advertisement
Owner’s Manual
EN
C A U T I O N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The above warning is located on the top of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
2
MTX5-D Owner’s Manual
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPOR-
TANT. The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
BROWN
: NEUTRAL
: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or
GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
(3 wires)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Matrix Processor
Model Name : MTX5-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
NEDERLAND / THE NETHERLANDS
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur of gelieve dan contact op te nemen met de vertegenwoordiging van Yamaha in uw land.
• For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative office in your country.
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small chemical waste.
(lithium disposal)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(Perchlorate)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서
사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습
니다.
(class b korea)
MTX5-D Owner’s Manual
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
• Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
• Be sure to connect to an appropriate outlet with a protective grounding connection.
Improper grounding can result in electrical shock.
Do not open
• This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified
Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified
Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
• When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms.
Location
• Do not place the device in an unstable position where it might accidentally fall over.
• Do not block the vents. This device has ventilation holes at the front, side, and rear to prevent the internal temperature from becoming too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire.
• Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.
causing damage to the device(s), malfunction, or even fire.
• Keep device away from the reach of children.
Connections
• Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
Maintenance
• Remove the power plug from the AC outlet when cleaning the device.
Handling caution
• Do not insert your fingers or hands in any gaps or openings on the device (vents).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device (vents). If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified
Yamaha service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors.
• Do not use the device/speakers for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
Backup battery
• This device has a built-in backup battery. When you unplug the power cord from the AC outlet, the internal data is retained. However, if the backup battery fully discharges, this data will be lost. When the backup battery is running low, the [PRESET] display indicates “12.” In this case, immediately save the data to external device such as a computer, then have qualified Yamaha service personnel replace the backup battery.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
4
MTX5-D Owner’s Manual PA_en_1
1/1
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.
Handling and Maintenance
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out.
• When turning on the AC power in your audio system, always turn on the power amplifier LAST, to avoid speaker damage.
When turning the power off, the power amplifier should be turned off FIRST for the same reason.
Saving data
This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off.
The backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.* To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. If the backup battery runs low, alert number “12.” will appear in the [PRESET] display either while the unit is starting up. If this occurs, do not turn off the power, but immediately save the data to a computer or other external storage device, and then have qualified Yamaha service personnel replace the backup battery. The average life of the internal backup battery is approximately five years, depending on operating conditions.
* Data items maintained in the internal memory by the backup battery are as follows:
• Contents of the current preset and the preset number
• Parameters specific to the unit (e.g., configuration data)
• Current parameters for peripheral devices within the same system
• Event log
Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the backup battery fails.
Information
About this manual
• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device.
• Ethernet is a trademark of Xerox Corporation.
• Windows is a registered trademark of Microsoft ® Corporation in the United States and other countries.
• SDHC Logo and SD Logo are trademarks of SD-3C, LLC.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
(weee_eu_en_01)
MTX5-D Owner’s Manual
5
Contents
6
MTX5-D Owner’s Manual
Getting Started
Thank you for purchasing the Yamaha Matrix Processor MTX5-D. This manual will help you take full advantage of the superior functionality offered by the MTX5-D. After you have read the manual, keep it in a safe place for reference when needed.
Included items (please check)
• MTX5-D Owner’s Manual (this document)
• Power cable
• Euroblock plugs (16-pin, 3.50mm pitch) (2)
• Euroblock plugs (3-pin, with tab, 5.08mm pitch) (16)
• Cable ties (16)
Firmware versions
Use MTX Editor to update the firmware of the MTX5-D or check the firmware version. For details on operation, refer to the
MTX Editor User’s Manual.
Download the latest firmware from the “Downloads” page on the following website.
http://www.yamahaproaudio.com/
Precautions for rackmounting
This device is guaranteed to operate at an ambient temperature of 0 to 40 °C. If this device is mounted in an EIA rack together with other devices, heat from the various devices may cause the temperature inside the rack to rise, rendering this device unable to perform to its full potential. To ensure that heat does not accumulate inside this device, please ensure that the following conditions are met when rack-mounting it.
• If you plan to mount this device together with devices that tend to generate heat, such as power amps other than XMV series products, allow 1U or more of vacant space between this device and other devices. Also attach ventilation panels in this space or leave them open to ensure sufficient ventilation.
• Leave the back of the rack open, and allow at least 10 cm of space between the rack and the wall or ceiling to ensure sufficient ventilation. If the back of the rack cannot be left open, provide forced air cooling for the rack, for example by installing a commercially available fan kit. If you install a fan kit, leaving the back of the rack closed may provide more effective cooling. For details, refer to the owner’s manual provided with the rack or fan kit.
MTX5-D Owner’s Manual
7
Introducing the MTX5-D
Features
• A signal processor suitable for small or mid-sized installed systems
The MTX5-D is a signal processor suitable for small or midsized systems such as retail establishments or banquet halls. In addition to a 34 ch. x 16 ch. matrix mixer, it provides 3-band parametric EQ, compressor/gate, auto gain control, eight priority duckers, and eight feedback suppressors. For the output stages, it provides numerous high-performance high-quality processors, such as 4-band parametric EQ, delay, and speaker processor.
• Use Dante to construct small-scale or large-scale systems
Audinate’s “Dante” audio network protocol is used to transfer audio signals over extended distances via Ethernet cable.
MTX Editor makes it easy to specify the audio routing between the MTX5-D and Dante models of the XMV.
• Newly-developed “YDIF” digital audio transmission format
“YDIF” is a digital audio transmission format that uses Ethernet cable to send and receive up to 16 channels of audio and word clock. You can use Ethernet cables up to 30 meters long to easily make connections between devices.
• Slot for installing a Mini-YGDAI card
A separately sold Mini-YGDAI card can be installed to flexibly add analog inputs/outputs or digital inputs/outputs.
• Versatile input/output and SD memory card slot
In addition to eight high-quality monaural mic/line inputs and two stereo line inputs, digital input/output via “YDIF” or
“Dante” allows a maximum total of 30 simultaneous input channels. An SD memory card slot for playback is also provided; allowing MP3/WAV audio files saved on the SD memory card to be played back. In addition to eight channels of analog monaural output, up to 16 channels of digital output can be obtained via “YDIF” or “Dante.”
• Support for external controls
By connecting a “DCP” series dedicated wall-mounted control panel to the [DCP] connector, you can easily control the volume of multiple zones or switch presets. Daisy-chain connection via Ethernet cable allows up to eight “DCP” series control panels to be connected. The total cable length from the
MTX5-D to the farthest control panel can be up to 200 meters, and power is also supplied, allowing you to place the control panel in the ideal location for the room. A NETWORK connector and [GPI] connector are also provided for controlling the unit from an AMX/Crestron or other touch panel device.
• Dedicated “MTX Editor” application software for designing the entire system
“MTX Editor” is application software for editing the parameters of the MTX5-D. Using operating screens that reflect the workflow of designing the installation, this software makes it easy to design a system and make (or adjust) settings. A speaker library of Yamaha-manufactured speakers is also built-in, making it easy to choose settings that will maximize the performance of your speakers.
• iPhone app support
A dedicated iPhone app makes it easy to control the volume and manage presets in the same way as when using the dedicated wall-mounted control panel. You can use your iPhone/ iPod touch to easily control the sound system of a retail location or a banquet hall.
About MTX Editor
MTX Editor is software for the Windows operating system that allows unified construction and control of systems that use the
MTX series.
MTX Editor and the MTX Editor User’s Manual can be downloaded from the following website.
http://www.yamahaproaudio.com/
For details on installing MTX Editor and connecting the
MTX5-D to your computer, refer to the “MTX Setup Manual.”
