advertisement
APPENDIX H
: USER’S MANUAL
Test Report Number: GETEC-E3-08-036
FCC Class B Certification
EUT Type: LCD Monitor
FCC ID: BEJM4714CG
User’s Guide
M4714C
M
ake sure to read the Safety Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
S
ee the label attached on the product and give the information to your dealer when you ask for service.
Connecting the stand
- Only on some models.
1.
Take the parts for the stand out of the box and assemble them as shown in the picture.
Parts
First, check if the following parts are all present.
Screws (4)
Stand (1) cable management (1)
2.
Place a soft cloth on the table and put the product with the screen facing downward.
Connect the stand as shown in the following picture.
3.
Use the screws to secure the stand on the rear side of the product as shown in the diagram.
1
Connecting the Speakers
- Only on some models.
Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable.
After installing your speakers, use holders and cable ties to organize the speaker cables.
Cable holder
Remove the paper.
* This feature is not available in all model.
Cable tie
* This feature is not available in all model.
When the speaker is installed.
*Connect the input terminal with a proper color match.
2
- Only on some models.
To install Portrait
"When installing Portrait, rotate it clockwise based on its front."
3
Using the Remote Control
Name of the Remote Control Buttons
• AV Button
• Sleep Button
When watching AV, RGB PC,HDMI/DVI
,Component1, Component2
The product will be automatically turned off after a certain period of time.
Press this button repetitively to select an appropriate time duration
• PSM Button
- Toggles through preset video settings.
There is not a function which is supported
• Menu Button
• UP and Down buttons
Bring up and down direction adjustment.
• Mute button
1
4
7 8
0
2
5
3
6
9
• Power On/Off Button
• Input Select Button
(See next page)
• ARC button
Aspect Ratio Correction. Toggles through aspect ratio options.
• Auto Button
Automatic adjustment function
(Operational for the analog signal only)
There is not a function which is supported
*
There is not a function which is supported
• Exit Button
• Volume Button
Volume up and down
• Check Button
There is not a function which is supported
4
Name and Function of the Parts
* The product image in the user’s guide could be different from the actual image.
Rear View
AV IN/OUT
Power Connector : Connect the power cord
RS-232C Serial Ports
RGB PC, HDMI/DVI Ports
-HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content
Protection). Some devices require HDCP in order to display HD signals.
PC Sound Jack
: Connect the audio cable to the *LINE OUT jack of the PC sound card.
Wired Remote Control Port
AV Ports
Speaker Ports
*LINE OUT
A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of
PC sound card has only Speaker Out, reduce the PC volume.
If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using the card jumper of the program (Refer to the Sound Card Manual).
5
Connecting to External Devices
When Connecting to your PC
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable.
A
When connecting with the D-Sub signal input cable.
B
When connecting with the HDMI to DVI signal input cable (not included).
A
PC
Rear side of the product.
MAC
PC/MAC
Macintosh Adapter (not included)
Use the standard Macintosh adapter since an incompatible adapter is available in the market. (Different signaling system)
B
(not included)
Rear side of the product.
PC
* User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product.
Connect the Audio cable.
Rear side of the product.
Connect the power cord.
Rear side of the product.
PC
6
Connecting to External Devices
1
Turn on power by pressing the power button on the product.
SOURCE
AUTO/SET
ON/OFF
Power button
2
Turn on the PC.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT SET
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
A
When connecting with a D-Sub signal input cable.
• Select RGB PC : 15-pin D-Sub analog signal.
B
When connecting with a
HDMI to DVI signal input cable.
• Select HDMI/DVI :
HDMI to DVI
Digital signal.
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
Note
•
How to connect to two computers.
Connect the signal cables (
HDMI to DVI and D-Sub) to each computer.
Press the INPUT button on the remote control to select the computer to use.
•
Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.
7
Connecting to External Devices
Daisy Chain Monitors
Use this function when displaying ANALOG RGB inputs of a PC to the other product.
•
To use different products connected to each other
Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products.
PC
PC
15-pin D-Sub Signal Cable
RGB IN
RGB OUT
RGB IN
RGB OUT
RGB IN
RGB OUT
RGB IN
RGB OUT
Product 1
Product 2
Product 3 Product 4
Note
• When multi-connecting in/out cascade format, no loss cables are recommended.
We recommend that you should use cable distributor.
8
Connecting to External Devices
VESA FDMI wall Mounting
This product supports a VESA FDMI compliant mounting interface. These mounts are purchaed separately and not available from LG. Refer to the instructions included with hte mount for more info.
The Set is equipped with a kensington Securify
System connector on the back panel. The cable and lock are available separate and are not sold by LG.
For more info, visit http://www.kensington.com, the internet home page of the Kensington company.
9
Using the Remote Control
• AV Button
Toggles through video
AV Component1
Component2 RGB PC
HDMI/DVI
1
4
7 8
0
2
5
3
6
9
• Input Select Button
If you press the button once, the following Input Signal
Window will appear. Select the signal type you want using the button.
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
*
Inserting batteries into remote control.
1. Slide off the battery cover.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cover.
• Dispose of used batteries in the recycle bin to prevent environmental pollution.
AAA Type
10
Connecting to External Devices
Video Input
Connect the video cable as shown in the below figure and then connect the power cord (See page 5).
