Zebra TC75x User manual
Reklaam
Reklaam
TC70x/TC75x
MN-002881-03
Touch Computer
User Guide for Android™ Version 6.0.1
TC70X/TC75X
USER GUIDE FOR ANDROID VERSION 6.0.1
MN-002881-03
Rev. A
February 2017
ii TC70x/TC75x User Guide for Android Version 6.0.1
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra Technologies
Corporation, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.
Revision History
Changes to the original guide are listed below:
Change
-01 Rev. A
-02 Rev A
-03 Rev A
Date
12/2016 Initial release.
12/2017 Add non-GMS software support.
2/2017 Add TC70x support.
Description
iii
iv TC70x/TC75x User Guide for Android Version 6.0.1
TABLE OF CONTENTS
Table of Contents
About This Guide
Chapter 1: Getting Started
vi TC70x/TC75x User Guide for Android Version 6.0.1
Chapter 2: Using the Device
Table of Contents vii
Chapter 3: Calls
Chapter 4: Applications
viii TC70x/TC75x User Guide for Android Version 6.0.1
Chapter 5: Data Capture
Chapter 6: Wireless
Table of Contents ix
Chapter 7: Accessories
x TC70x/TC75x User Guide for Android Version 6.0.1
Table of Contents xi
Chapter 8: Maintenance and Troubleshooting
Appendix A: Technical Specifications
xii TC70x/TC75x User Guide for Android Version 6.0.1
ABOUT THIS GUIDE
Introduction
This guide provides information about using the TC70x/TC75x touch computers and accessories.
NOTE
Screens and windows pictured in this guide are samples and can differ from actual screens.
Documentation Set
The documentation set for the TC70x and TC75x provides information for specific user needs, and includes:
•
TC70x/TC75x Touch Computer Quick Start Guide for Android Version 6.0.1 - describes how to get the device up and running.
•
TC70x/TC75x Touch Computer User Guide for Android Version 6.0.1 - describes how to use the device.
•
TC70x/TC75x Touch Computer Integrator Guide for Android Version 6.0.1 - describes how to set up the device and accessories.
Configurations
This guide covers the following configurations:
xiv TC70x/TC75x User Guide for Android Version 6.0.1
Configuration
TC700K
TC75EK
TC75FK
TC75GK
Radios Display Memory
Data Capture
Options
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High
Definition (1280 x
720) LCD
2 GB RAM/16 GB
Flash
2D imager, camera, or integrated NFC
WWAN:
HSPA+/LTE/CD
MA
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High
Definition (1280 x
720) LCD
2 GB RAM/16 GB
Flash
2D imager, camera and integrated NFC
WWAN:
HSPA+/LTE
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High
Definition (1280 x
720) LCD
2 GB RAM/16 GB
Flash
2D imager, camera and integrated NFC
WWAN:
HSPA+/LTE
WLAN: 802.11 a/b/g/n/d/h/i/r
WPAN: Bluetooth v4.0 Low Energy
4.7” High
Definition (1280 x
720) LCD
2 GB RAM/16 GB
Flash
2D imager, camera and integrated NFC
Operating
System
Android 6.0.1
Android 6.0.1
Android 6.0.1
Android 6.0.1
Software Versions
To determine the current software versions, swipe down with two fingers from the status bar to open the quick access panel and then touch .
•
Model number- Displays the model number.
•
Android version - Displays the operating system version.
•
Kernel version - Displays the kernel version number.
•
Build number - Displays the software build number.
•
Serial number - Displays the serial number.
To determine the device serial number, touch About phone > Status.
•
Serial number - Displays the serial number.
Chapter Descriptions
Topics covered in this guide are as follows:
•
provides information on getting the TC70x/TC75x up and running for the first time.
About This Guide xv
•
provides information for operating the TC70x/TC75x.
•
provides instructions for making phone calls.
•
provides information on using applications installed on the TC70x/TC75x.
•
provides information for capturing bar code data using the imager.
•
provides information on the various wireless options.
•
provides information for using the accessories for the TC70x/TC75x.
•
Chapter 8, Maintenance and Troubleshooting
includes instructions on cleaning and provides troubleshooting
solutions for potential problems during TC75x operation.
•
Appendix A, Technical Specifications
provides the technical specifications for the TC70x/TC75x.
Notational Conventions
The following conventions are used in this document:
•
Italics are used to highlight the following:
•
Chapters and sections in this and related documents
•
Bold text is used to highlight the following:
•
Dialog box, window, and screen names
•
Drop-down list and list box names
•
Check box and radio button names
•
Button names on a screen.
•
Icons on a screen.
•
Bullets (•) indicate:
•
Action items
•
Lists of alternatives
•
Lists of required steps that are not necessarily sequential
•
Sequential lists (for example, lists that describe step-by-step procedures) appear as numbered lists.
Icon Conventions
The documentation set is designed to give the reader more visual clues. The following graphic icons are used throughout the documentation set. These icons and their associated meanings are described below.
WARNING
!
The word WARNING with the associated safety icon implies information that, if disregarded, could result in death or serious injury, or serious product damage.
CAUTION
The word CAUTION with the associated safety icon implies information that, if disregarded, may result in minor or moderate injury, or serious product damage.
xvi TC70x/TC75x User Guide for Android Version 6.0.1
NOTE
NOTE contains information more important than the surrounding text, such as exceptions or preconditions. They also refer the reader elsewhere for additional information, remind the reader how to complete an action (when it is not part of the current procedure, for instance), or tell the reader where something is located on the screen. There is no warning level associated with a note.
Related Documents
•
TC70x/TC75x Touch Computer Quick Start Guide for Android Version 6.0.1, p/n MN-002879-xx.
•
TC75x Touch Computer Regulatory Guide for Android Version 6.0.1, p/n MN-002880-xx.
•
TC70x Touch Computer Regulatory Guide for Android Version 6.0.1, p/n MN-002960-xx.
•
TC70x/TC75x Touch Computer Integrator Guide for Android Version 6.0.1, p/n MN-002882-xx.
•
RS507 Hands-free Imager Product Reference Guide, p/n 72E-12082-xx.
•
DS36X8 Product Reference Guide, p/n MN-002689-xx.
•
RS6000 User Guide, MN-002704-xx.
For the latest version of this guide and all guides, go to: http://www.zebra.com/support.
Service Information
If you have a problem with the equipment, contact Customer Support in the region. Contact information is available at: http://www.zebra.com/support.
When contacting support, please have the following information available:
•
Serial number of the unit (found on manufacturing label)
•
Model number or product name (found on manufacturing label)
•
Software type and version number
•
IMEI number
About This Guide xvii
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, the user may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. Remove the SIM card and/or microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.
xviii TC70x/TC75x User Guide for Android Version 6.0.1
CHAPTER 1 GETTING STARTED
This chapter provides information for getting the device up and running for the first time.
Unpacking
1.
2.
3.
4.
Carefully remove all protective material from the TC70x/TC75x and save the shipping container for later storage and shipping.
Verify that the following were received:
•
touch computer
•
4,620 mAh PowerPercision+ Lithium-ion battery
•
Hand strap
•
Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer
Support center immediately.
Prior to using the device for the first time, remove the protective shipping film that covers the scan window, display and camera window.
1 - 2 TC70x/TC75x User Guide for Android Version 6.0.1
Features
18
17
16
15
14
13
12
1
2
3
11
10
9
4
8
5
7
6
Figure 1-1 Front View
Table 1-1 Front View Features
Number Item
1 Touch Screen
Function
Displays all information needed to operate the device.
2
3
Scan Button
PTT Button
Initiates data capture (programmable).
Initiates push-to-talk communications (programmable).
4
5
6
7
8
Back Button
Home Button
Microphone
Charging
Contacts
Speaker
Displays the previous screen.
Displays the Home screen with a single press.
On TC70x/TC75x with GMS, opens the Google Now screen when held for a short period of time.
Use for communications in Handset mode.
Provides power to the device from cables and cradles.
9 Search Button
Provides audio output for video and music playback. Provides audio in speakerphone mode.
Opens the Recent App screen.
Getting Started 1 - 3
Table 1-1 Front View Features (Continued)
Number Item
10
11
Menu Button
Light Sensor
Function
Opens a menu with items that affect the current screen or application.
Determines ambient light for controlling display backlight intensity.
12
13
14
15
16
Proximity Sensor
Power Button
Microphone
Receiver
Determines proximity for turning off display when in handset mode.
Turns the display on and off. Press and hold to reset the device, power off or swap battery. Press quickly twice when the screen is locked to open the camera application.
Use for communications in Speakerphone mode.
Use for audio playback in Handset mode.
17
18
Charging/Notificat ion LED
Data Capture
LED
Indicates battery charging status while charging and application generated notifications.
Indicates data capture status.
Front Facing
Camera
Use to take photos and videos (optional).
26
23
27
25
28
29
24
19
23
22
21
20
Figure 1-2 Rear View
Table 1-2 Back View Features
Number Item
19 Interface
Connector
Function
Provides USB host and client communications, audio and device charging via cables and accessories.
20
21
Exit Window
Microphone
Provides data capture using the imager.
Use during video recording and for noise cancellation.
1 - 4 TC70x/TC75x User Guide for Android Version 6.0.1
24
25
26
27
Table 1-2 Back View Features (Continued)
Number Item
22 Volume Up/Down
Button
Function
Increase and decrease audio volume (programmable).
23 Press to remove the battery.
28
29
Battery Release
Latches
Elastic Sleeve
Battery
Hand strap
Hand strap
Mounting Point
Camera
Camera Flash
Use to hold optional stylus.
Provides power to the device.
Use to securely hold the device in your hand.
Provides latching point for the hand strap.
Takes photos and videos.
Provides illumination for the camera.
Setup
5.
6.
7.
1.
2.
3.
4.
Perform this procedure to start using the TC70x/TC75x for the first time.
Install a SIM card (TC75x only).
Install a SAM card.
Install a micro secure digital (SD) card (optional).
Install hand strap (optional).
Install the battery.
Charge the device.
Power on the device.
Installing the SIM Card
NOTE
TC75x only.
CAUTION
For proper electrostatic discharge (ESD) precautions to avoid damaging the SIM card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
1.
NOTE
The TC75x may contain one mini SIM slot and two nano SIM slots. If using a micro SIM card, a third-party
SIM adapter is required. By default, use a nano SIM card in slot 1.
Remove access cover.
Getting Started 1 - 5 mini SIM/SAM
Slot nano SIM Slot
1 (default) nano SIM
Slot 2
Figure 1-3 TC75x SIM Slot Locations
2.
Insert a SIM card into the SIM slot with the cut edge toward the middle of the device and the contacts facing down.
Figure 1-4 nano SIM Card Installation
Figure 1-5 Mini SIM Card Installation
3.
Ensure that the SIM card is seated properly.
Installing the SAM Card
CAUTION
For proper electrostatic discharge (ESD) precautions to avoid damaging the Secure Access Module
(SAM) card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
1 - 6 TC70x/TC75x User Guide for Android Version 6.0.1
1.
2.
NOTE
The
TC70x/
TC75x contains one slot for a mini SAM card. If using a micro SAM card, a third-party adapter is required. On the TC75x. when using a SAM card, only a nano SIM card can be used.
Remove access cover.
Insert a SAM card into the SAM slot with the cut edge toward the middle of the device and the contacts facing down.
Mini SAM Slot
Figure 1-6 SAM Card Installation
3.
Ensure that the SAM card is seated properly.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
1.
2.
CAUTION
Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card. Proper
ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
Remove the hand strap, if installed.
Lift the access door.
Figure 1-7 Lift Access Door
3.
Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
Getting Started 1 - 7
Figure 1-8 Insert microSD Card in Holder
4.
Re-install the access door.
Installing the Hand Strap and Battery
NOTE
Installation of the hand strap is optional. Skip this section if not installing the hand strap.
1.
Remove the hand strap filler from the hand strap slot. Store the hand strap filler in a safe place for future replacement.
Figure 1-9 Remove Filler
2.
Insert the hand strap plate into the hand strap slot.
Figure 1-10 Insert Hand Strap
3.
Insert the battery, bottom first, into the battery compartment in the back of the TC70x/TC75x.
1 - 8 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 1-11 Insert Bottom of Battery into Battery Compartment
4.
Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 1-12 Press Down on Battery
5.
Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
Figure 1-13 Secure Hand Strap Clip
Installing the Battery
1.
Insert the battery, bottom first, into the battery compartment in the back of the TC70x/TC75x.
Getting Started 1 - 9
Figure 1-14 Insert Bottom of Battery into Battery Compartment
2.
Press the battery down into the battery compartment until the battery release latches snap into place.
Figure 1-15 Press Down on Battery
Charging the Battery
Before using the TC70x/TC75x for the first time, charge the main battery until the green Charging/Notification light emitting diode (LED) remains lit. To charge the TC70x/TC75x, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the TC70x/TC75x, see
for more information.
•
Snap-On USB Cable
•
Charging Cable Cup
•
2-Slot Charge Only Cradle
•
2-Slot USB/Ethernet Cradle
•
5-Slot Charge Only Cradle
•
5-Slot Ethernet Cradle
•
Charge Only Vehicle Cradle
•
Auto Charging Cable Cup.
•
Serial Cable Cup
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The TC70x/TC75x or accessory always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C
(+98°F)) the TC70x/TC75x or accessory may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The TC70x/TC75x or accessory indicates when charging is disabled due to abnormal temperatures via its LED.
1.
2.
To charge the main battery, connect the charging accessory to the appropriate power source.
Insert the TC70x/TC75x into a cradle or attach to a cable. The TC70x/TC75x turns on and begins charging.
The Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
1 - 10 TC70x/TC75x User Guide for Android Version 6.0.1
Charging Indicators
Table 1-3 Charging/Notification LED Charging Indicators
Off
Slow Blinking Amber (1 blink every 4 seconds)
State Indication
The device is not charging. The device is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered.
The device is charging.
Solid Green
Slow Blinking Red (1 blink every 4 seconds)
Charging complete.
Fast Blinking Amber (2 blinks/second) Charging error, e.g.:
•
Temperature is too low or too high.
•
Charging has gone on too long without completion (typically eight hours).
The device is charging but the battery is at end of useful life.
Solid Red
Fast Blinking Red (2 blinks/second)
Charging complete but the battery is at end of useful life.
Charging error but the battery is at end of useful life., e.g.:
•
Temperature is too low or too high.
•
Charging has gone on too long without completion (typically eight hours).
Google Account Setup
NOTE
Available only on devices with GMS software.
The
TC70x/
TC75x has to be connected to the internet, either through WAN (TC75x only) or Wi-Fi, in-order to set up a Google account.
The first time the TC70x/TC75x starts, the Setup Wizard displays. Follow the on-screen instructions to set up a
Google account, configure Google Wallet for purchasing items from the Play Store, entering your personal information, and enabling backup/restore features.
Replacing the Battery
CAUTION
Do not add or remove SIM, SAM or microSD card during battery replacement.
1.
2.
3.
4.
5.
Remove any accessory attached to the device.
Press the Power button until the menu appears.
Touch Battery Swap.
Follow the on-screen instructions.
Wait for the LED to turn off.
Getting Started 1 - 11
6.
If hand strap is attached, slide the hand strap clip up toward the top of the TC70x/TC75x and then lift.
Figure 1-16 Remove Hand Strap Clip
7.
Press the two battery latches in.
Figure 1-17 Press Battery Latches
8.
Lift the battery from the TC70x/TC75x.
1 - 12 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 1-18 Lift the Battery
CAUTION
Replace the battery within two minutes. After two minutes the device reboots and data may be lost.
9.
Insert the replacement battery, bottom first, into the battery compartment in the back of the TC70x/TC75x.
10.
Press the battery down until the battery release latch snaps into place.
11.
Replace the hand strap, if required.
12.
Press and hold the Power button to turn on the TC70x/TC75x.
Replacing the SIM or SAM Card
NOTE
SIM replacement applies to TC75x only.
1.
2.
3.
4.
To replace the SIM or SAM card:
Press and hold the Power button until the menu appears.
Touch Power off.
Touch OK.
If hand strap is attached, slide the hand strap clip up toward the top of the TC70x/TC75x and then lift.
Figure 1-19 Remove Hand Strap Clip
5.
6.
7.
Press the two battery latches in.
Lift the battery from the TC70x/TC75x.
Lift the access door.
Figure 1-20 Remove Access Door
8.
Remove card from holder.
Figure 1-21 Remove Mini SIM/SAM Card
Figure 1-22 Remove Nano SIM Card
Getting Started 1 - 13
1 - 14 TC70x/TC75x User Guide for Android Version 6.0.1
9.
Insert the replacement card.
Figure 1-23 Insert Mini SIM/SAM Card
Figure 1-24 Insert Nano SIM Card
10.
Replace the access door.
Figure 1-25 Replace Access Door
11.
Press the access door down and ensure that it is properly seated.
12.
Insert the battery, bottom first, into the battery compartment in the back of the TC70x/TC75x.
13.
Press the battery down until the battery release latch snaps into place.
14.
Replace the hand strap, if required.
15.
Press and hold the Power button to turn on the TC70x/TC75x.
Getting Started 1 - 15
Replacing the microSD Card
1.
2.
3.
4.
To replace the microSD card:
Press the Power button until the menu appears.
Touch Power off.
Touch OK.
If hand strap is attached, slide the hand strap clip up toward the top of the TC70x/TC75x and then lift.
Figure 1-26 Remove Hand Strap Clip
5.
6.
7.
Press the two battery latches in.
Lift the battery from the TC70x/TC75x.
Lift the access door.
Figure 1-27 Remove Access Door
8.
9.
Remove microSD card from holder.
Press the access door down and ensure that it is properly seated.
10.
Insert the replacement microSD card.
11.
Replace the access door.
Figure 1-28 Replace Access Door
12.
Insert the battery, bottom first, into the battery compartment in the back of the TC70x/TC75x.
1 - 16 TC70x/TC75x User Guide for Android Version 6.0.1
13.
Press the battery down until the battery release latch snaps into place.
14.
Replace the hand strap, if required.
15.
Press and hold the Power button to turn on the TC70x/TC75x.
Accessing Device Settings
Throughout this guide, the user can access device:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
On the Home screen, touch > .
