Active Platforms
Copper Cable Management Solution
Installation Instructions
ADCP-80-376 • Issue 1 • 10/2008
Introduction
The Copper Cable Management Solution provides cable management functions for active or passive electrical equipment
mounted in a single frame or enclosure. The Copper Cable Management Solution is designed for use with the frame/
enclosure and active equipment specified in step 1. This publication provides instructions for installing and using the
Copper Cable Management Solution.
Verify cable management components
Verify frame/enclosure and dimensions
1
The copper optic cable management solution
is designed for installation with the frame/
enclosure and equipment specified below. Verify
dimensions before starting the installation.
Frame/Enclosure
2
The cable management components required for
this procedure are shown below. Verify that all the
components are available in the specified quantities.
Active Equipment
CCR* 700 series
APC® Netshelter® SX
CISCO® 6509
*Custom Cabinets and Racks, Inc.
NOTE:
Doors, side panels, and other accessories
are not shown. Contact the frame/
enclosure manufacturer for details.
FMX-SSRK-001 (1)
Top Slack
Storage Panel
28 INCHES MIN.
36 INCHES MIN.
RGS-V0ACC0010 (4)
Riser for CC&R Frame
or
RGS-V0ACC0011 (3)
RGS-V0ACC0012 (1)
Riser for APC Frame
42 RU MIN.
FMX-SSRK-002 (1)
Bottom Slack
Storage Panel
FGS-KTW4-W (1)
FiberGuide®
Raceway
PP48AC6T (8)
ADC® TrueNet®
Patch Panel
RGS-VC0012-B (3)
Cable Ring
FRONT
1438954 Rev A
22960-A
FMX-6509VCG-01 (1)
Vertical Cable Guide
RGS-VC0011-B (14)
Cable Ring
22770-A
Page 1
© 2008, ADC Telecommunications, Inc
ADCP-80-376 Issue 1 10/2008
3
Adust the frame/enclosure’s front and rear
vertical mounting flanges.
Adjust the front and rear mounting flanges to the
dimensions specified in the table and drawings.
Frame/Enclosure
Dimension A Dimension B
CCR* 700 series
9.00 in
16.25 in
APC Netshelter SX
10.50 in
16.25 in
®
®
4
Install the right and left side riser panels
Install the right and left side riser panels in the
locations shown. Secure panels to frame/enclosure
using the fasteners provided with the riser panel.
Refer to the installation drawing provided with the
riser panel for the mounting details.
*Custom Cabinets and Racks, Inc.
NOTE:
The spacing for the front flanges is critical
or it will be impossible to mount the front
riser panels in the recommended location.
In addition, the cable management, access,
and fill capacity will be insufficient.
RIGHT SIDE
RISER PANELS
RGS-V0ACC0010
for CC&R Frame
RGS-V0ACC0011
for APC Frame
REAR
Top view of frame.
Placement of active
equipment shown in grey.
REAR FLANGES
B
FRONT
FRONT FLANGES
A
FRONT
TOP LEFT SIDE
RISER PANEL
RGS-V0ACC0010
for CC&R Frame
RGS-V0ACC0011
for APC Frame
REAR
MOUNTING
FLANGES
BOTTOM LEFT SIDE
RISER PANEL
RGS-V0ACC0010
for CC&R Frame
RGS-V0ACC0012
for APC Frame
FRONT
MOUNTING
FLANGES
FRONT
22990-A
FRONT
Page 2
© 2008, ADC Telecommunications, Inc
22961-A
ADCP-80-376 Issue 1 10/2008
5
Install the bottom slack storage panel.
6
Install the active equipment in the mounting space
above the bottom slack storage panel. Place active
equipment as close to storage panel as possible.
Follow the mounting instructions provided by the
manufacturer.
Install the bottom slack storage panel in the lower
part of the frame/enclosure. Adjust position of the
panel to provide the spacing specified in the table
and drawings. Use screws and washers provided to
secure panel to mounting flanges.
Frame/Enclosure
Install the active equipment.
