Generic Qseven Carrier Board Harware User

Generic Qseven Carrier Board Hardware User Guide
iW-RainboW-G15D
Qseven Generic Carrier Board
Hardware User Guide
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 1 of 168
Generic Qseven Carrier Board Hardware User Guide
Document Revision History
Document Name
Revision
Date
1.0
1.1
1.2
1.3
2.0
2.1
2.2
iW-PRDVD-UM-01-R4.0-REL2.2
Description
16th Mar 2012 Initial Release Version
6th July 2012 Carrier expansion connector with mechanical
details added
1st Mar 2013 New Revision Board-R3.0 releated updates
9th Mar 2013 Added MIPI camera link and Part Number
04th Apr 2013 Official Release Version for R3.0 Generic
Carrier Board
th
24 July 2013 Official Release Version for R4.0 Generic
Carrier Board
rd
03 April 2015 APPENDIX IV is added with important note for
Debug USB Cable Connecting Procedure
Authors
Raghavendra C
Raghavendra C
Salma, Roshan
Salma
Salma, Pradap
Salma, Immanuel
Jaffir
PROPRIETARY NOTICE: This document contains proprietary material for the sole use of the intended
recipient(s). Do not read this document if you are not the intended recipient. Any review, use,
distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or
authorized to receive for the recipient), you are hereby notified that any disclosure, copying distribution
or use of any of the information contained within this document is STRICTLY PROHIBITED. Thank you.
“iWave Systems Tech. Pvt. Ltd.”
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 2 of 168
Generic Qseven Carrier Board Hardware User Guide
Disclaimer
iWave Systems reserves the right to change details in this publication including but not limited to any
Product specification without notice.
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by iWave Systems, its subsidiaries or employees for any direct or indirect
loss or damage caused by omissions from or inaccuracies in this document.
Trademarks
All registered trademarks and product names mentioned in this publication are used for identification
purposes only.
Technical Support
iWave Systems technical support team is committed to provide the best possible support for our
customers so that our Hardware and Software can be easily migrated and used.
For assistance, contact our Technical Support team at,
Address
Email
Website
: iWave Systems Technologies Pvt. Ltd.
# 7/B, 29th Main,
BTM Layout 2nd Stage,
Bangalore,
India – 560076
: [email protected]
: www.iwavesystems.com
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 3 of 168
Generic Qseven Carrier Board Hardware User Guide
Table of Contents
1
INTRODUCTION....................................................................................................................... 10
1.1
1.2
1.3
1.4
2
PURPOSE ............................................................................................................................... 10
QSEVEN OVERVIEW .............................................................................................................. 10
LIST OF ACRONYMS .............................................................................................................. 10
REFERENCE........................................................................................................................... 11
Qseven GENERIC CARRIER BOARD DESIGN ..................................................................... 12
2.1
QSEVEN GENERIC CARRIER BOARD BLOCK DIAGRAM .......................................................... 12
2.2
QSEVEN GENERIC CARRIER BOARD FEATURES ..................................................................... 13
2.3
QSEVEN MXM CONNECTOR ................................................................................................. 16
2.4
SERIAL INTERFACE FEATURES .............................................................................................. 29
2.4.1 Debug UART console ...................................................................................................... 29
2.4.2 UART0 header for iWave GPS ......................................................................................... 30
2.5
COMMUNICATION FEATURES ................................................................................................ 32
2.5.1 Gigabit Ethernet ............................................................................................................... 32
2.5.2 SDIO Ports ....................................................................................................................... 35
2.5.3 USB Ports ........................................................................................................................ 40
2.5.4 CAN Port1 ....................................................................................................................... 44
2.6
HIGH SPEED INTERFACE FEATURES ....................................................................................... 45
2.6.1 SATA............................................................................................................................... 45
2.6.2 PCI Express ...................................................................................................................... 48
2.7
AUDIO/ VIDEO FEATURES ..................................................................................................... 61
2.7.1 Audio In/Out .................................................................................................................... 61
2.7.2 LVDS Display Interface ................................................................................................... 63
2.7.3 HDMI Interface ................................................................................................................ 79
2.8
ADDITIONAL FEATURES ........................................................................................................ 82
2.8.1 JTAG Connector .............................................................................................................. 82
2.8.2 RTC Battery ..................................................................................................................... 84
2.8.3 Control Buttons ................................................................................................................ 85
2.8.4 EEPROM (Optional) ........................................................................................................ 88
2.8.5 Sensors ............................................................................................................................. 89
2.8.6 Add-on Headers ............................................................................................................... 91
2.9
EXPANSION CONNECTORS..................................................................................................... 99
2.9.1 UART2 Header .............................................................................................................. 118
2.9.2 CAN Port2 ..................................................................................................................... 119
2.9.3 TV-In RCA Jack............................................................................................................. 121
2.9.4 CMOS Camera Connector .............................................................................................. 122
2.9.5 MIPI Camera Connector ................................................................................................. 126
2.9.6 Keypad Header ............................................................................................................... 129
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 4 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.7
2.9.8
2.9.9
3
TV Out Header ............................................................................................................... 131
VGA Interface Header (Optional) ................................................................................... 132
Carrier Board Expansion Connector ................................................................................ 134
ELECTRICAL SPECIFICATION ........................................................................................... 144
3.1
3.2
QSEVEN GENERIC CARRIER BOARD POWER INPUT REQUIREMENT ...................................... 144
POWER OUTPUT TO QSEVEN CPU MODULE ........................................................................ 145
4
MECHANICAL SPECIFICATION ......................................................................................... 146
5
APPENDIX I ............................................................................................................................. 147
5.1
6
APPENDIX II............................................................................................................................ 149
6.1
6.2
6.3
7
EXPANSION PIN-OUT BASED ON I.MX6 SOM....................................................................... 149
EXPANSION PIN-OUT BASED ON AM389X SOM................................................................... 155
EXPANSION PIN-OUT BASED ON I.MX51 SOM..................................................................... 161
APPENDIX III .......................................................................................................................... 167
7.1
8
GENERIC QSEVEN CARRIER BOARD PCB SILK SCREEN ....................................................... 147
IWAVE’S COMPATIBLE QSEVEN CPU MODULES ................................................................. 167
APPENDIX IV .......................................................................................................................... 168
8.1
DEBUG UART USB CABLE CONNECTING PROCEDURE ....................................................... 168
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 5 of 168
Generic Qseven Carrier Board Hardware User Guide
List of Figures
Figure 1: Qseven Generic Carrier Board Block Diagram .......................................................................... 12
Figure 2: Qseven MXM Connector ......................................................................................................... 16
Figure 3: Debug UART Connector ........................................................................................................... 29
Figure 4: UART0 header ......................................................................................................................... 31
Figure 5: RJ45 (GBE), USB Host0 & Host2 Connector .............................................................................. 32
Figure 6: SD/MMC Card Connector ........................................................................................................ 35
Figure 7: SDIO Wi-Fi Module Connector ................................................................................................. 38
Figure 8: USB 2.0 OTG Connector .......................................................................................................... 41
Figure 9: USB 2.0 Connector .................................................................................................................. 43
Figure 10: CAN Port1 Connector ............................................................................................................ 44
Figure 11: SATA Port0 Connector ........................................................................................................... 45
Figure 12: SATA Port1 Connector ........................................................................................................... 47
Figure 13: PCIe x1 Connector ................................................................................................................. 49
Figure 14: PCIe Port2 Header ................................................................................................................. 52
Figure 15: PCIe Port3 Header ................................................................................................................. 54
Figure 16: Mini PCIe Connector ............................................................................................................. 56
Figure 17: Audio Jack ............................................................................................................................. 61
Figure 18: LVDS0 Connector .................................................................................................................. 64
Figure 19: 7`` Resistive LCD Connector ................................................................................................... 68
Figure 20: 7`` Capacitive Touch LCD Connector ...................................................................................... 72
Figure 21: LVDS1 Connectors ................................................................................................................. 76
Figure 22: HDMI Port ............................................................................................................................. 79
Figure 23: JTAG Connector .................................................................................................................... 82
Figure 24: RTC Battery ........................................................................................................................... 84
Figure 25: Power Button ........................................................................................................................ 85
Figure 26: Reset Button ......................................................................................................................... 86
Figure 27: Tamper Switch ...................................................................................................................... 87
Figure 28: EEPROM ................................................................................................................................ 88
Figure 29: Sensors ................................................................................................................................. 89
Figure 30: SPI Header ............................................................................................................................ 91
Figure 31: LPC Header ........................................................................................................................... 93
Figure 32: SDVO Header ........................................................................................................................ 95
Figure 33: Qseven Control Signal ........................................................................................................... 97
Figure 34: Expansion Connector 1 ........................................................................................................ 100
Figure 35: Expansion Connector 2 ........................................................................................................ 109
Figure 36: Secondary UART Connector................................................................................................. 118
Figure 37: Secondary CAN Connector .................................................................................................. 120
Figure 38: TV-IN Connector.................................................................................................................. 121
Figure 39: Camera Connector .............................................................................................................. 123
Figure 40: 5MP MIPI Camera connector............................................................................................... 126
Figure 41: Keypad Connector ............................................................................................................... 129
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 6 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 42: TV Out Interface Header ..................................................................................................... 131
Figure 43: VGA Signal Header .............................................................................................................. 132
Figure 44: Carrier Expansion Connector ............................................................................................... 134
Figure 45: Power Jack .......................................................................................................................... 144
Figure 46: Power Sequence to Qseven CPU Module ............................................................................ 145
Figure 47: Board Mechanical Dimension .............................................................................................. 146
Figure 48: PCB Silkscreen Top .............................................................................................................. 147
Figure 49: PCB Silkscreen Bottom ........................................................................................................ 148
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 7 of 168
Generic Qseven Carrier Board Hardware User Guide
List of Tables
Table 1: Acronyms & Abbreviations ....................................................................................................... 10
Table 2: Qseven MXM Connector Pin Out .............................................................................................. 17
Table 3: Debug UART Connector Pin Out ............................................................................................... 30
Table 4: UART0 header Pin Outs ............................................................................................................ 31
Table 5: Gigabit Ethernet Connector Pin Out ......................................................................................... 33
Table 6: SD/MMC Connector Pin Out ..................................................................................................... 36
Table 7: SDIO Wi-Fi Module Connector Pin Out ..................................................................................... 38
Table 8: USB 2.0 Host Ports Connector Pin Outs .................................................................................... 40
Table 9: USB 2.0 OTG Connector Pin Out ............................................................................................... 42
Table 10: USB 2.0 Host Port4 Connector Pin Out.................................................................................... 43
Table 11: CAN Port1 DB9 Connector Pin Out .......................................................................................... 44
Table 12: SATA Port0 Connector Pin Out................................................................................................ 46
Table 13: SATA Port1 Connector Pin Out................................................................................................ 48
Table 14: PCIe x1 Connector Pin Out ...................................................................................................... 49
Table 15: PCIe Port2 Header Pin Out...................................................................................................... 53
Table 16: PCIe Port3 Header Pin Out...................................................................................................... 55
Table 17: Mini PCIe Connector Pin Out .................................................................................................. 57
Table 18: SIM Connector Pin Out ........................................................................................................... 60
Table 19: Audio OUT Jack Pin Out .......................................................................................................... 62
Table 20: Audio IN Jack Pin Out ............................................................................................................. 62
Table 21: LVDS0 Connector Pin Out ....................................................................................................... 65
Table 22: LVDS0 Backlight Connector Pin Out ........................................................................................ 66
Table 23: 7`` RGB Resistive LCD Connector Pin Out ................................................................................ 68
Table 24: Resistive Touch Connector Pin Out ......................................................................................... 70
Table 25: 7`` Capacitive Touch LCD Connector Pin Out ........................................................................... 73
Table 26: Capacitive touch Connector Pin Out ....................................................................................... 74
Table 27: Backlight LED Pin Out ............................................................................................................. 74
Table 28: LVDS1 Connector Pin Out ....................................................................................................... 77
Table 29: LVDS1 Backlight Connector Pin Out ........................................................................................ 78
Table 30: HDMI Port Pin Out .................................................................................................................. 80
Table 31: JTAG Connector Pin Out ......................................................................................................... 83
Table 32: SPI Header Pin Out ................................................................................................................. 92
Table 33: LPC Header Pin Out ................................................................................................................ 93
Table 34: SDVO Header Pin Out ............................................................................................................. 95
Table 35: Qseven Control Signal Header ................................................................................................ 98
Table 36: Expansion Connector1 Pin Out ............................................................................................. 101
Table 37: Expansion Connector2 Pin Out ............................................................................................. 110
Table 38: Secondary UART Connector Pin Out ..................................................................................... 119
Table 39: CAN Port2 Connector Pin Out ............................................................................................... 120
Table 40: TV-In Connector Pin Out ....................................................................................................... 121
Table 41: Camera Connector Pin Out ................................................................................................... 124
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 8 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 42: MIPI Camera Connector Pin Out ........................................................................................... 127
Table 43: Keypad Connector Pin Out.................................................................................................... 130
Table 44: TV Out Header Pin Out ......................................................................................................... 131
Table 45: VGA Header Pin Out ............................................................................................................. 133
Table 46: Carrier Expansion Connector Pin Outs .................................................................................. 135
Table 47: Power Jack Pin Out ............................................................................................................... 144
Table 48: Power Output to Qseven CPU Modules ................................................................................ 145
Table 49: Power Sequence Timing to Qseven CPU Module .................................................................. 145
Table 50: Carrier Board Expansion Connector pin-out based on i.MX6 SOM......................................... 149
Table 51: Carrier Board Expansion Connector pin-out based on AM389x SOM ..................................... 155
Table 52: Carrier Board Expansion Connector pin-out based on i.MX51 SOM ....................................... 161
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 9 of 168
Generic Qseven Carrier Board Hardware User Guide
1
1.1
INTRODUCTION
Purpose
This document is the Hardware Reference Manual for the Qseven Generic Carrier Board. This board is
fully supported by iWave Systems Technologies Pvt. Ltd. This Manual includes system setup, debugging
and provides detailed information on the overall design and usage of the Qseven Generic Carrier Board
from a Hardware Systems perspective.
1.2
Qseven Overview
The Qseven concept is an off-the-shelf, multi-vendor, Single-Board-Computer that integrates all the core
components of a common PC and is mounted onto an application specific carrier board. Qseven
modules have a standardized form factor of 70mm x 70mm and have specified pinouts based on the
high speed MXM system connector that has a standardized pinout regardless of the vendor.
The Qseven module provides the functional requirements for an embedded application. These functions
include, but are not limited to, graphics, sound, mass storage, network and multiple USB ports. A single
ruggedized MXM connector provides the carrier board interface to carry all the I/O signals to and from
the Qseven module. This MXM connector is a well-known and proven high speed signal interface
connector that is commonly used for high speed PCI Express graphics cards in notebooks.
iWave’s Qseven Generic carrier board is also incorporated with additional two 80pin expansion
connectors which can be used to connect iWave’s Qseven CPU modules. These Expansion connectors
bring the additional interfaces to carrier boards which are not supported by Qseven Edge connector.
1.3
List of Acronyms
The following acronyms will be used throughout this document.
Table 1: Acronyms & Abbreviations
Acronyms
AC’97
ARM
BPP
CAN
CSI
EEPROM
GBE
GPIO
Description
Audio Codec ‘97
Advanced RISC Machine
Bits Per Pixel
Controller Area Network
Camera Sensor Interface
Electrically Erasable Programmable Read Only Memory
Gigabit Ethernet
General Purpose Input Output
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 10 of 168
Generic Qseven Carrier Board Hardware User Guide
HDMI
I2C
IC
I/O
JTAG
KB
LCD
LDO
LED
LVDS
MB
Mbps
MHz
MIPI
MMC
OTG
PCB
PCI
PWM
RGB
RJ45
RTC
SATA
SD
SDIO
SPI
SSI
TMDS
UART
USB
Wi-Fi
1.4
High-Definition Multimedia Interface
Inter-Integrated Circuit
Integrated Circuit
Input/Output
Joint Test Action Group
Kilo Byte
Liquid Crystal Display
Low Drop-Out
Light Emitting Diode
Low-Voltage Differential Signalling
Mega Byte
Mega Bits per sec
Mega Hertz
Mobile Industry Processor Interface
Multi Media Card
On the Go
Printed Circuit board
Peripheral Controller Interconnect
Pulse Width Modulation
Red Green Blue
Registered Jack 45
Real Time Clock
Serial Advanced Technology Attachment
Secure Digital
Secure Digital Input Output
Serial Peripheral Interface
Synchronous Serial Interface
Transition-Minimized Differential Signalling
Universal Asynchronous Receiver Transmitters
Universal Serial bus
Wireless Fidelity
Reference

Qseven Specification Revision 2.0

Qseven® Design Guide
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 11 of 168
Generic Qseven Carrier Board Hardware User Guide
2
Qseven GENERIC CARRIER BOARD DESIGN
This section is designed to provide detailed information about the electrical design and practical
considerations that went into the Qseven Generic Carrier Board. This section is organized to discuss
each block in the following high level block diagram, as shown below.
2.1
Qseven Generic Carrier Board Block Diagram
22-Pin Conn
SATA Port 0
7-Pin Conn
SATA Port 1
LVDS Channel 1
20-Pin LVDS
Conn with BL Conn
20-Pin LVDS
Conn with BL Conn
7” RGB LCD with
Capacitive TP Conn
+5V Input
+5V Standby Input
Reset Button
LVDS Channel 0
RGB-24bit
RTC Battery Holder
USB Port 3
PCIe0
4-Port PCIe
Switch*
SW_PCIe1
SW_PCIe2
PCIe to Dual
USB 3.0
Controller*
SW_PCIe3
Mini PCIe Conn*
PCIe x 1 Slot
I2C
Capacitive TP Conn
PCIe2
Touch
Controller
AC’97 CODEC
TMDS
HDMI Conn
Qseven
MXM Connector
(230-pin Connector)
Dual Stack USB 3.0
Conn*
PCIe Port2 Header*
SMB
PCIe3
AC’97
MIC/SPKR
PCIe Port3 Header*
USB Port 0
USB Port 2
USB Port 4
Dual Stack USB 2.0
Conn
TypeA USB 2.0 Conn
USB Port 1
Micro AB Conn
Ethernet
RJ45 MagJack
USB OTG
miniAB* Conn
SD Conn (8bit)
JTAG
UART
SD/MMC
SD Wi-Fi
SPI
SPI Header
SDVO
SDVO Header*
Qseven Control
Signal Header*
Push Button*
RTC
LVDS
Receiver
EEPROM*
Audio Jacks
Push Button
Tamper Switch
7” RGB LCD with
Resistive TP Conn*
Resistive TP
Conn
Push Button
Power Button
UART3
Qseven CTRL Signals
Micro AB Conn
GPS Conn
CAN
Tx Rx
CAN0
LPC
LPC Header*
DB9 Conn*
RS232
Tx Rx
UART to USB
Converter IC
DB9 Conn
I2C
Digital eCompass
Ambient Light
Sensor
3-Axis
Accelerometer
Altimeter/
Barometer
GPIO
MIPI-DSI
24bpp RGB LCD
120 pin Carrier
Expansion
Connector
80 pin Expansion
Connector - 1
UART2
RS232
Tx Rx
UART Header
CAN1
CAN
TxRX
CAN Header
TV IN
Decoder
RCA Jack
ESAI
CSI1
4-Wire
CSI2
Camera Conn
MLB
Memory Bus (Address/Data Muxed)
GPIO
Analog RGB
80 pin Expansion
Connector - 2
TV OUT Header
VGA
VGA Header*
4x4 Matrix
MIPI CSI
MIPI Camera Conn
*Optional
Power Jack
Keypad Header
+12V DC Input MAIN
Figure 1: Qseven Generic Carrier Board Block Diagram
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 12 of 168
Generic Qseven Carrier Board Hardware User Guide
2.2
Qseven Generic Carrier Board Features
Qseven Generic Carrier Board supports the following features to validate Qseven Edge Connector
Interfaces and iWave’s Qseven CPU Module specific Expansion Connector interfaces.
Qseven Edge Connector Features
Serial Interface Features

Debug UART console through USB Micro AB Connector

UART0 header for iWave GPS
Communication Features


10/100/1000 Mbps Ethernet through RJ45MagJack
SDIO Ports
 SD/MMC Connector¹
 On board Taiyo Yuden SDIO Wi-Fi module “WYSAAVDX7”¹

USB Ports
 USB 2.0 Host x 2 Ports through Type-A Stacked Connector
 USB 2.0 OTG Port through Mini AB Connector
 USB 2.0 Host Port4 through Type A Connector
 Mini PCIe connector with USB 2.0 Host Interface²

CAN port1 through DB9 Connector
High Speed Interface Features

SATA
 22pin Serial ATA Connector for SATA port0
 7pin Serial ATA Connector for SATA port1

PCI Express
 PCIe x1 Connector from Qseven MXM Connector
 PCIe Port 2 - SMD Pad Header
 PCIe Port 3 - SMD Pad Header
 4-port PCIe Switch⁴ through PCIe Port0 (Optional)
 Mini PCIe Connector through PCIe Switch Port1²˒⁴
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 13 of 168
Generic Qseven Carrier Board Hardware User Guide
 PCIe to USB 3.0 Hub controller through PCIe Switch Port3 for USB 3.0 Host x 2⁴
Audio/Video Features

AC’97 Audio Codec with 3.5mm Audio IN/OUT jack

LVDS Display Interface
 20pin LVDS0 connector with backlight connector³
 7” RGB Resistive Touch LCD³
 7” RGB Capacitive Touch LCD³
 20pin LVDS1 connector with backlight connector

HDMI port
Additional Features

10-Pin JTAG Connector

RTC Coin cell Holder

Control Buttons
 Power On/Off Button
 Reset Button
 Tamper Switch (Optional)


EEPROM (Optional)
Sensors
 Ambient Light Sensor
 Digital eCompass
 3-Axis accelerometer
 Altimeter/Barometer

Add-on Headers
 SPI Header
 LPC Header
 SDVO Header
 Qseven control signal Header
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 14 of 168
Generic Qseven Carrier Board Hardware User Guide
Note:
1.
Either 8-bit MMC/SDIO or Wi-Fi Module only can be used at a time.
2. Mini PCIe connector supports both USB interface and PCIe interface.
3. Either LVDS0 connector or 7” RGB resistive LCD or 7” RGB capacitive LCD can be used at a time.
4. By default 4-Port PCIe switch and USB 3.0 controller are not populated.
iWave’s Qseven CPU Module specific Expansion Connector Features

