OEM UM 990-3713 MN01 EN.fm

Installation and Operation
Smart-UPS®
oem0141a
External Battery Pack
Tower/Rack-Mount 2U/3U
SRC192XLBP
SRC240XLBP1
SRC240XLBP2
Smart-UPS®
External Battery Pack
Tower/Rack-Mount 2U/3U
SRC192XLBP
SRC240XLBP1
SRC240XLBP2
English
Overview
The APC® by Schneider Electric Smart-UPS® SRC 5/6/8/10 kVA is a high performance uninterruptible
power supply (UPS). It provides protection for electronic equipment from utility power blackouts,
brownouts, sags, and surges; small utility fluctuations and large disturbances. The UPS also provides
battery backup power until utility power returns to safe levels or the batteries are fully discharged.
Safety
Read the Safety Guide included in the package before installing the UPS.
Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.
Recycle the packaging.
Inventory
SRC192XLBP
(12)
(6)
(1 pair)
(2)
(1 pair)
(2)
SRC240XLBP1/SRC240XLBP2
(12)
(12)
All models
(1)
(1 User Manual)
2
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
Specifications
Temperature
Maximum
Elevation
Humidity
This unit is intended for indoor use only.
Select a location sturdy enough to handle
the weight.
Operating
0° to 40° C (32° to 104° F)
Storage
-15° to 45° C (5° to 113° F)
charge UPS battery every six months
Operating
3,000 m (10,000 ft)
Do not operate UPS where there is
excessive dust or temperature or humidity
are outside specified limits.
Storage
15,000 m (50,000 ft)
This unit has air vents. Allow adequate
space for proper ventilation.
Environmental factors impact battery life.
High temperatures, poor utility power, and
frequent, short duration discharges will
shorten battery life.
0% to 95% relative humidity, non-condensing
Installation
Tower Configuration
oem0077a
oem0076a
Install stabilizer brackets
x4
x4
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
3
Connect External Battery Packs to UPS
Battery safety
Read and adhere to all safety warnings when the external battery packs are installed.
Failure to observe these warnings may result in serious injury, death or damage to the equipment.
• Do not attempt to install the external battery packs.
• A qualified electrician should perform the installation of the external battery packs.
• Always wear:
Goggles or face shields
Acid-resistant, insulated gloves
Protective aprons
Protective overshoes or rubber boots
Practices
• Always Use:
Insulated tools
Rubber mats to cover batteries during servicing
Rubber mats or rubber stands on the floor
Adequate lifting devices
• Remove: watches, rings, and other metal objects from your body
• Do not lay tools or metal parts on top of battery packs.
• Lead-acid batteries contain hazardous, toxic materials.
Precautions Do not open, alter or mutilate battery packs. Internal materials may be harmful to the skin and
eyes.
Do not dispose of batteries in a fire. There is danger of explosion.
• Handle, transport and recycle batteries in accordance with local codes and regulations.
4
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
Installation
oem0085a
SRC192XLBP
oem0083a
SRC240XLBP1/SRC240XLBP2
1. Set the circuit breaker switch on the rear panel of
external battery pack to the OFF position.
2. Remove battery connector cover on both the UPS and
the battery pack. Keep the screws.
3. Plug the XLBP cable into the UPS external battery
pack receptacle.
4. Secure the cable on the UPS and the battery pack
with the screws removed in step 2.
Oem0070a
5. Set the circuit breaker switch on the rear panel of the
battery pack to the ON position.
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
5
Configure UPS Parameters
This configuration affects the accuracy of the predicted runtime calculations the UPS performs
while running on battery power.
Refer to the Battery String Configuration tables at the end of this section for detailed instructions.
Smart-UPS RC models must be programed to recognize the number of battery strings connected to the UPS.
There are four options available for configuring the UPS to recognize the number of battery strings
1. UPS terminal mode
2. UPS display interface
Configure UPS connection settings using UPS terminal mode
Connect the serial cable to the serial port on the back of the UPS. If using USB communication to the UPS,
disconnect USB cable prior to connecting serial cable.
1. Open a terminal program, such as HyperTerminal
From the Desktop, go to: Start, Programs, Accessories, Communication, HyperTerminal
2. Follow the prompts to choose a name and select an icon. Disregard the message, "...must install a
modem," if it is displayed. Click Cancel
3. Go to File, Properties. Select the COM port that is connected to your UPS. The port settings are:
– bits per second - 2400
– data - bits 8
– parity - none
– stop bit - 1
– flow control - none
4. Click OK in each of two windows
5. Press ENTER
Configure the number of battery strings through the display interface menus
1. Press the Enter key into the main menu.
Main Menu
Status
2. Scroll down to configuration.
Main Menu
Configuration
3. Press the enter key into the menu of configuration.
Language
English
4. Scroll down to battery setup by number of battery pack.
Ext Battery
Packs: 0
5. Select the correct number of battery pack.
6
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
Configure the number of battery strings using UPS terminal mode
1. Once the blank terminal window is open, follow these steps to enter the number of battery strings:
NOTE: Letter key commands are case sensitive. Use capital letters when using letter key commands.
2. Press Y. The UPS will respond with SM in the command box. If the UPS does not respond to the
Y command, ensure the serial cable is securely connected to the serial port on the UPS. Use only
an APC supplied serial cable.
3. When SM appears in the command box press the > key. The UPS will respond with the number
of battery strings connected to the UPS. If the UPS has not been previously programmed to
recognize the number of battery strings this number will be 1.
4. Use the + or - keys to change the number of battery strings. OK will appear in the command box.
5. Press > key. The number of battery strings will appear in the command box.
NOTE: The + or - keys and the > key must be used again to change the number of battery strings
from this point in the programming.
