Kramer VS-41 HDMI HDMI switcher Bedienungsanleitung
Reklamë
Reklamë
Kramer Electronics, Ltd.
USER MANUAL
Model:
VS-41HDMI
4x1 HDMI Switcher
Contents
Contents
1
2
Introduction
Getting Started
2.1
Quick Start
3 Overview
3.1
Defining EDID
3.2
About HDMI
3.3
Recommendations for Best Performance
3.4
Terminology Used in this User Manual
4 Your VS-41HDMI 4x1 Switcher
5
6
Installing the VS-41HDMI on a Rack
Connecting a VS-41HDMI 4x1 HDMI Switcher
7 Operating the VS-41HDMI
7.1
The PC and DVD Modes
7.2
Setting the EDID
7.2.1
Acquiring / Changing the EDID
7.2.2
Resetting the Default EDID
7.3
Controlling via RS-232 (for example, using a PC)
7.4
Controlling the VS-41HDMI via the ETHERNET Port
7.4.1
Connecting the ETHERNET Port directly to a PC (Crossover Cable)
7.5
Configuring the Ethernet Port
7.5.1
Setting a Virtual Port
13
14
14
7.4.2
Connecting the ETHERNET Port via a Network Hub (Straight-Through Cable) 16
7.5.2
Setting an Ethernet Connection
8
9
Technical Specifications
Kramer Protocol 2000
11
12
12
12
5
8
9
11
3
4
5
5
1
1
1
3
16
18
19
20
21
Figures
Figure 1: VS-41HDMI 4x1 HDMI Switcher
Figure 2: Connecting a VS-41HDMI 4x1 HDMI Switcher
Figure 3: Connecting a PC without using a Null-modem Adapter
Figure 4: RJ-45 PINOUT
Figure 5: Local Area Connection Properties Window
Figure 6: Internet Protocol (TCP/IP) Properties Window
Figure 7: The Ethernet Configuration Manager Window
Figure 8: The Virtual Serial Port Manager Window
Figure 9: The Virtual Serial Port Properties Window
Figure 10: The Virtual Serial Port Properties Window (COM 3 and COM 4)
Figure 11: The Port Window – Selecting a Virtual Serial Port
Figure 12: The Port Window – Selecting a Remote Connection
15
15
17
18
6
10
13
14
18
19
19
19 i
Contents
Tables
Table 1: Terminology Used in this User Manual
Table 2: VS-41HDMI 4x1 HDMI Switcher Front Panel Features
Table 3: VS-41HDMI 4x1 HDMI Switcher Rear Panel Features
Table 4: DVD Mode and PC Mode Characteristics
Table 5: Crossover Cable RJ-45 PINOUT
Table 6: Straight-through Cable RJ-45 PINOUT
Table 7: Ethernet Configuration Manager Window Functionality
Table 8: Technical Specifications of the VS-41HDMI
Table 9: Protocol Definitions
Table 10: Instruction Codes for Protocol 2000
14
16
17
20
5
7
7
12
21
22 ii
KRAMER: SIMPLE CREATIVE TECHNOLOGY
ADDENDUM: Ethernet Cross Cable Wiring Connection
This addendum describes the correct wiring for crossover cable connections and replaces the opening paragraph in the "Connecting the ETHERNET Port directly to a PC (Crossover Cable)" section in the User Manual as follows:
Connecting the ETHERNET Port directly to a PC (Crossover Cable)
You can connect the Ethernet port of the machine to the Ethernet port on your
PC, via a crossover cable with RJ-45 connectors.
Table 1 and Figure 1 define the color codes for the two existing standard types of cross cables used in the industry. Table 2 defines how to connect the wires to the connectors on both ends of the cable.
When manually connecting the ends of a cable, both connectors must follow the same standard (either EIA /TIA 568A or EIA /TIA 568B).
Table 1: Crossover Cable RJ-45 Types
EIA /TIA 568B
PIN Wire Color
1
2
EIA /TIA 568A
PIN Wire Color
White-orange 1
Orange 2
White-green
Green
3
4
5
6
7
8
White-green
Blue
White-blue
Green
White-brown
Brown
3
4
5
6
7
8
White-orange
Blue
White-blue
Orange
White-brown
Brown
TOP
FRONT
1 8
1 8
Figure 1: RJ-45 PINOUT
Table 2: Wiring between Connector One and Two of the Cable
Signal Pairs PINs on
Connector One
TX_D1+ 1
TX_D1-
RX_D2+
2
3
RX_D2-
BI_D3+
BI_D3-
BI_D4+
BI_D4-
6
4
5
7
8
8
4
5
2
7
6
1
PINs on Connector
Two
3
Signal Pairs
RX_D2+
RX_D2-
TX_D1+
TX_D1-
BI_D4+
BI_D4-
BI_D3+
BI_D3-
P/N: 2900 - 9999993 A1
Introduction
1 Introduction
Welcome to Kramer Electronics (since 1981): a world of unique, creative and affordable solutions to the infinite range of problems that confront the video, audio and presentation professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our
500-plus different models now appear in 8 Groups 1 by function.
, which are clearly defined
Congratulations on purchasing your Kramer VS-41HDMI 4x1 HDMI Switcher.
The VS-41HDMI is ideal for conference room presentations and advertising applications, as well as for rental and staging.
Each package includes the following items:
VS-41HDMI 4x1 HDMI Switcher
Power cord and Null-modem adapter
Windows®-based Kramer control software 2
Windows®-based Ethernet Configuration Manager and Virtual Serial Port
Manager
Kramer RC-IR1 Infra-Red Remote Control Transmitter required batteries and a separate user manual 4 )
3 (including the
This user manual 4
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging materials for possible future shipment
Review the contents of this user manual
Use Kramer high performance high resolution cables 5
2.1 Quick Start
This quick start chart summarizes the basic setup and operation steps.
