Docking Cradle for WACS7000 DC1000

Quick Start Guide

A

B

C

Install

Connect

Enjoy

Eng

What’s in the box

Docking cradle 8 x iPod dock adaptor

4 x GoGear dock adaptors

DIN Cable RCA Cable Quick Start Guide

IMPORTANT!

• DC1000 is an iPod reader which transmits the signal from iPod to external speaker. It can be powered by power supply unit

SA1460-240200 or SUPPLY APPARATUS FOR GENERAL USE, alternatively a special system having suitable supplying parameters through 9 pin DIN cable is available.

• For indoor use only.

What else you’ll need

or

WACS7000 iPod GoGear

IMPORTANT!

The docking cradle only supports the devices listed below. Do not try it on any other device!

– Apple iPod (iPod video, iPod nano, iPod Photo and iPod mini)

– Philips GoGear HDD players (Charge function optional)

A

1

Install

1

Change the docking cradle to match with your portable player

The docking cradle can support both iPod and GoGear. Follow steps below to change it into desired mode

– Default position is prepared for iPod

– Go to A

2

Install for iPod user.

1. Slide the front cover horizontally in the direction shown above to open the front cover

2. Rotate the front cover in 180 degree

3. Slide the front cover back onto the docking cradle

A

2

Install

2

Install dock adaptor

Insert a dock adapter that matches with your portable player (take iPod adapter as example).

2

1

3

Install portable player

Plug your portable player into the cradle (take iPod as example).

– Turn on the power of pipe speakers.

Un-install

To connect with a different portable player, dismount the iPod first, then pop up the dock adapter and then replace it with a new dock adapter of the matching type.

B

Connect

Connect AC power

The DC1000 is powered through WACS7000 by connect it with WACS7000

Center or Station via the 9 pin DIN cable.

Center

Station

Connect audio cable

Plug one end of the audio cable to the black 3.5mm Audio Out jack, and the other end to the audio in jacks on the WACS7000 Center or Station (note that the red terminal should be connected to the red jack).

(Audio Out)

Center

(Audio Out)

Station

Note: Adjust volume in case playing sound is low after connect your iPod or GoGear with WACS7000!

C

1

Enjoy

When connection is successfully made, power on the WACS7000

Center or Station, then press SOURCE button to switch it to AUX mode, playing will start immediately.You can press the controls on your iPod or GoGear to skip/search for desired track or to stop playing.

Besides, you can also use the 2-way remote control that comes with

WACS7000 to enjoy your iPod or GoGear with WACS7000.

Activating the 2-way remote control

Press PORTABLE button

Using the 2-way remote control with the docking

Note: Only the Volume button, Skip/search button and

2; button will be effective

Play

Press

2; to start playing

• While playing, press

2; to stop playing temporarily. Press

2; again to resume playing.

Adjust volume

Press Volume +/– to increase or reduce volume

Skip to the previous or next track

• Press

∞ to skip to the previous track

• Press

§ to skip to the next track

De-activating the 2-way remote control

Press SOURCE, HDD or CD button on the 2-way remote control, the remote control will resume its function with WACS7000 and will no longer be able to control the docking.

PORTABLE

PORTABLE

SAME ARTIST

DBB

SMART EQ

SEARCH

SOURCE

SOURCE

C

2

Enjoy

Charging iPod using the docking station

When the iPod is properly connected on the docking cradle and the WACS7000 is powered on, battery charging start automatically.

Helpful hint:

• You can also use a USB cable (not supplied) to connect the docking cradle with your PC to charge your iPod or GoGear

Troubleshootting

Problem

No sound

Solution

• Check if the audio cable is well connected.

• Check if the power cable that connects the DC1000 with

WACS7000 is well connected.

No any response after pressed the buttons on the

2-way remote control

Sound can't be adjusted

• Check if the 2-way remote control is at "Portable" mode.

Press the Portable button to switch it to Portable mode.

• Point the remote control to the docking station.

• Once entering Portable mode, the 2-way remote control works with the DC1000. Do not point the remote control to

WACS7000 or your iPod or GoGear.

• Check if the batteries of the remote control is used up. If yes, replace it with new batteries.

• Only the Volume button, Skip/search button and Play/pause button is applicable. (see Enjoy section for details.)

• Check if the audio cable is properly connected: the audio cable should be connected to the black 3.5mm jack in the middle of the backside of the docking station.

Specifications

Dock Connectivity – Audio Out : 3.5 mm (Cable provided)

– AV Out: 3.5 mm for Audio/Video Out (Cable optional )

– DC in for GoGear and iPod : 9 pins DIN cable(Cable provided)

– USB: Mini USB (Cable optional )

– Remote Control: IR build-in

0820 901115

070 253 010

3525 8761

09 2290 1908

08 9165 0006

0180 5 007 532

0 0800 3122 1223

01 601 1161

199 404 042

26 84 30 00

0900 0400 063

2270 8250

2 1359 1440

902 888 785

08 632 0016

02 2310 2116

0906 1010 017

Need help?

www.philips.com/support or call our helpdesk

Specifications are subject to change without notice.

© Royal Philips Electronics N.V. 2006

All rights reserved. www.philips.com