plumbing symbols and abbreviations

SANITARY DRAIN/SEWER (ABOVE GRADE)
SAN
SANITARY DRAIN/SEWER (BELOW GRADE)
COMPRESSED AIR
FILTER/WATER SEPARATOR
PRESSURE REDUCING VALVE
ST
STORM DRAIN SEWAGE (BELOW GRADE)
PNEUMATIC CONTROL VALVE (3 WAY)
SST
SECONDARY STORM DRAIN SEWAGE (ABOVE GRADE)
SOLENOID OR MOTORIZED VALVE
(E)
EXISTING PIPING TO REMAIN
SYMBOL(E)
IN-LINE PUMP (PLAN)
SOLENOID OR MOTORIZED CONTROL VALVE (3 WAY)
SANITARY VENT PIPING
GREASE WASTE (BELOW GRADE)
THE PIPING INDICATED ON THESE PLANS ARE DIAGRAMMATIC. ALL WORK
SHALL BE COORDINATED WITH ALL OTHER TRADES PRIOR TO
INSTALLATION. CONTRACTOR SHALL COORDINATE ROUTING OF ALL
PIPING WITH EXISTING CONDITIONS AND SHALL PROVIDE ANY
NECESSARY OFFSETS, REROUTING, TEES, ELBOWS, ETC. REQUIRED FOR
A COMPLETE AND COORDINATED INSTALLATION.
C.
PROVIDE ALL WORK IN COMPLIANCE WITH ALL LOCAL, STATE AND FEDERAL
CODES. OBTAIN ALL REQUIRED PERMITS.
D.
PROVIDE ALL REQUIRED EXCAVATION, BACKFILL AND COMPACTION FOR
ALL UNDERGROUND WORK.
E.
FIELD VERIFY EXACT LOCATION, DEPTH, COMPOSITION AND CONDITION OF
ALL PIPING, VALVES AND SYSTEMS AS REQUIRED FOR WORK OF THE
CONTRACT.
F.
PROVIDE CUTTING, CORING AND PATCHING OF ALL WALLS, SLABS AND
DECKS AS REQUIRED FOR WORK SHOWN. COORDINATE ALL WORK WITH
OWNER AND GENERAL CONTRACTOR AND ALL TRADES.
G.
PROVIDE SCHEDULE 40 BLACK STEEL PIPE SLEEVES FOR ALL
UNDERGROUND PIPING PASSING THROUGH OR UNDER FOOTINGS, WALLS,
FOUNDATION WALLS, SLABS FLOORS AND/OR UNDERGROUND
STRUCTURES. REFER TO THE PROJECT SPECIFICATIONS FOR ADDITIONAL
REQUIREMENTS.
H.
WHERE PIPING IS LOCATED OVER FOOTINGS AND/OR OTHER
UNDERGROUND STRUCTURES, ROLL DOWN AS REQUIRED TO CONNECT
TO SYSTEMS NOTED. PROVIDE ALL REQUIRED OFFSETS, FITTINGS AND
CONNECTIONS.
PUMP (SCHEMATIC)
SECONDARY STORM DRAIN SEWAGE (BELOW GRADE)
GW
3.)
IF REQUIRED, PROVIDE SHUT DOWNS AND TIE-INS DURING OFF HOURS
TO AVOID DISRUPTION OF BUILDING SYSTEMS. COORDINATE ALL SHUT
DOWN REQUIREMENTS PRIOR TO SUBMITTING BID (INCLUDE ALL
REQUIRED DURING OFF HOURS IN BID).
STEAM TRAP
STORM DRAIN SEWAGE (ABOVE GRADE)
V
B.
PNEUMATIC VALVE
ST
SST
THE EXISTING PIPING INDICATED ON THESE PLANS SHALL BE
VERIFIED IN THE FIELD FOR EXACT LOCATIONS, QUANTITY, AND PIPE
SIZES.
FLEX CONNECTION
TRIPLE DUTY VALVE
EXPANSION JOINT WITH
GUIDES
RELIEF VALVE
EXISTING PIPING TO BE REMOVED
4.)
THE CONTRACTOR SHALL OBTAIN AND PAY ALL FEES RELATED TO
PERMITTING, INSPECTIONS, TAP-ON FEES, ETC.
5.)
CONTRACTOR SHALL COORDINATE ANY PLUMBING OR PIPING SYSTEM
SHUTDOWN WITH THE OWNER 48 HOURS IN ADVANCE.
6.)
CONTRACTOR SHALL COORDINATE AND PROVIDE ALL NECESSARY PIPING
& PLUMBING FITTINGS, PIPING, MISCELLANEOUS ITEMS REQUIRED FOR
A COMPLETE INSTALLATION OF ALL PLUMBING RELATED ITEMS.
7.)
ALL WORK SHALL BE COORDINATED WITH THE EQUIPMENT VENDORS.
PIPE ANCHOR
PIPE TURNED UP
TEMPERATURE & PRESSURE RELIEF VALVE
PIPE TURNED DOWN
HOSE BIBB OR DRAIN VALVE
BRANCH OFF BOTTOM OF PIPE
PIPE GUIDE
CWS WALL HYDRANT
EQUIPMENT TO BE REMOVED
NON-FREEZE CWS & HWS WALL HYDRANT IN BOX
REDUCER
NON-FREEZE ROOF HYDRANT
PIPE BREAK
PIPE CONTINUATION
NEW CONNECTION TO EXIST.