Using the PDF manual
The MTX Editor User’s Manual is an electronic file in PDF format. You can read this book on a computer. Use Adobe®
Reader® to read this book on screen, search for words very quickly, print specific pages, or click links to display sections of special interest. The ability to search for words, or to follow links directly to relevant sections in the document, are helpful attributes of this electronic file format. We encourage you to take advantage of these benefits.
You can download the latest Adobe Reader application from the website listed below.
http://www.adobe.com/
8
MTX5-D Owner’s Manual
Controls and Connectors
Front Panel
q we t y u i !1 !2
!5
88 r o !0
!4
!3
q SD memory card slot
You can insert an SD memory card here. Music or sound effects can be played back from an SD memory card containing audio files (MP3 files and WAV files). Before you insert an SD memory card into the slot, or remove an SD memory card from the slot, remove the slot cover.
For details on SD memory card handling, refer to page 22.
For details on how to play back audio files, refer to the MTX
Editor User’s Manual.
w [INPUT PEAK] indicators 1–8
These indicators will light red when the input level of the corresponding INPUT channel is -3 dBFS or higher.
e [INPUT SIGNAL] indicators 1–8
These indicators will light green when the input level of the corresponding INPUT channel is -40 dBFS or higher.
r [OUTPUT SIGNAL] indicators 1–8
These indicators will light green when the output level of the corresponding OUTPUT channel is -40 dBFS or higher.
t [PRESET] display
This display usually shows the preset number. It can also show the UNIT ID, alert number, or a message.
y [ s]/[t] buttons
Use these buttons to change the preset number or alert number shown in the above [PRESET] display.
u [ENTER] button
Use this button to confirm the item shown in the above
[PRESET] display.
When an alert number is shown, pressing this button will return to the preset number display.
i [ALERT] indicator
When an alert occurs, the [PRESET] display will indicate the alert number and this indicator will flash red.
o [PRIMARY]/[SECONDARY] indicators
These indicators show the communication status of the
Dante [PRIMARY] and [SECONDARY] connectors.
They flash fast if the Ethernet cables are connected properly.
!0 [SYNC] indicators
This indicator shows the operational status of the Dante network.
If the green indicator lights, the unit is operating as a word clock slave and synching to the word clock.
If the green indicator flashes, the unit is not functioning
properly. In this case, refer to the “Messages” section (see page 26).
If the orange indicator lights or flashes, refer to the “Messages” section.
!1 [POWER] indicator
This indicator will light when this device is powered-on.
!2 [YDIF] indicator
This indicator will light green if the rear panel [YDIF IN]
connector (page 12) is correctly connected to the [YDIF
OUT] connector of another device.
!3 [SCHEDULER] indicator
This indicator will light yellow if an even has been specified
in the scheduler (page 20), and will start flashing one minute
before the event.
!4 [SD/ACT] indicator
This indicator will light yellow if an SD memory card is inserted in the SD memory card slot (q) and has been detected correctly. It will flash while the SD memory card is being accessed.
!5
Power switch
This is the power switch. The power is on if the switch is in the position. The power is off if the switch is in the position.
NOTE
• Do not cycle the power switch in rapid succession. Wait at least 6 seconds before turning the power switch on after it has been turned off. Failing to observe this precaution may cause malfunctions.
• Even when the power switch is turned off, a small amount of current is flowing through the unit. If you plan not to use the unit for a long period of time, remove the power cable from the AC outlet.
MTX5-D Owner’s Manual
9
Controls and Connectors
Rear Panel
q e r t y u i o !0
!1
!2
w !3
NOTE
The MTX5-D has some connectors that are shaped identically but have a completely different function (e.g., [DCP] connector,
Dante [PRIMARY]/[SECONDARY] connectors, [YDIF] connectors). Make the appropriate connections as instructed by the explanation for each connector. Otherwise, you risk damaging your equipment.
q AC IN connector
Use the included power cord to supply power to this connector. First, connect the power cord to this device, and then insert the power cord plug into the AC outlet.
w Ground screw
The supplied power cord has a three-prong plug that will ground the device when plugged into an appropriately grounded three-prong type AC mains outlet. In some cases, you may be able to reduce hum or interference by also connecting this screw to ground.
e Cooling vent
The MTX5-D contains a cooling fan. The cooling air is exhausted here, so please be careful not to block this vent.
r [GPI] connector
This Euroblock connector allows input and output of control signals via GPI (General Purpose Interface).
The MTX5-D provides sixteen ports of analog/digital input, one port of digital input, and eight ports of output. The [IN]-
1–15 terminals detect voltage changes from 0V to 5V. The
[IN]-16 terminal alone supports +24V input; voltages in the range of 2.5–24V are detected as High, and voltages below
2.5V are detected as Low. The [OUT]-1–8 terminals are open collector outputs; they will change between open or closed (Ground). The +5VDC terminals has an output voltage of 5V. Use the included Euroblock plugs to make con-
nections (see “Euroblock plug connection” on page 13 for
details).
For details on connections and usage, refer to “Connecting via the [GPI] connector” on page 21.
CAUTION
Do not input a voltage higher than 5V to the [IN]-1–15 terminals. Doing so may damage your equipment.
!4
t [RS-232C] connector
This 9-pin D-SUB connector allows connection to an RS-
232C compatible controller such as those from AMX or
Crestron.
y [UNIT ID] rotary switch
When multiple devices are connected within the same network, this switch specifies the UNIT ID by which MTX5-D devices are individually distinguished.
DIP switches 1 and 2 described below specify the upper digit, and this rotary switch specifies the lower digit, together allowing you to set the UNIT ID to one of 63 possibilities in the range of 01 to 3F.
NOTE
• Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF and the rotary switch at 0).
• You’ll need to restart the device after changing the setting of the [UNIT ID] rotary switch.
u DIP switches
These switches enable you to specify the settings related to the startup operation of the unit.
NOTE
Set the DIP switches while the power to the unit is turned
OFF. Otherwise, the setting will not be effective.
Refer to the following for details.
Switch Status
Represent a status with switch toggled up.
Represent a status with switch toggled down.
10
MTX5-D Owner’s Manual
Controls and Connectors
Switches 1–2 (UNIT ID)
These switches specify the upper digit and the abovementioned [UNIT ID] rotary switch specifies the lower digit, together allowing you to specify one of 63 different
UNIT ID numbers in a range from 01 to 3F.
Switch position Option
UNIT ID is
“0x”
UNIT ID is
“1x”
UNIT ID is
“2x”
UNIT ID is
“3x”
Functions
The [UNIT ID] rotary switch will have a setting range of
01 through 0F.
The [UNIT ID] rotary switch will have a setting range of
10 through 1F.
The [UNIT ID] rotary switch will have a setting range of
20 through 2F.
The [UNIT ID] rotary switch will have a setting range of
30 through 3F.
NOTE
Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF and the rotary switch at 0).
Switch 3
Not used. Turn it off (up) at any time.
Switch 4 (SECONDARY PORT)
This switch setting determines whether the rear-panel
Dante [SECONDARY] connector will be used for a daisy chain or redundant network.
With the [DAISY CHAIN] setting, you can connect multiple Dante-enabled network devices in a daisy chain
15) for more information about daisy chain connections.
With the Dante [REDUNDANT] setting, the Dante [PRI-
MARY] connector will be used for primary connections, and the Dante [SECONDARY] connector will be used for secondary (backup) connections. If the unit is unable to transmit signals through the Dante [PRIMARY] connector for some reason (e.g., due to damage or accidental removal of the cable, or a failed network switch), the
Dante [SECONDARY] connector will automatically take over communications and functions on the redundant net-
work. Refer to “About redundant networks” in the
“About connections” section (see page 15) for more
information on redundant networks.
