ELLA LOW THRESHOLD GEL COAT SHOWERS

OWNER'S MANUAL

REPRESENTING THESE MODEL NUMBERS:

3648 SH 1S 3P 4.0

Right Seat/Left Seat

6032 SH 1S 3P 4.0

Right Seat/Left Seat

4836 SH 4P 3.0

Center Drain

6033 SH 5P 4.0

Center Drain

6030 SH 5P 4.0

Right/Left Drain

Contents

Getting Started ................................................................................................................................... 1

Installation Procedure ..................................................................................................................... 2-4

Limited Warranty ................................................................................................................................ 5

Framing Dimensions ........................................................................................................................... 6

Shower Diagrams ............................................................................................................................... 7

Warranty Information ........................................................................................................................ 8

Warranty Activation Form .............................................................................................................9-10 www.ellasbubbles.com 03/14

Getting Started

Thank you for purchasing an Ella Low Threshold Shower System. For best results, please read and follow all directions carefully before beginning installation.

Tools/Materials you might need for proper installation:

• 6D Galvanized Screws

• 100% silicone caulking

• Caulking gun

• Acrylic latex caulk

• Shims

• Tape measure

• 1/8" drill bit

• Phillips screw driver

• Cardboard

• China marker / grease pencil

• Furring strips

• Construction adhesive

• Long spirit level

IMPORTANT! READ ALL INSTRUCTIONS

1. The back of a fiberglass unit is not waterproof. Unit must be stored so water will drain off and not acumulate in one spot. Water can penetrate the back laminates and soak the glassed in reinforcement supports causing bulges in the gelcoat unit.

2. Most handling damage is the result of impact blows to the back of hte fiberglass units.

3. Never drag a fiberglass unit on any surface. Always transport the unit y hand using (2) people or two wheel dolly.

4. Never let a fiberglass unit drop from any height, not even an inch or stress cracks are likely to occur.

SECTIONAL GELCOAT BATHING SYSTEMS

working inside the shower.

6. Never clean fiberglass gelcoat surface with metal tools of any kind, including razor blades.

INSTALLATION

INSTRUCTIONS

Pre-Installation Planning

READ INSTRUCTIONS COMPLETELY

BEFORE BEGINNING INSTALLATION.

1.

Do Not store units out of doors.- Keep

out of sunlight and exposure to weather.

2.

alcove is required, approved finish material must be installed prior to unit installation. Access to drain and supply connections should be provided so that these connections may be made after the unit has been installed. Framing alcove must reflect interior dimensions on diagram to permit installation of unit. Note in diagram the required opening in the floor to provide clearance for the drain fitting and connection.

Figure 1

Wood Support Shims

3.

support of the base unit. See Figure 1.

Installation Procedure

1.

area. Apply a bead of silicone to all joints. Reinstall wall sections. Align all parts, and connect with the metal fasteners. Wipe away any excess caulk that squeezes out. The unit will be installed in the framed alcove as a one-piece unit.

It is MANDATORY that these wedges are in place and in proper contact to assure structural integrity of the bathing unit.

Page 1

Two wood shims are provided in the installation packet attached to the unit. Additonal shims may be added by the installer.

03/14

Alternate Connection: Plastic Fasteners:

If installing piece-by-piece into the alcove, use the plastic fasteners. These fasteners permit a “blind” installation so shower parts may connected together in the installation location.

The unit parts are held in alignment with the plastic fastener pins. When the caulking cures, the parts are solidly held together similar to a one piece unit when attached to the framing.

Follow the instructions on Pages 2 and 3 if using the plastic fasteners in place of the metal fasteners.

5 .

finished flat area at the top of the wall. Once the unit is leveled, if any gap appears between the apron and sub floor fill the gap with solid material. When satisfied with the fit, attach the unit to framing with 6d galvanized nails or screws through the predrilled holes in the mounting flanges. If required, drill additional holes through the flanges in order to attach the unit to each stud.