1 GROUP 1: Distribution Amplifiers; GROUP 2: Video and Audio Switchers, Matrix Switchers and Controllers; GROUP 3:
Video, Audio, VGA/XGA Processors; GROUP 4: Interfaces and Sync Processors; GROUP 5: Twisted Pair Interfaces;
GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors
2 Downloadable from our Web site at http://www.kramerelectronics.com
3 Previously known as the IR-1 / IR-1-01
4 Download up-to-date Kramer user manuals from our Web site at http://www.kramerelectronics.com
5 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
1
Getting Started
2
Acquired EDID
Output connected
Output not connected
Default EDID
To input
PC Mode
DVD Mode
To input
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
3 Overview
The VS-41HDMI is a high quality 4x1 switcher for HDMI signals.
In particular, the VS-41HDMI:
Supports up to 1.65Gbps bandwidth per graphic channel 1
Has four input selector buttons
Supports HDCP (High Definition Digital Content Protection)
Includes a MUTE button to disconnect the output and a PANEL LOCK button to prevent unwanted tampering with the buttons on the front panel
Fits in one vertical space of a standard 19” professional rack enclosure
Control the VS-41HDMI using the front panel buttons, or remotely via:
RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller
The Kramer infra-red remote control transmitter
The ETHERNET
3.1 Defining EDID
The Extended Display Identification Data (EDID 2 ) is a data-structure, provided by a display, to describe its capabilities to an HDMI source. The
EDID enables the VS-41HDMI to “know” what kind of monitor is connected to the output. The EDID includes the manufacturer’s name, the product type, the timing data supported by the display, the display size, luminance data and
(for digital displays only) the pixel mapping data.
1 Suitable for resolutions up to UXGA at 60Hz, and for all HD resolutions
2 Defined by a standard published by the Video Electronics Standards Association (VESA)
3
Overview
3.2 About HDMI
High-Definition Multimedia Interface (HDMI) is an uncompressed all-digital 1 audio/video interface, widely supported in the entertainment and home cinema industry. It delivers the highest high-definition image and sound quality. Note that
Kramer Electronics Limited is an HDMI Adopter 2 and an HDCP Licensee 3 .
In particular, HDMI:
Provides a simple 4 interface between any audio/video source, such as a set-top box, DVD player, or A/V receiver and video monitor, such as a digital flat LCD / plasma television (DTV), over a single lengthy 5 cable
Supports standard, enhanced, high-definition video, and multi-channel digital audio 6 on a single cable
Transmits all ATSC HDTV standards and supports 8-channel digital audio, with bandwidth to spare to accommodate future enhancements and requirements
Benefits consumers by providing superior, uncompressed digital video quality via a single cable 7 , and user-friendly connector
Is backward-compatible with DVI (Digital Visual Interface)
Supports two-way communication between the video source (such as a
DVD player) and the digital television, enabling new functionality such as automatic configuration and one-button play
HDMI has the capacity to support existing high-definition video formats
(720p, 1080i, and 1080p/60), standard definition formats such as NTSC or
PAL, as well as 480p and 576p.
1 Ensuring an all-digital rendering of video without the losses associated with analog interfaces and their unnecessary digitalto-analog conversions
2 See http://www.hdmi.org/about/adopters_founders.asp
3 See http://www.digital-cp.com/list/
4 With video and multi-channel audio combined into a single cable, the cost, complexity, and confusion of multiple cables currently used in A/V systems is reduced
5 HDMI technology has been designed to use standard copper cable construction at up to 15m
6 HDMI supports multiple audio formats, from standard stereo to multi-channel surround-sound. HDMI has the capacity to support Dolby 5.1 audio and high-resolution audio formats
7 HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a simple, cost-effective manner
4
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your VS-41HDMI 4x1 Switcher
3.3 Recommendations for Best Performance
To achieve the best performance:
Connect only good quality connection cables, thus avoiding interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables)
Avoid interference from neighboring electrical appliances and position your VS-41HDMI away from moisture, excessive sunlight and dust
3.4 Terminology Used in this User Manual
Table 1 defines some terms that are used in this user manual.
Table 1: Terminology Used in this User Manual
Term
802.3
Dynamic Host
Configuration
Protocol (DHCP)
Gateway
IP Address
Local Area Network
(LAN)
Media Access
Control (MAC)
Address
Transmission
Control
Protocol/Internet
Protocol (TCP/IP)
Definition
The standard specification for ETHERNET that is maintained by the Institute of Electrical and Electronics Engineers (IEEE).
Allows the network administrator to distribute IP addresses from a central point and automatically send a new IP address when an Ethernet point is plugged into a different network location
A network position serving as an entry to another network. On the Internet, a node or stopping point can be either a gateway node or a host (end-point) node.
A 32-binary digit number that identifies each sender or receiver (within a network via a particular server or workstation) of data (HTML pages or e-mails) that is sent in packets across the Internet. Every device connected to an IP network must have a unique IP address. This address is used to reference the specific unit.
Computers sharing a common communications line or wireless link, which often share a server within a defined geographic area.
A computer's unique hardware number (or address) in a LAN or other network. On an
Ethernet LAN, the (MAC) address is identical to the Ethernet address.
The basic communication language or protocol of the Internet that breaks the message into appropriately sized packets for the network, and can be used as a communications protocol in an intranet or an extranet.
4 Your VS-41HDMI 4x1 Switcher
Figure 1 illustrates the front and rear panels of the VS-41HDMI. Table 2 and
Table 3 define the front and rear panels of the VS-41HDMI, respectively.
5
Your VS-41HDMI 4x1 Switcher
6
Figure 1: VS-41HDMI 4x1 HDMI Switcher
KRAMER: SIMPLE CREATIVE TECHNOLOGY
2
3
4
5
6
#
1
Your VS-41HDMI 4x1 Switcher
Table 2: VS-41HDMI 4x1 HDMI Switcher Front Panel Features
Feature
IR Receiver
POWER Switch
MUTE Button
INPUT SELECTOR Buttons
EDID Button 1
PANEL LOCK Button
Function
The red LED lights when receiving signals from the
Infra-red remote control transmitter
Illuminated switch for turning the unit ON or OFF
Press to toggle disconnecting the output
Press an INPUT button to select an input (from 1 to 4)
Press to acquire the EDID
Press to toggle disengaging the front panel buttons and to set to the PC/DVD mode
Table 3: VS-41HDMI 4x1 HDMI Switcher Rear Panel Features
#
7
8
9
Feature
INPUT HDMI Connectors
OUTPUT HDMI Connector
RS-232 DB 9F Port
10 ETHERNET Connector
11 RESET Button
Function
Connect to the HDMI sources (from 1 to 4)
Connect to the HDMI acceptor
Connects to the PC or the RS-232 Remote Controller
Connects to the PC or other Ethernet Controller
Press the ETHERNET factory reset button to reset to the factory default definitions 2 :
IP number 192.168.1.39
Mask – 255.255.255.0
Gateway – 192.168.1.1
AC connector enabling power supply to the unit 12 Power Connector with Fuse
1 Illuminates when configuring the EDID
2 First disconnect the power cord and then connect it again while pressing the RESET button. The unit will power up and load its memory with the factory default definitions
7
Installing the VS-41HDMI on a Rack
5 Installing the VS-41HDMI on a Rack
This section describes what to do before installing on a rack and how to rack mount.