UART2 Header

CAN port2 connector

TV-In Composite Video through RCA Jack

8bit CMOS Camera Connector

MIPI Camera Connector

4X4 Keypad Header

TV Out Composite Video Header

VGA Interface Header

120-pin Carrier Board Expansion Connector
General Specification

Power Supply : 12V, 2A Power Input Jack

LED Indicators
 Power Indicator Red LEDs
 Reset Indicator Red LED

Temperature : 0°C to +60°C

Form Factor
: 120mm X 120mm Nano ITX
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 15 of 168
Generic Qseven Carrier Board Hardware User Guide
2.3
Qseven MXM Connector
The Qseven module utilizes a 230-pin board-edge connector that is also used for PCI Express capable
notebook graphics cards following the MXM specification. Therefore this connector type is also known
as MXM connector. The MXM connector (J12) is a robust, low-cost edge connector that is capable of
handling high-speed serialized signals.
Figure 2: Qseven MXM Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 16 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 2: Qseven MXM Connector Pin Out
Pin
No.
1
2
3
Edge Connector
Pin Name
GND1
GND2
GBE_MDI3-
Signal Type
Power
Power
Input/Output
Voltage Level/
Termination
0V
0V
Differential
4
GBE_MDI2-
Input/Output
Differential
5
GBE_MDI3+
Input/Output
Differential
6
GBE_MDI2+
Input/Output
Differential
7
8
9
GBE_LINK100#
GBE_LINK1000#
GBE_MDI1-
Input
Input
Input/Output
3.3V CMOS
3.3V CMOS
Differential
10
GBE_MDI0-
Input/Output
Differential
11
GBE_MDI1+
Input/Output
Differential
12
GBE_MDI0+
Input/Output
Differential
13
14
15
GBE_LINK#
GBE_ACT#
GBE_CTREF
Input
Input
Power In
3.3V CMOS
3.3V CMOS
3.3V
16
SUS_S5#
Input
3.3V CMOS
17
WAKE#
Output
3.3V CMOS
18
SUS_S3#
Input
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
Ground.
Ground.
Gigabit Ethernet MDI differential pair 3
negative.
Gigabit Ethernet MDI differential pair 2
negative.
Gigabit Ethernet MDI differential pair 3
positive.
Gigabit Ethernet MDI differential pair 2
positive.
100Mbps Ethernet Link status LED.
Gigabit Ethernet Link status LED.
Gigabit Ethernet MDI differential pair 1
negative.
Gigabit Ethernet MDI differential pair 0
negative.
Gigabit Ethernet MDI differential pair 1
positive.
Gigabit Ethernet MDI differential pair 0
positive.
Gigabit Ethernet Link status LED.
Gigabit Ethernet Activity status LED.
Reference
voltage
for
Ethernet
magnetic centre tap.
Soft Off State.
Default NC.
External system wake event.
Default NC.
Connected to 8th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Suspend to RAM.
Default NC.
Rev 2.2
Page 17 of 168
Generic Qseven Carrier Board Hardware User Guide
19
SUS_STAT#
Input
3.3V CMOS
20
PWRBTN#
Output
21
SLP_BTN#
Output
3.3V CMOS/
10K Pull-up
3.3V CMOS
22
LID_BTN#
Output
3.3V CMOS
LID Button.
Default NC.
Connected to 6th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
23
24
25
26
GND3
GND4
GND5
PWGIN
Power
Power
Power
Output
Ground.
Ground.
Ground.
Power good input.
27
BATLOW#
Output
0V
0V
0V
5V CMOS/
10K Pull-up
3.3V CMOS
28
RSTBTN#
Output
3.3V CMOS
29
SATA0_TX+
Input
Differential
30
SATA1_TX+
Input
Differential
31
SATA0_TX-
Input
Differential
Active low Reset button.
Connected to push button S2.
SATA0 Transmit Input differential
positive.
SATA1 Transmit Input differential
positive.
SATA0 Transmit Input differential
negative.
iWave Systems Technologies Pvt. Ltd.
Suspend Status.
Default NC.
Connected to 3rd Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Power button.
Connected to push button S1.
Sleep button.
Default NC.
Connected to 5th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Battery low indication.
Default NC.
Connected to 9th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Rev 2.2
Page 18 of 168
Generic Qseven Carrier Board Hardware User Guide
32
SATA1_TX-
Input
Differential
33
34
35
SATA_ACT#
GND6
SATA0_RX+
Input
Power
Output
3.3V CMOS
0V
Differential
36
SATA1_RX+
Output
Differential
37
SATA0_RX-
Output
Differential
38
SATA1_RX-
Output
Differential
39
40
41
GND7
GND8
BIOS_DISABLE#/
BOOT_ALT#
Power
Power
Output
0V
0V
3.3V CMOS
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
SDIO_CLK#
SDIO_CD#
SDIO_LED
SDIO_CMD
SDIO_WP
SDIO_PWR#
SDIO_DAT1
SDIO_DAT0
SDIO_DAT3
SDIO_DAT2
SDIO_DAT5
SDIO_DAT4
SDIO_DAT7
SDIO_DAT6
RSVD1
Input
Output
Input
Input/Output
Output
Input
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
NC
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
NC
iWave Systems Technologies Pvt. Ltd.
SATA1 Transmit Input differential
negative.
SATA command Activity line.
Ground.
SATA0 Receive Output differential
positive.
SATA1 Receive Output differential
positive.
SATA0 Receive Output differential
negative.
SATA1 Receive Output differential
negative.
Ground.
Ground.
Default NC.
Connected to 10th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
SD/MMC card clock.
SD/MMC card Detect pin.
SD/MMC card indication LED.
SD/MMC card Command line.
SD/MMC card Write Protect pin.
SD/MMC card Power Enable pin.
SD/MMC card Data Line (Bit1).
SD/MMC card Data Line (Bit0).
SD/MMC card Data Line (Bit3).
SD/MMC card Data Line (Bit2).
SD/MMC card Data Line (Bit5).
SD/MMC card Data Line (Bit4).
SD/MMC card Data Line (Bit7).
SD/MMC card Data Line (Bit6).
Default NC.
Connected to 1st Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Rev 2.2
Page 19 of 168
Generic Qseven Carrier Board Hardware User Guide
57
58
59
Power
Power
Input
0V
0V
3.3V CMOS
Input
3.3V CMOS
Ground.
Ground.
Audio Transmit frame synchronization
line.
System Management Bus Clock.
Input
3.3V CMOS
Audio reset.
Input/Output
3.3V CMOS
System Management Bus Data.
Input
3.3V CMOS
Audio Transmit Clock line.
64
GND9
GND10
HDA_SYNC/
I2S_WS
SMB_CLK/
GP1_I2C_CLK
HDA_RST#/
I2S_RST#
SMB_DAT/
GP1_I2C_DAT
HDA_BITCLK/
I2S_CLK
SMB_ALERT#
Output
3.3V CMOS
65
66
HDA_SDI/ I2S_SDI
GP0_I2C_CLK
Output
Input
67
Input
68
HDA_SDO/
I2S_SDO
GP0_I2C_DAT
3.3V CMOS
3.3V CMOS/
4.7K Pull-up
3.3V CMOS
System Management Bus Alert input.
Default NC.
Connected to 3rd Pin of SDVO Header
(J47) through resistor and default not
populated.
Audio Transmit data line.
I2C Clock signal.
69
THRM#
Output
3.3V CMOS/
4.7K Pull-up
3.3V CMOS
70
WDTRIG#
Output
3.3V CMOS
71
THRMTRIP#
Input
3.3V CMOS
60
61
62
63
Input/Output
iWave Systems Technologies Pvt. Ltd.
Audio Receive data line.
I2C Data signal.
Thermal Alarm active low signal.
Connected to 11th Pin of Qseven Control
Signal Header (J53).
Watchdog trigger signal.
Default NC.
Connected to 2nd Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Thermal Trip indicates an overheating
condition of the Processor.
Connected to 12th Pin of Qseven Control
Signal Header (J53).
Rev 2.2
Page 20 of 168
Generic Qseven Carrier Board Hardware User Guide
72
WDOUT
Input
3.3V CMOS
73
74
75
GND11
GND12
USB_P7-/
USB_SSTX0USB_P6-/
USB_SSRX0USB_P7+/
USB_SSTX0+
USB_P6+/
USB_SSRX0+
USB_6_7_OC#
Power
Power
Input/Output
0V
0V
Differential
Watchdog event indicator input.
Default NC.
Connected to 4th Pin of Qseven Control
Signal Header (J53) through resistor and
default not populated.
Ground.
Ground.
USB Host Port7 Data negative.
Input/Output
Differential
USB Host Port6 Data negative.
Input/Output
Differential
USB Host Port7 Data positive.
Input/Output
Differential
USB Host Port6 Data positive.
Output
3.3V CMOS
USB_4_5_OC#
USB_P5-/
USB_SSTX1USB_P4-/
USB_SSRX1USB_P5+/
USB_SSTX1+
USB_P4+/
USB_SSRX1+
USB_2_3_OC#
USB_0_1_OC#
USB_P3USB_P2USB_P3+
USB_P2+
USB_CC
USB_ID
USB_P1-
Output
Input/Output
3.3V CMOS
Differential
Over current sense for USB ports 6 & 7.
Connected to 114th Pin of Carrier board
Expansion connector (J10).
Over current sense for USB port 4 & 5.
USB Host Port5 Data Negative.
Input/Output
Differential
USB Host Port4 Data negative.
Input/Output
Differential
USB Host Port5 Data Positive.
Input/Output
Differential
USB Host Port4 Data Positive.
Output
Output
Input/Output
Input/Output
Input/Output
Input/Output
Output
Output
Input/Output
3.3V CMOS
3.3V CMOS
Differential
Differential
Differential
Differential
3.3V CMOS
3.3V CMOS
Differential
Over current sense for USB port 2 & 3.
Over current sense for USB port 0 & 1.
USB Host Port3 Data negative.
USB Host Port2 Data negative.
USB Host Port3 Data Positive.
USB Host Port2 Data Positive.
USB client connect.
USB OTG ID to identify Host & device.
USB OTG Data negative.
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 21 of 168
Generic Qseven Carrier Board Hardware User Guide
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
USB_P0USB_P1+
USB_P0+
GND13
GND14
eDP0_TX0+/
LVDS_A0+
eDP1_TX0+/
LVDS_B0+
eDP0_TX0-/
LVDS_A0eDP1_TX0-/
LVDS_B0eDP0_TX1+/
LVDS_A1+
eDP1_TX1+/
LVDS_B1+
eDP0_TX1-/
LVDS_A1eDP1_TX1-/
LVDS_B1eDP0_TX2+/
LVDS_A2+
eDP1_TX2+/
LVDS_B2+
eDP0_TX2-/
LVDS_A2eDP1_TX2-/
LVDS_B2LVDS_PPEN
LVDS_BLEN
Input/Output
Input/Output
Input/Output
Power
Power
Input
Differential
Differential
Differential
0V
0V
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
Input
3.3V CMOS
3.3V CMOS
eDP0_TX3+/
LVDS_A3+
eDP1_TX3+/
LVDS_B3+
Input
LVDS
Input
LVDS
iWave Systems Technologies Pvt. Ltd.
USB Host Port0 Data negative.
USB OTG Data Positive.
USB Host Port0 Data Positive.
Ground.
Ground.
LVDS primary channel differential pair0
positive.
LVDS secondary channel differential
pair0 positive.
LVDS primary channel differential pair0
negative.
LVDS secondary channel differential
pair0 negative.
LVDS primary channel differential pair1
positive.
LVDS secondary channel differential
pair1 positive.
LVDS primary channel differential pair1
negative.
LVDS secondary channel differential
pair1 negative.
LVDS primary channel differential pair2
positive.
LVDS secondary channel differential
pair2 positive.
LVDS primary channel differential pair2
negative.
LVDS secondary channel differential
pair2 negative.
LVDS LCD panel power enable control.
LVDS LCD panel Backlight enable
control.
LVDS primary channel differential pair3
positive.
LVDS secondary channel differential
pair3 positive.
Rev 2.2
Page 22 of 168
Generic Qseven Carrier Board Hardware User Guide
115
eDP0_TX3-/
LVDS_A3eDP1_TX3-/
LVDS_B3GND15
GND16
eDP0_AUX+/
LVDS_A_CLK+
eDP1_AUX+/
LVDS_B_CLK+
eDP0_AUX-/
LVDS_A_CLKeDP1_AUX-/
LVDS_B_CLKLVDS_BLT_CTRL/
GP_PWM_OUT0
GP_1-Wire_Bus
GP2_I2C_DAT/
LVDS_DID_DAT
eDP0_HPD#/
LVDS_BLC_DAT
GP2_I2C_CLK/
LVDS_DID_CLK
eDP1_HPD#/
LVDS_BLC_CLK
CAN0_TX
CAN0_RX
DP_LANE3+/
TMDS_CLK+
Input
LVDS
Input
LVDS
Power
Power
Input
0V
0V
LVDS
Input
LVDS
Input
LVDS
Input
LVDS
Input
3.3V CMOS
Input/Output
Input/Output
Input
Output
Input
3.3V CMOS
3.3V CMOS/
4.7K Pull-up
3.3V CMOS/
4.7K Pull-up
3.3V CMOS/
4.7K Pull-up
3.3V CMOS/
4.7K Pull-up
3.3V CMOS
3.3V CMOS
TMDS
132
RSVD2
(Differential Pair)
NC
NC
Default NC.
Connected to 2nd Pin of SDVO Header
(J47) through resistor and default not
populated.
133
DP_LANE3-/
TMDS_CLK-
Input
TMDS
HDMI differential clock negative
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
Input/Output
Input
Input
iWave Systems Technologies Pvt. Ltd.
LVDS primary channel differential pair3
negative.
LVDS secondary channel differential
pair3 negative.
Ground.
Ground.
LVDS primary channel differential clock
positive.
LVDS secondary channel differential
clock positive.
LVDS primary channel differential clock
negative.
LVDS secondary channel differential
clock negative.
LVDS LCD Panel backlight brightness
control.
HDMI CEC bus.
Display ID DDC data line used for LVDS
flat panel detection.
Control data signal for external SSC
clock chip.
Display ID DDC clock line used for LVDS
flat panel detection.
Control clock signal for external SSC
clock chip.
CAN channel one TX line.
CAN channel one RX line
HDMI differential clock positive.
Rev 2.2
Page 23 of 168
Generic Qseven Carrier Board Hardware User Guide
134
RSVD3
(Differential Pair)
NC
NC
135
136
GND17
GND18
Power
Power
0V
0V
Default NC.
Connected to 4th Pin of SDVO Header
(J47) through resistor and default not
populated.
Ground.
Ground.
137
DP_LANE1+/
TMDS_LANE1+
DP_AUX+
Input
TMDS
HDMI differential data1 positive.
Input/Output
TMDS
DP_LANE1-/
TMDS_LANE1DP_AUX-
Input
TMDS
HDMI differential device control data
positive.
Default NC.
Connected to 6th Pin of SDVO Header
(J47) through resistor and default not
populated.
HDMI differential data1 negative.
Input/Output
TMDS
GND19
GND20
DP_LANE2+/
TMDS_LANE0+
RSVD4
(Differential Pair)
Power
Power
Input
0V
0V
TMDS
Input
TMDS
DP_LANE2-/
TMDS_LANE0RSVD5
(Differential Pair)
Input
TMDS
NC
NC
138
139
140
141
142
143
144
145
146
iWave Systems Technologies Pvt. Ltd.
HDMI differential device control data
negative.
Default NC.
Connected to 8th Pin of SDVO Header
(J47) through resistor and default not
populated.
Ground.
Ground.
HDMI differential data0 positive.
Default NC.
Connected to 10th Pin of SDVO Header
(J47) through resistor and default not
populated.
HDMI differential data0 negative.
Default NC.
Connected to 12th Pin of SDVO Header
(J47) through resistor and default not
populated.
Rev 2.2
Page 24 of 168
Generic Qseven Carrier Board Hardware User Guide
147
148
149
Power
Power
Input
0V
0V
TMDS
Ground.
Ground.
HDMI differential data2 positive.
Input/Output
Input
3.3V CMOS
TMDS
I2C2 Data signal.
HDMI differential data2 negative.
152
GND21
GND22
DP_LANE0+/
TMDS_LANE2+
HDMI_CTRL_DAT
DP_LANE0-/
TMDS_LANE2HDMI_CTRL_CLK
Input
I2C2 Clock signal.
153
154
DP_HDMI_HPD#
RSVD6
Output
NC
3.3V CMOS/
4.7K Pull-up
3.3V CMOS
NC
155
PCIE_CLK_REF+
Input
Differential
156
157
PCIE_WAKE#
PCIE_CLK_REF-
Output
Input
3.3V CMOS
Differential
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
PCIE_RST#
GND23
GND24
PCIE3_TX+
PCIE3_RX+
PCIE3_TXPCIE3_RXGND25
GND26
PCIE2_TX+
PCIE2_RX+
PCIE2_TXPCIE2_RXUART0_TX
UART0_RTS#
PCIE1_TX+
PCIE1_RX+
Input
Power
Power
Input
Output
Input
Output
Power
Power
Input
Output
Input
Output
Input
Input
Input
Output
3.3V CMOS
0V
0V
Differential
Differential
Differential
Differential
0V
0V
Differential
Differential
Differential
Differential
3.3V CMOS
3.3V CMOS
Differential
Differential
150
151
iWave Systems Technologies Pvt. Ltd.
HDMI Hot Plug Detect.
Default NC.
Connected to 9th Pin of SDVO Header
(J47) through resistor and default not
populated.
PCIe differential reference clock
positive.
PCIe interface wake up signal.
PCIe differential reference clock
negative.
PCIe Reset.
Ground.
Ground.
PCIe3 differential transmit line positive.
PCIe3 differential receive line positive.
PCIe3 differential transmit line negative.
PCIe3 differential receive line negative.
Ground.
Ground.
PCIe2 differential transmit line positive.
PCIe2 differential receive line positive.
PCIe2 differential transmit line negative.
PCIe2 differential receive line negative.
UART3 Transmit signal.
UART3 RTS signal.
PCIe1 differential transmit line positive.
PCIe1 differential receive line positive.
Rev 2.2
Page 25 of 168
Generic Qseven Carrier Board Hardware User Guide
175
176
177
178
179
180
181
182
183
184
185
PCIE1_TXPCIE1_RXUART0_RX
UART0_CTS#
PCIE0_TX+
PCIE0_RX+
PCIE0_TXPCIE0_RXGND27
GND28
LPC_AD0/GPIO0
Input
Output
Output
Output
Input
Output
Input
Output
Power
Power
Input/Output
Differential
Differential
3.3V CMOS
3.3V CMOS
Differential
Differential
Differential
Differential
0V
0V
3.3V CMOS
186
LPC_AD1/GPIO1
Input/Output
3.3V CMOS
187
LPC_AD2/GPIO2
Input/Output
3.3V CMOS
188
LPC_AD3/GPIO3
Input/Output
3.3V CMOS
189
LPC_CLK/GPIO4
Input/Output
3.3V CMOS
190
LPC_FRAME#/
GPIO5
Input/Output
3.3V CMOS
191
SERIRQ/GPIO6
Input/Output
3.3V CMOS
GPIO
Connected to MIPI power down signal
and to 11th Pin of LPC Header (J34).
192
LPC_LDRQ#/
GPIO7
Input/Output
3.3V CMOS
GPIO.
Connected to USB power switch and to
12th Pin of LPC Header (J34).
193
VCC_RTC
Power
3V
RTC battery voltage input.
iWave Systems Technologies Pvt. Ltd.
PCIe1 differential transmit line negative.
PCIe1 differential receive line negative.
UART3 Receive signal.
UART3 CTS signal.
PCIe0 differential transmit line positive.
PCIe0 differential receive line positive.
PCIe0 differential transmit line negative.
PCIe0 differential receive line negative.
Ground.
Ground
GPIO.
Connected to Touch Controller interrupt
and to 5th Pin of LPC Header (J34).
GPIO.
Connected to Digital eCompass
interrupt & 6th Pin of LPC Header (J34).
GPIO.
Connected to 3-Axis Accelerometer
interrupt & 7th Pin of LPC Header (J34).
GPIO.
Connected to Ambient Light Sensor
interrupt & 8th Pin of LPC Header (J34).
GPIO.
Connected to Altimeter/ Barometer
interrupt & 9th Pin of LPC Header (J34).
GPIO.
Connected to SATA and to 10th Pin of
LPC Header (J34).
Rev 2.2
Page 26 of 168
Generic Qseven Carrier Board Hardware User Guide
194
SPKR/
GP_PWM_OUT2
FAN_TACHOIN/
GP_TIMER_IN
Input
3.3V CMOS
Output
3.3V CMOS
196
FAN_PWMOUT/
GP_PWM_OUT1
Input
3.3V CMOS
197
198
199
GND29
GND30
SPI_MOSI
Power
Power
Input/Output
0V
0V
3.3V CMOS
200
SPI_CS0#
Input
3.3V CMOS
201
SPI_MISO
Input/Output
3.3V CMOS
202
SPI_CS1#
Input
3.3V CMOS
203
SPI_SCK
Input
3.3V CMOS
204
205
206
207
MFG_NC4
VCC_5V_SB1
VCC_5V_SB2
MFG_NC0
Output
Power
Power
Output
3.3V CMOS
5V
5V
3.3V CMOS
208
MFG_NC2
Output
3.3V CMOS
209
MFG_NC1
Input
3.3V CMOS
210
211
212
MFG_NC3
VCC1
VCC2
Output
Power
Power
3.3V CMOS
5V
5V
195
iWave Systems Technologies Pvt. Ltd.
PWM used to control the LVDS LCD
Backlight.
Fan tachometer input.
Default NC.
Connected to 5th Pin of SDVO Header
(J47) through resistor and default not
populated.
Fan PWM input.
Default NC.
Connected to 7th Pin of SDVO Header
(J47) through resistor and default not
populated.
Ground.
Ground.
SPI Master Out Slave In.
Connected to 4th Pin of SPI Header (J29).
SPI chip select 0.
Connected to 1st Pin of SPI Header (J29).
SPI Master In Slave Out.
Connected to 2nd Pin of SPI Header
(J29).
SPI chip select 1.
Connected to 7th Pin of SPI Header (J29).
SPI clock input.
Connected to 5th Pin of SPI Header (J29).
JTAG Reset Output.
Standby Power Supply.
Standby Power Supply.
JTAG Test Clock.
Debug UART RX data line UART2_RXD
(EIM_D27).
Debug UART TX data line. UART2_TXD
(EIM_D26).
JTAG Test Mode Select.
Input Supply Voltage.
Input Supply Voltage.
Rev 2.2
Page 27 of 168
Generic Qseven Carrier Board Hardware User Guide
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
VCC3
VCC4
VCC5
VCC6
VCC7
VCC8
VCC9
VCC10
VCC11
VCC12
VCC13
VCC14
VCC15
VCC16
VCC17
VCC18
VCC19
VCC20
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
iWave Systems Technologies Pvt. Ltd.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Input Supply Voltage.
Rev 2.2
Page 28 of 168
Generic Qseven Carrier Board Hardware User Guide
2.4
Serial Interface Features
2.4.1 Debug UART console
Debug UART signals from Qseven MXM connector is connected to UART to USB conversion and to USB
Micro AB Connector (J15). This Micro USB Connector can be used for Debug purpose. This is not the full
functional UART and supports only TX and RX signals.
Figure 3: Debug UART Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 29 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 3: Debug UART Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/
Termination
Description
1
DBUG_VBUS
Power
5V
Debug USB, 5V Power.
2
DBUG_USB_DM
Input/Outpu Differential
Debug USB, Data negative.
3
DBUG_USB_DP
Input/Outpu
Differential
Debug USB, Data positive.
t
4
NC
NC
NC
NC.
t
5
GND
Power
0V
Ground.
S1,S2,
DSUB_SHLD_GND Power
0V
Shield Ground.
S3,S4
Note: Refer “APPENDIX IV” for connecting Debug UART USB Cable Procedure
2.4.2 UART0 header for iWave GPS
Qseven Generic Carrier Board supports on board UART0 header (J2) through UART0 interface of Qseven
MXM connector. This header can be used to connect iWave’s GPS module and physically located on the
top of the board as shown below.
Number of Pins: 6
Connector Part number: 10114829-10106LF
Mating Connector: 10114826-00006LF from FCI
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 30 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 4: UART0 header
Table 4: UART0 header Pin Outs
Pin No
Pin Name
Signal Type
1
V_BCKUP
Power
Voltage Level/
Termination
3V
2
3
4
3.3V_MAIN
GND
UART_RXD
Power
Power
Input
3.3V
0V
3.3V CMOS
5
UART_TXD
Output
3.3V CMOS
6
NC
NC
NC
iWave Systems Technologies Pvt. Ltd.
Description
RTC battery voltage Input from RTC
battery.
Input voltage.
Ground.
UART receive signal.
Connected to 177th Pin of Qseven
MXM Connector.
UART transmit signal.
Connected from 171st Pin of Qseven
MXM Connector.
NC.
Rev 2.2
Page 31 of 168
Generic Qseven Carrier Board Hardware User Guide
2.5
Communication Features
2.5.1 Gigabit Ethernet
Gigabit Ethernet signals from Qseven MXM connector are connected to RJ45 MagJack (J25A-Top), with
LED indicators. RJ45 MagJack will work for both 10/100Mbps & 10/100/1000 Mbps Ethernet operation.
This connector is physically located on top of the board as shown below.
Figure 5: RJ45 (GBE), USB Host0 & Host2 Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 32 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 5: Gigabit Ethernet Connector Pin Out
Pin No
1
2
GND
TRD1+
Power
Input/Output
Voltage Level/
Termination
0V
Differential
3
TRD1-
Input/Output
Differential
4
TRD2+
Input/Output
Differential
5
TRD2-
Input/Output
Differential
6
CTREF
Power In
3.3V
7
TRD3+
Input/Output
Differential
8
Pin Name
TRD3-
Signal Type
Input/Output
iWave Systems Technologies Pvt. Ltd.
Differential
Description
Ground
Gigabit Ethernet MDI differential
pair 0 positive.
Connected to 12th Pin of Qseven
MXM Connector.
Gigabit Ethernet MDI differential
pair 0 negative.
Connected to 10th Pin of Qseven
MXM Connector.
Gigabit Ethernet MDI differential
pair 1 positive.
Connected to 11th Pin of Qseven
MXM Connector.
Gigabit Ethernet MDI differential
pair 1 negative.
Connected to 9th Pin of Qseven
MXM Connector.
Reference voltages for Gigabit
Ethernet magnetics centre tap
input.
Connected to 15th Pin of Qseven
MXM Connector.
Gigabit Ethernet MDI
pair 2 positive.
Connected to 6th Pin
MXM Connector.
Gigabit Ethernet MDI
pair 2 negative.
Connected to 4th Pin
MXM Connector.
differential
of Qseven
differential
of Qseven
Rev 2.2
Page 33 of 168
Generic Qseven Carrier Board Hardware User Guide
9
TRD4+
Input/Output
Differential
10
TRD4-
Input/Output
Differential
11
LED_Y-
Input
3.3V
12
LED_Y+
Input
3.3V
13
LED_G-
Input
3.3V
14
LED_GO+
Input
3.3V
15
LED_O-
Input
3.3V
SHLD
Power
0V
S5,S6,S7,S8
iWave Systems Technologies Pvt. Ltd.
Gigabit Ethernet MDI differential
pair 3 positive.
Connected to 5th Pin of Qseven
MXM Connector.
Gigabit Ethernet MDI differential
pair 3 negative.
Connected to 3rd Pin of Qseven
MXM Connector.
Gigabit Ethernet Activity status LED
Yellow Cathode.
Connected to 14th Pin of Qseven
MXM Connector.
LED Yellow Anode.
Connected to 3.3V power.
100Mbps Ethernet Link status LED
Green Cathode.
Connected to 7th Pin of Qseven
MXM Connector.
LED Green/Orange Anode.
Connected to 3.3V power.
Gigabit Ethernet Link status LED
Orange Cathode.
Connected to 13th Pin of Qseven
MXM Connector.
Shield Ground Ethernet.
Rev 2.2
Page 34 of 168
Generic Qseven Carrier Board Hardware User Guide
2.5.2 SDIO Ports
Qseven Generic Carrier Board supports SD/MMC connector and Wi-Fi Module connector through SDIO
interface of Qseven MXM connector. Since SDIO interface is multiplexed between SD/MMC and Wi-Fi
Module, either one only can be used at a time. This can be selected by controlling SDIO_PWR# signal
from 47th pin of Qseven MXM connector. If SDIO_PWR# is low, SD/MMC is selected and if SDIO_PWR# is
high, Wi-Fi module is selected.
2.5.2.1 SD/MMC Connector
Qseven Generic Carrier Board supports SD/MMC Connector (J6) to support SD cards/MMC cards/SDIO
cards. This connector supports up to 8-bit data transfer with card detect & write protect feature. The
main power to SD/MMC connector is 3.3V. SD/MMC connector is physically located on top of the board
as shown below.
Figure 6: SD/MMC Card Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 35 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 6: SD/MMC Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/
Termination
3.3V CMOS/
2.2K Pull-up
1
WP
Input
2
CD
Input
3.3V CMOS
3
DAT1
Input/Output
3.3V CMOS
4
DAT0
Input/Output
3.3V CMOS
5
DAT7
Input/Output
3.3V CMOS
6
7
GND/VSS2
DAT6
Power
Input/Output
0V
3.3V CMOS
8
CLK
Output
3.3V CMOS
9
10
11
VCC/VDD
VSS1
DAT5
Power
Power
Input/Output
3.3V
0V
3.3V CMOS
12
CMD
Input/Output
3.3V CMOS/
10K Pull-up
13
DAT4
Input/Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
SD/MMC Write Protect pin.
Connected from 46th Pin of Qseven
MXM Connector.
SD/MMC card Detect pin.
Connected from 43rd Pin of Qseven
MXM Connector.
SD/MMC Data Line (Bit1).
Connected to 48th Pin of Qseven MXM
Connector.
SD/MMC Data Line (Bit0).
Connected to 49th Pin of Qseven MXM
Connector
SD/MMC Data Line (Bit7).
Connected to 54th Pin of Qseven MXM
Connector.
Ground
SD/MMC Data Line (Bit6).
Connected to 55th Pin of Qseven MXM
Connector.
SD/MMC Clock.
Connected to 42nd Pin of Qseven MXM
Connector.
Supply Voltage.
Ground.
SD/MMC Data Line (Bit5).
Connected to 52nd Pin of Qseven MXM
Connector.
SD/MMC Command.
Connected to 45th Pin of Qseven MXM
Connector.
SD/MMC Data Line (Bit4).
Connected to 53rd Pin of Qseven MXM
Connector.
Rev 2.2
Page 36 of 168
Generic Qseven Carrier Board Hardware User Guide
14
DAT3
Input/Output
3.3V CMOS
15
DAT2
Input/Output
3.3V CMOS
SD/MMC Data Line (Bit3).
Connected to 50th Pin of Qseven MXM
Connector.
SD/MMC Data Line (Bit2).
Connected to 51st Pin of Qseven MXM
Connector.
2.5.2.2 SDIO Wi-Fi Module
Qseven Generic Carrier Board supports on-board Wi-Fi Module connector to connect SDIO Wi-Fi
module. SDIO Wi-Fi module connector (J56) is physically located at the bottom of board as shown
below.
SDIO Wi-Fi Connector:
Number of Pins: 20
Connector Part number: AXK720147G or AXK720247G or AXK720347G or AXK720447G from Panasonic
Electric Works
Compatible Wi-Fi Module:
Part Number: WYSAAVDX7
Description: IEEE802.11b/g/n Wireless Module with Antenna
Manufacturer Name: TAIYO YUDEN
Note: Wi-Fi module will not be provided with the development kit and it is not part of the deliverable.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 37 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 7: SDIO Wi-Fi Module Connector
Table 7: SDIO Wi-Fi Module Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/
Termination
1
2
GND
WiFi_DATA1
Power
Input/Output
0V
3.3V CMOS
3
WiFi_DATA0
Input/Output
3.3V CMOS
4
GND
Power
0V
iWave Systems Technologies Pvt. Ltd.
Description
Ground
SD/MMC Data Line (Bit1).
Connected to 48th Pin of Qseven
MXM Connector.
SD/MMC Data Line (Bit0).
Connected to 49th Pin of Qseven
MXM Connector.
Ground.
Rev 2.2
Page 38 of 168
Generic Qseven Carrier Board Hardware User Guide
5
WiFi_CLK
Output
3.3V CMOS
6
7
VCC_3V3
WiFi_CMD
Power
Input/Output
8
WiFi_DATA3
Input/Output
3.3V
3.3V
CMOS/10K
Pull-up
3.3V CMOS
9
WiFi_DATA2
Input/Output
3.3V CMOS
10
11
12
GND
GND
SLEEP_CLK
Power
Power
Output
0V
0V
1.8V
13
14
GND
WIFI_PDN
Power
Output
0V
3.3V CMOS
15
16
MAIN_RESET#
WL_HOST_WKUP
Output
Output
3.3V CMOS
3.3V CMOS
17
HOST_WL_WKUP
Input
3.3V CMOS
18
19
20
M
GND
VCC_5V
VCC_5V
Mechanical
Support
Power
Power
Power
Mechanical
Support
0V
5V
5V
Mechanical
Support
iWave Systems Technologies Pvt. Ltd.
SD/MMC Clock.
Connected to 42nd Pin of Qseven
MXM Connector.
Power Supply.
SD/MMC Command.
Connected to 45th Pin of Qseven
MXM Connector.
SD/MMC Data Line (Bit3).
Connected to 50th Pin of Qseven
MXM Connector.
SD/MMC Data Line (Bit2).
Connected to 51st Pin of Qseven
MXM Connector.
Ground.
Ground.
External Sleep Clock (32.768KHz)
For low power mode.
Ground.
Wi-Fi Power Down.
Connected to 55th Pin of
Expansion Connector1.
Main Reset.
WLAN Wakeup.
Connected to 56th Pin of
Expansion Connector1.
Host Wakeup.
Connected from 57th
Expansion Connector1.
Ground.
Power Supply.
Power Supply.
Mechanical Support.
Pin
of
Rev 2.2
Page 39 of 168
Generic Qseven Carrier Board Hardware User Guide
2.5.3 USB Ports
2.5.3.1 USB Host0 & Host2 Ports
USB Host0 & Host2 interfaces from Qseven MXM connector are connected to dual stack USB Type-A
connector (J25B). Refer. Figure 5 for the connector location.
Table 8: USB 2.0 Host Ports Connector Pin Outs
Pin No
Pin Name
Signal Type
Voltage Level/
Termination
A1
A2
VBUS1
D1-
Power
Input/Output
5V
Differential
A3
D1+
Input/Output
Differential
A4
B1
B2
GND1
VBUS2
D2-
Power
Power
Input/Output
0V
5V
Differential
B3
D2+
Input/Output
Differential
GND2
SHLD
SHLD
Power
Power
Power
0V
0V
0V
B4
S1,S2
S3,S4
iWave Systems Technologies Pvt. Ltd.
Description
USB Host Port 0, 5V Power (Bottom).
USB Host Port 0, Data negative (Bottom).
Connected to 94th Pin of Qseven MXM
Connector.
USB Host Port 0, Data Positive (Bottom).
Connected to 96th Pin of Qseven MXM
Connector.
USB Host Port 0 Ground (Bottom).
USB Host Port 2, 5V Power (Top).
USB Host Port 2 Data negative (Top).
Connected to 88th Pin of Qseven MXM
Connector.
USB Host Port 2 Data Positive (Top).
Connected to 90th Pin of Qseven MXM
Connector.
USB Host Port 2 Ground (Top).
Shield Ground (Bottom).
Shield Ground USB2 (Top).
Rev 2.2
Page 40 of 168
Generic Qseven Carrier Board Hardware User Guide
2.5.3.2 USB 2.0 OTG Port
USB port1 OTG signals from Qseven MXM connector are connected to USB Micro AB connector (J28).
USB port1 supports OTG full functionality. By connecting proper USB Micro A Host cable or USB Micro B
Device cable, USB OTG full functionality can be supported. USB Micro AB connector is physically located
on the top of the board as shown below.
Figure 8: USB 2.0 OTG Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 41 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 9: USB 2.0 OTG Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/Termination
1
2
VBUS
D1-
Power
5V
Input/Output Differential
3
D1+
Input/Output Differential
4
ID
Input
3.3V CMOS
5
GND
Power
0V
Description
USB Port1 OTG, 5V Power.
USB Port1 OTG, Data negative.
Connected to 93rd Pin of Qseven
MXM Connector.
USB Port1 OTG, Data Positive.
Connected to 95th Pin of Qseven
MXM Connector.
USD Port1 OTG, ID signal.
Connected to 92nd Pin of Qseven
MXM Connector.
USB Port1 OTG Ground.
2.5.3.3 USB 2.0 Host Port4
USB2.0 Host Port4 signals from Qseven MXM connector are connected to USB Type-A connector (J4A)
and it is physically located on top of the board as shown below.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 42 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 9: USB 2.0 Connector
Table 10: USB 2.0 Host Port4 Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/Termination
1
2
VBUS
D-
Power
5V
Input/Output Differential
3
D+
Input/Output Differential
4
GND
Power
0V
iWave Systems Technologies Pvt. Ltd.
Description
USB 3.0 Port 2 VBUS power.
USB 2.0 Data Negative connected to
82nd pin of Qseven MXM connector
from USB2.0 Hub controller port4.
Optionally this pin is connected to
USB3.0 Hub controller port2 and
default not populated.
USB 2.0 Data Positive connected to
84th pin of Qseven MXM connector
from USB2.0 Hub controller port4.
Optionally this pin is connected to
USB3.0 Hub controller port2 and
default not populated.
Ground.
Rev 2.2
Page 43 of 168
Generic Qseven Carrier Board Hardware User Guide
2.5.4 CAN Port1
CAN Transmit and Receive signals from Qseven MXM connector Pin 129 and 130 respectively are
connected to CAN transceiver and the output signals from the transceiver are connected to DB9
connector (J26B). DB9 connector is physically located on top of the board as shown below.
Figure 10: CAN Port1 Connector
Table 11: CAN Port1 DB9 Connector Pin Out
Pin No
B1
B2
B3
B4
Pin Name
NC
CAN0L
GND
NC
Signal Type
NC
Input
Power
NC
Voltage Level/Termination
NC
Differential
0V
NC
iWave Systems Technologies Pvt. Ltd.
Description
No Connection.
CAN0 Differential negative.
Ground.
No Connection.
Rev 2.2
Page 44 of 168
M4
Generic Qseven Carrier Board Hardware User Guide
B5
B6
B7
CAN_SHLD_GND
GND
CAN0H
Power
Power
Input
0V
0V
Differential
CAN Shield Ground.
Ground.
CAN0 Differential positive.
B8
B9
NC
VCC_12V
NC
Power
NC
12V
No Connection.
12V Power supply.
2.6
High Speed Interface Features
2.6.1 SATA
2.6.1.1 SATA Port0
SATA port0 signals from Qseven MXM connector are connected to standard 22pin SATA connector with
power. This connector (J16) is physically located on top of the board as shown below.
Figure 11: SATA Port0 Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 45 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 12: SATA Port0 Connector Pin Out
Pin No
S1
S2
GND_S1
TXP0
Power
Output
Voltage Level/
Termination
0V
Differential
S3
TXN0
Output
Differential
SATA0 Transmit pair negative.
Connected to 31st Pin of Qseven
MXM Connector.
S4
S5
GND_S4
RXN0
Power
Input
0V
Differential
Ground.
SATA0 Receive pair negative.
Connected from 37th Pin of Qseven
MXM Connector.
S6
RXP0
Input
Differential
SATA0 Receive pair positive.
Connected from 35th Pin of Qseven
MXM Connector.
GND_S7
VCC_3.3V
VCC_3.3V
VCC_3.3V
GND
GND
GND
VCC_5V
VCC_5V
VCC_5V
GND
GND
GND
VCC_12V
VCC_12V
VCC_12V
SHLD
NC
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
NC
0V
3.3V
3.3V
3.3V
0V
0V
0V
5V
5V
5V
0V
0V
0V
12V
12V
12V
0V
NC
Ground.
3.3V Power Supply.
3.3V Power Supply.
3.3V Power Supply.
Ground.
Ground.
Ground.
5V Power Supply.
5V Power Supply.
5V Power Supply.
Ground.
Ground.
Ground.
12V Power Supply.
12V Power Supply.
12V Power Supply.
Shield Ground.
Mechanical Support.
S7
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
SH1,SH2
M1,M2
Pin Name
Signal Type
iWave Systems Technologies Pvt. Ltd.
Description
Ground
SATA0 Transmit pair positive.
Connected to 29th Pin of Qseven
MXM Connector.
Rev 2.2
Page 46 of 168
Generic Qseven Carrier Board Hardware User Guide
2.6.1.2 SATA Port1
SATA Port1 signals from Qseven MXM connector are connected to standard 7pin SATA connector
without power. This connector (J64) is physically located on bottom of the board as shown below.
Figure 12: SATA Port1 Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 47 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 13: SATA Port1 Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
GND
TXP1
Power
Output
Voltage Level/
Termination
0V
Differential
Description
3
TXN1
Output
Differential
SATA1 Transmit pair negative.
Connected from 32nd Pin of
Qseven MXM Connector.
4
5
GND
RXN1
Power
Input
0V
Differential
Ground
SATA1 Receive pair negative.
Connected to 38th Pin of
Qseven MXM Connector.
6
RXP1
Input
Differential
SATA1 Receive pair positive.
Connected to 36th Pin of
Qseven MXM Connector.
7
GND
Power
0V
Ground.
Ground
SATA1 Transmit pair positive.
Connected from 30th Pin of
Qseven MXM Connector.
2.6.2 PCI Express
2.6.2.1 PCIe x1 Connector
Qseven Generic Carrier Board supports PCIex1 connector. PCIe x1 signals are connected from Qseven
MXM Connector. PCIe x1 connector (J5) is physically located on top of the board for external access.
Note: Optionally PCIe Port1 signals are connected from PCIe switch downstream port2 to this PCIex1
connector through resistors and this option is not supported by default.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 48 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 13: PCIe x1 Connector
Table 14: PCIe x1 Connector Pin Out
Pin No
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
Pin Name
PRSNT1#
+12V
+12V
GND6
TCK
TDI
TDO
TMS
+3.3V
+3.3V
Signal Type
NC
Power
Power
Power
NC
NC
NC
NC
Power
Power
Voltage Level/
Termination
NC
12V
12V
0V
NC
NC
NC
NC
3.3V
3.3V
iWave Systems Technologies Pvt. Ltd.
Description
No Connection.
12V Power Supply.
12V Power Supply.
Ground.
No Connection.
No Connection.
No Connection.
No Connection.
3V Power Supply.
3V Power Supply.
Rev 2.2
Page 49 of 168
Generic Qseven Carrier Board Hardware User Guide
A11
PERST#
Output
3.3V CMOS
A12
A13
GND7
REFCLK+
Power
Output
0V
Differential
A14
REFCLK-
Output
Differential
A15
A16
GND8
PERp0
Power
Input
0V
Differential
A17
PERn0
Input
Differential
A18
B1
B2
B3
B4
B5
GND9
+12V
+12V
RSVD1
GND1
SMCLK
Power
Power
Power
NC
Power
Output
0V
12V
12V
NC
0V
3.3V CMOS
B6
SMDAT
Input/Output 3.3V CMOS
B7
GND2
Power
0V
iWave Systems Technologies Pvt. Ltd.
PCIe Reset.
Connected to 158th Pin of Qseven
MXM connector through buffer.
Ground.
PCIe reference clock positive.
Connected to 155th Pin of Qseven
MXM connector through Clock
buffer.
PCIe reference clock negative.
Connected to 157th Pin of Qseven
MXM connector through Clock
buffer.
Ground.
PCIe Receive Pair positive.
Connected to 180th Pin of Qseven
MXM connector.
Optionally connected to PCIe Switch
downstream Port2 through resistors
and default not populated.
PCIe Receive Pair negative.
Connected to 182nd Pin of Qseven
MXM connector.
Optionally connected to PCIe Switch
downstream Port2 through resistors
and default not populated.
Ground.
12V Power Supply.
12V Power Supply.
No Connection.
Ground.
System Management Bus Clock.
Connected to 60th Pin of Qseven
MXM Connector.
System Management Bus Data.
Connected to 62nd Pin of Qseven
MXM Connector.
Ground.
Rev 2.2
Page 50 of 168
Generic Qseven Carrier Board Hardware User Guide
B8
B9
B10
B11
+3.3V
TRST#
3V3AUX
WAKE#
Power
NC
Power
Input
3.3V
NC
3.3V
3.3V CMOS
3V Power Supply.
No Connection.
3V Always Power Supply.
PCIe interface wake up signal.
Connected to 156th Pin of Qseven
MXM Connector.
B12
B13
B14
RSVD2
GND3
PETp0+
NC
Power
Output
NC
0V
Differential
B15
PETn0
Output
Differential
No Connection.
Ground.
PCIe Transmit Pair positive
Connected to 179th Pin of Qseven
MXM Connector.
Optionally connected to PCIe Switch
downstream Port2 through resistors
and default not populated.
PCIe Transmit Pair negative.
Connected to 181st Pin of Qseven
MXM Connector.
Optionally connected to PCIe Switch
downstream Port2 through resistors
and default not populated.
GND4
PRSNT2#
GND5
Mechanical
Support
Power
NC
Power
Mechanical
Support
0V
NC
0V
Mechanical
Support
B16
B17
B18
M1,M2
iWave Systems Technologies Pvt. Ltd.
Ground.
No Connection.
Ground.
Mechanical Support.
Rev 2.2
Page 51 of 168
Generic Qseven Carrier Board Hardware User Guide
2.6.2.2 PCIe Port 2 Header (Optional)
PCIe port 2 signals from the Qseven MXM Connector are connected to an 18 pin SMD pad header (J49)
for add-on purpose. These SMD pads can be accessed at the bottom of the board as shown below, by
default it is not populated in the design.
Figure 14: PCIe Port2 Header
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 52 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 15: PCIe Port2 Header Pin Out
Pin No
1
2
3
VCC_12V
VCC_3V3
PCIE2_TX+
Power
Power
Output
Voltage Level/
Termination
12V
3.3V
Differential
4
5
VCC_3V3
PCIE2_TX-
Power
Output
3.3V
Differential
6
PCIE2_RX+
Input
Differential
7
8
GND
PCIE2_RX-
Power
Input
0V
Differential
9
PCIE4_CLK-
Output
Differential
10
11
GND
PCIE4_CLK+
Power
Output
0V
Differential
12
PCIE2_RST#
Output
3.3V CMOS
GND
PCIECLK_OE4#
VCC_3V3
SMB_DAT
Power
Input
Power
Input/ Output
0V
3.3V CMOS
3.3V
3.3V CMOS
SMB_CLK
Input
3.3V CMOS
13,14
15
16
17
18
Pin Name
Signal Type
iWave Systems Technologies Pvt. Ltd.
Description
Supply Voltage 12V.
Supply Voltage 3.3V.
PCIe2 transmit pair positive.
Connected to 167th Pin of Qseven MXM
Connector.
Supply Voltage 3.3V.
PCIe2 transmit pair negative.
Connected to 169th Pin of Qseven MXM
Connector.
PCIe2 receive pair positive. Connected
from 168th Pin of Qseven MXM
Connector.
Ground.
PCIe2 differential receive line negative.
Connected from 170th Pin of Qseven
MXM Connector.
PCIe4 reference clock pair negative.
Connected to 157th Pin of Qseven MXM
connector through Clock buffer.
Ground.
PCIe4 reference clock pair positive.
Connected to 155th Pin of Qseven MXM
connector through Clock buffer.
PCIe2 Reset.
Connected to 158th Pin of Qseven MXM
connector through buffer.
Ground.
PCIe clock request.
Supply Voltage 3.3V.
System Management Bus Data.
Connected to 62nd Pin of Qseven MXM
Connector.
System Management Bus Clock.
Connected to 60th Pin of Qseven MXM
Connector.
Rev 2.2
Page 53 of 168
Generic Qseven Carrier Board Hardware User Guide
2.6.2.3 PCIe Port 3 Header (Optional)
PCIe port 3 signals from the Qseven MXM Connector are connected to an 18 pin header (J44) for add-on
purpose. These SMD pads can be accessed at the bottom of the board as shown below, by default it is
not populated in the design.
Figure 15: PCIe Port3 Header
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 54 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 16: PCIe Port3 Header Pin Out
Pin No
1
2
3
VCC_12V
VCC_3V3
PCIE3_TX+
Power
Power
Output
Voltage Level/
Termination
12V
3.3V
Differential
4
5
VCC_3V3
PCIE3_TX-
Power
Output
3.3V
Differential
6
PCIE3_RX+
Input
Differential
7
8
GND
PCIE3_RX-
Power
Input
0V
Differential
9
PCIE5_CLK-
Output
Differential
10
11
GND
PCIE5_CLK+
Power
Output
0V
Differential
Ground.
PCIe5 reference clock pair positive.
Connected to 155th Pin of Qseven
MXM Connector through Clock buffer.
PCIE2_RST#
GND
PCIECLK_OE5#
VCC_3V3
SMB_DAT
Output
Power
Input
Power
Input/Output
3.3V CMOS
0V
3.3V CMOS
3.3V
3.3V CMOS
SMB_CLK
Input
3.3V CMOS
PCIe2 Reset.
Ground.
Connected to 158th Pin of Qseven
PCIe
request.
MXMclock
Connector
through buffer.
Supply Voltage 3.3V.
System Management Bus Data.
Connected to 62nd Pin of Qseven MXM
Connector.
System Management Bus Clock.
Connected to 60th Pin of Qseven MXM
Connector.
12
13,14
15
16
17
18
Pin Name
Signal Type
iWave Systems Technologies Pvt. Ltd.
Description
Supply Voltage 12V.
Supply Voltage 3.3V.
PCIe3 transmit pair positive.
Connected to 161st Pin of Qseven
MXM Connector.
Supply Voltage 3.3V.
PCIe3 transmit pair negative.
Connected to 163rd Pin of Qseven
MXM Connector.
PCIe3 receive pair positive.
Connected from 162nd Pin of Qseven
MXM Connector.
Ground.
PCIe3 receive pair negative.
Connected from 164th Pin of Qseven
MXM Connector.
PCIe5 reference clock pair negative.
Connected to 157th Pin of Qseven
MXM Connector through Clock buffer.
Rev 2.2
Page 55 of 168
Generic Qseven Carrier Board Hardware User Guide
2.6.2.4 PCIe Switch
Qseven Generic Carrier Board supports on board 4-Port Gen2.0 PCI Express Switch. This PCIe Switch
supports 1 upstream port and 3 downstream ports. The upstream port (PCIe switch Port0) of the PCIe
switch is connected to PCIe port0 interface of Qseven MXM connector. The three downstream PCIe
ports of the PCIe switch are connected respectively to,