6.

lines. Strap all lines to the framing. Install finish trim. Caulk as necessary.

2.

manufacturers instructions. Apply a bead of 100% silicone caulk around the drain opening in unit before installing the fitting.

3.

of fittings on the finished side of the unit. Recheck locations, and drill 1/4’’ pilot holes. Cut holes to final size using the appropriate size hole saw.

8.

Finish wall board as detailed in the diagram.

Wall

Board

Figure 2

Shim Along

Framing Framing

4.

to final location and tilt unit into place. Make certain that the wood shims contact both the bathing unit and sub floor. Remove and adjust wedges if necessary to assure proper contact for support.

Caulk

Gap

Mounting

Flange

1

Installation Procedure 1 of 3

1. Remove wall section(s) from the base unit. Carefully move all parts into the installation area. Apply a bead of silicone to all joints. Reinstall wall sections. Align all parts, and connect using the alignment pins. Wipe away any excess caulk that squeezes out. The unit will be installed in the framed alcove as a one-piece unit. The unit must be installed completely level.

Alternate Connection: If installing piece by piece into the alcove, make sure that the pins are aligned correctly. When the caulking cures the parts are solidly held similar to the one piece when attached to the framing. See Photo1. The valve wall should be the first wall sections installed.

Photo 1

2. Drain and/or Overflow assembly should be installed on unit according to the manufacturer’s instructions. Apply a bead of 100% silicone caulk around the drain opening in unit before installing the fitting.

3. Locate supply lines for control valves and shower head. Measure and mark locations of fittings on the finished side of the unit. Recheck locations, and drill 1/4" pilot holes. Cut holes to final size using the appropriate size hole saw.

4. Apply wood wedges to the alcove floor. Carry unit to the opening. Align front of apron to final location and tilt unit into place. Make certain that the wood shims contact both the bathing unit and sub floor. Remove and adjust wedges if necessary to assure proper contact for support.

It is MANDATORY that these wedges are in place and in proper contact to assure structural integrity of the bathing unit.

5. Plumb and level the unit in two directions: Place a level on top of the apron, and along the finished flat area at the top of the wall. Once the unit is leveled, if any gap appears between the apron and sub floor fill the gap with solid material. When satisfied with the fit, attach the unit to framing with 6d galvanized nails or screws through the pre-drilled holes in the mounting flanges. If required, drill additional holes through the flanges in order to attach the unit to each stud.

6. Make connections to supply and drain lines. Strap all lines to the framing. Install finish trim.

Caulk as necessary.

7. Check for leaks before installing wall-board and closing off plumbing access.

8. Finish wall board as detailed in Figure 2.

www.ellasbubbles.com Page 2 03/14

Installation Procedure 2 of 3

8. Finish wall board as detailed in Figure 2.

Sectional bathing units are shipped from the factory with screws or nuts and bolts connecting the parts together.

If installing the unit fastened together in one piece, follow instructions on Page 1 of this manual.

The alignment pins should allow you to more easily install the unit in the framing alcove. Read and understand the instructions on this page since the alignment pins must be inserted in a specific direction.

1. Install drain and/or overflow assembly on unit following drain manufacturers instructions.

Place support wedges under the back edge and secure Place the base unit in the install location. Level the unit. A minimum of two shims should be used for proper support. (See

Figure 5). Re-check level and attach base to framing studs with 6D galvanized screws.

SIDE VIEW

INTEGRAL SELF-LOCATING

METAL GUIDE PINS PAN

BASE DETAIL

INTEGRAL SELF-LOCATING

METAL GUIDE PIN DETAIL

2. Place a continuous bead of silicone on base between the edge of the base and the holes.

For three and four piece units, apply silicone up the vertical seam(s) at the front or inside edge of the wall. Also around the pin alignment piece.

