Model No. WEEVSY1326.0

Serial No.

Write the serial number in the space above for future reference.

Serial Number Decal (Under Seat)

QUESTIONS?

As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, please call:

08457 089 009

Or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

UK email: [email protected]

CAUTION

Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference.

USER'S MANUAL

Visit our website at www.iconeurope.com

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

WARNING DECAL PLACEMENT

The decal shown here has been placed on the weight system. If the decal is missing or illegible, call the telephone number on the front cover of this manual and order a free replacement decal. Apply the decal in the location shown.

VERTICAL WARNING

PN 218558 – Black Text/Clear Background

PN 218559 – White Text/Clear Background

WEIDER is a registered trademark of ICON IP, Inc.

2

IMPORTANT PRECAUTIONS

WARNING:

To reduce the risk of serious injury, read the following important precautions before using the weight system.

1.

Read all instructions in this manual and in the accompanying literature and all warnings on the weight system before using the weight system. Use the weight system only as described in this manual.

6.

Inspect and properly tighten all parts regularly. Replace any worn parts immediately.

7.

Keep children under the age of 12 and pets away from the weight system at all times.

2.

It is the responsibility of the owner to ensure that all users of the weight system are adequately informed of all precautions.

8.

Always wear athletic shoes for foot protection when using the weight system.

9.

Keep hands and feet away from moving parts.

3.

The weight system is intended for home use only. Do not use the weight system in a commercial, rental, or institutional setting.

10. The weight system is designed to support a maximum user weight of 300 lbs (135 kg).

4.

Keep the weight system indoors, away from moisture and dust. Place the weight system on a level surface, with a mat beneath it to protect the floor or carpet. Make sure that there is enough clearance around the weight system to mount, dismount, and use the weight system.

5.

This weight system has an open weight stack; the weight stack must not be accessible from any point outside of the user’s field of view. To prevent access to the weight stack, place the weight system in a corner or bay of a room, as shown in the drawing below. There must be no more than 3 ft. (1m) of clearance between the weight system and the adjacent walls.

11. Always stand on the foot plate when performing an exercise that could cause the weight system to tip.

12. Never release the arms, leg lever, or lat bar while weights are raised; the weights will fall with great force.

13. Always disconnect the lat bar from the weight system when performing an exercise that does not use the lat bar.

14. The weight system is designed to be used only with the included weight. Do not use the weight system with dumbbells or any other type of weight to increase the resistance.

Wall

15. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on all of the pulleys.

16. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down.

WARNING:

Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

3

BEFORE YOU BEGIN

Thank you for selecting the versatile WEIDER ® 900 weight system. The weight system offers a selection of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the weight system will help you to achieve the results you want.

al. To help us assist you, please note the product model number and serial number before contacting us.

The model number is WEEVSY1326.0. The serial number can be found on a decal attached to the weight system (see the front cover of this manual for the location of the decal).

For your benefit, read this manual carefully before

using the weight system. If you have questions after reading this manual, see the front cover of this manu-

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.

High Pulley Station

Lat Bar

Butterfly Arm/Press Arm

Backrest

Seat

Foot Plate

Press Frame Lock

ASSEMBLED DIMENSIONS:

Height: 79 in. (200 cm)

Width: 37 in. (94 cm)

Depth: 41 in. (104 cm)

Weight Stack

4

PART IDENTIFICATION CHART

M6 x 16mm

Screw (40)

M6 x 63mm Screw (67)

M6 x 58mm Screw (65)

M6 Washer (73)

M10 x 52mm Bolt (52)

M8 Washer (71)

M10 x 46mm Bolt (53)

M8 x 45mm Bolt (60)

M10 Washer (70) M6 x 43mm Bolt (61)

M6 Nylon Locknut (72)

M8 Nylon Locknut (69)

25mm Washer (29)

M10 Nylon Locknut (68)

M8 x 63mm Bolt (66)

M8 x 63mm Carriage Bolt (58)

M10 x 65mm Carriage Bolt (59)

M8 x 70mm Carriage Bolt (56)

M10 x 65mm Bolt (55)

M8 x 68mm Bolt (63)

M10 x 70mm Bolt (57)

M10 x 78mm Bolt (54)

M10 x 100mm Bolt (46)

M10 x 125mm Bolt (64)

M10 x 155mm Bolt (62)

5

M

M

ASSEMBLY

Make Things Easier for Yourself

Everything in this manual is designed to ensure that the weight system can be assembled successfully by anyone. However, it is important to realize that the versatile weight system has many parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly.

