RIDGID R5010 Hammer/Pulse Drill Návod k použití

OPERATOR'S MANUAL
HAMMER/PULSE DRILL
®
R5010
Your new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a Ridgid product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
Introduction ............................................................................................................................................................... 2
General Safety Rules ............................................................................................................................................ 3-4
Specific Safety Rules ................................................................................................................................................ 4
Symbols .................................................................................................................................................................... 5
Specifications ........................................................................................................................................................... 6
Electrical ................................................................................................................................................................... 6
Unpacking ................................................................................................................................................................. 7
Applications .............................................................................................................................................................. 7
Features ................................................................................................................................................................... 8
Operation ............................................................................................................................................................. 9-14
Maintenance ........................................................................................................................................................... 15
Warranty ................................................................................................................................................................. 16
Customer Service Information ................................................................................................................................ 18
INTRODUCTION
Your drill has many features for making the use of this product more pleasant and enjoyable. Safety, performance,
and dependability have been given top priority in the design of this product making it easy to maintain and operate.
WARNING:
Do not attempt to use this product until you thoroughly read and completely understand the operator’s manual.
Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use your product
properly and only as intended, you will enjoy years of safe, reliable service.
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
The operation of any tool can result in foreign objects being thrown into your eyes, which can result in severe
eye damage. Before beginning operation, always wear safety goggles or safety glasses with side shields
and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI
Z87.1.
2
GENERAL SAFETY RULES
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on, invites accidents.
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not use on a ladder or unstable support.
Loose clothes, jewelry, or long hair can be drawn
into air vents.
Work Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools may create sparks
which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical Safety
Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug
in any way. Double insulation
eliminates the need
for the three-wire grounded power cord and grounded
power supply system.
Avoid body contact with grounded surfaces, such
as pipes, radiators, ranges, and refrigerators. There
is an increased risk of electric shock if your body is
grounded.
Tool Use and Care
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused
by poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may become hazardous when
used on another tool.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately.
When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These
cords are rated for outdoor use and reduce the risk of
electric shock.
Damaged cords increase the risk of electric shock.
Personal Safety
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
3
GENERAL SAFETY RULES
Service
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create
a risk of electric shock or injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the
operator.
Additional Safety Rules
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
Protect your lungs. Wear a face or dust mask if
the operation is dusty. Following this rule will reduce
the risk of serious personal injury.
Protect your hearing. Wear hearing protection during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged,
have repaired at your nearest Authorized Service
Center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or
fire.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center. Following this rule will reduce the risk
of shock, fire, or serious injury.
Make sure your extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least
16 is recommended for an extension cord 50 feet
or less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Inspect for and remove all nails from lumber before using this tool. Following this rule will reduce
the risk of serious personal injury.
Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or any
medication. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.
Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges. Following this rule will reduce the risk of electric shock or
fire.
4
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
No Load Speed
Rotational speed, at no load
Class II Construction
Double-insulated construction
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Safety Alert
Precautions that involve your safety
Eye Protection
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Wet Conditions Alert
Do not expose to rain or use in damp locations.
n0
.../min
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL
MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
Important: Advises you of important information or instructions vital to the operation or maintenance of
the equipment.
Note: Advises you of additional information concerning the operation or maintenance of the equipment.
5
SPECIFICATIONS
Chuck Capacity ......................................................................................................................................... 1/2 in. (13 mm)
Input ................................................................................................................... 120 Volts, 60 Hz, AC only, 9.0 amperes
Switch ....................................................................................................................................................... Variable Speed
Hammer Speed ........................................................................................................................................ 0 - 57,000 BPM
No Load Speed ................................................................................................ Low (0 - 1000/min) & High (0 - 3000/min)
ELECTRICAL
Double Insulation
Extension Cords
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting
insulation. Double insulated tools do not need to be
grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting
in overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is
designated with "WA" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
The double insulated system is intended to protect the user from shock resulting from a break in
the tool's internal wiring. Observe all normal safety
precautions to avoid electrical shock.