Before Installing on a Rack How to Rack Mount
Before installing on a rack, be sure that the environment is within the recommended range:
Operating temperature range +5 to +45 Deg. Centigrade
Operating humidity range 5 to 65 % RHL, non-condensing
Storage temperature range
Storage humidity range
-20 to +70 Deg. Centigrade
5 to 95% RHL, non-condensing
To rack-mount the machine:
1 Attach both ear brackets to the machine. To do so, remove the screws from each side of the machine (3 on each side), and replace those screws through the ear brackets.
5
3
2
4
CAUTION!!
1
When installing on a 19" rack, avoid hazards by taking care that:
It is located within the recommended environmental conditions, as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature.
Once rack mounted, enough air will still flow around the machine.
The machine is placed straight in the correct horizontal position.
You do not overload the circuit(s). When connecting the machine to the supply circuit, overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring. Refer to the appropriate nameplate ratings for information. For example, for fuse replacement, see the value printed on the product label.
The machine is earthed (grounded) in a reliable way and is connected only to an electricity socket with grounding. Pay particular attention to supply connections other than direct connections to the branch circuit (for example, the use of power strips), and that you use only the power cord that is supplied with the machine.
2 Place the ears of the machine against the rack rails, and insert the proper screws (not provided) through each of the four holes in the rack ears.
Note that:
In some models, the front panel may feature built-in rack ears
Detachable rack ears can be removed for desktop use
Always mount the machine in the rack before you attach any cables or connect the machine to the power
If you are using a Kramer rack adapter kit (for a machine that is not
19"), see the Rack Adapters user manual for installation instructions
(you can download it at: http://www.kramerelectronics.com)
8
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Connecting a VS-41HDMI 4x1 HDMI Switcher
6 Connecting a VS-41HDMI 4x1 HDMI Switcher
To connect the VS-41HDMI 4x1 HDMI Switcher (as illustrated in Figure 2), do the following 1 :
1. If required:
Set the appropriate INPUTS to the DVD mode (see section 7.1)
Acquire the EDID (see section 7.2)
2. Connect 2 the HDMI sources as follows 3 :
A multimedia player to INPUT 1
A set top box to INPUT 2
A DVD player to INPUT 3
A DVD player to INPUT 4
3. Connect the OUTPUT HDMI connector to an HDMI acceptor (for example, a plasma display).
4. If required, connect a PC and/or controller to the RS-232 port (see section 7.3) and/or the ETHERNET port (see section 7.4).
5. Connect the power connector to the mains electricity (not shown in Figure 2).
Press an INPUT SELECTOR button (from 1 to 4) to choose which HDMI input to route to the output.
1 Switch OFF the power on each device before connecting it to your VS-41HDMI. After connecting your VS-41HDMI, switch on its power and then switch on the power on each device
2 You do not have to connect all the HDMI sources
3 Alternatively, you can connect a PC to any of the inputs and set those inputs to the PC mode (see section 7.1)
9
Connecting a VS-41HDMI 4x1 HDMI Switcher
RS-232
DVD Player
10
Set Top Box
Source DVD Player
Plasma
Display
Figure 2: Connecting a VS-41HDMI 4x1 HDMI Switcher
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Operating the VS-41HDMI
7 Operating the VS-41HDMI
This section describes:
The PC mode and the DVD mode (see section 7.1)
How to acquire the EDID (see section 7.2)
How to Control the machine via RS-232 (see section 7.3)
How to Control the machine via the ETHERNET port (see section 7.4)
7.1 The PC and DVD Modes
The VS-41HDMI has two operation modes that are specific per input: the PC mode 1 and the DVD mode:
The PC mode is used when connecting a computer or several computers to one or more of the inputs via a DVI-to-HDMI converter cable 2
The DVD mode is used when connecting a DVD or several DVDs to the inputs.
When in the PC mode, the input has access to the EDID (default or acquired) to prevent the computer from resetting if an output is not connected. In the
DVD mode, the EDID of the connected output is available only when the input to which the DVD is connected, is switched to the output.
The PC mode and the DVD mode can be applied to a single unit or to several inputs. For example, if you want to connect a computer to INPUT 1, another computer to INPUT 2, and DVD machines to INPUT 3 and INPUT 4, set
INPUT 1 and INPUT 2 to the PC mode and INPUT 3 and INPUT 4 to the
DVD mode.
To set the inputs to either the PC or DVD mode, do the following:
1. Turn the POWER off.
2. Press the PANEL LOCK button while turning the POWER on again.
The INPUT buttons blink simultaneously.
3. Keep pressing and holding the PANEL LOCK button for a few seconds and then release it.
The LOCK button blinks.
If an input button illuminates, this indicates that that input is set to the DVD mode.
If an input button is not illuminated, this indicates that that input is set to the
PC mode.
1 The default
2 For example, the Kramer HDMI-DVI Gold Plated Cable in various lengths (3” , 6” , 10” and 15” )
11
Operating the VS-41HDMI
4. Toggle between the PC mode (input button not illuminated) and the DVD mode (input button illuminated) by pressing that input.
5. Press the PANEL LOCK button to exit this mode.
6. You can connect a computer to the input(s) that is set to the PC mode and a
DVD to the input(s) that is set to the DVD mode.