Battery Management
NOTE
Prior to checking the battery charge level, remove the TC70x/TC75x from any AC power source (cradle or cable).
To check the charge status of the main battery, open Settings and touch About phone > Battery Information.
Battery status indicates that the battery is discharging and Battery level lists the battery charge (as a percentage of fully charged).
Monitor Battery Usage
The Battery screen lists which applications consume the most battery power. Also use it to turn off applications that were downloaded if they are consuming too much power.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
Getting Started 1 - 17
Figure 1-29 Battery Screen
The Battery screen lists the applications using the battery. The discharge graph at the top of the screen shows the rate of the battery discharge since last charged (short periods of time when connected to a charger are shown as thin green lines at the bottom of the chart), and how long it has been running on battery power.
Touch an application in the Battery screen to display details about its power consumption. Different applications display different information. Some applications include buttons that open screens with settings to adjust power use.
Low Battery Notification
When the battery charge level drops below 18%, the TC70x/TC75x displays a notice to connect the TC70x/TC75x to power.The user should charge the battery using one of the charging accessories.
Figure 1-30 Low Battery Notification
1 - 18 TC70x/TC75x User Guide for Android Version 6.0.1
When the battery charge drops below 10%, the TC70x/TC75x displays a notice to connect the TC70x/TC75x to power. The user must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the TC70x/TC75x turns off.
The user must charge the TC70x/TC75x using one of the charging accessories.
Battery Optimization
Observe the following battery saving tips:
•
Disable DataWedge Launcher profile. Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for instructions.
•
Remove Snap-on accessories when not in use.
•
Set the screen to turn off after a short period of non-use. See
Setting Screen Timeout Setting on page 1-19
•
Reduce screen brightness. See Setting the Screen Brightness.
•
Turn off all wireless radios when not in use.Note that the global positioning system (GPS) receiver is only turned on when a GPS application is using the GPS radio.
•
Turn off automatic syncing for Email, Calendar, Contacts and other applications.
•
Minimize use of applications that keep the TC70x/TC75x from suspending, for example, music, GPS and video applications.
Turning Off the Radios
To turn off all the radios:
1.
Press the Power button until the menu appears.
2.
Touch Airplane mode. The airplane icon appears in the Status bar indicating that all the radios are off.
Setting the Date and Time
The date and time is automatically synchronized using a NITZ server when the TC75x is connected to a cellular network.The user is only required to set the time zone or set the date and time when not connected to a cellular network or if the wireless LAN does not support Network Time Protocol (NTP).
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
5.
6.
Touch Automatic date & time to disable automatic date and time synchronization.
Touch Set date.
Move the sliders up and down to select the month, date and year.
Touch Done.
7.
8.
Touch Set time.
Move the sliders up and down to select the hour, minutes and part of the day.
9.
Touch Done.
10.
Touch Select time zone.
11.
Select the current time zone from the list.
Getting Started 1 - 19
12.
Touch .
Display Setting
Use Display settings to change the screen brightness, change the background image, enable screen rotation, set sleep time and change font size.
Setting the Screen Brightness
To manually set the screen brightness:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch Brightness Level.
Figure 1-31 Brightness Dialog Box
To let the TC70x/TC75x automatically adjust the screen brightness using the built-in light sensor:
1.
Touch Adaptive brightness to automatically adjust the brightness.
2.
Touch .
Setting Screen Rotation
By default, screen rotation is disabled. To enable screen rotation:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch When device is rotated and select Rotate to contents of the screen to set the TC70x/TC75x to automatically switch orientation when the TC70x/TC75x is rotated.
NOTE
The Home screen does not rotate.
4.
Touch .
Setting Screen Timeout Setting
To set the screen sleep time:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch Sleep.
1 - 20 TC70x/TC75x User Guide for Android Version 6.0.1
4.
Select one of the sleep values.
•
15 seconds
•
30 seconds
•
1 minute (default)
•
2 minutes
•
5 minutes
•
10 minutes
•
30 minutes
5.
Touch .
Setting Font Size
To set the size of the font is system applications:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
Touch Font size.
Select one of the font size values.
•
Small
•
Normal (default)
•
Large
•
Huge
5.
Touch .
Setting Touch Key Light
The four touch keys under the screen are backlit. Configure the touch key light to save battery power.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
Touch Touch key light.
Select one of the options.
•
Always off - The touch key light is off.
•
6 seconds - The touch key light stays on for six seconds and then turns off (default).
•
10 seconds - The touch key light stays on for 10 seconds and then turns off.
•
15 seconds - The touch key light stays on for 15 seconds and then turns off.
•
30 seconds - The touch key light stays on for 30 seconds and then turns off.
•
1 minute - The touch key light stays on for one minute and then turns off.
•
Always on - The touch key light is on when the screen is on.
Getting Started 1 - 21
Figure 1-32 Touch Key Light Dialog Box
5.
Touch .
Touch Mode
The TC70x/TC75x display is able to detect touches using a finger, a conductive-tip stylus or gloved finger.
NOTE
A glove can be made of medical latex, leather, cotton or wool.
For optimal performance use Zebra certified stylus.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch Touch screen mode.
Figure 1-33 Touch Panel Mode Dialog Box
4.
Select:
1 - 22 TC70x/TC75x User Guide for Android Version 6.0.1
a.
b.
c.
d.
Glove and Finger (Screen Protector on) to use a finger or a gloved finger on the screen with a screen protector.
Glove and Finger (Screen Protector off) to use a finger or a gloved finger on the screen without a screen protector.
Stylus and Finger (Screen Protector on) to use a finger or a stylus on the screen with a screen protector.
Stylus and Finger (Screen Protector off) to use a finger or a stylus on the screen without a screen protector.
5.
Touch .
Setting Notification LED
The Charging/Notification LED lights blue when an application, such as email and VoIP, generates a programmable notification or to indicate when the TC70x/TC75x is connected to a Bluetooth device. By default, LED notifications are enabled. To change the notification setting:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch Pulse notification light to toggle the notification on or off.
4.
Touch .
General Sound Setting
Use the Sounds settings to configure media and alarm volumes.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
Getting Started 1 - 23
Figure 1-34 Sound and Notification Screen
• Sound
•
Media volume - Controls the music, games and media volume.
•
Alarm volume - Controls the alarm clock volume.
•
Ring volume - Controls the ringtone volume.
•
Also vibrate for calls - Enable to make the device vibrate when a call is received (default – enabled).
•
Interruptions - Use to prioritize sound notifications. Touch the settings to turn call and message interruptions on or off.
If user turns Messages notifications on, touch Calls/messages from to specify from whom to accept notifications (Anyone, Starred contacts only or Contacts Only).
In Downtime section, select which days and times to allow for sound notifications.
•
Phone ringtone - Touch to select a ringtone to sound when an incoming call is received.
•
Default notification ringtone - Touch to select a sound to play for all system notifications.
• Other sounds
• Dial pad tones - Check to play a sound when a phone key is touched (default – enabled).
• Screen locking sounds - Check to play a sound when locking and unlocking the screen (default – enabled)
• Charging sounds - Check to play a sound when the device begins charging.
• Touch sounds - Check to play a sound when making screen selections (default – enabled).
• Vibrate on touch - Check to vibrate when making screen selections (default – enabled).
•
Cast screen - Transmit whatever is on the screen to a supported TV.
1 - 24 TC70x/TC75x User Guide for Android Version 6.0.1
• Notification
•
Pulse notification light - Blinks LED when a notification exists.
•
When device is locked - Manage whether notifications can be seen when the TC70x/TC75x is locked.
Options: Show all notification content (default) or Don’t show notifications at all.
•
App notification - Modify the notification settings individually for an application. The setting under When
device is locked always takes precedence over the setting for an individual application.
• Advanced
•
Notification access - Displays which applications can access notifications.
When a notification arrives, its icon appears at the top of the screen. Icons for pending notifications appear on the left, and system icons on the right.
•
Do Not Disturb access - Displays which applications can access DO Not Disturb feature.
Wake-Up Sources
By default the TC70x/TC75x wakes from suspend mode when the user presses the power button. The
TC70x/TC75x can be configured to wake when the user presses the PPT or Scan buttons on the left side of the device.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
Touch Keypad checkbox. A check appears in the checkbox.
Figure 1-35 Wake-Up Sources
4.
Touch .
CHAPTER 2 USING THE DEVICE
Introduction
This chapter explains the buttons, status icons, and controls on the TC70x/TC75x, and provides basic instructions for using the TC70x/TC75x including resetting the TC70x/TC75x and entering data.
Google Mobile Services
NOTE
This section only applies to TC70x/TC75x configurations with Google Mobile Services (GMS).
The TC70x/TC75x with GMS contains applications and services that provide additional functionality to the
TC70x/TC75x.
GMS includes:
•
Applications - GMS adds a variety of Google applications and associated widgets including Chrome, Gmail,
Drive and Maps.
• Services:
•
Speech to Text - Allows for free format speech to text, in many languages for both connected and disconnected network. Launch by touching the microphone icon on the keyboard.
•
TalkBack Service - Provides spoken feedback on various parts of the user interface. To enable, go to
Settings > Accessibility.
•
Network Location Provider - Adds a location provider which uses mobile network tower information and
Wi-Fi access point information to provide a location without using GPS. To enable, go to Settings >
Location access.
•
Widevine DRM - Enables the digital rights management so that protected content can be played. Enable via DRM Info from the Play Store.
•
Google Cloud Messaging - Allows the sending of data from your server to your TC70x/TC75x and also to receive messages from devices on the same connection.
•
Backup and Restore - Allows the users settings and applications to be backed up to a Google server and subsequently restored from that server after a factory reset.
2 - 2 TC70x/TC75x User Guide for Android Version 6.0.1
•
Google accounts - Create and use a Google account to synchronize mail, files, music, photos, contacts and calendar events.
Home Screen
The Home screen displays when the TC70x/TC75x turns on. Depending upon the configuration, the Home screen might appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock sliders. Touch the screen and slide up to unlock. For screen locking information see
Un-Locking the Screen on page 2-17
TC70x
Figure 2-1 Home Screen
Table 2-1 Home Screen Items
Item
1 — Status Bar
2 — Browser Icons
TC75x
Description
Displays the time, status icons (right side), and notification icons (left side). For more information see
.
Opens browser application.
Using the Device 2 - 3
Table 2-1 Home Screen Items (Continued)
Item
3 — All Apps Icon
4 — Shortcut Icons
5 — Widgets
Opens the APPS window.
Description
Opens applications installed on the TC70x/TC75x.
Launches stand-alone applications that run on the Home screen.
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
Some apps (e.g., Camera and Gallery) use the whole screen and hide the three soft button on the bottom of the screen.
Touch to show buttons
Figure 2-2 Hidden Soft Buttons
To show the button, touch the soft button area to display the button icons.
Status Bar
The Status bar displays the time, notification icons (left side) and status icons (right side).
NOTE
Some Status icons might not appear in the Status Bar if there are too many icons to display.
Notifications
Icons
Figure 2-3 Notification and Status Icons
Status Icons
If there are more notifications than can fit in the Status bar, displays indicating that more notifications exist.
Open the Notifications panel to view all notifications and status.
2 - 4 TC70x/TC75x User Guide for Android Version 6.0.1
Status Icons
Table 2-2 Status Icons
Icon
Indicates that the Alarm is active.
Description
Indicates that the main battery is fully charged.
Indicates that the main battery is partially drained.
Indicates that the main battery charge is low.
Indicates that the main battery charge is very low.
Indicates that the main battery is charging.
Indicates that all sounds except media and alarms are silenced and vibrate mode is active.
Indicates that the Airplane Mode is active. All radios are turned off.
Indicates that Bluetooth is on.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Mobile network signal strength (TC75x only).
No mobile network signal (TC75x only).
Connected to a 4G LTE/LTE-CA network (TC75x only) (see Note 1).
Connected to a DC-HSPA, HSDPA, HSPA+, HSUPA, LTE/LTE-CA or WCMDMA network (TC75x only) (see Note 1).
Connected to a 1x-RTT (Sprint), EGDGE, EVDO, EVDV or WCDMA network (TC75x only) (see
Note 1).
Connected to a DC - HSPA, HSDPA, HSPA+ or HSUPA network (TC75x only) (see Note 1).
Note 1: Cellular network icon that appears is dependent upon the carrier/network.
Using the Device 2 - 5
Table 2-2 Status Icons (Continued)
Icon Description
Connected to an EDGE network (TC75x only) (see Note 1).
Connected to a GPRS network (TC75x only) (see Note 1).
Connected to a GPRS network (see Note 1).
Connected to a 1x-RTT (Verizon) network (see Note 1).
Roaming from a network (TC75x only).
No SIM card installed (TC75x only).
Note 1: Cellular network icon that appears is dependent upon the carrier/network.
Notification Icons
Table 2-3 Notification Icons
Icon
Indicates the main battery is low.
Description
Indicates that more notifications are available for viewing.
Indicates that data is syncing.
Indicates an upcoming event.
Indicates that an open Wi-Fi network is available.
Indicates that a song is playing.
Indicates that a problem with sign-in or sync has occurred.
Indicates that the TC70x/TC75x is uploading data.
Indicates that the TC70x/TC75x is downloading data when animated and download is complete when static.
Indicates that the TC70x/TC75x is connected via USB cable.
Indicates that the TC70x/TC75x is connected to or disconnected from virtual private network (VPN).
Preparing Internal Storage.
2 - 6 TC70x/TC75x User Guide for Android Version 6.0.1
Table 2-3 Notification Icons (Continued)
Icon Description
Indicates that USB debugging is enabled on the TC70x/TC75x.
Indicates a call is in progress (TC75x only).
Indicates that one or more voice message is in mailbox (TC75x only).
Indicates that the call is on hold (TC75x only).
Indicates that a call was missed (TC75x only).
Indicates that a headset is connected to the device.
Indicates the status of the PTT Express Voice Client. See Notification Icons for complete list of PTT
Express notification icons.
Indicates the RS6000 is connected to the device.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events.
When a notification occurs, an icon appears in the Status bar with a brief description. See
Notification Icons on page 2-5
the notifications.
To open the Notification panel drag the Status bar down from the top of the screen.
Figure 2-4 Notification Panel
To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel closes and the subsequent activity is dependent on the notification.
To clear all notifications, open the Notifications Panel and then touch . All event-based notifications are removed. Ongoing notifications remain in the list.
Ongoing notifications remain in the list.
To close the Notification Panel, swipe the Notifications Panel up.
Using the Device 2 - 7
Quick Settings
Use Quick Access Panel to get to frequently used settings, like turning on airplane mode. To open Quick Access
Panel, swipe down from the top of the screen with two fingers or twice with one finger.
Figure 2-5 Quick Settings
To change a setting, just touch the icon:
•
Display brightness: Slide to lower or increase the brightness of the screen.
•
Wi-Fi network: Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
•
Bluetooth settings: Turn Bluetooth on or off. To open Bluetooth settings, touch the Bluetooth.
•
Do not disturb: Control how and when to receive notifications.
•
Cellular: Turns cellular radio on or off. To open Cellular settings, touch (TC75x only)
•
Airplane mode: Turn airplane mode on or off. Airplane mode means device will not connect to Wi-Fi or
Bluetooth.
•
Auto-rotate: Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
•
Flashlight: Turn camera flash on or off.
•
Location: Enable or disable locationing feature.
Using the Touchscreen
Use the multi-tap sensitive screen to operate the device.
•
Tap - Tap to:
•
select items on the screen
•
type letters and symbols using the on-screen keyboard
•
press on-screen buttons.
2 - 8 TC70x/TC75x User Guide for Android Version 6.0.1
•
Tap and Hold - Tap and hold:
•
an item on the Home screen to move it to a new location or to the trash.
•
an item in Apps to create a shortcut on the Home screen.
•
the Home screen to open a menu for customizing the Home screen.
•
an empty area on the Home screen until the menu appears.
•
Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new position.
•
Swipe- Move finger up and down or left and right on the screen to:
•
unlock the screen
•
view additional Home screens
•
view additional application icons in the Launcher window
•
view more information on an application’s screen.
•
Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
•
Pinch - In some applications, zoom in and out by placing two fingers on the screen and pinching them together (to zoom out) or spreading them apart (to zoom in).
Keyboards
The device has two types of keyboards:
•
Enterprise Keyboard
•
Android Keyboard (default).
To switch between keyboards:
1.
Touch in a text box to display the current keyboard.
2.
On the Enterprise keyboard, touch and hold or on the Android keyboard, touch and hold .
Figure 2-6 Change Keyboard Dialog Box
3.
Select the desired keyboard.
Keyboard Configuration
To configure the keyboard, See the Keyboard Settings section in the TC70x/TC75X Integrator Guide for Android
Version 6.0.1.
Using the Device 2 - 9
Using the Enterprise Keyboard
The Enterprise Keyboard contains the following keyboards:
•
Numeric
•
Alpha
•
Special characters
•
Data capture.
Numeric Tab
To access the numeric keyboard, touch the 123 tab.
Figure 2-7 Numeric Keyboard
Alpha Tab
To access the alpha keyboard, touch the EN tab.
NOTE
The Enterprise keyboard support English (US), English (UK), French, German, Spanish and Italian. When a keyboard language is selected in Settings, the corresponding keyboard language displays.
Figure 2-8 Alpha Keyboard
Touch to enter emoji icons in a text message.
2 - 10 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 2-9 Emoji Keyboard
Touch ABC to return to the Alpha keyboard.
Additional Character Tab
To access additional characters, touch the #*/ tab.
Figure 2-10 Symbols Keyboard
Scan Tab
The Scan tab provides an easy data capture feature for scanning bar codes.
Figure 2-11 Scan Keyboard
Using the Android Keyboard
Use the on-screen keyboard to enter text in a text field. To configure the keyboard settings, touch and hold
(comma) > and then select Android keyboard settings.
Using the Device 2 - 11
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some applications do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols and Special Characters
To enter numbers and symbols:
•
Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate characters display an ellipsis ( ... ) below the character.
•
Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them, and then lift both fingers to return to the lowercase keyboard.
•
Touch to switch to the numbers and symbols keyboard.
•
Touch the key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
•
A larger version of the key displays briefly over the keyboard.
•
Keys with alternate characters display an ellipsis ( ... ) below the character.