Switch position Option
DAISY
CHAIN
REDUNDANT
Functions
The Dante [SECONDARY] connector is used for a daisy chain connection. It can be connected in a daisy chain by connecting to
Dante [PRIMARY] connector of the next device.
The Dante [SECONDARY] connector is used for a redundant network. It will function as backup connection, independent of the network to which the Dante
[PRIMARY] connector is connected.
Switch 5 (PANEL LOCK)
This switch locks the front panel controls. Use this if you want to prevent accidental operation from the front panel.
Switch position Option
UNLOCK
LOCK
Functions
The front panel controls will be available for operation.
The front panel controls will be locked, and will be inoperable. The device can be operated from a computer or an external controller.
Switch 6 (IP SETTING)
This switch specifies how the MTX5-D’s IP address will be specified.
Switch position Option
UNIT ID
PC
Functions
The IP address will be specified according to the
UNIT ID, and will be
192.168.0.(UNIT ID).
The IP address will be determined by the settings of MTX Editor. (See “MTX
Editor User’s Manual.”)
NOTE
You must set this to the “UNIT ID” position the first time you connect this device to a computer after purchase. If you subsequently want to specify the IP address instead of using the UNIT ID, specify the IP address from MTX
Editor and then switch this setting to the “PC” position.
Switches 7–8 (START UP MODE)
These specify whether the MTX5-D will be initialized when it is powered-on.
Switch position Option
RESUME
INIT.
(INITIALIZE)
Functions
This is the normal operating mode. When you power-on the MTX5-D, it will start up in the same state in which it was when the power was turned off.
Initializes the MTX5-D, returning it to the factory-set
i [DCP] connector
Use this connector to daisy-chain separately sold control panels such as the DCP1V4S to control the MTX5-D. Use a
CAT5e or better Ethernet straight cable that has all eight pins connected.
Up to eight control panels can be connected to one MTX5-D.
The total length of the cables from the MTX5-D to the last control panel must not exceed 200 meters.
CAUTION
• Do not connect a control panel to any connector other than the MTX5-D’s [DCP] connector. Since the control panel is not electrically compatible, such connections may cause fire or malfunction.
• Never connect any device to the [DCP] connector other than the separately sold DCP or other control panel. Doing so may damage the other device or this device.
MTX5-D Owner’s Manual
11
Controls and Connectors o [YDIF] connectors
These connectors are used to make a ring connection with the devices that comprise the MTX system, allowing digital audio signals to be transmitted and received. Use CAT5e or better Ethernet STP cables (shielded twisted pair cables) that have all eight pins connected in a straight connection. The maximum cable length between devices is 30 meters, and you can connect up to eight devices that are equipped with the [YDIF] connectors. For details, refer to the MTX Editor
User’s Manual.
NOTE
Using a Mini-YGDAI card for an external word clock may cause noise in system configurations with multiple YDIF connections. In such cases, we recommend using a different word clock source, such as Dante or YDIF.
!0 POWER IN +24V DC
Support for this connector is planned for the future.
!1 Dante [PRIMARY]/[SECONDARY] connectors
This is an RJ45 connector used to connect the unit to a computer or a Dante device such as the XMV4280-D via an
Ethernet cable (CAT5e or better is recommended).
If DIP switch 4 on the front panel is set upward (to DAISY
CHAIN), audio signals coming into one of these connectors
more information on daisy chain connections.
If DIP switch 4 on the front panel is set downward (to
REDUNDANT), the Dante [PRIMARY] connector will be used for primary connection, and the Dante [SECONDARY] connector will be used for secondary (backup) connection. If the unit is unable to transmit signals through the Dante [PRI-
MARY] connector for some reason (e.g., due to damage or accidental removal of the cable, or a failed network switch), the Dante [SECONDARY] connector will automatically take
information on redundant networks.
The connected computer is used mainly with the dedicated
“MTX Editor” application program for the purpose of setting up or controlling the MTX system.
NOTE
• Since Dante-compatible equipment made by Yamaha such as the MTX5-D contains a built-in network switch, the number of hops will be two or more. For this reason, the 0.15 msec Latency setting in Dante Controller will be grayed-out and unavailable.
• Use STP (shielded twisted pair) cable to prevent electromagnetic interference.
!2 [ST IN] connectors
These are unbalanced RCA phono jacks for inputting analog audio signals from a CD player or other device.
!3 Slot
This slot allows a separately sold Mini-YGDAI I/O card to be installed.
!4 [INPUT]/[OUTPUT] connectors
These are balanced input/output connectors for analog audio input and output. Connect line level devices or microphones to the [INPUT] connectors, and line level devices to the
[OUTPUT] connectors. The [INPUT] connectors provide head amps, and can also provide +48V phantom power.
MTX Editor is used to specify the gain of the internal head amps and to turn the phantom power on/off.
Use the included Euroblock plugs to make connections (see
“Euroblock plug connection” on page 13 for details).
NOTE
Adjusting the internal head amp gain between +17 dB and
+18 dB will internally turn PAD on/off. Noise may occur if there is an impedance difference between the Hot and Cold of a device connected to the [INPUT] connectors while phantom power is being used.
12
MTX5-D Owner’s Manual
Controls and Connectors
Euroblock plug connection
Use the included Euroblock plugs when making connections to the [INPUT]/[OUTPUT] connectors and [GPI] connector.
Cable preparation
approx. 7 mm
(approx. 5 mm for the GPI connector) approx. 20 mm
• Use stranded wire for Euroblock connections, and strip the wire as shown in the illustration. With a
Euroblock connection, the stranded wire may be prone to breakage because of metal fatigue due to the weight of the cable or due to vibration. Cables connected to the [INPUT]/[OUTPUT] connectors should be fastened to the tab of the Euroblock plug
(3-pin) using the included cable ties (see illustration at right). When rack-mounting the device, use a lacing bar when possible to bundle and secure the cable.
NOTE
Do not tin (plate with solder) the stranded wire.
• If cables will be frequently connected and disconnected, as in the case of a portable system, we recommend that you use ferrules with insulation sleeves. Use a ferrule whose conductor portion has an external diameter of 1.6 mm or less (1.3 mm or less for the [GPI] connector) and a length of approximately 7 mm (approximately 5 mm for the [GPI] connector) such as the AI 0,5 - 6 WH made by the
Phoenix Contact corporation.
approx. 7 mm
(approx. 5 mm for the GPI connector)
1.6 mm or less
(1.3 mm for the GPI connector)
1. Loosen the terminal screws.
Loosen
Slotted screwdriver
Terminal screw
Euroblock plug
Tab
* The explanation uses tabbed Euroblock plugs.
NOTE
Use a slotted screwdriver with a blade width of 2 mm or less for the [GPI] connector’s Euroblock plug (16-pin), and a blade width of 3 mm or less for the [INPUT]/[OUT-
PUT] connector’s Euroblock plug (3-pin).
3 mm or less
2. Insert cables.
+ –
G
3. Securely tighten the terminal screws.
Pull the cables (not too strongly) to confirm that they are securely connected.
4. For the Euroblock plugs (3-pin) of the
[INPUT]/[OUTPUT] connectors, use the included cable ties to fasten the cable to the tab.
NOTE
Trim off the extra portion of the cable tie as necessary.
MTX5-D Owner’s Manual
13
Controls and Connectors
5. Plug the Euroblock plug into the [GPI] connector or [INPUT]/[OUTPUT] connector of the MTX5-D.
3. Align the edges of the card with the guide rails inside the slot, and insert the card into the slot.
Push the card all the way into the slot so that the connector at the end of the card is correctly inserted into the connector inside the slot.
NOTE
When connecting unbalanced cables to the [INPUT] connector, use a jumper wire to connect the “-” and “G” of the Euroblock.