A When connecting with a BNC cable.
•
Connect the input terminal with a proper color match.
B
When connecting with a S-Video cable.
•
Connect to the S-Video input terminal to watch high image quality movies.
VIDEO
Product
AV IN
L-AUDIO-R
VIDEO
Product
AV IN
L-AUDIO-R
S-VIDEO S-VIDEO
AV
OUT
AV
OUT
Audio Cable
(not included)
Audio Cable
(not included)
BNC Cable
(not included)
S-Video Cable
(not included)
VCR/DVD Receiver VCR/DVD Receiver
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT SET
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
A
B
When connecting with an BNC cable.
• Select AV.
When connecting with an S-Video cable.
• Select AV.
Note
• When the BNC cable is connected simultaneously with S-Video cable, S-Video input has a priority.
11
Connecting to External Devices
Component Input (480p/576p/720p/1080p/1080i/480i/576i)
Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 5).
•
Connect the input terminal with a proper color match.
A
B
Y
Product
COMPONENT IN
VIDEO
P
B
P
R
1
L-AUDIO-R
2
Y
Product
COMPONENT IN
VIDEO
P
B
P
R
1
L-AUDIO-R
2
BNC Cable
(not included)
Audio Cable
(not included)
BNC Cable
(not included)
Audio Cable
(not included)
HDTV Receiver
HDTV Receiver
Note
- Some devices may require HDCP in order to display HD signals.
- Component doesn't support HDCP.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT SET
Or, press the SOURCE button on the back of the product.
SOURCE
A
B
• Select Component 1
• Select Component 2
AUTO/SET
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
12
Connecting to External Devices
HDMI Input (480p/576p/720p/1080i/1080p)
-HDMI Supports High Definition input and HDCP (High-bandwidth Digital Content
Protection). Some devices require HDCP in order to display HD signals.
Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 5).
HDMI/DVI IN
Product
RGB IN AUDIO
(RGB/DVI)
Product
HDMI/DVI IN RGB IN
AUDIO
(RGB/DVI)
RGB OUT
RGB OUT
HDMI to DVI
Signal Cable
(not included)
RCA-PC
Audio Cable
HDMI Signal Cable
(not included)
VCR/DVD/Set-top Box
Note : Dolby Digital is not supported.
VCR/DVD/Set-top Box
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT SET
Or, press the SOURCE button on the back of the product.
SOURCE
AUTO/SET
When connecting with a
HDMI to DVI signal input cable.
When connecting with a
HDMI signal input cable.
• Select HDMI/DVI
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
13
Connecting to External Devices
Watching AV Outputs
- When using AV input, you can connect the AV Out to other monitors.
Video/TV
BNC Cable
(not included)
Audio Cable
(not included)
VIDEO
AV IN
L-AUDIO-R
AV
OUT
S-VIDEO
Product
BNC Cable
(not included)
Audio Cable
(not included)
Video/TV
Note
• When multi-connecting in/out cascade format, no loss cables are recommended.
We recommend that you should use cable distributor.
14
Cable management
- Only on some models.
1.
Arrange the cables in the center as shown in the following picture.
2.
Fit the cable guide to the back to help manage the cables.
cable management
Removing the cable guide.
Hold the Cable management with both hands and pull it downward.
Warning
• Do not use the cable management as a handle for the Monitor.
15
User Menus
Screen Adjustment options
SOURCE
AUTO/SET ON/OFF
SOURCE
AUTO/SET
ON/OFF
Power Button
• Press this button to turn on the power. Press this button again to turn it off.
Power Indicator
• This Indicator lights up blue when the display operates normally(on mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber.
MENU Button
• Use this button to show/hide the OSD (On Screen Display) menu screen.
• Use this button to select an icon or adjust the setting in the OSD screen.
OSD Select /
Adjust Button
• Adjust the up and down.
• Adjust the volume.
Volume 35
16
User Menus
Screen Adjustment options
AUTO/SET Button
[For PC Analog signal]
[When 1920 X1080 is selected]
SOURCE Button
SOURCE
- Toggles between inputs
AUTO/SET
AV
Composite Video, Separate Video
Component 1
HDTV, DVD
Component 2
HDTV, DVD
RGB PC
15-pin D-Sub analog signal
HDMI/DVI Digital signal
Input
AV
Component1
Component2
RGB PC
HDMI/DVI
IR Receiver
• This is where the unit receives signals from the remote control.
17
User Menus
OSD Menu
Icon Function Description
Adjusts screen brightness, contrast and color that you prefer.
Picture
Adjusts the audio options.
Audio
Adjusts the timer options.
Time
Adjusts the screen status according to the circumstances.
Option
Adjust Set ID and check Serial No. and SW version.
Information
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation.
18
User Menus
How to adjust the OSD (On Screen Display) screen
Pops up the menu screen
Move where you want to adjust
Select a menu icon
Move where you want to adjust
Select a menu icon
Adjust the status
Save adjustment
Exit from the menu screen.
• Use the remote control to adjust the OSD screen.
1
Press the MENU Button, then the main menu of the OSD appears.
2
To access a control, use the Buttons.
3
When the icon you want becomes highlighted, press the SET Button.
4
Use the Buttons to adjust the item to the desired level.
5
Accept the changes by pressing the SET Button.
6
Exit the OSD by pressing the EXIT Button.