2 - 12 TC70x/TC75x User Guide for Android Version 6.0.1
Applications
The APPS screen displays icons for all installed applications. The table below lists the applications installed on the
TC70x/TC75x. Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing and uninstalling application.
Table 2-4 Applications
Icon Description
App Gallery - Provides links to utilities and demonstration applications that can be installed on the device.
Battery Management - Displays battery information, including charge level, status, health and wear level.
Battery Swap – Use to place device in Battery Swap mode when replacing the battery.
Bluetooth Pairing Utility – Use to pair the RS507 Hans-free Imager with the TC70x/TC75x by scanning a bar code.
Browser - Use to access the Internet or intranet.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments.
Chrome - Use to access the Internet or intranet.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information. See
for more information.
DataWedge - Enables data capture using the imager.
Using the Device 2 - 13
Table 2-4 Applications (Continued)
Icon
Downloads - lists all downloads files.
Description
Duo - A one-to-one video calling application (Available only on devices with GMS software).
Drive - Upload photos, videos, documents, and other files to personal storage site.
DWDemo - Provides a way to demonstrate the data capture features using the imager. See
DataWedge Demonstration on page 4-21
elemez — Use to provide diagnostic information. See
for more information.
Email - Use to send and receive email.
File Browser - Organize and manage files on the TC70x/TC75x. See
for more information.
Gallery - Use to view photos stored on the microSD card. For more information, see
Gmail - Use to send and receive email using a Google email account.
Google - Launches Google search application.
Google+ - Connect with people on Google social network.
Hangouts - Use to communicate with friends using text messages and photos.
2 - 14 TC70x/TC75x User Guide for Android Version 6.0.1
Table 2-4 Applications (Continued)
Icon Description
Maps - Use to see you location on a map (with public transit, traffic or satellite overlays). Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance and traffic-avoidance and alternate routes, for drivers, cyclist, walkers and users of public transportation.
Messaging - Send SMS and MMS messages. See
for more information
(TC75x only).
MobiControl Stage – Opens the MobiControl Stage application to stage the device.
News & Weather - Provides news and weather information.
Notes - Use to take and save notes.
Phone - Use to dial a phone number when used with some Voice over IP (VoIP) clients (VoIP telephony ready only) (TC75x only).
Photos - Use to sync photos with Google account.
Play Books - Use to read books.
Play Games - Use to play games.
Play Movies & TV - View movies and video on your device.
Play Music - Use to listen to music.
Play Newsstand - Displays current news.
Using the Device 2 - 15
Table 2-4 Applications (Continued)
Icon Description
Play Store - Download music, movies, books, and Android apps and games from the Google
Play Store.
PTT Express - Use to launch PTT Express client for VoIP communication.
Rapid Deployment - Allows the TC70x/TC75x to stage a device for initial use by initiating the deployment of settings, firmware and software. Requires the purchase of an MSP client license per device.
RxLogger - Use to diagnose device and application issues. See the TC70x/TC75x Integrator
Guide for Android Version 6.0.1 for more information.
Settings - Use to configure the TC70x/TC75x.
Snapdragon Camera - Take photos or record videos.For more information see
Sound Recorder - Use to record audio.
StageNow - Allows the TC70x/TC75x to stage a device for initial use by initiating the deployment of settings, firmware and software.
Tethering & portable hotspot - Use to configure tethering and Wi-Fi hotspot.
Voice Search - Use to perform searches by asking questions.
YouTube - Use to view videos on the YouTube web site.
Accessing Applications
All applications installed on the device are accessed using the APPS window.
1.
On the Home screen, touch .
2 - 16 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 2-12 APPS Window Example
2.
Slide the APPS window left or right to view more application icons. Touch an icon to open the application.
Switching Between Recent Applications
1.
Touch . A window appears on the screen with icons of recently used applications.
Using the Device 2 - 17
1
Figure 2-13 Recently Used Applications
2.
3.
Slide the window up and down to view all recently used applications.
Swipe left or right to remove application from the list and force close the application.
4.
Touch an icon to open it or touch to return to the current screen.
Un-Locking the Screen
Use the Lock screen to protect access to data on the TC70x/TC75x. Some email account require locking the screen. Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on setting up the locking feature. The Locking feature functions differently in Single User mode or Multiple User mode.
When locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device.
The Lock screen displays. Slide to the right toward to unlock the screen.
If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
2 - 18 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 2-14 Lock Screen
Figure 2-15 PIN Screen
Using the Device 2 - 19
2 - 20 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 2-16 Pattern Screen
Using the Device 2 - 21
Figure 2-17 Password Screen
Interactive Sensor Technology
The TC70x/TC75x contains sensors that monitor movement, orientation and ambient light:
•
Gyroscope - Measures angular rotational velocity to detect rotation of the device.
•
Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
•
Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate your digital maps depending on your physical orientation.
•
Light Sensor - Used to detect ambient light and adjust the screen brightness.
•
Proximity Sensor - Uses to detect presence of nearby objects without physical contact.
In order to take advantage of these sensors, applications use API commands. Refer to the Zebra Android EMDK for more information.
Resetting the Device
There are two reset functions, soft reset and hard reset.
2 - 22 TC70x/TC75x User Guide for Android Version 6.0.1
Performing a Soft Reset
1.
2.
3.
Perform a soft reset if applications stop responding.
Press and hold the Power button until the menu appears.
Touch Reset.
The device reboots.
Performing a Hard Reset
CAUTION
Performing a hard reset with a SD card installed in the TC70x/TC75x may cause damage or data corruption to the SD card.
1.
2.
3.
Perform a hard reset if the TC70x/TC75x stops responding.
Simultaneously press the Power, Scan and Volume Up buttons for at least four seconds.
When the screen turns off, release the buttons.
The TC70x/TC75x reboots.
Suspend Mode
The TC70x/TC75x goes into suspend mode when the user presses the Power button or after a period of inactivity
(set in the Display settings window).
To wake the TC70x/TC75x from Suspend mode, press the Power button.
The Lock screen displays. Slide to the right toward to unlock the screen. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. See
Un-Locking the Screen on page 2-17
NOTE
If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds before trying again.
If the user forgets the PIN, password or pattern contact the system administrator.
Figure 2-18 Lock Screen
Using the Device 2 - 23
2 - 24 TC70x/TC75x User Guide for Android Version 6.0.1
CHAPTER 3 CALLS
NOTE
TC75x only.
Make a phone call from the Phone application, the Contacts application or other applications or widgets that display contact information.
Emergency Calling
The service provider programs one or more emergency phone numbers, such as 911 or 999, that the user can call under any circumstances, even when the phone is locked, a SIM card is not inserted or the phone is not activated.
The service provider can program additional emergency numbers into the SIM card. However, the SIM card must be inserted in the device in order to use the numbers stored on it. See the service provider for additional information.
NOTE
Emergency numbers vary by country. The phone’s pre-programmed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.
Audio Modes
The device offers three audio modes for use during phone calls:
•
Handset Mode: Switches audio to the receiver at the top front of the device, so the user can use the device as a handset. This is the default mode.
•
Speaker Mode: Use the device as if on speaker phone.
•
Headset Mode: Connect a Bluetooth or wired headset to automatically switch audio to the headset.
3 - 2 TC70x/TC75x User Guide for Android Version 6.0.1
Using a Bluetooth Headset
Use a Bluetooth headset for audio communication when using an audio-enabled application. See
for information on connecting a Bluetooth headset to the device. Set the volume appropriately before
putting on the headset. When a Bluetooth headset is connected, the speakerphone is muted.
Using a Wired Headset
Use a wired headset and Audio Adapter for audio communication when using an audio-enabled application. Set the volume appropriately before putting on the headset. When a wired headset is connected, the speakerphone is muted.
To end a call using the wired headset, press and hold the headset button until the call ends.
Figure 3-1 3.5 mm Headset Adapter
Adjusting Audio Volume
Use the Volume buttons to adjust the volume of the ringer when not in a call and the audio volume when in a call.
NOTE
Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring and notification sound levels.
Making a Call Using the Dialer
Use the dialer tab to dial phone numbers.
1.
On the Home screen touch .
2.
Touch .
Calls 3 - 3
Figure 3-2 Dialer Screen
3.
Touch the keys to enter the phone number.
4.
Touch below the dialer to initiate the call.
3 - 4 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 3-3 Call in Progress
•
•
•
- touch to send audio to the speakerphone.
- touch to mute the call.
- touch to display the dial pad.
•
•
- touch to place the call on hold.
- touch to create a conference call.
5.
Touch to end the call.
If using a Bluetooth headset, additional audio options are available. Touch the audio icon to open the audio menu.
Calls 3 - 5
Figure 3-4 Bluetooth Audio Options
•
•
•
- indicates that audio is routed to the Bluetooth headset.
- indicates that audio is routed to the speakerphone.
- indicates that audio is routed to the earpiece.
Dialer Dialing Options
The dialer provides options to save the dialed number to contacts, insert pauses and wait into the dial string and options for setting the Call settings. Enter at least one digit to access these options. Touch to access the following.
•
Add 2–sec pause - pause the dialing of the next number for two seconds. Multiple pauses can be added sequentially.
•
Add wait - wait for confirmation to send the rest of the digits.
3 - 6 TC70x/TC75x User Guide for Android Version 6.0.1
Making a Call Using Contacts
There are two ways to make a call using contacts:
•
Using the Dialer
•
Using the Contacts application.
Using the Dialer
1.
On the Home screen touch .
2.
Touch the tab.
Figure 3-5 Dialer Contacts Tab
3.
Touch the contact.
4.
Touch to initiate the call.
5.
Touch to end the call.
Using the Contacts Application
To make a call from the Contacts application:
1.
Touch .
Figure 3-6 Contact Application
2.
Touch a contact name.
Calls 3 - 7
3 - 8 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 3-7 Contact Information
3.
Touch to initiate a call.
Making a Call Using Call History
Call History is a list of all the calls placed, received, or missed. It provides a convenient way to redial a number, return a call, or add a number to Contacts.
Arrow icons beside a call indicate the type of call. Multiple arrows indicate multiple calls:
•
•
•
- Missed incoming call
- Received incoming call
- Outgoing call.
1.
On the Home screen touch .
2.
Touch the tab.
Calls 3 - 9
Figure 3-8 Call History Tab
3.
4.
Touch next to the contact to initiate the call.
Touch the contact to perform other functions.
5.
Touch to end the call.
Making a Conference Call
To create a conference phone session with multiple people.
NOTE
Conference Calling and the number of conference calls allowed may not be available on all services.
Please check with the service provider for Conference Calling availability.
1.
On the Home screen touch .
2.
3.
Touch .
Touch the keys to enter the phone number.
4.
Touch below the dialer to initiate the call.
5.
6.
When the call connects, touch .
The first call is placed on hold.
Touch the keys to enter the second phone number.
3 - 10 TC70x/TC75x User Guide for Android Version 6.0.1
7.
8.
Touch below the dialer to initiate the call.
When the call connects, the first call is placed on hold and the second call is active.
Figure 3-9 Two Calls
9.
Touch icon to create a conference call with three people.
Figure 3-10 Merged Calls
10.
Touch to add another call.
The conference is placed on hold.
11.
Touch the keys to enter the second phone number.
12.
Touch below the dialer to initiate the call.
13.
Touch icon to add the third call to the conference.
14.
Touch Manage Conference call to view all callers.
Calls 3 - 11
3 - 12 TC70x/TC75x User Guide for Android Version 6.0.1
Figure 3-11 Un-merge Calls
15.
To remove a caller from the conference, touch next to the caller.
To speak privately with one party during a conference call, touch . To include all parties again, touch .
Calls 3 - 13
Answering Calls
When you receive a phone call, the Incoming Call screen displays, displaying the caller ID and any additional information about the caller that is in the Contacts application.
Figure 3-12 Incoming Call Screen
Touch Answer to answer the call or Dismiss to send the caller to voice mail.
If the screen lock is enabled, the user can still answer the call without unlocking the device.
Figure 3-13 Incoming Call Locked Screen
When a call arrives, touch the white phone icon and slide over one of these icons:
•
•
•
Answer call - Start talking to the caller.
Send to voice mail - Direct the caller to leave a voice mail message.
Send a message - Opens a list of quick text responses. Touch one to send it to the caller immediately.
3 - 14 TC70x/TC75x User Guide for Android Version 6.0.1
When the calls ends, the device remains locked.
If using a Bluetooth headset, when a call arrives, touch the Call button on the Bluetooth headset to answer the call.
To end the call press the headset Call button.
All incoming calls are recorded in the Phone application Call log tab. If you miss a call, you receive a notification. To silence the ringer before answering the call, press the volume down button on the side of device.
Call Settings
NOTE
Not all options are available for all configurations.
Use the Call Settings to modify options related to the phone call feature.
• Display options
•
Sort by - Options: First name or Last name.
•
Name format - Options: First name first or Last name first.
• Sounds and vibrations
•
Phone ringtone - Touch to select a ringtone to sound when an incoming call is received.
•
Also vibrate for calls - Check to make the device vibrate when a call is received (default - disabled).
•
Dialpad tones - Check to play a sound when a phone key is touched (default - enabled).
•
Quick responses - Touch to edit quick responses to use instead of answering a call.
•
Speed dial settings - Set speed dial contact shortcuts.
• Calls
• Calling accounts
• SIP accounts - Choose to receive Internet calls for accounts added to the device, view or change SIP accounts, or add an Internet calling account.
• Use SIP calling - Options: For all calls or Only for SIP calls (default).
• Receive incoming calls - When enabled, allows incoming calls (default - disabled).
• Display duration - When enabled, displays the duration of the call (default - enabled).
• Vibrating after connected - When enabled, the device vibrates after connecting to the SIP call
(default - enabled).
• Turn on proximity sensor - When enabled, the screen turn off to save power. (default - enabled)
•
Voicemail - Touch to configure voicemail settings.
• Service - Set the service provider or other provider for voicemail service.
• Setup - Touch to update the phone number used to access voicemail.
• Sound - Touch to select a sound to play when a voicemail is received.
• Vibrate - Set vibrate option. (default – disabled).
•
Fixed Dialing Numbers - Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed Dialing list.
• GSM call settings
• Call forwarding - Use call forwarding to forward incoming calls to a different phone number.
Calls 3 - 15
NOTE
Call Forwarding may not be available on all networks. Check with the service provider for availability.
• Additional settings
• Caller ID - Enable caller ID to reveal the identity of the person making an outgoing call. Options:
Network default (default), Hide number, Show number.
• Call waiting - set to be notified of an incoming call while on a call.
• Call barring - Use call barring to block certain types of incoming and/or outgoing calls. Select the type of incoming and/or outgoing calls to block.
• Accessibility
•
TTY mode - Touch to set the TTY setting. Use an optional teletypewriter (TTY) device with the TC75x to send and receive calls. Plug the TTY device into the TC75x headset jack and set the TC75x to operate in one of the TTY modes.
NOTE
Use a TSB-121 compliant cable (provided by the TTY manufacturer) to connect the TTY device to the
TC75x.
Set the TC75x volume to a middle level setting for proper operation. If you experience a high number of incorrect characters, adjust the volume as needed to minimize the error rate.
For optimal performance, the TC75x should be at least 30 cm (12 inches) from the TTY device. Placing the TC75x too close to the TTY device may cause high error rates.
• TTY off (default) - TTY is off.
• TTY Full - Transmit and receive TTY characters.
• TTY HCO - Transmit TTY characters but receive by listening to earpiece.
• TTY VCO - Receive TTY characters but transmit by speaking into microphone.
3 - 16 TC70x/TC75x User Guide for Android Version 6.0.1
CHAPTER 4 APPLICATIONS
This section describes the applications installed on the device.
Battery Manager
The Battery Manager provides detailed information about the battery.
Figure 4-1 Battery Manager Screen
4 - 2 TC75x User Guide for Android Version 6.0.1
Table 4-1 Battery Icon Description
Battery Icon
Indicates battery charge level.
Description
Indicates battery charging.
Indicates battery charge level is below 20%.
•
Battery level - Indicate the current battery charge level as a percentage. Displays -% when level is unknown.
• Battery status
• Not charging - Indicates that the device is not connected to AC power.
• Charging over AC - Indicates that the device is connected to AC power and charging.
• Charging over USB - Indicates that the device is connected to a host computer with a USB cable and charging.
• Discharging - Indicates that the battery is discharging.
• Full - Indicates that the battery is fully charged.
• Unknown - Indicates that the battery status is unknown.
•
Battery health - Indicates the health of the battery. If a critical error occurs, appears. Touch to view error description.
• Decommission - The battery is past it’s useful life and should be replaced. See system administrator.
• Good - The battery is good.
• Charge error - An error occurred while charging. See system administrator.
• Over Current - An over-current condition occurred. See system administrator.
• Dead - The battery has no charge. Replace the battery.
• Over Voltage - An over-voltage condition occurred. See system administrator.
• Below Temperature - The battery temperature is below the
• Failure Detected - A failure has been detected in the battery. See system administrator.
• Unknown - See system administrator.
•
Wear level - Indicates the health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
Applications 4 - 3
•
Advanced info - Touch to view additional battery information.
• Battery present status
•
Battery level - Indicates battery charge level as a percentage of scale.
• Battery scale - Battery scale level used to determine battery level (100).
• Battery voltage - Indicates current battery voltage in millivolts.
• Battery temperature - Indicates current battery temperature in degrees Centigrade.
• Battery technology - Lists the type of battery.
• Battery manufacture date - Lists the date of manufacture.
• Battery serial number - Lists the battery serial number. The number matches the serial number printed on the battery label.
• Battery part number - Lists the battery part number.
• Backup battery level - Indicates the current backup battery charge level as a percentage.
• Battery rated capacity - Lists the rated capacity of the backup battery in mAh.
• Battery decommission status - Indicates if the battery is past it’s life span.
• Battery Good - Battery is in good health.
• Decommissioned Battery - Battery is past it’s useful life and should be replaced.
• Base cumulative charge - Indicates the total amount of charge applied to the battery.
• Battery usage number - Indicates the number of charge cycles of the battery.
• Usage decommission threshold - Lists the threshold charge cycle count. When the Battery usage number reaches this value the battery should be decommissioned.
• App version - Lists the application version number.
4 - 4 TC75x User Guide for Android Version 6.0.1
File Browser
Use the File Browser application to view and mange files on the device.
