advertisement
INTERNATIONAL DESIGN GUIDE
C O N T E N T S
Built-In Refrigeration
Integrated Refrigeration
Wine Storage
Undercounter Refrigeration
4
27
46
63
Features and specifications indicated herein and on our website are subject to change at any time without notice.
Check our website, subzero.com, for the most up-to-date specifications.
I M P O R T A N T N O T E
International models from the factory designed without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct rating for the unit.
If required by local or national codes, the power cord can be easily replaced using the power inlet device.
International models using a factory installed transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. These models will come equipped with
Schuko power cords. The power cord may need to be replaced depending on local and national codes. The USA power cord that is supplied with the product must be disconnected with the appropriate transformer output to be connected in its place.
SUB-ZERO
® is a registered trademark of Sub-Zero Freezer Company, Inc.
The information and images in this guide are the copyright property of
Sub-Zero Freezer Company, Inc.
Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero Freezer Company, Inc.
©Sub-Zero Freezer Company, Inc. all rights reserved.
W E L C O M E T O S U B - Z E R O
We make the ultimate built-in, integrated and undercounter refrigerators, freezers and wine storage units. We offer more solutions to your daily design problems of trying to work the largest appliance into a home without being obtrusive. Placing refrigeration in the home is no longer a problem, but, rather, an opportunity to exercise your creativity.
Sub-Zero has rethought traditional built-in refrigeration, a category it pioneered, with over
60 years of experience. When our complete line of configurations—all refrigerator and all freezer, over-and-under, or side-by-side—are coupled with overlay or stainless steel design alternatives, the result is unlimited flexibility in satisfying your client‘s needs for residential refrigeration.
Created to blend invisibly into your home‘s decor, the Integrated line lets you incorporate refrigeration anywhere in the house—the kitchen, master suite, media room or workout room.
These tall units or two-drawer base refrigerators, freezers and combination units can be hidden inside the furniture or cabinetry of your choosing.
Sub-Zero is breaking with conventional ways of offering Wine Storage for designers and their clients. Our Built-In and Integrated models, along with the free-standing Model I424FS, offer unlimited design and storage capabilities.
Comprehensive installation instructions are shipped with each model. Refer to those instructions in preparing and installing all
Sub-Zero products. These instructions along with product specifications and downloadable
2D and 3D CAD files, as well as pdf files can be found on our website, subzero.com.
C O N T A C T
I N F O R M A T I O N
Website: subzero.com
As you follow these instructions, you will notice warning and caution symbols.
This blocked information is important for the safe and efficient installation of
Sub-Zero equipment. There are two types of potential hazards that may occur during installation.
signals a situation where minor injury or product damage may occur if you do not follow instructions.
states a hazard that may cause serious injury or death if precautions are not followed.
Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation.
3
Model I695/O
Overlay
Model I695/S
Classic
Stainless Steel
B U I L T - I N R E F R I G E R A T I O N
Sub-Zero’s Built-In line offers you the most complete set of design options in built-in refrigeration for all of its models, from the beauty of the overlay models to the professional treatment of the wrapped stainless steel doors.
Glass doors are available on our Models I601R,
I611 and I650. They each come in a framed, overlay and stainless steel design. Model
ICB648PROG also features a glass door in its classic stainless steel look.
In the illustrations, we have shown the two different design configurations of the overlay and stainless steel units applied to Model I695.
Please note how we qualify the different looks with the model number.
Overlay models will come with no handle hardware, because the beauty of this design is that you can match the surrounding cabinetry hardware; however, we do offer optional handles as sales accessories. The new ice and water dispensing Models I685 and I695 are able to accept overlay panels. Overlay models will come with a standard 279 mm panel grille that will accept decorative panel inserts. Models I601R,
I601RG and I601F are only available with the louvered grille. No panel grille option is available.
All stainless steel models are offered in the classic stainless steel finish. Stainless steel models come with a standard 279 mm heavyduty grille, 25 mm diameter stainless steel handles and a stainless steel kickplate.
All grilles will be offered as options in 25 mm increments from 254 mm to 381 mm and can be ordered as sales accessories. Models I601R,
I601RG, I601F, ICB648PRO and ICB648PROG are the exception and are available only with a
279 mm grille.
An important step in assuring a successful plan is to make sure that the actual equipment shipped to your installation site matches the design you have ordered. Each of these design options has specific installation requirements, which means it is vital that the unit match your planning and space needs.
4
B U I L T - I N R E F R I G E R A T I O N
These illustrations represent the full line of
Sub-Zero Built-In models shown in the stainless steel design application with heavy-duty grille. Models ICB648PRO and ICB648PROG are available as built-in or free-standing units in classic stainless steel only.
For information regarding specific Built-In models, refer to the illustrations in this section. Regardless of the specific design application, overlay or stainless steel, the interior specifications of each model are identical.
A L L R E F R I G E R A T O R | A L L F R E E Z E R
914 mm 914 mm 914 mm
1854 mm
1854 mm
1854 mm
M O D E L I 6 0 1 R
All Refrigerator
M O D E L I 6 0 1 R G
All Refrigerator with Glass Door
M O D E L I 6 0 1 F
All Freezer
O V E R - A N D - U N D E R
762 mm 762 mm 914 mm
With the installation of a harness kit, these appliances are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. Models
ICB648PRO and ICB648PROG are
Star-K certified from the factory with no extra wiring harness required. For details about the harness kit, contact your Sub-Zero dealer.
2134 mm
2134 mm
2134 mm
2134 mm
914 mm
M O D E L I 6 1 1 M O D E L I 6 1 1 G with Glass Door
M O D E L I 6 5 0 M O D E L I 6 5 0 G with Glass Door
S I D E - B Y - S I D E
914 mm 1067 mm 1067 mm 1219 mm 1219 mm 1219 mm 1219 mm
2134 mm
2134 mm
2134 mm
2134 mm
2134 mm
2134 mm
2134 mm
M O D E L I 6 6 1 M O D E L I 6 4 2 M O D E L I 6 8 5
Ice | Water
Dispensing
M O D E L I 6 3 2 M O D E L I 6 9 5
Ice | Water
Dispensing
M O D E L
I C B 6 4 8 P R O
Free-Standing or Built-In
M O D E L
I C B 6 4 8 P R O G
Free-Standing or Built-In
Comprehensive installation instructions are shipped with each model. Refer to those instructions in preparing and installing all
Sub-Zero products. The instructions can also be found on our website, subzero.com.
5
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
B U I L T - I N F E A T U R E S
Overlay models blend seamlessly into your overall room design and complement surrounding cabinetry. You add decorative hardware. Overlay models come with a panel grille that will accept decorative panel inserts. The new ice and water dispensing Models I685 and I695 are also available in the overlay application.
Stainless steel models feature wrapped doors,
25 mm diameter stainless steel handles and a heavy-duty grille designed specifically to enhance the aesthetics of today's professional looking kitchens. All Built-In stainless steel models are offered in the classic stainless steel finish.
Dual Refrigeration System. All Built-In combination models have the Sub-Zero dual refrigeration system, which ensures the freshest food and energy efficiency at the same time. You have precise independent control of the refrigerator and freezer compartments. In addition to two compressors, the PRO 48 has three separate evaporators to keep foods fresher longer and prevent odor transfer.
Glass Door. Model I601RG is an all refrigerator unit featuring a glass door. Models I611G and
I650G are over-and-under combination units with a glass door on the refrigerator. These glass door models come in overlay and stainless steel designs. The side-by-side Model ICB648PROG features a glass door on the refrigerator side and comes in classic stainless steel only.
Stainless Steel. The PRO 48 (Models
ICB648PRO and ICB648PROG) feature stainless steel construction inside and out with classic finish for professional strength and beauty.
Ice and Water Dispensing. Models I685 and I695 feature a dispenser that gives you both ice and chilled water through the refrigerator door.
Built-In Design. True cabinet depth design means every inch of the interior is easy to see and to reach. The PRO 48 can be built in or, with the free-standing accessory kit, used in a freestanding application.
Fresh Food. High-humidity crisper drawer with removable dividers is large and deep, with smooth sides for easy cleaning. The top refrigerated drawer on the PRO 48 features a tight-seal, retracting glass crisper lid that keeps produce exceptionally humid and fresh.
Electronic Controls. Up-front touch controls give you digital readings for quick, easy-to-read reference. The microprocessor provides supreme control, accurate to within one degree of preset temperatures, automatic defrosting that senses, then adapts to your use patterns, and a service indicator light. The PRO 48 also features exterior temperature displays.
Advanced Lighting. Bright lighting spreads even illumination throughout the compartment.
The source of the illumination is concealed. The
PRO 48 top LED lights bathe upper compartments in a soft glow. On the refrigerator side, channeled sidewall LEDs can even serve as a door-area night-light for Model ICB648PROG.
Adjustable Shelves. Cantilevered glass shelves make repositioning quick and easy. They are easy to clean, spill proof and steel reinforced for durability. The PRO 48 features glass shelves with stainless steel trim in the refrigerator and
100% stainless steel shelves in the freezer.
Slide-Out Bins. An exclusive PRO 48 feature— these versatile stainless steel bins hold small items, remove easily, and fit neatly under any shelf.
Door Shelves. All door shelves are adjustable for complete flexibility and convenience.
Dairy Storage. Dairy compartment is adjustable, with easy, one-door access, compartment dividers and a clean design. The dairy shelf is magnetically sealed to maintain freshness.
Automatic Ice. Ice maker provides high-quality, crescent-shaped ice that won‘t stick to the side of the glass.
Energy Efficient. Our solid core doors improve insulation and structural integrity. Magnetic gaskets around all doors give extra-tight seals.
Kickplate. Solid, adjustable kickplate gives a true built-in look and conforms to American Institute of Architects standards.
6
M O D E L I 6 0 1 R
A L L R E F R I G E R A T O R
M O D E L I 6 0 1 R G
A L L R E F R I G E R A T O R
W I T H G L A S S D O O R
M O D E L I 6 0 1 F
A L L F R E E Z E R
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I601R/O
I601R/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt (O)
Shipping Wt (S)
914 mm
1854 mm
610 mm
564 L
1848 mm
916 mm
LH or RH
177 kg
191 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I601RG/O
I601RG/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt (O)
Shipping Wt (S)
914 mm
1854 mm
610 mm
569 L
1848 mm
916 mm
LH or RH
181 kg
195 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
Triple-Pane UV Resistant Glass Door
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I601F/O
I601F/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Freezer Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt (O)
Shipping Wt (S)
914 mm
1854 mm
610 mm
547 L
1848 mm
916 mm
LH or RH
171 kg
184 kg
F R E E Z E R F E A T U R E S
Automatic Ice Maker
3 Adjustable Wire Shelves
1 Stationary Glass Shelf
3 Freezer Storage Drawers
5 Adjustable Door Shelves
601RG
M O D E L I 6 0 1 R
All models are shown in the stainless steel design application.
M O D E L I 6 0 1 R G M O D E L I 6 0 1 F
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Side panels in white and classic stainless steel
Full-length framed handles
Decorative overlay handles
90˚ and 105˚ door stop kits
Roll-out deli basket
(Model I601RG)
Dozen egg container with lid
Harness kit for Star-K compliance
7
All models are shown in the stainless steel design application.
M O D E L I 6 1 1
O V E R - A N D - U N D E R
M O D E L I 6 1 1 G
O V E R - A N D - U N D E R
W I T H G L A S S D O O R
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I611/O
I611/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
762 mm
2134 mm
610 mm
360 L
110 L
2108 mm
765 mm
195 kg
210 kg
R E F R I G E R A T O R ( D O O R )
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
Adjustable Roll-Out Deli Basket
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R ( D R A W E R )
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Automatic Ice Maker
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I611G/O
I611G/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
762 mm
2134 mm
Overall Depth 610 mm
Refrigerator Capacity 365 L
Freezer Capacity 110 L
Min Height Required 2108 mm
Door Swing Clearance 765 mm
Shipping Wt (O)
Shipping Wt (S)
214 kg
216 kg
R E F R I G E R A T O R ( D O O R )
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
Triple-Pane UV Resistant Glass Door
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
F R E E Z E R ( D R A W E R )
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Automatic Ice Maker
M O D E L I 6 1 1 M O D E L I 6 1 1 G
8
M O D E L I 6 5 0
O V E R - A N D - U N D E R
M O D E L I 6 5 0 G
O V E R - A N D - U N D E R
W I T H G L A S S D O O R
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I650/O
I650/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
914 mm
2134 mm
610 mm
445 L
139 L
2108 mm
916 mm
219 kg
234 kg
R E F R I G E R A T O R ( D O O R )
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
Adjustable Roll-Out Deli Basket
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R ( D R A W E R )
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Automatic Ice Maker
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I650G/O
I650G/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
914 mm
2134 mm
610 mm
453 L
139 L
2108 mm
916 mm
237 kg
240 kg
R E F R I G E R A T O R ( D O O R )
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
Triple-Pane UV Resistant Glass Door
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
F R E E Z E R ( D R A W E R )
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Automatic Ice Maker
M O D E L I 6 5 0 M O D E L I 6 5 0 G
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Side panels in white and classic stainless steel
Panel, louvered or stainless steel grilles in 25 mm increments from
254 mm to 381 mm high
Full-length framed handles
Decorative overlay handles
Roll-out deli basket
(Models I611G and I650G)
Dozen egg container with lid
Harness kit for Star-K compliance
9
M O D E L I 6 6 1
S I D E - B Y - S I D E
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I661/O
I661/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
914 mm
2134 mm
610 mm
354 L
249 L
2108 mm
527 mm
227 kg
244 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment
1 Storage Drawer
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R F E A T U R E S
Automatic Ice Maker
2 Adjustable Wire Shelves
1 Stationary Solid Shelf
4 Storage Drawers
5 Adjustable Door Shelves
M O D E L I 6 4 2
S I D E - B Y - S I D E
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I642/O
I642/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
1067 mm
2134 mm
610 mm
459 L
232 L
2108 mm
649 mm
245 kg
264 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment
1 Storage Drawer
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R F E A T U R E S
Automatic Ice Maker
3 Adjustable Wire Shelves
1 Stationary Solid Shelf
3 Storage Drawers
5 Adjustable Door Shelves
M O D E L I 6 8 5
S I D E - B Y - S I D E
I C E
|
W A T E R D I S P E N S I N G
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I685/O
I685/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
1067 mm
2134 mm
610 mm
442 L
232 L
2108 mm
649 mm
258 kg
276 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment
1 Storage Drawer
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R F E A T U R E S
Automatic Ice Maker
2 Adjustable Wire Shelves
1 Stationary Wire Shelf
3 Storage Drawers
5 Adjustable Door Shelves
2 Juice Can Shelves
M O D E L I 6 6 1
10
M O D E L I 6 4 2 M O D E L I 6 8 5
M O D E L I 6 3 2
S I D E - B Y - S I D E
M O D E L I 6 9 5
S I D E - B Y - S I D E
I C E
|
W A T E R D I S P E N S I N G
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I632/O
I632/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
1219 mm
2134 mm
610 mm
535 L
278 L
2108 mm
743 mm
264 kg
286 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
2 Storage Drawers
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R F E A T U R E S
Automatic Ice Maker
3 Adjustable Wire Shelves
1 Stationary Solid Shelf
3 Storage Drawers
5 Adjustable Door Shelves
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I695/O
I695/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Wt (O)
Shipping Wt (S)
1219 mm
2134 mm
610 mm
515 L
278 L
2108 mm
743 mm
277 kg
298 kg
R E F R I G E R A T O R F E A T U R E S
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
2 Storage Drawers
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R F E A T U R E S
Automatic Ice Maker
2 Adjustable Wire Shelves
1 Stationary Wire Shelf
3 Storage Drawers
5 Adjustable Door Shelves
2 Juice Can Shelves
M O D E L I 6 3 2 M O D E L I 6 9 5
All models are shown in the stainless steel design application.