+ –
G
Installing an option card
Before you install I/O cards in slots, you must check the
Yamaha website to determine whether the card is compatible with the MTX5-D.
http://www.yamahaproaudio.com/
To install an optional Mini-YGDAI card, proceed as follows.
1. Make sure that the power is turned off.
2. Loosen the screws that hold the slot cover in place, and remove the slot cover.
Keep the removed slot cover and screws in a safe place.
Card
NOTICE
When inserting the card, align both sides of the card with the guide rails in the slot of the host device.
4. Use the screws included with the card to fasten the card in place.
Malfunctions or incorrect operation may occur if the card is not fastened.
CAUTION
Before connecting a separately sold Mini-YGDAI I/O card to the MTX5-D, you must turn off the power switches for the MTX5-D. Failure to observe this will cause malfunction or electric shock.
Slot cover
14
MTX5-D Owner’s Manual
About Dante
This product features Dante technology as a protocol to transmit audio signals. Dante is a network protocol developed by Audinate. It is designed to deliver multi-channel audio signals at various sampling and bit rates, as well as device control signals over a Giga-bit Ethernet (GbE) network. Dante also offers the following benefits:
• It transmits up to 512 in/512 out, for a total 1024 channels (in theory) of audio over a GbE network. (The MTX5-D features 16 in/16 out with a 24/32-bit resolution.)
• Dante uses high accuracy network synchronization standards to achieve sample-accurate playback with extremely low latency and jitter. Four types of latency are offered by the MTX5-D: 0.25 msec, 0.5 msec, 1.0 msec, and 5.0 msec.
• Dante supports resilient redundant connections against unexpected network problems via primary and secondary circuits.
Visit the Audinate website for more details on Dante.
http://www.audinate.com/
Additional information on Dante is also posted on the Yamaha Pro Audio website:
http://www.yamahaproaudio.com/
About connections
There are two ways to connect the MTX5-D to a Dante network.
NOTE
Please do not use the EEE function (*) of network switches in a
Dante network.
Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
Therefore we strongly recommend that:
• If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
• If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
* EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
Daisy chain network
A daisy chain is a wiring scheme in which multiple devices are connected together in sequence. In this way, networking is simple and requires no network switches.
This connection method is suitable for a simple system with a small number of devices.
However, if a large number of devices are connected, the latency value must be increased. Also, if a connection is broken in a daisy chain network, the signal flow is interrupted at that point and no signal will be transferred beyond that point.
NOTE
The computer that’s running MTX Editor must be connected to the unused Dante [PRIMARY] connector or Dante [SEC-
ONDARY] connector on the MTX5-D. For details on connections, refer to “MTX Setup Manual.”
MTX5-D (ID#1)
MTX5-D (ID#2)
MTX5-D (ID#3)
88
88
88
Computer
PRIMARY
SECONDARY
PRIMARY
SECONDARY
PRIMARY
Star network
In a star network, each device is connected to a central hub.
Using a GbE-compatible network switch enables you to configure a wide-band, large-scale network. We recommend a network switch that features various functions to control and monitor the network (such as Qos, the ability to assign priority to data flows — e.g., clock synchronization or audio transmission on certain data circuits.)
With this topology, it is common to configure a redundant network so that an unexpected network problem will not affect any audio or otherwise stable communications.
MTX5-D Owner’s Manual
15
About Dante
About redundant networks
A redundant network consists of two circuits, a primary circuit and a secondary circuit. Normally, the network operates on the primary circuit. However, if the primary connection is broken, the secondary circuit will automatically take over communications. Therefore, using a redundant network with a star topology would increase resiliency against unexpected network problems relative to a daisy chain network.
NOTE
The computer that’s running MTX Editor must be connected to the [PRIMARY] connector of the MTX5-D. For details on connections, refer to “MTX Setup Manual.”
About Dante Controller
Dante Controller is a software application that allows configuration and audio routing of Dante networks. Use Dante
Controller if you need to make connections and settings for devices not supported by MTX Editor, or if you need to specify complex signal routings on the Dante network.
More information is posted on the following website.
http://www.yamahaproaudio.com/
To run Dante Controller, a computer must feature a GbEcompatible Ethernet connector.
Refer to the Dante Controller owner’s manual for details on
Dante Controller.
Computer
Network switch A
MTX5-D (ID#1)
88
Network switch B
MTX5-D (ID#2)
88
MTX5-D (ID#3)
88
Primary Dante
Secondary Dante
16
MTX5-D Owner’s Manual
Quick Guide
This section explains basic settings and connection procedures for constructing an MTX system using the MTX5-D. Some of the steps may not be necessary for your system; if so, proceed to the next step.
Preparations
Use MTX Editor to make the required settings before you actually install and connect the equipment.
1. Prepare a computer in which to install MTX
Editor.
2. Install MTX Editor in your computer.
For details on installation, refer to “MTX Setup Manual.”
NOTE
Use MTX Editor V1.1 or later if you’re setting up an MTX system that uses the MTX5-D.
3. Specify the IP address and subnet mask of your computer.
Enter “192.168.0.253” as the IP address and
“255.255.255.0” as the subnet mask.
4. If you want to play back music or other audio files from the MTX5-D itself, prepare an SD memory card.
Copy the audio files to your SD memory card. For details on
5. Start up MTX Editor.
For details on installing and using MTX Editor, refer to
“MTX Setup Manual” and “MTX Editor User’s Manual.”
6. Set up the entire MTX system as directed by the wizard.
Make settings such as the number of connected MTX/XMV/
Exi8/EXo8/DCP devices, and the UNIT ID and YDIF mode
(Cascade mode or Distribution mode) for each device. For
details on YDIF, refer to “Features” (page 8), and “o
[YDIF] connectors” in “Controls and Connectors” (page 12).
Print out the schematic diagram shown at the end of the wizard, and use it when you make the actual connections and settings.
7. The audio signal flow in the MTX5-D and the principal parameters to be set are as follows.
Make the settings in the order shown.
For details on each item, refer to “MTX Editor User’s Manual.”
Input port settings (e.g., HA gain, +48V on/off)
Input patching
Input channel settings (e.g., gain, HPF, EQ)
Matrix
Matrix/zone settings
Router
Output channel settings (e.g., output level, delay/ room EQ, speaker processor)
Output patching
Output port settings (e.g., polarity, output gain)
Make settings for the necessary components while offline.
• HA section:
HA gain, +48V (phantom power)
• Input channel section:
HPF, 3BAND EQ, GATE, COMP, FBS, AGC, Level
• Matrix/Zone section:
Two-level priority ducker, ANC
• Output channel section:
Room EQ (Delay, 4Band EQ), SPEAKER PROCES-
SOR (X-over, Delay, 6Band EQ, Level, Limiter)
MTX5-D Owner’s Manual
17
Quick Guide
8. Make DCP settings.
Assign the parameters of the MTX5-D to the switches and knobs of the connected DCP units. Here you can also specify the brightness of the DCP’s LEDs. For details on how to make DCP settings, refer to “MTX Editor User’s Manual.”
9. As necessary, make settings for devices other than the MTX5-D.
For details, refer to “MTX Setup Manual.”
10. Specify and store a preset.
You can use presets to change the volume of zones and the audio source to play (e.g., SD memory card or CD player) in a single action. To prevent problems such as a sudden increase in volume when the MTX5-D is operated, we recommend that you store the preset with the output level lowered to “-infinity (
∞
).” For details on presets and how to
recall them, refer to “Recalling (switching) presets” on page 20, and “MTX Editor User’s Manual.”
11. Save your settings and close MTX Editor.
A project file with the extension “.mtx” will be created.
On-site work (Installation and wiring)
Install and connect the system while referring to the schematic diagram you printed out.
1. Install the MTX5-D, and make the analog audio connections.
2. Make digital connections between the MTX5-D and any XMV/EXi8/EXo8.
Make a ring connection with the devices equipped with a
[YDIF] connector.