Mini PCIe Connector

PCIe to USB 3.0 Hub controller
By default 4-Port PCIe switch and USB 3.0 controller are not populated.
2.6.2.4.1 Mini PCIe Connector
Qseven Generic Carrier Board supports Mini PCIe connector with PCIe interface from PCIe switch
downstream port1 and USB Host3 interface from Qseven MXM connector. Since PCIe switch is not
populated Mini PCIe connector and SIM slot cannot be used. Mini PCIe connector (J52) and SIM
connector (J40) are physically located at bottom of the board as shown below.
Figure 16: Mini PCIe Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 56 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 17: Mini PCIe Connector Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/
Termination
1
WAKE#
Input
3.3V CMOS
2
3
4
5
6
+3.3V_AUX
COEX1
GND
COEX2
1.5V
Power
NC
Power
NC
Power
3.3V
NC
0V
NC
1.5V
7
8
CLKREQ#
UIM_PWR
Input
Power
3.3V CMOS
3V
9
10
GND1
UIM_DATA
Power
Input/Output
0V
3V
11
REFCLK-
Output
Differential
12
UIM_CLK
Input
3V CMOS
13
REFCLK+
Output
Differential
14
UIM_RESET
Input
3V CMOS
15
16
17
18
GND2
UIM_VPP
RSVD(UIM_C8)
GND3
Power
NC
NC
Power
0V
NC
NC
0V
iWave Systems Technologies Pvt. Ltd.
Description
PCIe interface Wake Up Signal.
Connected to 156th Pin of Qseven
MXM Connector.
3.3V Power Supply.
No Connection.
Ground.
No Connection.
Optional 3G supply.
Default NC.
Clock Request
SIM Supply.
Connected to 1st pin of SIM
connector (J40).
Ground.
SIM Data.
Connected to 6th pin of SIM
connector (J40).
PCIe1 reference clock negative.
Connected to 157th Pin of Qseven
MXM connector through Clock
buffer
SIM
Clock.
.
Connected to 3rd pin of SIM
connector (J40).
PCIe1 reference clock positive.
Connected to 155th Pin of Qseven
MXM connector through Clock
buffer.
SIM Reset.
Connected to 2nd pin of SIM
connector (J40).
Ground.
No Connection.
No Connection.
Ground.
Rev 2.2
Page 57 of 168
Generic Qseven Carrier Board Hardware User Guide
19
20
RSVD(UIM_C84
W_DISABLE#
NC
Output
NC
3.3V CMOS
21
22
GND4
PERST#
Power
Output
0V
3.3V CMOS
23
PERn0
Input
Differential
24
25
+3.3V_AUX
PERp0
Power
Input
3.3V
Differential
26
27
28
GND5
GND6
1.5V
Power
Power
Power
0V
0V
1.5V
29
30
GND7
SMB_CLK
Power
Output
0V
3.3V CMOS
31
PETn0
Output
Differential
32
SMB_DATA
Input/Output
3.3V CMOS
33
PETp0
Output
Differential
34
35
36
GND8
GND9
USB_D-
Power
Power
Input/Output
0V
0V
Differential
37
GND10
Power
0V
iWave Systems Technologies Pvt. Ltd.
No Connection.
Wireless Disable.
Connected to 24th Pin of Expansion
Connector1.
Ground.
PCIe1 Reset.
Connected to 158th Pin of Qseven
MXM connector through buffer.
PCIe Receive Pair Negative.
Connected to PCIe Switch
downstream Port1.
3.3V Power Supply.
PCIe Receive Pair positive.
Connected to PCIe Switch
downstream Port1.
Ground.
Ground.
Optional 3G supply.
Default NC.
Ground.
System Management Bus Clock.
Connected to 60th Pin of Qseven
MXM Connector.
PCIe Transmit Pair negative
Connected to PCIe Switch
downstream Port1.
System Management Data.
Connected to 62nd Pin of Qseven
MXM Connector.
PCIe Transmit Pair Positive
Connected to PCIe Switch
downstream Port1.
Ground.
Ground.
USB Host Port3 Data negative.
Connected to 87th Pin of in Qseven
MXM Connector.
Ground.
Rev 2.2
Page 58 of 168
Generic Qseven Carrier Board Hardware User Guide
38
USB_D+
Input/Output
Differential
39
40
41
42
+3.3V_AUX
GND11
+3.3V_AUX
LED_WWAN#
Power
Power
Power
Input
3.3V
0V
3.3V
3.3V CMOS
43
44
GND12
LED_WLAN#
Power
Input
0V
3.3V CMOS
45
RSVD
Input
3.3V CMOS
Default NC.
Connected to 45th Pin of Expansion
Connector2 through resistor and
default not populated.
46
LED_WPAN#
Input
3.3V CMOS
LED Enable.
Connected to red LED D19 and
default not populated.
47
RSVD1
Input
3.3V CMOS
Default NC.
Connected to 44th Pin of Expansion
Connector2 through resistor and
default not populated
48
1.5V
Power
1.5V
49
RSVD2
Output
3.3V CMOS
50
51
GND13
RSVD3
Power
Input
0V
3.3V CMOS
52
+3.3V_AUX
Power
3.3V
Optional 3G supply.
Default NC.
Default NC.
Connected to 41st Pin of Expansion
Connector2 through resistor and
default not populated
Ground
Default NC.
Connected to 43rd Pin of Expansion
Connector2 through resistor and
default not populated
3.3V Power Supply.
iWave Systems Technologies Pvt. Ltd.
USB Host Port3 Data positive.
Connected to 89th Pin of Qseven
MXM Connector.
3.3V Power Supply.
Ground.
3.3V Power Supply.
LED Enable.
Connected to red LED D22 and
default populated.
Ground.
LED Enable.
Connected to red LED D21 and
default not populated.
Rev 2.2
Page 59 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 18: SIM Connector Pin Out
Pin No
1
2
3
4
5
6
Pin Name
VCC
RST
CLK
GND
VPP
IO
Signal Type
Power
Input
Input
Power
Power
Input
Voltage Level/
Termination
3V
3V CMOS
3V CMOS
0V
3V
3V
Description
SIM Power Supply from Mini PCIe.
SIM Reset from Mini PCIe.
SIM Clock from Mini PCIe.
Ground.
SIM VPP Power from Mini PCIe.
SIM IO Data from Mini PCIe.
2.6.2.4.2 PCIe to USB 3.0 Controller
Qseven Generic Carrier Board supports on board PCIe to USB 3.0 controller to support USB 3.0 Host
port. PCIe switch downstream port3 signals are connected to USB 3.0 controller. By default 4-Port PCIe
switch and USB 3.0 controller are not populated and USB 3.0 dual stack connector is not populated and
instead a single Type A USB 2.0 port is populated in the design, refer Figure 9 to identify the location of
the connector.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 60 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7
Audio/ Video Features
2.7.1 Audio In/Out
Four wire AC’97 signals from the Qseven MXM Connector are connected to AC’97 Audio Codec. The
Audio CODEC used on the Qseven Generic Carrier Board is ALC5610 from Realtek with inbuilt
Headphone amplifier & MIC which is used to provide a complete audio solution for portable products.
Qseven Generic Carrier Board supports 3.5mm Audio out Stereo Jack (J24) and 3.5mm Audio In Mono
Jack (J23) which are physically located on top of the board as shown below.
Figure 17: Audio Jack
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 61 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 19: Audio OUT Jack Pin Out
Pin No
Pin Name
Signal Type
Voltage Level/ Termination
1
2
3
4
GND
HP_L
HP_R
HP_DETECT
Power
Output
Output
Output
0V
3.3V Analog
3.3V Analog
3.3V Analog
5
NC
NC
NC
Description
Ground.
Headphone Left.
Headphone Right.
Head Phone Detection.
Connected from 38th Pin of
Expansion Connector1.
No Connection.
Table 20: Audio IN Jack Pin Out
Pin No
1
2
3
4
5
Pin Name
GND
MIC1P
NC
MIC_IN_DETECT
Signal Type
Power
Input
NC
Input
Voltage Level/ Termination
0V
3.3V Analog
NC
3.3V CMOS
MIC_INT
Input
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
Ground
Microphone Signal
No Connection
Microphone Detection.
Connected from 31st Pin of
Expansion Connector1.
Internal MIC connection.
Rev 2.2
Page 62 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7.2 LVDS Display Interface
The Qseven Generic Carrier Board supports different displays through LVDS0 & LVDS1 interface from
Qseven MXM connector. LVDS0 interface from Qseven MXM connector is connected to LVDS0 LCD
connector and also on-board LVDS transmitter. This LVDS transmitter converts LVDS0 interface signals to
RGB and connects to 7” RGB Resistive touch LCD or 7” RGB Capacitive touch LCD.LVDS1 interface from
Qseven MXM connector is connected to LVDS1 LCD connector.
Note: Either LVDS0 connector or 7” RGB resistive touch LCD or 7” RGB capacitive touch LCD only can be
used at a time
2.7.2.1 LVDS0 Connector
Qseven Generic Carrier Board supports LVDS0 connector to connect different LVDS LCDs. It also
supports backlight connector with 15V 300mA output for LCD backlight. LVDS0 connector (J7) is
physically located on top of the board & Backlight connector (J33) at the bottom of the board as shown
below.
LVDS0 LCD Connector:
Number of Pins: 20
LVDS LCD Connector Part number: DF19G-20P-1H(54)
Backlight Connector:
Number of Pins: 2
Backlight Connector Part Number: SM02B-BHSS-1-TB
Mating Connector: SM02B-BHSS-1-TB from JST Sales America Inc
Compatible LCDs
1. Part Number: OSD104T0571-19TS
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: OSD Displays
2. Part Number: T-51944D104J-FW-A-ABN
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: OPTREX Corporation
3. Part Number: TLM-TA40T3130-01
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: Varitronix
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 63 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 18: LVDS0 Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 64 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 21: LVDS0 Connector Pin Out
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin Name
VDD1
VDD2
GND1
GND2
RIN0-
RIN0+
GND3
RIN1-
RIN1+
GND4
RIN2-
RIN2+
GND5
Signal Type
Power
Power
Power
Power
Output
Output
Power
Output
Output
Power
Output
Output
Power
Voltage Level/
Termination
3.3V
3.3V
0V
0V
LVDS
LVDS
0V
LVDS
LVDS
0V
LVDS
LVDS
0V
iWave Systems Technologies Pvt. Ltd.
Description
Supply voltage for TFT.
Supply voltage for TFT.
Ground.
Ground.
LVDS primary channel
pair0 negative.
Connected to 101st Pin
MXM Connector.
LVDS primary channel
pair0 positive.
Connected to 99th Pin
MXM Connector.
Ground.
LVDS primary channel
pair1 negative.
Connected to 105th Pin
MXM Connector.
LVDS primary channel
pair1 positive.
Connected to 103rd Pin
MXM Connector.
Ground.
LVDS primary channel
pair2 negative.
Connected to 109th Pin
MXM Connector.
LVDS primary channel
pair2 positive.
Connected to 107th Pin
MXM Connector.
Ground.
differential
of Qseven
differential
of Qseven
differential
of Qseven
differential
of Qseven
differential
of Qseven
differential
of Qseven
Rev 2.2
Page 65 of 168
Generic Qseven Carrier Board Hardware User Guide
14
15
16
17
18
19
20
CLKIN-
CLKIN+
GND6
RIN3-
RIN3+
GND7
GND8
Output
Output
Power
Output
Output
Power
Power
LVDS
LVDS
0V
LVDS
LVDS
0V
0V
LVDS primary channel
clock negative.
Connected to 121st Pin
MXM Connector.
LVDS primary channel
clock positive.
Connected to 119th Pin
MXM Connector.
Ground.
LVDS primary channel
pair3 negative.
Connected to 115th Pin
MXM Connector.
LVDS primary channel
pair3 positive.
Connected to 113th Pin
MXM Connector.
Ground.
Ground.
differential
of Qseven
differential
of Qseven
differential
of Qseven
differential
of Qseven
Table 22: LVDS0 Backlight Connector Pin Out
Pin No
1
2
Pin Name
LED_A0
LED_K0
Signal Type
Power
Power
Voltage Level/
Termination
15V
0V
Description
LED Anode.
LED Cathode.
Note: To change the LVDS0 Backlight LED driver setting,
1. Change Current sensing resistor R24 (RSET) by calculating using the below formula
Where VFB = 190mV, ILED = Current required for LCD backlight LEDs.
2. Change D14 Zener Diode from 15V to required voltage.
(Populated diode part number is BZT52C20-7-F)
Note: Refer APPENDIX I for Silkscreen identifier details
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 66 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7.2.2 7” RGB Resistive Touch LCD (optional)
The Qseven Generic Carrier Board supports 7’’ RGB LCD with resistive touch interface. LVDS0 interface
from Qseven MXM connector is connected to LVDS transmitter and output of transmitter is connected
to 7” RGB Resistive Touch LCD connector and 7” RGB Capacitive Touch LCD connector. Either one can be
used at a time.7” RGB Resistive touch LCD supports 800x480 resolution with 18BPP depth. 7” RGB
Resistive LCD connector (J43) and touch connector (J50) are physically located at the bottom of board as
shown below.
LCD Connector:
Number of Pins: 40
LCD Connector Part number: FH12A-40S-0.5SH(55)
Touch Panel Connector:
Number of Pins: 4
Touch Connector Part number: SFW4R-3STE1LF
Compatible LCD:
Part Number: KWH070KQ13-F02
Description: 7 inch, LCD 18 bit with 800 x 480 (RGB) resolution
Manufacturer Name: Formike Electronic Co.Ltd
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 67 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 19: 7`` Resistive LCD Connector
Table 23: 7`` RGB Resistive LCD Connector Pin Out
Pin
No
Pin Name
Signal Type
Voltage Level/
Termination
1
2
3
VLED1
VLED2
ADJ
Power
Power
Output
5V
5V
3.3V CMOS
4
GLED1
Power
0V
iWave Systems Technologies Pvt. Ltd.
Description
Power Voltage for LED Driver.
Power Voltage for LED Driver.
LVDS Panel backlight brightness
control.
Connected to 123rd Pin of Qseven MXM
Connector.
Ground.
Rev 2.2
Page 68 of 168
Generic Qseven Carrier Board Hardware User Guide
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GLED2
VCC1
VCC2
MODE
DE
VS
HS
GND1
B5
B4
B3
GND2
B2
B1
B0
GND3
G5
G4
G3
GND4
G2
G1
G0
GND5
R5
R4
R3
GND6
R2
R1
R0
GND7
DCLK
GND8
L/R
U/D
Power
Power
Power
Output
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Input
Input
Input
Power
Output
Output
Output
Power
Output
Power
Output
Output
0V
3.3V
3.3V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Ground.
Supply voltage for TFT.
Supply voltage for TFT.
DE or HV mode control.
Display Enable.
Display VSYNC signal input.
Display HSYNC signal input.
Ground.
Display Blue Data 7 (MSB).
Display Blue Data 6.
Display Blue Data 5.
Ground.
Display Blue Data 4.
Display Blue Data 3.
Display Blue Data 2 (LSB+2).
Ground.
Display Green Data 7 (MSB).
Display Green Data 6.
Display Green Data 5.
Ground.
Display Green Data 4.
Display Green Data 3.
Display Green Data 2 (LSB+2).
Ground.
Display Red Data 7 (MSB).
Display Red Data 6.
Display Red Data 5.
Ground.
Display Red Data 4.
Display Red Data 3.
Display Red Data 2 (LSB+2).
Ground.
Display Clock.
Ground.
Left or Right Scanning Direction.
Up or Down Scanning Direction.
Rev 2.2
Page 69 of 168
Generic Qseven Carrier Board Hardware User Guide
Qseven Generic Carrier Board supports on board Resistive Touch Controller MAX11801ETC+ (from
Maxim Integrated) to support touch interface. This touch controller is connected to I2C interface of
Qseven MXM connector (66th and 68th Pin).
Table 24: Resistive Touch Connector Pin Out
Pin
Pin Name
Signal Type Voltage Level/
Description
No
Termination
1
Y1
Input
Analog
Touch Left Signals.
2
X2
Input
Analog
Touch Up Signals.
3
Y2
Input
Analog
Touch Right Signals.
4
X1
Input
Analog
Touch Down Signals.
Note: Optionally these touch signals are directly connected to Expansion Connector-2 (J9) through
resistor and default not populated.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 70 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7.2.3 Capacitive Touch LCD Interface
The Qseven Generic Carrier Board also supports 7’’ RGB LCD with capacitive touch interface. LVDS0
interface from Qseven MXM connector is connected to LVDS transmitter and output of transmitter is
connected to 7” RGB Resistive Touch LCD and 7” RGB Capacitive Touch LCD. Either one can be used at a
time.7” RGB capacitive LCD (J8) and touch connector (J13) are physically located on bottom of board.
The backlight connector (J54) with voltage 10V 160mA is physically located at the bottom of the board
as shown below.
LCD Connector:
Number of Pins: 40
LCD Connector Part number: FH12A-40S-0.5SH(55)
Backlight Connector:
Number of Pins: 2
Backlight Connector Part Number: SM02B-BHSS-1-TB(LF)(SN)
Mating Connector: BHSR-02VS-1 from JST Sales America Inc
Touch Panel Connector:
Number of Pins: 10
Touch Connector Part number: 52746-1071
Compatible LCD:
Part Number: ETM070001ADH6
Description: 7 inch, LCD 18 bit with 800 x 480 (RGB) resolution
Manufacturer Name: Emerging Display Technologies Corporation
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 71 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 20: 7`` Capacitive Touch LCD Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 72 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 25: 7`` Capacitive Touch LCD Connector Pin Out
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Pin Name
U/D
R/L
NC1
VCC1
VCC2
VCC3
VCC4
NC2
DE
VSS1
VSS2
VSS3
B5
B4
B3
VSS4
B2
B1
B0
VSS5
G5
G4
G3
VSS6
G2
G1
G0
VSS7
R5
R4
R3
VSS8
R2
R1
Signal Type
Output
Output
NC
Power
Power
Power
Power
NC
Output
Power
Power
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Output
Power
Output
Output
Voltage Level/
Termination
3.3V CMOS
3.3V CMOS
NC
3.3V
3.3V
3.3V
3.3V
NC
3.3V CMOS
0V
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
Up or Down Scanning Direction.
Left or Right Scanning Direction.
No Connection.
Supply voltage for TFT.
Supply voltage for TFT.
Supply voltage for TFT.
Supply voltage for TFT.
No Connection.
Display Enable.
Ground.
Ground.
Ground.
Display Blue Data Input 7.
Display Blue Data Input 6.
Display Blue Data Input 5.
Ground.
Display Blue Data Input 4.
Display Blue Data Input 3.
Display Blue Data Input 2.
Ground.
Display Green Data Input 7.
Display Green Data Input 6.
Display Green Data Input 5.
Ground.
Display Green Data Input 4.
Display Green Data Input 3.
Display Green Data Input 2.
Ground.
Display Red Data Input 7.
Display Red Data Input 6.
Display Red Data Input 5.
Ground.
Display Red Data Input 4.
Display Red Data Input 3.
Rev 2.2
Page 73 of 168
Generic Qseven Carrier Board Hardware User Guide
35
36
37
38
39
40
R0
VSS9
NC3
DCLK
HSYNC
VSYNC
Output
Power
NC
Output
Output
Output
3.3V CMOS
0V
NC
3.3V CMOS
3.3V CMOS
3.3V CMOS
Display Red Data Input 2.
Ground.
No Connection.
Display Clock.
Display HSYNC signal input.
Display VSYNC signal input.
Table 26: Capacitive touch Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
3
VSS1
VDD
SCL
Power
Power
Output
Voltage Level/
Termination
0V
3.3V
3.3V CMOS
4
5
NC1
SDA
NC
Input/Output
NC
3.3V CMOS
6
7
8
NC2
RST#
WAKE#
NC
Input
Output
NC
3.3V CMOS
3.3V CMOS
9
INT#
Input
3.3V CMOS
10
VSS1
Power
0V
Description
Ground.
Supply voltage for TFT.
I2C Clock.
Connected to 66th Pin of
Qseven MXM Connector.
No Connection.
I2C Data.
Connected to 68th Pin of
Qseven MXM Connector.
No Connection.
Reset.
Wake Interrupt.
Connected to 17th Pin of
Qseven MXM Connector.
Touch Interrupt.
Connected to 41st Pin of
Expansion Connector1.
Ground.
Table 27: Backlight LED Pin Out
Pin No
1
2
Pin Name
VBL+(A)
VBL-(K)
Signal Type
Power
Power
Voltage Level/
Termination
9.9V
0V
iWave Systems Technologies Pvt. Ltd.
Description
LED Anode.
LED Cathode.
Rev 2.2
Page 74 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7.2.4 LVDS1 Connector
Qseven Generic Carrier Board supports LVDS1 connector to connect different LVDS LCDs. It also
supports backlight connector with 15V 300mA output for LCD backlight. LVDS1 connector (J58) and
backlight connector (J57) are physically located at the bottom of the board as shown below.
LVDS1 LCD Connector:
Number of Pins: 20
LVDS LCD Connector Part number: DF19G-20P-1H(54)
Backlight Connector:
Number of Pins: 2
Backlight Connector Part Number: GRPB021VWVN-RC
Mating Connector: LPPB021NFFN-RC from Sullins Connector Solutions
Compatible LCDs
1. Part Number: OSD104T0571-19TS
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: OSD Displays
2. Part Number: T-51944D104J-FW-A-ABN
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: OPTREX Corporation
3. Part Number: TLM-TA40T3130-01
Description: 10.4 inch LVDS 6 bits with 800 x 600 (RGB) resolution
Manufacturer Name: Varitronix
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 75 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 21: LVDS1 Connectors
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 76 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 28: LVDS1 Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
3
4
5
VDD1
VDD2
GND1
GND2
RIN0-
Power
Power
Power
Power
Input
Voltage Level/
Termination
3.3V
3.3V
0V
0V
LVDS
Description
6
RIN0+
Input
LVDS
7
8
GND3
RIN1-
Power
Input
0V
LVDS
9
RIN1+
Input
LVDS
10
11
GND4
RIN2-
Power
Input
0V
LVDS
12
RIN2+
Input
LVDS
13
GND5
Power
0V
LVDS
secondary
channel
differential pair0 positive.
Connected to 100th Pin of Qseven
MXM Connector.
Ground.
LVDS
secondary
channel
differential pair1 negative.
Connected to 106th Pin of Qseven
MXM Connector.
LVDS
secondary
channel
differential pair1 positive.
Connected to 104th Pin of Qseven
MXM Connector.
Ground.
LVDS
secondary
channel
differential pair2 negative.
Connected to 110th Pin of Qseven
MXM Connector.
LVDS
secondary
channel
differential pair2 positive.
Connected to 108th Pin of Qseven
MXM Connector.
Ground.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 77 of 168
Supply voltage for TFT.
Supply voltage for TFT.
Ground.
Ground.
LVDS
secondary
channel
differential pair0 negative.
Connected to 102nd Pin of Qseven
MXM Connector.
Generic Qseven Carrier Board Hardware User Guide
14
CLKIN-
Input
LVDS
LVDS
secondary
channel
differential clock negative.
Connected to 122nd Pin of Qseven
MXM Connector.
15
CLKIN+
Input
LVDS
16
17
GND6
RIN3-
Power
Input
0V
LVDS
18
RIN3+
Input
LVDS
19
20
GND7
GND8
Power
Power
0V
0V
LVDS
secondary
channel
differential clock positive.
Connected to 120th Pin of Qseven
MXM Connector.
Ground
LVDS
secondary
channel
differential pair3 negative.
Connected to 116th Pin of Qseven
MXM Connector.
LVDS
secondary
channel
differential pair3 positive.
Connected to 114th Pin of Qseven
MXM Connector.
Ground.
Ground.
Table 29: LVDS1 Backlight Connector Pin Out
Pin No
1
2
Pin Name
LED_A1
LED_K1
Signal Type
Power
Power
Voltage Level/
Termination
15V
0V
Description
LED Anode.
LED Cathode.
Note: To change theLVDS1 Backlight LED driver setting,
1. Change Current sensing resistor R361 (RSET) by calculating using the below formula
Where VFB = 190mV, ILED = Current required for LCD backlight LEDs.
2. Change D24 Zener Diode from 15V to required voltage.
(Populated diode part number is BZT52C20-7-F)
Note: Refer APPENDIX I for Silkscreen identifier details
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 78 of 168
Generic Qseven Carrier Board Hardware User Guide
2.7.3 HDMI Interface
Qseven Generic Carrier Board supports HDMI port to support bigger monitor. TMDS signals from Qseven
MXM connector are connected to Standard HDMI port with ESD protection circuitry. HDMI connector
(J27) is physically located on top of the board as shown below.
Figure 22: HDMI Port
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 79 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 30: HDMI Port Pin Out
Pin No
Pin Name
Signal Type
1
D2+
Output
Voltage Level/
Termination
TMDS
2
3
D2_GND
D2-
Power
Output
0V
TMDS
Red Pair Ground.
HDMI data2 pair negative.
Connected to 151th Pin of
Qseven MXM Connector.
4
D1+
Output
TMDS
HDMI data1 pair positive.
Connected to 137th Pin of
Qseven MXM Connector.
5
6
D1_GND
D1-
Power
Output
0V
TMDS
Green Pair Ground.
HDMI data1 pair positive.
Connected to 139th Pin of
Qseven MXM Connector
7
D0+
Output
TMDS
HDMI data0 pair positive.
Connected to 143rd Pin of
Qseven MXM Connector.
8
9
D0_GND
D0-
Power
Output
0V
TMDS
Blue Pair Ground.
HDMI data0 pair positive.
Connected to 145th Pin of
Qseven MXM Connector.
10
CLK+
Output
TMDS
Display Clock pair positive.
Connected to 131st Pin of Qseven
MXM Connector.
11
12
CLK_GND
CLK-
Power
Output
0V
TMDS
Clock pair Ground.
Display Clock pair negative.
Connected to 133rd Pin of
Qseven MXM Connector.
13
CEC
Input/Output 3.3V CMOS
14
RSV/NC
NC
NC
iWave Systems Technologies Pvt. Ltd.
Description
HDMI data2 pair positive.
Connected to 149th Pin of
Qseven MXM Connector.
Consumer Electronic Control.
Connected to 124th Pin of
Qseven MXM Connector.
No Connection.
Rev 2.2
Page 80 of 168
Generic Qseven Carrier Board Hardware User Guide
15
SCL
Output
16
SDA
Input/Output 3.3V CMOS
17
18
19
DDC/CEC_GND
+5V
HPD
Power
Power
Input
0V
5V
3.3V CMOS
Mechanical
support
Mechanical
support
M1,M2, Mechanical support
M3,M4
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
EDID I2C Clock.
Connected to 152nd Pin of
Qseven MXM Connector.
EDID I2C Data.
Connected to 150th Pin of
Qseven MXM Connector.
Ground.
5V Power Supply.
HDMI Cable Hot plug detect.
Connected from 153rd Pin of
Qseven MXM Connector.
Mechanical support.
Rev 2.2
Page 81 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8
Additional Features
2.8.1 JTAG Connector
Qseven Generic Carrier Board supports 10-pin JTAG connector for debug purpose. Since both UART and
JTAG share the same pins of Qseven MXM connector, a jumper option (J37) is provided to select either
one. This Jumper is connected to 204th Pin of Qseven MXM connector. If the Jumper is open UART is
selected as Debug port and if closed JTAG is selected as Debug port. For further information on these
signals refer section “Manufacturing Signals” of Qseven-Spec_2.0. JTAG connector (J32) is physically
located at the bottom of the board as shown below.
Number of Pins: 10
Connector Part number: GRPB052VWVN-RC
Mating Connector: LPPB052CFFN-RC from Sullins Connector Solutions
Figure 23: JTAG Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 82 of 168
Generic Qseven Carrier Board Hardware User Guide
Note: To support this dynamic selection, Qseven module which is connected to this Generic carrier board
also should support dynamic selection. By default jumper is open and UART is selected as Debug port.
Table 31: JTAG Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
3
4
VCC_3V3
GND
VCC_3V3
MFG4_JTAG_TRST#
Power
Power
Power
Input
Voltage Level/
Termination
3V
0V
3V
3.3V CMOS
5
MFG0_JTAG_TCK
Input
3.3V CMOS
6
MFG2_JTAG_TDI
Input
3.3V CMOS
7
MFG1_JATG_TDO
Output
3.3V CMOS
8
MFG3_JTAG_TMS
Input
3.3V CMOS
9
10
GND
GND
Power
Power
0V
0V
iWave Systems Technologies Pvt. Ltd.
Description
Supply Voltage.
Ground.
Supply Voltage.
JTAG Reset.
Connected from 204th Pin of
Qseven MXM Connector.
JTAG Test Clock.
Connected from 207th Pin of
Qseven MXM Connector.
JTAG Test Data Input.
Connected from 208th Pin of
Qseven MXM Connector.
JTAG Test Data Output.
Connected to 209th Pin of
Qseven MXM Connector.
JTAG Test Mode Select.
Connected from 210th Pin of
Qseven MXM Connector.
Ground.
Ground.
Rev 2.2
Page 83 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.2 RTC Battery
The Qseven Generic Carrier Board supports on board RTC battery holder to connect 3V backup coin cell.
This coin cell battery is connected to 193rd pin of Qseven MXM connector. This battery holder (J42) is
physically located at the bottom of the board as shown below.
Number of Pins: 2
Connector Part number: ML-2020/V1AN
Compatible RTC Battery: CR2032 from Maxell
Figure 24: RTC Battery
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 84 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.3 Control Buttons
2.8.3.1 Power Button
The Qseven Generic Carrier Board supports on board Power push button to power on/off the Qseven
SOM module. This power button (S1) is physically located at the top of the board as shown below and
connected to 20th Pin of Qseven MXM Connector.
Figure 25: Power Button
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 85 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.3.2 Reset Button
The Qseven Generic Carrier Board supports on board Reset push button to reset the Qseven SOM
module. This reset button (S2) is physically located at the top of the board as shown below and
connected to 28th Pin of Qseven MXM Connector.
Figure 26: Reset Button
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 86 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.3.3 Tamper Switch (Optional)
The Qseven Generic Carrier Board supports on board Tamper Switch (S3). This switch is connected to
154th Pin of Qseven MXM connector through resistor and default not populated. This switch (S3) is
physically located on the top of the board as shown below and not populated.
Figure 27: Tamper Switch
Note: This is not the standard feature of Qseven specification.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 87 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.4 EEPROM (Optional)
The Qseven Generic Carrier Board supports on board EEPROM, this EEPROM is connected to I2C
interface of Qseven MXM Connector (66th and 68th Pin) and it is physically located at the bottom of the
board as shown below and not populated.
Figure 28: EEPROM
Note: This is not the standard feature of Qseven specification.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 88 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.5 Sensors
The Qseven Generic Carrier Board supports 4 on board sensors,