How to adjust the screen automatically
Press the AUTO/SET button (AUTO button on a remote Control) in the
PC analog signal. Then optimal screen settings will be selected that fit into the current mode. If adjustment is not satisfactory, you can adjust the screen manually.
[When 1920 X1080 is selected]
19
User Menus
Adjusting Screen Color
Picture
Mode
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
Vivid
Standard
Cinema
Sport
Game
User1
User2
MENU
Toggles between screen presets.
• Vivid : Select this option to display with a sharp image.
• Standard : The most general and natural screen display status.
• Cinema : Select this option to lower brightness by one level.
• Sport : Select this option to display with a soft image.
• Game : To enjoy dynamic image when playing a game.
• User1,2 : Select this option to use the user-defined settings.
User2
Backlight
Contrast
Brightness
Color
Sharpness
Tint
Expert
MENU
20
90
50
50
50
50
Backlight : To control the brightness of the screen,adjust the brightness of LCD panel.
Contrast : Adjust the difference between the light and dark levels in the picture.
Brightness : To adjust the brightness of the screen.
Color : To adjust the color to desired level.
Sharpness : To adjust the clearness of the screen.
Tint :To adjust the tint to desired level.
Expert : To compensate for each image mode, or adjust image values according to a particular image. (Applied only to User2 menu.)
Note
If the 'Picture Mode' setting in the Picturemenu is set to Vivid, Standard, Cinema,
Sport or Game the subsequent menus will be automatically set.
20
User Menus
Adjusting Screen Color
Color
Temperature
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
Cool
Medium
Warm
User
MENU
Color Settings
• Cool : Slightly purplish white.
• Medium : Slightly bluish white.
• Warm : Slightly reddish white.
• User : Select this option to use the user-defined settings.
User
Red
Green
Blue
0
0
0
MENU
Red / Green / Blue
Set your own color levels.
21
User Menus
Adjusting Screen Color
Advanced
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
To set
MENU
• Gamma : Set your own gamma value. : -50/0/50
On the monitor, high gamma values display whitish images and low gamma values display high contrast images.
• Film Mode : (Function works in the following mode - AV, Component 480i/576i)
When you watch a movie, this function adjusts the set to the best picture appearance.
• Black Level : (Function works in the following mode - AV(NTSC), HDMI/DVI adjusts the contrast and the brightness of the screen using the black level of the screen.
• Low : The reflection of the screen gets brighter.
• High : The reflection of the screen gets darker.
• NR : Removing the noise up to the point where it does not damage the original picture.
22
User Menus
Adjusting Screen Color
Aspect Ratio
To select the image size of the screen.
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
16:9
Original
4:3
14:9
Zoom1
Zoom2
MENU
<AV>
16:9
Just Scan
Original
4:3
1:1
14:9
Zoom1, 2
Widescreen mode.
Allows you to enjoy the transmitted data fully without any images cut off.
(* This menu is activated only in 720p, 1080p and 1080i in Component mode.)
The aspect ratio is not adjusted from the original. It is set by the program being watched.
This picture format is 4:3 aspect ratio.
The aspect ratio is not adjusted from the original. Used in PC mode.
(Only HDMI/ DVI PC, RGB PC)
14:9 programs are viewed normally in 14:9 with black bars added to the top and bottom. 4:3 programs are magnified on the top/bottom and left/right sides.
4:3 programes are magnified until they fill the 16:9 screen. The top and bottom will be cut off.
ARC
16:9
Just Scan
Original
4:3
1:1
14:9
Zoom1
Zoom2
MODE
DTV
PC PC
23
User Menus
Adjusting Screen Color
Picture Reset
Return
Picture Mode
,
Color Temperature
, Advanced to the default factory settings.
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
To set
Screen
MENU
Adjust the screen video.
Picture
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
To set
Screen
Auto Config.
Manual Config.
XGA Mode
Reset
To set
MENU
MENU
Auto Config. (RGB PC input only) :
This button is for the automatic adjustment of the screen position, clock and phase. This function is available for analog signals only.
Manual Config. :
If the picture isn't clear after auto adjustment and characters are still trembling, adjust the picture phase manually.
* Phase, Clock function are not available in Component, HDMI/DVI DTV.)
Clock :
To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. This function is available for analog signals only.
Phase :
To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. This function is available for analog signals only.
H-Position :
Moving the screen position horizontally.
V-Position :
Moving the screen position vertically.
H-Size
: Adjust the horizontal size of the screen.
V-Size
: Adjust the vertical size of the screen.
XGA Mode (RGB-PC only). :
For more improved or better picture quality, select the same mode corresponding to computer resolution.
Reset:
Return Manual config. to the default factory settings.
24
User Menus
Adjusting the audio function
Sound
Mode
The best sound tone quality will be selected automatically depending on the video type that you're currently watching.
Audio
Sound Mode
Auto Volume
Balance
Speaker
Clear Voice
Standard
Music
Cinema
Sport
Game
User
MENU
• Clear Voice : By differentiating the human sound range from others,it helps users listen to human voices better.
• Standard : The most commanding and natural audio.
• Music : Select this option to enjoy the original sound when listening to the music.
• Cinema : Select this option to enjoy sublime sound.
• Sport : Select this option to watch sports broadcasting.