To open File Browser, touch > .
Figure 4-2 File Browser Screen
The address bar indicates the current folder path. Touch the current folder path to manually enter a path and folder name.
Use
Use
to select multiple files/folder.
to view the internal storage root folder.
Use
Use
to view the microSD card root folder.
to view the previous folder or to exit the application.
Touch and hold an item to perform an operation on that item. Select one of the options from the File Operations menu:
•
Information - View detailed information about the file or folder.
•
Move - Move the file or folder to a new location.
•
Copy - Copy the select file.
•
Delete - Delete the selected file.
•
Rename - Rename the select file.
•
Open as - Open the selected file as a specific file type.
•
Share - Share the file with other devices.
Applications 4 - 5
4 - 6 TC75x User Guide for Android Version 6.0.1
Messaging
NOTE
TC75x only.
Use Messaging to send and receive SMS and MMS messages. From a Home or All Apps screen, touch .
Sending a Text Message
1.
In the main Messaging screen, touch .
Figure 4-3 New Text Message Screen
2.
3.
In the To field, enter a name or a mobile phone number.
In the Type message field, enter the text message.
The 160-character limit counter indicates how many characters are left. If it goes over that limit, a new message is created, which is joined with its predecessors when received.
If the user presses the Back button while composing a message, it’s saved as a draft in the Messaging screen.
Touch the conversation to resume composing it.
4.
Touch to send the message.
Sending a Multimedia Message
1.
2.
In the main Messaging screen, touch .
In the To field, enter a name or a mobile phone number.
3.
Touch to attach the media file of your choice:
Applications 4 - 7
Figure 4-4 New Multimedia Message Screen
•
Pictures. Select a picture to attach.
•
Capture picture. Camera opens to take a picture and attach it.
•
Videos. Select a video to attach.
•
Capture video. Camcorder opens to record a video and attach it to the message.
•
Audio. Choose a sound file to attach.
•
Record audio. Sound Recorder opens to record a spoken message and attach it to the message.
•
Slideshow. Opens a screen opens to assemble text, photos, videos, and recordings into a slideshow of up to 10 slides to attach to the message.
•
Insert contact info.
•
Contact vCard. Send a contact’s information.
4.
Touch to send the message.
4 - 8 TC75x User Guide for Android Version 6.0.1
Contacts
Use the Contacts application to manage contacts.
From a Home or Apps screen, touch . People opens to the main list of contacts. View contacts in three ways at the top of the screen: Groups, All contacts, and Favorites. Touch the tabs to change how to view the contacts.
Swipe up or down to scroll through the lists.
Adding a Contact
1.
2.
3.
4.
5.
In the Contacts application, touch .
If there are more than one account with contacts, touch the one to use.
Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all categories.
To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of the item of contact information. Or, to create your own label, touch Custom in the menu.
Touch <- Add New Contact.
Editing Contacts
1.
In the Contacts application, touch a contact name to edit.
2.
3.
4.
Touch .
Edit the contact information.
Touch <- Edit contact.
Deleting Contacts
1.
In the Contacts application, touch a contact name to delete.
2.
3.
4.
Touch .
Touch Delete.
Touch OK to confirm.
Applications 4 - 9
Camera
This section provides information for taking photos and recording videos using the integrated digital cameras.
NOTE
If a microSD card is installed, The TC70x/TC75x saves photos and videos on the microSD card. If a microSD card is not installed, the TC70x/TC75x saves photos and videos on the internal storage.
Front camera is optional.
Taking Photos
NOTE
Camera settings are described in
1.
Touch .
2.
Touch .
Filters
Scene Mode
Camera Switch
Beautification
Settings
Gallery
Camera Mode
Figure 4-5 Camera Mode
Shutter Button
3.
If necessary, touch the Camera Mode icon and touch .
4 - 10 TC75x User Guide for Android Version 6.0.1
4.
5.
6.
7.
To switch between the rear camera and front camera, touch .
Frame the subject on the screen.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
Touch an area on the screen to focus. The focus circle appears on the screen. The two bars turn green when in focus.
8.
Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Taking a Panoramic Photo
Panorama mode lets the user create a single wide image by panning slowly across a scene.
1.
Touch .
2.
Touch .
Figure 4-6 Panoramic Mode
3.
4.
Touch the Camera Mode and touch .
Frame one side of the scene to capture.
Applications 4 - 11
5.
Touch and slowly start panning across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If panning too quickly, the message Too fast appears.
6.
Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
Recording Videos
To record a video:
1.
Touch .
2.
Touch .
3.
Touch the options bar and touch .
Filters
Camera Switch
Audio
Settings
Gallery
Camera Mode
Shutter Button
Figure 4-7 Video Mode
4.
5.
To switch between the rear camera and front camera, touch .
Point the camera and frame the scene.
4 - 12 TC75x User Guide for Android Version 6.0.1
6.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
7.
Touch to start recording.
The device starts recording the video. The video time remaining appears in the top left of the screen.
8.
Touch to end recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
When in Photo mode, photo settings are displayed on screen. Touch to display the photo settings options.
Rear Camera
•
Flash - Touch to set whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
•
•
Off - Disable flash.
Auto - Camera adjusts flash automatically depending upon light meter (default).
On - Enable flash upon taking a photo.
•
Torch - Turn flash on continuously.
•
GPS location - Touch to add GPS coordinates to photo. Options: On (default) or Off.
•
Picture size - Touch to set the size (in pixels) of the photo. Options: 13M pixels (default), 12M pixels, 8M
pixels, Square (1:1), 5M pixels, 4M pixels (16:9), 3M pixels, HD 1080, 2M pixels, 1.5M pixels, 1.3M
pixels, WXGA, HD 720, 1M pixels, SVGA, WVGA, 720 x 480, VGA, CIF or QVGA or QCIF.
•
Picture quality - Touch to select picture quality setting. Options: Low, Standard (default) or High.
•
Countdown timer - Options: Off (default), 2 seconds, 5 seconds or 10 seconds.
•
Storage – Touch to select location to store the photo. Options: Phone or SD Card.
•
Continuous Shot - Select to enable or disable Options: On or Off (default).
•
Face Detection - Select to enable face detection. Options: Off (default) or On.
•
ISO - Set how sensitive the camera is to light. Options: Auto (default), ISO Auto (HJR), ISO100, ISO200,
ISO400, ISO800 or ISO1600.
•
Exposure - Touch to adjust the exposure settings. Options: +2, +1, 0(default), -1 or -2.
•
White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
• Incandescent - Adjust the white balance for incandescent lighting.
•
•
•
Fluorescent - Adjust the white balance for florescent lighting.
Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
•
Focus mode - Touch to select the camera focus setting. Options: Auto, Infinity, Macro or CAF (Continuous
Auto Focus) (default).
•
ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled)
Applications 4 - 13
Front Camera
Touch to display the photo setting options.
•
GPS location -
•
Picture size - Touch to set the size (in pixels) of the photo. Options: 1.3M pixels (default), WXGA, HD720,
1M pixels, SVGA, WVGA, 720 x 480, VGA, CIF or QVGA or QCIF.
•
Picture quality - Touch to select picture quality setting. Options: Low, Standard (default) or High.
•
Countdown timer - Options: Off (default), 2 seconds, 5 seconds or 10 seconds.
•
Storage – Touch to select location to store the photo. Options: Phone or SD Card.
•
Face Detection - Select to enable face detection. Options: Off (default) or On.
Video Settings
When in Video mode, video settings are displayed on screen. Touch to display the video settings options.
Rear Camera
Touch to display the photo setting options.
•
Flash - Touch to set whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
Off - Disable flash (default).
•
Torch - Turn flash on continuously.
•
Video quality - Touch to select video quality. Options: 4k UHD, HD 1080p (default), HD 720p, SD 480p,
VGA, CIF, QVGA or QCIF.
•
Video duration - Options: 30 seconds (MMS) 10 minutes (default), 30 minutes or no limit.
•
GPS location -
•
Storage – Touch to select location to store the photo. Options: Phone (default) or SD Card.
•
White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
•
•
Incandescent - Adjust the white balance for incandescent lighting.
Fluorescent - Adjust the white balance for florescent lighting.
•
•
•
Auto - Adjust the white balance automatically (default).
Daylight - Adjust the white balance for daylight.
Cloudy - Adjust the white balance for a cloudy environment.
Front Camera
•
Video quality - Touch to select video quality. Options: HD 720p (default), SD 480p, VGA, CIF, QVGA or
QCIF.
•
Video duration - Options: 30 seconds (MMS) 10 minutes (default), 30 minutes or no limit.
•
GPS location - Options: On (default) or Off.
•
Storage – Touch to select location to store the photo. Options: Phone (default) or SD Card.
4 - 14 TC75x User Guide for Android Version 6.0.1
Gallery
NOTE
The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Use Gallery to:
•
view photos
•
play videos
•
perform basic editing of photos
•
set photos as wallpaper
•
set photos as a contact photo
•
share photos and videos.
Gallery presents all photos and videos stored on the microSD card and internal memory.
To open the Gallery application, touch > or in the camera application touch the thumbnail image at the bottom left.
By default, Gallery open to the Timeline view.
Figure 4-8 Gallery - Timeline View
Touch > Videos to view only videos.
Applications 4 - 15
Figure 4-9 Gallery — Albums View
•
Touch an album to open it and view its contents. The photos and videos in the album are displayed in chronological order.
•
Touch a photo or video in an album to view it.
•
Touch to return to the main Gallery screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
4 - 16 TC75x User Guide for Android Version 6.0.1
Figure 4-10 Photos Inside an Album
Swipe left or right to scroll images across the screen.
Share an Album
1.
2.
3.
Touch and hold an album until it highlights.
Touch other albums as required.
4.
5.
Touch . The Share menu opens. Touch the application to use to share the selected albums.
Follow the instructions within the selected application.
Get Album Information
1.
2.
Touch and hold an album until it highlights.
3.
4.
Touch .
Touch Details.
Deleting an Album
To delete an album and its contents:
1.
2.
3.
Touch and hold an album until it highlights.
Check other albums to delete. Ensure that other albums are selected.
4.
5.
Touch .
In the Delete selected item? menu, touch OK to delete the album.
Working with Photos
Use Gallery to view photos on the microSD card and edit and share photos.
Viewing and Browsing Photos
To view a photo:
1.
2.
3.
Touch an album to open it.
Touch a photo.
Applications 4 - 17
Figure 4-11 Photo Example
6.
7.
8.
4.
5.
Swipe left or right to view the next or previous photo in the album.
Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is displayed (but not saved) in the new orientation.
Touch the photo to view the controls.
Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.
Drag the photo to view parts that are not in view.
4 - 18 TC75x User Guide for Android Version 6.0.1
Cropping a Photo
1.
In Gallery, touch a photo to view the controls.
2.
3.
Touch Crop. The cropping tool appears.
Use the cropping tool to select the portion of the photo to crop.
•
Drag from the inside of the cropping tool to move it.
•
Drag an edge of the cropping tool to resize it to any proportion.
Figure 4-12 Cropping Tool
4.
Touch Done to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
1.
2.
3.
Touch an album to open it.
Touch the photo to open it.
4.
5.
6.
7.
8.
9.
Touch .
Touch Set picture as.
Touch Contact photo.
In the People application, touch a contact.
Touch the white box and crop the photo accordingly.
Touch Done.
Applications 4 - 19
Share a Photo
1.
2.
3.
Touch an album to open it.
Touch a photo to open it.
4.
5.
Touch .
Touch the application to use to share the selected photo. The application selected opens with the photo attached to a new message.
Deleting a Photo
1.
2.
3.
Touch an album to open it.
Touch a photo to open it.
4.
5.
6.
Touch .
Touch Delete.
Touch OK to delete the photo.
Working with Videos
Use Gallery to view videos and share videos.
Watching Videos
1.
2.
3.
Touch an album to open it.
Touch a video.
4.
5.
Touch . The video begins to play.
Touch the screen to view the playback controls.
Sharing a Video
1.
2.
3.
Touch an album to open it.
Touch a video to open it.
4.
5.
Touch . The Share menu appears.
Touch the application to use to share the selected video. The application selected opens with the video attached to a new message.
Deleting a Video
1.
2.
3.
Touch an album to open it.
Touch a video to open it.
4.
Touch .
4 - 20 TC75x User Guide for Android Version 6.0.1
5.
6.
Touch Delete.
Touch OK.
Applications 4 - 21
DataWedge Demonstration
NOTE
DataWedge is enabled when on the Home screen displays. To disable this feature, go to the DataWedge settings and disable the Launcher profile.
Use DataWedge Demonstration to demonstrate data capture functionality.
Figure 4-13 DataWedge Demonstration Window
Table 4-2 DataWedge Demonstration Icons
/
Icon Description
Toggles illumination on and off when using the internal imager or optional RS507 or RS6000 scanners to capture bar code data.
/ /
Toggles the data capture function between the internal imager,RS507 or RS6000 scanner (if connected).
/
Toggles between normal scan mode and picklist mode when using the imager to capture bar code data.
Opens a menu to view the application information or to set the application DataWedge profile.
4 - 22 TC75x User Guide for Android Version 6.0.1
NOTE
See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on DataWedge configuration.
Either press the programmable button or touch the yellow scan button to enable data capture. The captured data appears in the text field below the yellow button.
Applications 4 - 23
Sound Recorder
Use Sound Recorder to record audio messages.
Recordings are saved on the microSD card (if installed) or the Internal Storage and available in the Music application playlist titled “My Recordings.”
Figure 4-14 Sound Recorder Application
4 - 24 TC75x User Guide for Android Version 6.0.1
PTT Express Voice Client
NOTE
PTT Express Voice Client creates Push-To-Talk (PTT) communication capability between disparate enterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without the need of a voice communication server.
•
Group Call: Press and hold the PTT (Talk) button to start communicating with other voice client users.
•
Private Response: Double-press the PTT button to respond to the originator of the last broadcast or to make a Private Response.
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
•
Talk Tone: Double chirp. Plays when the Talk button is depressed. This is a prompt for the user to start talking.
•
Access Tone: Single beep. Plays when another user just finished a broadcast or response. The user is now able to initiate a Group Broadcast or Private Response.
•
Busy Tone: Continuous tone. Plays when the Talk button is depressed and another user is already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
•
Network Tone:
•
Three increasing pitch beeps. Plays when PTT Express has acquired the WLAN connection and the service is enabled.
•
Three decreasing pitch beeps. Plays when PTT Express has lost the WLAN connection or the service is disabled.
Notification Icon
Service Indication
Talk Group
Settings
Enable/Disable Switch
Applications 4 - 25
Figure 4-15 PTT Express Default User Interface
Table 4-3 PTT Express Default User Interface Descriptions
Item Description
Notification Icon
Service Indication
Indicates the current state of the PTT Express client.
Indicates the status of the PTT Express client. Options: Service Enabled, Service
Disabled or Service Unavailable.
Talk Groups
Settings
Enable/Disable
Switch
Lists all 32 Talk Groups available for PTT communication.
Opens the PTT Express Settings screen.
Turns the PTT service on and off.
Notification Icons
Indicates the current state of the PTT Express Voice client.
4 - 26 TC75x User Guide for Android Version 6.0.1
Table 4-4 PTT Express Default User Interface Descriptions
Status Icon Description
Indicates that PTT Express Voice client is disabled.
Indicates that PTT Express Voice client is enabled but not connected to a WLAN.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and listening on the
Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and communicating on the Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and in a private response.
Indicates that PTT Express Voice client is enabled and muted.
Indicates that the PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call is in progress.
Enabling PTT Communication
1.
Touch .
2.
3.
Touch .
Slide the Enable/Disable Switch to the ON position. The button changes to an ON button.
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE
This section describes the default PTT Express client configuration. See the PTT Express V1.2 User
Guide for detailed information on using the client.
PTT communication may be established as a Group Call. When PTT Express is enabled, the PTT button on the left side of the device is assigned for PTT communication.When the Wired Headset is used, Group Calls can also be initiated using the headset Talk button.
Applications 4 - 27
PTT Button
Figure 4-16 PTT Buttons
Creating a Group Call
1.
2.
Press and hold the PTT button (or the Talk button on the headset) and listen for the talk tone to play.
If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
Start talking after the talk tone is heard.
3.
NOTE
If the user holds the button for more than 60 seconds (default), the call is dropped allowing others to make
Group calls. The user should release the button when finished talking to allow others to make calls.
Release the button when finished talking.
Responding with a Private Response
1.
2.
3.
The Private Response can only be initiated once a Group Call has been established. The initial Private Response is made to the originator of the Group Call.
4.
5.
Wait until an access tone is heard.
Within 10 seconds, double-press the PTT button, and listen for the talk tone to play.
If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
Start talking after the talk tone plays.
Release the button when finished talking.
Disabling PTT Express Voice Client Communication
1.
Touch .
2.
3.
Touch .
Slide the Enable/Disable Switch to the OFF position. The button changes to OFF.
4.
Touch .
4 - 28 TC75x User Guide for Android Version 6.0.1
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics. It allows for custom plug-ins to be created and work seamlessly with this tool. RxLogger is used to diagnose device and application issues. Its information tracking includes the following: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat,
FTP push/pull, ANR dumps, etc. All logs and files generated are saved onto flash storage on the device (internal or external).
Figure 4-17 RxLogger
Applications 4 - 29
Elemez
NOTE
Elemez
collects specific device information in the background and sends this information to us to help improve product functionality. This feature can be disabled. See
Disabling Elemez Data Collection on page 4-29
Use Elemez to provide diagnostics information to Zebra. Touch Submit Diagnostics button to send the data.
Figure 4-18 Elemez Application
Disabling Elemez Data Collection
The user can disable the Elemez application from collection specific data in the background and sending it to
Zebra Technologies.
5.
6.
7.
8.
1.
2.
3.
4.
From the Home screen, touch .
Touch Apps.
Scroll through the list and touch Elemez.
Touch FORCE STOP.
Touch OK.
Touch Disable.
Touch DISABLE APP.
Touch OK.
4 - 30 TC75x User Guide for Android Version 6.0.1
9.
Touch .
Enabling Elemez Data Collection
The user can re-enable the Elemez application for collection specific data in the background and sending it to
Zebra Technologies.
1.
2.
3.
4.