Ambient Light Sensor

Digital eCompass

3-Axis accelerometer

Altimeter/Barometer
Below figure shows the Sensor’s physical location on the top and bottom of the board as shown below.
Figure 29: Sensors
2.8.5.1 Ambient Light Sensor
The Qseven Generic Carrier Board supports on board Ambient Light Sensor. This sensor is connected to
I2C interface of Qseven MXM connector (66th and 68th Pin) and interrupt is connected to 188th Pin of
Qseven MXM connector. This sensor (U33) is physically located on the top of the board as shown in
Figure 29
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 89 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.5.2 Digital eCompass
The Qseven Generic Carrier Board supports on board Digital eCompass Sensor. This sensor is connected
to I2C interface of Qseven MXM connector (66th and 68th Pin) and interrupt is connected to 186th Pin of
Qseven MXM connector. This sensor (U58) is physically located on the bottom of the board as shown in
Figure 29
2.8.5.3 3-Axis Accelerometer
The Qseven Generic Carrier Board supports on board 3-Axis Accelerometer. This sensor is connected to
I2C interface of Qseven MXM connector (66th and 68th Pin) and interrupt is connected to 187th Pin of
Qseven MXM connector. This sensor is physically located on the bottom (U46) of the board as shown in
Figure 29
2.8.5.4 Altimeter/Barometer
The Qseven Generic Carrier Board supports on board Altimeter/Barometer. This sensor is connected to
I2C interface of Qseven MXM connector (66th and 68th Pin) and interrupt is connected to 189th Pin of
Qseven MXM connector. This sensor (U60) is physically located on the bottom of the board as shown in
Figure 29
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 90 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.6 Add-on Headers
2.8.6.1 SPI Header
Qseven Generic Carrier Board supports SPI header for SPI interface expansion. SPI signals from Qseven
MXM connector is connected to this SPI header (J29) and physically located at the bottom of board as
shown below.
Number of Pins: 8
Connector Part number: GRPB081VWVN-RC
Mating Connector: LPPB081NFFN-RC from Sullins Connector Solutions
Figure 30: SPI Header
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 91 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 32: SPI Header Pin Out
Pin No
Pin Name
Signal Type
1
SPI_CS0#
Output
Voltage Level/
Termination
3.3V CMOS
2
SPI_MISO
Input/Output
3.3V CMOS
3
4
GND
SPI_MOSI
Power
Input/Output
0V
3.3V CMOS
5
SPI_SCK
Output
3.3V CMOS
6
7
VCC_3V3
SPI_CS1#
Power
Output
3.3V
3.3V CMOS
8
GND
Power
0V
iWave Systems Technologies Pvt. Ltd.
Description
SPI Chip select 0.
Connected to 200th Pin of Qseven
MXM Connector.
SPI Master In Slave Out.
Connected to 201st Pin of Qseven
MXM Connector.
Ground.
SPI Master Out Slave In.
Connected to 199th Pin of Qseven
MXM Connector.
SPI clock.
Connected to 203rd Pin of Qseven
MXM Connector.
3.3V Power Supply.
SPI Chip select1.
Connected to 202nd Pin of Qseven
MXM Connector.
Ground.
Rev 2.2
Page 92 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.6.2 LPC Header (Optional)
LPC signals from the Qseven MXM Connector are connected to a 12 pin SMD pad header (J34) for LPC
interface. These SMD pads can be accessed at the bottom of the board as shown below.
Figure 31: LPC Header
Table 33: LPC Header Pin Out
Pin No
1
2
3
Pin Name
NC
NC
VGA_HSYNC
Signal Type
NC
NC
Output
Voltage Level/
Termination
NC
NC
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
No Connection.
No Connection.
VGA HSYNC.
Connected to 74th Pin of
Expansion Connector2.
Rev 2.2
Page 93 of 168
Generic Qseven Carrier Board Hardware User Guide
4
VGA_VSYNC
Output
3.3V CMOS
5
LPC_AD0/GP0
Input/Output
3.3V CMOS
6
LPC_AD1/GP1
Input/Output
3.3V CMOS
7
LPC_AD2/GP2
Input/Output
3.3V CMOS
8
LPC_AD3/GP3
Input/Output
3.3V CMOS
9
LPC_CLK/GP4
Input/Output
3.3V CMOS
10
LPC_FRAME#/GP5 Input/Output
3.3V CMOS
11
SERIRQ/GP6
Input/Output
3.3V CMOS
12
LPC_LDRQ#/GP7
Input/Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
VGA VSYNC.
Connected to 76th Pin of
Expansion Connector2.
GPIO connected to Touch
interrupt.
Connected to 185th Pin of
Qseven MXM Connector Pin.
GPIO connected to Digital
eCompass interrupt.
Connected to 186th Pin of
Qseven MXM Connector.
GPIO connected to 3-Axis
Accelerometer interrupt.
Connected to 187th Pin of
Qseven MXM Connector.
GPIO connected to Ambient
Light Sensor interrupt.
Connected to 188th Pin of
Qseven MXM Connector.
GPIO connected to Altimeter/
Barometer interrupt.
Connected to 189th Pin of
Qseven MXM Connector Pin.
GPIO connected to SATA.
Connected to 190th Pin of
Qseven MXM Connector.
GPIO connected to MIPI power
down signal.
Connected to 191st Pin of
Qseven MXM Connector.
GPIO connected to USB power
switch.
Connected to 192nd Pin of
Qseven MXM Connector.
Rev 2.2
Page 94 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.6.3 SDVO Header (Optional)
SDVO signals from the Qseven MXM Connector are connected to a 12 pin SMD pad header (J47) for
SDVO interface. These SMD pads can be accessed at the bottom of the board as shown below.
Figure 32: SDVO Header
Table 34: SDVO Header Pin Out
Pin No
1
2
Pin Name
GND
NC_SDVO_INT+
Signal Type
GND
Input
Voltage Level/
Termination
GND
TMDS
iWave Systems Technologies Pvt. Ltd.
Description
Ground
HDMI differential interrupt
positive.
Connected to 132nd Pin of
Qseven MXM Connector.
Rev 2.2
Page 95 of 168
Generic Qseven Carrier Board Hardware User Guide
3
SMB_ALERT#
Output
3.3V CMOS
4
NC_SDVO_INT-
Input
TMDS
5
FAN_GP_TIMER_IN
Output
3.3V CMOS
6
NC_SDVO_FLDSTALL+ Input/Output
TMDS
7
FAN_PWM_OUT1
Input
3.3V CMOS
8
NC_SDVO_FLDSTALL-
Input/Output
TMDS
9
DP_HPD#
Output
3.3V CMOS
10
NC_SDVO_TVCLKIN+
Input
TMDS
11
12
GND
NC_SDVO_TVCLKIN-
GND
Input
GND
TMDS
iWave Systems Technologies Pvt. Ltd.
System Management Bus Alert.
Connected to 64th Pin from
Qseven MXM Connector.
HDMI differential interrupt
positive.
Connected to 134th of Qseven
MXM Connector.
Fan tachometer input.
Connected from 195th Pin of
Qseven MXM Connector.
HDMI differential device control
data positive.
Connected to 138th Pin of
Qseven MXM Connector.
Fan PWM.
Connected to 196th Pin of
Qseven MXM Connector.
HDMI differential device control
data negative.
Connected to 140th Pin of
Qseven MXM Connector.
Tamper Switch.
Connected from 154th Pin of
Qseven MXM Connector.
HDMI differential clock data
positive.
Connected to 144th Pin of
Qseven MXM Connector.
Ground.
HDMI differential clock data
negative.
Connected to 146th Pin of
Qseven MXM Connector.
Rev 2.2
Page 96 of 168
Generic Qseven Carrier Board Hardware User Guide
2.8.6.4 Qseven Control Signal Header (Optional)
Control signals from the Qseven MXM Connector are connected to a 12 pin SMD pad header (J53) for
Control Signal expansion. These SMD pads can be accessed at the bottom of the board as shown below.
Figure 33: Qseven Control Signal
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 97 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 35: Qseven Control Signal Header
Pin No
1
2
Pin Name
NC_RSVD2
WDTRIG#
Signal Type
NC
Input
Voltage Level/ Termination
NC
3.3V CMOS
3
SUS_STAT#
Output
3.3V CMOS
4
WDOUT
Output
3.3V CMOS
5
SLP_BTN#
Input
3.3V CMOS
6
LID_BTN#
Input
3.3V CMOS
7
8
GND
WAKE#
Power
Input
GND
3.3V CMOS
9
BATLOW#
Input
3.3V CMOS
10
BIOS_DSIABLE#
Input
3.3V CMOS
11
THRM#
Input
3.3V CMOS
12
THRMTRIP#
Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
No Connection.
Watchdog trigger signal.
Connected from 70th Pin of
Qseven MXM Connector.
Suspend Status.
Connected to 19th Pin of Qseven
MXM Connector.
Watchdog event indicator.
Connected to 72nd Pin of Qseven
MXM Connector.
Sleep button.
Connected from 21st Pin of
Qseven MXM Connector.
LID Button.
Connected from 22nd Pin of
Qseven MXM Connector.
Ground.
External system wake event.
Connected from 17th Pin of
Qseven MXM Connector.
Battery low indication.
Connected from 27th Pin of
Qseven MXM Connector.
Module BIOS disable.
Connected from 41st Pin of
Qseven MXM Connector.
Thermal Alarm active low signal.
Connected from 69th Pin of
Qseven MXM Connector.
Thermal Trip indicates an
overheating condition of the
Processor.
Connected to 71st Pin of Qseven
MXM Connector.
Rev 2.2
Page 98 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9
Expansion Connectors
The Qseven Generic Carrier Board has two 80pin board to board expansion connectors. Since Qseven
edge connector pull-out only a selected set of interfaces as per Qseven standard, these two expansion
connectors are used in iWave’s Qseven CPU modules to bring more interfaces from CPU. These
Expansion connectors Expansion Connector 1 (J14) and Expansion Connector 2 (J9) are physically located
at the top of the board as shown in Figure 34 & Figure 35 respectively.
Number of Pins: 80
Connector Part number: DF17(3.0)-80DS-0.5V(57)
Mating Connector: DF17(2.0)-80DP-0.5V(57) from Hirose Electric Co Ltd
Note: iWave has made careful effort to make these expansion connectors pinout to be same for all
iWave Qseven CPU modules. But there are some signals in these connectors may be different between
CPU modules because of respective CPU supported interface. For more information about Expansion
Connector pin out, refer corresponding Qseven CPU Module’s Hardware User Manual.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 99 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 34: Expansion Connector 1
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 100 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 36: Expansion Connector1 Pin Out
Pin
No
1
Signal Name
Signal Type
Description
Power
Input/Output
Voltage Level/
Termination
0V
3.3V CMOS
GND
GPPIN_0
3
GPPIN_1
Input/Output
3.3V CMOS
4
GPPIN_2
Input/Output
3.3V CMOS
5
GPPIN_3
Input/Output
3.3V CMOS
General Purpose Pin1.
Connected to 95th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin2.
Connected to 94th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin3.
Connected to 93rd Pin of Carrier
Board Expansion Connector (J10).
6
GPPIN_4
Input/Output
3.3V CMOS
General Purpose Pin4.
Connected to 92nd Pin of Carrier
Board Expansion Connector (J10).
7
GPPIN_5
Input/Output
3.3V CMOS
General Purpose Pin5.
Connected to 91st Pin of Carrier
Board Expansion Connector (J10).
8
GPPIN_6
Input/Output
3.3V CMOS
General Purpose Pin6.
Connected to 90th Pin of Carrier
Board Expansion Connector (J10).
9
GPPIN_7
Input/Output
3.3V CMOS
10
GPPIN_8
Input/Output
3.3V CMOS
11
GPPIN_9
Input/Output
3.3V CMOS
General Purpose Pin7.
Connected to 89th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin8.
Connected to 88th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin9.
Connected to 87th Pin of Carrier
Board Expansion Connector (J10).
2
iWave Systems Technologies Pvt. Ltd.
Ground.
General Purpose Pin0.
Connected to 96th Pin of Carrier
Board Expansion Connector (J10).
Rev 2.2
Page 101 of 168
Generic Qseven Carrier Board Hardware User Guide
12
GPPIN_10
Input/Output
3.3V CMOS
13
GPPIN_11
Input/Output
3.3V CMOS
14
GPPIN_12
Input/Output
3.3V CMOS
General Purpose Pin12.
Connected to 84th Pin of Carrier
Board Expansion Connector (J10).
15
GPPIN_13
Input/Output
3.3V CMOS
General Purpose Pin13.
Connected to 83rd Pin of Carrier
Board Expansion Connector (J10).
16
GPPIN_14
Input/Output
3.3V CMOS
General Purpose Pin14.
Connected to 82nd Pin of Carrier
Board Expansion Connector (J10).
17
GPPIN_15
Input/Output
3.3V CMOS
General Purpose Pin15.
Connected to 81st Pin of Carrier
Board Expansion Connector (J10).
18
GPPIN_16
Input/Output
3.3V CMOS
General Purpose Pin16.
Connected to 78th Pin of Carrier
Board Expansion Connector (J10).
19
GPPIN_PWM2
Input
3.3V CMOS
20
GPPIN_20
Input/Output
3.3V CMOS
General Purpose Pin PWM2 input.
Connected to 54th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin20.
Connected to 74th Pin of Carrier
Board Expansion Connector (J10).
21
CAN2_PD
Input
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
General Purpose Pin10.
Connected to 86th Pin of Carrier
Board Expansion Connector (J10).
General Purpose Pin11.
Connected to 85th Pin of Carrier
Board Expansion Connector (J10).
CAN2 Power Down.
Connected 73rd Pin of Carrier
Expansion Connector (J10).
Optionally connected to CAN2
transceiver power down pin
through resistor and default not
populated.
Rev 2.2
Page 102 of 168
Generic Qseven Carrier Board Hardware User Guide
22
CAN1_PD
Input
3.3V CMOS
CAN1 Power Down.
Connected to CAN1 transceiver
power down pin & to 72nd Pin of
Carrier Expansion Connector (J10).
23
LVDS2_BLEN
Input
3.3V CMOS
LVDS2 Backlight enable.
Connected to 71st pin of Carrier
Expansion Connector (J10).
Optionally connected to LVDS2
backlight enable through resistor
and default not populated.
24
W_DISABLE
Input
3.3V CMOS
25
LVDS2_PPEN
Input
3.3V CMOS
26
LS_ADC1_PD
Input
3.3V CMOS
Wireless Disable.
Connected to 20th Pin of Mini PCIe
connector (J52) & to 70th Pin of
Carrier Expansion Connector (J10).
LVDS2 power enable.
Connected to 69th Pin of Carrier
Expansion Connector (J10)
Optionally connected to LVDS2
power enable through resistor and
default not populated.
TV decoder Power down.
Connected to TV decoder Power
down pin & to 68th Pin of Carrier
Expansion Connector (J10).
27
28
GND
LS_ADC1_GLCO
Power
Output
0V
3.3V CMOS
29
ADC1_INTREQ
Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Ground.
TV decoder GLCO.
Connected to TV decoder GLCO pin
& to 67th Pin of Carrier Expansion
Connector (J10).
TV decoder interrupt.
Connected to TV decoder INT pin &
to 66th Pin of Carrier Expansion
connector (J10).
Rev 2.2
Page 103 of 168
Generic Qseven Carrier Board Hardware User Guide
30
LS_ADC1_AVID
Output
3.3V CMOS
TV decoder active video indicator.
Connected to TV decoder AVID pin
& to 65th Pin of Carrier Expansion
connector (J10).
31
MIC_IN_DETECT
Output
3.3V CMOS
Micro phone input.
Connected to 4th Pin of Audio In
Mono Jack (J23) & to 64th Pin of
Carrier Expansion Connector (J10).
32
33
GND
GPAI_MCLK
Power
Input/Output
0V
3.3V CMOS
34
GPAI_LRCK
Input/Output
3.3V CMOS
35
GPAI_BCLK
Input/Output
3.3V CMOS
36
GPAI_DATA
Input/Output
3.3V CMOS
37
38
GND
HP_DETECT
Power
Output
0V
3.3V CMOS
Ground.
General Purpose Interface.
Connected to 51st Pin of Carrier
Expansion Connector (J10).
General Purpose Interface.
Connected to 52nd Pin of Carrier
Expansion Connector (J10).
General Purpose Interface.
Connected to 49th Pin of Carrier
Expansion Connector (J10).
General Purpose Interface.
Connected to 50th Pin of Carrier
Expansion Connector (J10).
Ground.
Headphone detect.
Connected to 4th Pin of Audio Out
Stereo Jack (J24) & to 58th Pin of
Carrier Expansion Connector (J10).
39
40
GND
LVDS_BLEN
Power
Input
0V
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Ground.
LVDS backlight enable.
Default NC.
Optionally Connected to 114th Pin
of Carrier Expansion Connector
(J10) through resistor and default
not populated.
Rev 2.2
Page 104 of 168
Generic Qseven Carrier Board Hardware User Guide
41
TSC_INT#
Output
3.3V CMOS
Touch interrupt.
Connected to touch interface
interrupt & to 53rd Pin of Carrier
Expansion connector (J10).
42
EXP1_PIN42
Power
0V
43
AC97_IRQOUT
Output
3.3V CMOS
Ground.
Connected to ground through
resistor.
AC’97 interrupt request.
Connected to AC’97 Audio CODEC
IRQOUT pin & to 55th Pin of Carrier
Expansion Connector (J10).
44
45
GND
GPAO_DATA
Power
Input/Output
0V
3.3V CMOS
Ground.
General Purpose Interface.
Connected to 102nd Pin of Carrier
Expansion Connector (J10).
46
GPAO_BCLK
Input/Output
3.3V CMOS
47
GPAO_LRCK
Input/Output
3.3V CMOS
48
AO_MCLK
Input/Output
3.3V CMOS
49
50
GND
UART1_TXD
Power
Input
0V
3.3V CMOS
51
UART1_RTS
Output
3.3V CMOS
General Purpose Interface.
Connected to 101st Pin of carrier
Expansion Connector (J10).
General Purpose Interface.
Connected to 100th Pin of carrier
Expansion Connector (J10).
General Purpose Interface.
Connected to 99th Pin of Carrier
Expansion connector (J10).
Ground.
UART1 Transmit signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.
UART1 Ready To Send signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 105 of 168
Generic Qseven Carrier Board Hardware User Guide
52
UART1_RXD
Output
3.3V CMOS
53
UART1_CTS
Input
3.3V CMOS
54
55
GND
WIFI_PDN
Power
Input
0V
3.3V CMOS
56
WL_HOST_WKUP
Input
3.3V CMOS
57
HOST_WL_WKUP
Output
3.3V CMOS
Host wake up.
Connected to 60th Pin of Carrier
Expansion Connector (J10).
Optionally connected to 17th Pin of
Wi-Fi Module Connector (J56)
through resistor and default not
populated
58
CAM_PWDN
Input
3.3V CMOS
CMOS camera power down.
Connected to 8th Pin of CMOS
Camera Connector (J51) & to 57th
Pin of Carrier Expansion Connector
(J10).
iWave Systems Technologies Pvt. Ltd.
UART1 Receive signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.
UART1 Clear to Send signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.
Ground.
Wi-Fi power down.
Connected to 63rd Pin of Carrier
Expansion Connector (J10).
Optionally connected to 14th Pin of
Wi-Fi Module connector (J56)
through resistor and default not
populated.
WLAN wake up.
Connected to 59th Pin of Carrier
Expansion Connector (J10).
Optionally connected to 16th Pin of
Wi-Fi Module Connector (J56)
through resistor and default not
populated.
Rev 2.2
Page 106 of 168
Generic Qseven Carrier Board Hardware User Guide
59
60
GND
UART2_RXD
Power
Output
0V
3.3V CMOS
Ground.
UART2 Receive signal.
Connected to 3rd pin of UART2
header (J45) through UART2 RS232
transceiver.
61
UART2_485RE#
Output
3.3V CMOS
UART2 Ready to Send signal.
Connected to 4th pin of UART2
header (J45) through UART2 RS232
transceiver.
62
UART2_485DE
Input
3.3V CMOS
UART2 Clear to Send signal.
Connected to 2nd pin of UART2
header (J45) through UART2 RS232
transceiver.
63
UART2_TXD
Input
3.3V CMOS
UART2 Transmit signal.
Connected to 1st pin of UART2
header (J45) through UART2 RS232
transceiver.
64
CSI1_MCLK
Input
3.3V CMOS
65
CSI1_PCLK
Output
3.3V CMOS
CSI port1 Master clock.
Default NC.
Optionally Connected to TV
decoder reference clock input
through resistor and default not
populated.
CSI port1 Pixel clock.
Connected to TV decoder PCLK pin.
66
CSI1_HSYNC
Output
3.3V CMOS
67
CS1_VCLK
Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
CSI port1 HSYNC.
Connected to TV decoder HSYNC
pin.
CSI port1 data enable.
Default NC.
Optionally Connected to 13th Pin of
CMOS Camera Connector (J51)
through resistor and default not
populated.
Rev 2.2
Page 107 of 168
Generic Qseven Carrier Board Hardware User Guide
68
CSI1_VSYNC
Output
3.3V CMOS
69
CSI1_DAT0
Output
3.3V CMOS
70
CSI1_DAT1
Output
3.3V CMOS
71
CSI1_DAT2
Output
3.3V CMOS
72
CSI1_DAT3
Output
3.3V CMOS
73
CSI1_DAT4
Output
3.3V CMOS
74
CSI1_DAT6
Output
3.3V CMOS
75
CSI1_DAT7
Output
3.3V CMOS
76
CSI1_DAT5
Output
3.3V CMOS
77
GPPIN_17
Input/Output
3.3V CMOS
78
GPIN18_CAN1_RXD
Output
3.3V CMOS
79
GPIN19_CAN1_TXD
Input
3.3V CMOS
80
GND
Power
0V
iWave Systems Technologies Pvt. Ltd.
CSI port1 VSYNC.
Connected to TV decoder VSYNC
pin.
CSI port1 data bit0.
Connected to TV decoder Data0
pin.
CSI port1 data bit1.
Connected to TV decoder Data1
pin.
CSI port1 data bit2.
Connected to TV decoder Data2
pin.
CSI port1 data bit3.
Connected to TV decoder Data3
pin.
CSI port1 data bit4.
Connected to TV decoder Data4
pin.
CSI port1 data bit6.
Connected to TV decoder Data6
pin.
CSI port1 data bit7.
Connected to TV decoder Data7
pin.
CSI port1 data bit5.
Connected to TV decoder Data5
pin.
General Purpose Pin 17.
Connected to 77th Pin of Carrier
Expansion Connector (J10).
CAN2 Receive signal.
Connected to CAN2 transceiver &
to 76th Pin of Carrier Expansion
Connector (J10).
CAN2 Transmit signal.
Connected to CAN2 transceiver &
to 75th Pin of Carrier Expansion
Connector (J10).
Ground.
Rev 2.2
Page 108 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 35: Expansion Connector 2
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 109 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 37: Expansion Connector2 Pin Out
Pin
No
1
Signal Name
Signal Type
Description
Output
Voltage Level/
Termination
Analog
TSC_X2
2
TSC_X1
Output
Analog
3
TSC_Y2
Output
Analog
Touch X1-axis.
Connected to 2nd Pin of VGA
Interface Header (J38).
Optionally connected to 4th Pin of
touch Connector (J50) through
resistor and default not populated.
Touch Y2-axis.
Connected to 3rd Pin of VGA
Interface Header (J38).
Optionally connected to 3rd Pin of
touch Connector (J50) through
resistor and default not populated.
4
TSC_Y1
Output
Analog
Touch Y1-axis.
Connected to 4th Pin of VGA
Interface Header (J38).
Optionally connected to 1st Pin of
touch Connector (J50) through
resistor and default not populated
5
6
7
GND
GND
KP_ROW0
Power
Power
Input/Output
0V
0V
3.3V CMOS
8
KP_ROW1
Input/Output
3.3V CMOS
Ground.
Ground.
Keypad Row0.
Connected to 1st Pin of Keypad
Header (J46).
Keypad Row1.
Connected to 2nd Pin of Keypad
Header (J46).
iWave Systems Technologies Pvt. Ltd.
Touch X2-axis.
Connected to 1st Pin of VGA
Interface Header (J38).
Optionally connected to 2nd Pin of
touch Connector (J50) through
resistor and default not populated.
Rev 2.2
Page 110 of 168
Generic Qseven Carrier Board Hardware User Guide
9
10
11
12
13
14
15
16
17
18
19
20
21
22
KP_ROW2
KP_ROW3
KP_COL0
KP_COL1
KP_COL2
KP_COL3
GND
GND
GPEM_DA1
GPEM_DA0
GPEM_DA3
GPEM_DA2
GPEM_DA5
GPEM_DA4
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Power
Power
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
iWave Systems Technologies Pvt. Ltd.
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
Keypad Row2.
Connected to 3rd Pin of
Header (J46).
Keypad Row3.
Connected to 4th Pin of
Header (J46).
Keypad Column0.
Connected to 7th Pin of
Header (J46).
Keypad Column1.
Connected to 8th Pin of
Header (J46).
Keypad Column2.
Connected to 9th Pin of
Header (J46).
Keypad Column3.
Connected to 10th Pin of
Header (J46).
Ground.
Ground.
EIM Data & address line 1.
Connected to 45th Pin of
Expansion Connector (J10).
EIM Data & address line 0.
Connected to 46th Pin of
Expansion Connector (J10).
EIM Data & address line 3.
Connected to 43rd Pin of
Expansion Connector (J10).
EIM Data & address line 2.
Connected to 44th Pin of
Expansion Connector (J10).
EIM Data & address line 5.
Connected to 41st Pin of
Expansion Connector (J10).
EIM Data & address line 4.
Connected to 42nd Pin of
Expansion Connector (J10).
Keypad
Keypad
Keypad
Keypad
Keypad
Keypad
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Rev 2.2
Page 111 of 168
Generic Qseven Carrier Board Hardware User Guide
23
24
25
26
27
28