• Game : To enjoy dynamic sound when playing a game.
• User : Select this option to use the user-defined audio settings.
User
0.1 0.5 1.5 5.0 10
KHz
MENU
Auto
Volume
To adjust uneven sound volumes across all channels or signals automatically to the most appropriate level. To use this feature, select On.
Balance
Use this function to balance sound from the left and right speakers.
Speaker
You can adjust internal speaker status.
If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
Note
When connected to your computer and the 'Sound
Mode' setting in the audio menu is Clear Voice, Standard, Music, Cinema or Sport, the available menus are Balance, Auto Volume, Speaker.
25
User Menus
Adjusting the timer function
Time
Clock
On/Off Timer
Sleep Time
Auto Sleep
Power On Delay
_ _ : _ _ AM
MENU
Clock
If the current time is incorrect, reset the clock manually.
1) Press the MENU button and then use button to select the Time menu.
2) Press the button and then use button to select the Clock menu.
3) Press the button and then use
4) Press the button and then use button to set the hour(00~23). button to set the minutes(00~59).
On/Off Timer
The off time automatically switches the set to standby at the pre-set time.
1) Press the MENU button and then use button to select the Time menu.
2) Press the button and then use
3) Press the button and then use
4) Press the button and then use
5) Press the button and then use button to select On/Off Timer.
button to set the hour(00~23). button to set the minutes(00~59). button to select On or Off.
Sleep Time
The power is automatically turned off when the time set by a user is passed.
1) Press the MENU button and then use
2) Press the button and then use button to select the Sleep Time menu. button to set the hour(00~23).
3) Press the button and then use button to set the minutes(00~59).
Auto Sleep
If Auto Sleep is active and there is no input signal, the set switches to off mode automatically after 10 minutes.
1) Press the MENU button and then use
2) Press the button and then use button to select the Auto Sleep menu. button to select On or Off.
Power On
Delay
When connecting multiple monitors and turning the power on, the monitors are turned on individually to prevent overload.
Note
In the event of power interruption (disconnection or power failure), the clock must be reset.
Once the on or off time is set, these functions operate daily at the preset time.
Off time function overrides On time function if they are set to the same time.
When On time is operated, input screen is turned on as it was turned off.
26
User Menus
Selecting the options
Language
Key Lock
ISM Method
Option
Language
Key Lock
ISM Method
Power Indicator
Logo Light
DPM Select
Tile Mode
Factory Reset
MENU
To set
To choose the language in which the control names are displayed.
Use the buttons to select On or Off. The monitor can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Key Lock tab to the 'On' position.
In order to unlock it, do the following :
• Push the MENU button on the remote control and set Key Lock to the 'Off' position.
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods could result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the screen for a long period of time.
Normal : Leave on normal if you don't foresee image burn in being a problem.
White wash : White wash fills the screen with solid white. This helps removes permanent images burned into the screen. A permanent image may be impossible to clear entirely with white wash.
Orbiter : May help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes.
Inversion : This function inverts the panel color of the screen. The panel color is automatically inverted every 30 minutes.
Dot Wash : This function moves the black dots of the screen. The black dots is automatically moved every 5 second.
Power Indicator
Use this function to set the power indicator on the front side of the product to
On or Off.
Logo Light
Use this function to set the Logo Light on the front side of the product to On or
Off.
DPM Select
A user can choose to turn the power saving mode on / off.
27
User Menus
Selecting the options
•
To use this function
- Must be displayed with various other products.
- Must be in a function that can be connected to RS-232C or RGB Out
Tile mode
Option
Language
Key Lock
ISM Method
Power Indicator
Logo Light
DPM Select
Tile Mode
Factory Reset
MENU
Tile Mode
H-Size
V-Size
H-Position
V-Position
Reset
Tile ID 1
Natural Off
Off
0
0
< >
< >
It is used to enlarge the screen and also used with several products to view screen.
• Tile Mode
Tile mode and choose Tile alignment and set the ID of the current product to set location.
* Only after pressing the SET button the adjustments made to the settings will be saved.
- Tile mode : row x column ( r = 1, 2, 3, 4,5 c = 1, 2, 3, 4,5)
- 5 x 5 available.
- Configuration of an integration screen is also available as well as configuration of One by one Display.
- Tile mode (product 1 ~ 4) : r(2) x c(2)
row
ID 1
ID 3
ID 2
ID 4 column
28
User Menus
Selecting the options
- Tile mode (product 1 ~ 9) : r(3) x c(3)
row
ID 1 ID 2
ID 4
ID 5
ID 7
ID 8
- Tile mode (product 1 ~ 2) : r(2) x c(1)
row
ID 1
ID 3
ID 6 column
ID 9
ID 2 column
- Tile mode (product 1 ~16) : r(4) x c(4)
row
ID 1
ID 2 ID 3
ID 5
ID 6 ID 7
ID 9
ID 13
ID10
ID 14
ID 11
ID 15
ID 4
ID 8
ID 12
ID 16 column
29
User Menus
Selecting the options
Tile mode
• H-Size
Option
Language
Key Lock
ISM Method
Power Indicator
Logo Light
DPM Select
Tile Mode
Factory Reset
MENU
• V-Size
• H-Position
• V-Position
• Reset
• Tile ID
Tile Mode
H-Size
V-Size
H-Position
V-Position
Reset
Tile ID 1
Natural Off
Off
0
0
< >
< >
Adjust the horizontal size of the screen taking into account the size of the bezel.