From the Home screen, touch .
Touch Apps.
Scroll through the list and touch Elemez.
Touch Enable.
5.
Touch .
6.
Touch .
7.
8.
Touch .
Touch Enable Elemez.
CHAPTER 5 DATA CAPTURE
The TC70x/TC75x supports data capture using:
•
integrated imager
•
RS507 Hands-free Imager
•
RS6000 Bluetooth Ring Scanner
•
DS3678 Digital Scanner.
Imaging
The TC70x/TC75x with an integrated 2D imager has the following features:
•
Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal,
PDF417, and 2D matrix code types.
•
The ability to capture and download images to a host for a variety of imaging applications.
•
Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a bar code, stores the resulting image in its memory, and executes state-of-the-art software decoding algorithms to extract the bar code data from the image.
Operational Modes
The TC70x/TC75x with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing the Scan button.
•
Decode Mode: In this mode, the TC70x/TC75x attempts to locate and decode enabled bar codes within its field of view. The imager remains in this mode as long as the user holds the scan button, or until it decodes a bar code.
NOTE
To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
•
Pick List Mode: This mode allows the user to selectively decode a bar code when more than one bar code is in the TC70x/TC75x’s field of view. To accomplish this, move the aiming crosshair or dot over the required bar code to decode only this bar code. This feature is ideal for pick lists containing multiple bar codes and manufacturing or transport labels containing more than one bar code type (either 1D or 2D).
5 - 2 TC75x User Guide for Android Version 6.0.1
RS507 Hands-Free Imager
The RS507 Hands-free Imager is a wearable bar code scan solution for both 1D and 2D bar code symbologies.
The scanner supports Bluetooth Human Interface Device (HID) connection to the device.
Figure 5-1 RS507 Hands-Free Imager
See to the RS507 Hands-free Imager Product Reference Guide for more information.
RS6000 Bluetooth Ring Scanner
The RS6000 Bluetooth Ring Scanner is a wearable bar code scan solution for both 1D and 2D bar code symbologies.
Figure 5-2 RS6000 Bluetooth Ring Scanner
See to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
DS3678 Digital Scanner
The cordless DS3678 combines superior 1D and 2D omnidirectional bar code scanning performance and advanced ergonomics in a lightweight design. See the DS36X8 Product Reference Guide for more information.
Data Capture 5 - 3
Figure 5-3 DS3678 Digital Scanner
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode and a few quick trial efforts master it. However, consider the following to optimize scanning performance:
•
Range: Any scanning device decodes well over a particular working range — minimum and maximum distances from the bar code. This range varies according to bar code density and scanning device optics.
Scanning within range brings quick and constant decodes; scanning too close or too far away prevents decodes. Move the scanner closer and further away to find the right working range for the bar codes being scanned.
•
Angle: Scanning angle is important for promoting quick decodes. When laser beams reflect directly back into the scanner from the bar code, this specular reflection can “blind” the scanner. To avoid this, scan the bar code so that the beam does not bounce directly back. But don’t scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
•
Hold the TC70x/TC75x farther away for larger symbols
•
Move the TC70x/TC75x closer for symbols with bars that are close together.
NOTE
Scanning procedures depend on the application and TC70x/TC75x configuration. An application may use different scanning procedures from the one listed above.
Bar Code Scanning with Internal Imager
To read a bar code, a scan-enabled application is required. The TC70x/TC75x contains the DataWedge application that allows the user to enable the imager, decode the bar code data and display the bar code content.
1.
2.
Ensure that an application is open on the TC70x/TC75x and a text field is in focus (text cursor in text field).
Point the exit window on the top of the TC70x/TC75x at a bar code.
5 - 4 TC75x User Guide for Android Version 6.0.1
Figure 5-4 Imager Scanning
3.
Press and hold the scan button.
The red laser aiming pattern turns on to assist in aiming.
4.
NOTE
When the TC70x/TC75x is in Picklist mode, the imager does not decode the bar code until the crosshair or aiming dot touches the bar code.
Ensure the bar code is within the area formed by the crosshairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
Figure 5-5 Internal Imager Aiming Pattern
Figure 5-6 Internal Imager Pick List Mode with Multiple Bar Codes in Aiming Pattern
Data Capture 5 - 5
5.
6.
The Data Capture LED lights green and a beep sounds, by default, to indicate the bar code was decoded successfully.
Release the scan button.
7.
NOTE
Imager decoding usually occurs instantaneously. The TC70x/TC75x repeats the steps required to take a digital picture (image) of a poor or difficult bar code as long as the scan button remains pressed.
The bar code content data displays in the text field.
Bar Code Capture with RS507 Hands-Free Imager
Pair the RS507 with the TC70x/TC75x. See
Pairing Using Simple Serial Interface on page 5-10
or
Bluetooth Human Interface Device on page 5-11
for more information.
1.
2.
Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
Point the RS507 at a bar code.
Figure 5-7 Bar Code Scanning with RS507
3.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The RS507 LEDs light green, a beep sounds to indicate the bar code was decoded successfully. Note that when the RS507 is in Pick List Mode, the RS507 does not decode the bar code until the center of the crosshair touches the bar code.
5 - 6 TC75x User Guide for Android Version 6.0.1
Figure 5-8 RS507 Aiming Pattern
Figure 5-9 RS507 Pick List Mode with Multiple Bar Codes in Aiming Pattern
4.
The captured data appears in the text field.
Bar Code Capture with RS6000 Bluetooth Ring Scanner
To read a bar code, a scan-enabled application is required. The TC70x/TC75x contains the DataWedge application that allows the user to enable the scanner to decode bar code data and display the bar code content.
See DataWedge Demonstration on page 4-20 for more information on launching DataWedge.
Pair the RS6000 with the TC70x/TC75x. See
Pairing Using Simple Serial Interface on page 5-10
or
Bluetooth Human Interface Device on page 5-11
1.
Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
2.
Point the RS6000 at a bar code.
Data Capture 5 - 7
Figure 5-10 Bar Code Scanning with RS6000
3.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The RS6000 LEDs light green, a beep sounds to indicate the bar code was decoded successfully. Note that when the RS6000 is in Pick List Mode, the RS6000 does not decode the bar code until the center of the crosshair touches the bar code.
Figure 5-11 RS6000 Aiming Pattern
Figure 5-12 RS6000 Pick List Mode with Multiple Bar Codes in Aiming Pattern
4.
The captured data appears in the text field.
Bar Code Capture with DS3678 Bluetooth Scanner
Pair the DS3678 with the TC70x/TC75x. See
Pairing the DS3678 Digital Scanner on page 5-12
for more information.
5 - 8 TC75x User Guide for Android Version 6.0.1
1.
2.
Ensure that an application is open on the device and a text field is in focus (text cursor in text field).
Point the DS3678 at a bar code.
Figure 5-13 Bar Code Scanning with DS3678 (-SR shown)
3.
Press and hold the trigger.
Ensure the bar code is within the area formed by the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions. The aiming dot is used for increased visibility in bright lighting conditions.
Figure 5-14 DS3678-SR Aiming Pattern
Figure 5-15 DS3678-SR Pick List Mode with Multiple Bar Codes in Aiming Pattern
4.
The captured data appears in the text field.
Pairing the RS507/RS6000 Hands-Fee Imager
To connect the RS507 or RS6000 imagers to the TC70x/TC75x, use one of the following methods:
•
Near Field Communication (NFC) (RS6000 only)
•
Simple Serial Interface (SSI)
Data Capture 5 - 9
•
Bluetooth Human Interface Device (HID) Mode.
Pairing Using Near Field Communication
The TC70x/TC75x provides the ability to pair the RS6000 using NFC.
NOTE
RS6000 only.
1.
2.
Ensure that the RS6000 is in SSI mode. Refer to the RS6000 User Guide for more information.
Ensure that NFC is enabled on the TC70x/TC75x.
3.
Align the NFC icon on the RS6000 with the NFC antenna on the TC70x/TC75x.
NFC Logo
NFC Antenna Area
Figure 5-16 Align NFC Antennas
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the
TC70x/TC75x. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the TC70x/TC75x screen and the icon appears in the Status bar.
Pairing in HID Mode Using Near Field Communication
The TC70x/TC75x provides the ability to pair the RS6000 in HID Mode using NFC.
NOTE
RS6000 only.
1.
Ensure that NFC is enabled on the TC70x/TC75x.
2.
Ensure that Bluetooth is enabled on the TC70x/TC75x.
3.
Place the RS6000 in Human Interface Device (HID) mode. If the RS6000 is already in HID mode, skip to step
3.
a.
b.
Remove the battery from the RS6000.
Press and hold the Restore key.
c.
d.
Install the battery onto the RS6000.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
5 - 10 TC75x User Guide for Android Version 6.0.1
e.
Scan the bar code below to place the RS6000 in HID mode.
Figure 5-17 RS6000 Bluetooth HID Bar Code
4.
Remove the battery from the RS6000.
5.
Re-install the battery into the RS6000.
6.
Align the NFC icon on the RS6000 with the NFC antenna on the TC70x/TC75x.
NFC Logo
NFC Antenna Area
Figure 5-18 Align NFC Antennas
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the
TC70x/TC75x. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the screen and the icon appears in the Status bar.
Pairing Using Simple Serial Interface
To pair the RS507/RS6000 with the TC70x/TC75x using SSI.
1.
On the TC70x/TC75x touch .
2.
Touch .
Data Capture 5 - 11
Figure 5-19 Bluetooth Pairing Utility
3.
Using the RS507/RS6000, scan the bar code on the screen.
The RS507/RS6000 emits a high/low/high/low beeps. The Scan LED flashes green indicating that the
RS507RS6000 is attempting to establish connection with the TC70x/TC75x. When connection is established, the Scan LED turns off and the RS507/RS6000 emits one string of low/high beeps.
A notification appears on the screen and the icon appears in the Status bar.
Pairing Using Bluetooth Human Interface Device
To pair the RS507/RS6000 with the TC70x/TC75x using HID:
1.
Ensure that Bluetooth is enabled on both devices.
2.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
4.
Place the RS507/RS6000 in Human Interface Device (HID) mode. If the RS507/RS6000 is already in HID mode, skip to step 5.
a.
b.
Remove the battery from the RS507/RS6000.
Press and hold the Restore key.
c.
d.
e.
Install the battery onto the RS507/RS6000.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
Scan the bar code below to place the RS507/RS6000 in HID mode.
5 - 12 TC75x User Guide for Android Version 6.0.1
Figure 5-20 RS507 Bluetooth HID Bar Code
Figure 5-21 RS6000 Bluetooth HID Bar Code
5.
Remove the battery from the RS507/RS6000.
6.
Re-install the battery into the RS507/RS6000.
7.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
8.
9.
Touch SCAN FOR DEVICES. The TC70x/TC75x begins searching for discoverable Bluetooth devices in the area and displays them under AVAILABLE DEVICES.
10.
Scroll through the list and select RS507 or RS6000.
The TC70x/TC75x connects to the RS507/RS6000 and Connected appears below the device name. The
Bluetooth device is added to the Bluetooth devices list and a trusted (“paired”) connection is established.
A notification appears on the screen and the icon appears in the Status bar.
Pairing the DS3678 Digital Scanner
To connect the DS3678 Digital Scanner to the TC70x/TC75x using Bluetooth Human Interface Device (HID) Mode.
Pairing Using Bluetooth Human Interface Device
To pair the DS3678 with the TC70x/TC75x using HID:
1.
Remove the battery from the DS3678 scanner.
2.
Replace the battery.
3.
After the DS3678 reboots, scan the bar code below to place the DS3678 in HID mode.
Figure 5-22 Bluetooth HID Classic Bar Code
4.
On the TC70x/TC75x, swipe down with two fingers from the status bar to open the quick access panel and then touch .
Data Capture 5 - 13
5.
6.
Touch SCAN FOR DEVICES. The TC70x/TC75x begins searching for discoverable Bluetooth devices in the area and displays them under Available devices.
7.
Scroll through the list and select DS3678 xxxxxx, where xxxxxx is the serial number.
The TC70x/TC75x connects to the DS3678, the DS3678 beeps once and Connected appears below the device name. The Bluetooth device is added to the Bluetooth devices list and a trusted (“paired”) connection is established.
DataWedge
DataWedge is a utility that adds advanced bar code scanning capability to any application without writing code. It runs in the background and handles the interface to built-in bar code scanners. The captured bar code data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
To configure DataWedge refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1.
Enabling DataWedge
1.
2.
3.
Touch Settings.
Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
4.
Touch .
Disabling DataWedge
1.
2.
3.
Touch Settings.
Touch the DataWedge enabled checkbox. The blue checkmark disappears from the checkbox indicating that
DataWedge is disabled.
4.
Touch .
5 - 14 TC75x User Guide for Android Version 6.0.1
CHAPTER 6 WIRELESS
This section provides information on the wireless features:
•
Wireless Wire Area Network (WWAN)
•
Wireless Local Area Network (WLAN)
•
Bluetooth
•
Near Field Communications (NFC).
Wireless Wide Area Networks
NOTE
TC75x only.
Use Wireless wide area networks (WWANs) to access data over a cellular network. This section provides information on:
•
Sharing a data connection
•
Disabling data roaming
•
Monitoring data usage
•
Limiting connections to 2G networks
•
Locking a SIM card
•
Editing Access Point Names (APNs).
Sharing the Mobile Data Connection
The tethering & portable hotspot settings allow you to share your data connection. You can share the TC75x’s mobile data connection with a single computer via USB tethering or Bluetooth tethering. You can also share the data connection with up to eight devices at once, by turning it into a portable Wi-Fi hotspot. While the TC75x is sharing its data connection, an icon appears at the top of the screen and a corresponding message appears in the notification list.
6 - 2 TC75x User Guide for Android Version 6.0.1
USB Tethering
1.
NOTE
USB tethering is not supported on computers running Mac OS. If your computer is running Windows 7 or a recent version of Linux (such as Ubuntu), follow these instructions without any special preparation. If running a version of Windows that precedes Windows 7, or some other operating system, you may need to prepare the computer to establish a network connection via USB.
Connect the TC75x to a host computer with the USB cable.
A USB icon appears at the top of the screen, and the notification Connected as a media device or
Connected as a camera appears briefly at the top of the screen.
2.
3.
4.
5.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ....
Touch Tethering & portable hotspot.
Touch the USB tethering.
The host computer is now sharing the TC75x’s data connection.
To stop sharing the data connection, touch the USB tethering switch again or disconnect the USB cable.
Bluetooth Tethering
Use Bluetooth tethering to share the data connection with a host computer.
Configure the host computer to obtain its network connection using Bluetooth. For more information, see the host computer’s documentation.
1.
Pair the TC75x with the host computer.
2.
3.
4.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Tethering & portable hotspot.
Touch the Bluetooth tethering switch to enable.
The host computer is now sharing the TC75x’s data connection.
To stop sharing the data connection, touch the Bluetooth tethering switch again.
Portable Wi-Fi Hotspot
Configure the Wi-Fi Hotspot settings.
1.
2.
3.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Tethering & portable hotspot.
Touch the Portable Wi-Fi hotspot switch to enable.
After a moment, the TC75x starts broadcasting its Wi-Fi network name (SSID), so you can connect to it with up to eight computers or other devices. The Hotspot icon appears in the Status Bar.
To stop sharing the data connection, touch the Portable Wi-Fi hotspot switch again.
Configuring the Wi-Fi Hotspot
1.
2.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Tethering & portable hotspot > Set up Wi-Fi hotspot.
Wireless 6 - 3
Figure 6-1 Set up Wi-Fi Hotspot Dialog Box
3.
4.
5.
6.
7.
In the Network name text field, edit the name for the hotspot.
In the Select AP Band drop-down list, select 2.4 GHz Band.
Touch the Channel option and select a channel number from the drop-down list.
Touch the Security option and select a security method from the drop-down list.
•
None
•
WPA2 PSK
In the Password text field, enter a password.
NOTE
If
None
is selected in the
Security
option, a password is not required.
8.
Touch Save.
Cellular Network Settings
Disabling Data When Roaming
To prevent the device from transmitting data over other carriers’ mobile networks when leaving an area that is covered by the carrier’s networks. This is useful for controlling expenses if the service plan does not include data roaming.
CDMA Devices
1.
2.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular networks > Data roaming access.
6 - 4 TC75x User Guide for Android Version 6.0.1
Figure 6-2 Data Roaming Access Dialog Box
3.
Select the roaming option and then touch OK.
GSM Devices
1.
2.
3.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular networks > Data roaming access.
Slide the Data roaming switch to the off position.
Preferred Network Type
Use to change the network operating mode.
1.
2.
3.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular Networks > Preferred network type.
In the Preferred network type dialog box, select a mode to set as default. Options: LTE only, Automatic or
CDMA only.
4.
Touch .
Enhanced 4G LTE Mode
Use LTE services to improve voice and other communication. (default - disabled).
Wireless 6 - 5
Search for MicroCell
A MicroCell acts like a mini cell tower is a building or residence and connects to an existing broadband Internet service. It improves cell signal performance for voice calls, texts, and cellular data applications like picture messaging and Web surfing.
1.
2.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular Networks > Search for MicroCell.
System Select
Use System select to change the CDMA roaming mode.
1.
2.
3.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular Networks > System select.
In the System select dialog box, select a mode. Options:.
•
Home only - Do not roam from Home network.
•
Automatic - Allow automatic roaming.
4.
Touch .
Editing the Access Point Name
NOTE
Many service provider Access Point Name (APN) data are pre-configured in the device. The APN information for all other service provides must be obtained from the wireless service provider.
To use the data on a network the user must configure the APN information.
1.
2.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch More ... > Cellular networks > Access Point Names.
3.
4.
Touch an APN name in the list to edit an existing APN or touch to create a new APN.
Touch each APN setting and enter the appropriate data obtained from the wireless service provider.
5.
6.
7.
When finished, touch .
Touch Save.
Touch the radio button next to the APN name to start using it.
8.
Touch .
Locking the SIM Card
Locking the SIM card requires the user to enter a PIN every time the device is turned on. If the correct PIN is not entered, only Emergency calls can be made.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
Touch Set up SIM/RUIM card lock.
Touch Lock SIM card.
6 - 6 TC75x User Guide for Android Version 6.0.1
Figure 6-3 Enter PIN to Lock SIM Card
5.
