Data sheet 9364880b, 80010292V03

6-Port Antenna
Frequency Range
Dual Polarization
HPBW
Adjust. Electr. DT
R1
B1
B2
790–960 1710–2180 1710–2180
X
X
X
65°
65°
65°
2°–10°
0°–10°
0°–10°
set by hand or by optional RCU (Remote Control Unit)
6-Port Antenna 790–960/1710–2180/1710–2180 65°/65°/65° 17.5/17.5/17dBi
2°–10°/0°–10°/0°–10°T
Type No.
80010292V03
Lowband
R1, connector 1– 2
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
MHz
dBi
dBi
790 – 862
17.1
17.0 ± 0.3
790 – 960
824 – 894
17.3
17.2 ± 0.3
880 – 960
17.4
17.3 ± 0.3
°
69 ± 1.1
68 ± 1.3
66 ± 1.1
dB
> 26
> 27
> 28
dB
> 25
> 25
> 27
dB
> 14.0
> 14.5
> 12.5
dB
< 2.0
< 2.0
< 2.5
°
7.9 ± 0.3
7.6 ± 0.3
7.2 ± 0.3
°
2.0 – 10.0
°
< 0.1
< 0.1
< 0.2
dB
> 14
> 15
> 15
936.4880/b ngmn 04.19.01.01 Subject to alteration.
Cross Polar Isolation
dB
> 30
Port to Port Isolation
dB
> 36 (R1 // B1, B2)
Max. Effective Power
W
400 (at 50 °C ambient temperature)
per Port
Max. Effective Power
W
800 (at 50 °C ambient temperature)
Port 1–2
Values based on NGMN-P-BASTA (version 9.6) requirements.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
80010292V03 Page 1 of 4
6-Port Antenna
Lower highband
MHz
dBi
dBi
1710 – 1880
17.2
17.1 ± 0.4
1710 – 2180
1850 – 1990
17.3
17.2 ± 0.3
1920 – 2180
17.3
17.2 ± 0.4
°
64 ± 2.6
62 ± 2.4
62 ± 2.9
dB
> 29
> 29
> 26
dB
> 31
> 30
> 29
dB
> 12.0
> 12.5
> 11.5
dB
< 0.5
< 1.0
< 1.0
°
7.6 ± 0.4
7.2 ± 0.5
6.8 ± 0.6
°
0.0 – 10.0
°
< 0.6
< 0.7
< 0.6
dB
> 14
> 17
> 16
Cross Polar Isolation
dB
Port to Port Isolation
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 3–4
Values based on NGMN-P-BASTA (version 9.6) requirements.
Upper highband
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
250 (at 50 °C ambient temperature)
500 (at 50 °C ambient temperature)
B2, connector 5 – 6
MHz
dBi
dBi
1710 – 1880
16.7
16.5 ± 0.3
1710 – 2180
1850 – 1990
16.8
16.6 ± 0.3
1920 – 2180
17.0
16.8 ± 0.3
°
66 ± 3.1
63 ± 4.0
61 ± 2.9
dB
> 28
> 30
> 27
dB
> 30
> 30
> 28
dB
> 14.5
> 14.0
> 11.0
dB
< 0.5
< 1.0
< 1.5
°
7.6 ± 0.3
7.2 ± 0.4
6.9 ± 0.5
°
0.0 – 10.0
°
< 0.4
< 0.5
< 0.6
dB
> 16
> 16
> 16
Cross Polar Isolation
dB
Port to Port Isolation
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 5–6
Values based on NGMN-P-BASTA (version 9.6) requirements.
Page 2 of 4 80010292V03
> 30
> 36 (B1 // R1, B2)
> 30
> 36 (B2 // R1, B1)
250 (at 50 °C ambient temperature)
500 (at 50 °C ambient temperature)
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
936.4880/b ngmn 04.19.01.01 Subject to alteration.
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
B1, connector 3 – 4
6-Port Antenna
Mechanical specifications
Electrical specifications, all systems
Impedance
Ω
50
VSWR
< 1.5
Return Loss
dB
> 14
Interband Isolation
dB
> 36
Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)
Polarization
°
+45, –45
900 (at 50 °C ambient
Max. Effective Power
W
temperature)
for the Antenna
Values based on NGMN-P-BASTA (version 9.6) requirements.
Input
Connector Position
Adjustment Mechanism
Wind load (at Rated
N | lbf
Wind Speed: 150 km/h)
Max. Wind Velocity
km/h
mph
Height / Width / Depth mm
inches
Category of
Mounting Hardware
Weight
kg
lb
Packing Size
mm
inches
Scope of Supply
Accessories (order separately if required)
Type No.
Description
Remarks
mm | inches
85010002
85010003
85010008
1 clamp
1 clamp
1 downtilt kit
Mast diameter: 110 – 220 | 4.3 – 8.7
Mast diameter: 210 – 380 | 8.3 – 15.0
Downtilt angle: 0° – 8°
6 x 7-16 female
bottom
3x, Position bottom
continuously adjustable
Frontal:
665 | 149
Maximal:
730 | 164
200
124
2598 / 261 / 146
102.3 / 10.3 / 5.7
H (Heavy)
27.0 / 29.2 (clamps incl.)