**Ampere rating
(on tool faceplate)
Important: Servicing of a tool with double insulation
requires extreme care and knowledge of the system and
should be performed only by a qualified service technician.
For service, we suggest you return the tool to your nearest
authorized service center for repair. Always use original
factory replacement parts when servicing.
0-2.0
Cord Length
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0 12.1-16.0
Wire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
—
Electrical Connection
**Used on 12 gauge - 20 amp circuit.
The drill has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz,
AC only (normal household current). Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
your tool does not operate when plugged into an outlet,
double-check the power supply.
CAUTION:
Keep the extension cord clear of the working
area. Position the cord so that it will not get caught
on lumber, tools or other obstructions while you
are working with a power tool.
WARNING:
Check extension cords before each use. If damaged replace immediately. Never use tool with a
damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
6
UNPACKING
Instructions
Packing List
Your drill has been shipped completely assembled.
Carefully remove the tool from the box.
Make sure that all items listed in the packing list are
included.
Inspect the tool carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
tool.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
Hammer Drill with Auxiliary Handle Assembly
Depth Gauge Rod
Carrying Case
Operator’s Manual
WARNING:
If any parts are missing do not operate this tool
until the missing parts are replaced. Failure to do
so could result in possible serious personal
injury.
WARNING:
This tool should never be connected to a power
supply when you are assembling parts, making
adjustments, cleaning, performing maintenance,
or when the tool is not in use. Disconnecting the
tool will prevent accidental starting that could
cause serious injury.
APPLICATIONS
(Use only for the purpose listed below)
Hammer drilling in concrete, brick, or other masonry.
Drilling in wood.
Drilling in ceramics, plastics, fiberglass, and laminates.
Drilling in both soft and hard metals.
Driving screws with screwdriver bits, using driving accessories.
Mixing paint.
7
FEATURES
Before using this product, familiarize yourself with all
operating features and safety requirements. However, do
not let familiarity with the tool make you careless.
AUXILIARY HANDLE ASSEMBLY
An auxiliary handle is installed on the hammer drill. For
ease of operation, you may use the handle with either the
left hand or the right hand.
WARNING:
REVERSIBLE
Exercise caution when using this tool. Careless
actions, for even a fraction of a second, can result
in serious personal injury.
This hammer drill allows you to reverse the bit rotation. You
can control the direction with the switch located on the side
of the tool.
PULSE MODE DRILLING
Your new tool is equipped with the following features. See
Figure 1.
Allows for working with damaged screw heads,
countersinking screws in wood, unscrewing very tight
screws, and starting a drill bit on hard, smooth surfaces.
SWITCH
Your hammer drill has a conveniently located trigger
switch.
DEPTH GAUGE ROD
A depth gauge rod is installed on the auxiliary handle
assembly to assist you in controlling the depth of drilled
holes.
FORWARD-REVERSE
LEVER
KEYLESS CHUCK
SWITCH
TRIGGER
LOCK-ON
BUTTON
Fig. 1
WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is
sufficient to inflict severe injury.
8
OPERATION
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating this tool. Failure to do
so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in
possible serious injury.
SWITCH
See Figure 2.
To turn your drill ON, depress the switch trigger. Release
switch trigger to turn your drill OFF.
LOCK-ON BUTTON
See Figure 2.
Your drill is equipped with a lock-on feature, which is
convenient when continuous drilling for extended periods
of time is required. To lock-on, depress the switch trigger,
push in and hold the lock-on button located on the side of
the handle, then release switch trigger. Release lock-on
button and your drill will continue running.
To release the lock, depress the switch trigger and release.
If you have the lock-on feature engaged during use and
your drill becomes disconnected from power supply,
disengage the lock-on feature immediately.
SWITCH TRIGGER
LOCK-ON
BUTTON
Fig. 2
CHUCK BODY
RELEASE
(UNLOCK)
KEYLESS CHUCK
See Figure 3.
Your new drill has a keyless chuck. As the name implies,
you can hand tighten or release drill bit in the chuck jaws.