29
30
31
32
33
34
35
36
GPEM_DA7
GPEM_DA6
GPEM_DA9
GPEM_DA8
GPEM_DA11
GPEM_DA10
GPEM_DA13
GPEM_DA12
GPEM_DA15
GPEM_DA14
GND
GND
GPEM_RW
GPEM_CS0
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Power
Power
Input
Input
iWave Systems Technologies Pvt. Ltd.
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
3.3V CMOS
EIM Data & address line 7.
Connected to 39th Pin of
Expansion Connector (J10).
EIM Data & address line 6.
Connected to 40th Pin of
Expansion Connector (J10).
EIM Data & address line 9.
Connected to 37th Pin of
Expansion Connector (J10).
EIM Data & address line 8.
Connected to 38th Pin of
Expansion Connector (J10).
EIM Data & address line 11.
Connected to 35th Pin of
Expansion Connector (J10).
EIM Data & address line 10.
Connected to 36th Pin of
Expansion Connector (J10).
EIM Data & address line 13.
Connected to 33rd Pin of
Expansion Connector (J10).
EIM Data & address line 12.
Connected to 34th Pin of
Expansion Connector (J10).
EIM Data & address line 15.
Connected to 31st Pin of
Expansion Connector (J10).
EIM Data & address line 14.
Connected to 32nd Pin of
Expansion Connector (J10).
Ground.
Ground.
EIM Read/Write Enable.
Connected to 27th Pin of
Expansion Connector (J10).
EIM Chip Select0.
Connected to 28th Pin of
Expansion Connector (J10).
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Carrier
Rev 2.2
Page 112 of 168
Generic Qseven Carrier Board Hardware User Guide
37
GPEM_BCLK
Input
3.3V CMOS
38
GPEM_CRE
Input
3.3V CMOS
39
GPEM_EB1
Input
3.3V CMOS
40
GPEM_WAIT
Output
3.3V CMOS
41
SSI_RXD
Output
3.3V CMOS
42
GPEM_EB0
Input
3.3V CMOS
43
SSI_TXFS
Input
3.3V CMOS
44
SSI_TXD
Input
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
EIM Burst Clock.
Connected to 25th Pin of Carrier
Expansion Connector (J10).
EIM Memory Register Set.
Connected to 26th Pin of Carrier
Expansion Connector (J10).
EIM Enable Byte1.
Connected to 23rd Pin of Carrier
Expansion Connector (J10).
EIM Ready/Busy/Wait.
Connected to 24th Pin of Carrier
Expansion Connector (J10).
SSI Receive Signal.
Connected to 21st Pin of Carrier
Expansion Connector (J10).
Optionally connected to 49th Pin of
Mini PCIe Connector (J52) through
resistor and default not populated.
EIM Enable Byte0.
Connected to 22nd Pin of Carrier
Expansion Connector (J10).
SSI Transmit Frame.
Connected to 19th Pin of Carrier
Expansion Connector (J10).
Optionally connected to 51st Pin of
Mini PCIe Connector (J52) through
resistor and default not populated.
SSI Transmit.
Connected to 20th Pin of Carrier
Expansion Connector (J10).
Optionally connected to 47th Pin of
Mini PCIe Connector (J52) through
resistor and default not populated.
Rev 2.2
Page 113 of 168
Generic Qseven Carrier Board Hardware User Guide
45
SSI_TXC
Output
3.3V CMOS
46
47
48
GND
GND
CSI2_D3
Power
Power
Output
0V
0V
3.3V CMOS
49
CSI2_D2
Output
3.3V CMOS
CSI Port2 data bit2.
Connected to 19th Pin of CMOS
Camera Connector (J51).
50
CSI2_D5
Output
3.3V CMOS
CSI Port2 data bit5.
Connected to 22nd Pin of CMOS
Camera Connector (J51).
51
CSI2_D4
Output
3.3V CMOS
CSI Port2 data bit4.
Connected to 20th Pin of CMOS
Camera Connector (J51).
52
CSI2_D7
Output
3.3V CMOS
CSI Port2 data bit7.
Connected to 16th Pin of CMOS
Camera Connector (J51).
53
CSI2_D6
Output
3.3V CMOS
CSI Port2 data bit6.
Connected to 18th Pin of CMOS
Camera Connector (J51).
54
CSI2_D8
Output
3.3V CMOS
55
CSI2_D9
Output
3.3V CMOS
CSI Port2 data bit8.
Connected to 14th Pin of CMOS
Camera Connector (J51).
CSI Port2 data bit9.
Connected to 12th Pin of CMOS
Camera Connector (J51).
56
CSI2_HSYNC
Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
SSI Transmit clock.
Connected to 18th Pin of Carrier
Expansion Connector (J10).
Optionally connected to 45th Pin of
Mini PCIe Connector (J52) through
resistor and default not populated.
Ground.
Ground.
CSI Port2 data bit3.
Connected to 21st Pin of CMOS
Camera Connector (J51).
CSI Port2 HSYNC.
Connected to 9th Pin of CMOS
Camera Connector (J51).
Rev 2.2
Page 114 of 168
Generic Qseven Carrier Board Hardware User Guide
57
CSI2_VSYNC
Output
3.3V CMOS
CSI Port2 VSYNC.
Connected to 7th Pin of CMOS
Camera Connector (J51).
58
CSI2_PIXCLK
Output
3.3V CMOS
CSI Port2 Pixel Clock.
Connected to 17th Pin of CMOS
Camera Connector (J51).
59
60
61
GND
GND
IOUTF/ CSI_CLK0P
Power
Power
Output
0V
0V
Differential
62
VGA_TV_RED
Input
Analog
63
GPIF_P2 / CSI_CLK0M
Output
3.3V CMOS
64
GPIF_P9
Power
0V
65
IOUTE/CSI_D0P
Output
Differential
Ground.
Ground.
MIPI CSI clock positive.
Connected to 16th Pin of MIPI
Camera Connector (J19) and to 15th
Pin of Carrier Expansion Connector
(J10)
VGA_TV Red Signal.
Connected to 2nd Pin of TV Out
Header (J30) & to 6th Pin of VGA
Interface Header (J38).
MIPI CSI clock negative.
Connected to 18th Pin of MIPI
Camera Connector (J19) and to 14th
Pin of Carrier Expansion Connector
(J10).
General Purpose Pin 9.
Connected to 7th Pin of Carrier
Expansion Connector (J10).
Optionally Connected to Ground
through resistor and default not
populated.
MIPI CSI data0 positive.
Connected to 20th Pin of MIPI
Camera Connector (J19) and to 13th
Pin of Carrier Expansion Connector
(J10)
66
VGA_TV_GRN
Input
Analog
iWave Systems Technologies Pvt. Ltd.
VGA_TV Green Signal.
Connected to 5th Pin of VGA Signal
Header (J38).
Rev 2.2
Page 115 of 168
Generic Qseven Carrier Board Hardware User Guide
67
GPIF_P4/CSI_D0M
Output
Differential
MIPI CSI data0 negative.
Connected to 22nd Pin of MIPI
Camera Connector (J19) and 12th
Pin of Carrier Expansion Connector
(J10).
68
GPIF_P10
Power
0V
69
IOUTD/CSI_D1P
Output
Differential
General Purpose Pin 10.
Connected to 6th Pin of Carrier
Expansion Connector (J10).
Optionally Connected to Ground
through resistor and default not
populated.
.MIPI CSI differential data1 positive.
Connected to 12th Pin of MIPI
Camera Connector (J19) and to 11th
Pin of Carrier Expansion Connector
(J10)
70
VGA_TV_BLU
Input
Analog
Output
71
GPIF_P6/CSI_D1M
Output
Differential
72
GPIF_P11
Power
0V
73
GPIF_P7
Input/Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Video VGA_TV Blue Signal.
Connected to 10th Pin of VGA Signal
Header (J38).
MIPI
CSI
differential
data1
negative.
Connected to 14th Pin of MIPI
Camera Connector (J19) and to 10th
Pin of Carrier Expansion Connector
(J10).
General Purpose Pin 11..
Connected to 5th Pin of Carrier
Expansion Connector (J10).
Optionally Connected to Ground
through resistor and default not
populated.
General Purpose Pin 7.
Connected to 9th Pin of Carrier
Expansion Connector (J10).
Rev 2.2
Page 116 of 168
Generic Qseven Carrier Board Hardware User Guide
74
VGA_HSYNC
Input
3.3V CMOS
75
RFOUT
NC
NC
76
VGA_VSYNC
Input
3.3V CMOS
VGA VSYNC.
Connected to 9th Pin of VGA Signal
Header (J38) & to 4th Pin of LPC
Header (J34).
77
78
79
GND
GND
CSI2_D1
Power
Power
Input/Output
0V
0V
3.3V CMOS
80
CSI2_D0
Input/Output
3.3V CMOS
Ground.
Ground.
CSI Port2 data bit1.
Connected to 23rd Pin of CMOS
Camera Connector (J51) & to 4th
Pin of Carrier Expansion Connector
(J10).
CSI Port2 data bit0.
Connected to 24th Pin of CMOS
Camera Connector (J51) & to 3rd
Pin of Carrier Expansion Connector
(J10).
iWave Systems Technologies Pvt. Ltd.
VGA HSYNC.
Connected to 7th Pin of VGA Signal
Header (J38) & to 3rd Pin of LPC
Header (J34).
RFOUT
Connected to 8th Pin of Carrier
Expansion Connector (J10).
Rev 2.2
Page 117 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.1 UART2 Header
The Qseven Generic Carrier Board supports 5 pin UART2 header for external UART interface. UART
signals from Expansion connector1 is connected to this header through RS232 transceiver. UART2
header (J45) is physically located at the bottom of the board as shown below.
Number of Pins: 5
Connector Part number: GRPB051VWVN-RC
Mating Connector: LPPB051NFFN-RC from Sullins Connector Solutions
Figure 36: Secondary UART Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 118 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 38: Secondary UART Connector Pin Out
Pin No
Pin Name
Signal Type
1
UART2_TXD
Output
Voltage Level/
Termination
RS232
2
UART2_CTS
Input
RS232
3
UART2_RXD
Input
RS232
4
UART2_RTS
Output
RS232
5
GND
Power
0V
Description
UART2 transmit signal.
Connected from 63rd Pin of Expansion
Connector1.
UART2 Clear to Send.
Connected to 62nd Pin of Expansion
Connector1.
UART2 receive signal.
Connected to 60th Pin of Expansion
Connector1.
UART2 Request to Send.
Connected from 61st Pin of Expansion
Connector1.
Ground.
2.9.2 CAN Port2
CAN Transmit and Receive signals from Expansion connector1 Pin 79 and 78 respectively are connected
to CAN transceiver and the output signals from the transceiver are connected to 3Pin CAN Port2
connector (J55). This connector is physically located on top of the board as shown below.
Number of Pins: 3
Connector Part number: S3B-PH-SM4-TB(LF)(SN)
Mating Connector: PHR-3 from JST Sales America Inc
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 119 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 37: Secondary CAN Connector
Table 39: CAN Port2 Connector Pin Out
Pin No
Pin Name
1
2
3
M1,M2
GND
CAN1H
CAN1L
Mechanical
Support
Signal Type
Power
Input
Input
Mechanical
Support
Voltage Level/
Termination
0V
Differential
Differential
Mechanical
Support
iWave Systems Technologies Pvt. Ltd.
Description
Ground.
CAN1 Differential Pair High Side.
CAN1 Differential Pair Low Side.
Mechanical Support.
Rev 2.2
Page 120 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.3 TV-In RCA Jack
The Qseven Generic Carrier Board supports TV-In interface through On-board TV-In Decoder chip
“TVP5150AM1” from Texas Instruments. This decoder chip converts NTSC/PAL composite video input
from TV IN RCA jack (J1) to CMOS camera interface signals. This CMOS camera interface signals are
connected to CSI port1 pins of Expansion connector1. TV-In RCA Jack (J1) is physically located on top of
board as shown below.
Figure 38: TV-IN Connector
Table 40: TV-In Connector Pin Out
Pin No
1
2
3
4
Pin Name
GND
VIDEO_IN_A
GND
GND
Signal Type
Power
Input
Power
Power
Voltage Level/
Termination
0V
Analog
0V
0V
iWave Systems Technologies Pvt. Ltd.
Description
Ground.
Analog Video input.
Ground.
Ground.
Rev 2.2
Page 121 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.4 CMOS Camera Connector
The Qseven Generic Carrier Board supports 24pin CMOS Camera connector (J51) for CMOS camera
interface. This connector supports 8bit CMOS camera interface signals and connected to CSI port2 pins
of Expansion connector2 through 2.8V to 3.3V Voltage translator. External reference clock for camera is
provided by using on-board 26MHz Oscillator. This Camera connector (J51) is physically located at the
bottom of the board as shown below.
Compatible Camera
Part Number: CN003VEF2052
Description: VGA lens of 640x480 pixel CMOS camera based on OV7725 sensor
Manufacturer Name: Global Optics Limited
Global Optics CMOS Camera Web link: http://www.globaloptics.cn/
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 122 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 39: Camera Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 123 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 41: Camera Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
3
STROBE
AGND
SIOD
NC
Power
Input/Output
Voltage Level/
Termination
NC
0V
2.8V CMOS
4
5
AVDD
SIOC
Power
Output
2.8V
2.8V CMOS
6
RESETB
Output
2.8V
Reset Out, Active Low.
7
VSYNC
Input
2.8V CMOS
8
PWDN
Output
2.8V CMOS
Vertical Synchronization.
Connected to 57th Pin of
Expansion Connector2.
Power Down.
Connected to 58th Pin of
Expansion Connector1.
9
HREF
Input
2.8V CMOS
Horizontal Synchronization.
Connected to 56th Pin of
Expansion Connector2.
10
11
12
DVDD
DOVDD
D9
Power
Power
Input
1.8V
2.8V
2.8V CMOS
Digital Power Supply.
IO Power Supply.
Camera Data9.
Connected to 55th Pin of
Expansion Connector2.
iWave Systems Technologies Pvt. Ltd.
Description
No Connection.
Analog Ground.
I2C Data.
Connected to 68th Pin of
Qseven MXM Connector
through Voltage translator.
Analog Power Supply.
I2C Clock.
Connected to 66th Pin of
Qseven MXM Connector
through Voltage translator.
Rev 2.2
Page 124 of 168
Generic Qseven Carrier Board Hardware User Guide
13
XCLK
Output
2.8V CMOS
Camera Reference Clock.
Connected to On-board
26Mhz Oscillator.
Also this pin is optionally
Connected to 67th Pin of
Expansion
Connector1
through resistor and default
not populated.
14
D8
Input
2.8V CMOS
Camera Data8.
Connected to 54th Pin of
Expansion Connector2.
15
16
DGND
D7
Power
Input
0V
2.8V CMOS
Digital Ground.
Camera Data7.
Connected to 52nd Pin
Expansion Connector2.
Camera Pixel Clock.
Connected to 58th Pin
Expansion Connector2.
Camera Data6.
Connected to 53rd Pin
Expansion Connector2.
Camera Data12.
Connected to 49th Pin
Expansion Connector2.
Camera Data5.
Connected to 50th Pin
Expansion Connector2.
Camera Data3
Connected to 48th Pin
Expansion Connector2.
Camera Data4.
Connected to 51st Pin
Expansion Connector2.
Camera Data1.
Connected to 79th Pin
Expansion Connector2.
Camera Data0.
Connected to 80th Pin
Expansion Connector2.
17
18
19
20
21
22
23
24
PCLK
D6
D2
D5
D3
D4
D1
D0
Input
Input
Input
Input
Input
Input
Input
Input
2.8V CMOS
2.8V CMOS
2.8V CMOS
2.8V CMOS
2.8V CMOS
2.8V CMOS
2.8V CMOS
2.8V CMOS
iWave Systems Technologies Pvt. Ltd.
of
of
of
of
of
of
of
of
of
Rev 2.2
Page 125 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.5 MIPI Camera Connector
The Qseven Generic Carrier Board supports 30pin MIPI Camera connector (J19) for MIPI camera
interface. This connector supports 2 Lane MIPI camera interface signals and connected to MIPI Interface
pins of Expansion connector2. External reference clock for MIPI camera is provided by using on-board
26MHz Oscillator. This Camera connector (J19) is physically located at the bottom of the board as shown
below.
Compatible Camera
Part Number: LI-OV5640-MIPI-AF
Description: 5MegaPixel MIPI Camera based on OV5640 sensor
Manufacturer Name: Leopard
Leopard’s MIPI Camera Web link: https://www.leopardimaging.com/LI-OV5640-MIPI-AF.html
Figure 40: 5MP MIPI Camera connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 126 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 42: MIPI Camera Connector Pin Out
Pin No
Pin Name
Signal Type
1
2
3
Strobe (NC)
AGND
SDA
NC
Power
Input/Output
Voltage Level/
Termination
NC
0V
1.8V
4
5
AVDD
SCL
Power
Output
2.8V
1.8V
6
RESET
Output
1.8V/
10K pull-up
MIPI CSI Reset
7
8
NC1
PWDN
NC
Output
NC
1.8V
No Connection
MIPI CSI Power Down.
Connected to 191st Pin of Qseven
MXM Connector.
9
10
11
12
NC2
DVDD
DOVDD
MDP1
NC
Power
Power
Input
NC
1.5V
1.8V
Differential
No Connection
Digital Power 1.5V
Digital Power 1.8V
MIPI Lane1 Data Positive.
Connected from 69th Pin
Expansion Connector2.
13
XCLK
Output
1.8V
14
MDN1
Input
Differential
15
16
DGND
MCP
Power
Input
0V
Differential
17
NC3
NC
NC
iWave Systems Technologies Pvt. Ltd.
Description
No Connection
Analog Ground
I2C Data.
Connected to 68th Pin of Qseven
MXM Connector.
Analog Power 2.8V
I2C Clock.
Connected to 66th Pin of Qseven
MXM Connector.
of
MIPI CSI Master Clock.
Connected to on-board 26Mhz
Oscillator.
MIPI Lane1 Data Negative.
Connected from 71st Pin of
Expansion Connector2.
Ground.
MIPI Clock Positive.
Connected to 61st Pin of Expansion
Connector2.
No Connection
Rev 2.2
Page 127 of 168
Generic Qseven Carrier Board Hardware User Guide
18
MCN
Input
Differential
MIPI Clock Negative.
Connected from 63rd
Expansion Connector2.
Pin
of
19
NC4
NC
NC
No Connection
20
MDP0
Input
Differential
MIPI Lane0 Data Positive.
Connected to 65th Pin of Expansion
Connector2.
21
22
NC5
MDN0
NC
Input
NC
Differential
No Connection
MIPI Lane0 Data Negative.
Connected from 67th Pin
Expansion Connector2.
23
AF-VCC
Power
1.8V
MIPI AF Power 1.8V.
24
AF-GND
Power
0V
Analog Field Ground.
iWave Systems Technologies Pvt. Ltd.
of
Rev 2.2
Page 128 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.6 Keypad Header
The Qseven Generic Carrier Board supports 10pin keypad interface header (J46) for Keypad interface.
This header supports 4X4 keypad interface signals and connected to Expansion connector2. Keypad
Header (J46) is physically located at the bottom of board as shown below.
Number of Pins: 10
Connector Part number: GRPB052VWVN-RC
Mating Connector: LPPB052CFFN-RC from Sullins Connector Solutions
Figure 41: Keypad Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 129 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 43: Keypad Connector Pin Out
Pin No
Pin Name
Signal Type
1
KP_ROW0
Input/Output
Voltage Level/
Termination
3.3V CMOS
2
KP_ROW1
Input/Output
3.3V CMOS
3
KP_ROW2
Input/Output
3.3V CMOS
4
KP_ROW3
Input/Output
3.3V CMOS
5
6
7
GND
GND
KP_COL0
Power
Power
Input/Output
0V
0V
3.3V CMOS
8
KP_COL1
Input/Output
3.3V CMOS
9
KP_COL2
Input/Output
3.3V CMOS
10
KP_COL3
Input/Output
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
Keypad Row0.
Connected to 7th Pin of Expansion
Connector2.
Keypad Row1.
Connected to 8th Pin of Expansion
Connector2.
Keypad Row2.
Connected to 9th Pin of Expansion
Connector2.
Keypad Row3.
Connected to 10th Pin of Expansion
Connector2.
Ground.
Ground.
Keypad Column0.
Connected to 11th Pin of Expansion
Connector2.
Keypad Column1.
Connected to 12th Pin of Expansion
Connector2.
Keypad Column2.
Connected to 13th Pin of Expansion
Connector2.
Keypad Column3.
Connected to 14th Pin of Expansion
Connector2.
Rev 2.2
Page 130 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.7 TV Out Header
NTSC/PAL composite video out signal from Expansion connector2 is connected to 2-pin header to
support TV Out interface. This header (J30) is physically is located on the bottom of the board as shown
below.
Number of Pins: 2
Connector Part number: GRPB021VWVN-RC
Mating Connector: LPPB021NFFN-RC from Sullins Connector Solutions
Figure 42: TV Out Interface Header
Table 44: TV Out Header Pin Out
Pin No
Pin Name
1
2
GND
VGA_TV_RED
Signal Type
Power
Output
Voltage Level/
Termination
0V
Analog
iWave Systems Technologies Pvt. Ltd.
Description
Ground.
Composite Video Output.
Connected to 62nd Pin of Expansion
Connector2.
Rev 2.2
Page 131 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.8 VGA Interface Header (Optional)
VGA interface signals from the Expansion connector2 is connected to 10-pin SMD pad header (J38).This
SMD pads can be accessed at the bottom of the board as shown below. By default this header will not
be populated.
Figure 43: VGA Signal Header
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 132 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 45: VGA Header Pin Out
Pin No
1
Expn2_p1
Input/Output
Voltage Level/
Termination
3.3V CMOS
2
Expn2_p2
Input/Output
3.3V CMOS
3
4
5
6
7
8
9
10
Pin Name
Expn2_p3
Expn2_p4
VGA_TV_GRN
VGA_TV_RED
VGA_HSYNC
GND
VGA_VSYNC
VGA_TV_BLU
Signal Type
Input/Output
Input/Output
Output
Output
Output
Power
Output
Output
iWave Systems Technologies Pvt. Ltd.
3.3V CMOS
3.3V CMOS
Analog
Analog
Analog
0V
Analog
Analog
Description
General Purpose Pin.
Connected to 1st Pin of
Expansion Connector2.
General Purpose Pin.
Connected to 2nd Pin
Expansion Connector2.
General Purpose Pin.
Connected to 3rd Pin
Expansion Connector2.
General Purpose Pin.
Connected to 4th Pin
Expansion Connector2.
VGA-Green.
Connected to 66th Pin
Expansion Connector2.
VGA-Red.
Connected to 62nd Pin
Expansion Connector2.
VGA-HSYNC.
Connected to 74th Pin
Expansion Connector2.
Ground.
VGA-VSYNC.
Connected to 76th Pin
Expansion Connector2.
VGA-Blue.
Connected to 70th Pin
Expansion Connector2.
of
of
of
of
of
of
of
of
Rev 2.2
Page 133 of 168
Generic Qseven Carrier Board Hardware User Guide
2.9.9 Carrier Board Expansion Connector
The Qseven Generic Carrier Board has one 120pin board to board expansion connector for external
carrier board expansion. The unused signals from Qseven Module Expansion Connectors are brought to
this connector. This Carrier Expansion Connector (J10) is physically located at the top of the board as
shown below.
Number of Pins: 120
Connector Part number: QSH-060-01-L-D-A
Mating Connector: QTH-060-02-F-D-A from Samtec Inc
Figure 44: Carrier Expansion Connector
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 134 of 168
Generic Qseven Carrier Board Hardware User Guide
Table 46: Carrier Expansion Connector Pin Outs
Pin
No
1
2
3
Signal Name
Signal Type
GND
GND
GPIF_P13
Power
Power
Input/Output
Voltage Level/
Termination
0V
0V
3.3V CMOS
4
GPIF_P12
Input/Output
3.3V CMOS
5
GPIF_P11
Input/Output
3.3V CMOS
6
GPIF_P10
Input/Output
3.3V CMOS
7
8
9
10
11
12
GPIF_P9
GPIF_P8
GPIF_P7
GPIF_P6
GPIF_P5
GPIF_P4
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
Description
Ground.
Ground.
General Purpose Pin 13.
Connected to 80th Pin of Expansion
Connector2 (J9).
General Purpose Pin 12.
Connected to 79th Pin of Expansion
Connector2 (J9).
General Purpose Pin 11.
Connected to 72nd Pin of Expansion
Connector2 (J9).
General Purpose Pin 10.
Connected to 68th Pin
Connector2 (J9).
General Purpose Pin 9.
Connected to 64th Pin
Connector2 (J9).
General Purpose Pin 8.
Connected to 75th Pin
Connector2 (J9).
General Purpose Pin 7.
Connected to 73rd Pin
Connector2 (J9).
General Purpose Pin 6.
Connected to 71st Pin
Connector2 (J9).
General Purpose Pin 5.
Connected to 69th Pin
Connector2 (J9).
General Purpose Pin 4.
Connected to 67th Pin
Conenctor2 (J9).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 135 of 168
Generic Qseven Carrier Board Hardware User Guide
13
14
15
16
17
18
19
20
21
22
23
24
25
26
GPIF_P3
GPIF_P2
GPIF_P1
GND
GND
GPSSI_TXC
GPSSI_TXFS
GPSSI_TXD
GPSSI_RXD
GPEM_EB0
GPEM_EB1
GPEM_WAIT
GPEM_BCLK
GPEM_CRE
Input/Output
Input/Output
Input/Output
Power
Power
Input
Output
Output
Input
Output
Output
Input
Output
Input
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
General Purpose Pin 3.
Connected to 65th
Connector2 (J9).
General Purpose Pin 2.
Connected to 63rd
Connector2 (J9).
General Purpose Pin 1.
Connected to 61st
Connector2 (J9).
Ground.
Ground.
SSI Transmit clock.
Connected to 45th
Conenctor2 (J9).
SSI Transmit Frame.
Connected to 43rd
Conenctor2 (J9).
SSI Transmit.
Connected to 44th
Conenctor2 (J9).
SSI Receive.
Connected to 41st
Conenctor2 (J9).
Pin of Expansion
Pin of Expansion
Pin of Expansion
Pin of Expansion
Pin of Expansion
Pin of Expansion
Pin of Expansion
EIM Enable Byte0.
Connected to 42nd Pin
Connector2 (J9).
EIM Enable Byte1.
Connected to 39th Pin
Connector2 (J9).
EIM Ready/Busy/Wait.
Connected to 40th Pin
Connector2 (J9).
EIM Burst Clock.
Connected to 37th Pin
Connector2 (J9).