Dimension A
CCR* 700 series
11.25 in
APC® Netshelter® SX
9.50 in
*Custom Cabinets and Racks, Inc.
ACTIVE EQUIPMENT
INSTALLED IN THE
FRAME/ENCLOSURE
BOTTOM SLACK
STORAGE PANEL
FMX-SSRK-002
BOTTOM SLACK
STORAGE PANEL
FRONT
7
FASTENERS
FOR PANEL
22992-A
Install vertical cable guide
Install the vertical cable guide (VCG) on the
lower right side of the frame/enclosure. Remove
screws and washers from the active equipment
mounting bracket as needed. Use the screws and
washers provided with the VCG to secure the VCG
to the lower right mounting flange.
DETAIL SHOWING
INSTALLED VERTICAL
CABLE GUIDE
FMX-6509VCG-01
VERTICAL
CABLE
GUIDE
A
BOTTOM OF
MOUNTNG FLANGE
22967-A
FRONT
23015-A
Page 3
© 2008, ADC Telecommunications, Inc
ADCP-80-376 Issue 1 10/2008
8
Install patch panels
9
Install the eight patch panels in the mounting
spaces directly above the active equipment. Use
the screws and washers provided to secure each
panel to the frame/enclosure mounting flanges.
Install the top slack storage panel
Install the top slack storage panel in the top part
of the frame/enclosure. Use screws and washers
provided to secure panel to the frame/enclosure
mounting flanges.
FMX-SSRK-001
TOP SLACK
STORAGE PANEL
PP48AC6T
PATCH PANEL
FASTENERS
FOR PANELS
FASTENERS
FOR PANELS
TOP SLACK
STORAGE PANEL
INSTALLED IN FRAME
PATCH PANELS
EIGHT PATCH PANELS
INSTALLED IN FRAME
ACTIVE
EQUIPMENT
Page 4
© 2008, ADC Telecommunications, Inc
FRONT
23034-A
FRONT
23036-A
ADCP-80-376 Issue 1 10/2008
10
Installation and removal procedure for all
cable rings.
All cable rings mount on the riser panels. The
drawings show how to install or remove the cable
rings. Refer to this procedure when completing
steps 11 through 13.
NOTE:
11
Install upper front cable rings
Install six cable rings on the upper left front riser
next to patch panels 1, 2, 3, 4, 6, and 7. Install
three cable rings on the upper right front riser next
to patch panels 1, 4, and 7. Install each cable ring
as close to the frame/enclosure mounting flange
as possible.
Mounting plate shown without
cable retention feature for clarity.
INSTALLATION PROCEDURE
a
UPPER LEFT
FRONT RISER
UPPER RIGHT
FRONT RISER
Align tabs in mounting plate
with slots in riser panel.
RGS-VC0011-B
CABLE RING
b
Insert tabs into slots and
rotate plate downward.
RGS-VC0012-B
CABLE RING
c
Snap mouting plate into
riser panel making sure
snapping feature on plate
locks into slot in riser panel.
SNAPPING FEATURE
REMOVAL PROCEDURE
1
1
2
2
3
Insert screwdriver under snapping
feature and push up until snapping
feature is released from slot.
Rotate plate upward and remove.
22704-B
SNAPPING
FEATURE
4
1
3
4
4
5
6
6
7
7
PATCH
PANELS
7
8
FRONT
23037-A
Page 5
© 2008, ADC Telecommunications, Inc
ADCP-80-376 Issue 1 10/2008
12
Install lower front cable rings
13
Install four cable rings on the lower left front riser.
Place the first two rings next to linecard slots 1 and
6. Place the third ring just below slot 9. Place the
fourth ring even with the top edge of the bottom
storage panel. Install each cable ring as close to
the frame/enclosure mounting flange as possible.
Install top rear cable rings
Install four cable rings on the top left rear riser.
Locate rings so they are equally spaced on the
riser. Install each cable ring as close to the frame/
enclosure mounting flange as possible.