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Side panels in white and classic stainless steel
Panel, louvered or stainless steel grilles in 25 mm increments from
254 mm to 381 mm high
Full-length framed handles
Decorative overlay handles
90˚ and 105˚ door stop kits
Dozen egg container with lid
Harness kit for Star-K compliance
11
M O D E L I C B 6 4 8 P R O
S I D E - B Y - S I D E
B U I L T - I N O R F R E E - S T A N D I N G
M O D E L I C B 6 4 8 P R O G
S I D E - B Y - S I D E
W I T H G L A S S D O O R
B U I L T - I N O R F R E E - S T A N D I N G
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Weight
1219 mm
2134 mm
657 mm
521 L
331 L
2121 mm
730 mm
390 kg
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Shipping Weight
1219 mm
2134 mm
657 mm
521 L
331 L
2121 mm
730 mm
397 kg
R E F R I G E R A T O R
(Door and Two Drawers)
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
2 Adjustable Slide-Out Stainless Steel Bins
1 Crisper Lid
Dividers for Drawers Included
F R E E Z E R
(Door and Two Drawers)
Automatic Ice Maker
3 Adjustable Stainless Steel Shelves
1 Stationary Stainless Steel Shelf
1 Stainless Steel Ice Bucket
R E F R I G E R A T O R
(Door and Two Drawers)
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
2 Adjustable Slide-Out Stainless Steel Bins
1 Crisper Lid
Dividers for Drawers Included
Triple-Pane UV Resistant Glass Door
F R E E Z E R
(Door and Two Drawers)
Automatic Ice Maker
3 Adjustable Stainless Steel Shelves
1 Stationary Stainless Steel Shelf
1 Stainless Steel Ice Bucket
A C C E S S O R I E S
Contact your Sub-Zero Dealer
90˚ door stop kit—right or left hinge
Dozen egg container with lid
Slide-out stainless steel refrigerator bin
Refrigerator drawer dividers
Classic stainless steel side panel
Free-standing kit—includes two stainless steel side panels and top lid
M O D E L I C B 6 4 8 P R O
12
M O D E L I C B 6 4 8 P R O G
P L A N N I N G I N F O R M A T I O N
Although the Sub-Zero Built-In line offers a wide range of designs and configurations, the basic planning considerations for all models have much in common. As you integrate Built-In models into your overall plan, review installation requirements for your particular model(s). The
Installation Specifications illustrations provide planning information for all Built-In models— overlay and stainless steel.
Allow the door(s) to open a minimum of 90˚ or you‘ll have problems removing drawers. With the door opening at 90˚, you may have to move drawers slightly to clear the door interior.
For corner installations, allow for a minimum
76 mm filler so that the door can open to 90˚.
If you‘re using raised panels, consider using a wider filler.
When units are installed side by side, a filler strip is recommended. The width of this filler strip will vary depending on the configuration and panels you use.
Be sure to add the filler strip width to your finished rough opening dimension. In any installation of two units side by side without a filler strip, add an additional 13 mm to your combined numbers. This will allow for the proper width.
IMPORTANT NOTE: Refer to the full-scale illustrations at the end of this section for specifics on door openings and filler size alternatives.
E L E C T R I C A L R E Q U I R E M E N T S
International models from the factory designed without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device.
International models using a factory installed transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. These models will come equipped with
Schuko power cords. The power cord may need to be replaced depending on local and national codes. The USA power cord that is supplied with the product must be disconnected with the appropriate transformer output to be connected in its place.
IMPORTANT NOTE: The electrical outlet must be grounded. The outlet must be flush with the back wall. Refer to the Installation Specifications illustration for your model for exact placement.
IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
P L U M B I N G C O N S I D E R A T I O N S
For Built-In models with an automatic ice maker, rough in the water supply line. Connect a
6.35 mm OD copper line to the house supply, being sure to use an easily accessible shut-off valve between the supply and the refrigerator.
Do not use self-piercing valves. A saddle valve kit
(4200880) is available from your Sub-Zero dealer.
For Built-In models, a line filter is required when water conditions have a high sediment content.
The ice maker operates on water pressure of 1.4
bar to 6.9 bar.
IMPORTANT NOTE: In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently.
IMPORTANT NOTE: A reverse osmosis system can be used with Models ICB648PRO and
ICB648PROG, provided there is constant water pressure of 1.4 bar to 8.3 bar supplied to the unit at all times.
The water line should be routed up through the floor within 13 mm from the back wall and no higher than 76 mm off the floor. If you have to come through the wall, make sure the water line is no more than 76 mm from the floor.
Regardless of the routing, allow 1 m of excess copper tubing to remain outside the wall or floor for easy connection to the unit. Refer to Installation Specification illustrations.
M O D E L O P T I O N S
Model I601R
914 mm
All Refrigerator
Model I601RG
914 mm
All Refrigerator with Glass Door
Model I601F
914 mm
All Freezer
Model I611
762 mm
Over-and-Under
Model I611G
762 mm
Over-and-Under with Glass Door
Model I650
914 mm
Over-and-Under
Model I650G
914 mm
Over-and-Under with Glass Door
Model I661
914 mm
Side-by-Side
Model I642
1067 mm
Side-by-Side
Model I685
1067 mm
Side-by-Side
Ice | Water Dispensing
Model I632
1219 mm
Side-by-Side
Model I695
1219 mm
Side-by-Side
Ice | Water Dispensing
Model ICB648PRO
1219 mm
Side-by-Side
Built-In or Free-Standing
Model ICB648PROG
1219 mm
Side-by-Side with Glass Door
Built-In or Free-Standing
13
O V E R A L L D I M E N S I O N S
All Refrigerator | All Freezer Models
A L L R E F R I G E R A T O R
A L L F R E E Z E R
Model I601R
All Refrigerator
Model I601RG
All Refrigerator with Glass Door
Model I601F
All Freezer
1854 mm 1854 mm
914 mm 914 mm
Model I601R
All Refrigerator
Width 914 mm
Height 1854 mm
Depth 610 mm
Model I601RG
All Refrigerator with Glass Door
Width 914 mm
Height 1854 mm
Depth 610 mm
Illustrations shown in stainless steel design.
1854 mm
914 mm
Model I601F
All Freezer
Width 914 mm
Height 1854 mm
Depth 610 mm
610 mm
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
Refer to the fullscale illustrations at the end of this section for specifics on door openings and other specifications.
I N S T A L L A T I O N S P E C I F I C A T I O N S
All Refrigerator | All Freezer Models
Models I601R and I601RG, which do not have an ice maker, will not require the water line connection.
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
10 mm
FRAME
EXTENSION
606 mm
BEHIND
FRAME
90˚
916 mm
610 mm
ROUGH
OPENING
DEPTH
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
(I601F ONLY)
SHUT-OFF
VALVE
TOP VIEW
902 mm
ROUGH OPENING WIDTH
1848 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING
279 mm
LOCATE ELECTRICAL
WITHIN ENTIRE SHADED AREA
LOCATE WATER SUPPLY
WITHIN BOTTOM SHADED
AREA ONLY (I601F ONLY)
610 mm
152 mm
76 mm
E
W
FRONT VIEW
1848 mm
MINIMUM HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
14
O V E R A L L D I M E N S I O N S
Over-and-Under Refrigerator / Freezer Models
2134 mm 2134 mm 2134 mm 2134 mm
O V E R - A N D - U N D E R
Model I611
Model I611G with Glass Door
Model I650
Model I650G with Glass Door
762 mm 762 mm
Model I611
Width 762 mm
Height 2134 mm
Depth 610 mm
Model I611G with Glass Door
Width 762 mm
Height 2134 mm
Depth 610 mm
Illustrations shown in stainless steel design.
914 mm
Model I650
Width 914 mm
Height 2134 mm
Depth 610 mm
914 mm
Model I650G with Glass Door
Width 914 mm
Height 2134 mm
Depth 610 mm
610 mm
I N S T A L L A T I O N S P E C I F I C A T I O N S
Over-and-Under Refrigerator / Freezer Models
Model I611
A) Rough Opening Width
B) Min Door Clearance
Model I611G
A) Rough Opening Width
B) Min Door Clearance
Model I650
A) Rough Opening Width
B) Min Door Clearance
Model I650G
A) Rough Opening Width
B) Min Door Clearance
749 mm
765 mm
749 mm
765 mm
902 mm
916 mm
902 mm
916 mm
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
610 mm
ROUGH
OPENING
DEPTH
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
SHUT-OFF
VALVE
TOP VIEW
178 mm
E
LOCATE ELECTRICAL
WITHIN SHADED AREA
152 mm
2108 mm
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
1918 mm
A
ROUGH OPENING WIDTH
2127 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
76 mm
LOCATE WATER SUPPLY
WITHIN SHADED AREA
457 mm
152 mm
W
FRONT VIEW
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
10 mm
FRAME
EXTENSION
90˚
606 mm
BEHIND
FRAME
B
Refer to the fullscale illustrations at the end of this section for specifics on door openings and other specifications.
15
O V E R A L L D I M E N S I O N S
Side-by-Side Refrigerator | Freezer Models
2134 mm
914 mm 1067 mm 1067 mm 1219 mm
Model I661 Model I642
Width 914 mm
Height 2134 mm
Depth 610 mm
Width 1067 mm
Height 2134 mm
Depth 610 mm
Model I685
Ice | Water Dispensing
Width 1067 mm
Height 2134 mm
Depth 610 mm
Model I632
Width 1219 mm
Height 2134 mm
Depth 610 mm
1219 mm 610 mm
Model I695
Ice | Water Dispensing
Width 1219 mm
Height 2134 mm
Depth 610 mm
Illustrations shown in stainless steel design.
S I D E - B Y - S I D E
Model I661
Model I642
Model I685
Ice | Water Dispensing
Model I632
Model I695
Ice | Water Dispensing
10 mm
FRAME
EXTENSION
90˚
606 mm
BEHIND
FRAME
B
I N S T A L L A T I O N S P E C I F I C A T I O N S
Side-by-Side Refrigerator | Freezer Models
Model I661
A) Rough Opening Width
B) Min Door Clearance
902 mm
527 mm
Model I642
A) Rough Opening Width 1054 mm
B) Min Door Clearance 649 mm
Model I685
A) Rough Opening Width 1054 mm
B) Min Door Clearance 649 mm
Model I632
A) Rough Opening Width 1206 mm
B) Min Door Clearance 743 mm
Model I695
A) Rough Opening Width 1206 mm
B) Min Door Clearance 743 mm
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
16
610 mm
ROUGH
OPENING
DEPTH
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
SHUT-OFF
VALVE
TOP VIEW
178 mm
E
152 mm
LOCATE ELECTRICAL
WITHIN SHADED AREA
2108 mm
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
1918 mm
A
ROUGH OPENING WIDTH
2127 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
76 mm
LOCATE WATER SUPPLY
WITHIN SHADED AREA
457 mm
152 mm
W
FRONT VIEW
O V E R A L L D I M E N S I O N S
PRO 48 Side-by-Side Refrigerator | Freezer Models
2134 mm
606 mm
P R O 4 8
S I D E - B Y - S I D E
Model ICB648PRO
Built-In or Free-Standing
Model ICB648PROG with Glass Door
Built-In or Free-Standing
1219 mm 1219 mm
Model ICB648PRO
Width 1219 mm
Height 2134 mm
Depth 606 mm*
657 mm**
Model ICB648PROG with Glass Door
Width 1219 mm
Height 2134 mm
Depth 606 mm*
657 mm**
*Depth from behind face frame to back of unit for standard installation.
**Depth from front of face frame to back of unit for flush installation.
657 mm
766 mm
I N S T A L L A T I O N S P E C I F I C A T I O N S
PRO 48 Side-by-Side Refrigerator | Freezer Models
Built-In or Free-Standing
Models ICB648PRO and ICB648PROG can be used free-standing or installed as a standard or flush built-in application. For standard built-in installations, the face frame of the unit will extend 51 mm beyond cabinetry.
In flush built-in installations, the front of the face frame will be flush with surrounding cabinetry.
Dimensions are for finished rough openings.
606 mm
BEHIND
FACE
FRAME
521 mm
657 mm
TO FRONT
OF FACE
FRAME
730 mm
ROUGH
OPENING DEPTH
610 mm
STANDARD
660 mm
FLUSH
MIN
1
914 mm
/
4
"
COPPER
WATER LINE
SHUT-OFF
VALVE
TOP VIEW
178 mm
E
152 mm
LOCATE ELECTRICAL
WITHIN SHADED AREA
MIN HEIGHT
REQUIRED
TO FINISHED
FLOORING
(LEVELERS IN)
2121 mm
STANDARD
2127 mm
FLUSH
ROUGH
OPENING HEIGHT
TO FINISHED
FLOORING
2127 mm
STANDARD
2137 mm
FLUSH
ROUGH
OPENING WIDTH
1206 mm STANDARD
1219 mm FLUSH
1918 mm
1219 mm
LOCATE WATER SUPPLY
WITHIN SHADED AREA
76 mm
152 mm
W
132 mm
FRONT VIEW
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
17
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
A N T I - T I P B L O C K I N G K I T
To prevent the unit from tipping forward and to provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 25 mm or less, you won‘t need to block the unit. But for installations with clearances of more than 25 mm, you must block the unit with the anti-tip blocking kit (wood block and hardware) provided with each Sub-Zero Built-In model. Refer to the
Built-In Installation Guide packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly.
A D D I N G P A N E L S
In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install door panels.
Specifications on the following pages provide panel dimensions and installation considerations for overlay door panels.
Side panels can be used with the overlay and stainless steel design applications. Refer to specifications on page 20.
18
O V E R L A Y D O O R P A N E L S
If you and your client have ordered an overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. The overlay panel design option is available on all Built-In units except Models ICB648PRO and
ICB648PROG.
For exact door panel dimensions for Built-In overlay models, refer to the Overlay Panel Specifications on pages 22–23.
The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels—the decorative overlay panel, a 3 mm spacer panel and a 6 mm backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or, more likely, three different panels.
Regardless of the physical construction of the panels (routing or three-panel assembly), you will need to follow the Overlay Panel Specifications on the following pages for exact sizing and panel placement to ensure a proper fit.
Illustration 3 is a cross section view of the threepanel assembly showing placement of the door, drawer or grille trim. Illustration 4 shows a rear view of the three-panel assembly and critical dimensions, standard for all models.
IMPORTANT NOTE: Keep in mind that the
Sub-Zero door panels have the potential for hitting adjacent cabinets and/or countertops when they are opened. You need to be aware of your surrounding cabinetry and space limitations when using the overlay models. Refer to the fullscale illustrations at the end of this section.
If you are using an overlay door panel with
Model I611, I611G, I650 or I650G, it is necessary to rout a space for the unit‘s lower hinge plate so it does not strike the door panel. Refer to illustration 5.