Table 4 summarizes the differences between the PC mode and the DVD mode:
Table 4: DVD Mode and PC Mode Characteristics
PC Mode
The input is connected to a computer
The EDID is available at all times (to prevent computer reset)
The input EDID source is the default EDID or an acquired EDID (see section 7.2)
DVD Mode
The input is connected to a multimedia application, such as a DVD, a set top box and so on
The EDID is available only when that input is connected to an output
The input EDID source is acquired directly from the connected output
7.2 Setting the EDID
You can acquire or change the EDID (see section 7.2.1) or reset the machine to the default EDID (see section 7.2.2).
7.2.1 Acquiring / Changing the EDID
You can work with the default EDID or acquire or change an EDID via the connected output. Use the EDID button to acquire the output EDID information.
To acquire or change the EDID of a new output display:
1. Connect the power supply.
2. Connect the new output display device.
3. Press the EDID button.
The INPUT buttons blink in sequence until the EDID is acquired.
7.2.2 Resetting the Default EDID
To reset the default EDID, disconnect the output and repeat the steps in section 7.2.1.
12
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Operating the VS-41HDMI
7.3 Controlling via RS-232 (for example, using a PC)
To connect a PC to the VS-41HDMI unit, using the Null-modem adapter provided with the machine (recommended):
Connect the RS-232 DB9 rear panel port on the VS-41HDMI unit to the
Null-modem adapter and connect the Null-modem adapter with a 9-wire flat cable to the RS-232 DB9 port on your PC
To connect a PC to the VS-41HDMI unit, without using a Null-modem adapter:
Connect the RS-232 DB9 port on your PC to the RS-232 DB9 rear panel port on the Master VS-41HDMI unit, as Figure 3 illustrates
PIN 5 Connected to PIN 5 (Ground)
PIN 3 Connected to PIN 2
PIN 2 Connected to PIN 3
Female DB9 (From PC)
PIN 4 Connected to PIN 6
PINS 8, 7, 1 Connected together
If a Shielded cable is used, connect the shield to PIN 5
Male DB9
Figure 3: Connecting a PC without using a Null-modem Adapter
13
Operating the VS-41HDMI
7.4 Controlling the VS-41HDMI via the ETHERNET Port
You can connect the VS-41HDMI via the Ethernet, using a crossover cable
(see section 7.4.1) for direct connection to the PC or a straight through cable
(see section 7.4.2) for connection via a network hub or network router.
7.4.1 Connecting the ETHERNET Port directly to a PC (Crossover Cable)
You can connect the Ethernet port of the VS-41HDMI to the Ethernet port on your PC, via a crossover cable with RJ-45 connectors, as Table 5 and Figure 4 define.
Figure 4: RJ-45 PINOUT
14
Table 5: Crossover Cable RJ-45 PINOUT
5
6
3
4
EIA /TIA 568A
Side 1
PIN Wire Color
1 White-orange
2 Orange
White-green
Blue
White-blue
Green
7
8
White-brown
Brown
Pair 1 4 and 5
Pair 2 1 and 2
Pair 3 3 and 6
Pair 4 7 and 8
5
6
3
4
EIA /TIA 568B
Side 2
PIN Wire Color
1 White-green
2 Green
White-orange
Blue
White-blue
Orange
7
8
White-brown
Brown
Pair 1 4 and 5
Pair 2 3 and 6
Pair 3 1 and 2
Pair 4 7 and 8
This type of connection is recommended for identification of the factory default
IP Address of the VS-41HDMI during the initial configuration
After connecting the Ethernet port, configure your PC as follows:
1. Right-click the My Network Places icon on your desktop.
2. Select Properties.
3. Right-click Local Area Connection Properties.
4. Select Properties.
The Local Area Connection Properties window appears.
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Operating the VS-41HDMI
5. Select the Internet Protocol (TCP/IP) and click the Properties Button (see
Figure 5).
Figure 5: Local Area Connection Properties Window
6. Select Use the following IP Address, and fill in the details as shown in
Figure 6.
7. Click OK.
Figure 6: Internet Protocol (TCP/IP) Properties Window
15
Operating the VS-41HDMI
7.4.2 Connecting the ETHERNET Port via a Network Hub (Straight-Through
Cable)
You can connect the Ethernet port of the VS-41HDMI to the Ethernet port on a network hub or network router, via a straight-through cable with RJ-45 connectors, as Table 6 defines:
Table 6: Straight-through Cable RJ-45 PINOUT
4
5
6
7
8
2
3
Side 1
PIN
1
Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
4
5
6
7
8
2
3
Side 2
1
PIN Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
7.5 Configuring the Ethernet Port
To configure the ETHERNET port, do the following:
1. Connect the ETHERNET port as described in section 7.4.1.
2. Insert the CD-ROM in the CD-ROM drive, double click the Set
Setfc11eth_confxx.exe
1 file and follow the on-screen instructions 2 .
The Ethernet Configuration Manager is installed.
3. Click the appropriate shortcut in the Start menu’s Programs folder. The
Configuration Manager window (see Figure 7) opens.
4. Click the Search button 3 (or the Action menu’s, Search Board command).
The MAC Address for the found ETHERNET port appears in the Device List.
5. Change the settings according to your network requirements and then click the
Config button (or the Action menu’s, Config command) to apply the settings.
Note, that clicking the Config button will alter the IP settings of the
ETHERNET port
1 File names are liable to change from time to time
2 The latest version appears on our Web site at http://www.kramerelectronics.com
3 To automatically search for devices
16
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Operating the VS-41HDMI
4
5
2
3
6
1
#
7
8
Feature
File
Action
Figure 7: The Ethernet Configuration Manager Window
Table 7: Ethernet Configuration Manager Window Functionality
Set MAC 1
About
Device List
Progress Bar
Status Bar
Version
Device Network
Settings Area
Action Buttons
Exit Button
Function
The Exit command closes the Configuration Manager application
The Search Board command seeks the VS-41HDMI device that connects to the PC via the ETHERNET port, and displays it and its corresponding settings;
The Config command adjusts the VS-41HDMI according to the displayed data
For factory use only (click the Password command to enter the password)
Displays software information, including the software version
Displays the MAC Address
Shows the progress
Shows the status
Displays the firmware version
DHCP 1 Mode Check Box: When selected, configures the Ethernet port to obtain an IP address automatically from the DHCP server. When cleared, manual configuration of the Ethernet port is required to obtain an IP address (Static IP)
IP Address: A 32-binary digit number obtained from your Network Administrator that identifies the Ethernet port that is currently being configured
Subnet: A 32-binary digit number obtained from your Network Administrator, which combined with the IP Address, identifies which network your device is on
Gateway: A network position serving as an entry to another network or to the Internet
(only relevant in the Active Routing mode)
Search: seeks the devices that connect to the PC via the ETHERNET port, and displays them and their corresponding settings
Config: adjusts the according to the displayed data
Closes the Configuration Manager application
1 See the definition in Table 1
17
Operating the VS-41HDMI
7.5.1 Setting a Virtual Port
If the control application cannot work with an Ethernet driver, use the Kramer
Virtual port driver as follows:
1. Run the Virtual Serial Port Manager Application.
The Virtual Serial Port Manager window appears (see Figure 8).
Figure 8: The Virtual Serial Port Manager Window
2. Press the Add VSP button to add a serial port and type the IP settings according to the IP address and local port of your VS-41HDMI (see Figure 9).
18
Figure 9: The Virtual Serial Port Properties Window
3. You can set a virtual port for each local port on your VS-41HDMI (see
Figure 10).
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Operating the VS-41HDMI
Figure 10: The Virtual Serial Port Properties Window (COM 3 and COM 4)
4. In the control application, choose the COM-port connection according to your virtual serial port connections (see Figure 11).
Figure 11: The Port Window – Selecting a Virtual Serial Port
7.5.2 Setting an Ethernet Connection
If the control application can connect directly to the Ethernet driver, select the host IP and port number, as illustrated in Figure 12.
Figure 12: The Port Window – Selecting a Remote Connection
19
Technical Specifications
8 Technical Specifications
Table 8 includes the technical specifications:
Table 8: Technical Specifications
1
of the VS-41HDMI
INPUTS:
OUTPUT:
BANDWIDTH:
COMPLIANCE WITH
HDMI STANDARD:
RESOLUTION:
4 HDMI Connectors
1 HDMI Connector
Supports up to 1.65Gbps bandwidth per graphic channel
Supports HDMI 1.2 and HDCP
Up to UXGA; 1080p
POWER SOURCE: 100 264VAC; 50/60Hz, 10VA
CONTROLS: Front panel buttons, Infra-red remote control transmitter, RS-232, Ethernet
DIMENSIONS:
WEIGHT:
ACCESSORIES:
OPTIONS:
19-inch (W), 7-inch (D), 1U (H)
2.5 kg. (5.5 lbs.) approx.
Power cord
Kramer HDMI cables 2
1 Specifications are subject to change without notice
2 For best results, use Kramer cables such as the C-HDMI/HDMI series, the C-HDMI-DVI series and/or our HDMI over fiber optics C-FOHM/FOHM series
20
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Kramer Protocol 2000
9 Kramer Protocol 2000
1
The VS-41HDMI is compatible with Kramer’s Protocol 2000 (version 0.46)
(below). This RS-232/RS-485 communication protocol uses four bytes of information as defined below. For RS-232, a null-modem connection between the machine and controller is used. The default data rate is 9600 baud, with no parity, 8 data bits and 1 stop bit.
Table 9: Protocol Definitions
MSB
0
7
1st byte
1
7
2nd byte
1
7
3rd byte
DESTI-
NATION
D
6
INPUT
I6
6
OUTPUT
O6
6
INSTRUCTION
N5
5
I5
5
O5
5
N4
4
I4
4
O4
4
N3
3
I3
3
O3
3
N2
2
I2
2
O2
2
N1
1
I1
1
O1
1
LSB
N0
0
I0
0
O0
0
MACHINE NUMBER
1
7
4th byte
OVR
6
X
5
M4
4
M3
3
1 st BYTE: Bit 7 – Defined as 0.
D – “DESTINATION” : 0 - for sending information to the switchers (from the PC);
M2
2
M1
1
M0
0
1 - for sending to the PC (from the switcher).
N5…N0 – “INSTRUCTION”
The function that is to be performed by the switcher(s) is defined by the INSTRUCTION (6 bits). Similarly, if a function is performed via the machine’s keyboard, then these bits are set with the INSTRUCTION NO., which was performed. The instruction codes are defined according to the table below (INSTRUCTION NO. is the value to be set for N5…N0).
2 nd Bit 7 – Defined as 1.
I6…I0 – “INPUT” .
BYTE:
When switching (ie. instruction codes 1 and 2), the INPUT (7 bits) is set as the input number which is to be switched.
3
Similarly, if switching is done via the machine’s front-panel, then these bits are set with the INPUT NUMBER which was switched. For other operations, these bits are defined according to the table. rd BYTE: Bit 7 – Defined as 1.
O6…O0 – “OUTPUT” .
When switching (ie. instruction codes 1 and 2), the OUTPUT (7 bits) is set as the output number which is to be switched.
4
Similarly, if switching is done via the machine’s front-panel, then these bits are set with the OUTPUT NUMBER which was switched. For other operations, these bits are defined according to the table. th BYTE: Bit 7 – Defined as 1.
Bit 5 – Don’t care.
OVR – Machine number override.
M4…M0 – MACHINE NUMBER.
Used to address machines in a system via their machine numbers. When several machines are controlled from a single serial port, they are usually configured together with each machine having an individual machine number. If the OVR bit is set, then all machine numbers will accept (implement) the command, and the addressed machine will reply.
1 You can download our user-friendly “Software for Calculating Hex Codes for Protocol 2000” from our Web site: http://www.kramerelectronics.com
21
Kramer Protocol 2000
For a single machine controlled via the serial port, always set M4…M0 = 1, and make sure that the machine itself is configured as MACHINE NUMBER = 1.
Table 10: Instruction Codes for Protocol 2000
Note: All values in the table are decimal, unless otherwise stated.