Before beginning assembly, carefully read the following information and instructions:

• Assembly requires two persons.

• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

• Tighten all parts as you assemble them, unless instructed to do otherwise.

• As you assemble the weight system, make sure all parts are oriented as shown in the drawings.

• For help identifying small parts, use the PART

IDENTIFICATION CHART.

The following tools (not included) are required for assembly:

• two adjustable spanners

• one rubber mallet

• one standard screwdriver

• one Phillips screwdriver

• lubricant, such as grease or petroleum jelly, and soapy water.

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end spanners, or a set of ratchet spanners.

FRAME ASSEMBLY

1.

Before beginning assembly, make sure that you have read and understand the information in the box above.

Orient the Stabilizer (2) as shown, with the indented holes facing downward. Attach the

Base (1) to the Stabilizer with two M10 x 65mm

Carriage Bolts (59) and two M10 Nylon

Locknuts (68). Do not tighten the Nylon

Locknuts yet.

Insert two M8 x 63mm Carriage Bolts (58) into the bottom of the Base (1). Note: It may be helpful to place tape over the bolt heads to hold them in place.

1

1

68

These holes are smaller than those on the opposite side.

2

58

Indent

59

Indent

6

2.

Attach the Upright (3) to the Base (1) with the two M8 x 63mm Carriage Bolts (58) and two

M8 Nylon Locknuts (69). Do not tighten the

Nylon Locknuts yet.

Attach the Press Frame Lock (39) to the

Upright (3) with an M8 x 63mm Bolt (66), two

M8 Washers (71), and an M8 Nylon Locknut

(69). Do not overtighten the Nylon Locknut; the Press Frame Lock must pivot easily.

2

66

39

71

71

69

3

69

1

58

69

3.

Set the two Weight Bumpers (17) over the indicated holes in the Stabilizer (2).

Orient the two Weight Guides (10) so that the indicated holes are near the lower ends. Insert the Weight Guides into the Weight Bumpers

(17) and the holes in the Stabilizer (2). Attach the Weight Guides with two M10 x 70mm Bolts

(57), two M10 Washers (70), two Small Spacers

(37), and two M10 Nylon Locknuts (68).

Tighten the M10 Nylon Locknuts (68) used in steps 1 and 3.

3

10

68

17

Holes

70

57

37

68 2

7

4.

Slide eight Weights (15) onto the Weight

Guides (10), with the slot for the Weight Pin

(not shown) on the bottom and on the side facing away from the Upright (3).

Insert the Weight Tube (12) into the Weights

(15).

Lubricate the indicated holes in a Weight (15) with grease. Slide the Weight onto the Weight

Guides (10).

4

3

10

Lubricate

15

12

15

5.

Attach the Top Frame (4) to the Upright (3) with two M8 x 68mm Bolts (63) and two M8 Nylon

Locknuts (69). Do not tighten the Nylon

Locknuts yet.

Attach the Top Frame (4) between the Weight

Guides (10) with an M10 x 155mm Bolt (62), two M10 Washers (70), and an M10 Nylon

Locknut (68).

Tighten the Nylon Locknuts (68, 69) used in steps 2 and 5.

5

6.

Attach the Seat Frame (8) to the Upright (3) with an M8 x 70mm Carriage Bolt (56) and an

M8 Knob (30).

6

4

63

3

62

70

69

10

70

68

8

56

3

30

8

ARM ASSEMBLY

7.

Apply grease to an M10 x 125mm Bolt (64).