EIM Memory Register Set.
Connected to 38th Pin
Connector2 (J9).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 136 of 168
Generic Qseven Carrier Board Hardware User Guide
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GPEM_RW
GPEM_CS0
GND
GND
GPEM_DA15
GPEM_DA14
GPEM_DA13
GPEM_DA12
GPEM_DA11
GPEM_DA10
GPEM_DA9
GPEM_DA8
GPEM_DA7
GPEM_DA6
Output
Output
Power
Power
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
EIM Read/Write Enable.
Connected to 35th Pin
Connector2 (J9).
EIM Chip Select0.
Connected to 36th Pin
Connector2 (J9).
Ground.
Ground.
EIM Data & address line 15.
Connected to 31st Pin
Connector2 (J9).
EIM Data & address line 14.
Connected to 32nd Pin
Connector2 (J9).
EIM Data & address line 13.
Connected to 29th Pin
Connector2 (J9).
EIM Data & address line 12.
Connected to 30th Pin
Connector2 (J9).
EIM Data & address line 11.
Connected to 27th Pin
Connector2 (J9).
EIM Data & address line 10.
Connected to 28th Pin
Connector2 (J9).
EIM Data & address line 9.
Connected to 25th Pin
Connector2 (J9).
EIM Data & address line 8.
Connected to 26th Pin
Connector2 (J9).
EIM Data & address line 7.
Connected to 23rd Pin
Connector2 (J9).
EIM Data & address line 6.
Connected to 24th Pin
Connector2 (J9).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 137 of 168
Generic Qseven Carrier Board Hardware User Guide
41
42
43
44
45
46
47
48
49
50
51
52
53
GPEM_DA5
GPEM_DA4
GPEM_DA3
GPEM_DA2
GPEM_DA1
GPEM_DA0
GND
GND
GPAI_BCLK
GPAI_DATA
GPAI_MCLK
GPAI_LRCK
GPPIN_38
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Power
Power
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
EIM Data & address line 5.
Connected to 21st Pin
Connector2 (J9).
EIM Data & address line 4.
Connected to 22nd Pin
Connector2 (J9).
EIM Data & address line 3.
Connected to 19th Pin
Connector2 (J9).
EIM Data & address line 2.
Connected to 20th Pin
Connector2 (J9).
EIM Data & address line 1.
Connected to 17th Pin
Connector2 (J9).
EIM Data & address line 0.
Connected to 18th Pin
Connector2 (J9).
Ground.
Ground.
General Purpose Interface.
Connected to 35th Pin
Connector1 (J14).
General Purpose Interface.
Connected to 36th Pin
Connector1 (J14).
General Purpose Interface.
Connected to 33rd Pin
Connector1 (J14).
General Purpose Interface.
Connected to 34th Pin
Connector1 (J14).
General Purpose Pin 38.
Connected to 41st Pin
Connector1 (J14).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 138 of 168
Generic Qseven Carrier Board Hardware User Guide
54
55
56
57
58
GPPIN_PWM2
GPPIN_36
GND
GPPIN_34
GPPIN_35
Output
Input/Output
Power
Input/Output
Input/Output
3.3V CMOS
3.3V CMOS
0V
3.3V CMOS
3.3V CMOS
General Purpose PWM.
Connected to 19th Pin
Connector1 (J14).
General Purpose Pin 36.
Connected to 43rd Pin
Connector1 (J14).
Ground.
General Purpose Pin 34.
Connected to 58th Pin
Connector1 (J14).
General Purpose Pin 35.
Connected to 38th Pin
Connector1 (J14).
of Expansion
of Expansion
of Expansion
of Expansion
59
GPPIN_32
Input/Output
3.3V CMOS
General Purpose Pin 32.
Connected to 56th Pin of Expansion
Conenctor1 (J14).
60
GPPIN_33
Input/Output
3.3V CMOS
General Purpose Pin 33.
Connected to 57th Pin
Conenctor1 (J14).
Ground.
Ground.
General Purpose Pin 31.
Connected to 55th Pin
Conenctor1 (J14).
General Purpose Pin 30.
Connected to 31st Pin
Connector1 (J14).
General Purpose Pin 29.
Connected to 30th Pin
Connector1 (J14).
General Purpose Pin 28.
Connected to 29th Pin
Connector1 (J14).
General Purpose Pin 27.
Connected to 28th Pin
Connector1 (J14).
61
62
63
64
65
66
67
GND
GND
GPPIN_31
GPPIN_30
GPPIN_29
GPPIN_28
GPPIN_27
Power
Power
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
0V
0V
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 139 of 168
Generic Qseven Carrier Board Hardware User Guide
68
69
70
71
72
73
74
75
76
77
78
79
80
81
GPPIN_26
GPPIN_25
GPPIN_24
GPPIN_23
GPPIN_22
GPPIN_21
GPPIN_20
GPPIN_19
GPPIN_18
GPPIN_17
GPPIN_16
GND
GND
GPPIN_15
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Power
Power
Input/Output
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
0V
0V
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
General Purpose Pin 26.
Connected to 26th Pin
Connector1 (J14).
General Purpose Pin 25.
Connected to 25th Pin
Connector1 (J14).
General Purpose Pin 24.
Connected to 24th Pin
Connector1 (J14).
General Purpose Pin 23.
Connected to 23rd Pin
Connector1 (J14).
General Purpose Pin 22.
Connected to 22nd Pin
Connector1 (J14).
General Purpose Pin 21.
Connected to 21st Pin
Connector1 (J14).
General Purpose Pin 20.
Connected to 20th Pin
Connector1 (J14).
General Purpose Pin 19.
Connected to 79th Pin
Conenctor1 (J14).
General Purpose Pin 18.
Connected to 78th Pin
Conenctor1 (J14).
General Purpose Pin 17.
Connected to 77th Pin
Connector1 (J14).
General Purpose Pin 16.
Connected to 18th Pin
Connector1 (J14).
Ground.
Ground.
General Purpose Pin 15.
Connected to 17th Pin
Connector1 (J14).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
Rev 2.2
Page 140 of 168
Generic Qseven Carrier Board Hardware User Guide
82
83
84
85
86
87
88
89
90
91
92
93
GPPIN_14
GPPIN_13
GPPIN_12
GPPIN_11
GPPIN_10
GPPIN_9
GPPIN_8
GPPIN_7
GPPIN_6
GPPIN_5
GPPIN_4
GPPIN_3
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
Input/Output
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
iWave Systems Technologies Pvt. Ltd.
General Purpose Pin 14.
Connected to 16th Pin
Connector1 (J14).
General Purpose Pin 15.
Connected to 15th Pin
Connector1 (J14).
General Purpose Pin 12.
Connected to 14th Pin
Connector1 (J14).
General Purpose Pin 11.
Connected to 13th Pin
Connector1 (J14).
General Purpose Pin 10.
Connected to 12th Pin
Connector1 (J14).
General Purpose Pin 9.
Connected to 11th Pin
Connector1 (J14).
General Purpose Pin 8.
Connected to 10th Pin
Connector1 (J14).
General Purpose Pin 7.
Connected to 9th Pin
Connector1 (J14).
General Purpose Pin 6.
Connected to 8th Pin
Connector1 (J14).
General Purpose Pin 5.
Connected to 7th Pin
Connector1 (J14).
General Purpose Pin 4.
Connected to 6th Pin
Connector1 (J14).
General Purpose Pin 3.
Connected to 5th Pin
Connector1 (J14).
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of Expansion
of
Expansion
of
Expansion
of
Expansion
of
Expansion
of
Expansion
Rev 2.2
Page 141 of 168
Generic Qseven Carrier Board Hardware User Guide
94
GPPIN_2
Input/Output
3.3V CMOS
95
GPPIN_1
Input/Output
3.3V CMOS
96
GPPIN_0
Input/Output
3.3V CMOS
97
98
99
GND
GND
GPAO_MCLK
Power
Power
Input/Output
0V
0V
3.3V CMOS
100
GPAO_LRCK
Input/Output
3.3V CMOS
101
GPAO_BCLK
Input/Output
3.3V CMOS
102
GPAO_DATA
Input/Output
3.3V CMOS
103
104
105
GND
GND
NC_USB_P7-
Power
Power
Input/Output
0V
0V
Differential
106
NC_USB_P6-
Input/Output
Differential
107
NC_USB_P7+
Input/Output
Differential
108
NC_USB_P6+
Input/Output
Differential
109
GND
Power
0V
iWave Systems Technologies Pvt. Ltd.
General Purpose Pin 2.
Connected to 4th Pin of Expansion
Connector1 (J14).
General Purpose Pin 1.
Connected to 3rd Pin of Expansion
Connector1 (J14).
General Purpose Pin 0.
Connected to 2nd Pin of Expansion
Connector1 (J14).
Ground.
Ground.
General Purpose Interface.
Connected to 48th Pin of Expansion
Connector1 (J14).
General Purpose Interface.
Connected to 47th Pin of Expansion
Connector1 (14).
General Purpose Interface.
Connected to 46th Pin of Expansion
Connector1 (14).
General Purpose Interface.
Connected to 45th Pin of Expansion
Connector1 (14).
Ground.
Ground.
USB Host Port7 Data negative.
Connected to 75th Pin of Qseven MXM
Connector (J12) through resistor.
USB Host Port6 Data negative.
Connected to 76th Pin of Qseven MXM
Connector (J12) through resistor.
USB Host Port7 Data positive.
Connected to 77th Pin of Qseven MXM
Connector (J12) through resistor.
USB Host Port6 Data positive.
Connected to 78th Pin of Qseven MXM
Connector (J12) through resistor.
Ground.
Rev 2.2
Page 142 of 168
Generic Qseven Carrier Board Hardware User Guide
110
111
GND
NC_USB_P5-
Power
Input/Output
0V
Differential
Ground.
USB Host Port5 Data Negative.
Connected to 81st Pin of Qseven MXM
Connector (J12) through resistor.
112 USB_4_5_OC#
Input
3.3V CMOS
Over current sense for USB port 4 & 5.
Connected to 80th Pin of Qseven MXM
Connector (J12) through resistor.
113 NC_USB_P5+
Input/Output
Differential
USB Host Port5 Data Positive.
Connected to 83rd Pin of Qseven MXM
Connector (J12) through resistor.
114 NC_USB_6_7_OC# Input
3.3V CMOS
Over current sense for USB ports 6 & 7.
Connected to 79th Pin of Qseven MXM
Connector (J12) through resistor.
115 GND
Power
0V
Ground.
116 GND
Power
0V
Ground.
117 VCC_5V
Power
5V
VCC Power Supply, 5V.
118 VCC_5V
Power
5V
VCC Power Supply, 5V.
119 VCC_5V
Power
5V
VCC Power Supply, 5V.
120 VCC_5V
Power
5V
VCC Power Supply, 5V.
Note: Carrier Board Expansion connector pin-out details of all iWave’s Qseven CPU Modules are
mentioned in the APPENDIX II section.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 143 of 168
Generic Qseven Carrier Board Hardware User Guide
3
3.1
ELECTRICAL SPECIFICATION
Qseven Generic Carrier Board Power Input Requirement
The Qseven Generic Carrier Board is designed to work with a +12V external power and uses on board
voltage regulators for internal power management. 12V power input from an external power supply is
connected to the Qseven Generic Carrier Board through Power Jack (J3). This 2.5mm x 6.5mm barrel
connector Jack should fit standard DC Plugs with an inner dimension of 2.5mm and an outer dimension
of 5.5mm. This connector is physically placed on the top of the board as shown below.
Figure 45: Power Jack
Table 47: Power Jack Pin Out
Pin No
1
2
3
Pin Name
12V
Ground
Ground
Signal Type
Power
Power
Power
Voltage Level/
Termination
12V
0V
0V
iWave Systems Technologies Pvt. Ltd.
Description
Positive Terminal.
Negative Terminal.
Negative Terminal.
Rev 2.2
Page 144 of 168
Generic Qseven Carrier Board Hardware User Guide
3.2
Power Output to Qseven CPU Module
The Qseven Generic Carrier Board provides all the necessary power to Qseven CPU Modules as
mentioned in the Qseven Specification. Qseven CPU modules require +5V (VCC) as a Main power input
and two optional power rails for +5V standby voltage & +3V RTC supply voltage.
Table 48: Power Output to Qseven CPU Modules
Sl. No.
1
2
3
Power Rail
VCC
VCC_5V_SB
VCC_RTC
Min (V)
4.75V
4.75V
-
Typical (V)
5V
5V
3V
Max(V)
5.25V
5.25V
-
The Qseven Generic Carrier Board Power Output sequencing to Qseven CPU modules are explained
below.
Figure 46: Power Sequence to Qseven CPU Module
Table 49: Power Sequence Timing to Qseven CPU Module
Item
Description
Value
T1
VCC_RTC rise time to VCC_5V_SB rise time
≥ 0 ms
Power Up
T2
VCC_5V_SB rise time to VCC rise time
0 ms
Sequence
T3
VCC rise time to PWGIN rise time
0 ms
T4
PWGIN fall time to VCC fall time
0 ms
Power Down
T5
VCC fall time to VCC_5V_SB fall time
0 ms
Sequence
T6
VCC_5V_SB fall time to VCC_RTC fall time
≥ 0 ms
Note: PWGIN is the Power Good output to Qseven CPU module. This pin is default pulled to VCC_5V_SB
power in Qseven Generic Carrier Board. Generic Carrier Board also optionally supports Power Good
circuit and default not populated.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 145 of 168
Generic Qseven Carrier Board Hardware User Guide
4
MECHANICAL SPECIFICATION
Qseven Generic Carrier Board PCB form factor is Nano-ITX with size of 120 × 120 mm (4.7inch × 4.7
inch). Qseven Generic Carrier Board PCB dimension with Mounting hole placement detail is shown in the
below figure.
Figure 47: Board Mechanical Dimension
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 146 of 168
Generic Qseven Carrier Board Hardware User Guide
5
5.1
APPENDIX I
Generic Qseven Carrier Board PCB Silk Screen
Generic Qseven Carrier Board PCB silkscreen top view and bottom view with Optional Feature’s
Identifier highlighted are shown in the below Figures. This will be useful while mounting the Optional
Features in Qseven Carrier board.
Figure 48: PCB Silkscreen Top
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 147 of 168
Generic Qseven Carrier Board Hardware User Guide
Figure 49: PCB Silkscreen Bottom
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 148 of 168
Generic Qseven Carrier Board Hardware User Guide
6
APPENDIX II
The Qseven Generic Carrier Board Expansion connector pin-out for all iWave’s Qseven CPU Modules is
mentioned in below Tables.
6.1
Expansion Pin-out based on i.MX6 SOM
Table 50: Carrier Board Expansion Connector pin-out based on i.MX6 SOM
Pin
No
1
2
3
Pin Name
based on
i.MX6 SOM
GND
GND
CSI_D3M
4
CSI_D3P
5
SD4_DAT1
6
8
UART4_RXD
(KEY_ROW0)
UART4_TXD
(KEY_COL0)
CSI_D2M
9
CSI_D2P
10
CSI_D1M
11
CSI_D1P
12
CSI_D0M
13
CSI_D0P
14
CSI_CLK0M
15
CSI_CLK0P
16
GND
7
Pin Connection
GND
GND
Connected to 80th Pin of
Expansion Connector 2
Connected to 79th Pin of
Expansion Connector 2
Connected to 72nd Pin of
Expansion Connector 2
Connected to 68th Pin of
Expansion Connector 2
Connected to 64th Pin of
Expansion Connector 2
Connected to 75th Pin of
Expansion Connector 2
Connected to 73rd Pin of
Expansion Connector 2
Connected to 71st Pin of
Expansion Connector 2
Connected to 69th Pin of
Expansion Connector 2
Connected to 67th Pin of
Expansion Connector 2
Connected to 65th Pin of
Expansion Connector 2
Connected to 63rd Pin of
Expansion Connector 2
Connected to 61st Pin of
Expansion Connector 2
GND
Signal
Type
Voltage Level/
Termination
Description
Power
Power
Input
0V
0V
Differential
Input
Differential
Input/
Output
Input
3.3V CMOS
Ground.
Ground.
MIPI CSI differential data3
negative.
MIPI CSI differential data3
positive.
General Purpose I/O.
3.3V CMOS
UART4 Receive data line.
Output
3.3V CMOS
UART4 Transmit data line.
Input
Differential
Input
Differential
Input
Differential
Input
Differential
Input
Differential
Input
Differential
Input
3.3V CMOS
Input
3.3V CMOS
Power
0V
MIPI CSI differential data2
negative.
MIPI CSI differential data2
positive.
MIPI CSI differential data1
negative.
MIPI CSI differential data1
positive.
MIPI CSI differential data0
negative.
MIPI CSI differential data0
positive.
MIPI CSI differential clock
negative.
MIPI CSI differential clock
positive.
Ground.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 149 of 168
Generic Qseven Carrier Board Hardware User Guide
17
18
GND
DI0_PIN15
GND
Connected to 45th Pin of
Expansion Connector 2
Connected to 43rd Pin of
Expansion Connector 2
Connected to 44th Pin of
Expansion Connector 2
Connected to 41st Pin of
Expansion Connector 2
Connected to 42nd Pin of
Expansion Connector 2
Connected to 39th Pin of
Expansion Connector 2
Connected to 40th Pin of
Expansion Connector 2
Connected to 37th Pin of
Expansion Connector 2
Connected to 38th Pin of
Expansion Connector 2
Connected to 35th Pin of
Expansion Connector 2
Connected to 36th Pin of
Expansion Connector 2
GND
GND
Connected to 31st Pin of
Expansion Connector 2
Power
Output
0V
3.3V CMOS
Output
3.3V CMOS
Ground.
Parallel LCD Data Enable
(DRDY).
Parallel LCD Vsync.
19
DI0_PIN3
20
DI0_PIN2
Output
3.3V CMOS
Parallel LCD Hsync.
21
DI0_PIN4
Output
3.3V CMOS
Output
3.3V CMOS
Parallel LCD Contrast
control.
EIM Enable Byte0.
22
EIM_EB0
23
EIM_EB1
Output
3.3V CMOS
EIM Enable Byte1.
24
EIM_WAIT
Input
3.3V CMOS
EIM Ready/Busy/Wait.
25
EIM_BCLK
Output
3.3V CMOS
EIM Burst Clock.
26
27
EIM_CRE
(NANDF_CS2)
EIM_RW
Output
3.3V CMOS
EIM Memory Register Set.
Output
3.3V CMOS
EIM Read/Write Enable.
28
EIM_CS0
Output
3.3V CMOS
EIM Chip Select0.
29
30
31
GND
GND
EIM_DA15
Power
Power
Input/
Output
0V
0V
3.3V CMOS
Ground.
Ground.
EIM Data & address line 15.
32
EIM_DA14
Connected to 32nd Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 14.
33
EIM_DA13
Connected to 29th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 13.
34
EIM_DA12
Connected to 30th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 12.
35
EIM_DA11
Connected to 27th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 11.
36
EIM_DA10
Connected to 28th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 10.
37
EIM_DA9
Connected to 25th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 9.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 150 of 168
Generic Qseven Carrier Board Hardware User Guide
38
EIM_DA8
Connected to 26th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 8.
39
EIM_DA7
Connected to 23rd Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 7.
40
EIM_DA6
Connected to 24th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 6.
41
EIM_DA5
Connected to 21st Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 5.
42
EIM_DA4
Connected to 22nd Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 4.
43
EIM_DA3
Connected to 19th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 3.
44
EIM_DA2
Connected to 20th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 2.
45
EIM_DA1
Connected to 17th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 1.
46
EIM_DA0
Connected to 18th Pin of
Expansion Connector 2
Input/
Output
3.3V CMOS
EIM Data & address line 0.
47
48
49
GND
GND
DISP0_DAT20
Power
Power
Output
0V
0V
3.3V CMOS
50
DISP0_DAT19
Output
3.3V CMOS
51
DISP0_DAT21
Output
3.3V CMOS
52
DISP0_DAT16
Output
3.3V CMOS
53
DISP0_DAT2
Output
3.3V CMOS
54
Output
3.3V CMOS
Ground.
Ground.
Parallel LCD Data20 (Red
Data4).
Parallel LCD Data19 (Red
Data3).
Parallel LCD Data21 (Red
Data5).
Parallel LCD Data16 (Red
Data0).
Parallel LCD Data2 (Blue
Data2).
PWM2 output.
55
PWM2_PWM
O(GPIO_1)
DISP0_DAT1
Output
3.3V CMOS
56
57
GND
DSI_D0M
Power
Output
0V
Differential
58
DISP0_DAT11
Output
3.3V CMOS
59
DSI_D0P
GND
GND
Connected to 35th Pin of
Expansion Connector 1
Connected to 36th Pin of
Expansion Connector 1
Connected to 33rd Pin of
Expansion Connector 1
Connected to 34th Pin of
Expansion Connector 1
Connected to 41st Pin of
Expansion Connector 1
Connected to 19th Pin of
Expansion Connector 1
Connected to 43rd Pin of
Expansion Connector 1
GND
Connected to 58th Pin of
Expansion Connector 1
Connected to 38th Pin of
Expansion Connector 1
Connected to 56th Pin of
Output
Differential
iWave Systems Technologies Pvt. Ltd.
Parallel LCD Data1 (Blue
Data1).
Ground.
MIPI DSI differential data
negative.
Parallel LCD Data11 (Green
Data3).
MIPI DSI differential data
Rev 2.2
Page 151 of 168
Generic Qseven Carrier Board Hardware User Guide
60
DSI_CLK0M
61
62
63
GND
GND
DSI_CLK0P
64
DISP0_DAT13
65
DISP0_DAT4
66
DISP0_DAT10
67
DISP0_DAT3
68
DISP0_DAT0
69
DISP0_DAT5
70
DISP0_DAT7
71
DISP0_DAT9
72
DISP0_DAT12
73
DISP0_DAT14
74
DISP0_DAT17
75
CAN2_TX
(KEY_COL4)
CAN2_RX
(KEY_ROW4)
DI0_DISP_CLK
76
77
78
79
80
81
ESAI_HCKT
(ENET_RXD0)
GND
GND
SPDIF_OUT1
(GPIO_19)
Expansion Connector 1
Connected to 57th Pin of
Expansion Connector 1
GND
GND
Connected to 55th Pin of
Expansion Connector 1
Connected to 31st Pin of
Expansion Connector 1
Connected to 30th Pin of
Expansion Connector 1
Connected to 29th Pin of
Expansion Connector 1
Connected to 28th Pin of
Expansion Connector 1
Connected to 26th Pin of
Expansion Connector 1
Connected to 25th Pin of
Expansion Connector 1
Connected to 24th Pin of
Expansion Connector 1
Connected to 23rd Pin of
Expansion Connector 1
Connected to 22nd Pin of
Expansion Connector 1
Connected to 21st Pin of
Expansion Connector 1
Connected to 20th Pin of
Expansion Connector 1
Connected to 79th Pin of
Expansion Connector 1
Connected to 78th Pin of
Expansion Connector 1
Connected to 77th Pin of
Expansion Connector 1
Connected to 18th Pin of
Expansion Connector 1
GND
GND
Connected to 17th Pin of
Expansion Connector 1
Output
Differential
Power
Power
Output
0V
0V
Differential
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Output
3.3V CMOS
Input
3.3V CMOS
Positive.
MIPI DSI differential clock
negative.
Ground.
Ground.
MIPI DSI differential clock
positive.
Parallel LCD Data13 (Green
Data5).
Parallel LCD Data4 (Blue
Data 4).
Parallel LCD Data10 (Green
Data2.)
Parallel LCD Data3 (Blue
Data 3).
Parallel LCD Data0 (Blue
Data0).
Parallel LCD Data5 (Blue
Data5).
Parallel LCD Data7 (Blue
Data7).
Parallel LCD Data9 (Green
Data1).
Parallel LCD Data12 (Green
Data4).
Parallel LCD Data14 (Green
Data6).
Parallel LCD Data17 (Red
Data1).
CAN channel2 Transmit
line.
CAN channel2 Receive line.
Output
3.3V CMOS
Parallel LCD Clock.
Input/
Output
Power
Power
Output
3.3V CMOS
ESAI High Frequency Clock
for Transmitter.
Ground.
Ground.
SPDIF output line.
iWave Systems Technologies Pvt. Ltd.
0V
0V
3.3V CMOS
Rev 2.2
Page 152 of 168
Generic Qseven Carrier Board Hardware User Guide
82
83
84
85
86
87
88
89
90
91
92
93
94
95
ESAI_FST
(ENET_RXD1)
SPDIF_IN1
(GPIO_16)
Connected to 16th Pin of
Expansion Connector 1
Connected to 15th Pin of
Expansion Connector 1
Input/
Output
Input
3.3V CMOS
ESAI_SCKT(EN
ET_CRS_DV)
ESAI_TX0
(GPIO_17)
PWM2_PWM
O(GPIO_1)
ESAI_TX1
(GPIO_18)
ESAI_HCKR
(GPIO_3)
ESAI_TX3_RX2
(ENET_TX_EN)
ESAI_FSR
(GPIO_9)
ESAI_TX2_RX3
(ENET_TXD1)
DISP0_DAT18
Connected to 14th Pin of
Expansion Connector 1
Connected to 13th Pin of
Expansion Connector 1
Connected to 12th Pin of
Expansion Connector 1
Connected to 11th Pin of
Expansion Connector 1
Connected to 10th Pin of
Expansion Connector 1
Connected to 9th Pin of
Expansion Connector 1
Connected to 8th Pin of
Expansion Connector 1
Connected to 7th Pin of
Expansion Connector 1
Connected to 6th Pin of
Expansion Connector 1
Connected to 5th Pin of
Expansion Connector 1
Connected to 4th Pin of
Expansion Connector 1
Connected to 3rd Pin of
Expansion Connector 1
Connected to 2nd Pin of
Expansion Connector 1
GND
GND
Connected to 48th Pin of
Expansion Connector 1
Connected to 47th Pin of
Expansion Connector 1
Connected to 46th Pin of
Expansion Connector 1
Connected to 45th Pin of
Expansion Connector 1
GND
Input/
Output
Output
3.3V CMOS
3.3V CMOS
ESAI Transmitter Serial
Clock.
ESAI Serial Transmit0 Data.
Output
3.3V CMOS
PWM2 Output.
Output
3.3V CMOS
ESAI Serial Transmit1 Data.
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Output
3.3V CMOS
General Purpose Pin 3.
3.3V CMOS
ESAI Serial
Transmit3/Receive2 Data.
General Purpose Pin 9.
Input/
Output
Output
3.3V CMOS
Input/
Output
Output
3.3V CMOS
Power
Power
Output
0V
0V
Differential
Output
3.3V CMOS
Output
Differential
Output
3.3V CMOS
Power
0V
ESAI_TX4_RX1
(ENET_TXD0)
DISP0_DAT22
96
ESAI_TX5_RX0
(GPIO_8)
DISP0_DAT23
97
98
99
GND
GND
DSI_D1M
100 DISP0_DAT15
101 DSI_D1P
102 DISP0_DAT8
103 GND
iWave Systems Technologies Pvt. Ltd.
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
ESAI Frame Sync for
Transmitter.
SPDIF input line.
ESAI Serial
Transmit2/Receive3 Data.
LCD Data 18 (Red Data 2).
ESAI Serial