6.
Enter the PIN associated with the card. Touch OK.
Reset the device.
Data Usage
1.
Data usage refers to the amount of data uploaded or downloaded by the TC75x during a given period.
Depending on the wireless plan, you may be charged additional fees when your data usage exceeds your plan's limit. To monitor your data usage, swipe down with two fingers from the status bar to open the quick access panel and then touch .
CAUTION
The usage displayed on the data usage settings screen is measured by your device. Your carrier's data usage accounting may differ. Usage in excess of your carrier plan's data limits can result in steep overage charges. The feature described here can help you track your usage, but is not guaranteed to prevent additional charges.
Data usage settings allow you to:
•
Set the data usage level at which you'll receive a warning.
•
Set a data usage limit.
•
View or restrict data usage by app.
•
Identify mobile hotspots and restrict background downloads that may result in extra charges.
By default, when you open the data usage settings screen you see the settings for mobile data: that is, the data network or networks provided by your carrier:
Wireless 6 - 7
Figure 6-4 Data Usage Screen
To display Wi-Fi data usage settings in a separate tab touch > Show Wi-Fi.
Just below the on-off switch, note the data usage cycle. Touch it to choose a different cycle. This date range is the period of time for which the graph displays data usage.
The vertical white lines on the graph show a period of time within the data usage cycle. This range determines the usage amount displayed just below the graph. Drag lines to change the period.
Set Data Usage Warning
Drag the orange line by its right side to the level where you want to receive a warning. When your data usage reaches this level, you'll receive a notification.
Set Auto-Sync
You can also conserve data usage by syncing your apps manually, only when you need the data, rather than relying on auto-sync. To turn auto-sync off or on, touch > Restrict background data.
Wireless Local Area Networks
Wireless local area networks (WLANs) allow the TC70x/TC75x to communicate wirelessly inside a building. Before using the TC70x/TC75x on a WLAN, the facility must be set up with the required hardware to run the WLAN
(sometimes known as infrastructure). The infrastructure and the TC70x/TC75x must both be properly configured to enable this communication.
6 - 8 TC75x User Guide for Android Version 6.0.1
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches, Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wireless & networks settings configure the TC70x/TC75x to match the security scheme.
The TC70x/TC75x supports the following WLAN security options:
•
Open
•
Wireless Equivalent Privacy (WEP).
•
Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK).
•
Extensible Authentication Protocol (EAP).
The Status bar displays icons that indicate Wi-Fi network availability and Wi-Fi status. See Status Bar for more information.
NOTE
Turn off Wi-Fi when not using it, to extend the life of the battery.
Scan and Connect to a Wi-Fi Network
1.
Swipe down with two fingers from the status bar to open the quick access panel.
Figure 6-5 Quick Access Panel
2.
Touch WLAN to open the WLAN screen. The TC70x/TC75x searches for WLANs in the area and lists them.
Wireless 6 - 9
Figure 6-6 WLAN Screen
3.
4.
5.
Scroll through the list and select the desired WLAN network.
For open networks, touch profile once or press and hold and then select Connect to network or for secure networks enter the required password or other credentials then touch Connect. See the system administrator for more information.
The TC70x/TC75x obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the TC70x/TC75x with a fixed internet protocol (IP) address, refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1.
In the Wi-Fi setting field, Connected appears indicating that the TC70x/TC75x is connected to the WLAN.
Remove a Wi-Fi Network
To remove a remembered or connected network:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
In the Wi-Fi list, touch and hold the name of the network.
In the menu, touch Forget network.
5.
Touch .
6 - 10 TC75x User Guide for Android Version 6.0.1
Bluetooth
Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band
(802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 meters (32.8 feet)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (e.g., files, appointments, and tasks) with other
Bluetooth enabled devices such as printers, access points, and other mobile devices.
The TC70x/TC75x support Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with
Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work.
There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
•
Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
•
Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
•
Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
•
Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows Enterprise devices to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 meters (32.8 ft.). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space.
NOTE
It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The
Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction. Bluetooth allows for a PIN or passkey used to create other 128-bit keys used for security and encryption. The encryption key is derived from the link key used to
Wireless 6 - 11 authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the
Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
•
Perform pairing in a secure environment
•
Keep PIN codes private and do not store the PIN codes in the device
•
Implement application-level security.
Bluetooth Profiles
The device supports the following Bluetooth services:
•
Service Discovery Protocol (SDP) - Handles the search for known and specific services as well as general services.
•
Serial Port Profile (SPP) - Allows use of RFCOMM protocol to emulate serial cable connection between two
Bluetooth peer devices. For example, connecting the device to a printer.
•
Object Push Profile (OPP) - Allows the device to push and pull objects to and from a push server.
•
Advanced Audio Distribution Profile (A2DP) - Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
•
Audio/Video Remote Control Profile (AVRCP) - Allows the device to control A/V equipment to which a user has access. It may be used in concert with A2DP.
•
Personal Area Network (PAN) - Allows the use of Bluetooth Network Encapsulation Protocol to provide L3 networking capabilities over a Bluetooth link. Only PANU role is supported.
•
Human Interface Device Profile (HID) - Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
•
Headset Profile (HSP) - Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
•
Hands-Free Profile (HFP) - Allows car hands-free kits to communicate with the device in the car.
•
Out of Band (OOB) - Allows exchange of information used in the pairing process. Pairing is completed using the Bluetooth radio, but requires information from the OOB mechanism. Using OOB with NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
•
Phone Book Access Profile (PBAP) - Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so the user can initiate a call from the car display.
•
Object Push Profile (OPP) - Allows the TC70x/TC75x to push and pull objects to and from a push server.
•
Symbol Serial Interface Profile (SSI) - Allows for communication with RS507 Bluetooth Imager.
Bluetooth Power States
The Bluetooth radio is off by default.
•
Suspend - When the TC70x/TC75x goes into suspend mode, the Bluetooth radio stays on.
•
Airplane Mode - When the TC70x/TC75x is placed in Airplane Mode, the Bluetooth radio turns off. When
Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the
Bluetooth radio can be turned back on if desired.
6 - 12 TC75x User Guide for Android Version 6.0.1
Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.
NOTE
To achieve the best battery life turn off radios when not in use.
Enabling Bluetooth
1.
Swipe down with two fingers from the status bar to open the quick access panel.
2.
Touch to turn Bluetooth on.
3.
Touch .
Disabling Bluetooth
1.
Swipe down with two fingers from the status bar to open the quick access panel.
2.
Touch to turn Bluetooth off.
3.
Touch .
Discovering Bluetooth Device(s)
The TC70x/TC75x can receive information from discovered devices without pairing. However, once paired, the
TC70x/TC75x and a paired device exchange information automatically when the Bluetooth radio is on. To find
Bluetooth devices in the area:
1.
2.
3.
4.
5.
6.
7.
Ensure that Bluetooth is enabled on both devices.
Ensure that the Bluetooth device to discover is in discoverable mode.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Swipe down with two fingers from the status bar to open the quick access panel.
Touch Bluetooth.
Touch More Settings. The Bluetooth screen appears.
The TC70x/TC75x begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices.
8.
9.
Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
Enter a PIN in the text box and touch OK. Enter the same PIN on the other device.
10.
For Simple Pairing, touch Pair on both devices.
11.
The Bluetooth device is added to the Bluetooth devices list and a trusted (“paired”) connection is established.
Changing the Bluetooth Name
By default, the TC70x/TC75x has a generic Bluetooth name that is visible to other devices when connected.
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
Wireless 6 - 13
3.
If Bluetooth is not on, touch the switch to turn Bluetooth on.
4.
5.
6.
Touch .
Touch Rename device.
Enter a name and touch Rename.
7.
Touch .
Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device.
1.
2.
3.
4.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch Bluetooth.
In the list, touch the unconnected Bluetooth device.
When connected, Connected appears below the device name.
Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles. To select a profile:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
In the PAIRED DEVICES list, touch next to the device name.
Under PROFILES, check or uncheck a profile to allow the device to use that profile.
5.
Touch .
Unpairing a Bluetooth Device
To unpair a Bluetooth device and erase all pairing information:
1.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2.
3.
4.
In the PAIRED DEVICES list, touch next to the device name.
Touch FORGET.
5.
Touch .
6 - 14 TC75x User Guide for Android Version 6.0.1
Near Field Communications
NFC/HF RFID is a short-range wireless connectivity technology standard that enables secure transaction between a reader and a contactless smartcard. The technology is based on ISO/IEC 14443,ISO 18092, Type-A, Type-B,
Type-F, and ISO/IEC 15693 (vicinity) standards, using the HF 13.56 MHz unlicensed band. The TC70x/TC75x support 3 operating modes:
•
Reader mode
•
Peer-to-Peer communication
•
Card Emulation mode.
Using NFC, the TC70x/TC75x can:
•
Read contactless cards such as contactless tickets, ID cards and ePassport.
•
Read and write information to contactless cards such as SmartPosters and tickets, as well as devices with
NFC interface such as vending machines.
•
Read information from supported medical sensors.
•
Pair with supported Bluetooth devices such as printers and headsets.
•
Exchange data with another NFC device.
•
Emulate contactless card such as payment, ticket or SmartPoster.
The TC70x/TC75x NFC antenna is uniquely positioned to read NFC cards from the top of the device while being held in the user's hand.
Reading NFC Cards
1.
2.
Launch an NFC enabled application.
Hold device as shown.
Figure 6-7 Reading Cards
3.
Move TC70x/TC75x close to the NFC card until the TC70x/TC75x detects the card.
Wireless 6 - 15
4.
Hold the card steadily until the transaction is complete (usually indicated by the application).
Sharing Information Using NFC
You can beam content like a web page, contact cards, pictures, YouTube links or location information from your screen to another device by bringing the devices together back to back.
Make sure both devices are unlocked, support NFC, and have both NFC and Android Beam turned on.
1.
2.
Open a screen that contains a web page, video, photo or contact.
Move the top of the TC70x/TC75x toward the top of the other device.
Figure 6-8 Sharing Data Using NFC
3.
When the devices connect, you hear a sound, the image on the screen reduces in size, the message Touch to
beam appears.
Touch anywhere on the screen.
The transfer begins.
6 - 16 TC75x User Guide for Android Version 6.0.1
CHAPTER 7 ACCESSORIES
This chapter provides information for using the accessories for the device.
Accessories
This table lists the accessories available for the TC70x/TC75x.
Table 7-1 Accessories
Accessory
Cradles
2-Slot Charge Only Cradle
Part Number
CRD-TC7X-SE2CPP-01
2-Slot USB/Ethernet Cradle CRD-TC7X-SE2EPP-01
5-Slot Charge Only Cradle CRD-TC7X-SE5C1-01
4-Slot Charge Only Cradle with Battery Charger
CRD-TC7X-SE5KPP-01
5-Slot Ethernet Cradle CRD-TC7X-SE5EU1–01
Description
Provides device and spare battery charging.
Use with power supply, p/n PWRS-14000-148R.
Provides device and spare battery charging and
USB communication with a host computer and
Ethernet communication with a network. Use with power supply, p/n PWRS-14000-148R.
Charges up to five devices. Use with power supply, p/n PWRS-14000-241R and DC line cord, p/n 50-16002-029R. Can accommodate one 4-Slot Battery Charger using the Battery
Adapter Cup.
Charges up to four devices and four spare batteries. Use with power supply, p/n
PWRS-14000-241R and DC line cord, p/n
50-16002-029R.
Provides device charging and provides Ethernet communication for up to five devices. Use with power supply, p/n PWRS-14000-241R and DC line cord, p/n 50-16002-029R. Can accommodate one 4-Slot Battery Charger using the Battery Adapter Cup.
7 - 2 TC75x User Guide for Android Version 6.0.1
Table 7-1 Accessories (Continued)
Accessory
Cradle Mount
Batteries and Chargers
4,620 mAh
PowerPrecision+ battery
4-Slot Spare Battery
Charger
Battery Charger Adapter
Cup
BTRY-TC7X-46MPP-01
BTRY-TC7X-46MPP-10
SAC-TC7X-4BTYPP-01
CUP-SE-BTYADP1-01
Vehicle Solutions
Charging Cable Cup CHG-TC7X-CLA1-01
Charge Only Vehicle Cradle CRD-TC7X-CVCD1-01
TC7X Vehicle
Communication Charging
Cradle
USB I/O Hub
Part Number
BRKT-SCRD-SMRK-01
CRD-TC7X-DCVH-01
SHARE-USBH-01
TC7X Data Communication
Enabled Vehicle Cradle with
Hub Kit
CRD-TC7X-VCD1-01
CHG-AUTO-CLA1-01 Cigarette Light Adapter
Auto Charge Cable
Hard-wire Auto Charge
Cable
RAM Mount
CHG-AUTO-HWIRE1-01
RAM-B-166U
RAM Mount Base RAM-B-238U
Description
Mounts the 5-Slot Charge Only Cradle, 5-Slot
Ethernet Cradle, and 4-Slot Battery Charger to a wall or rack.
Replacement battery (single pack).
Replacement battery (10–pack).
Charges up to four battery packs. Use with power supply, p/n PWRS-14000-148R.
Allows for one 4-Slot Battery Charger to be charged and docked on the left most slot of the
5-Slot cradles (maximum one per cradle).
Provides power to the device from a cigarette lighter socket.
Charges and securely holds the device.
Requires power cable CHG-AUTO-CLA1-01 or
CHG-AUTO-HWIRE1-01, sold separately.
Provides power for operating the device when connected to the optional USB I/O Hub and securely holds the device.
Provides power to the TC7X Vehicle
Communication Charging Cradle, USB communication and Requires power cable
CHG-AUTO-CLA1-01 or
CHG-AUTO-HWIRE1-01, sold separately.
Contains the TC7X Vehicle Communication
Charging Cradle and the IUSB I/O Hub.
Provides power to the Vehicle Cradle from a cigarette lighter socket.
Provides power to the Vehicle Cradle from the vehicle's power panel.
Provides window mounting option for the Vehicle
Cradle. RAM Twist Lock Suction Cup with
Double Socket Arm and Diamond Base Adapter.
Overall Length: 6.75”.
RAM 2.43" x 1.31" Diamond Ball base with 1" ball.
Accessories 7 - 3
Table 7-1 Accessories (Continued)
Accessory
Charge and Communication Cables
Charging Cable Cup
Snap-On USB Cable
Part Number
CHG-TC7X-CBL1-01
CBL-TC7X-CBL1-01
Snap-On Serial Cable CBL-TC7X-SERL1-01
Snap-On DEX Cable
Audio Accessories
Premium Headset
3.5 mm Audio Adapter
CBL-TC7X-DEX1-01
RCH51
ADP-TC7X-AUD35-01
3.5 mm Headset
3.5 mm Quick Disconnect
Adapter Cable
Scanning
Trigger Handle
HDST-35MM-PTVP-01
ADP-35M-QDCBL1-01
TRG-TC7X-SNP1-02
Carrying Solutions
Soft Holster
Rigid Holster
Hand Strap
Stylus and Coiled Tether
Power Supplies
Power Supply
SG-TC7X-HLSTR2-01
SG-TC7X-RHLSTR1-01
SG-TC7X-HSTRP2-03
SG-TC7X-STYLUS-03
PWRS-14000-249R
Power Supply PWRS-14000-148R
Description
Provides power to the device. Use with power supply, p/n PWRS-14000-249R, sold separately.
Provides power to the device and USB communication with a host computer. Use with power supply, p/n PWRS-14000-249R, sold separately.
Provides power and serial communication with a host computer. Use with power supply, p/n
PWRS-14000-249R, sold separately.
Provides electronic data exchange with devices such as vending machines.
Premium Rugged headset.
Snaps onto the device and provides audio to a wired headset with 3.5 mm plug.
Use for PTT and VoIP calls.
Provides connection to the 3.5 mm Headset.
Adds gun-style handle with a scanner trigger for comfortable and productive scanning.
TC7X soft holster.
TC7X rigid holster.
Replacement hand strap with hand strap mounting clip (3–pack).
TC7X stylus with coiled tether (3-pack).
Provides power to the device using the Snap-On
USB Cable, Snap-on Serial Cable or Charging
Cable Cup. Requires AC line cord.
Provides power to the 2–Slot cradles and 4-Slot
Spare Battery Charger. Requires AC line cord.
7 - 4 TC75x User Guide for Android Version 6.0.1
Table 7-1 Accessories (Continued)
Accessory
Power Supply
Part Number
PWRS-14000-241R
DC Line Cord 50-16002-029R
Description
Provides power to the 5-Slot Charge Only cradle and the 5-Slot Ethernet Cradle. Requires DC
Line Cord, p/n 50–16002–029R and country specific three wire grounded AC line cord sold separately.
Provides power from the power supply to the
5-Slot Charge Only Cradle and 5-Slot Ethernet
Cradle.
Accessories 7 - 5
2-Slot Charge Only Cradle
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page
.
The 2-Slot Charge Only Cradle:
•
Provides 5 VDC power for operating the device.
•
Charges the device’s battery.
•
Charges a spare battery.
Power LED
Figure 7-1 2–Slot Charge Only Cradle
Charging the Device
1.
Insert the device into the slot to begin charging.
Spare Battery
Charging LED
7 - 6 TC75x User Guide for Android Version 6.0.1
Figure 7-2 Battery Charging
2.
Ensure the device is seated properly.
Charging the Spare Battery
1.
Insert the battery into the right slot to begin charging.
Figure 7-3 Spare Battery Charging
2.
Ensure the battery is seated properly.
Accessories 7 - 7
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 7-2 Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Spare battery is charging.
Charging complete.
Fast Blinking Amber
Slow Blinking Red
Solid Red
Fast Blinking Red
Off
Indication
Error in charging; check placement of spare battery.
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
7 - 8 TC75x User Guide for Android Version 6.0.1
2-Slot USB/Ethernet Cradle
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page
.
The 2-Slot USB/Ethernet Cradle:
•
Provides 5.0 VDC power for operating the device.
•
Charges the device’s battery.
•
Charges a spare battery.
•
Connects the device to an Ethernet network.
•
Provides communication to a host computer using a USB cable.
NOTE
Remove all attachments on the device, except the hand strap, before place onto the cradle.
Power LED
Figure 7-4 2-Slot USB/Ethernet Cradle
Charging the Device
1.