Adjust the vertical size of the screen taking into account the size of the bezel.
Moving the screen position horizontally.
Moving the screen position vertically.
Function to initialize and release Tile.
All Tile setting are released when selecting Tile recall and the screen returns to Full screen.
Select the location of the Tile by setting an ID.
• Natural
The image is omitted by the distance between the screens to be naturally shown.
Factory Reset
Select this option to return to the default factory settings.
30
User Menus
Adjust Set ID and check Serial No. and SW version.
Information
Set ID
Serial No.
SW Version
Set ID
Serial No.
SW Version
MENU
You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (1~99) using the button and exit. Use the assigned Set ID to individually control each product using the Product
Control Program.
This menu shows the serial number of the product.
This menu shows the software version.
31
Troubleshooting
No image is displayed
● Is the product power cord connected?
• See if the power cord is properly connected to the outlet.
● Is the power indicator light on?
• See if the power switch is turned on.
• May need service.
● Power is on, power indicator is blue but
the screen appears extremely dark.
• Adjust brightness and contrast again.
• Backlight may need repair.
● the power indicator amber?
• If the product is in power saving mode, move the mouse or press any key.
• Turn both devices off and then back on.
● Does the 'Out of range' message
appear?
• The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual.
* Maximum resolution
RGB : 1920 x 1080 @60Hz
HDMI/DVI : 1920 x 1080 @60Hz
● Does the 'Check signal cable' message
appear?
• The signal cable between PC and product is not connected. Check the signal cable.
• Press the 'INPUT' menu in the remote Control to check the input signal.
'Unknown Product' message appears when the product is connected.
● Did you install the driver?
• Install the product driver, which is provided with the product, or download it from the web site.
(http://www.lge.com)
• See if the plug&play function is supported by referring to the video card user manual.
' Key Lock On' message appears.
● The 'Key Lock On' message
appears when pressing the Menu button.
• The control locking function prevents unintentional
OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button and button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only.)
Note
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz.
32
Troubleshooting
The screen image looks abnormal.
● Is the screen position wrong?
• D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the
Position OSD menu.
• See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the
Control Panel – Display – Setting menu.
● Do thin lines appear on the
background screen?
• D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the
Clock OSD menu.
● Horizontal noise appears or the
characters look blurred.
• D-Sub analog signal – Press the “AUTO” button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the
Phase OSD menu.
● The screen is displayed abnormally.
• The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal.
After-image appears on the product.
● After-image appears when the
product is turned off.
• If you use a fixed image for a long time, the pixels may be damaged quickly. Use the screen-saver function.
33
Troubleshooting
● No sound?
● Sound is too dull.
● Sound is too low.
The audio function does not work.
• See if the audio cable is connected properly.
• Adjust the volume.
• See if the sound is set properly.
• Select the appropriate equalize sound.
• Adjust the volume.
Screen color is abnormal.
● Screen has poor color resolution
(16 colors).
• Set the number of colors to more than 24 bits (true color)
Select Control Panel – Display – Settings – Color
Table menu in Windows.
● Screen color is unstable or mono-
colored.
• Check the connection status of the signal cable.
Or, re-insert the PC video card.
● Do black spots appear on the screen?
• Several pixels (red, green, white or black color) may appear on the screen, which can be attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
The operation does not work normally.
● The power suddenly turned off.
• Is the sleep timer set?
• Check the power control settings.
Power interrupted.
• "CAUTION! FAN STOP!"
If the power is turned off after this message appears, it means that the fan is out of order.
In this case, contact your local service center.
34
Specifications
The product specifications can change without prior notice for product improvement.
M4714C
LCD Panel
Power
47 inches (119.28 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 119.28 cm
0.5415 mm (Pixel Pitch)
Rated Voltage
AC 100-240V~ 50/60Hz 3.0A
Power Consumption
On Mode
Sleep Mode
Off Mode
: 300W Typ.
: ≤ 1W (RGB) / 4W(HDMI)
: ≤ 1W
Dimensions
&Weight
[1]
[2]
H H
W
[3]
D
W
[4]
D
H
H
W
[2] 28.80 kg (63.5 lbs)
[4] 29.55 kg (65.15 lbs)
D
W D
Width x Height x Depth
[1] 111.70 cm (43.98 inches) x 75.78 cm (29.83 inches) x 30.26 cm (11.91 inches)
[2] 111.70 cm (43.98 inches) x 66.10 cm (26.02 inches) x 11.87 cm (4.67 inches)
[1] 111.70 cm (43.98 inches) x 75.78 cm (29.83 inches) x 30.26 cm (11.91 inches)
[2] 111.70 cm (43.98 inches) x 66.10 cm (26.02 inches) x 11.87 cm (4.67 inches)
Net
[1] 32.82 kg (72.35 lbs)
[3] 33.56 kg (74 lbs)
NOTE
Information in this document is subject to change without notice.
35
Specifications
The product specifications can change without prior notice for product improvement.
Video Signal
Input Connector
Environmental
Conditions
Max. Resolution
RGB : 1920 X 1080 @60Hz
HDMI/DVI : 1920 X 1080 @60Hz
– It may not be supported depending on the OS or video card type.