Orient the Press Frame (5) with the bracket on the side shown. Attach the Press Frame to the

Top Frame (4) with the Bolt, two M10 Washers

(70), and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the Press

Frame must pivot easily.

7 4

64

Grease

70

5

Bracket

70

68

8.

Attach an Arm Pad (20) to the Left Butterly Arm

(7) with two M6 x 58mm Screws (65) and two

M6 Washers (73).

Apply grease to the post on top of the Left Arm

(7). Orient a 25mm x 68mm Bushing (28) with the lip in the position shown, and slide the

Bushing onto the post.

Repeat this step with the Right Butterfly Arm

(6).

8

6

28

7

Lip

Grease

20

73

65

9.

Insert the post on the Left Butterfly Arm (7) into the left hole in the Press Frame (5). Make sure that the Left Arm is behind the indicated bracket on the Press Frame.

Slide a 25mm Washer (29) onto the post on the

Left Arm (7). Attach an M6 x 43mm Bolt (61) to the post with an M6 Nylon Locknut (72). Make sure that the Nylon Locknut and the head of the Bolt are overlapping the edge of the

Washer, as shown in the inset drawing.

Press a 25mm Round Outer Cap (27) onto the post on the Left Arm (7).

Repeat this step with the Right Arm (6).

9

Post

61

6

72

5

Bracket

61

73

27

29

72

7

29

9

CABLE ASSEMBLY

10.

See the CABLE DIAGRAM on page 18 for proper cable routing.

Identify the High Cable (50). Route the threaded shaft end of the Cable up through the

Top Frame (4) and over a 90mm Pulley (34).

Attach the Pulley inside the Top Frame with an

M10 x 65mm Bolt (55), two M10 Washers (70), two Small Spacers (37), and an M10 Nylon

Locknut (68).

11. Route the High Cable (50) over a 90mm Pulley

(34) and down through the Top Frame (4).

Attach the Pulley and a Cable Trap (36) to the bracket on the Top Frame with an M10 x 52mm

Bolt (52) and an M10 Nylon Locknut (68). Make sure the Cable Trap is oriented to hold the

Cable in the groove of the Pulley.

10

11

55

34

50

70

37

37

70

68

4

50

52

34 36

68

4

12. Route the High Cable (50) under a 90mm

Pulley (34). Attach the Pulley, a Cable Trap

(36), and two Finger Guards (35) to the second set of holes from the top of the two Pulley

Plates (44) with an M10 x 52mm Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley.

12

13. Route the High Cable (50) over a 90mm Pulley

(34). Attach the Pulley and two Finger Guards

(35) to the Top Frame (4) with an M10 x 46mm

Bolt (53) and an M10 Nylon Locknut (68).

13

53

52

44

35

36

34

44

50

35

68

4

35

35

34

50

68

10

14. Attach the end of the High Cable (50) to the

Small “U”-bracket (11) with an M8 Washer (71) and an M8 Nylon Locknut (69). Note: Do not completely tighten the Nylon Locknut; it should be threaded onto the Cable so that two threads show past the Nylon Locknut, as shown in the inset drawing.

Attach the Small “U”-bracket (11) to the Weight

Tube (12) with an M8 x 45mm Bolt (60) and an

M8 Nylon Locknut (69). Do not overtighten the Nylon Locknut; the Weight Tube must pivot easily in the Small “U”-bracket.

14

15.

Identify the Press Cable (49). Slide the Cable onto the hook on the Left Arm (7).

15

69

12

50

60

11

71

69

50

11

69

Hook

49

7

16. Apply grease to an M10 x 78mm Bolt (54).

Attach a Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the

Pulley Arm must pivot easily.

Route the Press Cable (49) over a 90mm

Pulley (34). Attach the Pulley, a Cable Trap

(36), an M10 Washer (70), and two Finger

Guards (35) to the indicated side of the Pulley

Arm (38) with an M10 x 52mm Bolt (52) and an

M10 Nylon Locknut (68). Make sure that the

Cable Trap is oriented to hold the Cable in the groove of the Pulley.