3. Place the walls on the top of the base aligning the holes with the pins. For three and four piece units, install the left wall first. Repeating the same for the right wall. Press all seams together to assure a tight fit. Wipe away any excess caulking. See Figure 5

4. For four piece units, install the back wall first. Install the left and right walls (Wet wall last).

Press the seams together, to assure a tight fit. Wipe away any excess caulking before it cures.

5. Make sure all seams are even and in alignment with the base section. Fasten the wall assembly to the framing using 6D galvanized screws through the mounting flanges. Fasten every 8" O.C. along the vertical flanges and to each framing stud along the top, horizontally.

www.ellasbubbles.com Page 3 03/14

USING PLASTIC FASTENERS TO STABILIZE

THE WALLS ON SECTIONAL BATHING UNITS

Sectional bathing units are shipped from the factory with screws or nuts and bolts connecting the parts together.

If installing the unit fastened together in one piece, follow instructions on Page 1 of this manual.

If you will be installing the base first then the separate wall sections, it is recommended you use the plastic fasteners. The plastic fasteners are especially usefull when installing a three or four piece bathing unit.

Using the plastic fasteners should allow you to more easily install the unit in the framing alcove. Read and understand the instructions on this page since the plastic fasteners must be inserted in a specific direction.

1.

parts into the installation area.

2.

holes on the base ledge coming in from the bottom

(outside) and pushing them upward so they point toward the ceiling. See Figure 3.

5.

the top ledge. Space evenly along the ledge. Tape them in place. They will be used to temporarily space the wall above the base while it is being placed. See Figure 4A.

Wood Blocks

Figure 4A

1/4” Bead of

Silicone Caulk

The head of the fastener and silicone should make contact with bottom ledge of the base.

Figure 4B

6.

(As shown in Figure 4B). For three and four piece units,apply silicone up the veritical seam(s) between the holes for the fasteners and the front or inside edge of the wall.

Installation Procedure 3 of 3

6. Make connections to supply and drain lines. Strap all lines to the framing. Install finish trim.

Caulk as necessary.

Silicone Bead

7.

plastic fasteners into the holes in the underside of the walls. For three piece units, install the left wall first.

Repeat for the right wall. Press all seams together to

8.

8. Finish wall board as detailed in Figure 6.

3.

wall, insert them from the backside through the holes in the vertical seam on the left wall (the wall to the left as you face the unit) so they are facing the right and the heads of them are pressed firmly to the backside of the flanges.

For four piece units, after applying the silicone to the head of the plastic fasteners for the walls, insert them on the two front vertical flanges of the back wall. These fasteners will be inserted from the backside and pressed through until the head of the fasteners fully contact the flanges. These fasteners will be pointing out towards the front of the bathing unit.

4.

Place the base unit in the install location. Level the unit.

Place support wedges under the back edge and secure with adhesive. A minimum of two shims should be used for proper support. (See Figure 5). Re-check level and attach base to framing studs with 6D galvanized screws.

Figure 5

Support Wedges

(Secure with adhesive)

2

CAUTION

If you use a RUBBER FLOOR MAT in this tub or shower unit it must be removed after each usage. If left in the unit, it may cause blisters or damage to the surface finish.

DO NOT USE ABRASIVE CLEANERS

The most important caution is to avoid use of harsh abrasive cleaners or gritty scouring powders. To clean the unit, simply use a household liquid detergent with soft sponge cloth and warm water. More persistent stains, tar, or paint can be removed with naptha or mineral spirits. Remove excess plaster by scraping with a sharpened soft wood stick. Avoid wire brushes, metal scrapers or tools. Restore dull areas by rubbing with automotive type body cleaning compound.

www.ellasbubbles.com Page 4 03/14

Limited Warranty

LIMITED WARRANTY

Ella's Bubbles, LLC warrants to the owner of its Tub/Shower units as follows: Units manufactured of fiberglass reinforced polyester resin, that it will, free of charge, repair or exchange as its option, any Ella's Bubbles unit found to be defective in materials or workmanship upon inspection by an authorized representative of Ella's Bubbles for a period of three (3) years from date of purchase.