For Models I611, I611G, I650 and I650G, you will minimize the reveal between the bottom of the overlay door panel and the top of the overlay drawer panel. Refer to illustration 6.
IMPORTANT NOTE: If you choose not to rout a space for the lower hinge plate, you can reduce the total height of the overlay panel (decorative panel only) by 13 mm.
P A N E L
R E Q U I R E M E N T S
The overlay door panel assembly must be a minimum of16 mm thick and cannot exceed
23 kg.
Do not exceed the overlay decorative panel dimensions for Models I611, I611G, I650 or
I650G listed on page 22. If you try to make the reveal tighter between the door and drawer panels, the panels may hit when opening and closing, causing possible damage to the panels and the Sub-Zero unit.
Spacer Panel
3 mm Overlay Panel
Overlay Panel
Spacer Panel
Illus. 3
6 mm Backer Panel
8 mm min
4 mm
2 mm
Door / Drawer /
Grille Trim
~ 19
mm
3 mm 6 mm
Backer
Panel
Illus. 4
13 mm
10 mm
Illus. 5
Overlay Panel
6 mm Backer Panel
Spacer Panel
76 mm
Bottom Edge –
Hinge Side
(rear view)
Illus. 6
Overlay Panel
Spacer Panel
Backer
Panel
8 mm
21 mm
13 mm
19
I N S T A L L A T I O N
To install overlay panels, see the detailed procedures outlined in the
Sub-Zero Built-In
Installation Guide.
O V E R L A Y D O O R P A N E L S
For glass door Models I601RG, I611G and I650G, the refrigerator door panel must include a cutout to accommodate the window. Refer to the
Overlay Panel Specifications for Models I601RG,
I611G and I650G on page 22.
IMPORTANT NOTE: On glass door models, the glass portion of the door must be exposed and not covered by any part of the panel.
For Models I685 and I695, the refrigerator door panel must include a cut-out to accommodate the glasswell and bezel. The thickness of the panel in this area can range from 6 mm to a maximum of 29 mm.
IMPORTANT NOTE: Regardless of the thickness of the overlay panel for Model I685 or I695, you must plan for a flat ’landing’ space for the decorative bezel surrounding the glasswell area.
Refer to page 23 for exact cut-out dimensions of the glasswell area in the overlay, spacer and backer panels. This ’landing’ area can be accomplished in a number of different ways. We are showing two in Illustrations 7 and 8 below.
Illustration 7 shows how you can recess the bezel to the inset panel. You must rout out a space to accommodate the 327 mm height of the bezel. Also keep in mind that the amount of material you will rout out of the stile will vary because of the thickness of this element.
However, the width of the stile immediately adjacent to the bezel must be 37 mm. DO NOT cut the entire stile to this dimension. In this illustration you can see that rails above and below the bezel give this a finished look. Make sure that the bezel is not supporting weight from the panel.
Illustration 8 shows how you can box out a landing space for the bezel using stiles and rails to create this space. Again, keep in mind, that the total thickness of the panel at this level must not exceed 29 mm.
O V E R L A Y P A N E L G R I L L E
Overlay grille panels for the panel grille match the design of the door panels. Overlay units, except Models I601R, I601RG and I601F, come standard with an 279 mm panel grille. Optional grilles are available in 25 mm height increments from 254 mm to 381 mm. Overlay grille panel specifications for the panel grille are listed on page 23. Also refer to illustration 4 on page 19 for additional overlay panel dimensions.
Do not exceed the panel dimensions listed for the appropriate overlay grille panel you are specifying. The decorative panel cannot be any larger or it may restrict the airflow to the compressor area and cause problems with the operation of the Sub-Zero unit.
Routing
Required
37 mm
Width of Stile
Adjacent to Bezel
Illus. 7
Glasswell
Cut-Out
327 mm
Height of Bezel 43 mm
Edge of
Panel to
Cut-Out
Illus. 8
20
H A N D L E H A R D W A R E
Overlay models come without handle hardware.
The beauty of this design is that you can match the surrounding cabinet hardware. You or the cabinet manufacturer must provide handle hardware to match the overall decorating scheme.
The handle hardware must be installed before installing the panel assembly. Use larger D-style handles. If screws with thick heads are used, the screws will need to be countersunk into the door before the panel is put into place.
IMPORTANT NOTE: Sub-Zero does not recommend using single pull knobs on any of its Built-
In models.
For overlay Models I685 and I695, mounting placement of the refrigerator door handle must assure proper access to the glasswell and adequate clearance under the handle. Illustration
8 shows placement of the refrigerator door handle in relationship to the glasswell bezel on stainless steel models.
Optional stainless steel handles are available in a variety of diameters and lengths, as are handles to match the color and style of Wolf ovens.
Contact your Sub-Zero dealer for specifics.
Refer to the full-scale illustrations at the end of this section for handle hardware considerations.
S I D E P A N E L S
Side panels can be used with the overlay and stainless steel design applications. When planning for side panels with the installation of a
Built-In model, you need to be aware of space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your unit, the height of the panel will vary.
Cut-outs around the toe kick and grille area are required if a 6 mm thick panel will be inserted into the main frame channel. The panel will need to be 610 mm deep. If a 10 mm thick panel is used, the panel will abut the main frame and should be 606 mm deep. Refer to illustrations
9–11 below for placement of toe kick and grille area cut-outs for your specific model. These dimensions do not apply to Models ICB648PRO and ICB648PROG.
The toe kick area may or may not be cut out depending on the look you want to achieve.
IMPORTANT NOTE: The use of side panels may change the width of your rough opening.
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
I N S T A L L A T I O N
To install overlay panels, see the detailed procedures outlined in the
Sub-Zero Built-In
Installation Guide.
337 mm
6 mm
606 mm
BEHIND FRAME
337 mm
6 mm
606 mm
BEHIND FRAME
25 mm
51 mm
Glasswell
Profile
Handle
Profile
Illus. 8
606 mm
BEHIND FRAME
102 mm
76 mm
Illus. 9—Models I601R,
I601RG and I601F
102 mm
76 mm
Illus. 10—Models I611, I611G,
I650 and I650G
6 mm
102 mm
76 mm
76 mm
Illus. 11—Models I661, I642,
I632, I685 and I695
21
O V E R L A Y D O O R P A N E L S P E C I F I C A T I O N S
All Refrigerator | All Freezer Overlay (O) Models
Model I601R
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
W
875 mm
851 mm
867 mm
H
1505 mm
1481 mm
1497 mm
Model I601RG
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Window Cut-out Dimensions
Window Cut-out Location
Model I601F
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
C)
W
875 mm
851 mm
867 mm
646 mm
114 mm
W
875 mm
851 mm
867 mm
H
1505 mm
1481 mm
1497 mm
1048 mm
D) 343 mm
H
1505 mm
1481 mm
1497 mm
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O) models.
O V E R L A Y D O O R P A N E L S P E C I F I C A T I O N S
Over-and-Under Overlay (O) Models
Model I611
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
W
722 mm
699 mm
714 mm
722 mm
699 mm
714 mm
H
1241 mm
1205 mm
1221 mm
475 mm
451 mm
467 mm
Model I611G
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Window Cut-out Dimensions
Window Cut-out Location
Model I650
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
W
722 mm
699 mm
714 mm
722 mm
699 mm
714 mm
494 mm
C) 114 mm
W
875 mm
851 mm
867 mm
875 mm
851 mm
867 mm
H
1241 mm
1205 mm
1221 mm
475 mm
451 mm
467 mm
1000 mm
D) 127 mm
H
1241 mm
1205 mm
1221 mm
475 mm
451 mm
467 mm
Model I650G
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Window Cut-out Dimensions
Window Cut-out Location C)
W
875 mm
851 mm
867 mm
875 mm
851 mm
867 mm
646 mm
114 mm
H
1241 mm
1205 mm
1221 mm
475 mm
451 mm
467 mm
1000 mm
D) 127 mm
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O) models.
22
W
Models I601R and I601F
H
C
C
C
D
W
Model I601RG
H
H
C
C
C
H
H
W
Models I611 and
I650
D
H
W
Models I611G and
I650G
O V E R L A Y D O O R P A N E L S P E C I F I C A T I O N S
Side-by-Side Overlay (O) Models
Model I661
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Model I642
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Model I685
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Glasswell Cut-out Dimensions
Glasswell Location (Overlay)
Glasswell Location (Spacer)
Glasswell Location (Backer)
Model I632
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
W
494 mm
470 mm
486 mm
379 mm
356 mm
371 mm
W
618 mm
594 mm
610 mm
405 mm
381 mm
397 mm
W
618 mm
594 mm
610 mm
405 mm
381 mm
397 mm
150 mm
E) 43 mm
E) 31 mm
E) 39 mm
W
711 mm
687 mm
703 mm
464 mm
440 mm
456 mm
H
1727 mm
1703 mm
1719 mm
1727 mm
1703 mm
1719 mm
315 mm
F) 730 mm
F) 718 mm
F) 726 mm
H
1727 mm
1703 mm
1719 mm
1727 mm
1703 mm
1719 mm
H
1727 mm
1703 mm
1719 mm
1727 mm
1703 mm
1719 mm
H
1727 mm
1703 mm
1719 mm
1727 mm
1703 mm
1719 mm
Model I695
Refrigerator Overlay Panel
Refrigerator Spacer Panel
Refrigerator Backer Panel
Freezer Overlay Panel
Freezer Spacer Panel
Freezer Backer Panel
Glasswell Cut-out Dimensions
Glasswell Location (Overlay)
Glasswell Location (Spacer)
Glasswell Location (Backer)
W
711 mm
687 mm)
703 mm
464 mm
440 mm
456 mm
150 mm
E)
E)
E)
43 mm
31 mm
39 mm
H
1727 mm
1703 mm
1719 mm
1727 mm
1703 mm
1719 mm
315 mm
F) 730 mm
F) 718 mm
F) 726 mm
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O) models.
For Models I685 and I695, panel thickness in the glasswell area can range from 6 mm to a maximum of 29 mm. If the panel is thicker, you must rout out a minimum 6 mm flat landing area to accommodate the bezel surrounding the glasswell.
O V E R L A Y G R I L L E P A N E L
Overlay (O) Models
Width Dimensions
Models I611 and I611G
Overlay Panel Width
Spacer Panel Width
Backer Panel Width
W
722 mm
699 mm
714 mm
Models I650, I650G, I661
Overlay Panel Width
Spacer Panel Width
Backer Panel Width
W
875 mm
851 mm
867 mm
Models I642 and I685
Overlay Panel Width
Spacer Panel Width
Backer Panel Width
Models I632 and I695
Overlay Panel Width
Spacer Panel Width
Backer Panel Width
W
1027 mm
1003 mm
1019 mm
W
1180 mm
1156 mm
1172 mm
Height Dimensions
254 mm Grille
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
279 mm Grille (standard)
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
305 mm Grille Height
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
330 mm Grille
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
356 mm Grille
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
381 mm Grille
Overlay Panel Height
Spacer Panel Height
Backer Panel Height
H
235 mm
211 mm
227 mm
H
260 mm
237 mm
252 mm
H
286 mm
262 mm
278 mm
H
311 mm
287 mm
303 mm
H
337 mm
313 mm
329 mm
H
362 mm
338 mm
354 mm
For grille panel size, use width dimensions listed for your model and height dimensions for grille option. 279 mm grille is standard.
Panel grille is available for all overlay units except Models I601R, I601RG and I601F.
O V E R L A Y P A N E L S
Panel specifications are for Built-In overlay (O) models.
To install overlay panels, see the detailed procedures outlined in the
Sub-Zero Built-In
Installation Guide.
W W
Models I661, I642 and I632
E
F
H
H
W W
Models I685 and I695
W
Overlay grille panel
H
23
24
P A N E L A N D H A N D L E P R O F I L E – O V E R L A Y A N D S T A I N L E S S S T E E L A P P L I C A T I O N
STANDARD STAINLESS STEEL HANDLE
1"
51 mm
76 mm
32 mm PANEL
25 mm PANEL
19 mm PANEL
16 mm PANEL
13 mm PANEL
6 mm PANEL
6 mm APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR
DOOR
NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE
MUST BE MOUNTED ON PANEL MINIMUM 16 mm THICK.
The full-scale illustration above shows handle placement for the standard stainless steel handle on the wrapped stainless steel door and on overlay panel applications shown in the dashed line.
IMPORTANT NOTE: For overlay applications, the panel must be a minimum of
16 mm thick to support mounting the handle hardware.
For overlay applications, mount door handles close to the opening edge of the door for ease of opening.
P A N E L A N D H A N D L E P R O F I L E – 1 3 0 ˚ D O O R O P E N I N G
The full-scale illustration shows the panel and handle profile for 130˚ door opening with a 51 mm filler strip.
Interference of door panels with handles at maximum door swing may require the use of an optional 90˚ door stop available through your Sub-Zero dealer.
SUB-ZERO UNIT
130˚ DOOR OPENING
WITH 51 mm FILLER STRIP
(TOP VIEW)
SUB-ZERO UNIT
DOOR CLOSED
FILLER STRIP
51 mm
ALLOW FOR FILLER LAP
BEHIND FLANGE
MAIN FRAME
APPROX
PROFILE OF
STAINLESS
STEEL DOOR
AND HANDLE
STANDARD
FRAMED
FULL-LENGTH
HANDLE
32 m m
PANEL
N
E
L
25 m m
PA
19 m m
PANEL
13 m m
PANEL
PANEL
*6 mm
OPTIONAL
FRAMED EXTENDED
FULL-LENGTH HANDLE
DOOR OPEN @ 130˚
OVERLAY PANEL
19 mm THICK
(NOMINAL)
HINGE
*Approximate thickness of wrapped stainless steel door.
25
26
0 mm
6 mm
13 mm
19 mm
25 mm
32 mm
38 mm
44 mm
51 mm
57 mm
63 mm
70 mm
76 mm
83 mm
89 mm
O V E R L A Y P A N E L A P P L I C A T I O N – 9 0 ˚ D O O R O P E N I N G ( T O P V I E W )
The full-scale illustration shows what considerations you need to make for overlay panel applications and how they may interact with adjacent cabinets and
(TOP VIEW)
NOMINAL OVERALL
WIDTH OF SUB-ZERO
SUB-ZERO UNIT
606 mm TO REAR
OF SUB-ZERO
MAIN FRAME
HINGE
DOOR OPEN @ 90˚
DOOR CLOSED
OVERLAY PANEL
19 mm THICK (NOMINAL)
*Approximate thickness of wrapped stainless steel door.
I N T E G R A T E D R E F R I G E R A T I O N
For generations, the Sub-Zero name has been synonymous with built-in refrigeration. With the
Integrated line, we‘ve taken the idea a step further—refrigerators and freezers you can hide anywhere in the house, inside the furniture or cabinetry of your choosing.
Created to blend invisibly into your home‘s decor, the Integrated line lets you integrate refrigeration into the kitchen, master suite, media room or workout room. Available as tall units or two-drawer base units, the Integrated line expands the possibilities for the way you shape your home.
Tall units are 2032 mm high and offered in two different widths—686 mm and 914 mm. The 686 mm wide tall unit can be ordered as an all refrigerator, all freezer or combination refrigerator
(upper cabinet) and freezer (drawers). The 914 mm wide tall unit is offered as an all refrigerator or combination unit. All of these models are 610 mm deep.