INSTRUCTION DEFINITION FOR SPECIFIC INSTRUCTION
# DESCRIPTION
0 RESET VIDEO
1 SWITCH VIDEO
2 SWITCH AUDIO
3 STORE VIDEO
STATUS
4 RECALL VIDEO
STATUS
5 REQUEST STATUS
OF A VIDEO OUTPUT
6 REQUEST STATUS
OF AN AUDIO
OUTPUT
7 VIS SOURCE
INPUT
0
Set equal to video input which is to be switched
(0 = disconnect)
Set equal to audio input which is to be switched
(0 = disconnect)
Set as SETUP #
Set as SETUP #
Set as SETUP #
Set as SETUP #
OUTPUT
0
Set equal to video output which is to be switched
(0 = to all the outputs)
Set equal to audio output which is to be switched
(0 = to all the outputs)
0 - to store
1 - to delete
0
Equal to output number whose status is reqd
Equal to output number whose status is reqd
8
9
BREAKAWAY
SETTING
VIDEO / AUDIO TYPE
SETTING
10 REQUEST VIS
SETTING
11 REQUEST
BREAKAWAY
SETTING
12 REQUEST VIDEO /
AUDIO TYPE
SETTING
13 SET HIGHEST
MACHINE ADDRESS
14 REQUEST HIGHEST
MACHINE ADDRESS
0
1
Set as input # when
OUTPUT byte = 6;
OR set as output # when
OUTPUT byte = 7;
OR set as blank period
(in steps of 25ms) when
OUTPUT byte = 32;
OR set = 0. *****
0 - for video
1 - for audio
2 - for VGA and DVI
Set as SETUP #, or set to 126 or 127 to request if machine has this function
Set as SETUP #, or set to 126 or 127 to request if machine has this function
Set as SETUP #, or set to 126 or 127 to request if machine has this function
0 - for video
1 - for audio
0 - for video
1 - for audio
0 - No VIS (immediate)
1 - Input # 1
2 - External digital sync
3 - External analog sync
4 - Dynamic sync
5 - Inter-machine sync
6 - Input # (INPUT byte)
7 - Output #(INPUT byte)
8 - User-defined sync
32 - RGBHV seamless switching
64 - Set for delayed switch
65 - Execute delayed switch
66 - Cancel delayed switch setting
0 - audio-follow-video
1 - audio breakaway
0 - FOLLOW mode
1 - Normal mode
0 - CV
1 - YC
2 - YUV
3 - RGBS
4 - SDI
5 - CV+YC
6 - VGA scaler
7 - DVI
O0=0 – Unbalanced audio
O0=1 – Balanced audio
O1=0 – Digital audio
O1=1 – Analog audio
O4=0, O3=0, O2=0-Mono
O4=0, O3=0,O2=1-Stereo
1 - 640X480
2 - 800X600
3 - 1024X768
0 - VIS source
1 - Input # or output # of source
2 - Vertical sync freq (Hz)
0 - Request audio breakaway
setting
1 - Request “FOLLOW” setting
0 - for video
1 - for audio
2 - for VGA
Set equal to highest machine address
0
NOTE
1
2, 15
2
2, 3, 15
2, 3, 15
4, 3
4, 3
2, 5, 17, 18
2
15
2
3, 4, 6, 7
3, 4, 6, 15
3, 4, 6
2
4
22
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Kramer Protocol 2000
INSTRUCTION
# DESCRIPTION
15 REQUEST WHETHER
SETUP IS DEFINED /
VALID INPUT IS
DETECTED
16 ERROR / BUSY
17 RESERVED
18 RESET AUDIO
19 STORE AUDIO
STATUS
20 RECALL AUDIO
STATUS
21 SET VIDEO
PARAMETER
DEFINITION FOR SPECIFIC INSTRUCTION
INPUT
SETUP # or
Input #
For invalid / valid input (i.e.
OUTPUT byte = 4 or OUTPUT byte
= 5),
This byte is set as the input #
- - - -
0
Set as SETUP #
Set as SETUP #
OUTPUT
0 - for checking if setup is defined
1 - for checking if input is valid
0 - error
1 - invalid instruction
2 - out of range
3 - machine busy
4 - invalid input
5 - valid input
- - - -
0
0 - to store
1 - to delete
0
8
NOTE
9, 25
10
1
2, 3
2, 3
2, 11, 24
22 SET AUDIO
PARAMETER
23 INCREASE /
DECREASE VIDEO
PARAMETER
24 INCREASE /
DECREASE AUDIO
PARAMETER
25 REQUEST AUDIO
PARAMETER
Equal to input / output number whose video parameter is to be set
(0 = all)
Equal to input / output number whose gain is to be set
(0 = all)
Equal to input / output number whose video parameter is to be increased / decreased
(0 = all)
Equal to input / output number whose parameter is to be increased / decreased
(0 = all)
Equal to input / output number whose parameter is requested
Set as parameter value
Set as parameter value
0 - increase video gain
1 - decrease video gain
2 - increase contrast
3 - decrease contrast
4 - increase brightness
5 - decrease brightness
6 - increase color
7 - decrease color
8 - increase hue
9 - decrease hue
16 - increase H-phase
17 - decrease H-phase
18 - increase V-position
19 - decrease V-position
0 - increase output
1 - decrease output
2 - increase left output
3 - decrease left output
4 - increase right output
5 - decrease right output
6 - increase input
7 - decrease input
8 - increase left input
9 - decrease left input
10 - increase right input
11 - decrease right input
0
2, 11, 24
24
24
6, 24
26 REQUEST VIDEO
PARAMETER
Equal to input / output number whose video parameter is requested
30 LOCK FRONT PANEL 0 - Panel unlocked
1 - Panel locked
31 REQUEST WHETHER
PANEL IS LOCKED
RESERVED
0
- - - - 32 to
35
40 DIRECT MEMORY
SAVE
Memory address
0
0
0
- - - -
Data
6, 24
2
16
10
20
23
Kramer Protocol 2000
INSTRUCTION
# DESCRIPTION
42 AUDIO PARAMETER
SETTINGS FOR
INSTRUCTIONS 22,
24, 25
43 VIDEO PARAMETER
SETTINGS FOR
INSTRUCTIONS 21,
23, 26
56 CHANGE TO ASCII
57 SET AUTO-SAVE
58 EXECUTE LOADED
DATA
59 LOAD VIDEO DATA
60 LOAD AUDIO DATA
DEFINITION FOR SPECIFIC INSTRUCTION
INPUT
INPUT Bit:
I0 - 0=input; 1=output
I1 - Left
I2 - Right
1 – Input
2 – Output
OUTPUT
0 - Gain
1 - Bass
2 - Treble
3 - Midrange
0
I3 - no save
I4 - auto-save
Set as 0, or as SETUP #.