3. Connect the MTX5-D and the Dante device that supports the MTX5-D to the Dante network.
For details on connections, refer to “About connections” on page 15.
4. Connect the MTX5-D to an analog input amp.
5. Set the UNIT ID of the MTX5-D and the XMV/
EXi8/EXo8.
Set the UNIT ID for every MTX5-D and XMV/EXi8/EXo8 device you connected in the above steps. The UNIT ID is specified by the combination of the [UNIT ID] rotary switch and DIP switches located on each device’s rear panel. Set each device to a different UNIT ID so that no conflict occurs.
6. Make connections between the MTX5-D and the DCP units.
Daisy-chain the DCP units. Set the panel ID and termination settings of the DCP units. For details, refer to the DCP owner’s manual.
18
MTX5-D Owner’s Manual
Quick Guide
On-site work (Settings in MTX Editor)
Use MTX Editor to make adjustments for the entire system.
1. Connect the computer to the MTX5-D/XMV/
EXi8/EXo8 via a network switch.
If you’re using only the MTX5-D, you can connect it directly to the computer.
2. Start up MTX Editor and load the project file that you previously created.
3. Power-on the MTX5-D.
4. Power-on the XMV/EXi8/EXo8 and the analog input amps.
5. In the [To Device] direction, place the MTX5-
D/XMV/EXi8/EXo8 and MTX Editor online (in a synchronized state).
“Online” refers to the state in which the MTX5-D itself is connected with MTX Editor and is synchronized. When the devices are online, MTX Editor can be used to control the
MTX5-D/XMV/EXi8/EXo8. For details on how to put the device online, refer to “MTX Editor User’s Manual.”
6. Check the presets.
Recall a preset, and verify that the settings are correct.
For details on presets and how to recall them, refer to
“Recalling (switching) presets” on page 20.
7. Check the signal processing.
Input audio signals into the MTX5-D, and check the meters in MTX Editor to verify that the volume and routing are set correctly.
8. Adjust the output level of the MTX5-D and the output level of the amps so that the audio is output from the speakers at an appropriate level.
One by one, turn on each output channel and adjust its output level.
9. Store the preset.
Recall, edit, and save other presets in the same way.
10. Save your settings and close MTX Editor.
A project file with the extension “.mtx” will be created.
NOTE
The settings you make while online are saved in the
MTX5-D itself, but we recommend that you use MTX Editor to save them as a project file for future maintenance and readjustments.
MTX5-D Owner’s Manual
19
Various Procedures
Recalling (switching) presets
With the MTX system, input/output port patching, matrix mixer settings, and the parameters of XMV amps within the same
MTX system are stored together as a “preset” in the MTX5-D and in MTX Editor for recall when desired.
Each MTX system can store 50 presets. MTX Editor is used to edit presets.
Each preset contains settings such as the following.
• Input/output port settings and patching
• Input/output channel gain and EQ settings
• Matrix mixer settings
• Zone settings
• Routing settings
• Effect settings
• DCA and mute group settings
• Parameter settings for XMV devices within the same MTX system
• Preset name
For details, refer to “MTX Editor User’s Manual.”
Switching presets from the MTX5-D
1. While watching the [PRESET] display, use the [
s]/[t] buttons to select the preset
number that you want to recall.
The [PRESET] display will flash during this time.
2. Press the [ENTER] button to confirm your selection.
The [PRESET] display will stop flashing; the preset has been recalled.
NOTE
• If you leave the device for 30 seconds with the [PRE-
SET] display flashing, it will revert to the previous preset number.
• If a control panel such as a DCP series unit is connected, you’ll be able to easily switch presets.
Setting the clock
Each time the devices connected to the MTX system are brought online, the date and time of the computer will be transmitted to all devices, automatically updating their internal clocks.
You can also update the date and time settings on all devices connected to the same network by transmitting the computer’s date and time settings from the “Clock” dialog box in MTX
Editor.
For more information on operation, refer to “MTX Editor
User’s Manual.”
Using the scheduler
The scheduler can switch presets or play music and sound effects from the SD memory card at the date and time you specify. Each such setting is called an “event.”
Event settings are made in the “Scheduler” dialog box of MTX
Editor. For details on operation, refer to “MTX Editor User’s
Manual.”
< Example 1 >
Switching background music and playback area according to the time of day
In commercial facilities that switch background music and playback areas at different times of the day, you can switch the type of music and the playback area according to the time of day.
9:00 12:00 14:00 18:00 22:00
Indoors
Outdoors
Energetic music
Refreshing music
No music
Calm music
Atmospheric music
No music
< Example 2 >
Switching the playback time according to the day of the week
In commercial facilities that switch the time period of music depending on the day of the week, you can specify the music pattern and playback times according to the day of the week and the hours of operation.
• Monday–Friday
10:00 20:00
Music pattern 1
• Saturday
10:00 22:00
Music pattern 2
• Sunday
12:00 20:00
Music pattern 3
You can also play seasonal music, or specify exceptions such as stopping playback on days when the facility is not operating.
20
MTX5-D Owner’s Manual
Various Procedures
Connecting via the [GPI] connector
GPI (General Purpose Interface) devices can be connected to the rear-panel [GPI] connectors. GPI allows a variety of control signals to be exchanged with external controllers or other devices.
• Connection examples using the [GPI IN] connector
Example: Controlling the MTX5-D from a switch box
MTX5-D
+5VDC
+V
IN
CPU A/D
100k
The MTX5-D provides 16 input ports and 8 output ports.
• The +5VDC terminals have an output voltage of 5V. The maximum current draw is 100 mA total for the two terminals. If you are using a switch/variable resistor and an LED/ relay simultaneously, connect one terminal to the switch/ variable resistor and the other terminal to the LED/relay.
• The [IN]-1–15 terminals detect voltage changes from 0V to
5V. The [IN]-16 terminal alone supports +24V input; voltages in the range of 2.5–24V are detected as High, and voltages below 2.5V are detected as Low.
• The [OUT]-1–8 terminals are open collector outputs; they will change between open or closed (Ground). The maximum voltage that can be applied is +12V. The maximum current draw is 75 mA per port.
The GPI controller parameters are assigned via the MTX Editor application.
Euroblock plugs (16-pin) are used for connections to the [GPI]
connector. For details, refer to “Euroblock plug connection” on page 13.
NOTE
By making input/output channel settings in MTX Editor, you can recall presets or edit parameters on an external GPI device or send signals to it. For details, refer to the “MTX Editor User’s
Manual.”
Example: Controlling the MTX5-D with a 10k ohm linear taper potentiometer.
MTX5-D
+5VDC
CPU A/D
100k
+V
IN
GND
Variable resistor
• Connection examples using the [GPI OUT] connector
Example: Lighting LED indicators on external devices from the MTX5-D
MTX5-D
+5VDC
10
+V
OUT
CPU Max. 75mA
CAUTION
Do not exceed 75 mA of current from the OUT connector.
Example: Lighting an LED by switching an external device’s relay from the MTX5-D
MTX5-D
+5VDC +
10
+V
OUT
CPU
–
Max. 75mA
NOTE
For the method of adjusting the detection range of the input voltage at the [GPI] connector (calibration), refer to the “MTX
Editor User’s Manual.”
MTX5-D Owner’s Manual
21
Various Procedures
Using the MTX5-D to play audio files saved on an SD memory card
The MTX5-D can use commercially available SD memory cards to play back audio files such as music and sound effects without needing to connect a CD player or other audio device.
The MTX5-D can play back audio files in either MP3 or WAV formats.
Here we explain how to handle SD memory cards. In order to play back audio files saved on an SD memory card, you must make settings in MTX Editor. For details, refer to “MTX Editor
User’s Manual.”