Base units are offered in the 686 mm width only.
They can be ordered as an all refrigerator, all freezer or combination refrigerator (top drawer) and freezer (bottom drawer). Base units are 876 mm high and 610 mm deep.
You just need to add whatever beautiful cabinetry you want to use. Optional classic stainless steel panels with tubular handles are available as sales accessories.
For information regarding specific Integrated models, refer to the illustrations in this section.
A L L R E F R I G E R A T O R | A L L F R E E Z E R
686 mm 686 mm
NEW
914 mm
2032 mm
M O D E L I 7 0 0 T R
All Refrigerator
M O D E L I 7 0 0 T F I
All Freezer
O V E R - A N D - U N D E R
686 mm 914 mm
M O D E L I 7 3 6 T R
All Refrigerator
2032 mm
2032 mm
2032 mm
2032 mm
M O D E L I 7 0 0 T C I
Refrigerator | Freezer
M O D E L I 7 3 6 T C I
Refrigerator | Freezer
D R A W E R S
686 mm
876 mm
876 mm
686 mm
2
876 mm
686 mm
2
M O D E L I 7 0 0 B R
All Refrigerator
M O D E L I 7 0 0 B F I
All Freezer
M O D E L I 7 0 0 B C I
Refrigerator | Freezer
Comprehensive installation instructions are shipped with each model. Refer to those instructions in preparing and installing all
Sub-Zero products. The instructions can also be found on our website, subzero.com.
With the installation of a harness kit, tall models are Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. Drawer models are
Star-K certified from the factory with no extra wiring harness required. For details about the harness kit, contact your Sub-Zero dealer.
27
M O D E L I 7 0 0 T R
A L L R E F R I G E R A T O R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Weight
686 mm
2032 mm
610 mm
439 L
2019 mm
648 mm
LH or RH
495 mm
163 kg
R E F R I G E R A T O R F E A T U R E S
Dual Refrigeration
2 Temperature Zones
3 Adjustable Glass Shelves
1 Stationary Shelf
2 Storage Drawers
Removable Crisper Cover
2 Removable Drawer Dividers
Adjustable Deli Drawer
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 3 6 T R
A L L R E F R I G E R A T O R
NEW
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Weight
914 mm
2032 mm
610 mm
595 L
2019 mm
876 mm
LH or RH
495 mm
218 kg
R E F R I G E R A T O R F E A T U R E S
Dual Refrigeration
2 Temperature Zones
3 Adjustable Glass Shelves
1 Stationary Shelf
2 Storage Drawers
Removable Crisper Cover
4 Removable Drawer Dividers
Adjustable Deli Drawer
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 0 0 T F I
A L L F R E E Z E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Freezer Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Weight
686 mm
2032 mm
610 mm
433 L
2019 mm
648 mm
LH or RH
495 mm
163 kg
F R E E Z E R F E A T U R E S
1 Temperature Zone
3 Adjustable Glass Shelves
1 Stationary Shelf
2 Storage Drawers
1 Removable Drawer Divider
4 Adjustable Door Shelves
Automatic Defrost
Automatic Ice Maker
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 0 0 T R
28
M O D E L I 7 3 6 T R M O D E L I 7 0 0 T F I
M O D E L I 7 0 0 T C I
O V E R - A N D - U N D E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Weight
686 mm
2032 mm
610 mm
289 L
144 L
2019 mm
648 mm
LH or RH
495 mm
163 kg
R E F R I G E R A T O R ( D O O R )
Dual Refrigeration
3 Adjustable Glass Shelves
1 Stationary Shelf
Adjustable Deli Drawer
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R ( D R A W E R S )
1 Removable Drawer Divider
Automatic Defrost
Automatic Ice Maker
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 0 0 T C I
M O D E L I 7 3 6 T C I
O V E R - A N D - U N D E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Weight
914 mm
2032 mm
610 mm
383 L
195 L
2019 mm
876 mm
LH or RH
495 mm
218 kg
R E F R I G E R A T O R ( D O O R )
Dual Refrigeration
3 Adjustable Glass Shelves
1 Stationary Shelf
High-Humidity Crisper Drawer with Dividers
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Egg Container
F R E E Z E R ( D R A W E R S )
1 Removable Drawer Divider
Automatic Defrost
Automatic Ice Maker
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
*Optional stainless steel panels and handles are ordered and shipped as sales accessories.
M O D E L I 7 3 6 T C I
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Classic stainless steel front panels
Tubular handles in classic stainless steel
High-humidity crisper drawer and shelf assembly*
Adjustable deli drawer and shelf assembly*
Crisper cover with lid*
Dozen egg container with lid*
Dual installation heater kit
Harness kit for Star-K compliance
*Accessory is not available for every model.
29
M O D E L I 7 0 0 B R
R E F R I G E R A T O R D R A W E R S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Drawer Clearance
Shipping Weight
686 mm
876 mm
610 mm
150 L
864 mm
495 mm
86 kg
R E F R I G E R A T O R F E A T U R E S
1 Temperature Zone
2 Storage Drawers
Removable Crisper Cover
2 Removable Drawer Dividers
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 0 0 B F I
F R E E Z E R D R A W E R S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Freezer Capacity
Min Height Required
Drawer Clearance
Shipping Weight
686 mm
876 mm
610 mm
144 L
864 mm
495 mm
86 kg
F R E E Z E R F E A T U R E S
1 Temperature Zone
2 Storage Drawers
1 Removable Drawer Divider
Automatic Defrost
Automatic Ice Maker
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
M O D E L I 7 0 0 B C I
R E F R I G E R A T O R
D R A W E R S
|
F R E E Z E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Freezer Capacity
Min Height Required
Drawer Clearance
Shipping Weight
F E A T U R E S
2 Temperature Zones
2 Storage Drawers
Removable Crisper Cover
1 Removable Drawer Divider
Automatic Ice Maker
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)*
686 mm
876 mm
610 mm
82 L
59 L
864 mm
495 mm
86 kg
M O D E L I 7 0 0 B R
*Optional stainless steel panels and handles are ordered and shipped as sales accessories.
M O D E L I 7 0 0 B F I
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Front panels in classic stainless steel
Tubular handles in classic stainless steel
Crisper cover with lid*
Dozen egg container with lid*
Dual installation heater kit
*Accessory is not available for every model.
M O D E L I 7 0 0 B C I
30
I N T E G R A T E D F E A T U R E S
All Integrated models accept wood or stainless steel panels. The optional stainless steel panels and handles are available in classic stainless steel at the 2032 mm and 2134 mm height.
Stainless steel panels are ordered and shipped as sales accessories.
Functional Design. These models can be placed anywhere in the home. Think about “point-ofuse refrigeration” when planning where to place your units.
Integrated Design. All Sub-Zero models are 610 mm deep. Tall Integrated units are 2032 mm high and are offered in two different widths—686 mm and 914 mm. All base units are 686 mm wide and 876 mm high.
Microprocessor. The “brains” of the Integrated units, this computer allows the best in temperature control, efficiency and food preservation.
Temperature Zones. On tall refrigerator and combination units, you have the flexibility of having two temperatures within the same unit.
Automatic Defrost. Depending on usage and exact climate, the Integrated unit will adapt to the unique situation and adjust accordingly to offer greater efficiency. Integrated freezer and combination units have an automatic defrost system.
Kickplate. The adjustable solid kickplate meets standards of the American Institute of Architects. The toe kick area for a solid, decorative kickplate is 102 mm high by 76 mm deep. You can show a 254 mm toe kick, but you cannot cover the louvers of the kickplate. If you choose, the kickplate can be painted.
Front Venting. All models have the mechanical equipment in an area below the lower drawer.
The lower drawer panel can extend to cover these louvers, but a removable decorative kickplate cannot cover the fins.
Lighting. Flat to the ceiling, superior lighting provides white, efficient light in cabinet and drawer units.
Door / Drawer Alarm. When activated, if your door or drawer is accidentally left open for more than 30 seconds, an audible alarm will sound.
Spill-Proof Shelves. The cabinet section of the tall units features adjustable spill-proof one-piece glass shelves that are easily removed for cleaning.
Dairy Shelf. This magnetically sealed compartment is fully adjustable on the tall refrigerator and combination units.
Crisper Cover. On the tall and base refrigerator units and the base combination unit, a removable crisper cover is offered for one of the drawer sections.
Deli Drawer. Smaller items are not lost in this handy feature of the Models I700TR and I700TCI.
Available as a sales accessory for Model I736TCI.
Crisper—Model I736TCI. Model I736TCI is equipped with a sealed crisper. It is large and deep, with smooth sides for easy cleaning. The space features removable dividers.
Egg Container. You can store a dozen eggs in this removable egg container with lid in the tall refrigerator and tall combination units.
Ice Maker. An automatic ice maker, providing crescent-shaped ice, is available as an option on the tall and base freezers as well as the tall and base combination units. This optional equipment must be factory installed.
Door Swing. You can choose left or right door swing on the tall units. This option must be ordered when requesting the unit. You cannot reverse the door in the field.
Dual-Action Hinge. An exclusive dual-action hinge is featured on all of the tall units, allowing for a fully integrated look.
Door Stop. On all of the tall units, a 90˚ door stop is built in to the hinge. Normal door swing is 105˚.
Temperature Zones. With the microprocessor in the Integrated models, you have the capability of setting different optimum temperatures.
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
T E M P E R A T U R E Z O N E S
Model I700BR – One zone,
1˚C to 7˚C
Models I700TR and I736TR –
Two zones, 1˚C to 7˚C
Models I700BFI and I700TFI –
One zone, -21˚C to -15˚C
Model I700TFI – One zone,
-21˚C to -15˚C
Model I700BCI – Two zones,
1˚C to 7˚C top drawer;
-21˚C to -15˚C bottom drawer
Models I700TCI and I736TCI –
Two zones, 1˚C to 7˚C cabinet;
-21˚C to -15˚C drawers
31
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
P L A N N I N G I N F O R M A T I O N
Before moving the Integrated unit into place, be sure that the finished opening dimensions, electrical and plumbing locations and minimum door and drawer clearances are accurate. Refer to the
Installation Specifications illustration for your model on the following pages. Be sure your installer has this information before finishing work is completed.
Integrated models without an automatic ice maker will not require the plumbing connections shown in the illustrations.
The height of the tall unit is set at 2032 mm.
You can allow the top of the door panel to exceed this dimension with caution. If you are working with 2134 mm or 2438 mm neighboring panels, you can utilize door panels to match this height. Other critical dimensions regarding the door swing, drawer openings and toe kick clearance are noted in the Overall Dimensions illustrations on the following pages. Also refer to the full-scale illustrations at the end of this section for specifics on door openings and other specifications.
IMPORTANT NOTE: The anti-tip bracket must be installed to prevent the unit from tipping forward.
E L E C T R I C A L R E Q U I R E M E N T S
International models from the factory designed without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device.
International models using a factory installed transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. These models will come equipped with
Schuko power cords. The power cord may need to be replaced depending on local and national codes. The USA power cord that is supplied with the product must be disconnected with the appropriate transformer output to be connected in its place.
IMPORTANT NOTE: The electrical outlet must be grounded. The outlet must be flush with the back wall. Refer to the Installation Specifications illustration for your model for exact placement.
IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Do not use an extension cord or 2-prong adapter. Electrical ground is required.
Do not under any circumstances remove the power supply cord ground prong.
P L U M B I N G C O N S I D E R A T I O N S
For models with an automatic ice maker, rough in the water supply line. Connect a 6.35 mm OD copper line to the house supply, being sure to use an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit.
Do not use self-piercing valves. A saddle valve kit (4200880) is available from your Sub-Zero dealer. An in-line filter is required when water conditions have a high sediment content. The ice maker operates on constant water pressure between 1.4 bar and 6.9 bar.
IMPORTANT NOTE: In some cases, a reverse osmosis water filter system may not be able to maintain the minimum pressure consistently.
The Installation Specifications illustration for your model on the following pages shows the precise placement of the water line. When routing the water through the side walls, you must place the water line within 13 mm of the floor and as close as possible to the back wall.
The line must be routed around the anti-tip bracket so it clears the bracket and the leveling feet of the unit as shown in the top view of the illustration. Regardless of the routing, allow for
686 mm of excess copper tubing to remain outside the wall or floor for easy connection to the unit.
IMPORTANT NOTE: Do not route water supply line in front of the compressor tray. The tray must be slid forward for service.
32
O V E R A L L D I M E N S I O N S
Models I700TR, I700TFI and I700TCI
10 mm
13 mm
337 mm
260 mm
518 mm
DRAWER
MOUNTING DETAIL
876 mm*
1995
mm*
248 mm
102 mm SIDE VIEW
* 13 mm +
FRONT VIEW
114 mm
686 mm
(UNIT DIMENSION)
356 mm
21 mm
TOP OF
ROUGH
OPENING
610 mm
(UNIT DIMENSION)
DOOR
MOUNTING
DETAIL
2032 mm*
FRONT VIEW
DOOR / DRAWER
CLOSED
90˚
657 mm
117 mm*
MAXIMUM DOOR OPENING 90˚ DOOR OPENING
TOP VIEW
* DOOR / DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
I N S T A L L A T I O N
S P E C I F I C A T I O N S
Models I700TR, I700TFI and I700TCI
TOP VIEW
Models without an ice maker will not require the water line connection.
38 mm
635 mm
ANTI-TIP
BRACKET*
343 mm
394 mm 229 mm
WATER LINE
BOTTOM ENTRY
LOCATION
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
686 mm
152 mm
686 mm
38 mm
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
6 mm
330 mm
64 mm
394 mm
229 mm
19 mm
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
76 mm
2032 mm
610 mm
648
mm*
495
mm*
DOOR / DRAWER
CLOSED
TOP VIEW
635 mm
105˚
ANTI-TIP
BRACKET
343 mm
WATER LINE
SIDE ENTRY
LOCATIONS
686 mm
38 mm
ANTI-TIP
BRACKET
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
A L L R E F R I G E R A T O R
A L L F R E E Z E R
Model I700TR
All Refrigerator
Model I700TFI
All Freezer with Ice Maker
O V E R - A N D - U N D E R
Refrigerator | Freezer
Model I700TCI with Ice Maker
M O D E L I 7 0 0 T R
M O D E L I 7 0 0 T F I
M O D E L I 7 0 0 T C I
Overall Dimensions
Width 686 mm
Height 2032 mm
Depth 610 mm
Finished Opening
Width 686 mm
Height 2032 mm
Depth 635 mm*
*The depth of the unit is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 635 mm.
33
A L L R E F R I G E R A T O R
Model I736TR
All Refrigerator
O V E R - A N D - U N D E R
Refrigerator | Freezer
Model I736TCI with Ice Maker 10 mm
O V E R A L L D I M E N S I O N S
Models I736TR and I736TCI
914 mm
(UNIT DIMENSION)
356 mm
33 mm
TOP OF
ROUGH
OPENING
610 mm
(UNIT DIMENSION)
DOOR MOUNTING
DETAIL
2032 mm*
1976
mm*
13 mm
337 mm
518 mm
260 mm
DRAWER MOUNTING
DETAIL
876 mm*
* 13 mm +
FRONT VIEW
248 mm
102 mm SIDE VIEW
DOOR / DRAWER
CLOSED
90˚
610 mm
876
mm*
495
mm*
DOOR / DRAWER
CLOSED
105˚
886 mm
90˚ DOOR OPENING MAXIMUM DOOR OPENING
178
mm*
TOP VIEW
* DOOR / DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
M O D E L I 7 3 6 T R
M O D E L I 7 3 6 T C I
Overall Dimensions
Width 914 mm
Height 2032 mm
Depth 610 mm
Finished Opening
Width 914 mm
Height 2032 mm
Depth 635 mm*
*The depth of the unit is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 635 mm.