0 - video gain
1 - contrast
2 - brightness
3 - color
4 - hue
5 - H-phase
6 - V-position
1 - SVS protocol
2 - Generic protocol
0
Set equal to video input
(0 = disconnect)
1-Take
2-Cancel
Set equal to video output
(0 = to all the outputs)
(127 = load SETUP #)
Set equal to audio input
(0 = disconnect) or SETUP #
Set equal to audio output
(0 = to all the outputs)
NOTE
24
24
19
12, 2
22, 3
22, 23
22, 23
(127 = load SETUP #) or SETUP #
61 IDENTIFY MACHINE 1 - video machine name
2 - audio machine name
3 - video software version
4 - audio software version
5 - RS422 controller name
6 - RS422 controller version
7 - remote control name
8 - remote software version
62 DEFINE MACHINE
9 - Protocol 2000 revision
1 - number of inputs
2 - number of outputs
3 - number of setups
0 - Request first 4 digits
1 - Request first suffix
2 - Request second suffix
3 - Request third suffix
10 - Request first prefix
11 - Request second prefix
12 - Request third prefix
1 - for video
2 - for audio
3 - for SDI
4 - for remote panel
5 - for RS-422 controller
7 MSBs for OUTPUT data
13
14
63 EXTENDED DATA
NOTES on the above table:
7 MSBs for INPUT data 20
NOTE 1 - When the master switcher is reset, (e.g. when it is turned on), the reset code is sent to the PC. If this code is sent to the switchers, it will reset according to the present power-down settings.
NOTE 2 - These are bi-directional definitions. That is, if the switcher receives the code, it will perform the instruction; and if the instruction is performed (due to a keystroke operation on the front panel), then these codes are sent. For example, if the
HEX code
01 85 88 83 was sent from the PC, then the switcher (machine 3) will switch input 5 to output 8. If the user switched input 1 to output 7 via the front panel keypad, then the switcher will send HEX codes:
41 81 87 83 to the PC.
When the PC sends one of the commands in this group to the switcher, then, if the instruction is valid, the switcher replies by sending to the PC the same four bytes that it was sent (except for the first byte, where the DESTINATION bit is set high).
NOTE 3 - SETUP # 0 is the present setting. SETUP # 1 and higher are the settings saved in the switcher's memory, (i.e. those used for Store and Recall).
NOTE 4 - The reply to a "REQUEST" instruction is as follows: the same instruction and INPUT codes as were sent are returned, and the OUTPUT is assigned the value of the requested parameter. The replies to instructions 10 and 11 are as per the definitions in instructions 7 and 8 respectively. For example, if the present status of machine number 5 is breakaway setting, then the reply to the HEX code
0B 80 would be HEX codes
4B 80
80
81
85
85
24
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Kramer Protocol 2000
NOTE 5 – For the OUTPUT byte set as 6, the VIS source is the input selected using the OUTPUT byte. Similarly, for the
OUTPUT byte set as 7, the VIS source is the output selected using the OUTPUT byte. Note also, that on some machines the sync source is not software selectable, but is selected using switches, jumpers, etc!
NOTE 6 – If INPUT is set to 127 for these instructions, then, if the function is defined on this machine, it replies with
OUTPUT=1. If the function is not defined, then the machine replies with OUTPUT=0, or with an error (invalid instruction code).
If the INPUT is set to 126 for these instructions, then, if possible, the machine will return the current setting of this function, even for the case that the function is not defined. For example, for a video switcher which always switches during the VIS of input #1, (and its VIS setting cannot be programmed otherwise), the reply to the HEX code
0A FE would be HEX codes
FE
80 81 (ie. request VIS setting, with INPUT set as 126 dec
)
4A 81 81 (ie. VIS setting = 1, which is defined as VIS from input #1).
NOTE 7 – Setting OUTPUT to 0 will return the VIS source setting as defined in instruction #7. Setting to 1 will return the input # or output # of the sync source (for the case where the VIS source is set as 6 or as 7 in instruction #7). Setting to 2 returns the vertical sync frequency (0 for no input sync, 50 for PAL, 60 for NTSC, 127 for error).
NOTE 8 - The reply is as in TYPE 3 above, except that here the OUTPUT is assigned with the value 0 if the setup is not defined / no valid input is detected; or 1 if it is defined / valid input is detected.
NOTE 9 - An error code is returned to the PC if an invalid instruction code was sent to the switcher, or if a parameter associated with the instruction is out of range (e.g. trying to save to a setup greater than the highest one, or trying to switch an input or output greater than the highest one defined). This code is also returned to the PC if an RS-232 instruction is sent while the machine is being programmed via the front panel. Reception of this code by the switcher is not valid.
NOTE 10 – This code is reserved for internal use.
NOTE 11 – For machines where the video and / or audio gain is programmable.
NOTE 12 - Under normal conditions, the machine's present status is saved each time a change is made. The "power-down" save (auto-save) may be disabled using this code. Note that whenever the machine is turned on, the auto-save function is set.
NOTE 13 - This is a request to identify the switcher/s in the system. If the OUTPUT is set as 0, and the INPUT is set as 1, 2,
5 or 7, the machine will send its name. The reply is the decimal value of the INPUT and OUTPUT. For example, for a 2216, the reply to the request to send the audio machine name would be (HEX codes):
7D 96 90 for 2 nd byte, and 128 dec
+ 16 dec
for 3 rd byte). 81 (i.e. 128 dec
+ 22 dec
If the request for identification is sent with the INPUT set as 3 or 4, the appropriate machine will send its software version number. Again, the reply would be the decimal value of the INPUT and OUTPUT - the INPUT representing the number in front of the decimal point, and the OUTPUT representing the number after it. For example, for version 3.5, the reply to the request to send the version number would be (HEX codes):
7D 83 85 + 5 dec
for 3 81 (i.e. 128 dec
+ 3 dec
for 2 nd byte, 128 dec rd byte).