6. Press R. The UPS will respond with BYE in the command box.
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
7
Battery configuration tables
Smart-UPS XLICH Models - Configure the Number of Battery Packs. Each battery pack consists
of one 192 V or one 240 V battery module.
Count the number of battery packs being used and enter that number.
Configuration
# of Battery
Packs
Factory Default
UPS with 1 external battery pack
1
SRC192XLBP
5000 VA/6000 VA
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
UPS with 4 external battery packs
4
UPS with 1 external battery pack
1
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
UPS with 4 external battery packs
4
UPS with 1 external battery pack
1
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
UPS with 4 external battery packs
4
SRC240XLBP1
8000 VA
SRC240XLBP2
10000 VA
Smart-UPS UXI/UXICH Models - Configure the Number of Battery Packs. Each battery pack consists
of one 192 V or one 240 V battery module.
Count the number of battery packs being used and enter that number.
Configuration
# of Battery
Packs
Factory Default
UPS with 1 external battery pack
1
SRC192XLBP
5000 VA/6000 VA
UPS with 1 external battery pack
1
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
UPS with 1 external battery pack
1
UPS with 1 external battery pack
1
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
UPS with 1 external battery pack
1
UPS with 1 external battery pack
1
UPS with 2 external battery packs
2
UPS with 3 external battery packs
3
SRC240XLBP1
8000 VA
SRC240XLBP2
10000 VA
8
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
Maintenance, Transport and Service
Battery Replacement
The external battery packs do not have user replaceable battery modules. Contact APC at www.apc.com
to order replacement external battery packs.
Once the battery packs have been disconnected the connected equipment is not
protected from power outages.
When the battery packs have been replaced the LED on the display interface will prompt the
user to enter a new battery replacement date.
Return spent batteries to an appropriate facility for proper disposal and recycling.
Prepare the UPS for Transport
1. Disconnect the UPS from all external battery packs.
2. Shut down and disconnect all equipment connected to the UPS.
3. Shut down and disconnect the UPS from utility power.
4. Follow shipping instructions outlined in “Service” on page 9 in this manual.
Service
If the UPS requires service do not return it to the dealer. Follow these steps:
1. Review the problems discussed in the Troubleshooting section of the UPS manual to eliminate
common problems.
2. If the problem persists, contact APC Customer Support through the
APC Web site, www.apc.com.
a. Note the model number of the UPS, the serial number located on the rear side of the unit,
and the date purchased. If you call APC Customer Support, a technician will ask you to
describe the problem and attempt to solve it over the phone. If this is not possible, the
technician will issue a Returned Material Authorization Number (RMA#).
b. If the UPS is under warranty, repairs are free.
c. Procedures for servicing or returning products may vary internationally. Refer to the APC
Web site for country specific instructions.
3. Pack the UPS in its original packaging. If this is not available, refer to www.apc.com for
information about obtaining a new set.
a. Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for
packaging. Damage sustained in transit is not covered under warranty.
b. Always DISCONNECT THE UPS BATTERY before shipping in compliance with U.S.
Department of Transportation (DOT) and IATA regulations. Mark the RMA# on the
outside of the package.
4. Return the UPS by insured, prepaid carrier to the address given to you by Customer Support.
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
9
Contact Information
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the
following ways:
• Refer to the APC Web site to access documents in the APC Knowledge Base and to submit
customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
– www.apc.com
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
Local, country-specific centers:
go to www.apc.com for information.
Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.
10
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
One-Year Factory Warranty
The limited warranty provided by American Power Conversion (APC®) in this statement of Limited Factory Warranty
applies only to products you purchase for your commercial or industrial use in the ordinary course of your business.
Terms of warranty
APC warrants its products to be free from defects in materials and workmanship for a period of one year from the date of
purchase. The obligation of APC under this warranty is limited to repairing or replacing, at its sole discretion, any such
defective products. This warranty does not apply to equipment that has been damaged by accident, negligence or
misapplication or has been altered or modified in any way. Repair or replacement of a defective product or part thereof
does not extend the original warranty period. Any parts furnished under this warranty may be new or factoryremanufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly registered the product. The product may be
registered at the APC Web site, www.apc.com.
Exclusions
APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product
does not exist or was caused by end user or any third person misuse, negligence, improper installation or testing. Further,
APC shall not be liable under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical
voltage or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation, start-up by
non-APC designated personnel, a change in location or operating use, exposure to the elements, Acts of God, fire, theft,
or installation contrary to APC recommendations or specifications or in any event if the APC serial number has been
altered, defaced, or removed, or any other cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF
PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION
HEREWITH. APC DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND
FITNESS FOR A PARTICULAR PURPOSE. APC EXPRESS WARRANTIES WILL NOT BE ENLARGED,
DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, APC
RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS.
THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE
LIABILITY AND PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC
WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY
FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE,
SERVICE OR INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR
TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN
ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, APC IS NOT LIABLE
FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF
EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS, CLAIMS BY THIRD
PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF
THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN
APC OFFICER AND LEGAL DEPARTMENT.
Warranty claims
Customers with warranty claims issues may access the APC customer support network through the Support page of the
APC Web site, www.apc.com/support. Select your country from the country selection pull-down menu. Open the Support
tab at the top of the Web page to obtain contact information for customer support in your region.
© 2009 APC by Schneider Electric. APC, the APC logo, and Smart-UPS are owned by Schneider Electric Industries S.A.S., American Power
Conversion Corporation, or their affiliated companies. All other trademarks are property of their respective owners.
Smart-UPS SRC192XLBP, SRC240XLBP1, and SRC240XLBP2
11
990-3713
9/2009