Place the bottom of the device into the base.
Spare Battery
Charging LED
Accessories 7 - 9
Figure 7-5 Battery Charging
2.
3.
Rotate the top of the device until the connector on the back of the device mates with the connector on the cradle.
Ensure the device is connected properly. The charging Charging/Notification LED on the device begins blinking amber indicating that the device is charging.
Charging the Spare Battery
1.
Insert the battery into the right slot to begin charging.
7 - 10 TC75x User Guide for Android Version 6.0.1
Figure 7-6 Spare Battery Charging
2.
Ensure the battery is seated properly.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 7-3 Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Spare battery is charging.
Charging complete.
Indication
Fast Blinking Amber
Slow Blinking Red
Solid Red
Fast Blinking Red
Off
Error in charging; check placement of spare battery.
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Accessories 7 - 11
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
USB/Ethernet Communication
The 2–Slot USB/Ethernet Cradle provides both Ethernet communication with a network and USB communication with a host computer. Prior to using the cradle for Ethernet or USB communication. Ensure that the switch on the
USB/Ethernet module is set properly.
Turn the cradle over to view the module.
Figure 7-7 2–Slot USB/Ethernet Cradle Module Switch
For Ethernet communication, slide the switch to the position.
For USB communication, slide the switch to the position.
Place the switch in the center position to disable communications.
Ethernet LED Indicators
There are two LEDs on the USB/Ethernet Module RJ-45 connector. The green LED lights to indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link.
Yellow LED Green LED
Figure 7-8 LED Indicators
7 - 12 TC75x User Guide for Android Version 6.0.1
Table 7-4 USB/Ethernet Module LED Data Rate Indicators
Data Rate Yellow LED
100 Mbps
10 Mbps
On/Blink
On/Blink
Establishing Ethernet Connection
On
Off
Green LED
NOTE
Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on configuring the
Ethernet settings.
1.
2.
3.
4.
5.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch Ethernet.
Slide the Ethernet switch to the ON position.
Insert the device into a slot.
The icon appears in the Status bar.
Touch Eth0 to view Ethernet connection details.
Accessories 7 - 13
5-Slot Charge Only Cradle
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page
.
The 5-Slot Charge Only Cradle:
•
Provides 5 VDC power for operating the TC70x/TC75x.
•
Simultaneously charges up to five devices and up to four devices and on 4-Slot Battery Charger using the
Battery Charger Adapter. See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the 4-Slot Battery Charger onto the cradle.
•
Consists of a cradle base and cups that can be configured for various charging requirements.
Power LED
Figure 7-9 5-Slot Charge Only Cradle
Charging the TC75
1.
Insert the TC70x/TC75x into a slot to begin charging.
7 - 14 TC75x User Guide for Android Version 6.0.1
Figure 7-10 Battery Charging
2.
Ensure the TC70x/TC75x is seated properly.
NOTE
See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the 4-Slot
Battery Charger onto the cradle.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 7-5 Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Fast Blinking Amber
Spare battery is charging.
Charging complete.
Indication
Error in charging; check placement of spare battery.
Accessories 7 - 15
Table 7-5 Spare Battery Charging LED Indicators (Continued)
LED
Slow Blinking Red
Solid Red
Fast Blinking Red
Indication
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Off
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
7 - 16 TC75x User Guide for Android Version 6.0.1
4-Slot Charge Only Cradle with Battery Charger
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page
.
The 4-Slot Charge Only Cradle with Battery Charger:
•
Provides 5 VDC power for operating the TC70x/.
•
Simultaneously charges up to four devices and up to four spare batteries.
Power LED
Figure 7-11 4-Slot Charge Only Cradle with Battery Charger
Charging the Device
1.
Insert the TC70x/TC75x into a slot to begin charging.
Accessories 7 - 17
Figure 7-12 Battery Charging
2.
Ensure the TC70x/TC75x is seated properly.
See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the
4-Slot Battery Charger onto the cradle.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 7-6 Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Fast Blinking Amber
Spare battery is charging.
Charging complete.
Indication
Error in charging; check placement of spare battery.
7 - 18 TC75x User Guide for Android Version 6.0.1
Table 7-6 Spare Battery Charging LED Indicators (Continued)
LED
Slow Blinking Red
Solid Red
Fast Blinking Red
Indication
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Off
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
Accessories 7 - 19
5-Slot Ethernet Cradle
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page
.
The 5-Slot Ethernet Cradle:
•
Provides 5.0 VDC power for operating the device.
•
Connects the device (up to five) to an Ethernet network.
•
Simultaneously charges up to five devices and up to four devices and on 4-Slot Battery Charger using the
Battery Charger Adapter. See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the 4-Slot Battery Charger onto the cradle.
Figure 7-13 5-Slot Ethernet Cradle
1000 LED
100/10 LED
7 - 20 TC75x User Guide for Android Version 6.0.1
Charging the Device
1.
Insert the TC70x/TC75x into a slot to begin charging.
Figure 7-14 Battery Charging
2.
Ensure the TC70x/TC75x is seated properly.
Accessories 7 - 21
Figure 7-15 5-Slot Ethernet Cradle with 4-Slot Battery Charger
NOTE
See the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the 4-Slot
Battery Charger onto the cradle.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 7-7 Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Fast Blinking Amber
Spare battery is charging.
Charging complete.
Indication
Error in charging; check placement of spare battery.
7 - 22 TC75x User Guide for Android Version 6.0.1
Table 7-7 Spare Battery Charging LED Indicators (Continued)
LED
Slow Blinking Red
Solid Red
Fast Blinking Red
Indication
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Off
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
Establishing Ethernet Connection
NOTE
Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on configuring the
Ethernet settings.
1.
2.
3.
4.
5.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch Ethernet.
Slide the Ethernet switch to the ON position.
Insert the device into a slot.
The icon appears in the Status bar.
Touch Eth0 to view Ethernet connection details.
LED Indicators
There are two green LEDs on the side of the cradle. These green LEDs light and blink to indicate the data transfer rate.
Table 7-8 LED Data Rate Indicators
Data Rate
1 Gbps
100 Mbps
10 Mbps
On/Blink
Off
Off
1000 LED
Off
On/Blink
On/Blink
100/10 LED
Accessories 7 - 23
4-Slot Battery Charger
CAUTION
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 8-1
This section describes how to use the 4-Slot Battery Charger to charge up to four TC70x/TC75x batteries.
Charging Spare Batteries
1.
2.
Connect the charger to a power source.
Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact.
Battery
Battery
Charge LED
Battery Slot
Figure 7-16 4-Slot Battery Charger
Battery Charging
Spare Battery Charging
Each Battery Charging LED indicates the status of the battery charging in each slot. The table below describes the
Battery Charging LED status.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
7 - 24 TC75x User Guide for Android Version 6.0.1
Table 7-9 Battery LED Charging Indicators
LED
Slow Blinking Amber
Solid Green
Spare battery is charging.
Charging complete.
Fast Blinking Amber
Slow Blinking Red
Solid Red
Fast Blinking Red
Off
Indication
Error in charging; check placement of spare battery.
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The battery charger always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the battery charger may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The battery charger indicates when charging is disabled due to abnormal temperatures via its LED.
Accessories 7 - 25
3.5 mm Audio Adapter
The 3.5 mm Audio Adapter snaps onto the back of the TC70x/TC75x and removes easily when not in use. When attached to the TC70x/TC75x the 3.5 mm Audio Adapter allows a user to connect a wired headset to the
TC70x/TC75x.
Connecting a Headset to the 3.5 mm Audio Adapter
1.
Connect the Quick Disconnect connect of the headset to the Quick Disconnect connector of the 3.5 mm Quick
Disconnect Adapter Cable.
Figure 7-17 Connect Headset to Adapter Cable
2.
Connect the audio jack of the 3.5 mm Quick Disconnect Adapter Cable to the 3.5 mm Audio Adapter.
Figure 7-18 Connect Adapter Cable to Audio Adapter
7 - 26 TC75x User Guide for Android Version 6.0.1
Attaching the 3.5 mm Audio Adapter
1.
Align the top mounting points on the 3.5 mm Audio Adapter with the mounting slots on the TC70x/TC75x.
Figure 7-19 Audio Adapter Installation
2.
Rotate the Audio Adapter down and press down until it snaps into position.
Device with 3.5 mm Audio Adapter in Holster
When using the TC70x/TC75x and the audio adapter in a holster, ensure that the display faces in and the headset cable is securely attached to the audio adapter.
Figure 7-20 Device with 3.5 mm Audio Adapter in Holster
Removing the 3.5 mm Audio Adapter
1.
Disconnect headset plug from 3.5 mm Audio Adapter.
2.
Lift the bottom of the Audio Adapter away from the device.
Accessories 7 - 27
Figure 7-21 Remove Audio Adapter from Device
3.
Remove Audio Adapter from the TC70x/TC75x.
7 - 28 TC75x User Guide for Android Version 6.0.1
Snap-On USB Cable
The Snap-On USB Cable snaps on to the back of the TC70x/TC75x and removes easily when not in use. When attached to the TC70x/TC75x the Snap-On USB Cable allows the TC70x/TC75x to transfer data to a host computer and provide power for charging the TC70x/TC75x.
Connecting to Device
1.
Align the top mounting points on the cable with the mounting slots on the TC70x/TC75x.
Figure 7-22 Cable Installation
2.
Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the TC70x/TC75x.
Figure 7-23 Cable Attached to TC75
USB Communication
1.
Connect the Snap-On USB Cable to the TC70x/TC75x.
Figure 7-24 Cable Removed from Device
2.
Connect the USB connector of the cable to a host computer.
Charging the Device
1.
2.
Connect the Snap-On USB Cable to the TC70x/TC75x.
Connect the power supply to the Snap-On USB Cable
Figure 7-25 Power Setup
3.
Connect to the power supply to an AC outlet.
Disconnecting from Device
1.
Press down on the cable.
Accessories 7 - 29
7 - 30 TC75x User Guide for Android Version 6.0.1
Figure 7-26 Press Down on Cable
2.
Rotate away from the TC70x/TC75x. The magnetics release the cable from the TC70x/TC75x.
Figure 7-27 Remove Cable from Device
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device indicates when charging is disabled due to abnormal temperatures via its LED.
Charging Cable Cup
This section describes how to use the Charging Cable Cup to charge the device.
Charging the Device
1.
Insert the TC70x/TC75x into the cup of the Charging Cable Cup.
Accessories 7 - 31
Figure 7-28 Charging
2.
3.
Ensure the TC70x/TC75x is seated properly.
Slide the two yellow locking tabs up to lock the cable to the TC70x/TC75x.
Figure 7-29 Lock Cable Cup
4.
Connect the power supply to the Charging Cable Cup and to a power source.
7 - 32 TC75x User Guide for Android Version 6.0.1
Figure 7-30 Connect Cable to Power Supply
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device indicates when charging is disabled due to abnormal temperatures via its LED.
Accessories 7 - 33
Snap-On DEX Cable
The Snap-On DEX Cable snaps on to the back of the TC70x/TC75x and removes easily when not in use. When attached to the TC70x/TC75x the Snap-On DEX Cable provides electronic data exchange with devices such as vending machines.
Connecting to Device
1.
Align the top mounting points on the cable with the mounting slots on the TC70x/TC75x.
Figure 7-31 Cable Installation
2.
Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the TC70x/TC75x.
Figure 7-32 Cable Attached to Device
DEX Communication
1.
2.
Connect the Snap-On DEX Cable to the TC70x/TC75x.
Connect the DEX connector of the cable to a device such as a vending machine.
7 - 34 TC75x User Guide for Android Version 6.0.1
Figure 7-33 DEX Cable Connection
Disconnecting from Device
1.
Press down on the cable.
Figure 7-34 Press Down on Cable
2.
Rotate away from the TC70x/TC75x. The magnetics release the cable from the TC70x/TC75x.
Figure 7-35 Remove Cable from Device
Accessories 7 - 35
Trigger Handle
The Trigger Handle adds a gun-style handle with a scanning trigger to the device. It increases comfort when using the device in scan-intensive applications for extended periods of time.
Latch
Release Button
Trigger
Attachment Plate with
Tether
Figure 7-36 Trigger Handle
Installing the Attachment Plate to Trigger Handle
To install the attachment plate to the Trigger Handle:
1.
2.
Insert the loop end of the tether into the slot on the bottom of the handle.
Feed the attachment plate through the loop.
Figure 7-37 Install Attachment Plate to Handle
3.
Pull the attachment plate until the loop tightens on the tether.
Installing the Trigger Handle Plate
1.
Press and hold the Power button until the menu appears.
7 - 36 TC75x User Guide for Android Version 6.0.1
2.
3.
4.
5.
6.
Touch Power off.
Touch OK.
Press in the two battery latches.
Lift the battery from the device.
Remove the hand strap filler plate from the hand strap slot. Store the hand strap filler plate in a safe place for future replacement.
Figure 7-38 Remove Hand Strap Plate
7.
Insert the attachment plate into the hand strap slot.
Figure 7-39 Insert Trigger Handle Plate
8.
9.
Insert the battery, bottom first, into the battery compartment in the back of the device.
Rotate the top of the battery into the battery compartment.
10.
Press the battery down into the battery compartment until the battery release latches snap into place.
Inserting the Device into the Trigger Handle
1.
Align the back of the Trigger handle with the Trigger Mounting Plate.
Figure 7-40 Connect Device to Trigger Handle
2.
3.
Press the two release latches.
Rotate the device down and press down until it snaps into place.
Figure 7-41 Rotate Device onto Trigger Handle
Accessories 7 - 37
7 - 38 TC75x User Guide for Android Version 6.0.1
Removing the Device from the Trigger Handle
1.
Press both Trigger Handle release latches.
Figure 7-42 Press Release Latches
2.
3.
Rotate the device up and remove from the Trigger handle.
Rotate the device down and press down until it snaps into place.
Figure 7-43 Rotate Device onto Trigger Handle
Accessories 7 - 39
7 - 40 TC75x User Guide for Android Version 6.0.1
Vehicle Charging Cable Cup
This section describes how to use the Vehicle Charging Cable Cup to charge the TC70x/TC75x.
Figure 7-44 Vehicle Charging Cable Cup
Charging the Device
1.
Insert the TC70x/TC75x into the cup of the Vehicle Charging Cable.
Figure 7-45 Charging
2.
3.
Ensure the TC70x/TC75x is seated properly.
Slide the two yellow locking tabs up to lock the cable to the TC70x/TC75x.
Figure 7-46 Lock Cable Cup
4.
Insert the Cigarette Lighter plug into the vehicle cigarette lighter socket.
Accessories 7 - 41
7 - 42 TC75x User Guide for Android Version 6.0.1
Figure 7-47 Connect Cable to Vehicle Power Source
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C (+98°F)) the device may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device indicates when charging is disabled due to abnormal temperatures via its LED.
Accessories 7 - 43
Vehicle Cradle
Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the Vehicle
Cradle.
The cradle:
•
holds the TC70x/TC75x securely in place
•
provides power for operating the TC70x/TC75x
•
re-charges the battery in the TC70x/TC75x.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to 32V and supplies a maximum current of 3A.
Figure 7-48 Vehicle Cradle
Device Insertion and Removal
CAUTION
Ensure that the
TC70x/
TC75x is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while driving.
To ensure the TC70x/TC75x was inserted correctly, listen for the audible click that signifies that the TC70x/TC75x locking mechanism was enabled and the TC70x/TC75x was locked into place.
7 - 44 TC75x User Guide for Android Version 6.0.1
Figure 7-49 Install Device into Vehicle Cradle
To remove the TC70x/TC75x from the cradle, grasp the TC70x/TC75x and lift out of the cradle.
Figure 7-50 Remove Device from Vehicle Cradle
Accessories 7 - 45
Battery Charging
Ensure the cradle is connected to a power source.
Insert the TC70x/TC75x into the cradle. The TC70x/TC75x starts to charge through the cradle as soon as it is inserted. This does not deplete the vehicle battery significantly. The battery charges in approximately four hours.
See
for charging indications.
NOTE
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the TC70x/TC75x will only charge when its temperature is between 0°C to +40°C.
7 - 46 TC75x User Guide for Android Version 6.0.1
TC7X Vehicle Communication Charging Cradle
The Vehicle Communication Charging Cradle:
•
holds the TC70x/TC75x securely in place
•
provides power for operating the TC70x/TC75x
•
re-charges the battery in the TC70x/TC75x.
The cradle is powered by the USB I/O Hub.
Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the TC7X Vehicle
Communication Charging Cradle.
Figure 7-51 TC7X Vehicle Communication Charging Cradle
Accessories 7 - 47
Device Insertion and Removal
1
3
2
2
1
2
Figure 7-52 Insert and Remove Device into Cradle
To ensure the TC70x/TC75x was inserted correctly, listen for the audible click that signifies that the TC70x/TC75x locking mechanism was enabled and the TC70x/TC75x was locked into place.
CAUTION
Ensure that the TC70x/TC75x is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while driving.
To remove the TC70x/TC75x from the cradle, press the release latch, grasp the TC70x/TC75x and lift out of the vehicle cradle.
Device Battery Charging
Insert the TC70x/TC75x into the cradle. The TC70x/TC75x starts to charge through the cradle as soon as it is inserted. This does not deplete the vehicle battery significantly. The battery charges in approximately four hours.
See
for all charging indications.
Charging Note
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the TC70x/TC75x will only charge when its temperature is between 0°C to +40°C.
7 - 48 TC75x User Guide for Android Version 6.0.1
USB I/O Hub
The USB I/O Hub:
•
provides power to a vehicle cradle
•
provides USB hub for three USB devices (such as printers)
•
provides a powered USB port for charging another device.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to 32V and supplies a maximum current of 3Ato the vehicle cradle and 1.5 A to the four USB ports simultaneously.
Refer to the TC70x/TC75x Integrator Guide for Android Version 6.0.1 for information on installing the USB I/O Hub.
Figure 7-53 USB I/O Hub
Connect USB Cables
The USB I/O Hub provides three USB ports for connecting devices such as printers to a device in the vehicle cradle. To connect USB cables:
1.
Slide the cable cover down and remove.
Accessories 7 - 49
Figure 7-54 Remove Cover
2.
3.
Insert the USB cable connector into one of the USB ports.