I N S T A L L A T I O N
S P E C I F I C A T I O N S
Models I736TR and I736TCI
TOP VIEW
Models without an ice maker will not require the water line connection.
38 mm
635 mm
ANTI-TIP
BRACKET*
457 mm
508 mm 343 mm
WATER LINE
BOTTOM ENTRY
LOCATION
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
914 mm
152 mm
686 mm
38 mm
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
114 mm
6 mm
445 mm
64 mm
508 mm
343 mm
19 mm
76 mm
2032 mm
TOP VIEW
ANTI-TIP
BRACKET
457 mm
WATER LINE
SIDE ENTRY
LOCATIONS
635 mm
34
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
FRONT VIEW
686 mm
38 mm
ANTI-TIP
BRACKET
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
O V E R A L L D I M E N S I O N S
Models I700BR, I700BFI and I700BCI
686 mm
(UNIT DIMENSION)
10 mm
610 mm
(UNIT DIMENSION)
13 mm
337 mm
518 mm
260 mm
DRAWER
MOUNTING DETAIL
* 13 mm +
FRONT VIEW
876
mm*
248 mm
102 mm SIDE VIEW
610 mm
DRAWER CLOSED
495 mm*
657 mm
TOP VIEW
* DRAWER PANEL THICKNESS NOT INCLUDED
D R A W E R S
Model I700BR
All Refrigerator
Model I700BFI
All Freezer with Ice Maker
Model I700BCI
Refrigerator | Freezer with Ice Maker
I N S T A L L A T I O N
S P E C I F I C A T I O N S
Models I700BR, I700BFI and I700BCI
Models without an ice maker will not require the water line connection.
TOP VIEW
38 mm
635 mm
ANTI-TIP
BRACKET*
343 mm
394 mm 229 mm
WATER LINE
BOTTOM ENTRY
LOCATION
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
686 mm
152 mm
686 mm
38 mm
876 mm
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
114 mm
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
6 mm
330 mm
64 mm
394 mm
229 mm
19 mm
76 mm
FRONT VIEW
TOP VIEW
ANTI-TIP
BRACKET
343 mm
WATER LINE
SIDE ENTRY
LOCATIONS
686 mm
635 mm
38 mm
ANTI-TIP
BRACKET
WATER LINE
SIDE ENTRY
LOCATION
SIDE VIEW
M O D E L I 7 0 0 B R
M O D E L I 7 0 0 B F I
M O D E L I 7 0 0 B C I
Overall Dimensions
Width 686 mm
Height
Depth
876 mm
610 mm
Finished Opening
Width 686 mm
Height
Depth
876 mm
635 mm*
*The depth of the unit is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of
635 mm.
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
35
P A N E L
R E Q U I R E M E N T S
Door and drawer panels must be a minimum of 16 mm thick.
The door panel cannot exceed 18 kg and each drawer panel must not exceed 5 kg for 686 mm wide units. For
914 mm wide units, the door panel weight limit is 24 kg and 7 kg for each drawer panel.
C A B I N E T R Y A P P L I C A T I O N S
Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models can be used with framed as well as frameless cabinets. Because of the precise application and the look you may want to achieve, there are important questions you need to answer before ordering panels for the doors/drawers. As you look at styles of cabinets, keep some important facts in mind:
IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You must move the unit back into drywall or bring the cabinets forward to achieve a flush fit.
The height of the door panel can grow beyond
1153 mm and exceed the 2032 mm overall height as long as you stay below the recommended door panel weight limit.
The toe kick clearance can vary with the height of the lower drawer panel; the maximum panel height is 424 mm. You must keep a minimum space of 102 mm clear below the bottom edge of the lower drawer panel so the unit can be properly vented.
We recommend using D-style handles. For the cabinet door, handles must be located near the edge of the panel opposite the hinge, centered top to bottom. Locate handles in the top center area of the drawer panels.
IMPORTANT NOTE: The inside edges of the rough opening, as well as the sides and a portion of the backside of the decorative panels will need to be finished, as they will be exposed when the doors are open.
F R A M E D C A B I N E T R Y
Framed cabinetry applications present you with different questions to address. The illustrations below show common applications of framed cabinetry. These are not meant to be the only alternatives, but are suggestions from designers around the country. Also refer to the full-scale illustrations at the end of this section for specifics on door openings.
NOTE: In the illustrations below, the first width dimension shown is for 686 mm wide units and the second dimension is for 914 mm wide units.
CABINET
FRAME
CABINET
DOOR
SUB-ZERO
UNIT
610 mm
TO WALL
10 mm
REVEAL
DOOR PANEL
686 mm OR 914 mm
Traditional frame – full overlay
(top view)
CABINET
FRAME
CABINET
DOOR
SUB-ZERO
UNIT
610 mm
TO WALL
10 mm
REVEAL
DOOR PANEL
686 mm OR 914 mm
Traditional frame – standard overlay
(top view)
SUB-ZERO
UNIT
610 mm
TO WALL
CABINET
FRAME
CABINET
DOOR
DOOR PANEL
10 mm
REVEAL
686 mm OR 914 mm
Traditional frame – 10 mm offset
(top view)
36
F R A M E D C A B I N E T R Y –
B E A D E D I N S E T A P P L I C A T I O N
The illustration below shows a 686 mm wide
Integrated base or tall unit installed within a framed cabinetry, beaded inset application.
Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings.
CABINET DOOR
TOP VIEW
A
SUB-ZERO
UNIT
610 mm
TO WALL
A
DOOR PANEL
686 mm
679 mm
PANEL WIDTH
38 mm
1216 mm
A) ALL REVEALS ARE 3 mm
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
*DIMENSIONS MAY VARY
6 8 6 m m
W I D E M O D E L S
Installation of a
686 mm wide
Integrated base or tall unit within framed cabinetry.
*Dimensions may vary.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
2624 mm
I N S T A L L A T I O N
To install integrated panels, see the detailed procedures outlined in the
Sub-Zero Integrated
Installation Guide.
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
2032
mm*
38 mm
686 mm
38 mm
FRONT VIEW
B
345 mm
A
B
A
38 mm
383 mm
C
A
102 mm*
876
mm*
102 mm
610 mm
SIDE VIEW
37
F R A M E D C A B I N E T R Y –
B E A D E D I N S E T A P P L I C A T I O N
The illustration below shows 914 mm wide Integrated tall unit installed within a framed cabinetry, beaded inset application. Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings.
9 1 4 m m
W I D E M O D E L S
Installation of a
914 mm wide
Integrated tall unit within framed cabinetry.
*Dimensions may vary.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
CABINET DOOR
TOP VIEW
A
SUB-ZERO
UNIT
610 mm
TO WALL
A
DOOR PANEL
914 mm
908 mm
PANEL WIDTH
A) ALL REVEALS ARE 3 mm
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
*DIMENSIONS MAY VARY
I N S T A L L A T I O N
To install integrated panels, see the detailed procedures outlined in the
Sub-Zero Integrated
Installation Guide.
38 mm
1216 mm
2624 mm
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
2032
mm*
38 mm
914 mm
FRONT VIEW
38 mm
B
345 mm
A
B
A
38 mm
383 mm
C
A
102 mm*
876
mm*
102 mm
610 mm
SIDE VIEW
38
F R A M E L E S S C A B I N E T R Y
The illustrations show hypothetical installations of Integrated base or tall units within frameless cabinetry. Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings.
A
1153 mm
679 mm*
PANEL WIDTH
A
1153 mm
610 mm
A
345 mm
A
424 mm*
102 mm*
TOE KICK
686 mm
FINISHED OPENING
A) ALL REVEALS ARE 3 mm
908 mm*
PANEL WIDTH
876
mm*
2032
mm*
2029
mm*
2032
mm*
2029
mm*
6 8 6 m m
W I D E M O D E L S
Installation of a
686 mm wide
Integrated base or tall unit within frameless cabinetry.
*Dimensions may vary.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
SIDE VIEW
*DIMENSIONS MAY VARY
610 mm
9 1 4 m m
W I D E M O D E L S
Installation of a
914 mm wide
Integrated tall unit within frameless cabinetry.
*Dimensions may vary.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
A
345 mm
A
424 mm*
102 mm*
TOE KICK
914 mm
FINISHED OPENING
A) ALL REVEALS ARE 3 mm
876
mm*
SIDE VIEW
*DIMENSIONS MAY VARY
39
P A N E L C O N S I D E R A T I O N S
The illustrations below provide panel width dimensions for installation of a single tall unit,
686 mm and 914 mm wide models.
Illustrations on the following page provide panel width dimensions for installing two tall units side by side, 686 mm wide models and 914 mm wide models.
I N S T A L L A T I O N
To install integrated panels, see the detailed procedures outlined in the
Sub-Zero Integrated
Installation Guide.
6 8 6 m m
W I D E M O D E L S
Panel width dimensions for installation of a 686 mm wide tall unit.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into drywall or bring the cabinets forward to achieve a flush fit.
686 mm
679 mm
19 mm PANEL
610 mm
TO BACK
OF UNIT
657 mm
APPLIANCE
DOOR WIDTH
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
9 1 4 m m
W I D E M O D E L S
Panel width dimensions for installation of a 914 mm wide tall unit.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
3 mm* min
REVEAL
914 mm
908 mm
19 mm
PANEL
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
610 mm
TO BACK
OF UNIT
886 mm
APPLIANCE
DOOR WIDTH
635 mm
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
40
As the reveal between cabinets and the
Integrated unit decreases, the potential exists for severe finger pinching or crushing if a hand or fingers are placed in the opening when the door is closing.
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
681 mm
19 mm
PANEL
610 mm
TO BACK
OF UNIT
DOOR
1372 mm
681 mm
3 mm* min
REVEAL
19 mm
PANEL
When 19 mm or thicker panels are used and a reveal less than 6 mm is maintained, the door panels may cause damage to the
Sub-Zero unit when the door is open at the maximum 105˚ stop. You should use the built-in 90˚ stop to prevent damage.
DOOR
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
6 8 6 m m
W I D E M O D E L S
Panel width dimensions for installation of two 686 mm wide tall units side by side.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
P A N E L
R E Q U I R E M E N T S
Door and drawer panels must be a minimum of 16 mm thick.
The door panel cannot exceed 18 kg and each drawer panel must not exceed 5 kg for 686 mm wide units. For
914 mm wide units, the door panel weight limit is 24 kg and 7 kg for each drawer panel.
SUB-ZERO
UNIT
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
3 mm* min
REVEAL
910 mm
19 mm
PANEL
635 mm
CABINETRY
OR SIDE
PANEL
610 mm
TO BACK
OF UNIT
DOOR
SUB-ZERO
UNIT
1829 mm
910 mm
3 mm* min
REVEAL
19 mm
PANEL
DOOR
SUB-ZERO
UNIT
3 mm* min
REVEAL
635 mm
CABINETRY
OR SIDE
PANEL
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
9 1 4 m m
W I D E M O D E L S
Panel width dimensions for installation of two 914 mm wide tall units side by side.
Dimensions are based on a 3 mm reveal. A reveal of up to 6 mm is possible, but panel dimensions need to be adjusted accordingly.
41
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
I N S T A L L A T I O N O P T I O N S
The illustrations show some typical installations and their dimension considerations. The depth dimension in the illustrations may vary depending on cabinet styles, treatment of countertops or other design options.
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 635 mm. Refer to the illustrations.
NOTE: In the Installation Options illustrations, the first width dimension shown is for 686 mm wide units and the second dimension is for 914 mm wide units.
635 mm
CABINETS
686 mm
OR
914 mm
TOP VIEW
Installation without side panels
CABINETS
D U A L I N S T A L L A T I O N S
If two or more Integrated models are installed side by side where there is 51 mm or less of space between the units, a heater kit is recommended—TTDUAL for two tall units installed side by side and BBDUAL for two base units or a base unit and a tall unit installed side by side.
These optional components are available through your Sub-Zero dealer.
635 mm
686 mm OR 914 mm
MINIMUM 16 mm SIDE PANELS
Installation with side panels
CABINETS
635 mm
1372 mm OR 1829 mm
TOP VIEW
Installation of two units side by side
CABINETS
635 mm
686 mm
OR
914 mm
MINIMUM 16 mm SIDE PANELS
Installation at end of run
42
D O O R P A N E L H E I G H T
The height of the door panel can grow beyond
1153 mm and exceed the 2032 mm overall height, as long as you stay below the recommended door panel weight limit.
The top illustration shows how the panel may grow and what you need to consider doing to finish the area in back of the door panel.
IMPORTANT NOTE: The valance you use to finish the area behind the door panel must stay behind the front plane of the finished molding.
U P P E R V A L A N C E
Tall Models
The depth of each
Integrated model is
610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit.
This will require a minimum rough opening depth of
635 mm.
3 mm
T O E K I C K C L E A R A N C E
The toe kick clearance can vary with the height of the lower drawer panel; the maximum panel height is 424 mm.
IMPORTANT NOTE: You must keep a minimum space of 102 mm clear below the bottom edge of the lower drawer panel so the unit can be properly vented. In addition, any decorative base molding must be removable for possible servicing and cleaning of the condenser.
The bottom illustration shows the area below the lower drawer where the operating mechanical equipment of the Integrated unit is housed.
38 mm
635 mm TO WALL
DECORATIVE VALANCE
CANNOT EXTEND BEYOND
THE FRONT OF THIS PLANE
DECORATIVE VALANCE
P A N E L
R E Q U I R E M E N T S
Door and drawer panels must be a minimum of 16 mm thick.
The door panel cannot exceed 18 kg and each drawer panel must not exceed 5 kg for 686 mm wide units. For
914 mm wide units, the door panel weight limit is 24 kg and 7 kg for each drawer panel.
REMOVABLE MOLDING
BY SUB-ZERO
2032
mm*
TO
FLOOR
1153 mm
TO
BOTTOM
OF
DOOR
PANEL
TOP HINGE
* FINISHED HEIGHT OF 2032 mm IS TO TOP OF SUB-ZERO MOLDING
K I C K P L A T E A R E A
Base and Tall Models
268 mm
PANEL
424 mm
PANEL
254 mm
OPTIONAL
13 mm
246 mm
102 mm
67 mm
TO
102 mm
635 mm
TO WALL
BASE MOLDING MUST
BE REMOVABLE
FLOOR
43
D O O R C L O S E D
Full-scale (top view)
F R A M E D C A B I N E T R Y
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit.
1 0 5 ˚ M A X I M U M
D O O R O P E N I N G
1/4 scale (top view)
SUB-ZERO
DOOR
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
3 mm min.
REVEAL
19 mm
MOUNTING BRACKET SCREW
PANEL
657 mm
DOOR WIDTH FOR 686 mm MODELS
886 mm
DOOR WIDTH FOR 914 mm MODELS
SUB-ZERO DOOR
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
FLUSH
FURNITURE
FINISH
44
*If the panel is thicker than 19 mm, it is recommended that you utilize the built-in
90˚ door stop to prevent damage to the panel and face frame.