Recommended Resolution RGB : WSXGA 1920 X 1080@60Hz
HDMI/DVI : WSXGA 1920 X 1080 @60Hz
– It may not be supported depending on the OS or video card type.
Horizontal Frequency
RGB : 30 - 83 kHz
HDMI/DVI : 30 - 83 kHz
Vertical Frequency
RGB : 56 - 75 Hz
HDMI/DVI : 56 - 60 Hz
Synchronization Type Composite/Separate/Digital
15-pin
D-Sub type, HDMI (digital), S-Video,
Composite Video, Component, RS-232C
Operational Condition Temperature: 0˚C ~ 40˚C , Humidity: 10% ~ 80%
Storage Condition
Temperature: -20˚C ~ 60˚C , Humidity: 5% ~ 90%
* Applicable only for models that support the speakers
Audio
RMS Audio Output
Input Sensitivity
Speaker Impedance
10W+10W(R+L)
0.7Vrms
8Ω
NOTE
Information in this document is subject to change without notice.
36
Specifications
7
*8
9
*10
1
2
*3
4
*5
6
PC Mode – Preset Mode
Preset mode
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1280 x 720
Horizontal
Frequency
(kHz)
31.469
31.468
31.469
37.5
37.879
46.875
49.725
48.363
60.123
44.772
Vertical
Frequency
(Hz)
70.8
70.8
59.94
75
60.317
75
74.55
60
75.029
59.855
*11
*12
*13
*14
15
*16
*17
Preset mode
1280 x 768
1360 x 768
1366 x 768
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 1080
Horizontal
Frequency
(kHz)
47.7
47.72
47.7
63.981
79.98
65.290
67.5
Vertical
Frequency
(Hz)
60
59.799
60
60.02
75.02
59.954
60
1~17: RGB Mode
* : HDMI/DVI mode
DTV Mode
480i
576i
480p
576p
720p
1080i
1080p
Component
HDMI/DVI(DTV)
o o
X o o o o o o o o o x x
Power Indicator
Mode
On Mode
Sleep Mode
Off Mode
Product
Blue
Amber
-
NOTE
DTV/PC selection on RGB and HDMI/DVI inputs is available for PC resolutions :
640 X 480/60Hz, 1280 X 720/60Hz, 1920 X 1080/60Hz and DTV resolutions : 480p, 720p, 1080p.
37
Regulatory Information cont.
FCC Compliance Statement
This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System.
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
CE Conformity Notice
(for Europe)
Products with the “CE” Marking comply with the EMC
Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compiance with these directives implies conformity to the following European Norms :
• EN 55022 ; Radio Frequency Interference
• EN 55024
• EN 61000-3-2
; Electromagnetic Immunity
; Power Line Harmonics
• EN 61000-3-3
• EN 60950-1
; Voltage Fluctuations
; Product Safety
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
Low Radiation Compliance (MPR II)
This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range.
TCO'99
(TCO'99 applied model only)
Canadian DOC Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations. Cet appareil numérique de la classe B
Congratulations!
You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
01
Regulatory Information cont.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized.
There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy.
What does labelling involve?
The product meets the requirements for the TCO’99 scheme which provides for international and environmental labelling of personal computers and/or displays.
The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and
Statens Energimyndighet (The Swedish National
Energy Administration).
Approval requirements cover a wide range of issues: ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety.
Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered.
Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics.
Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO
Development’s website http://www.tcodevelopment.com
or may be ordered from:
TCO Development
SE-114 94 STOCKHOLM, Sweden
Fax: +46 8 782 92 07
Email : [email protected]
Information regarding TCO’99 approved and labelled products may also be obtained at http://www.tcodevelopment.com
Ecological requirements
Flame retardants
Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes when not disposed of in accordance with strict standards for disposal.
TCO’99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.
TCO’99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. TCO’99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one
02
Regulatory Information cont.
exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. TCO’99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead.
_____________________________________________
* Bio-accumulative is defined as substances which accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
TCO’03
(TCO’03 applied model only)
• Noise emissions
Ecology
• The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001
• Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and
IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
Congratulations!
The display you have just purchased carries the TCO’03
Displays label.
This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
• Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.
Energy
• Energy-saving mode after a certain time – beneficial both for the user and the environment
• Electrical safety
Emissions
• Electromagnetic fields
English
Information for Environmental Preservation
LGE. announced the 'LG Declaration for a Cleaner
Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects.
We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly.
We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors.
Information for recycling
This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use.
LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in
03
Regulatory Information cont.
operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method.
If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG.
We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our ‘green’ policies.
http://www.lge.com/about/environment/html/Recycling.jsp
Deutsch
Informationen zur Erhaltung der Umwelt
Im Jahr 1994 verkündete LGE die 'LG Declaration for a
Cleaner Environment' (LG Erklärung für eine sauberere
Umwelt). Seitdem dient dieses Ideal als führendes Prinzip des Unternehmens. Diese Erklärung war die Basis für die
Durchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die
Überlegungen mit einbezogen wurden.
Wir fördern Aktivitäten zum Schutz der Umwelt und die
Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezüglich Umweltfreundlichkeit gerecht zu werden.
Wir sind darauf bedacht, den Anteil der in unseren
Produkten enthaltenen schädlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden.
