm
0°C to 40°C
-20°C - +60°C
15% to 90% (non-condensing)
15% to 90% (non-condensing)
0~ 5000m (0~ 16404 ft)
0~ 12192m (0~ 40000 ft)
21
VZ2250H
Panel
Resolution
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
Horizontal scan
Size(Maximum)
Vertical scan range
Vertical scan Size
(Maximum)
Optimal preset resolution
Plug & Play
Input Connector
Input Video Signal
Speaker
Power Source
Power Consumption
Physical
Characteristics
Environmental
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height (with base)
Width
Depth
Weight (monitor only)
Wall Mount
Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
VZ2250H
TFT Color LCD
54.61cm diagonal
0.08265*RGB (H) mm x 0.24795 (V) mm
R, G, B Analog lnterface
H/V TTL
16.7M Colors
165MHz
30 ~ 83kHz
476.064mm
50 ~ 76Hz
267.786mm
1920x1080@60Hz
VESA DDC2B
VGA / HDMI
Analog: 0.7Vp-p (standard), 75 OHM,
Positive
NA
100-240V, 50/60Hz
24W (typical)
Standby < 0.5 W
0-24 hrs
VGA/HDMI
Detachable
372.2 (mm)
499.5 (mm)
181.1 (mm)
3.58 kg
100 x 100 mm
0°C to 40°C
-20°C - +60°C
15% to 90% (non-condensing)
15% to 90% (non-condensing)
0~ 5000m (0~ 16404 ft)
0~ 12192m (0~ 40000 ft)
22
VZ2350
Panel
Resolution
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
Horizontal scan Size
(Maximum)
Vertical scan range
Vertical scan Size
(Maximum)
Optimal preset resolution
Plug & Play
Input Connector
Input Video Signal
Speaker
Power Source
Power Consumption
Physical
Characteristics
Environmental
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height (with base)
Width
Depth
Weight (monitor only)
Wall Mount
Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
VZ2350
TFT Color LCD
58.42cm diagonal
0.0884*RGB (H) mm x 0.2652 (V) mm
R, G, B Analog lnterface
H/V TTL
16.7M Colors
165MHz
30 ~ 83kHz
509.184mm
50 ~ 76Hz
286.416mm
1920x1080@60Hz
VESA DDC2B
VGA/DVI
Analog: 0.7Vp-p (standard), 75 OHM,
Positive
NA
100-240V, 50/60Hz
26W (typical)
Standby < 0.5 W
0-24 hrs
VGA/DVI
Detachable
389.2 (mm)
532.6 (mm)
181.1 (mm)
4.02 kg
100 x 100 mm
0°C to 40°C
-20°C - +60°C
15% to 90% (non-condensing)
15% to 90% (non-condensing)
0~ 5000m (0~ 16404 ft)
0~ 12192m (0~ 40000 ft)
23
VZ2350HM
Panel
Resolution
Model name
Driving system
Viewable Image Size
Pixel pitch
Video
Separate Sync.
Display Color
Dot Clock
Horizontal scan range
Horizontal scan Size
(Maximum)
Vertical scan range
Vertical scan Size
(Maximum)
Optimal preset resolution
Plug & Play
Input Connector
Input Video Signal
Speaker
Power Source
Power Consumption
Physical
Characteristics
Environmental
Off timer
Connector Type
Signal Cable Type
Dimensions & Weight:
Height (with base)
Width
Depth
Weight (monitor only)
Wall Mount
Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
VZ2350HM
TFT Color LCD
58.42cm diagonal
0.0884*RGB (H) mm x 0.2652 (V) mm
R, G, B Analog lnterface
H/V TTL
16.7M Colors
165MHz
30 ~ 83kHz
509.184mm
50 ~ 76Hz
286.416mm
1920x1080@60Hz
VESA DDC2B
VGA / DVI / HDMI / Line in
Analog: 0.7Vp-p (standard), 75 OHM,
Positive
2W x 2
100-240V, 50/60Hz
30W (typical)
Standby < 0.5 W
0-24 hrs
VGA/HDMI
Detachable
389.2 (mm)
532.6 (mm)
181.1 (mm)
4.03 kg
100 x 100 mm
0°C to 40°C
-20°C - +60°C
15% to 90% (non-condensing)
15% to 90% (non-condensing)
0~ 5000m (0~ 16404 ft)
0~ 12192m (0~ 40000 ft)
24
Preset display modes
Mode Resolution
VGA
SVGA
XGA
SXGA
WXGA+
WSXGA
HD
640×480@60Hz
640×480@72Hz
640×480@75Hz
800×600@56Hz
800×600@60Hz
800×600@72Hz
800×600@75Hz
1024×768@60Hz
1024×768@70Hz
1024×768@75Hz
1280×1024@60Hz
1280×1024@75Hz
1440×900@60Hz
1440×900@60Hz
1680×1050@60Hz
1680×1050@60Hz
1920×1080@60Hz
640×350@70Hz
IBM-MODE DOS
720×400@70Hz
MAC MODE VGA 640×480@67Hz
MAC MODE SVGA 832×624@75Hz
MAC MODE XGA 1024×768@75Hz
H.Frequency
56.476
60.023
63.981
79.976
55.935
55.469
65.290
64.674
31.469
37.861
37.500
35.156
37.879
48.077
46.875
48.363
67.500
31.469
31.469
35.000
49.725
60.241
V.Frequency
70.069
75.029
60.020
75.025
59.887
59.901
59.954
59.883
59.940
72.809
75.00
56.250
60.317
72.188
75.000
60.004
60.000
70.087
70.087
66.667
74.551
74.927
Plug & Play DDC2B feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
25
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project