F R A M E L E S S C A B I N E T R Y
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit.
D O O R C L O S E D
Full-scale (top view)
3 mm min.
REVEAL
SUB-ZERO DOOR
19 mm DOOR PANEL
COUNTERTOP SIDE PANEL
610 mm
TO
WALL
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
MOUNTING BRACKET SCREW
19 mm PANEL
657 mm
DOOR WIDTH FOR 686 mm MODELS
886 mm
DOOR WIDTH FOR 914 mm MODELS
SUB-ZERO DOOR
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
1 0 5 ˚ M A X I M U M
D O O R O P E N I N G
1/4 scale (top view)
Adjacent side panel and countertop application.
*If the panel is thicker than 19 mm, it is recommended that you utilize the built-in
90˚ door stop to prevent damage to the panel and face frame.
45
46
U N D E R C O U N T E R
864 mm
606 mm
868 mm
616 mm
M O D E L I 4 2 4
Built-In
M O D E L I 4 2 4 F S
Free-Standing
A L L W I N E S T O R A G E
686 mm
762 mm
2032 mm
M O D E L I 4 2 7
Integrated
W I N E S T O R A G E
2032 mm
686 mm
M O D E L I 4 2 7 R
Integrated
2134 mm
M O D E L I 4 3 0
Built-In
| R E F R I G E R A T O R
With the installation of a harness kit, Wine Storage models are
Star-K compliant to meet strict religious regulations in conjunction with specific instructions found on www.star-k.org. For details about the harness kit, contact your
Sub-Zero dealer.
W I N E S T O R A G E
Sub-Zero‘s innovative addition to its complete line of residential refrigeration is wine storage equipment—the ultimate in beauty, engineering, and attention to detail. From the exterior and the smooth lines of the free-standing Model I424FS classic stainless steel to the ability to use wood on the Built-In and Integrated models, each unit is beautiful.
With the exception of the free-standing Model
I424FS, each model will have the capability of having wood panels applied to the doors. With the Model I427R, you can also apply the wood to the drawers.
The free-standing Model I424FS does not require any panels or surrounding cabinetry; it comes with classic stainless steel exterior.
All models will be shipped with glass doors as standard equipment. The glass doors allow one to see the wine that is being stored.
Stainless steel models will be shipped with tubular stainless steel handles, while the overlay models will come with no handle hardware.
Accessory overlay handles are available. Optional stainless steel panels and handles for Models
I427 and I427R are offered in the classic stainless steel finish and are ordered and shipped as sales accessories.
Standard grille assemblies for the Model I430 will be provided in 25 mm increments from 254 mm to 381 mm. The standard height will be 279 mm. The overlay model will have the panel grille, which accepts decorative panel inserts.
For information regarding specific Wine Storage models, refer to the illustrations in this section.
The illustrations represent the full line of
Wine Storage models. The Model I424FS free-standing unit comes with a classic stainless steel exterior.
Comprehensive installation instructions are shipped with each model. Refer to those instructions in preparing and installing all
Sub-Zero products. The instructions can also be found on our website, subzero.com.
F E A T U R E S A N D O P T I O N S
When looking for wine storage, you no longer have to think only about an undercounter application. Sub-Zero offers you complete flexibility from the perspective of design applications and storage capabilities.
Model I424 comes in the overlay and stainless steel door panel configurations. Model I424FS
(free-standing) is identical to the Model I424 but with classic stainless steel exterior and is designed to be attractive in a stand-alone setting.
Models I427 and I427R are offered as integrated or stainless steel. Optional classic stainless steel panels and handles are offered at the 2032 mm and 2134 mm height. Stainless steel panels are available as sales accessories.
Model I430 comes in overlay and stainless steel.
Stainless steel Model I430 comes with a standard 279 mm heavy-duty grille, 25 mm diameter stainless steel handles and a stainless steel kickplate.
Built-In Look. Sub-Zero offers you a host of design alternatives to choose from when selecting the look you want. Wood or stainless steel, overlay or integrated.
Dual Zone System. All Wine Storage models allow you to have precise temperature control within one degree of your pre-set temperature in each of the two wine compartments.
Dual Refrigeration System. In a similar fashion to our Built-In, each Wine Storage model has dual refrigeration so your client will have specific, individual temperature control of the two wine compartments.
Electronic Controls. Microprocessor offers touch pad controls that are easy to understand and that set the temperatures accurately.
Display Shelf. This beautiful shelf offers your clients the opportunity to display those prize bottles or magnums of wine in their collection. It is illuminated with discreet lighting mounted in the control panel. (Not available with Models
I424 and I424FS.)
Storage Shelves. The sturdy, rustproof wire shelves can easily accommodate standard 750 ml bottles, half bottles, as well as magnums. All the shelves are finished off with a natural cherry wood facing. In addition, all shelves will enable you to be sure the wine is stored properly and that the corks are in contact with the bottles‘ contents.
Roller Assembly. All shelves have a roller assembly, which enables you to have a threequarter extension for easy access to all bottles of stored wine.
Service Alert. An indicator light will let you know if service may be necessary.
Home Alarm. Wiring connections give you the option of hooking the Wine Storage unit up to your home security system.
Discreet Lighting. Our soft low-wattage lighting is independent of door opening.
Correct Temperature. The range of each temperature zone is 3˚C to 18˚C, and your set temperature is digitally displayed in the control panel.
Humidity. Proper humidity is maintained throughout the entire unit.
UV Protection. The tinted glass minimizes the amount of ultraviolet light entering the unit.
Lock. A lock will be offered as an option for all
Wine Storage models. The lock is offered as a sales accessory and should be ordered through your Sub-Zero dealer. Special planning is necessary when ordering locks for Models I427 and
I427R; see page 57 for details.
Tight Seal. Magnetic gaskets around the doors give extra-tight seals.
Kickplate. The solid, adjustable kickplate gives a true built-in look and conforms to American
Institute of Architects standards.
Front Venting. All Sub-Zero Wine Storage models are designed for mechanical system airflow at the front of the appliance. Decorative panels must not cover louvered surfaces or prevent removal of louvered components.
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
47
M O D E L I 4 2 4
U N D E R C O U N T E R
B U I L T - I N
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I424/O
I424/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Wine Storage Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt (glass)
Shipping Wt (glass/S)
606 mm
864 mm
610 mm
46 bottles*
870 mm
645 mm
LH or RH
86 kg
88 kg
F E A T U R E S
2 Temperature Zones
8 (750 ml) Bottles per Standard Shelf
2 Top Zone Shelves (16 bottles*)
3 Bottom Zone Shelves (24 bottles*)
1 Fixed Bottle Holder (6 bottles*)
Full-View Glass Door
M O D E L I 4 2 4 F S
U N D E R C O U N T E R
F R E E - S T A N D I N G
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Wine Storage Capacity
Door Swing Clearance
Specify Door Swing
Shipping Wt
616 mm
868 mm
625 mm
46 bottles*
645 mm
LH or RH
100 kg
F E A T U R E S
2 Temperature Zones
8 (750 ml) Bottles per Standard Shelf
2 Top Zone Shelves (16 bottles*)
3 Bottom Zone Shelves (24 bottles*)
1 Fixed Bottle Holder (6 bottles*)
Full-View Glass Door
Classic Stainless Steel Exterior and Door Frame
M O D E L I 4 2 7
A L L W I N E S T O R A G E
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Wine Storage Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt
686 mm
2032 mm
610 mm
132 bottles*
2019 mm
648 mm
LH or RH
179 kg
F E A T U R E S
2 Temperature Zones
9 (750 ml) Bottles per Standard Shelf
5 Top Zone Shelves (45 bottles*)
9 Bottom Zone Shelves (81 bottles*)
1 Display Shelf (6 bottles*)
Full-View Glass Door
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handle)**
M O D E L I 4 2 4
48
M O D E L I 4 2 4 F S M O D E L I 4 2 7
M O D E L I 4 3 0
A L L W I N E S T O R A G E
M O D E L I 4 2 7 R
W I N E S T O R A G E
|
R E F R I G E R A T O R
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
I430/O
I430/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Wine Storage Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Wt
Shipping Wt (glass /S)
762 mm
2134 mm
610 mm
147 bottles*
2108 mm
765 mm
LH or RH
197 kg
202 kg
F E A T U R E S
2 Temperature Zones
10 (750 ml) Bottles per Standard Shelf
5 Top Zone Shelves (50 bottles*)
9 Bottom Zone Shelves (90 bottles*)
1 Display Shelf (7 bottles*)
Full-View Glass Door
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Wine Storage Capacity
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Drawer Clearance
Shipping Wt
686 mm
2032 mm
610 mm
78 bottles*
150 L
2019 mm
648 mm
LH or RH
495 mm
186 kg
F E A T U R E S
3 Temperature Zones
2 Refrigerated Drawers
9 (750 ml) Bottles per Standard Shelf
6 Top Zone Shelves (54 bottles*)
2 Bottom Zone Shelves (18 bottles*)
1 Display Shelf (6 bottles*)
Full-View Glass Door
P A N E L O P T I O N S
Integrated
Classic stainless steel finish
(includes handles)**
*750 ml bottles.
**Optional stainless steel panels and handles are ordered and shipped as sales accessories.
M O D E L I 4 3 0 M O D E L I 4 2 7 R
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Classic stainless steel front panels (Models I427 and I427R)*
Tubular handles in classic stainless steel
Side and grille panels
(Model I430)*
Panel, louvered or stainless steel grilles in varied heights
(Model I430)*
Dual installation heater kit
(Models I427 and I427R)*
*Accessory is available only for models listed.
49
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
P L A N N I N G I N F O R M A T I O N
Review the Overall Dimensions and Installation
Specifications illustrations for your Wine Storage model on the following pages. These specifications cover all the details you need to know about space allocation and placement of electrical, whether the models are overlay, stainless steel or integrated.
All Wine Storage models must be installed so that the door can open a minimum of 90˚ or you will have problems pulling the wine shelves out.
Refer to the door clearance and door swing information.
For corner installations, you need allow for a minimum 76 mm filler so the door can open to
90˚. If you are using larger handle hardware, you will also need to take that into account.
For a maximum 90˚ door opening, use the door stop built into the hinge system of Model I427.
An optional 90˚ door stop kit for Model I430 is available from your Sub-Zero dealer.
If you will be connecting the unit to a home security system, you must allow a minimum of
914 mm of the system‘s wiring to be routed in the electrical area designated for your model.
IMPORTANT NOTE: The anti-tip bracket must be installed to prevent the unit from tipping forward.
E L E C T R I C A L R E Q U I R E M E N T S
International models from the factory designed without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device.
International models using a factory installed transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit. These models will come equipped with
Schuko power cords. The power cord may need to be replaced depending on local and national codes. The USA power cord that is supplied with the product must be disconnected with the appropriate transformer output to be connected in its place.
IMPORTANT NOTE: The electrical outlet must be grounded. The outlet must be flush with the back wall. Refer to the Installation Specifications illustration for your model for exact placement.
IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
D U A L I N S T A L L A T I O N S
If you are installing a Wine Storage unit next to an existing Sub-Zero unit, you may have to allow for a filler strip.
If you are installing a Model I427 or I427R Wine
Storage unit next to an existing Integrated
Sub-Zero unit, with 51 mm or less between the units, an optional heater kit (BBDUAL or
TTDUAL) will need to be installed to prevent moisture from forming between the units. This optional kit is available through your Sub-Zero dealer.
50
O V E R A L L D I M E N S I O N S
Undercounter Wine Storage
273 mm
CENTERED
VERTICALLY
606 mm
597 mm DOOR FRAME
864
mm*
767 mm
DOOR
FRAME
587 mm
(CABINET DIMENSION)
102 mm
FRONT VIEW
* 13 mm +
M O D E L I 4 2 4
Built-In
Width 606 mm
Height 864 mm
Depth 610 mm
Note the location of pre-drilled holes for optional handle hardware.
SIDE VIEW
616 mm 625 mm
(CABINET DIMENSION)
868
mm*
FRONT VIEW
* 13 mm +
M O D E L I 4 2 4 F S
Free-Standing
Width 616 mm
Height 868 mm
Depth 625 mm
102 mm
TOE KICK
SIDE VIEW
U N D E R C O U N T E R
Model I424
Built-In
Model I424FS
Free-Standing
I N S T A L L A T I O N S P E C I F I C A T I O N S
Undercounter Models
Model I424
A) Rough Opening Width 610 mm
B) Rough Opening Height 876 mm
C) Min Door Clearance 644 mm
D) Min Clearance at 90˚ 660 mm
Model I424FS*
C) Min Door Clearance
D) Min Clearance at 90˚
644 mm
660 mm
*Free-standing Model I424FS requires no surrounding cabinetry.
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
64 mm
610 mm
ROUGH
OPENING
DEPTH
TOP VIEW
A
ROUGH OPENING
WIDTH
LOCATE ELECTRICAL
WITHIN SHADED AREA
114 mm
394 mm
E
FRONT VIEW
B
ROUGH
OPENING
HEIGHT TO
FINISHED
FLOORING
90˚
C
D
51
O V E R A L L D I M E N S I O N S
All Wine Storage – Model I427
I N T E G R A T E D
Model I427
All Wine Storage
Model I427R
Wine Storage |
Refrigerator
20 mm
O V E R A L L
D I M E N S I O N S
Model I427 | I427R
Width 686 mm
Height 2032 mm
Depth 610 mm
273 mm
CENTERED
VERTICALLY
686 mm
664 mm
DOOR FRAME
356 mm
2032 mm
1997
mm*
1789 mm
DOOR
FRAME
WITH
HINGES
Note the location of pre-drilled holes for optional handle hardware.
610 mm
(UNIT DIMENSION)
* 13 mm +
FRONT VIEW
227 mm
102 mm
SIDE VIEW
Wine Storage | Refrigerator – Model I427R
686 mm
664 mm DOOR FRAME
356 mm
610 mm
(UNIT DIMENSION)
20 mm
273 mm
CENTERED
VERTICALLY
9 mm
1139 mm
DOOR
FRAME
WITH
HINGES
2032 mm
1997
mm*
13 mm
337 mm
650 mm
DRAWER FRONT
260 mm
517 mm
* 13 mm +
FRONT VIEW
877
mm*
248 mm
102 mm
SIDE VIEW
I N S T A L L A T I O N S P E C I F I C A T I O N S
Models I427 | I427R
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
IMPORTANT NOTE: The depth of Models
I427 and I427R is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of
635 mm.
635 mm
ROUGH
OPENING
DEPTH
TOP VIEW
90˚
711 mm
DOOR CLEARANCE
648 mm
105˚
MAXIMUM
DOOR SWING
889 mm
DOOR CLEARANCE
606 mm
2032 mm
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING
2019 mm
MIN HEIGHT
REQUIRED
686 mm
ROUGH OPENING WIDTH
648 mm
64 mm
LOCATE ELECTRICAL
WITHIN SHADED AREA
114 mm
394 mm
E
FRONT VIEW
ANTI-TIP BRACKET
52
O V E R A L L D I M E N S I O N S
All Wine Storage – Model I430
762 mm
719 mm DOOR FRAME
606 mm
273 mm
2134 mm
1724 mm
DOOR
FRAME
A L L W I N E
S T O R A G E
Model I430
Built-In
O V E R A L L
D I M E N S I O N S
Model I430
Width 762 mm
Height 2134 mm
Depth 610 mm
Note the location of pre-drilled holes for optional handle hardware.