Informationen zum Thema Recycling
Dieser Monitor enthält Teile, die umweltschädlich sein können. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er außer Dienst gestellt wurde.
Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere
Rücknahme- und Recyclingsysteme im Einsatz. Viele
Teile werden wieder verwendet und recycelt. Schädliche
Substanzen und Schwermetalle werden durch umweltverträgliche Verfahren behandelt.
Falls Sie mehr über unser Recyclingprogramm erfahren möchten, wenden Sie sich bitte an Ihren lokalen LG-
Händler oder einen Unternehmensvertreter von LG.
Wir richten unsere Firmenpolitik auf eine sauberere
Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres
Unternehmens einfließen lassen. Zusätzliche
Informationen über unsere ‘grüne’ Firmenpolitik erhalten
Sie auf unserer Website.
http://www.lge.com/about/environment/html/Recycling.jsp
Français
Information sur la protection del’environnement
LGE. a publié sa 'Déclaration en faveur d’un environnement plus propre' en 1994 et celle-ci est restée, depuis lors, un principe directeur de notre entreprise.
Cette déclaration a servi de base à notre réflexion et nous a permis de prendre en compte à la fois les aspects
économiques et sociaux de nos activités, tout en respectant l’environnement.
Nous encourageons les activités en faveur de la préservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons au minimum les matières dangereuses qui entrent dans leur composition et l’on ne trouve pas de cadmium, par exemple, dans nos moniteurs.
Information sur le recyclage
Ce moniteur peut contenir des composants qui présentent un risque pour l’environnement. Il est donc important que celui-ci soit recyclé après usage.
LGE. traite les moniteurs en fin de cycle conformément à une méthode de recyclage respectueuse de l’environnement. Nous reprenons nos produits et les recyclons dans plusieurs sites répartis dans le monde entier. De nombreux composants sont réutilisés et recyclés, et les matières dangereuses, ainsi que les métaux lourds, sont traités selon un procédé écologique.
Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un l’un de nos représentants.
Nous voulons agir pour un monde plus propre et croyons au rôle de notre entreprise dans l’amélioration de l’environnement. Pour plus de renseignements sur notre politique “verte”, rendez visite à notre site : http://www.lge.com/about/environment/html/Recycling.jsp
04
Regulatory Information cont.
Italiano
Informazioni per la tutela dell’ambiente
La LGE. ha annunciato nel 1994 la cosiddetta 'LG
Declaration for a Cleaner Environment' (Dichiarazione di
LG a favore di un ambiente più pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attività a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attività a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dell’ambiente riducendo i materiali dannosi presenti nei nostri prodotti.
Ad esempio nei nostri monitor non è presente il cadmio.
Informazioni per il riciclaggio
Il monitor può presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. È importante che il monitor sia riciclato al termine del suo utilizzo.
La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dell’ambiente.
Se si desiderano maggiori informazioni in merito al programma di riciclaggio, è consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG.
Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo più pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica “verde”.
http://www.lge.com/about/environment/html/Recycling.jsp
Espanõl
Información para la conservación medioambiental
LGE. presentó la 'Declaración para un entorno más limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaración es la base que nos ha permitido llevar a cabo tareas que respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, económicos y medioambientales.
Promocionamos actividades orientadas a la conservación del medio ambiente y desarrollamos nuestros productos específicamente para que se ajusten a la filosofía que protege el entorno.
Reducimos al máximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores.
Información para el reciclaje
Este monitor puede contener piezas que entrañen riesgos medioambientales. Es importante reciclar este monitor después de su utilización.
LGE. trata todos los monitores usados siguiendo un método de reciclaje que no daña al entorno. Contamos con diversos sistemas de recuperación y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dañinas y los metales pesados se tratan siguiendo un método que no perjudique al medio ambiente. Si desea obtener más información acerca del programa de reciclaje, póngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca.
Basamos nuestra visión y nuestras políticas en un mundo más limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolución como empresa.
Visite nuestra página Web para obtener más información sobre nuestras políticas ecológicas.
http://www.lge.com/about/environment/html/Recycling.jsp
Português
Informações relacionadas à preservação ambiental
A LGE. anunciou a 'LG Declaration for a Cleaner
Environment' (Declaração da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde então como um princípio administrativo de orientação. A
Declaração é a base que nos tem permitido realizar atividades favoráveis ao ambiente com consideração atenta aos aspectos econômicos, ambientais e sociais.
Promovemos atividades de preservação ambiental e desenvolvemos nossos produtos para englobar
05
Regulatory Information cont.
especificamente o conceito de favorável ao ambiente.
Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, não há cádmio em nossos monitores.
Informações relacionadas à reciclagem
Este monitor pode conter peças que podem representar riscos ao ambiente. É importante que ele seja reciclado após o uso.
A LGE. cuida de todos os monitores descartados através de um método de reciclagem agradável ao ambiente. Há vários sistemas de devolução e reciclagem atualmente em operação no mundo. Muitas peças serão reutilizadas e recicladas e as substâncias nocivas e os metais pesados passarão por tratamento através de um método favorável ao ambiente.
Para obter mais informações sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG.