Transmit4/Receive1 Data.
LCD Data 22 (Red Data 6).
ESAI Serial
Transmit5/Receive0 Data.
LCD Data 23 (Red Data 7).
Ground.
Ground.
MIPI DSI differential data1
negative.
Parallel LCD Data15 (Green
Data7).
MIPI DSI differential data1
positive.
Parallel LCD Data8 (Green
Data0).
Ground.
Rev 2.2
Page 153 of 168
Generic Qseven Carrier Board Hardware User Guide
104 GND
105 NC
106 NC
107 NC
108 NC
109 GND
110 GND
111 NC
112 USB_4_5_OC
113 NC
114 NC
115
116
117
118
119
120
GND
GND
Power
Power
Power
Power
GND
Connected to 75th Pin of
Qseven Edge Connector
Connected to 76th Pin of
Qseven Edge Connector
Connected to 77th Pin of
Qseven Edge Connector
Connected to 78th Pin of
Qseven Edge Connector
GND
GND
Connected to 81st Pin of
Qseven Edge Connector
Connected to 80th Pin of
Qseven Edge Connector
Connected to 83rd Pin of
Qseven Edge Connector
Connected to 79th Pin of
Qseven Edge Connector
GND
GND
VCC_5V
VCC_5V
VCC_5V
VCC_5V
Power
NC
0V
NC
Ground.
No Connection.
NC
NC
No Connection.
NC
NC
No Connection.
NC
NC
No Connection.
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
Input
3.3V CMOS
NC
NC
Over current sense for USB
port 4 & 5.
No Connection.
NC
NC
No Connection.
Power
Power
Power
Power
Power
Power
0V
0V
5V
5V
5V
5V
Ground.
Ground.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 154 of 168
Generic Qseven Carrier Board Hardware User Guide
6.2
Expansion Pin-out based on AM389x SOM
Table 51: Carrier Board Expansion Connector pin-out based on AM389x SOM
Pin
No
1
2
3
Pin Name
based on
AM389x SOM
GND
GND
NC
4
Pin Connection
Signal
Type
Voltage Level/
Termination
Description
GND
GND
Connected to 80th Pin of
Expansion Connector 2
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
NC
Connected to 79th Pin of
Expansion Connector 2
NC
NC
No Connection.
5
GND
Power
0V
Ground.
6
GND
Power
0V
Ground.
7
GND
Power
0V
Ground.
8
RFOUT
Connected to 72nd Pin of
Expansion Connector 2
Connected to 68th Pin of
Expansion Connector 2
Connected to 64th Pin of
Expansion Connector 2
Connected to 75th Pin of
Expansion Connector 2
Analog
3.3V
RF Out Analog Signal.
9
IOUTG
Connected to 73rd Pin of
Expansion Connector 2
Analog
3.3V
TV Out Analog Signal.
10
NC
Connected to 71st Pin of
Expansion Connector 2
NC
NC
No Connection.
11
IOUTD
Connected to 69th Pin of
Expansion Connector 2
Analog
3.3V
TV Out Analog Signal.
12
NC
NC
NC
No Connection.
13
IOUTE
Analog
3.3V
TV Out Analog Signal.
14
NC
NC
NC
No Connection.
15
IOUTF
Analog
3.3V
TV Out Analog Signal.
16
17
18
GND
GND
MDIO_MDCLK
Power
Power
Output
0V
0V
3.3V
Ground.
Ground.
Ethernet Clock.
19
EMAC1_TXD4
Connected to 67th Pin of
Expansion Connector 2
Connected to 65th Pin of
Expansion Connector 2
Connected to 63rd Pin of
Expansion Connector 2
Connected to 61st Pin of
Expansion Connector 2
GND
GND
Connected to 45th Pin of
Expansion Connector 2
Connected to 43rd Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 4.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 155 of 168
Generic Qseven Carrier Board Hardware User Guide
20
21
22
23
24
25
26
27
28
29
30
31
Connected to 44th Pin of
Expansion Connector 2
Connected to 41st Pin of
Expansion Connector 2
EMAC1_RXD0 Connected to 42nd Pin of
Expansion Connector 2
EMAC1_TXD7 Connected to 39th Pin of
Expansion Connector 2
EMAC1_RXD2 Connected to 40th Pin of
Expansion Connector 2
EMAC1_TXD5 Connected to 37th Pin of
Expansion Connector 2
EMAC1_RXDV Connected to 38th Pin of
Expansion Connector 2
EMAC1_TXEN Connected to 35th Pin of
Expansion Connector 2
MDIO_MDIO
Connected to 36th Pin of
Expansion Connector 2
GND
GND
GND
GND
EMAC1_RXCLK Connected to 31st Pin of
Expansion Connector 2
EMAC1_GMTC
LK
MCA1_AXR0
Output
3.3V
Ethernet Clock.
Input
3.3V
McASP Audio Port1.
Input
3.3V
Ethernet Receive Data 0.
Output
3.3V
Ethernet Transmit Data 7.
Input
3.3V
Ethernet Receive Data 2.
Output
3.3V
Ethernet Transmit Data 5.
Input
3.3V
Output
3.3V
Ethernet Receive Data
Valid Input.
Ethernet Transmit Enable.
Input/
Output
Power
Power
Input
3.3V
Ethernet MDIO.
0V
0V
3.3V
Ground.
Ground.
Ethernet Receive Clock.
32
EMAC1_RXD6
Connected to 32nd Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 6.
33
EMAC1_RXD5
Connected to 29th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 5.
34
EMAC1_TXD6
Connected to 30th Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 6.
35
EMAC1_RXD1
Connected to 27th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 1.
36
EMAC1_RXD4
Connected to 28th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 4.
37
EMAC1_COL
Connected to 25th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Column.
38
EMAC1_TXCLK
Connected to 26th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Transmit Clock.
39
EMAC1_RXD3
Connected to 23rd Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 3.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 156 of 168
Generic Qseven Carrier Board Hardware User Guide
40
EMAC1_TXD3
Connected to 24th Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 3.
41
EMAC1_RXD7
Connected to 21st Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Data 7.
42
EMAC1_TXD2
Connected to 22nd Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 2.
43
EMAC1_CRS
Connected to 19th Pin of
Expansion Connector 2
Input
3.3V
Ethernet CRS.
44
EMAC1_TXD1
Connected to 20th Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 1.
45
EMAC1_RXER
Connected to 17th Pin of
Expansion Connector 2
Input
3.3V
Ethernet Receive Error.
46
EMAC1_TXD0
Connected to 18th Pin of
Expansion Connector 2
Output
3.3V
Ethernet Transmit Data 0.
47
48
49
GND
GND
VIN[0]A_D[10]
GND
GND
Connected to 35th Pin of
Expansion Connector 1
Power
Power
Input
0V
0V
3.3V
50
VIN[0]A_D[12]
Connected to 36th Pin of
Expansion Connector 1
Input
3.3V
51
VIN[0]A_D[9]
Connected to 33rd Pin of
Expansion Connector 1
Input
3.3V
52
VIN[0]A_D[11]
Connected to 34th Pin of
Expansion Connector 1
Input
3.3V
53
GP0[27]
TIM7_OUT
Input/
Output
Output
3.3V
54
3.3V
PMW output.
55
General Purpose Pin 19.
0V
3.3V
Ground.
General Purpose Pin 18.
58
GP1[22]
3.3V
General Purpose Pin 22.
59
GP0[7]
3.3V
General Purpose Pin 7.
60
GP1[21]
Input/
Output
Power
Input/
Output
Input/
Output
Input/
Output
Input/
Output
3.3V
56
57
UART0_RINn/
GP1[19]
GND
GP0[18]
Connected to 41st Pin of
Expansion Connector 1
Connected to 19th Pin of
Expansion Connector 1
Connected to 43rd Pin of
Expansion Connector 1
GND
Connected to 58th Pin of
Expansion Connector 1
Connected to 38th Pin of
Expansion Connector 1
Connected to 56th Pin of
Expansion Connector 1
Connected to 57th Pin of
Expansion Connector 1
Ground.
Ground.
Video Input 0 Port A data
input 10.
Video Input 0 Port A data
input 12.
Video Input 0 Port A data
input 9.
Video Input 0 Port A data
input 11.
General Purpose Pin 27.
3.3V
General Purpose Pin 21.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 157 of 168
Generic Qseven Carrier Board Hardware User Guide
61
62
63
GND
GND
GP1[20]
GND
GND
Connected to 55th Pin of
Expansion Connector 1
Connected to 31st Pin of
Expansion Connector 1
Connected to 30th Pin of
Expansion Connector 1
Connected to 29th Pin of
Expansion Connector 1
Connected to 28th Pin of
Expansion Connector 1
Connected to 26th Pin of
Expansion Connector 1
Connected to 25th Pin of
Expansion Connector 1
Connected to 24th Pin of
Expansion Connector 1
Connected to 23rd Pin of
Expansion Connector 1
Connected to 22nd Pin of
Expansion Connector 1
Connected to 21st Pin of
Expansion Connector 1
Connected to 20th Pin of
Expansion Connector 1
Connected to 79th Pin of
Expansion Connector 1
Power
Power
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input
0V
0V
3.3V
Ground.
Ground.
General Purpose Pin 20.
64
GP0[26]
3.3V
General Purpose Pin 26.
65
71
UART0_DTRn/
GP1[16]
UART0_RTSn/
GP1[27]
UART0_DCD/
GP1[18]
UART0_CTSn/
GP1[28]
SATA_ACT1#/
GP1[31]
UART0_DSRn/
GP1[17]
GP1[29]
3.3V
General Purpose Pin 16.
3.3V
General Purpose Pin 27.
3.3V
General Purpose Pin 18.
3.3V
General Purpose Pin 28.
3.3V
General Purpose Pin 31.
3.3V
General Purpose Pin 17.
3.3V
General Purpose Pin 29.
72
GP0[6]
3.3V
General Purpose Pin 6.
73
GP0[15]
3.3V
General Purpose Pin 15.
74
75
MCA0_
AMUTE
NC
3.3V
McASP Audio Port 0 Mute.
NC
NC
No Connection.
76
NC
Connected to 78th Pin of
Expansion Connector 1
NC
NC
No Connection.
77
VIN[0]A_D[8]
Connected to 77th Pin of
Expansion Connector 1
Input
3.3V
78
MCA0_AHCLK
X
Connected to 18th Pin of
Expansion Connector 1
Input
3.3V
Video Input 0 Port A data
input 8.
McASP Audio Port Clock.
79
80
81
GND
GND
GP0[8]
Ground.
Ground.
General Purpose Pin 8.
MCA0_AFSX
Power
Power
Input/
Output
Input
0V
0V
3.3V
82
GND
GND
Connected to 17th Pin of
Expansion Connector 1
Connected to 16th Pin of
Expansion Connector 1
3.3V
McASP Audio Port.
66
67
68
69
70
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 158 of 168
Generic Qseven Carrier Board Hardware User Guide
Connected to 15th Pin of
Expansion Connector 1
Connected to 14th Pin of
Expansion Connector 1
Connected to 13th Pin of
Expansion Connector 1
Input/
Output
Input
3.3V
General Purpose Pin 24.
3.3V
McASP Audio Port Clock.
Input
3.3V
MCA0_ACLKR
Connected to 12th Pin of
Expansion Connector 1
Input
3.3V
87
MCA0_AXR1
Connected to 11th Pin of
Expansion Connector 1
Input
3.3V
88
Connected to 10th Pin of
Expansion Connector 1
Connected to 9th Pin of
Expansion Connector 1
Input
3.3V
89
MCA0_AHCLK
R
MCA0_AXR2
McASP Audio Port Receive
0.
McASP Audio Port Receive
Clock.
McASP Audio Port Receive
1.
McASP Audio Port Clock.
Input
3.3V
90
MCA0_AFSR
Input
3.3V
91
MCA0_AXR3
Connected to 8th Pin of
Expansion Connector 1
Connected to 7th Pin of
Expansion Connector 1
Input
3.3V
92
NC
NC
NC
93
MCA0_AXR4
Connected to 6th Pin of
Expansion Connector 1
Connected to 5th Pin of
Expansion Connector 1
Input
3.3V
94
UART0_RXD
Connected to 4th Pin of
Expansion Connector 1
Input
3.3V
95
MCA0_AXR5
Connected to 3rd Pin of
Expansion Connector 1
Input
3.3V
96
UART0_TXD
Connected to 2nd Pin of
Expansion Connector 1
Output
3.3V
97
98
99
GND
GND
NC
GND
GND
Connected to 48th Pin of
Expansion Connector 1
Connected to 47th Pin of
Expansion Connector 1
Power
Power
NC
0V
0V
NC
Input
3.3V
101 VIN[0]A_D[14]
Connected to 46th Pin of
Expansion Connector 1
Input
3.3V
102 VIN[0]A_D[13]
Connected to 45th Pin of
Expansion Connector 1
Input
3.3V
83
GP0[24]
84
MCA0_ACLKX
85
MCA0_AXR0
86
100 VIN[0]A_D[15]
iWave Systems Technologies Pvt. Ltd.
McASP Audio Port Receive
2.
McASP Audio Port.
McASP Audio Port Receive
3.
No Connection.
McASP Audio Port Receive
4.
UART 0 Receive Data
Signal.
McASP Audio Port Receive
5.
UART 0 Transmit Data
Signal.
Ground.
Ground.
No Connection.
Video Input 0 Port A data
input 15.
Video Input 0 Port A data
input 14.
Video Input 0 Port A data
input 13.
Rev 2.2
Page 159 of 168
Generic Qseven Carrier Board Hardware User Guide
103 GND
104 GND
105 NC
106 NC
107 NC
108 NC
109 GND
110 GND
111 NC
112 USB_4_5_OC#
113 NC
114 NC
115
116
117
118
119
120
GND
GND
Power
Power
Power
Power
GND
GND
Connected to 75th Pin of
Qseven Edge Connector
Connected to 76th Pin of
Qseven Edge Connector
Connected to 77th Pin of
Qseven Edge Connector
Connected to 78th Pin of
Qseven Edge Connector
GND
GND
Connected to 81st Pin of
Qseven Edge Connector
Connected to 80th Pin of
Qseven Edge Connector
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
NC
NC
No Connection.
NC
NC
No Connection.
NC
NC
No Connection.
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
Input
3.3V CMOS
Connected to 83rd Pin of
Qseven Edge Connector
Connected to 79th Pin of
Qseven Edge Connector
GND
GND
VCC_5V
VCC_5V
VCC_5V
VCC_5V
NC
NC
Over current sense for USB
port 4 & 5.
No Connection.
NC
NC
No Connection.
Power
Power
Power
Power
Power
Power
0V
0V
5V
5V
5V
5V
Ground.
Ground.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 160 of 168
Generic Qseven Carrier Board Hardware User Guide
6.3
Expansion Pin-out based on i.MX51 SOM
Table 52: Carrier Board Expansion Connector pin-out based on i.MX51 SOM
Pin
No
1
2
3
Pin Name
based on
i.MX51 SOM
GND
GND
VBAT
4
VBAT
5
GND
6
GND
7
GND
8
ADIN5
9
ADIN6
10
ADIN7
11
DI1_PIN12
12
PWRON3
13
PWGTDRIV1
14
PWGTDRIV2
15
CLK32K
16
17
18
GND
GND
AUD6_TXC
19
AUD6_TXFS
Pin Connection
GND
GND
Connected to 80th Pin of
Expansion Connector 2
Connected to 79th Pin of
Expansion Connector 2
Connected to 72nd Pin of
Expansion Connector 2
Connected to 68th Pin of
Expansion Connector 2
Connected to 64th Pin of
Expansion Connector 2
Connected to 75th Pin of
Expansion Connector 2
Connected to 73rd Pin of
Expansion Connector 2
Connected to 71st Pin of
Expansion Connector 2
Connected to 69th Pin of
Expansion Connector 2
Connected to 67th Pin of
Expansion Connector 2
Connected to 65th Pin of
Expansion Connector 2
Connected to 63rd Pin of
Expansion Connector 2
Connected to 61st Pin of
Expansion Connector 2
GND
GND
Connected to 45th Pin of
Expansion Connector 2
Connected to 43rd Pin of
Expansion Connector 2
Signal
Type
Voltage Level/
Termination
Description
Power
Power
Power
0V
0V
4.7V
Ground.
Ground.
PMIC Battery Power Input.
Power
4.7V
PMIC Battery Power Input.
Power
0V
Ground.
Power
0V
Ground.
Power
0V
Ground.
Analog
Analog
Analog
Analog
Analog
Analog
Input
2.75V
PMIC Analog to Digital
Convertor input 5.
PMIC Analog to Digital
Convertor input6.
PMIC Analog to Digital
Convertor input7.
Digital Input Pin 12.
Output
3.3V
Input
4.7V
Power ON/OFF button
connection.
Power Gate Driver 1.
Input
4.7V
Power Gate Driver 2.
Output
3.3V
Power
Power
Output
0V
0V
1.8V
32KHz clock output for
peripherals.
Ground.
Ground.
Audio Transmit Clock.
Output
1.8V
Audio Transmit Frame.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 161 of 168
Generic Qseven Carrier Board Hardware User Guide
Connected to 44th Pin of
Expansion Connector 2
Connected to 41st Pin of
Expansion Connector 2
Connected to 42nd Pin of
Expansion Connector 2
Connected to 39th Pin of
Expansion Connector 2
Connected to 40th Pin of
Expansion Connector 2
Connected to 37th Pin of
Expansion Connector 2
Connected to 38th Pin of
Expansion Connector 2
Connected to 35th Pin of
Expansion Connector 2
Connected to 36th Pin of
Expansion Connector 2
GND
GND
Connected to 31st Pin of
Expansion Connector 2
20
AUD6_TXD
21
AUD6_RXD
22
EIM_EB0
23
EIM_EB1
24
EIM_WAIT
25
EIM_BCLK
26
EIM_CRE
27
EIM_RW
28
EIM_CS0
29
30
31
GND
GND
EIM_DA15
32
EIM_DA14
Connected to 32nd Pin of
Expansion Connector 2
33
EIM_DA13
Connected to 29th Pin of
Expansion Connector 2
34
EIM_DA12
Connected to 30th Pin of
Expansion Connector 2
35
EIM_DA11
Connected to 27th Pin of
Expansion Connector 2
36
EIM_DA10
Connected to 28th Pin of
Expansion Connector 2
37
EIM_DA9
Connected to 25th Pin of
Expansion Connector 2
38
EIM_DA8
Connected to 26th Pin of
Expansion Connector 2
39
EIM_DA7
Connected to 23rd Pin of
Expansion Connector 2
Output
1.8V
Audio Transmit.
Input
1.8V
Audio Receive.
Output
1.8V
EIM Enable Byte0.
Output
1.8V
EIM Enable Byte1.
Input
1.8V
EIM Ready/Busy/Wait.
Output
1.8V
EIM Burst Clock.
Output
1.8V
EIM Memory Register Set.
Output
1.8V
EIM Read/Write Enable.
Output
1.8V
EIM Chip Select0.
Power
Power
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
0V
0V
1.8V
Ground.
Ground.
EIM Data & address line 15.
1.8V
EIM Data & address line 14.
1.8V
EIM Data & address line 13.
1.8V
EIM Data & address line 12.
1.8V
EIM Data & address line 11.
1.8V
EIM Data & address line 10.
1.8V
EIM Data & address line 9.
1.8V
EIM Data & address line 8.
1.8V
EIM Data & address line 7.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 162 of 168
Generic Qseven Carrier Board Hardware User Guide
40
EIM_DA6
Connected to 24th Pin of
Expansion Connector 2
41
EIM_DA5
Connected to 21st Pin of
Expansion Connector 2
42
EIM_DA4
Connected to 22nd Pin of
Expansion Connector 2
43
EIM_DA3
Connected to 19th Pin of
Expansion Connector 2
44
EIM_DA2
45
1.8V
EIM Data & address line 6.
1.8V
EIM Data & address line 5.
1.8V
EIM Data & address line 4.
1.8V
EIM Data & address line 3.
Connected to 20th Pin of
Expansion Connector 2
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
1.8V
EIM Data & address line 2.
EIM_DA1
Connected to 17th Pin of
Expansion Connector 2
Input/
Output
1.8V
EIM Data & address line 1.
46
EIM_DA0
Connected to 18th Pin of
Expansion Connector 2
Input/
Output
1.8V
EIM Data & address line 0.
47
48
49
GND
GND
AI_BCLK
Power
Power
Output
0V
0V
3.3V
Ground.
Ground.
Audio Input Bit Clock.
50
AI_DATA
Output
3.3V
Audio Input Data.
51
AI_MCLK
Output
3.3V
Audio Input Master Clock.
52
AI_LRCK
Output
3.3V
Audio Input Clock.
53
TS_INT#
Input
3.3V
Touch Interrupt.
54
Input
3.3V
General Purpose PWM.
55
B_PWM2_
OUT
B_GPIO21
General Purpose Pin 21.
GND
B_GPIO34
0V
3.3V
Ground.
General Purpose Pin 34.
58
B_GPIO20
3.3V
General Purpose Pin 20.
59
B_GPIO32
3.3V
General Purpose Pin 32.
60
B_GPIO33
3.3V
General Purpose Pin 33.
61
GND
Input/
Output
Power
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Power
3.3V
56
57
GND
GND
Connected to 35th Pin of
Expansion Connector 1
Connected to 36th Pin of
Expansion Connector 1
Connected to 33rd Pin of
Expansion Connector 1
Connected to 34th Pin of
Expansion Connector 1
Connected to 41st Pin of
Expansion Connector 1
Connected to 19th Pin of
Expansion Connector 1
Connected to 43rd Pin of
Expansion Connector 1
GND
Connected to 58th Pin of
Expansion Connector 1
Connected to 38th Pin of
Expansion Connector 1
Connected to 56th Pin of
Expansion Connector 1
Connected to 57th Pin of
Expansion Connector 1
GND
0V
Ground.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 163 of 168
Generic Qseven Carrier Board Hardware User Guide
62
63
GND
B_GPIO31
64
B_GPIO30
65
B_GPIO29
66
B_GPIO28
67
B_GPIO27
68
B_GPIO26
69
B_GPIO25
70
B_GPIO24
71
B_GPIO23
72
B_GPIO22
73
IS1
74
IS0
75
B_GPIO19
76
B_GPIO18
77
B_GPIO17
78
B_GPIO16
79
80
81
GND
GND
B_GPIO15
82
B_GPIO14
83
B_GPIO13
GND
Connected to 55th Pin of
Expansion Connector 1
Connected to 31st Pin of
Expansion Connector 1
Connected to 30th Pin of
Expansion Connector 1
Connected to 29th Pin of
Expansion Connector 1
Connected to 28th Pin of
Expansion Connector 1
Connected to 26th Pin of
Expansion Connector 1
Connected to 25th Pin of
Expansion Connector 1
Connected to 24th Pin of
Expansion Connector 1
Connected to 23rd Pin of
Expansion Connector 1
Connected to 22nd Pin of
Expansion Connector 1
Connected to 21st Pin of
Expansion Connector 1
Connected to 20th Pin of
Expansion Connector 1
Connected to 79th Pin of
Expansion Connector 1
Connected to 78th Pin of
Expansion Connector 1
Connected to 77th Pin of
Expansion Connector 1
Connected to 18th Pin of
Expansion Connector 1
GND
GND
Connected to 17th Pin of
Expansion Connector 1
Connected to 16th Pin of
Expansion Connector 1
Connected to 15th Pin of
Expansion Connector 1
Power
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Power
Power
Input/
Output
Input/
Output
Input/
Output
iWave Systems Technologies Pvt. Ltd.
0V
3.3V
Ground.
General Purpose Pin 31.
3.3V
General Purpose Pin 30.
3.3V
General Purpose Pin 29.
3.3V
General Purpose Pin 28.
3.3V
General Purpose Pin 27.
3.3V
General Purpose Pin 26.
3.3V
General Purpose Pin 25.
3.3V
General Purpose Pin 24.
3.3V
General Purpose Pin 23.
3.3V
General Purpose Pin 22.
3.3V
General Purpose Pin IS1.
3.3V
General Purpose Pin IS0.
3.3V
General Purpose Pin 19.
3.3V
General Purpose Pin 18.
3.3V
General Purpose Pin 17.
3.3V
General Purpose Pin 16.
0V
0V
3.3V
Ground.
Ground.
General Purpose Pin 15.
3.3V
General Purpose Pin 14.
3.3V
General Purpose Pin 13.
Rev 2.2
Page 164 of 168
Generic Qseven Carrier Board Hardware User Guide
Connected to 14th Pin of
Expansion Connector 1
Connected to 13th Pin of
Expansion Connector 1
Connected to 12th Pin of
Expansion Connector 1
Connected to 11th Pin of
Expansion Connector 1
Connected to 10th Pin of
Expansion Connector 1
Connected to 9th Pin of
Expansion Connector 1
Connected to 8th Pin of
Expansion Connector 1
Connected to 7th Pin of
Expansion Connector 1
Connected to 6th Pin of
Expansion Connector 1
Connected to 5th Pin of
Expansion Connector 1
Connected to 4th Pin of
Expansion Connector 1
Connected to 3rd Pin of
Expansion Connector 1
Connected to 2nd Pin of
Expansion Connector 1
GND
GND
Connected to 48th Pin of
Expansion Connector 1
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Power
Power
Output
3.3V
General Purpose Pin 12.
3.3V
General Purpose Pin 11.
3.3V
General Purpose Pin 10.
3.3V
General Purpose Pin 9.
3.3V
General Purpose Pin 8.
3.3V
General Purpose Pin 7.
3.3V
General Purpose Pin 6.
3.3V
General Purpose Pin 5.
3.3V
General Purpose Pin 4.
3.3V
General Purpose Pin 3.
3.3V
General Purpose Pin 2.
3.3V
General Purpose Pin 1.
3.3V
General Purpose Pin 0.
0V
0V
3.3V
100 AO_LRCK
Connected to 47th Pin of
Expansion Connector 1
Output
3.3V
Ground.
Ground.
Audio
Output
Master
Clock.
Audio Output Clock.
101 AO_BCLK
Connected to 46th Pin of
Expansion Connector 1
Output
3.3V
Audio Output Bit Clock.
102 AO_DATA
Connected to 45th Pin of
Expansion Connector 1
Output
3.3V
Audio Output Data.
103 GND
104 GND
105 NC
GND
GND
Connected to 75th Pin of
Qseven Edge Connector
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
84
B_GPIO12
85
B_GPIO11
86
B_GPIO10
87
B_GPIO9
88
B_GPIO8
89
B_GPIO7
90
B_GPIO6
91
B_GPIO5
92
B_GPIO4
93
B_GPIO3
94
B_GPIO2
95
B_GPIO1
96
B_GPIO0
97
98
99
GND
GND
AO_MCLK
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 165 of 168
Generic Qseven Carrier Board Hardware User Guide
106 NC
107 NC
108 NC
109 GND
110 GND
111 NC
112 USB_4_5_OC#
113 NC
114 NC
115
116
117
118
119
120
GND
GND
Power
Power
Power
Power
Connected to 76th Pin of
Qseven Edge Connector
Connected to 77th Pin of
Qseven Edge Connector
Connected to 78th Pin of
Qseven Edge Connector
GND
GND
Connected to 81st Pin of
Qseven Edge Connector
Connected to 80th Pin of
Qseven Edge Connector
NC
NC
No Connection.
NC
NC
No Connection.
NC
NC
No Connection.
Power
Power
NC
0V
0V
NC
Ground.
Ground.
No Connection.
Input
3.3V CMOS
Connected to 83rd Pin of
Qseven Edge Connector
Connected to 79th Pin of
Qseven Edge Connector
GND
GND
VCC_5V
VCC_5V
VCC_5V
VCC_5V
NC
NC
Over current sense for USB
port 4 & 5.
No Connection.
NC
NC
No Connection.
Power
Power
Power
Power
Power
Power
0V
0V
5V
5V
5V
5V
Ground.
Ground.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
VCC Power Supply.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 166 of 168
Generic Qseven Carrier Board Hardware User Guide
7
7.1
APPENDIX III
iWave’s Compatible Qseven CPU Modules
Generic Qseven Carrier Board is board is compatible with the following iWave’s Qseven CPU modules.