UPPER LEFT
REAR RISER
RGS-VC0011-B
CABLE RING
LOWER LEFT
FRONT RISER
RGS-VC0011-B
CABLE RING
REAR
LINECARD
SLOTS
SLOT 1
SLOT 2
SLOT 3
SLOT 4
SLOT 5
SLOT 6
SLOT 7
SLOT 8
SLOT 9
SPACE RINGS
EQUALLY ON
REAR RISER
BOTTOM
EDGE
OF SLOT 9
TOP EDGE
OF PANEL
FRONT
Page 6
© 2008, ADC Telecommunications, Inc
23040-A
REAR
23043-A
ADCP-80-376 Issue 1 10/2008
14
Install FiberGuide mounting brackets
15
Install the five FiberGuide mounting brackets on
the top right riser. Threaded holes are provided
on the front edge of the riser for attaching the
brackets. Secure each bracket to the riser using
the mounting screws provided.
Install FiberGuide raceway
Install the FiberGuide raceway on the FiberGuide
mounting brackets. A threaded hole is provided
on the tab that extends from each bracket for
attaching
theAraceway.
Secure
to the five
Route
Zone
fiber cables
to raceway
frame/enclosure
brackets
using
the cable
screwsclamp
provided.
and
secure
with
assembly
Route the Zone A fiber cables to the top of the
frame/enclosure and secure with the cable clamp
assemblies. Use cables that are terminated with
appropriate connectors. From the cable clamps,
route the fiber cables downward through the center
fiber rings and then upward to the clamp side of
the Zone A fiber panel.
THREADED HOLE
THREADED
HOLES ON
EDGE OF RISER
IN BRACKET
MOUNTING
BRACKET
DETAIL OF BRACKET
INSTALLATION
DETAIL OF RACEWAY
INSTALLATION
UPPER RIGHT
FRONT RISER
23039-C
NOTE: Shown with right front edge of
frame/enclosure removed for clarity.
NOTE: Shown with right front edge of
frame/enclosure removed for clarity.
23041-B
FGS-KTW4-W
FIBERGUIDE
RACEWAY
Page 7
© 2008, ADC Telecommunications, Inc
ADCP-80-376 Issue 1 10/2008
Install flexible tubing
16
18
Install the flexible tubing for fiber optic patch cords
at the top of the FiberGuide raceway. Slide the
tubing into the holder at the top of the raceway.
Route tubing to fiber optic equipment location.
Connect linecard ports to patch panel ports
with jumper patch cords
Connect the linecard ports to the patch panel ports
using 10 foot jumper patch cords. Observe the
routing shown in the diagram. All patch cords route
to the right from the linecards. Zone A patch cords
(red) route to the top storage panel. Zone B patch
cords (blue) route to the bottom storage panel.
TUBING
ZONE A
STORAGE
HOLDER
DETAIL OF TUBING
INSTALLATION
PATCH PANELS
ZONE A
PATCH PANELS
ZONE B
23042-B
NOTE: Shown with right front edge of
frame/enclosure removed for clarity.
17
Route optical fibers to supervisor card
LINECARDS
ZONE A
LINECARD
LINECARD
LINECARD
LINECARD
LINECARDS
ZONE B
LINECARD
LINECARD
LINECARD
LINECARD
Route optical fibers through the FiberGuide raceway
and VCG fiber tray to the supervisor card.
RACEWAY
SUPERVISOR
CARD
ZONE B
STORAGE
23038-A
ADC, ADC Telecommunications, TrueNet, and FiberGuide are registered
trademarks of ADC Telecommunications, Inc..
APC and NetShelter are registered trademarks of American Power Conversion
Corp.
23044-C
VCG
FIBER
TRAY
CISCO is a registered trademark of CISCO Technology, Inc.
ADC Telecommunications, Inc.
PO Box 1101, Minneapolis, MN 55440-1101, USA
1-800-366-3891, Ext: 73475
www.adc.com
Technical Assistance Center (TAC)
[email protected]
© 2008, ADC Telecommunications, Inc.
All Rights Reserved
Page 8
">