The exchange of a unit is limited to supplying a replacement unit of comparable size and style and does not include any costs of removal or installation.

This warranty shall be voided if the unit is moved from its place of initial installation or is not installed in accordance with the instructions supplied by the manufacturer of the unit.

Further, this warranty does not apply if the unit has been subjected to accident, abuse, misuse, damage caused by flood, fire or act of God.

Since local code requirements vary greatly throughout the country, distributors, dealers, installation contractors and users of plumbing products should determine whether there are any code restrictions on the use of a specific product. Ella's Bubbles makes no representation or warranty regarding and shall not be responsible for any code compliance.

The owner agrees by use of this unit that the obligations of Ella's Bubbles shall not exceed to contingent or indirect damage or injury to the structure of its contents, that the obligations of

Ella's Bubbles are limited to those set forth herein, and that no other obligations, expressed or implied, are assumed by Ella's Bubbles.

©2014, Ella's Bubbles, LLC

2101 S. Carpenter St., Chicago, IL 60808

1.800.480.0500

www.ellasbubbles.com

www.ellasbubbles.com Page 5 03/14

9.

Make sure all seams are even and in alignment to the framing using 6D galvanized screws through the mounting flanges. Fasten every 8” O.C. along the vertical flanges and to each framing stud along the top, horizontally.

10.

11.

Make connections to supply and drain lines. Strap all lines to the framing. Install finish trim. Caulk as necessary.

Check for leaks before installing wall-board and closing off plumbing access.

12.

Finish wall board as detailed in the diagram.

Wall

Board

Shim Along

Framing

Figure 6

Caulk

Gap

Framing

Mounting

Flange

CAUTION:

If you use a RUBBER FLOOR MAT in this tub or shower unit it must be removed after each usage. If left in the unit, it may cause blisters or damage to the surface finish.

Do not use abrasive cleaners

The most important caution is to avoid use of harsh abrasive cleaners or gritty scouring powders. To clean the unit, simply use a household liquid detergent with soft sponge cloth and warm water. More persistent stains, tar, or paint can be removed with naptha or mineral spirits.

Remove excess plaster by scraping with a sharpened soft wood stick. Avoid wire brushes, metal scrapers or tools. Restore dull areas by rubbing with automotive type body cleaning compound.

Praxis Companies LLC.

435 Industrial Road

Savannah, TN. 38372

Phone: (800) 443-7269

Fax: (731) 925-7656

Model No.

G 3838 NA 2P

G 6032 TS 2P

G 3232 SH 2P

G 3635 SH 2P

G 4836 SH 2P 1S

G 3260 TS 3P

G 5494 TS 2P

G 4887 SH 3P 1S

G 3636.53

G 4834 3P 2S

Old No.

G 3838.51

G 6030.74

G 3232.50

G 3635.53

G 4835.54

N/A

N/A

N/A

6839

G 4834.50

G 6030.75

G 6036.71

G 6036.72

G 6017 TS 2P

G 4887 SH 2P 1S

G 3679 SH 3P

G 3687 SH 2P

G 3275 SH 2P

G 4080 NA 2P

6824/25

6976/77

6880/81

N/A

N/A

N/A

N/A

N/A

N/A

FRAMING DIMENSIONS

X

X

X

X

Fig 5 Fig 7 Fig 6 A

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

B C D E F G H

79”

73”

39-1/2”

60-1/4”

39-1/2”

31-7/8”

17-3/4”

14-3/4”

17-3/4” 17-3/4”

2-5/8”

74”

74”

74”

74”

32-1/4”

36-1/4”

48-1/4”

33-1/2”

36-1/2”

36-1/2”

16-1/2”

18”

18”

16”

18”

24”

60-1/4” 32-3/4” 16” N/A

74” 54-1/4” 27-1/2” 12-1/4” N/A

14-3/4”