Definimos nossa visão e nossas políticas relacionadas a um mundo mais limpo selecionando a questão do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informações sobre nossas políticas de meio ambiente.
http://www.lge.com/about/environment/html/Recycling.jsp
Nederlands
Informatie met betrekking tot het behoud van het milieu
LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner
Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden.
Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten.
Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors.
Informatie met betrekking tot recycling
Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled.
LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt.
Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LGvertegenwoordiger of een LG-vestiging.
Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid.
http://www.lge.com/about/environment/html/Recycling.jsp
Russian
»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚
¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡
'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',
ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏ
ÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎË
Ô‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘ËÂ
·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓÏ
‰ÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ Ë
ÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.
Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂ
ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ
‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò
ÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË.
Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı
‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯Ëı
ÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.
»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚
›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,
ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.
06
Regulatory Information cont.
ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂ
ËÒÔÓθÁÓ‚‡Ìˡ.
KÓÔÓ‡ˆËˇ LGE Ô‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚Â
ÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„Ó
ÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ
‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡
ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚
·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ
‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚
·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË
ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.
«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈ
ÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ Í
ÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ
ÍÓÔÓ‡ˆËË LG.
Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ
·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛ
ÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛
Ó Ì‡¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚
ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ: http://www.lge.com/about/environment/html/Recycling.jsp
EPA
(EPA applied model only)
E
NERGY
S
TAR is a set of power-saving guidelines issued by the U.S. Environmental Protection
Agency(EPA).
As an ENERGY STAR Partner LGE U. S.
A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
NOM MARK
(Mexico only)
07
Regulatory Information cont.
WEEE
(for Europe )
English
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.
French
Élimination de votre ancien appareil
1.Ce symbole, représentant une poubelle sur roulettes barrée d'une croix, signifie que le produit est couvert par la directive européenne
2002/96/EC.
2.Les éléments électriques et électroniques doivent être jetés séparément, dans les videordures prévus à cet effet par votre municipalité.
3.Une élimination conforme aux instructions aidera
à réduire les conséquences négatives et risques
éventuels pour l'environnement et la santé humaine.
4.Pour plus d'information concernant l'élimination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures ménagères ou encore la magasin où vous avez acheté ce produit.
Italian
Smaltimento delle apparecchiature obsolete
1.Quando su un prodotto è riportato il simbolo di un bidone della spazzatura barrato da una croce significa che il prodotto è coperto dalla direttiva europea 2002/96/EC.
2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorità locali.
3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente.
4.Per informazioni più dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui è stato acquistato il prodotto.
Swedish
Kassering av din gamla apparat
1.När den här symbolen med en överkryssad soptunna på hjul sitter på en produkt innebär det att den regleras av European Directive
2002/96/EC.
2.Alla elektriska och elektroniska produkter bör kasseras via andra vägar än de som finns för hushållsavfall, helst via för ändamålet avsedda uppsamlingsanläggningar som myndigheterna utser.
3.Om du kasserar din gamla apparat på rätt sätt så bidrar du till att förhindra negativa konsekvenser för miljön och människors hälsa.
4.Mer detaljerad information om kassering av din gamla apparat kan får av kommunen, renhållningsverket eller den butik där du köpte produkten.
Dutch
Uw oude toestel wegdoen
1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn
2002/96/EC.
2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen.
3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen.
08
Regulatory Information cont.
4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht.
Finnish
Vanhojen laitteiden hävittäminen
1.Tämä merkki tuotteessa tarkoittaa, että tuote kuuluu sähkö- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan.
2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseen keräyspisteeseen.
3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.
4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin, kierrätyskeskukseen tai myymälään, josta ostit laitteen.
German
Entsorgung von Altgeräten
1.Wenn dieses Symbol eines durchgestrichenen
Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen
Richtlinie 2002/96/EC.
2.Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt werden.
3.Mit der ordnungsgemäßen Entsorgung des alten
Geräts vermeiden Sie Umweltschäden und eine
Gefährdung der persönlichen Gesundheit.
4.Weitere Informationen zur Entsorgung des alten
Geräts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo
Sie das Produkt erworben haben.
Danish
Sådan smider du dit gamle apparat ud
1.Når der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC.
2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjælp af specielle indsamlingsfaciliteter, der er organiseret af staten eller de lokale myndigheder.
3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger på miljøet og menneskelig sundhed.
4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fås ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du købte produktet.
Greek
∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜
1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜
‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓ
ηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.
2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓ
ÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿ ·fi Ù· ÁÂÓÈο
ÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓ
ÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜
¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘ
ÙÔÈΤ˜ ·Ú¯¤˜.
3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·
‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓ
ˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.
4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ
·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂ
ÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ
·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·ÙÂ ÙÔ
ÚÔ˚fiÓ.
Spanish
Cómo deshacerse de aparatos eléctricos y electrónicos viejos
1.Si en un producto aparece el símbolo de un contenedor de basura tachado, significa que éste se acoge a la
Directiva 2002/96/CE.
2.Todos los aparatos eléctricos o electrónicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a través de puntos de recogida designados por el gobierno o las autoridades locales.
3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pública.
4.Para obtener más información sobre cómo deshacerse de sus aparatos eléctricos y electrónicos viejos, póngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquirió el producto.
09
Regulatory Information cont.
Portuguese
Slovak
Hungarian
Polish
Czech
Croatian
10
Regulatory Information cont.
Estonian
Latvian
Lithuanian
11
advertisement
Related manuals
advertisement