NOTE
Use an SD format or SDHC format memory card (SDXC format is not supported). However, depending on the manufacturer or type of memory card, some memory cards might not work correctly with the MTX5-D.
Inserting an SD memory card
1. Use a 2.5 mm hex key to open the cover of the SD memory card slot.
2. With the terminals of the SD memory card facing downward, insert the card straight into the slot until it clicks into place.
Initializing the MTX5-D
Here’s how to initialize the MTX5-D’s internal memory, restoring it to the factory settings.
1. Power-off the MTX5-D.
2. Set the rear panel DIP switches 7 and 8 to the
“INIT. (INITIALIZE)” position.
3. Power-on the MTX5-D.
Initialization will start.
The status of execution is shown by the front panel [ALERT] indicator, the [PRIMARY] through [SYNC] indicators, and the [YDIF] through [SD/ACT] indicators.
• During initialization:
All indicators other than [ALERT] will flash.
• Initialization completed:
Only the green indicators will flash.
When the SD memory card has been correctly recog-
nized, the [SD/ACT] indicator (page 9) will light. The
[SD/ACT] indicator will flash while the card is being accessed.
NOTE
To prevent theft of the SD memory card, we recommend that you leave the cover installed during use.
Removing the SD memory card
1. Gently press the SD memory card inward.
The card will pop out slightly; gently pull it completely out.
• Initialization failed:
The [ALERT] indicator will flash.
CAUTION
Do not turn off the power to the MTX5-D during initialization. Otherwise, a malfunction may occur.
NOTE
If initialization failed, contact Yamaha representatives / authorized distributors to have the device inspected. A list of
Yamaha representatives / authorized distributors appears near the end of this manual.
22
MTX5-D Owner’s Manual
4. When initialization is completed, power-off the
MTX5-D once again.
5. Set the rear panel DIP switches 7 and 8 to the
“RESUME” position.
6. Power-on the MTX5-D again.
The MTX5-D will start up in its factory-set state.
Various Procedures
MTX5-D Owner’s Manual
23
Appendix
Troubleshooting
The Yamaha Pro Audio website provides a FAQ (a list of frequently asked questions, with answers).
http://www.yamahaproaudio.com/
Symptom
The device does not turn on, or the panel LEDs do not light up.
Can’t exchange data between the
MTX5-D and MTX Editor (MTX5-
D is not shown in MTX Editor).
No audio input is present.
No audio is output.
The panel controls don’t work.
Possible cause, and action
Connect the power cord properly.
Make sure that the power switch is turned on.
If the power still does not turn on, contact your Yamaha dealer.
Is the Dante connector of the MTX5-D correctly connected to the computer?
Have you specified the correct UNIT ID using the [UNIT ID] rotary switch and DIP switches 1 and 2 on the rear panel? Could the UNIT ID be conflicting with another device?
Set the rear panel DIP switch 6 (IP SETTING) to “UNIT ID” so that the IP address will be automatically assigned according to the UNIT ID.
Connect the cable properly.
Make sure that a signal from an external device is being input.
Set the gain of the internal head amplifier or external head amplifier to an appropriate level.
In the “EXT. I/O” screen of MTX Editor, check whether the audio routing between devices is set correctly.
Is the optional I/O card installed correctly?
In the “Word Clock” dialog box of MTX Editor, is the word clock set correctly?
Could the output level be lowered?
In MTX Editor, could the channel’s ON button be turned off?
Is the signal routing specified correctly?
Have the other settings in MTX Editor been made correctly?
Is the optional I/O card installed correctly?
Could rear panel DIP switch 5 (PANEL LOCK) be set to “LOCK”? Change this to “UNLOCK” to defeat the panel lock function. If you are still unable to operate the device, contact your Yamaha dealer.
Can’t operate the DCP.
The DCP’s LEDs are dim.
[YDIF] indicator does not light.
Can’t play audio files from the SD memory card.
SD memory card is not detected.
Are you using an appropriate cable, and is the MTX5-D correctly connected to the DCP?
Did you power-cycle the MTX5-D after connecting the DCP? The DCP will be detected when the power is turned on.
Did you assign the DCP’s ID and parameters correctly in MTX Editor? Also, did you specify a DCP library item in the “Preset” dialog box as the preset to be recalled?
Is termination turned on for the last-connected DCP?
Could nine or more DCP units be connected? A maximum of eight DCP units can be connected to one MTX5-D.
Could the total cable length from the MTX5-D to the last control panel be exceeding 200 meters?
In the “Preset” dialog box of MTX Editor, have you specified the DCP library that you created? Also, did you execute a preset recall after specifying this? The settings of the “Preset” dialog box will not be applied until you execute a preset recall.
Did you set the DCP’s LED brightness appropriately in MTX Editor?
Did you use an appropriate cable to make proper YDIF connections between the MTX5-D and other devices in the MTX system? Also, is the power to the YDIF-connected devices turned on?
Is the SD memory card recognized correctly? Make sure that the front panel [SD/ACT] indicator is lit or flashing.
In MTX Editor, have you made the correct settings for SD memory card playback and for the scheduler?
Are playable audio files saved in the specified folder?
Are you using an SD memory card type and format that is supported? Refer to the “Specifications”
page, and use a supported card.
Is the SD memory card inserted correctly? Turn off the power of the MTX5-D, re-insert the card, and then turn the power on again. If the [SD/ACT] indicator does not light and the card is not detected, it may be that the card is damaged.
24
MTX5-D Owner’s Manual
Appendix
Symptom
Preset does not switch at the time specified by the scheduler.
The [ALERT] indicator is flashing.
Can’t switch presets from a device connected to the [GPI] connector.
Possible cause, and action
The MTX5-D’s clock is set by sending clock data from the computer via MTX Editor to the MTX5-D.
Make sure that the computer’s clock is set correctly.
Have you made the correct scheduler settings in MTX Editor? If the [SCHEDULER] indicator is not lit or flashing, it may be that settings were not made correctly in MTX Editor.
An error has occurred. The alert number is shown in the front panel [PRESET] display; refer to
“Alert list” on page 27 to determine the content of the error and take the appropriate action.
Is the GPI device connected correctly?
Have the correct GPI-related settings been made in MTX Editor?
Volume becomes unstable when it is operated from a device connected to the [GPI] connector.
Settings of the [UNIT ID] rotary switch or DIP switch are not applied.
Route the wiring to avoid picking up noise; for example, replace the cable with a shielded or shorter cable.
Turn off the power before you change the setting.
MTX5-D Owner’s Manual
25
Appendix
Messages
Warnings and certain other types of information are displayed via the MTX5-D front panel indicators.
Messages are also displayed in the Dante Controller Error Status field.
Each indicator lights or flashes as described below:
Unlit
Lit
Flash
Flash x 2
The indicator is off.
The indicator remains lit steadily.
The indicator continues to flash.
The indicator flashes twice cyclically.
Information Messages
The status is shown by the lit/flashing state of the indicator.
If the orange [SYNC] indicator is unlit, the unit is operating normally.
If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.
SYNC Indicators Description
(green) Unlit
(orange) Lit
(green) Flash
(orange) Unlit
Synchronization is occurring.
Explanation
Please wait until the unit synchronizes completely. It may take approximately
60 seconds for synchronization to be completed.
The unit is functioning correctly as the word clock master.
The unit is operating as the word clock master.
(green) Lit
(orange) Unlit
The unit is functioning correctly as the word clock slave.
The unit is operating as the clock slave and the clock is synchronized.
Warning Messages
The indicator will remain lit or continue flashing cyclically until the problem is solved.
If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.
SYNC Indicators Description
(green) Unlit
(orange) Flash
The word clock is not set correctly.