Grasp the chuck collar and rotate it to the left. Release the
collar and then turn the chuck body to the right. The arrows
shown in figure 3 indicate which direction to rotate the
chuck body in order to GRIP (tighten) or RELEASE (unlock)
the drill bit.
CHUCK
JAWS
CHUCK
COLLAR
DRILL BIT
WARNING:
GRIP
(TIGHTEN)
Fig. 3
FORWARD
Do not hold the chuck body with one hand and
use the power of the drill to tighten chuck jaws on
drill bit. The chuck body could slip in your hand or
your hand could slip and come in contact with a
rotating drill bit. This could cause an accident
resulting in serious personal injury.
FORWARD-REVERSE
LEVER
REVERSE
REVERSIBLE
See Figure 4.
Your drill has the feature of being reversible. The direction
of chuck rotation is controlled by a switch located on either
side of the drill housing.
The design of the switch will not permit changing the
direction of rotation while the drill is running. Release the
switch trigger and allow the drill to stop before changing its
direction.
Fig. 4
9
OPERATION
VARIABLE SPEED
See Figures 5 & 8.
Your drill has a variable speed dial designed to allow
operator control of speed and torque limits. The speed
and torque of your drill can be increased by turning the
dial on top of the drill.
Avoid running your drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause your drill to become overheated. If this occurs, cool
your drill by running it without a load and at full speed.
The following guidelines may be used in determining
correct speed for various applications:
Low speed is ideal when minimum speed and power is
required. For example, starting holes without center
punching, driving screws, mixing paint, and drilling in
ceramics.
Medium speed is suitable for drilling hard metals,
plastics, and laminates.
High speed produces best results when maximum
power is required. For example, drilling in wood; soft
metals such as aluminum, brass, and copper, and
when using driving accessories.
TO INCREASE SPEED,
PULL SWITCH TRIGGER
Fig. 5
WARNING:
Your drill should never be connected to power
supply when you are assembling parts, making
adjustments, installing or removing drill bits, cleaning, or when not in use. Disconnecting your drill will
prevent accidental starting that could cause serious personal injury.
TWO-SPEED GEAR SHIFT KNOB
See Figure 6.
The hammer drill has a two-speed gear shift knob which
provides a high speed of approximately 3,000 RPM and a
low speed of approximately 1,000 RPM (stated speeds are
with the trigger switch in “Full-On” position).
Fig. 6
WARNING:
WARNING:
Failure to unplug your drill could result in accidental starting causing serious injury.
The hammer drill should never be connected to a
power supply when you are assembling parts,
making adjustments, cleaning, performing
maintenance, or when the tool is not in use.
Disconnecting the tool will prevent accidental starting that could cause serious injury.
For high speed operation, rotate two-speed gear shift knob
clockwise aligning with indicating mark on knob. For low
speed operation, rotate knob counterclockwise with
indicating mark on knob. It may be necessary to rotate the
chuck by hand while rotating knob.
CAUTION:
Never change gears while the tool is running.
Failure to obey this caution could result in serious
damage to the drill.
10
OPERATION
ADJUSTING THE AUXILIARY HANDLE
ASSEMBLY
TO
TIGHTEN
See Figure 7.
Follow these steps to adjust the auxiliary handle assembly.
Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
Rotate the auxiliary handle assembly to the desired
location.
Tighten the auxiliary handle assembly securely by
turning the knob clockwise.
ADJUSTING DRILLING MODE
See Figure 8.
To adjust for type of drilling, slide adjustment button on top
of motor housing hammer mode or drilling mode. For your
convenience a hammer symbol and drill bit symbol have
been molded into adjustment button.
TO
LOOSEN
AUXILIARY HANDLE
ASSEMBLY
HAMMER MODE
Fig. 7
PULSE MODE
WARNING:
Your hammer drill has not been designed for
reverse hammering.
TO INCREASE
TORQUE
We recommend that you use carbide-tipped bits and
select hammer mode when drilling in hard materials such
as brick, tile, concrete, etc.
We recommend that you select normal drill mode when
drilling with twist drills, hole saws, etc., in soft material.