17. Route the Press Cable (49) under a 90mm

Pulley (34). Attach the Pulley and two Finger

Guards (35) to the Double “U”-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon

Locknut (68).

16

17

3

54 35

36

68

34 35

70

38

52

49

68

49

34

35

35

42

53

11

18. Apply grease to an M10 x 78mm Bolt (54).

Attach a Pulley Arm (38) to the Upright (3) with the Bolt and an M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut; the

Pulley Arm must pivot easily.

Route the Press Cable (49) over a 90mm Pulley

(34). Attach the Pulley, a Cable Trap (36), an

M10 Washer (70), and two Finger Guards (35) to the indicated side of the Pulley Arm (38) with an M10 x 52mm Bolt (52) and an M10 Nylon

Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley.

18

19. Slide the end of the Press Cable (49) onto the hook on the Right Arm (6).

19

49

52

38

35

36

34

70

35

68

54

68

49

Grease

3

6

20.

Identify the Short Cable (47). Attach the eyelet on the Cable to the Base (1) with an M10 x

70mm Bolt (57), an M10 Washer (70), and an

M10 Nylon Locknut (68). Do not overtighten the Nylon Locknut.

20

68

70

1

47

57

12

21. Route the Short Cable (47) over a 90mm Pulley

(34). Attach the Pulley and two Finger Guards

(35) to the Double “U”-bracket (42) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut

(68).

21

53

35

35

42

47

34

68

22. Attach the end of the Short Cable (47) to the

“U”-bracket (43) with an M8 Washer (71) and an M8 Nylon Locknut (69). Note: Do not completely tighten the Nylon Locknut; it should be threaded onto the Cable so that two threads show past the Nylon Locknut, as shown in the inset drawing.

22

47

43

69

47

43

71

69

23.

Identify the Low Cable (48). Attach the Cable inside the Base (1) with an M10 x 65mm Bolt

(55), two M10 Washers (70), two Large

Spacers (51), and an M10 Nylon Locknut (68).

23

48

55

70

51

1

51

70

68

24. Route the Low Cable (48) over a 90mm Pulley

(34). Attach the Pulley, a Cable Trap (36), and two Finger Guards (35) to the second hole from the bottom of each Pulley Plate (44) with an

M10 x 52mm Bolt (52) and an M10 Nylon

Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley.

24

52

35

36

48

35 68

34

44

13

25. Route the Low Cable (48) under a 90mm Pulley

(34). Attach the Pulley and two Finger Guards

(35) to the bracket on the Base (1) with an M10 x 46mm Bolt (53) and an M10 Nylon Locknut

(68).

25

48

34

53

35

1

35

68

26. Route the Low Cable (48) over a 90mm Pulley

(34). Attach the Pulley, a Cable Trap (36), and two Finger Guards (35) to the lower set of holes in the “U”-bracket (43) with an M10 x 52mm

Bolt (52) and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley.

26

52 43

35

36

34

48

35

68

27. Route the Low Cable (48) under a 90mm Pulley

(34). Attach the Pulley, a Cable Trap (36), and two Guards (14) to the Upright (3) with an M10 x 100mm Bolt (46), two M10 Washers (70), and an M10 Nylon Locknut (68). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley.

27

68

70

3

14

70

48

36

34

46

14

14

SEAT ASSEMBLY

28. Attach the Backrest (18) to the Upright (3) with two M6 x 63mm Screws (67) and two M6

Washers (73).

28

Wide End

18

3

73

67

73

67

29. Orient the Seat (19) as shown, and attach it to the Seat Frame (8) with four M6 x 16mm

Screws (40).

29

Wide

End

19

8

40

40

30. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in

ADJUSTMENTS, beginning on the next page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem.

IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 18 for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TROUBLESHOOTING AND

MAINTENANCE on page 19.

15

ADJUSTMENT

This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the correct form for each exercise.

Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.

ATTACHING THE LAT BAR

Attach the Lat Bar (31) to the High Cable (50) with a

Cable Clip (33). Note: The Lat Bar can be attached to the Low Cable (not shown). Remove the Lat Bar when performing exercises that do not require it.