FRONT VIEW
105 mm
TOE
KICK
*
13 mm ADJUSTMENT IN LEVELING LEGS
SIDE VIEW
I N S T A L L A T I O N S P E C I F I C A T I O N S
All Wine Storage – Model I430
Dimensions are for finished rough openings.
Door swing clearances are based on stainless steel door and handle dimensions.
90˚
838 mm
DOOR CLEARANCE
765 mm
610 mm
ROUGH
OPENING
DEPTH
TOP VIEW
606 mm
BEHIND
FRAME
ANTI-TIP BLOCK
178 mm
E
LOCATE ELECTRICAL
WITHIN SHADED AREA
152 mm
130˚
MAXIMUM
DOOR SWING
1270 mm
DOOR CLEARANCE
765 mm
2127 mm
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
2108 mm
MIN HEIGHT
REQUIRED
(LEVELERS IN)
749 mm
ROUGH OPENING WIDTH
1918 mm
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
FRONT VIEW
53
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
D O O R P A N E L S
Unless you are installing a stainless steel model, you will need to provide a frame for the glass door. If you order a stainless steel unit, Models
I424, I424FS and I430 will be shipped with their panels and hardware installed and you will merely install the Sub-Zero. However, for Models
I427 and I427R, you will have to have the stainless steel panels and handles installed.
M O D E L I 4 2 4 F S – F R E E - S T A N D I N G
The free-standing Model I424FS does not require any panels or surrounding cabinetry. It has a beautiful classic stainless steel exterior, door frame and handle. Refer to the Overall Dimensions illustration for the Model I424FS.
54
O V E R L A Y P A N E L S – M O D E L I 4 2 4
The overlay panel applied to Model I424 should not be confused with the Built-In overlay panel application. The overlay panel will consist of only a frame and would be either the 16 mm or 19 mm thick panel you may be using. It is affixed directly to the door itself with screws through a series of pre-drilled holes in the perimeter of the door itself. You do not need any backer or spacer panel.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Model I424 to give you a better idea of the exact space our unit needs and how the panel fits in relationship with the unit.
The glass door opening of the standard Model
I424 is designed to be exposed to room air circulation. Decorative overlays on the glass should be kept to a minimum. Also, rails and stiles can be increased in size but should not exceed cabinet manufacturers‘ standard width. They cannot exceed overall door panel dimensions specified, as they would interfere with the operation of the door. The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frames must be finished to match the front surface.
The Overall Dimensions illustrations show the location of predrilled holes for optional handle hardware. Refer to page 60 for specifics about installing handles on this overlay application.
IMPORTANT NOTE: When planning to install the
Model I424 next to adjoining cabinetry, you must make provisions to allow the door to open to a maximum of 145˚ and not interfere with the door panel. Refer to the full-scale illustration at the end of this section.
I N S T A L L A T I O N
To install overlay panels, see the detailed procedures outlined in the
Sub-Zero Wine
Storage Installation
Guide.
C A B I N E T R Y D I M E N S I O N S
Model I424
606 mm
603 mm DOOR PANEL
606 mm**
(CABINET DIMENSION)
877 mm*
764 mm
DOOR
PANEL
CENTERED
VERTICALLY
O V E R L A Y P A N E L S P E C I F I C A T I O N S
Model I424
Door Panel Width
Door Panel Height
603 mm
764 mm
Min Width of Rails and Stiles 57 mm
Door Frame Panel Weight Limit 5 kg
Min Panel Thickness 16 mm
FRONT VIEW
102 mm
TOE
KICK SIDE VIEW
* 13 mm ADJUSTMENT IN LEVELING LEGS
** MODEL I424/S (STAINLESS STEEL WRAPPED DOOR) FINISHES OFF AT 606 mm DEEP
55
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
I N T E G R A T E D P A N E L S –
M O D E L S I 4 2 7 | I 4 2 7 R
The integrated frame panels for glass doors for these models will follow some of the identical planning processes used with the Integrated line.
The installation of the door panels is completely different, however. Rather than using the mounting hardware we used with the Integrated line, door panels for both Models I427 and I427R will be applied with screws applied through our door.
The drawer panels for the Model I427R will be applied using the Integrated technique of mounting brackets.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Models I427 and
I427R to give you a better idea of the exact space our unit needs and how the panel fits in relationship with the unit.
IMPORTANT NOTE: The depth of Models I427 and I427R is 610 mm from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into the drywall or bring the cabinets forward. Refer to pages 37–43 of the Integrated section.
IMPORTANT NOTE: The glass door opening of the standard Models I427 and I427R is designed to be exposed to room air circulation. Decorative overlays on the glass should be kept to a minimum. While the cabinet front stiles are a minimum of 57 mm for both Models I427 and
I427R, the top and bottom rails are different.
Rails and stiles can be increased in size but should not exceed cabinet manufacturers‘ standard width. They cannot exceed overall door panel dimensions specified, as they would interfere with the operation of the door. The back sides of rails and stiles that will be visible through the glass door will need to be finished.
Also, the inside edges of the frames must be finished to match the front surface.
IMPORTANT NOTE: The inside edges of the rough opening will need to be finished as they will be exposed when the doors are open.
C A B I N E T R Y D I M E N S I O N S
Model I427
686 mm
FINISHED OPENING
679 mm DOOR PANEL
610 mm
(UNIT DIMENSION)
I N T E G R A T E D P A N E L S P E C I F I C A T I O N S
Model I427
Door Panel Width
Door Panel Height
Min Width of Top Rail
Min Width of Bottom Rail
Min Width of Stiles
Door Frame Panel Weight Limit
Min Panel Thickness
679 mm
1927 mm
95 mm
203 mm
57 mm
9 kg
16 mm
1927 mm
DOOR
PANEL
2032 mm
FINISHED
OPENING
2029 mm
TRIMMED
DOOR
102 mm
TOE KICK
102 mm
FRONT VIEW TOE KICK SIDE VIEW
NOTE: 13 mm ADJUSTMENT IN LEVELING LEGS
56
IMPORTANT NOTE: The dimensions of these panels and stiles are assuming the models finish off at 2032 mm in height overall and have a 102 mm toe kick for the Model I427. If you finish off at 2134 mm, for instance, you must add 102 mm additional to the overall height of the panel and remember to add 102 mm to the top rail.
Likewise, if you allow for a 152 mm toe kick for the Model I427, you must subtract 51 mm from the bottom rail.
Door panels for Models I427 and I427R can grow beyond the 2032 mm height to accommodate any size door as long as you stay below door panel weight limit of 9 kg. Refer to the specifications under Door Panel Height on page
43 of the Integrated section.
IMPORTANT NOTE: The toe kick area on the
Model I427 cannot be larger than 152 mm, and no larger than 229 mm for the 427R. The toe kick area for either model cannot be less than
102 mm.
Please note in the Overall Dimensions illustrations the location of pre-drilled holes for optional handle hardware. Refer to page 60 for specifics about installing handle hardware on this overlay application.
IMPORTANT NOTE: If you are installing
Sub-Zero‘s optional lock kit on a Model I427 or
I427R, you may have to order door panels that exceed the 2032 mm finished height. Consult the lock kit installation instructions and see if your panels will allow for an adequate installation.
IMPORTANT NOTE: In the panel specifications for Model I427R, the bottom drawer panel height is based on a 102 mm toe kick. If you want to show a 152 mm toe kick, you must subtract 51 mm from the bottom drawer panel height.
I N S T A L L A T I O N
To install integrated panels, see the detailed procedures outlined in the
Sub-Zero Wine
Storage Installation
Guide.
C A B I N E T R Y D I M E N S I O N S
Model I427R
686 mm
FINISHED OPENING
679 mm
DOOR PANEL
610 mm
(UNIT DIMENSION)
1153 mm
2032 mm
FINISHED
OPENING
3 mm
3 mm
345 mm
679 mm
DRAWER PANEL
2029 mm
TRIMMED
DOOR
877
mm*
424 mm
102 mm
TOE KICK
102 mm
FRONT VIEW TOE KICK
* 13 mm ADJUSTMENT IN LEVELING LEGS
SIDE VIEW
I N T E G R A T E D P A N E L S P E C I F I C A T I O N S
Model I427R
Door Panel Width
Door Panel Height
Min Width of Top Rail
Min Width of Bottom Rail
Min Width of Stiles
Door Frame Panel Weight Limit
Top Drawer Panel Width
Top Drawer Panel Height
Bottom Drawer Panel Width
Bottom Drawer Panel Height
Drawer Panel Weight Limit
Min Panel Thickness
679 mm
1153 mm
95 mm
76 mm
57 mm
9 kg
679 mm
345 mm
679 mm
424 mm
5 kg each
16 mm
57
O V E R L A Y P A N E L S – M O D E L I 4 3 0
Your overlay model will be shipped without handle hardware and with an 279 mm overlay panel grille as standard equipment. You will need to order a panel for the grille and hardware to complement your surrounding cabinetry.
While the overlay panel design offers you a more seamless appearance, you need to be aware of adjacent cabinets and/or countertops when the door is opened. Refer to the full-scale illustrations at the end of the Built-In section.
To achieve the overlay look, you need three different panels—the decorative overlay panel, a
3 mm spacer panel and a 6 mm backer panel.
Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels. Refer to the Overlay Panel Specifications for complete details on the overlay sizing. In addition, illustrations 2 and 3 will give you a better idea of the panel construction and how it interacts with our frame.
The glass door opening of the standard Model
I430 is designed to be exposed to room air circulation. Decorative overlays on the glass should be kept to a minimum. Also, rails and stiles can be increased in size but should not exceed cabinet manufacturers‘ standard width. They cannot exceed overall door panel dimensions specified, as they would interfere with the operation of the door.
58
Trim Reveal 6 mm min
Rout to 6 mm thickness
57 mm
Rail / Stile
Door
Frame
Illus. 1
16 mm
Glass
57 mm Rail / Stile
3 mm Spacer Panel
3 mm
Overlay Panel
6 mm Backer Panel
8 mm min
Door Frame Glass
4 mm
2 mm
Door / Grille
Trim
Illus. 2
Overlay Panel
Spacer Panel
16 mm min
3 mm
6 mm
Backer
Panel
Illus. 3
The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frames must be finished to match the front surface.
As with the Sub-Zero Built-In models, you have the flexibility of ordering grilles in a variety of heights for the overlay application. Overlay grille panel dimensions for the overlay Model I430, standard 279 mm grille, are listed below. Refer to page 23 for optional grille height dimensions.
The width of the overlay grille, spacer and backer panel will be the same regardless of the height.
In addition, side panel information for a Model
I430 is available on page 21 of the Built-In section. Refer to illustration 11 on page 21 for placement of toe kick and grille area cut-outs.
I N S T A L L A T I O N
To install overlay panels, see the detailed procedures outlined in the
Sub-Zero Wine
Storage Installation
Guide.
C A B I N E T R Y D I M E N S I O N S
Model I430
762 mm
722 mm DOOR FRAME
2134 mm
1727 mm
DOOR
PANEL
CENTERED
VERTICALLY
FRONT VIEW
103 mm TOE
KICK SIDE VIEW
NOTE: 13 mm ADJUSTMENT IN LEVELING LEGS
O V E R L A Y P A N E L S P E C I F I C A T I O N S
Model I430 – Overlay (O)
Overlay Door Panel Width
Overlay Door Panel Height
Spacer Panel Width
Spacer Panel Height
Backer Panel Width
722 mm
1727 mm
699 mm
1073 mm
714 mm
Backer Panel Height
Min Width of Rails and Stiles
Door Frame Panel Weight Limit
Min Panel Thickness
1719 mm
57 mm
11 kg
16 mm
G R I L L E P A N E L S P E C I F I C A T I O N S
Model I430 – Overlay (O)
Overlay Grille Panel Width
Overlay Grille Panel Height*
Spacer Panel Width
Spacer Panel Height*
Backer Panel Width
Backer Panel Height*
Grille Panel Weight Limit
Min Panel Thickness
722 mm
260 mm
699 mm
236 mm
714 mm
252 mm
7 kg
16 mm
*Grille panel dimensions are for standard 279 mm grille. Refer to page 22 for optional grille heights.
59
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
H A R D W A R E C O N S I D E R A T I O N S
With Model I424 (overlay), Models I427 and
I427R (integrated) and Model I430 (overlay), you must supply your own handle hardware. It is recommended you use our optional handles and use the pre-drilled holes supplied to locate the handles within the frame of our unit. The metal frame on the door has numerous mounting holes on each side to accommodate Sub-Zero accessory handles. This will allow you to provide the best possible handle alignment and not take away from the strength of the stile in this area after the unit is used a number of times. We recommend using a pull handle and not a pull knob.
If you elect to place different hardware on these units, we encourage you to fasten the hardware by passing through our door and attaching the hardware through the Sub-Zero door‘s frame.
Optional stainless steel handles are available in a variety of diameters and lengths, as are handles to match the style of Wolf ovens. Contact your
Sub-Zero dealer for specifics.
W I N E S H E L F W O O D F A C I N G
Sub-Zero has provided a natural cherry wood facing to its wine storage shelves in each model.
You can also replace these strips with wood more complementary to your design and surrounding cabinetry.
The Wine Shelf Wood Facing illustration on the following page can be used as a full-scale template. You must follow the layout of this format to accommodate the shelves properly. To remove the cherry strips, take the shelves out and remove the screws. Reverse the procedure to affix the new wood.
If you choose to stain or seal the wood facing, be aware that some of these substances are hazardous and will damage stored wine.
When planning for hardware, refer to the
Door Frame Profile full-scale illustration on the following page to give you a better understanding of the unit‘s frame and positioning of the glass for the door. You must not drill through this glass.
60
D O O R F R A M E P R O F I L E
Glass
Cabinet Door
Profile
A
57 mm Rail / Stile
A
This full-scale illustration is typical of the
Model I424 door frame profile; details of the other Wine Storage door frames will vary slightly.
W I N E S H E L F W O O D F A C I N G
D O O R F R A M E H A N D L E O F F S E T
Wine Storage Models
Dimension A
Model I424
Model I427
Model I427R
Model I430
25 mm
22 mm
22 mm
24 mm
IMPORTANT NOTE: Rails and stiles must be a minimum of 57 mm wide (except for the rails of Models I427 and I427R, which must be wide enough to cover the door hinges).
The back sides of rails and stiles that will be visible through the glass door will need to be finished.
F U L L - S C A L E
T E M P L A T E S
The full-scale illustrations on the following pages enable you to understand some of the unique situations you may face as you plan for the installation of the Wine
Storage units. Use these illustrations as templates.
3 mm
38 mm
21 mm
2 mm
16 mm Maximum Thickness
A
(WIDTH)
FRONT VIEW
This full-scale illustration provides the dimensions you will need should you choose to replace the natural cherry wood facing of each wine shelf with wood more complementary to your design and surrounding cabinetry.
9 mm
14 mm
SIDE VIEW
W I N E S H E L F W O O D F A C I N G
Wine Storage Models
Dimension A
Model I424
Model I424FS
Model I427
Model I427R
Model I430
495 mm
495 mm
532 mm
532 mm
624 mm
61
62
M O D E L I 4 2 4 – D O O R C L O S E D A N D 1 4 5 ˚ M A X O P E N I N G
610 mm
CABINETRY
OPENING
587 mm
TO BACK OF
APPLIANCE
SUB-ZERO DOOR
19 mm
DOOR PANEL
600 mm
DOOR PANEL
WIDTH
The full-scale illustration shows what considerations you need to make for the installation of Model I424 and how the maximum door opening may interact with adjacent cabinets and countertops.