16-1/2”

18”

18”

16”

12-1/4”

78” 48-1/4” 35-3/4” 18-1/4” 24” 18-1/4”

73”

73”

73”

36-1/4”

48-1/4”

60-1/4”

37-5/8”

35-5/8”

31-1/4”

16-1/8”

16-3/8”

14-1/2”

76” 60-1/4” 35-3/4” 15”

18”

24”

1-3/8”

2”

16-1/8”

16-3/8”

14-1/2”

15”

N/A

75”

76”

76”

76”

N/A

N/A

N/A

83-3/4”

83-3/4”

N/A

81”

82”

82”

82”

N/A

N/A

N/A

83-3/4”

83-3/4”

83-1/8” 83-1/8”

79” 82”

81” 60-1/4” 37” 17-1/2” 1-5/8” 17-1/2” 81-1/4” 81-1/4”

81” 60-1/4” 37-3/4” 16”

78” 48-1/4” 35-3/4” 18-1/4”

N/A

24”

16” N/A

18-1/4” N/A

N/A

N/A

78” 36-1/4” 37” 19” 18” 19” N/A N/A

79” 36-1/4” 36-1/4” 17-1/2”

77” 32” 34” 19-1/2”

18”

16”

17-1/2”

19-1/2”

N/A

N/A

N/A

N/A

81” 41-1/4” 41-1/4” 19” 19” 19” N/A N/A

I

48”

J

27”

19”

48”

48”

48”

N/A

N/A

N/A

48”

48”

42-1/4”

22”

17-1/2” 43”

25-1/4” 38-1/4”

22” 42-1/2”

N/A N/A

N/A N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

22”

22”

N/A

N/A

N/A

22”

22”

3 www.ellasbubbles.com Page 6 03/14

Shower Diagrams

Sectional Gelcoat Tub/Showers

Required for

G 6036.72

11

1”

4

Header for

Optional

Dome F

13”

Shower Head and Fittings

Sectional Gelcoat Showers

Header for

Optional Dome

F

13” Shower Head and Fittings

Blocking

(optional)

D

C

OUTLET

B

E

Shower

J

Fittings

Spout

8

1

/2”

A

I

G

H

Figure 7

Blocking

(optional)

C

D

CL

Outlet

G 3838 2P and G 4080 2P Showers

13”

B

F Outlet and

Supply Fittings

B

E

LC

J

Shower G

H

I

Fittings

A

Figure 8

Blocking

(optional)

J

Shower

Fittings

A

I

D

C

B

E

Figure 9

LIMITED WARRANTY

Units manufactured of fiberglass reinforced polyester resin, that it will, free of charge, repair or exchange as its option, any Praxis Companies unit found to be defective in materials or workmanship upon inspection by an authorized representitive of Praxis Companies for a period of three (3) years from date of purchase. The exchange of a unit is limited to supplying a replacement unit of comparable size and style and does not include any costs of removal or installation.

This warranty shall be voided if the unit is moved from its place of initial installation or is not installed in accordance with the instructions supplied by the manufacturer of the unit. Further, this warranty does not apply if the unit has been subjected to accident, abuse, misuse, damage caused by flood, fire or act of God.

www.ellasbubbles.com there are any code restrictions on the use of a specific product. Praxis Companies makes no representation or warranty regarding and shall not be responsible for any code compliance.

Page 7 03/14

The owner agrees by use of this unit that the obligations of Praxis Companies shall not exceed to contingent or indirect damage or injury to the structure of its contents, that the obligations of Praxis Companies are limited to those set forth herin, and that no other obligations, expressed or implied, are assumed by Praxis Companies.

Contact: Praxis Companies Customer Service Department: Phone (800) 326-5489. Fax (888) 246-0466.

Spec No. 2049 REV: 12/18/06.

4

PRINTED IN U.S.A.