USING THE BUTTERFLY ARMS

To do butterfly exercises, push the Press Frame Lock

(39) to the position shown to lock the Right and Left

Butterfly Arms (6, 7). To do press arm exercises, lift the Press Frame Lock until the Right and Left

Butterfly Arms are free.

CHANGING THE WEIGHT SETTING

To change the weight setting, insert a Weight Pin (16) under the desired Weight (15) until the bent end of the Weight Pin touches the Weights. Turn the bent end downward. Note: Due to the cables and pulleys, the amount of resistance at each exercise station may vary from the weight setting. Use the

WEIGHT RESISTANCE CHART on page 17 to find the approximate amount of resistance at each weight station.

6

50

33

31

39

15

16

7

REMOVING THE SEAT

Remove the M8 Knob (30) and the M8 x 70mm

Carriage Bolt (56). Lift the Seat Frame (8) off the pin on the Upright (3).

USING THE LOW PULLEY STATION

To perform exercises that require the Low Pulley

Station, attach a Cable Clip (33) to the Low Cable

(48) and to one end of the Chain (9). Next, attach the

Chain to another Cable Clip (33) and attach the Cable

Clip to the Lat Bar (31).

56

3

31

33

8

9

33

Pin

48

30

16

WEIGHT RESISTANCE CHART

The chart below shows the approximate weight resistance at each exercise station. Weight resistance shown for the butterfly arm station is for each butterfly arm. Note: The actual resistance at each station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides.

WEIGHT

6

7

8

9

1

4

5

2

3

Note: 1 lb. = 0.454 kg

PRESS

ARM

(lbs.)

35

50

66

81

94

111

132

155

170

BUTTERFLY ARM

(lbs.)

19

28

36

45

55

69

75

84

94

HIGH

PULLEY

(lbs.)

26

38

53

68

80

98

116

127

139

LOW

PULLEY

(lbs.)

29

43

55

69

84

96

119

139

160

17

CABLE DIAGRAM

The cable diagram below shows the proper routing of the Short Cable (47), the Low Cable (48), the Press

Cable (49), and the High Cable (50). Use the diagrams to make sure that the cables have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly and damage may occur. The numbers show the correct route for each cable.

4

5

4

Press Cable (49)

2

1

High Cable (50)

1

2

3

3

Short Cable (47)

3

2

2

5

Low Cable (48)

1

5

4

3

1

18

TROUBLESHOOTING AND MAINTENANCE

TIGHTENING THE CABLES

Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened.

Slack can be removed by moving a 90mm Pulley

(34), a Cable Trap (36), and two Finger Guards (35) to a set of holes closer to the center of the two Pulley

Plates (44). Remove the M10 Nylon Locknut (68) and the M10 x 52mm Bolt (52), and reattach the Pulley,

Cable Trap, and Finger Guards to the different set of holes in the Pulley Plates.

Slack can also be removed by moving the 90mm

Pulley (34), the Cable Trap (36), and the two Finger

Guards (35) to the higher set of holes in the “U”-bracket (43). Remove the M10 Nylon Locknut (68) and the

M10 x 52mm Bolt (52), and reattach the Pulley, the

Cable Trap, and two Finger Guards to the higher set of holes in the “U”-bracket.

Finally, slack can be removed from the cables by tightening the M8 Nylon Locknut (69) attaching the Short

Cable (47) to the “U”-bracket (43). The High Cable (not shown) and the Small “U”-bracket (not shown) can be adjusted in the same manner.

Make sure that the cables are not too tight, or the

Top Weight (not shown) will be lifted off the weight stack.

52

35

36

44

35

68

34

47

35

52

43

36

34

35

71

69

68

19

NOTES

20

PART LIST—Model No. WEEVSY1326.0

R0906A

Key No.

Qty.