Possible Solution
Set the clock master and sampling frequency correctly on the MTX Editor or in Dante Controller.
(green) Unlit
(orange) Flash x2
Dante Network circuit is broken.
Make sure that the Ethernet cables are not removed or short-circuited.
If the green indicator is flashing, the unit is the clock master.
If the green indicator is lit, the unit is the clock slave and the clock is synchronized.
SYNC Indicators Description
(green) Lit or flash
(orange) Lit
A non-GbE-compatible device is connected.
(green) Lit or flash
(orange) Flash
(green) Lit or flash
(orange) Flash x 2
Possible Solution
When transferring audio via Dante, use device that supports GbE.
The Dante [SECONDARY] connector has taken over communications during redundant network operation.
Check the circuit connected to the
Dante [PRIMARY] connector.
An abnormality has occurred on the circuit connected to the Dante [SECONDARY] connector during redundant network operation.
Check the circuit connected to the
Dante [SECONDARY] connector.
26
MTX5-D Owner’s Manual
Appendix
Alert list
This is a list of the alerts that may be indicated in the front panel [PRESET] display.
Alert number
Meaning Response
01–09
10
11
12
13
The device has not started up correctly.
The internal backup battery has been completely exhausted or is not installed.
The internal backup battery has run extremely low, and it is possible that the internal memory has been cleared.
Turn the power off, then turn on after waiting at least 6 seconds. If this does not solve the problem, please initialize the memory. Should this also fails, contact your
Yamaha dealer.
When you turn off the power, the current settings will be lost, and will return to the default values. Please stop use immediately, and contact your Yamaha dealer.
When you turn off the power, the current settings will be lost, and will return to the default values. Please stop use immediately, and contact your Yamaha dealer.
The internal backup battery has only a small amount of power remaining.
This does not affect the operation of the device. However, if you continue using the device, the settings may be lost and reset to the default values. Contact your
Yamaha dealer as soon as possible.
A problem has occurred with the internal clock, and it has been initialized (January
1, 2000, 0:00).
If this occurs each time you turn on the power, it is possible that the internal backup battery has run down or that the device has malfunctioned. Contact your
Yamaha dealer.
If this occurs only once, an abnormality was detected with the clock setting and it was initialized; use MTX Editor to set the time.
14
15
20
21
22
23
24
25
26
27
28
30
40
41
42
43
50
The current preset saved in internal memory has been lost.
Recall the preset. If this does not solve the problem, contact your Yamaha dealer.
The settings saved in internal memory have been lost.
An unsupported Mini-YGDAI card is inserted in the slot, or the inserted Mini-
YGDAI card has malfunctioned.
The word clock master has become unlocked.
Either the internal backup battery has run low, or the device has malfunctioned.
Contact your Yamaha dealer.
Replace the card with a supported Mini-YGDAI card or check that the supported
Mini-YGDAI card is working correctly in another Host.
Make sure that the word clock signal is being input correctly.
The digital signal being input to the [YDIF
IN] connector is not synchronized to the word clock of this device.
Make sure that YDIF cables are properly connected.
Use cables that meet the required specifications.
The digital signal being input to the [YDIF
IN] connector is not continuously synchronized to the word clock of this device.
The digital signal being input to the slot is not synchronized to the word clock of this device.
Either input a signal that is synchronized, or specify the slot as the word clock master.
The digital signal being input to the slot is not continuously synchronized to the word clock of this device.
The digital signal being input to the Dante connector is not synchronized to the word clock of this device.
Either input a signal that is synchronized, or specify the Dante as the word clock master.
The digital signal being input to the Dante connector is not continuously synchronized to the word clock of this device.
The Dante sampling frequency has been changed to match the word clock master of this unit.
Check the word clock setting of this unit. Then set the sampling frequency of the
Dante network.
There is a problem with the connection of the [YDIF IN] connector.
Make sure that YDIF cables are properly connected.
Use cables that meet the required specifications.
Duplicate IP addresses.
Change the IP addresses so that there are no duplicates.
IP address was not set within 60 seconds of startup.
Please check rear panel DIP switch 6 (IP Setting). If DIP switch 6 is set to “PC,” use MTX Editor or DHCP server to specify the device IP address.
A device within the MTX system was not found on the network.
Too many devices are connected to the network.
The UNIT ID is set to “00.”
Power-on all devices in the system, and make sure that they are correctly connected to the network.
Reduce the number of devices connected to the network.
Set the UNIT ID to something other than “00.”
MTX5-D Owner’s Manual
27
Appendix
Alert number
51
52
53
56
58
60
61
64
70
71
Meaning Response
Devices with identical UNIT IDs were found connected within the same network.
Change the UNIT ID so that there are no duplicates.
A communication error occurred with the
[DCP] connection.
• If an error was shown in the DCP panel, refer to the DCP owner’s manual and take the appropriate action.
• Ensure that the panel ID of the DCP units do not conflict.
• Verify that the cables are correctly connected and are within the specified length.
The DCP connected to the [DCP] connector has been configured differently from the project settings.
• Check that the required DCP is connected.
• Check whether a different model of DCP might be connected.
SD memory card was not recognized.
Unable to play the specified file or folder in the SD player.
Use an SD memory card that complies with the specifications. (See page 29.)
Verify that the specified audio file or folder exists in the SD memory card. There must be at least one playable audio file in the specified folder.
A preset recall attempt has failed.
The preset could not be recalled.
Initialize the memory of the device. If this does not solve the problem, contact your
Yamaha dealer.
The recall could not be executed because the preset to be recalled when the MTX starts up was not found.
Specify a preset that exists. No sound will be output unless an appropriate preset is recalled.
• The Preset selected for recall cannot be recalled as no data has been stored to it.
• Another device may have been added after presets were stored. Please synchronize and check all presets using MTX Editor, edit as necessary and store again.
Synchronization has not been completed. It may be that synchronization was halted before completion.
Perform synchronization again using MTX Editor. If this does not solve the problem, initialize the memory of the device and synchronize again. If this also fails, contact your Yamaha dealer.
The UNIT ID settings when synchronization was performed do not match the current UNIT ID settings.
Do not change any UNIT ID’s after performing synchronization. If you’ve changed any UNIT ID’s, perform synchronization again.
28
MTX5-D Owner’s Manual
Appendix
Specifications
Product specifications
Dimensions (W x H x D)
Weight
Power supply voltage
480(W) x 88(H) x 351(D)mm, 2U
6.3kg
Japan: 100V 50/60Hz
US/Canada: 110V–240V 50/60Hz
Others: 100V–240V 50/60Hz
Power consumption
Heat dissipation (per hour)
65W max.
55.9kcal max.
Operating temperature range 0 °C–40 °C
Storage temperature range
NC value
Number of memories
Maximum number of simultaneously usable devices
Power cord length
Included items
Separately sold options
-20 °C–60 °C
23 (1m from the front panel)
Preset memories: 50
Four MTX devices (However in a system in which one to four MTX devices are connected, a total of up to 20 devices including devices such as the EXi8, EXo8, XMV can be connected.)
2.5m
Power cord, Euroblock plugs (3-pin, tabbed) x 16, Euroblock plugs (16-pin) x 2, cable ties x 16, owner’s manual
DCP1V4S-US/EU, DCP4S-US/EU, DCP4V4S-US/EU digital control panels
Electrical specifications
Sampling frequency
Signal delay
Frequency response
Total harmonic distortion
48kHz/44.1kHz
Less than 3.0ms (AD-DA @48kHz)
20Hz to 20kHz, -1.5dB min, 0dB typ., +0.5dB max.