Place each cable into the cable holder.
Figure 7-55 Connect USB Cable
4.
Align the cable cover onto the USB I/O Hub. Ensure that the cables are within the cover opening.
Figure 7-56 Replace Cover
5.
Slide cable cover up to lock into place.
External USB Cable
The USB I/O Hub provides a USB port for charging external devices such as cell phones. This port is for charging only.
1.
Open the USB Access Cover.
7 - 50 TC75x User Guide for Android Version 6.0.1
2.
Insert the USB cable connector into the USB port.
USB Port
Access Cover
USB Port
Figure 7-57 Insert External USB Cable
Power to Vehicle Cradle
The USB I/O Hub can provide power to a Vehicle Cradle.
1.
2.
Connect the Power Output Cable connector to the Power Input Cable connector of the Vehicle Cradle.
Tighten thumbscrews by hand until tight.
2
Vehicle Cradle Power and
Communication Connector
1
Power and
Communication
Connector
Figure 7-58 Connect Power to Vehicle Cradle
Audio Headset Connection
The USB I/O Hub provides audio connection to the device in a vehicle cradle.
Depending upon, headset, connect the headset and audio adapter to the Headset connector.
Collar
Connect Audio Headset
Headset
Adapter Cable
Accessories 7 - 51
7 - 52 TC75x User Guide for Android Version 6.0.1
CHAPTER 8 MAINTENANCE AND
TROUBLESHOOTING
This chapter includes instructions on cleaning and storing the device, and provides troubleshooting solutions for potential problems during operation.
Maintaining the Device
For trouble-free service, observe the following tips when using the TC70x/TC75x:
•
Do not scratch the screen of the TC70x/TC75x. When working with the TC70x/TC75x use the supplied stylus or plastic-tipped pens intended for use device a touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the TC75x screen.
•
The touch-sensitive screen of the TC70x/TC75x is glass. Do not to drop the TC70x/TC75x or subject it to strong impact.
•
Protect the TC70x/TC75x from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
•
Do not store or use the TC70x/TC75x in any location that is dusty, damp, or wet.
•
Use a soft lens cloth to clean the TC70x/TC75x. If the surface of the TC70x/TC75x screen becomes soiled, clean it with a soft cloth moistened with a diluted window-cleaning solution.
•
Periodically replace the rechargeable battery to ensure maximum battery life and product performance.
Battery life depends on individual usage patterns.
Battery Safety Guidelines
•
The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
•
Follow battery usage, storage, and charging guidelines found in this guide.
•
Improper battery use may result in a fire, explosion, or other hazard.
•
To charge the mobile device battery, the battery and charger temperatures must be between +32ºF and
+104ºF (0ºC and +40ºC)
•
Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact the Global Customer Support Center.
8 - 2 TC75x User Guide for Android Version 6.0.1
•
For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
•
To enable authentication of an approved battery, as required by IEEE1725 clause 10.2.1, all batteries will carry a hologram. Do not fit any battery without checking it has the authentication hologram.
•
Do not disassemble or open, crush, bend or deform, puncture, or shred.
•
Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
•
Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
•
Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
•
Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
•
Battery usage by children should be supervised.
•
Please follow local regulations to properly dispose of used re-chargeable batteries.
•
Do not dispose of batteries in fire.
•
In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
•
If you suspect damage to your equipment or battery, contact the Customer Support to arrange for inspection.
Cleaning Instructions
CAUTION
Always wear eye protection.
Read warning label on compressed air and alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support
Center for more information.
WARNING
!
Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite, hydrogen peroxide or mild dish soap.
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Maintenance and Troubleshooting 8 - 3
Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, but gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Allow the unit to air dry before use.
Special Cleaning Notes
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device. The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed. If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the plastics.
Cleaning Materials Required
•
Alcohol wipes
•
Lens tissue
•
Cotton-tipped applicators
•
Isopropyl alcohol
•
Can of compressed air with a tube.
Cleaning Frequency
The cleaning frequency is up to the customer’s discretion due to the varied environments in which the mobile devices are used. They may be cleaned as frequently as required, but it is advisable to clean the camera window periodically when used in dirty environments to ensure optimum performance.
Cleaning the TC70x/TC75x
Housing
Using the alcohol wipes, wipe the housing including buttons.
Display
The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
Camera and Exit Window
Wipe the camera and exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
Connector Cleaning
To clean the connectors:
8 - 4 TC75x User Guide for Android Version 6.0.1
4.
5.
6.
1.
2.
3.
Remove the main battery from mobile computer.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
Rub the cotton portion of the cotton-tipped applicator back-and-forth across the connector. Do not leave any cotton residue on the connector.
Repeat at least three times.
Use the cotton-tipped applicator dipped in alcohol to remove any grease and dirt near the connector area.
Use a dry cotton-tipped applicator and repeat steps 4 through 6.
CAUTION
Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.
7.
8.
Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface.
Inspect the area for any grease or dirt, repeat if required.
Cleaning Cradle Connectors
1.
2.
3.
To clean the connectors on a cradle:
4.
Remove the DC power cable from the cradle.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
All sides of the connector should also be rubbed with the cotton-tipped applicator.
CAUTION
Do not point nozzle at yourself and others, ensure the nozzle or tube is pointed away from your face.
5.
6.
7.
8.
Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away from the surface.
Remove any lint left by the cotton-tipped applicator.
If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and dry humidity requires less drying time.
Maintenance and Troubleshooting 8 - 5
Troubleshooting
The following tables provides typical problems that might arise and the solution for correcting the problem.
TC70x/TC75x
Table 8-1 Troubleshooting the TC70x/TC75x
Problem Cause
When pressing the power button the
TC70x/TC75x does not turn on.
Battery not charged.
Battery not installed properly.
System crash.
When pressing the power button the
TC70x/TC75x does not turn on but two
LEDs blink.
Battery did not charge.
Battery charge is at a level where data is maintained but battery should be re-charged.
Battery failed.
Solution
Charge or replace the battery in the TC70x/TC75x.
Install the battery properly.
Perform a reset.
Charge or replace the battery in the TC70x/TC75x.
Replace battery. If the TC70x/TC75x still does not operate, perform a reset.
TC70x/TC75x removed from cradle while battery was charging.
Insert TC70x/TC75x in cradle. The 4,620 mAh battery fully charges in less than five hours at room temperature.
Cannot see characters on display.
Extreme battery temperature.
TC70x/TC75x not powered on.
Battery does not charge if ambient temperature is below 0°C
(32°F) or above 40°C (104°F).
Press the Power button.
During data communication with a host computer, no data transmitted, or transmitted data was incomplete.
TC70x/TC75x removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Replace the TC70x/TC75x in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Communication software was incorrectly installed or configured.
Perform setup.
During data communication over
Wi-Fi, no data transmitted, or transmitted data was incomplete.
Wi-Fi radio is not on.
You moved out of range of an access point.
Turn on the Wi-Fi radio.
Move closer to an access point.
8 - 6 TC75x User Guide for Android Version 6.0.1
Table 8-1 Troubleshooting the TC70x/TC75x (Continued)
Problem
During data communication over
WAN, no data transmitted, or transmitted data was incomplete.
APN is not set up correctly.
SIM card not installed properly.
Cause
You are in an area of poor cellular service.
Solution
Move into an area that has better service.
See system administrator for APN setup information.
Remove and re-install the SIM card.
During data communication over
Bluetooth, no data transmitted, or transmitted data was incomplete.
Data plan not activated.
Contact your service provider and ensure that your data plan is enable.
Bluetooth radio is not on.
You moved out of range of another Bluetooth device.
Turn on the Bluetooth radio.
Move within 10 meters (32.8 feet) of the other device.
No sound.
TC70x/TC75x shuts off.
Volume setting is low or turned off.
Battery is depleted.
Adjust the volume.
TC70x/TC75x is inactive.
The display turns off after a period of inactivity. Set this period to 15 seconds, 30 seconds, 1, 2, 5, 10 or 30 minutes.
Replace the battery.
Reset the device.
Tapping the window buttons or icons does not activate the corresponding feature.
The device is not responding.
A message appears stating that the
TC70x/TC75x memory is full.
Too many files stored on the TC70x/TC75x.
Too many applications installed on the TC75x.
Delete unused memos and records. If necessary, save these records on the host computer (or use an SD card for additional memory).
Remove user-installed applications on the TC70x/TC75x to recover memory. Select > Apps > Downloaded.
Select the unused program and tap Remove.
Maintenance and Troubleshooting 8 - 7
Table 8-1 Troubleshooting the TC70x/TC75x (Continued)
Problem
The TC70x/TC75x does not decode with reading bar code.
Cause
Scanning application is not loaded.
Unreadable bar code.
Solution
Load a scanning application on the TC70x/TC75x or enable
DataWedge. See the system administrator.
Ensure the symbol is not defaced.
Place the TC75x within proper scanning range.
Distance between exit window and bar code is incorrect.
TC70x/TC75x is not programmed for the bar code.
TC70x/TC75x is not programmed to generate a beep.
If the TC70x/TC75x does not beep on a good decode, set the application to generate a beep on good decode.
Battery is low.
Program the TC70x/TC75x to accept the type of bar code being scanned. Refer to the EMDK or DataWedge application.
If the scanner stops emitting a laser beam upon a trigger press, check the battery level. When the battery is low, the scanner shuts off before the TC70x/TC75x low battery condition notification. Note: If the scanner is still not reading symbols, contact the distributor or the Global Customer
Support Center.
Move closer to the other Bluetooth device(s), within a range of 10 meters (32.8 feet).
Turn on the Bluetooth device(s) to find.
TC70x/TC75x cannot find any Bluetooth devices nearby.
Too far from other
Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
Cannot unlock
TC70x/TC75x.
The Bluetooth device(s) are not in discoverable mode.
User enters incorrect password.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
If the user enters an incorrect password eight times, the user is requested to enter a code before trying again.
If the user forgot the password, contact system administrator.
8 - 8 TC75x User Guide for Android Version 6.0.1
APPENDIX A TECHNICAL
SPECIFICATIONS
The following sections provide technical specification for the device.
TC70x/TC75x
Table A-1 TC70x/TC75x Technical Specifications
Item Description
Physical Characteristics
Dimensions Height: 161 mm (6.3 in.)
Width: 84 mm (3.3 in.)
Depth: 28 mm (1.1 in.)
Weight
Display
376 g (13.3 oz)
4.7 in. High Definition (1280 x 720); exceptionally bright image; optically bonded to touch panel with Gorilla Glass™ protection
Touch Panel
Backlight
Battery Pack
Expansion Slot
Connection Interface
Notification
Voice and Audio
Capacitive touch
Light Emitting Diode (LED) backlight
Rechargeable Lithium Ion 3.7V, 4,620 mAh battery
User accessible microSD up to 32 GB SDHC and up to 128 GB SDXC support
Universal Serial Bus (USB) 2.0 High Speed (host and client)
Audible tone plus multi-color LEDs, vibration
Three microphone support with noise cancellation; vibrate alert; speaker;
Bluetooth wireless headset support. High quality speaker phone with up to 108 db SPL volume; PTT headset support; Cellular circuit switch voice; HD Voice
Performance Characteristics
CPU 1.8 GHz hex core 64 bit processor (Snapdragon 650)
A - 2 TC75x User Guide for Android Version 6.0.1
Table A-1 TC70x/TC75x Technical Specifications (Continued)
Item Description
Operating System
Memory
Android 6.0 Marshmallow
2 GB RAM/16 GB Flash
USB - 5 VDC @ 500 mA max Output Power
User Environment
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop Specification
-20°C to 50°C (-4°F to 122°F)
-40°C to 70°C (-40°F to 158°F)
0° C to 40° C (32°F to 104°F)
5 to 95% non-condensing
8 ft./2.4 m to concrete at room temperature; 6 ft./1.8 m over the operating temperature range
Tumble
Electrostatic Discharge (ESD)
Sealing
Vibration
2,000 3.2 ft./1.0 m tumbles; meets and exceeds IEC tumble specifications
+/-15kVdc air discharge, +/-8kVdc direct discharge, +/-8kVdc indirect discharge
IP67 per applicable IEC sealing specifications
4 g’s PK Sine (5 Hz to 2 kHz); 0.04g2/Hz Random (20 Hz to 2 kHz); 60 minute duration per axis, 3 axis
Thermal Shock -40° C to 70° C (-40° F to 158° F) rapid transition
Interactive Sensor Technology (IST)
Motion Sensor 3-axis accelerometer provides motion-sensing for dynamic screen orientation and power management
Light Sensor Ambient light sensor to auto adjust display backlight brightness
Wireless WAN Data and Voice Communications (TC75x only)
Frequency band
GPS
Worldwide:
LTE: 700,800/850/900/1800/2100/2600 (FDD 28,20,5,8,3,1,7);
UMTS/HSPA/HSPA+: 850/900/1900/2100;
GSM/GPRS/EDGE: 850/900/1800/1900
Americas:
LTE: 700/850/1900/AWS/2100, (FDD 13,12,17,5,26,2,25,4,1);
UMTS/HSPA/HSPA+: 850, 900, AWS, 1900, 2100
GSM/GPRS/EDGE: 850/900/1800/1900;
CDMA: 850,1900 (BC0, BC10, BC1)
Integrated, Autonomous, Assisted GPS (A-GPS), Navstar, GLONASS, Beidou,
Galileo
Wireless LAN Data and Voice Communications
Radio
2x2 MIMO; IEEE
®
802.11a/b/g/n/ac/d/h/i/r
Technical Specifications A - 3
Table A-1 TC70x/TC75x Technical Specifications (Continued)
Item Description
Data Rates Supported
Operating Channels
Security
5GHz: 802.11a/n/c - up to 866.7 Mbps
2.4GHz: 802.11b/g/n - up to 144 Mbps
Chan 1 - 13 (2412 - 2472 MHz), Chan 36 - 165 (5180 - 5825 MHz)
Channel Bandwidth: 20, 40, 80 MHz
Actual operating channels/frequencies depend on regulatory rules and certification agency
WEP (40 or 104 bit); WPA/WPA2 Personal (TKIP, and AES); WPA/WPA2
Enterprise (TKIP and AES) - EAP-TTLS (PAP, MSCHAP, MSCHAPv2),
EAP-TLS, PEAPv0-MSCHAPv2, PEAPv1-EAP-GTC and LEAP
Wireless PAN Data and Voice Communications
Bluetooth Bluetooth v4.1 Low Energy
Data Capture Specifications
2D Imager
Camera
SE4750-SR – 1D and 2D bar codes.
Rear: 13 Mega pixel auto focus with flash
Front: 1.3 Mega pixel fixed focus
Near Field Communications
(NFC)
Communication and Messaging
ISO 14443 Type A ad B, FeliCa, and ISO 15963 cards. P2P mode and Card
Emulation via UICC and Host.
Workforce Connect PTT Express (included) provides instant push-to-talk (PTT) small group communications across
Wi-Fi networks. Workforce Connect PTT Pro (supported) provides a scalable network agnostic push-to-talk solution which also includes messaging, location services and two-way radio integration. Workforce Connect Voice client
(supported) enables the TC75x to function as a full featured mobile telephone with multi-line capability across Wi-Fi networks.
2D Imager Engine (SE4750-SR) Specifications
Field of View Horizontal - 48.0°
Vertical - 36.7°
Image Resolution
Roll
Pitch Angle
Skew Tolerance
Ambient Light
1280 horizontal X 960 vertical pixels
360°
+/- 60° from normal
+/- 60° from normal
Sunlight: 10,000 ft. candles (107,639 lux)
A - 4 TC75x User Guide for Android Version 6.0.1
Table A-1 TC70x/TC75x Technical Specifications (Continued)
Item Description
Focal Distance
Laser Aiming Element
Illumination System
From front of engine: 17.7 cm (7.0 in.)
Visible Laser Diode (VLD): 655 nm +/- 10 nm
Central Dot Optical Power: 0.6 mW (typical)
Pattern Angle: 48.0º horizontal, 38.0º vertical
LEDs: Warm white LED
Pattern Angle: 80° at 505 intensity
Table A-2 Data Capture Supported Symbologies
Item Description
1D Bar Codes
2D Bar Codes
Code 128, EAN-8, EAN-13, GS1 DataBar Expanded, GS1 128, GS1 DataBar
Coupon, UPCA, Interleaved 2 of 5, UPC Coupon Code
PDF-417, QR Code
INDEX
A
adaptive frequency hopping . . . . . . . . . . . . . . . . . . 6-10
adjust volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
airplane mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
albums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
approved cleanser . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
audio modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
B
battery usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Bluetooth
Bluetooth headset . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
C
call barring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
camera settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
cleaning instructions . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
conference call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
cradle
connector cleaning . . . . . . . . . . . . . . . . . . . . . . . 8-4
D
data capture options . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
datawedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
E
EAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Elemez . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
emergency calling . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Ethernet connection . . . . . . . . . . . . . . . . . . . . . . . . 7-22
F
file browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
finger usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
fixed dialing numbers . . . . . . . . . . . . . . . . . . . . . . . 3-14
Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv, i-xiv
font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
H
handset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
harmful ingredients . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
headset mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
I
imager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv, i-xiv
K
keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
L
low battery notification . . . . . . . . . . . . . . . . . . . . . . . 1-17
Index - 2 TC75x User Guide for Android Version 6.0.1
M
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
O
operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
P
panoramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
R
radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv
RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv, i-xiv
recording videos . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
ringtone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
RS507 scanning . . . . . . . . . . . . . . . . . . . . . . . . .5-5, 5-8
RS6000 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
S
screen font size . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
setting
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
software version . . . . . . . . . . . . . . . . . . . . . . . . xiv, i-xiv
speaker mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
T
taking a panoramic photo . . . . . . . . . . . . . . . . . . . . 4-10
touch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
TTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
U
using the dialer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
V
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . . . 7-46, 7-48
video settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9, 4-11
voicemail setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
W
WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
wired headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
WPA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Zebra Technologies Corporation
3 Overlook Point
Lincolnshire, IL 60069, U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2017 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. All
Rights Reserved.
MN-002881-03 Revision A - February 2017
Laadi alla
Avalik link on uuendatud
Teie vestluse avalik link on uuendatud. You may view and manage your chat links after registration here.
Dokumendi avalik link
Reklaam