Ella’s Bubbles, LLC. warrants to the owner of its

ACCESSIBLE SHOWER IN A BOX as follows:

Units manufactured of fiberglass reinforced polyester resin, that it will, free of charge, repair any Ella’s unit found to be defective in material or workmanship upon inspection by an authorized representative of Ella’s for a period of thirty

(30) years from the date of purchase of the unit by a qualified professional.

The exchange of a unit is limited to supplying a replacement unit of comparable size and style and does not include any cost of removal or installation. Any component part supplied by Ella’s carries the same limited warranty provided by our supplier for a period of one (1) year. Any Ella’s product will carry a thirty (30) year limited warranty against manufacturing defects. This warranty shall be voided if the unit is moved from its place of initial installation or is not installed in accordance with the instructions supplied by the manufacturer of the unit. Further, this warranty does not apply if the unit has been subjected to accident, abuse, misuse, damage caused by flood, fire, or act of God. The owner agrees by use of the unit that the obligations of Ella’s Bubbles, LLC. shall not exceed to contingent or indirect damage or injury to the structure of its contents, that the obligations of Ella

Walk in Baths are limited to those set forth herein, and that no other obligations, expressed or implied, are assumed by Ella’s Bubbles.

All mailing notification must be sent via certified mail to:

Ella’s Bubbles, LLC.

2101 S. Carpenter Street

Chicago, IL 60608

Email: [email protected]

May 2013 TOLL FREE: 800-480-6850

Warranty Activation Form 1 of 2

INSTALLER'S INFORMATION

_______________________________________________________________________________________

Name

_______________________________________________________________________________________

Address City State Zip

_________________________________ _________________________________________________

Telephone Email

_________________________________ _________________________________________________

Date Signature

Upon completing the installation of an Ella Walk In Tub, the following Warranty

Activation Form must be completed, signed by both the customer and installer, and returned to Ella’s Bubbles, LLC. In order for the Warranty to be activated (faxed, scanned, or emailed, or hard copy mailed).

To be initialed by the installer(s)

____Tub is level in all directions and all support legs are touching the ground.

____Tub is installed on a dedicated 30 Amp GFCI protected circuit using 10 gauge wire

____Frame of the tub has been properly grounded.

____ Door Seal has been cleaning with rubbing alcohol to remove any dust or debris left over from construction.

____Temperature Control Valve operated on both hot and cold settings.

____Both diverters function properly.

____Hand Shower functions on all settings without leaking.

____All supply lines have been checked for leaks while both diverters are on.

____ Drains open and close properly, and the locking nut has been tightened on both stoppers.

____Door seal is water tight after tub has been filled for a minimum of 20 minutes.

____ After running for a minimum of 20 Minutes both the Hydro and Air Pumps are functioning properly and all connections to the pumps and jets are water tight.

____ Chromatherapy Light and the Ozone Sterilization are working properly. (When the

Ozone is on by itself it will make a light humming noise).

____All drain fittings have been checked for leaks while the tub is draining.

____Unit is installed with access to both plumbing and electrical connections. www.ellasbubbles.com Page 23 03/14

Warranty Activation Form 2 of 2

OWNER'S INFORMATION

_______________________________________________________________________________________

Name

_______________________________________________________________________________________

Address City State Zip

_________________________________ _________________________________________________

Telephone Email

_________________________________ _________________________________________________

Date Signature

Model: ___________________________________ Serial Number: ______________________________

Purchase Date: ___________________________ Purchase Price: _____________________________

Place of Purchase: _____________________________________________________________________

Contact Name: ___________________________ Phone Number: _____________________________

Copy of sales receipt must be included with warranty activation forms.

To activate manufacturer's warranty, please complete both pages and use one of the options below to submit.

Via mail: Ella's Bubbles, LLC.

Warranty Department

2101 S. Carpenter St., Chicago, IL 60608

Via fax: 1-312-666-3551

Via email: [email protected]

www.ellasbubbles.com Page 24 03/14