Less than 0.05% (+4dBu, Gain:-6dB); less than 0.1% (+4dBu, Gain:+66dB)
Dynamic range
Equivalent input noise (EIN)
107dB (Gain:-6dB)
-126dBu (Gain: +66dB)
Crosstalk / Channel separation -100dB (@1kHz)
Maximum cable length
Indicators
[YDIF] connector: 30 meters (Cable length between devices)
[DCP] connector: 200 meters (total cable length from the MTX5-D to the last DCP)
INPUT PEAK: RED -3dBFS
INPUT SIGNAL: GREEN -40dBFS
OUTPUT SIGNAL: GREEN -40dBFS
Phantom power 48V (per channel; individually settable)
Connector specifications
Format
Cable specifications
[GPI] connector: IN (1–15ch): 0–5V
IN (16ch): 2.5–24V : High, 2.5V or less: Low, Allowable input +24V
OUT: Open collector
+V: DC5V
Dante [PRIMARY]/[SECONDARY] connector: 1000Base-T
[RS-232C] connector: RS-232C (BAUD RATE: 38.4 kbps/115.2kbps)
[DCP] connector: CAT5e or better Ethernet cable (Straight connected. All 8 pins must be connected.)
[YDIF] connector: CAT5e or better Ethernet STP cable (Straight connected. All 8 pins must be connected.)
Dante [PRIMARY]/[SECONDARY] connector: CAT5e or better Ethernet STP cable
SD Memory card specifications
Supported formats
File formats: FAT32, FAT16, FAT12
Files created on a computer running Windows XP or later, or Mac OS X or later.
Supported capacities
Maximum media capacity: SDHC: Max. 32 GB
SD: Max. 2GB
Maximum file size
(maximum size per file)
Audio file format: WAV
Audio file format: MP3
FAT12: Max. 32MB
FAT16: Max. 2GB
FAT32: Max. 2GB
16bit 2ch PCM
Sampling frequencies: 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz
MPEG-1/2/2.5 Audio Layer-3 sampling frequencies: MPEG-1: 32kHz, 44.1kHz, 48kHz
MPEG-2: 16kHz, 22.05kHz, 24kHz
MPEG-2.5: 8kHz, 11.025kHz
Bit rate: MPEG-1: 32kbps–320kbps, VBR (Variable Bit Rate) * However, free format is excepted.
MPEG-2, 2.5: 8 kbps–160 kbps, VBR (Variable Bit Rate) *However, free format is excepted.
* Specifications and appearance are subject to change without notice for improvement.
European Models
Inrush Current based on EN 55103-1: 2009
2A (on initial switch-on)
2A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
MTX5-D Owner’s Manual
29
Appendix
Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
Input
Terminals
INPUT 1–8
GAIN
+66dB
-6dB
—
Actual Load
Impedance
10kΩ
For Use With
Nominal
50–600Ω Mics
& 600Ω Lines
600Ω Lines
Nominal
Input Level
Max. before clip
-62dBu (0.616mV)
+10dBu (2.45V)
-10dBV (316mV)
-42dBu (6.16mV)
+30dBu (24.5V)
+10dBV (3.16V) ST IN 1, 2 10kΩ
• In these specifications, 0dBu = 0.775 Vrms., 0dBV = 1.00 Vrms.
• All input AD converters are 24bit linear, 128times oversampling.
• +48V DC (phantom power) is supplied to INPUT EUROBLOCK connectors via each individual software controlled switch.
Connector
Euroblock (Balanced)
(5.08mm pitch)
RCA Pin Jack
ANALOG OUTPUT CHARACTERISTICS
Output Terminals
Actual Source
Impedance
For Use With
Nominal
OUTPUT 1–8 75Ω 10kΩ Lines
• In these specifications, 0dBu = 0.775 Vrms.
• All output DA converters are 24bit, 128times oversampling.
Nominal
Output Level
Max. before clip
+4dBu (1.23 V) +24dBu (12.3V)
Connector
Euroblock (Balanced)
(5.08mm pitch)
Dimensions
430
30
MTX5-D Owner’s Manual
480
Unit: mm
Block Diagram
OUTPUT PA
Appendix
IF IN
+ -
INPUT 1-8 ST IN 1LSD IN L-
Mini -YGD
INPUT PAT
MTX5-D Owner’s Manual
31
Appendix
Index
Symbols
+48V .......................................................................12
[
s/t] buttons ...........................................................9
[ALERT] indicator .....................................................9
[DCP] connector .....................................................11
[ENTER] button ........................................................9
[GPI] connector ......................................................10
[INPUT PEAK] indicators ..........................................9
[INPUT SIGNAL] indicators ......................................9
[INPUT] connectors ................................................12
[OUTPUT SIGNAL] indicators ..................................9
[OUTPUT] connectors ............................................12
[POWER] indicator ...................................................9
[PRESET] display .....................................................9
[PRIMARY] connector ............................................12
[PRIMARY] indicator ................................................9
[RS-232C] connector ..............................................10
[SCHEDULER] indicator ...........................................9
[SD/ACT] indicator ....................................................9
[SECONDARY] connector ......................................12
[SECONDARY] indicator ..........................................9
[ST IN] connectors ..................................................12
[SYNC] indicator .......................................................9
[UNIT ID] rotary switch ...........................................10
[YDIF] connectors ...................................................12
[YDIF] indicator .........................................................9
A
AC IN connector .....................................................10
Alert ....................................................................9, 27
B
Block Diagram ........................................................31
C
cable ties ............................................................7, 13
Cascade mode .......................................................17
control panel .............................................................8
Controls and Connectors ..........................................9
Cooling vent ...........................................................10
D
DAISY CHAIN ........................................................11
Daisy chain network ...............................................15
Dante ......................................................................15
DCP ..........................................................................8
DIP switch ..............................................................10
Distribution mode ...................................................17
E
Euroblock plug ........................................7, 10, 12, 13
event .......................................................................20
F
Features ...................................................................8
Front Panel ...............................................................9
G
Ground screw .........................................................10
I
INIT. (INITIALIZE) ..................................................11
Initializing ................................................................22
install ......................................................................17
IP address ..............................................................11
IP SETTING ...........................................................11
L
LOCK ......................................................................11
M
MTX Editor ...............................................................8
O
online ......................................................................19
P
PANEL LOCK .........................................................11
PC ..........................................................................11
phantom power .......................................................12
POWER IN +24V DC .............................................12
Power switch ............................................................9
preset .......................................................8, 9, 18, 19
project file .........................................................18, 19
Q
Quick Guide ............................................................17
R
Rear Panel .............................................................10
REDUNDANT .........................................................11
Redundant networks ..............................................16
RESUME ................................................................11
S
scheduler ................................................................20
schematic diagram .................................................17
SD memory card ................................................9, 22
SD memory card slot ..........................................9, 22
SECONDARY PORT ..............................................11
Slot ...................................................................12, 14
Star network ...........................................................15
START UP MODE ..................................................11
store .......................................................................18
subnet mask ...........................................................17
U
UNIT ID ..............................................................9, 10
UNLOCK ................................................................11
W
wizard .....................................................................17
Y
YDIF .........................................................................8
32
MTX5-D Owner’s Manual
MTX5-D Owner’s Manual
33
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 011-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
PA36
34
MTX5-D Owner’s Manual
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
AFRICA
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, UAE
Tel: +971-4-881-5868
MIDDLE EAST
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli İstanbul
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
Office JAFZA 16-512, P.O.Box 17328,
Jebel Ali - Dubai, U.A.E
Tel: +971-4-881-5868
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
ASIA
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
MEMO
MTX5-D Owner’s Manual
35
Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/
Yamaha Manual Library: http://www.yamaha.co.jp/manual/
C.S.G., PA Development Division
© 2013-2014 Yamaha Corporation
402YJHD-C0
Printed in China
ZE92960
advertisement
Related manuals
advertisement