advertisement
HW-390M
User manual guide for 2.4G
Wireles
HW-390M
(Work with X BOX 360/PS3/WII/ PC/ MAC/TV)
Features
1.The HW-390M is a 2.4Ghz wireless headset, specially designed
for use with X BOX 360 and PS3. The transmitter has a built-in
Microsoft approved non-driver USB sound card and adopts a
pure-digit decoding system. You can hear both game sounds
and the chat through headset courtesy of the special circuit
design and in built amplifier. Hear chat in real-time overlayed
with stereo game sounds. Use volume buttons on the headset
to adjust the volume..
2. Digital wireless technology allows you to operate the
headphones at a distance of up to 10 meters from the
transmitter – allowing you freedom to move around without
wires while playing games. The headset can be used for up to 8
hours between charges.
3. The headphones fit snugly over your ears sealing in sounds so
you can play games at reasonable volumes without disturbing
those nearby. High quality 40mm drivers deliver crystal clear
sound quality and allow even low volume sounds to be heard
during game play giving great advantage to the serious game
player.
4. The headphones can also be used with WII, PC,MAC, and TV,
for good stereo sound effects while playing games, watching
movies and listening to music. It is plug-and-play and fully
supports USB2.,
5. The microphone is detachable, and can be removed if not being
used..
Interfaces:
Transmitter:
1. 3.5mm audio input
2. Mini USB port
3. Working indicator light
A. The left part of headset
1. 3.5mm microphone interface
2. 3.5mm XBOX360 interface.
3.Working indicator light
4.Volume+ / Volume_ buttons
5. MIC mute button
B. The right part of headset
1. Power on/off button
2. USB recharging port
3. Recharging indicator light.
Connections:
1. Connect with PC: use the USB cable to connect the transmitter
with PC as pictured below:
2. Connect with PS3: Use RCA cable to connect with TV and
transmitter: plug 3.5mm jack into 3.5mm hole of the transmitter,
the white/red RCA plugs are connected with the corresponding
interface of TV; Use the USB cable to connect with the
transmitter and USB port of PS3 as pictured below:
3. Connect with X BOX 360: Use RCA cable to connect with TV and
transmitter: plug 3.5mm jack into 3.5mm hole of the transmitter,
the white/red RCA plugs are connected with the corresponding
interface of TV; Use the USB cable to connect with the transmitter
and USB port of XBOX360; Use the 2.5-3.5mm cable to connect
the headset with the controller of XBOX360, 3.5mm plug
connected with headset, 2.5mm plug connected with the controller
of the XBOX360 as pictured below:
Operation:
1. Use USB cable to connect the transmitter with the port of USB
device such as PC, PS3, XBOX360, the working indicator light will
be flashing.
2. Push the power toggle button on the right of headset to "on"
position to power on the headset. If the headset and transmitter
was paired successfully, the LED lights for both headset and
transmitter will stop flashing; otherwise, the LED lights continue
flashing.
3. How to pair the headset and transmitter: when you need to pair
the headset and transmitter, please close the all applications on
your PC, or exit MIC mode if using a PS3; please keep within 50
CM between the headset and the transmitter, press the MIC "Mute"
button on the left earlap for 5 seconds to enter pairing mode, when
the LED light on the left earlap of the headset is quickly flashing,
release the button, after 5-10 seconds, the LED light stops flashing
and stop flashing. This means the pairing is successful. When
pairing is finished, don't press any keys wait for 6 seconds,power
off the headset and then power it on again, the headset will auto
pair with the transmitter and also auto save the
pairing settings in the memory..
4. On the left side of the headset, there are MIC
mute button, game sounds and chat sounds
adjustment buttons available. Press these
buttons to adjust the volume. When MIC is on,
press the mute button to mute the mic, press
the button again to turn off mute. When you
press and hold the game or chat volume button,
it will go to the maximum or minimum level
respectively. The last operation memory will
be saved after you power off the Headset.
Precautions:
1.If the battery is depleted no LED will be shown when you attempt to
power on. Charge the headset using the USB charging cable and
continue charging until the red LED is no longer displayed. Charge
time is approximately 3 hours..
2.The headset will be paired to the transmitter as default using
factory settings. If you need to re-pair the headset hold down the
Mic Mute button until the LED flashes quickly. Once paired the LED
will stop flashing. Wait for 6 seconds and power off the headset.
Then power on and it will auto pair with the transmitter and save
the pair to memory.
3. Low battery warning: when the voltage of the built-in battery is
low, the LED light on the left side of headset will flash for 1 second,
to remind you that the battery strength is low.
4. When you use the headset for PC/MAC, the game volume+,
volume- cannot be used. Control volumes using the PC or Mac
operating system.
5. When you use headset for WII/TV as an amplified headset,the
chat Volume buttons will be disabled.
6. If no sound is heard on the headset – check all connections and
also try pressing the volume buttons to increase the volume.
7. PC Trouble Shooting: Right click the speaker icon at the right
down of PC screen by using the mouse, select "Adjust Audio
Properties / volume / Sound
playback default device /
2.4G WIRELESS HEADSET
AND RECORD/2.4G WIRELESS
HEADSET. After tick "default
device only", click "apply/
confirm" to exit. Restart the
PC with the headset connected.
Packaging contents:
1. Transmitter-----------------------1PCS
2. Wireless headset------------------1PCS
3. RCA-3.5 cable----------------------1PCS
4. USB-USB mini cable---------------1PCS
5. 3.5-2.5 cable------------------------1PCS
(USB 2.0)
6. Detachable Microphone-----------1PCS
7. Manual guide------------------------1PCS
Specifications:
Transmitter:
Dimensions: 86x65x20mm
Weight: 28g(not include the cable)
Working voltage: 5V
Working current: 50mA
Frequency range: 2.40
2-2.480GHz
Frequency space:
1MHz
Transmit rate:
5 dBm
Receiving/transmit distance: ≥ 10M , 360°
Receiving sensitivity: -80dBm
Headset :
Max Dimensions: 205x160x80mm
Weight: 162g
(not include MIC and connection cable)
Working voltage: 3.
7V
Working current: 50 mA
Lithium battery:
660 mAh
Working hours: 8h
Charging time: ≈3h
Frequency range: 2.40
2-2.480GHz
Frequency space:
1MHz
Transmit rate: 3dBm
°
Sampling frequency: 32KHz,16bit
Modulate mode: GFSK
Receiving sensitivity:-80dBm
°
SNR: 75dB
Speaker size: Ф40mm
Speaker impedance: 32Ω
Frequency response: 20~20KHz
Microphone sizes: 6*5mm
Microphone sensitivity: -58dB
Microphone direction: Omni directional
Microphone frequency response: 100Hz-8KHz
USB-USB mini cable length: 1.2m
RCA-3.5 connection cable: 1m
2.5-3.5 connection cable: 0.8m
7
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
.
..
.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition
without restriction.
ollowing measures:
advertisement