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

33

34

35

36

37

38

39

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

1

2

2

1

2

2

3

4

2

5

1

1

1

2

2

1

4

2

1

3

12

18

7

9

1

1

2

1

1

1

2

1

1

1

1

1

1

1

1

Description

Base

Stabilizer

Upright

Top Frame

Press Frame

Right Arm

Left Arm

Seat Frame

Chain

Weight Guide

Small “U”-bracket

Weight Tube

Weight Tube Bumper

Guard

Weight

Weight Pin

Weight Bumper

Backrest

Seat

Arm Pad

Lock Pin

Lock

25mm Round Inner Cap

45mm Square Inner Cap

25mm x 50mm Inner Cap

50mm Square Inner Cap

25mm Round Outer Cap

25mm x 68mm Bushing

25mm Washer

M8 Knob

Lat Bar

Handgrip

Cable Clip

90mm Pulley

Finger Guard

Cable Trap

Small Spacer

Pulley Arm

Press Frame Lock

Key No.

68

69

70

71

64

65

66

67

60

61

62

63

56

57

58

59

72

73

74

#

#

#

52

53

54

55

48

49

50

51

44

45

46

47

40

41

42

43

Qty.

22

8

15

4

1

2

1

4

1

2

1

2

2

2

1

3

2

–

2

6

–

–

2

2

6

4

1

2

1

1

1

1

2

2

1

1

4

2

Description

M6 x 16mm Screw

50mm Square Outer Cap

Double “U”-bracket

“U”-bracket

Pulley Plate

Butterfly Grip

M10 x 100mm Bolt

Short Cable

Low Cable

Press Cable

High Cable

Large Spacer

M10 x 52mm Bolt

M10 x 46mm Bolt

M10 x 78mm Bolt

M10 x 65mm Bolt

M8 x 70mm Carriage Bolt

M10 x 70mm Bolt

M8 x 63mm Carriage Bolt

M10 x 65mm Carriage Bolt

M8 x 45mm Bolt

M6 x 43mm Bolt

M10 x 155mm Bolt

M8 x 68mm Bolt

M10 x 125mm Bolt

M6 x 58mm Screw

M8 x 63mm Bolt

M6 x 63mm Screw

M10 Nylon Locknut

M8 Nylon Locknut

M10 Washer

M8 Washer

M6 Nylon Locknut

M6 Washer

25mm Round Thin Cap

User’s Manual

Exercise Guide

Grease Packet

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user’s manual for information about ordering replacement parts.

21

EXPLODED DRAWING A—Model No. WEEVSY1326.0

R0906A

25

73

6

49

64

26

29

27

70

61

5

28

72

70

27

29

68

28

72

26

55

70

37

50

53

37

70

68

35

34

68

35

24

61

49

7

34

34

53

36

68 4

26

65

20

73

23

24

73

74

20

65

45

45

73

24

74

52

35

36

34

35

44

36

34

44

35

35

68

19

56

8

30

52

43

35 36

34

35

47

71

69

68

24

40

40

22

5

8

4

EXPLODED DRAWING B—Model No. WEEVSY1326.0

R0906A

32

31

33

62

70

70

68

38

35

36

34

52

35

68

26

54 63

69

68

70

39

66

71

25

71

69

18

54 35 36

38

68

68

70

34 35

52

67

73

73 67

3

53

68

42

35

34

35

68

53

35

70

69

68

48

69

35

14

70

34

14

46

36

34

1

55

53

35

34

68

68

70

70

51

48

51

35

68

70

68

68

47

57

58

9

23

32

33

41

17

2

15

59

21

22

71

69

50

69

10

12

13

60

11

37

70

70

57

41

16

ORDERING REPLACEMENT PARTS

To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

UK

Tel:

08457 089 009

Outside the UK: 0 (044) 113 387 7133

Fax: 0 (044) 113 387 7125

Please provide the following information when ordering replacement parts:

• the MODEL NUMBER of the product (WEEVSY1326.0)

• the NAME of the product (WEIDER 900 weight system)

• the SERIAL NUMBER of the product (see the front cover of this manual)

• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on pages 21 to 23)

Part No. 242331 R0906A Printed in China © 2006 ICON IP, Inc.