59.5 / 64.3 (clamps incl.)
2902 / 284 / 184
114.3 / 11.2 / 7.2
Panel and 2 units of clamps
for 42 – 115 mm |
1.7– 4.5 inches diameter
1)
2)
1) ’ 9 | 0.4
2) 72 | 2.8
Weight approx. Units per
kg | lb
antenna
2.7 | 6.0
4.8 | 10.6
4.3 | 9.5
2
2
1
1.1 | 2.4
2
Mast diameter: 42 – 115 | 1.7 – 4.5
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Material:
Reflector screen: Weather-proof aluminum.
Fiberglass housing: It covers totally the internal antenna components.
Fiberglass material guarantees optimum performance with regards to
stability, stiffness, UV resistance and painting. The color of the radome is
light grey.
All screws and nuts: Stainless steel.
Grounding:
The metal parts of the antenna including the mounting kit are DC
grounded. The inputs 790 – 960 MHz and 1710 – 2180 MHz are also DC
grounded.
2671 | 105.2
1 clamp
2633 | 103.7
936.4880/b ngmn 04.19.01.01 Subject to alteration.
738546
2598 | 102.3
Accessories (included in the scope of supply)
Adjustment mechanism
with integrated scale
All dimensions
in mm | inches
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
80010292V03 Page 3 of 4
6-Port Antenna
Layout of interface:
167 | 6.6 *
145 | 5.7
49 | 1.9
46 | 1.8
108 | 4.3
146 | 5.7 *
35 | 1.4
60 | 2.4
167 | 6.6
184 | 7.2
261 | 10.3 *
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Frequency range
Array
Connector
790 – 960 MHz
1710 – 2180 MHz
1710 – 2180 MHz
R1
B1
B2
1–2
3–4
5–6
B2
B1
R1
Any previous data sheet issues have now become invalid.
Page 4 of 4 80010292V03
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
936.4880/b ngmn 04.19.01.01 Subject to alteration.
Correlation Table
Mounting Hardware
Clamp Included in the Scope of Supply
Suitable for mast diameter
(mm)
[inches]
(mm)
[inches]
Antenna – mast distance
Material of clamp and screws
Weight
(kg)
[lb]
42 – 115
[1.65 – 4.53]
20 – 25
[0.79 – 0.98]
Hot-dip galvanized steel / stainless steel
1.1
[2.43]
100 [3.94]
40 [1.57]
40 [1.57]
72 [2.83]
20–25
[0.79–0.98]
152 [5.98]
15
2–1
’ 4 4.53]
5–
[1.6
M10 ‰MA = 25 Nm
35 [1.38]
M8 ‰MA = 20 Nm
64 [2.52]
125 [4.92]
936.3920/c
Subject to alteration.
20–25
[0.79–0.98]
Please note: Kathrein does not recommend to use counter nuts.
The additional nuts supplied are only meant as spares.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
All dimensions in mm and [inches]
738546 Page 1 of 1
General Instructions
for Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
1
1
2
2
➀ Adjustment wheel with twist-lock
function.
➁ Downtilt spindle with integrated
scale.
➀ Thread for fixing the protective
cap or the RCU (Remote Control
Unit).
➁ Gearwheel for RCU power drive.
To set the downtilt angle exactly,
you must look horizontally at the
scale. The lower edge of the gearwheel must be used for alignment.
Manual adjustment procedure:
0° – max.°
0° – max.°
Remove the protective cap.
Set downtilt angle by rotating the
adjustment wheel.
Screw on the protective cap again.
936.4137
Subject to alteration.
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
General Instructions for Feederline Installation
for Triple-band Antennas
Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To
tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool
(as shown below) in combination with a standard torque-wrench.
Description of bottom end cap (exemplary picture):
7
Ventilation hole
Adjustment mechanism
(protective cap removed)
8
9
Spindle with tilting scale
6
1
2
5
3
4
7-16 female (long neck)
Color coding:
Correlation of each RF input to:
– the corresponding adjustment
mechanism
– the frequency range
– the polarization
There are six feederline connectors and three adjustment mechanisms
located at the bottom of the antenna.
Installation of the feederline connector and RCU (optional):
In order to protect the adjustment mechanism the protective caps have to be attached during
feederline installation!
Kathrein installation set: Type No. 85010005
Set has to be ordered separately!
Set consists of two spanners of 27 and 32 mm width.
Use a torque-wrench to finish
installation (see installation tool).
After feederline installation, the
optional remote control units
(RCU) 7, 8, 9 can be mounted if
required. For a full description
of RCU installation please refer
to the respective data sheet.
27 or 32 mm
These tools are suitable for 7-16 connectors with a wrench
size of 27 or 32 mm.
Tighten nut within a torque range of 25 – 33 Nm depending
on connector manufacturers’ specifications.
Repeat operations as shown for
each feederline!
Page 2 of 2
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]
936.4137
The sequence for installation is:
feederline no. 1, 2, 3, 4, 5, 6.
Carefully put the connector in
place and hand-screw the nut.
Subject to alteration.
1/2ßsquare actuation according to
DIN 3120 Form C