Assembly Instructions
Important
Before you begin, please make sure all parts and proper quantities are included. Any parts damaged during shipment must be reported within 15 days of receipt. To report information regarding damage, to purchase parts or accessories, or if you have any questions, please contact us at: www.spectrumfurniture.com
715-723-6750, 800-235-1262
Thank you for purchasing Spectrum products!
(1) worksurface
(2) leg
(1) chair rail
(1) cord channel / modesty panel
026011
1/4-20 x 2” FHMS
(2) 36”
(3) 60”, 72”
(10) 1/4-20 x 5/8” PHMS
026064 (black) or 043493 (putty)
(10) 36”
(12) 60”, 72”
(4) 041289
1/4-20 x 1-3/4” PHMS
052463 unit-to-unit bracket
(2) 36”
(1) 60”, 72”
(4) 025068
5/16-18 x 1” glide
(1) 025069 glide wrench
1. Attach legs to worksurface
1. Place the worksurface face-down onto a non-abrasive surface.
2. Align the legs with the mounting holes, and install 1/4-20 x 1-3/4” PHM screws into the legs as shown. Figure 1A.
3. Install 1/4-20 x 1-3/4” PHM screws into the legs as shown, but do not tighten the screws completely yet.
For 60” & 72” desks only:
Orient and attach the chair rail bracket to the center of the worksurface as shown in Figure 1B with (2) 1/4-20 x 5/8” PHM screws.
1/4-20 x 5/8” PHMS
(2 required)
Evolution Desk 30”D
38901 - 36”W
38904 - 60”W
38905 - 72”W
38901ADJ - 36”W
38904ADJ - 60”W
38905ADJ - 72”W
(for 60”, and 72” desks only)
Phillips screwdriver
(1) 051024
Chair rail bracket glide wrench
(1) 036281
Dual unit-to-unit bracket
The side of the leg without the end cap should be on the worksurface flip-top side flip-top
1/4-20 x
1-3/4” PHMS
(4 required) worksurface chair rail bracket flip-top worksurface
Figure 1B
The legs should be attached with the side panels flush with the legs.
Figure 1A
052519R2 Page 1 of 4
2. Install cord channel / modesty panel and glides
1. Orient the modesty panel/cord channel as shown and attach to the legs with (4) 1/4-20 x 5/8” PHM screws. Figure 2A.
Note: If you are assembling a 60, or 72” desk, slide the cord channel over the chair rail bracket. The bracket will support the inside of the cord channel. Figure 2B.
glides
(4 required)
2. Install the (4) glides to the bottom of the legs. The glides can be adjusted later to keep the desk level on uneven surfaces.
3. Tighten ALL screws.
cord channel chair rail bracket
Figure 2B
Adjustable legs
If you have a desk with the adjustable leg feature, the worksurface height can be adjusted from
24”H - 32”H in 1” increments. Figure 2C. Adjustment is easier if the desk is upside-down.
1. To adjust the legs, remove the (4) pre-installed adjustment screws.
(Fully-support the lower section of the leg while removing). Figure 2D.
2. Choose a height and align the corresponding set of leg holes.
3. Install the (4) previously removed screws in the new holes and tighten securely.
4. Repeat this procedure on the second leg. Make sure to use the same set of holes used on the first leg.
up to 8” of adjustment adjustment screws
1/4-20 x 5/8” PHMS
(4 required) modesty panel / cord channel
Figure 2A lower section up to 8” of adjustment
Figure 2C Figure 2D
052519R2 Page 2 of 4
3. Attach chair rail
1. Carefully stand the desk upright-this will require at least two people.
2. Attach the chair rail with (2) 1/4-20 x 2” FHM screws as shown. Figure 3.
The chair rail should extend above the worksurface, and the countersunk holes should be on the outside.
Note: If you are assembling a 60 or 72” desk, attach the center of the chair rail to the chair rail bracket using the 3rd flat head screw.
(The chair rail bracket may require slight adjustment to align properly.)
3. Tighten all screws securely.
chair rail
1/4-20 x 2” FHMS
(2 required)
60” and 72” desks only
Figure 3
4. Attaching desks together (optional)
Two desks can be attached together with (2) of the included unit-to-unit brackets.
1. Locate the desks next to each other in their final position.
2. Attach one of the narrow unit-to-unit brackets to the rear of the legs using the existing leg screws
(loosen leg screws to install, then re-tighten).
3. For 36” desks, attach a second narrow bracket to the front of the legs using the existing leg screws.
For 60” and 72” desks, attach the dual unit-to-unit bracket to both worksurfaces using (4) 1/4-20 x
5/8” PHM screws.
4. Tighten all screws securely.
36”W desks 60”, 72”W desks
desk #2 narrow unit-to-unit brackets
(loosen screws to install, then re-tighten) desk #2 narrow unit-to-unit bracket
(loosen screws to install, then re-tighten) desk #1 desk #1 dual unit-to-unit bracket
(attach with 1/4-20 x 5/8”
PHM screws)
Figure 4A Figure 4B
052519R2 Page 3 of 4
Warranty Statement
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products is manufactured from the best materials available and each product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below from the date of delivery. This warranty shall not apply to defects or damage resulting from misuse, abuse, neglect, improper care, modification or repair not authorized by Spectrum, or any other cause outside the control of Spectrum. Spectrum will, at its sole option, either repair or replace the defective product.
This warranty is exclusive; no other warranty, written or oral, is expressed or implied. This warranty is given by Spectrum to Buyer and to no other person or legal entity. No Spectrum dealer, distributor, agent or employee is authorized to make any modification or addition to this warranty.
NOTWITHSTANDING ANYTHING TO THE CONTRARY, SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR
LIQUIDATED DAMAGES, INCLUDING CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES. IN NO EVENT SHALL SPECTRUM’S LIABIL-
ITY, WHETHER UNDER CONTRACT OR WARRANTY, IN TORT OR OTHERWISE, EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM
FOR THE PRODUCT AT ISSUE AND “RECALL ACTION” EXPENSES. SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS
OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABIL-
ITY) OR OTHER THEORIES OF LAW, WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM, OR ANY UNDERTAK-
INGS, ACTS OR OMISSIONS RELATING THERETO.
Our Customer Service Department is ready to provide immediate attention to any questions, comments or concerns. They are available to answer your calls
Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome via e-mail at: [email protected].
Warranty Table
Item
• Adjustable Crank/Electric Desk Legs
• Flat Panel Desk Gas Cylinders
• Adjustable Height Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles Adjustable Height Chair Parts Casters
• Adjustable Height Chair Upholstery
• In-Stock Upholstery
• Graded-In Fabrics and Customer Owned Material
• Height Adjustable Columns and Lifts
• General Use Casters
• Electrical
• Keyboard/Mouse Trays
• Flat Panel Monitor Arm – General Parts
• Flat Panel Monitor Arm – Gas Cylinders
• Computer Desk Chassis
• Cart Chassis
• Lectern Chassis
Warranty Period
• 1 Year
• 7 Years
• 2 Years
• 2 Years
• No Warranty
• 1 Year
• 5 Years
• 2 Years
• 10 Years
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 800-235-1262, 715-723-6750 Fax: 800-335-0473, 715-738-2309
E-mail: [email protected] web: www.spectrumfurniture.com
052519R2 Page 4 of 4