TO DECREASE
TORQUE
VARIABLE
TORQUE DIAL
Pulse mode is activated when rear dial on top of drill is
turned to the circle icon and can be used at any RPM (high
or low speed). Numbers 1 through 6 on the same dial are
the torque settings.
ADJUSTING THE DEPTH GAUGE ROD
See Figure 9.
Follow these steps to adjust the depth gauge rod.
Lock the trigger switch by placing the rotation selector
in the center position.
Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
Adjust the depth gauge rod so that the drill bit extends
beyond the end of the rod to the required drilling
depth.
Tighten the auxiliary handle assembly by turning the
knob clockwise.
DRILLING MODE
TO DECREASE
DRILLING DEPTH
VARIABLE SPEED
DIAL
TO INCREASE
DRILLING DEPTH
Fig. 8
DEPTH GAUGE
ROD
DRILLING
DEPTH
DRILL BIT
AUXILIARY
HANDLE
ASSEMBLY
Fig. 9
11
OPERATION
TO INSTALL BITS
See Figures 10 and 11.
Unplug your drill.
RELEASE
(UNLOCK)
WARNING:
CHUCK JAWS
Failure to unplug your drill could result in accidental starting causing serious injury.
Open or close the chuck jaws to a point where the
opening is slightly larger than the drill bit you intend
to use. Also, raise the front of your drill slightly to keep
the drill bit from falling out of the chuck jaws.
Insert drill bit into chuck the full length of the jaws.
CHUCK
BODY
DRILL BIT
WARNING:
GRIP
(TIGHTEN)
CHUCK
COLLAR
RIGHT
Do not insert drill bit into chuck jaws and tighten as
shown in figure 7. This could cause drill bit to be
thrown from your drill resulting in possible serious
personal injury or damage to your chuck.
Fig. 10
Tighten the chuck jaws on drill bit.
To tighten: grasp the chuck collar and rotate it to the
right. Release the chuck collar and then turn the chuck
body to the left.
Note: Rotate the chuck body in the direction of the
arrow marked GRIP to tighten chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
TO REMOVE BITS
Unplug your drill.
WARNING:
Failure to unplug your drill could result in accidental starting causing serious injury.
WRONG
Fig. 11
Loosen the chuck jaws from drill bit.
To loosen: grasp the chuck collar and rotate it to the left.
Release the chuck collar and then turn the chuck body
to the right.
Note: Rotate the chuck body in the direction of the
arrow marked RELEASE to loosen chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
Remove drill bit from chuck jaws.
12
OPERATION
DRILLING
See Figure 12.
Depress and release switch trigger to be sure your
drill is in OFF position before connecting it to power
supply.
Check the direction of rotation lever for correct
setting (forward or reverse). See Figure 4.
Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
Plug your drill into power supply source.
Hold your drill firmly and place bit at the point to be
drilled.
Depress the switch trigger to start your drill. Do not
lock the switch ON for jobs where your drill may
need to be stopped suddenly.
Move the drill bit into the workpiece applying only
enough pressure to keep the bit cutting. Do not force
your drill or apply side pressure to elongate a hole.
Let your drill and bit do the work.
WARNING:
Be prepared for binding or bit breakthrough. When
these situations occur, drill has a tendency to grab
and kick opposite to the direction of rotation and
could cause loss of control when breaking through
materials. If not prepared, this loss of control can
result in possible serious injury.
Fig. 12
HELPFUL HINTS
When drilling hard, smooth surfaces use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
variable speed feature allows starting holes without center
punching if desired. To accomplish this, operate your drill
at a low speed until the hole is started.
Pulse mode allows you to drill on hard surfaces without a
center punch.
When drilling metals use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit and
increase the drilling action.
If the bit jams in the work piece or if your drill stalls, stop the
tool immediately. Remove the bit from the work piece and
determine the reason for jamming.
WARNING:
Do not force the tool. Forcing the tool can result in
jamming and loss of balance or footing, which
could result in personal injury.
13
OPERATION
CHUCK REMOVAL
See Figure 13.
The chuck must be removed in order to use some
accessories. To remove:
Unplug your drill.