145 ˚ *
13 mm
*
MODEL I424 MUST
EXTEND A MINIMUM
6 mm BEYOND THE
FRONT SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
3 mm
6 mm*
SUB-ZERO
DOOR
DOOR
PANEL
N E W U N D E R C O U N T E R R E F R I G E R A T I O N
Available in 2007
Aside from the full-size models that Sub-Zero offers in its Built-In and Integrated lines of refrigeration and its Wine Storage equipment, we round out our product line-up with a new line of
Undercounter refrigeration available in 2007.
Our new Undercounter line consists of an all refrigerator model, an all refrigerator beverage center, a refrigerator / freezer combination model and an all refrigerator model designed for outdoor applications. The existing ice maker
Model 315IP will continue to be offered.
The Undercounter models accept a decorative door panel for an overlay or stainless steel application and can be built in to fit flush with virtually any base cabinet style. The outdoor
Model UC-24RO is available in classic stainless steel only and comes with door panel and handle in place. Model UC-24RO must also be built-in into cabinetry and is not designed to be a free-standing unit.
A classic stainless steel door panel with handle is available as a sales accessory for Models
UC-24R and UC-24C. Contact your Sub-Zero dealer for information on accessory panels and handles. Model UC-24B must be ordered as overlay (UC24-B/O) or stainless steel (UC-24B/S).
Optional stainless steel panels and handles for
Model 315IP are offered in classic stainless steel.
NEW
A L L R E F R I G E R A T O R
606 mm
864 mm
M O D E L U C - 2 4 R
All Refrigerator
NEW
B E V E R A G E C E N T E R
606 mm
864 mm
M O D E L U C - 2 4 B
All Refrigerator
NEW
C O M B I N A T I O N
606 mm
864 mm
M O D E L U C - 2 4 C
Combination
Refrigerator / Freezer
NEW
O U T D O O R M O D E L
606 mm
864 mm
Comprehensive installation instructions are shipped with each model. Refer to those instructions in preparing and installing all
Sub-Zero products. The instructions can also be found on our website, subzero.com.
M O D E L U C - 2 4 R O
All Refrigerator
I C E M A K E R
386 mm
854 mm
M O D E L 3 1 5 I P
Ice Maker
63
M O D E L U C - 2 4 R
A L L R E F R I G E R A T O R
NEW
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Weight
606 mm
864 mm
610 mm
161 L
870 mm
645 mm
LH or RH
59 kg
F E A T U R E S
2 Adjustable Glass Shelves
1 Utility Bin
2 Door Shelves
M O D E L U C - 2 4 B
B E V E R A G E C E N T E R
NEW
M O D E L O P T I O N S
Overlay Design
Classic Stainless Steel
UC-24B/O
UC-24B/S
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Wine Storage Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Weight (O)
Shipping Weight (S)
606 mm
864 mm
610 mm
161 L
16 bottles*
870 mm
645 mm
LH or RH
59 kg
61 kg
F E A T U R E S
2 Wine Storage Shelves
1 Adjustable Glass Shelf
1 Utility Bin
Full-View Glass Door
M O D E L U C - 2 4 C NEW
C O M B I N A T I O N
R E F R I G E R A T O R
|
F R E E Z E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Wine Storage Capacity
Freezer Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Weight
606 mm
864 mm
610 mm
102 L
8 bottles*
31 L
870 mm
645 mm
LH or RH
59 kg
F E A T U R E S
1 Wine Storage Shelf
1 Adjustable Glass Shelf
1 Door Shelf
Automatic Defrost
Automatic Ice Maker
M O D E L U C - 2 4 R
*750 ml bottles
Optional stainless steel panels and handles are ordered and shipped as sales accessories for Models UC-24R,
UC-24C and 315IP.
M O D E L U C - 2 4 B
64
M O D E L U C - 2 4 C
M O D E L U C - 2 4 R O
A L L R E F R I G E R A T O R
O U T D O O R M O D E L
NEW M O D E L 3 1 5 I P
I C E M A K E R
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Refrigerator Capacity
Min Height Required
Door Swing Clearance
Specify Door Swing
Shipping Weight
606 mm
864 mm
610 mm
161 L
870 mm
645 mm
LH or RH
59 kg
F E A T U R E S
2 Adjustable Glass Shelves
1 Utility Bin
2 Door Shelves
Door Lock
Classic Stainless Steel Finish
S P E C I F I C A T I O N S
Overall Width
Overall Height
Overall Depth
Ice Storage Capacity
Min Height Required
Door Swing Clearance
Shipping Weight
386 mm
854 mm
610 mm
12 kg
857 mm
387 mm
45 kg
F E A T U R E S
Automatic Ice Maker
Automatic Defrost
Reversible Door Swing
Drain Pump
P A N E L O P T I O N S
Custom Wood Panel
Classic stainless steel finish
(includes handle)
M O D E L U C - 2 4 R O M O D E L 3 1 5 I P
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
A C C E S S O R I E S
Contact your Sub-Zero Dealer
Classic stainless steel door front panel with tubular handle
Classic stainless steel tubular handle for overlay application
UL approved door lock
65
A C C E S S O R I E S
Optional accessories are available through your
Sub-Zero dealer.
U N D E R C O U N T E R F E A T U R E S
Overlay Application. The overlay application blends seamlessly into your overall room design and complements surrounding cabinetry. You add the decorative door front panel and hardware.
Sub-Zero accessories handles are available. The overlay application is available for all Undercounter models except Model UC-24RO. Model
UC-24B must be ordered specifically as overlay
(UC24-B/O).
Stainless Steel Application. Classic stainless steel door front panel and handle is available as an accessory for Models UC-24R, UC-24C and
315IP. Model UC-24B must be ordered specifically as stainless steel (UC24-B/S). Model
UC-24RO is available as a classic stainless steel model only and comes with door panel and handle in place.
U N D E R C O U N T E R M O D E L F E A T U R E S
Electronic Controls. The electronic controls with digital readout LCD display are up front and easy to access.
Glass Shelves. The cantilevered glass shelves are adjustable, easy to clean and spill proof. The glass floor is also spill proof.
Utility Bin. All units except Model UC-24C feature a clear utility bin for storage of smaller items.
Wine Storage. Models UC-24B and UC-24C feature wine storage of 16 and 8 (750 ml) bottles, respectively. The roller-glide wine storage shelves faced with natural cherry wood have a three-quarter extension for easy access.
Glass Door—Model UC-24B. The full-view glass door and accent lighting of Model UC-24B matches the appearance of Wine Storage Model
I424.
Ice Maker. Model UC-24C refrigerator/freezer features an automatic ice maker with clear ice bucket. The ice maker provides high-quality, crescent-shaped ice that won’t stick to the side of the glass.
Two-Litre Bottle Storage. All units except Model
UC-24B feature two-litre bottle storage in the bottom door shelf.
Door Lock. A UL approved lock is standard on
Model UC-24RO and available as a sales accessory for all other models.
Sabbath Feature. The Sabbath feature will allow the lights to remain off during certain religious observances.
3 1 5 I P M O D E L F E A T U R E S
Built-in pump to allow water to drain into an adjacent sink.
Ice storage capapcity of up to 11.8 kg.
66
P L A N N I N G I N F O R M A T I O N
Refer to the Installation Specifications for information regarding area requirements, minimum door clearance, placement of electrical and plumbing (Models UC-24C and 315IP).
P L U M B I N G R E Q U I R E M E N T S
For Models UC-24C and 315IP, rough in the water supply line. Connect a 6.35 mm OD copper line to the house supply with an easily accessible shut-off valve between the supply and the unit. A minimum of 660 mm of copper tubing is required for the water line.
Do not use self-piercing valves. A saddle valve kit (4200880) is available from your Sub-Zero dealer. An in-line filter is required when water conditions have a high sediment content.
The ice maker operates on constant water pressure between 1.4 bar and 6.9 bar.
IMPORTANT NOTE: In some cases, a reverse osmosis water filter system may not be able to maintain the minimum pressure consistently.
E L E C T R I C A L R E Q U I R E M E N T S
A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance is required.
All Undercounter models are equipped with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating
3-prong grounding-type wall receptacle. Follow local codes and ordinances when installing the receptacle. Refer to the Installation Specifications illustrations.
IMPORTANT NOTE: The Model UC-24RO is designed and safe for use in outdoor applications. When installed outdoors, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. A GFCI is not recommended for use with other Undercounter models and may cause interruption of operation.
M O D E L O P T I O N S
Model UC-24R
All Refrigerator
Model UC-24B
All Refrigerator
Beverage Center
Model UC-24C
Refrigerator | Freezer with Ice Maker
Model UC-24RO
All Refrigerator
Outdoor Model
Model 315IP
Ice Maker with
Drain Pump
I N S T A L L A T I O N S P E C I F I C A T I O N S
Undercounter Models
Overall Dimensions
Overall Width
Overall Height
Overall Depth
606 mm
864 mm
610 mm
Finished Opening Dimensions
Opening Width 610 mm
Opening Height
Opening Depth
Door Swing Clearance
876 mm
610 mm
645 mm
Model 315IP
Min Door Clearance
Water Supply
387 mm
203 mm
Models without an ice maker will not require the water line connection.
For Model 315I(P), the electrical supply can be located anywhere on the back wall.
Door swing clearance based on stainless steel door panel and handle dimensions.
51 mm 394 mm
13 mm
LOCATE WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
TOP VIEW
610 mm
ROUGH OPENING
WIDTH
ANTI-TIP BRACKET
LOCATE ELECTRICAL
AND WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
394 mm
76 mm
51 mm
FRONT VIEW
610 mm
ROUGH
OPENING
DEPTH
876 mm
ROUGH
OPENING
HEIGHT
870 mm
MINIMUM
HEIGHT
REQUIRED
90˚
644 mm
660 mm
DOOR CLEARANCE
67
I N S T A L L A T I O N
Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
D R A I N P U M P – M O D E L 3 1 5 I P
This ice maker comes with a built-in drain pump.
The drain and inlet water tubes must be plumbed before connecting to the ice maker. An air gap will likely be required between the ice maker drain tube and the drain/waste receptacle.
A stand pipe with a trap below it would be acceptable for the drain/waste receptacle. Refer to the illustrations below.
IMPORTANT NOTE: Poor drainage will cause a high rate of ice melting in the bin.
D O O R P A N E L – M O D E L 3 1 5 I P
It is important to understand the differences in mounting any wood panel to the Model 315IP.
Refer to the installation instructions packaged with the unit to understand how the panel is installed. It does not require a 6 mm backer.
Door panel dimensions are 381 mm wide by
772 mm high and must be a minimum of 16 mm thick. The maximum door panel weight is 7 kg.
No handle recess is required.
68
I N S T A L L A T I O N S P E C I F I C A T I O N S
Model 315IP – Drain Pump
SHUT-OFF
VALVE
WATER
FILTER
3 mm
WATER
INLET TUBE
DRAIN
TUBE
609 mm
AIR GAP
DEVICE
387 mm
MIN.
TOP VIEW
SHUT-OFF
VALVE
AIR GAP
DEVICE
876 mm
NOMINAL
DRAIN
TUBE
857 mm
MIN.
WATER
INLET TUBE
WATER
FILTER
387 mm
MIN.
FRONT VIEW
O V E R L A Y D O O R P A N E L –
M O D E L S U C - 2 4 R A N D U C - 2 4 C
The overlay door panel design allows for a decorative panel to cover the door trim for a seamless appearance that will compliment surrounding cabinetry. You may also choose to match the handle hardware of surrounding cabinetry.
Refer to the Overlay Panel Specifications below for your specific model. Illustration 1 below applies to Models UC-24R and UC-24C. Illustration 2 applies to Model UC-24B. Outdoor Model
UC-24RO is available as a classic stainless steel model only and comes with door panel and handle in place.
O V E R L A Y D O O R P A N E L –
M O D E L U C - 2 4 B
The overlay door panel applied to the Model
UC-24B will consist of only a frame and will affix directly to the door with screws through a series of predrilled holes in the perimeter of the door.
The glass door opening of the Model UC-24B is designed to be exposed to room air circulation.
Decorative overlays on the glass should be kept to a minimum. Rails and stiles must be a minimum of 57 mm wide. They can be increased in size but should not exceed cabinet manufacturers standard width. Rails and stiles cannot exceed the overall door panel dimensions specified in the Overlay Panel Specifications, as they would interfere with the operation of the door.
The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frames must be finished to match the front surface.
I N S T A L L A T I O N
To install framed or overlay panels, see the detailed procedures outlined in the
Sub-Zero Undercounter Installation
Guide.
Refer to the fullscale illustrations at the end of this section for specifics on door openings and other specifications.
O V E R L A Y P A N E L S P E C I F I C A T I O N S
Undercounter Models
Models UC-24R and UC-24C
Door Panel Width
Door Panel Height
Panel Thickness
Panel Weight Limit
603 mm
764 mm
16 mm min
9 kg max
Model UC-24B
Door Panel Width
Door Panel Height
Width of Rails and Stiles
Panel Thickness
Panel Weight Limit
603 mm
764 mm
57 mm min
16 mm min
5 kg max
W
Illus. 1
H
W
Illus. 2
H
69
D O O R F R A M E P R O F I L E – M O D E L U C - 2 4 B
F U L L - S C A L E
T E M P L A T E S
The full-scale illustrations on the following pages enable you to understand some of the unique situations you may face as you plan for the installation of the Undercounter units. Use these illustrations as templates.
25 mm 25 mm
57 mm Rail / Stile
DOOR FRAME PROFILE
Glass
Door Panel Profile
The full-scale illustration shows the door frame profile for Model UC-24B.
IMPORTANT NOTE: Rails and stiles must be a minimum of 57 mm wide. The back sides of rails and stiles that will be visible through the glass door will need to be finished.
W I N E S H E L F W O O D F A C I N G – M O D E L S U C - 2 4 B A N D U C - 2 4 C
16 mm Maximum Thickness
3 mm
38 mm
21 mm
2 mm
495 mm
FRONT VIEW
For Models UC-24B and UC-24C, use the full-scale illustration above as a template if you choose to replace the natural cherry wood facing with wood more complementary to your design and surrounding cabinetry.
9 mm
14 mm
SIDE VIEW
70
U N D E R C O U N T E R D O O R C L O S E D A N D 1 4 5 ˚ M A X O P E N I N G
610 mm
CABINETRY
OPENING
587 mm
TO BACK OF
APPLIANCE
SUB-ZERO DOOR
19 mm
DOOR PANEL
600 mm
DOOR PANEL
WIDTH
The full-scale illustration shows what considerations you need to make for the installation of the Undercounter unit and how the maximum door opening may interact with adjacent cabinets and countertops.
145 ˚ *
13 mm
*
UNDERCOUNTER
UNIT MUST EXTEND
A MINIMUM 6 mm
BEYOND THE FRONT
SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
3 mm
6 mm*
SUB-ZERO
DOOR
DOOR
PANEL
71
7 0 0 1 8 7 1 2 / 2 0 0 7
SUB-ZERO, INC.
P O BOX 44130
MADISON, WI 53744 USA
SUBZERO.COM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project