Rainbow-G17M (Cyclone V Qseven CPU Module)
http://www.iwavesystems.com/iwave-new-cyclone-v-soc-based-som-overview

Rainbow-G15M-Q7 (i.MX6 Qseven CPU Module):
http://www.iwavesystems.com/product/cpu-modules/i-mx6-q7-som/i-mx6-qseven-som.html

Rainbow G12M-Q7 (AM389x Qseven CPU Module):
http://www.iwavesystems.com/product/cpu-modules/am389x-dm816x-som/am389x-dm816x-q7module.html

Rainbow G8M-Q7 (i.MX51 Qseven CPU Module):
http://www.iwavesystems.com/product/cpu-modules/i-mx51-q7-module/i-mx51-q7-som.html

Rainbow G6M-Q7 (Atom Qseven Module):
http://www.iwavesystems.com/product/cpu-modules/atom-z5xx-q7-som-12.html
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 167 of 168
Generic Qseven Carrier Board Hardware User Guide
8
8.1
APPENDIX IV
Debug USB Cable Connecting Procedure
Due to the hardware errata of carrier board, there is chance of Debug UART interface misbehaving if the
below Power ON and Power OFF procedure is not followed in carrier board.
While Powering On the carrier board:
 Power ON the Generic Qseven Carrier Board.
 ONLY then connect the Debug USB Cable “Type A to Micro B” between PC and carrier Board
Debug USB connector (J15).
Important Note: Make sure that the Debug USB Cable is connected only after Generic Qseven Carrier
Board Power is ON.
While Powering OFF the carrier board:
 Remove the Debug USB Cable “Type A to Micro B” between PC and carrier Board Debug USB
connector (J15).
 Power OFF the Generic Qseven Carrier Board.
Important Note: Make sure that the Debug USB Cable is removed before Generic Qseven Carrier Board
Power is OFF.
iWave Systems Technologies Pvt. Ltd.
Rev 2.2
Page 168 of 168