WARNING:
Failure to unplug your drill could result in accidental starting causing serious injury.
Using two open-end wrenches, loosen the chuck. See
Figure 13.
This will loosen the chuck on the spindle. It can now be
unscrewed by hand.
TO RETIGHTEN A LOOSE CHUCK
See Figure 14.
The chuck may at times become loose on the spindle and
develop a wobble. To tighten, follow these steps:
Unplug your drill.
Fig. 13
WARNING:
Failure to unplug your drill could result in accidental starting causing serious injury.
Using two open-end wrenches, tighten the chuck. See
Figure 14.
This will tighten the chuck on the spindle.
Fig. 14
14
MAINTENANCE
GENERAL
LUBRICATION
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
All of the bearings in this tool are lubricated with a sufficient
amount of high-grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further
lubrication is required.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.
come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
Always wear safety goggles or safety glasses
with side shields during power tool operation or
when blowing dust. If operation is dusty, also
wear a dust mask.
It has been found that electric tools are subject to
accelerated wear and possible premature failure when
they are used on fiberglass boats, sports cars, wallboard,
spackling compounds, or plaster. The chips and grindings
from these materials are highly abrasive to electric tool
parts, such as bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be used
for extended work on any fiberglass material, wallboard,
spackling compounds, or plaster. During any use on these
materials, it is extremely important that the tool is cleaned
frequently by blowing with an air jet.
15
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
LIMITED THREE YEAR WARRANTY
AND 90-DAY SATISFACTION GUARANTEE POLICY
This product is manufactured under license from Ridgid,
Inc. by One World Technologies, Inc. All warranty
communications should be directed to One World
Technologies, Inc. at (toll-free) 1-866-539-1710.
90-DAY
POLICY
SATISFACTION
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover
any malfunction, failure or defect resulting from misuse,
abuse, neglect, alteration, modification or repair by other
than an authorized RIDGID service center for hand held
and stationary power tools. One World Technologies, Inc.
makes no warranties, representations or promises as to
the quality or performance of its power tools other than
those specifically stated in this warranty.
GUARANTEE
During the first 90 days after the date of purchase, if you
are dissatisfied with the performance of this RIDGID tool
for any reason you may return the tool to the dealer from
which it was purchased for a full refund or exchange. To
receive a replacement tool you must present proof of
purchase and return all original equipment packaged with
the original product. The replacement tool will be covered
by the limited warranty for the balance of the three year
warranty period.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied
warranties, including warranties of MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE, are
disclaimed. Any implied warranties, including warranties
of merchantability or fitness for a particular purpose, that
cannot be disclaimed under state law are limited to three
years from the date of purchase. One World Technologies,
Inc. is not responsible for direct, indirect, incidental or
consequential damages. Some states do not allow
limitations on how long an implied warranty lasts and/or
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state
to state.
WHAT IS COVERED UNDER THE LIMITED
THREE YEAR WARRANTY
This warranty covers all defects in workmanship or
materials in this RIDGID tool for the three year period from
the date of purchase. This warranty is specific to this tool.
Warranties for other RIDGID products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID tool, you must return it,
freight prepaid, to an authorized RIDGID service center
for hand held and stationary power tools. You may obtain
the location of the authorized service center nearest you
by calling (toll-free) 1-866-539-1710 or by logging on to
the RIDGID website at www.ridgidwoodworking.com.
When requesting warranty service, you must present the
proof of purchase documentation, which includes a date
of purchase. The authorized service center will repair any
faulty workmanship, and either repair or replace any
defective part, at our option at no charge to you.
One World Technologies, Inc.
Hwy. 8
Pickens, SC 29671
16
NOTES
17
OPERATOR'S MANUAL
HAMMER/PULSE DRILL
®
R5010
Customer Service Information
For parts or service, contact your nearest Ridgid authorized service center. Be sure to provide all relevant information
when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit
us online at www.ridgidwoodworking.com.
The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the
space provided below. When ordering repair parts, always give the following information:
Model No.
Serial No.
983000-273
5 -03
R5010
">