If the OUTPUT is set as 1, then the ASCII coding of the lettering following the machine’s name is sent. For example, for the
VS-7588YC, the reply to the request to send the first suffix would be (HEX codes):
7D D9 C3 + ASCII for “C” ). 81 (i.e. 128 dec
+ ASCII for “Y” ; 128 dec
NOTE 14 - The number of inputs and outputs refers to the specific machine which is being addressed, not to the system. For example, if six 16X16 matrices are configured to make a 48X32 system (48 inputs, 32 outputs), the reply to the HEX code
81 82 (ie. request the number of outputs) 3E 82 would be HEX codes
7E ie. 16 outputs
82 90 82
NOTE 15 – When the OVR bit (4 th byte) is set, then the “video” commands have universal meaning. For example, instruction
1 (SWITCH VIDEO) will cause all units (including audio, data, etc.) to switch. Similarly, if a machine is in “FOLLOW” mode, it will perform any “video” instruction.
NOTE 16 - The reply to the “REQUEST WHETHER PANEL IS LOCKED” is as in NOTE 4 above, except that here the
OUTPUT is assigned with the value 0 if the panel is unlocked, or 1 if it is locked.
NOTE 17 – For clean switching of RGBHV video, the “seamless switching” option may be used. The blanking period for the transition of the RGB sources may be set in this case, in steps of 25 milliseconds.
For example, to set for 350ms blanking time (14 steps), send HEX codes
07 8E A0 81
25
Kramer Protocol 2000
NOTE 18 – Delayed execution allows switching after a delay dictated by RS-232. To do this, the user sends instruction 7 with the “Set for delayed switch” option (64 dec
) before sending the switch command (instruction 1) or pressing via front panel.
The switch is not executed (unless timed-out) until the “Execute delayed switch” code is sent, or the “Set for delayed switch” code is sent again. (The mode is automatically cancelled after implementation of the switch if the “execute” command is used).
For example, to connect input 4 to output 3 after a delay, send HEX codes
07
01
80
84
C0
83
81
81
(set for delayed switch)
(switch code) then, after the required delay, send HEX codes
07 C1 81 80 to implement the switch.
(execute delayed switch)
NOTE 19 – After this instruction is sent, the unit will respond to the ASCII command set defined by the OUTPUT byte. The
ASCII command to operate with the HEX command set must be sent in order to return to working with HEX codes.
NOTE 20 – When data (ie. the INPUT and/or OUTPUT bytes) of more than 7 bits is required, this instruction is sent before sending the instruction needing the additional bits. The data in this intruction then becomes the Most Significant Bits of that dec
(2A9 hex
), you would first send HEX next instruction. For example, to set the audio gain (instruction 22) of output 3 to 681 codes
3F and then send HEX codes
3F
followed by HEX codes
16
80
16 83
To set the audio gain of output 6 to 10013
A9
80
85 dec
(271D
CE hex
81
81.
), first send HEX codes
81
86 9D 81.
NOTE 21 – To store data in the non-volatile memory of the unit, eg. the EEPROM for saving SETUPS. The EEPROM address is sent using the INPUT byte, and the data to be stored is sent using the OUTPUT byte. To use this instruction, it is necessary to understand the memory map, and memory structure of the particular machine.
NOTE 22 – Instruction 59 and instruction 60 load data for sending to the crosspoint switcher (or for storing in a SETUP), ie. the data is “lined-up” to be executed later. Instruction 58 executes the loaded data.
NOTE 23 – If the INPUT byte is set as 127 dec
, then the data stored in a SETUP is loaded. The SETUP # is in the OUTPUT byte.
NOTE 24 – Further information needed in instructions 21, 22, 25 and 26, is sent using instruction 42 – which is sent prior to the instruction. For example, to request the audio gain value of right input # 9, send hex codes
2A and then send HEX codes
19
84 80
81
81
89 81.
NOTE 25 – For units which detect the validity of the video inputs, Instruction 16 will be sent whenever the unit detects a change in the state of an input (in real-time).
For example, if input 3 is detected as invalid, the unit will send the HEX codes
10 83 84 81
If input 7 is detected as valid, then the unit will send HEX codes
10 87 85 81.
26
KRAMER: SIMPLE CREATIVE TECHNOLOGY
LIMITED WARRANTY
Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms.
HOW LONG IS THE WARRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
WHO IS PROTECTED?
Only the first purchase customer may enforce this warranty.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty:
1. Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the Web site www.kramerelectronics.com.
2.
3.
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from: i) ii) iii) iv) v) vi)
Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
Product modification, or failure to follow instructions supplied with the product
Repair or attempted repair by anyone not authorized by Kramer
Any shipment of the product (claims must be presented to the carrier)
Removal or installation of the product
Any other cause, which does not relate to a product defect vii) Cartons, equipment enclosures, cables or accessories used in conjunction with the product
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1.
2.
3.
Removal or installations charges.
Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the responsibility of the Kramer dealer from whom the product was purchased.
Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1.
2.
3.
To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage, and should be included in any shipment of the product. Please also include in any mailing a contact name, company, address, and a description of the problem(s).
For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WARRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to the length of this warranty.
EXCLUSION OF DAMAGES
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer shall not be liable for:
1.
2.
Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss of time, commercial loss; or:
Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
This equipment has been tested to determine compliance with the requirements of:
EN-50081:
EN-50082:
"Electromagnetic compatibility (EMC); generic emission standard.
Part 1: Residential, commercial and light industry"
"Electromagnetic compatibility (EMC) generic immunity standard.
CFR-47:
Part 1: Residential, commercial and light industry environment".
FCC Rules and Regulations:
Part 15: “Radio frequency devices
Subpart B – Unintentional radiators”
CAUTION!
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.
27
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Caution
Safety Warning:
Disconnect the unit from the power supply before opening/servicing.
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: [email protected]
P/N: 2900-000191 REV 1
Shkarko
Lidhja publike u përditësua
Lidhja publike për bisedën tuaj është përditësuar. You may view and manage your chat links after registration here.
Lidhja publike e dokumentit
Reklamë