UNION
BUTTERFLY VALVE
FLANGE
GATE VALVE - NRS
GATE VALVE - OS&Y
PRESSURE GAUGE
GLOBE VALVE
THERMOMETER
REMOVE TO THIS POINT
X
PLUG VALVE
1
WATER HAMMER ARRESTER
SHUT-OFF VALVE (GATE, BALL,
OR BUTTERFLY - REFER TO SPECS)
3
11.)
THE PLUMBING SYSTEM SHALL BE TESTED AS REQUIRED BY STATE AND LOCAL
CODE OR BY THE REQUIREMENTS OF THE LOCAL PLUMBING INSPECTOR.
L.
THE ENTIRE DOMESTIC WATER SYSTEM (EXISTING/NEW) SHALL BE
DISINFECTED IN ACCORDANCE TO THE LOCAL CODE & HEALTH
DEPARTMENT REQUIREMENTS.
M.
PROVIDE BARRIER TYPE SEAL DEVICE ON ALL FLOOR DRAINS.
N.
REFER TO ARCHITECTURAL DRAWINGS AND THE PROJECT SPECIFICATIONS
FOR ANY PROJECT PHASING REQUIREMENTS.
12.)
13.)
THE BACKFLOW PREVENTION DEVICE SHALL BE INSTALLED PER STATE AND
LOCAL CODE & PER AUTHORITY HAVING JURISDICTION REQUIREMENTS.
14.)
THE CONTRACTOR SHALL NOT SCALE THESE DRAWINGS.
DEMOLITION KEYNOTE
℄
CLG
CO
CONN
CWS
COND
DB
DEG
DF
DIA
DN
DPCO
DRS
DW
DWG
DWH
(E)
EA
ELEV
ENT
EQ
EQUIP
EQUIV
ETR
°F
FAI
FCO
FD
FIN
FL
FLA
FPWH
FT
GA
GALV
GC
GPD
GPH
GPM
GW
HT
HB
HD
HP
HR
HTR
HWS
HWR
ID
INCL
INV
K
KW
LAV
MC
MED
MFR
MISC
MIN
MSS
MTD
(N)
NC
NH
No
NO
NTS
OD
ODWH
OPG
OS
OT
OZ
PART
PDR
PERF
PH
PIV
POS
PRESS
PS
PSI
PSIG
NEW
NORMALLY CLOSED
NO HUB
NUMBER
NORMALLY OPEN
NOT TO SCALE
OUTSIDE DIMENSION
ON DEMAND WATER HEATER
OPENING
OPEN SITE
OFF TOP
OUNCE
PARTIAL
PLENUM DRAIN
PERFORATED
PHASE
POST INDICATOR VALVE
POSITIVE
PRESSURE
PRESSURE SWITCH
POUNDS PER SQUARE INCH
POUNDS PER SQUARE
INCH GAUGE
PSIA
POUNDS PER SQUARE
INCH ABSOLUTE
PT
PRESSURE TRANSMITTER
PV
PLUG VALVE
PVC
POLYVINYL CHLORIDE
PVS
POLYVINYL COATED STEEL
QUAN QUANTITY
RD
ROOF DRAIN
REL
RELIEF
REQD REQUIRED
RL
RAIN LEADER
RM
ROOM
RP
RECIRCULATION PUMP
RPM
REVOLUTIONS PER MINUTE
SA
SHOCK ABSORBER
SCH
SCHEDULE
SCHEM SCHEMATIC
SK
STAINLESS STEEL SINK
SPEC SPECIFICATION
SPS
SUMP PUMP SYSTEM
SQ
SQUARE
S/S
SERVICE SINK
SS
STAINLESS STEEL
ST
STORM
SST
SECONDARY STORM
STD
STANDARD
STL
STEEL
STR
STRUCTURAL
SUP
SUPPLY
SYS
SYSTEM
S/SHO SAFETY SHOWER
TYP
TYPICAL
UR
URINAL
VB
VACUUM BREAKER
VS
VIVARIUM SINK
VTR
VENT THRU ROOF
W
WIDTH
W/
WITH
WHA
WATER HAMMER ARRESTER
W/O
WITHOUT
WC
WATER CLOSET
WM
WATER METER
YCO
YARD CLEAN OUT
G INEER
AR
ES
C
CERT. NO.
52904
NO
CH
G S. BL YT
AS S O CI AT
I TE C TUR A
CH
L
AR
RT
H CAROLI
NA
L OT TE , N .
C
9/9/2016
© 2016 LaBella Associates
TOWN OF DAVIDSON
216 South Main Street,
Davidson, NC 28036
WASHER BOX
PLUMBING SPECIFICATION NOTES
ABBREVIATIONS
ABOVE FINISHED FLOOR
ACCESS PANEL
BACK FLOW PREVENTER
BUILDING
BASEMENT
COMPRESSED AIR
CUBIC FEET PER HOUR
CAST IRON
CENTER LINE
CEILING
CLEAN OUT
CONNECTION
COLD WATER SUPPLY
CONDUCTOR
DRAIN BOX
DEGREE
DRINKING FOUNTAIN
DIAMETER
DOWN
DECK PLATE CLEAN OUT
DARK ROOM DOUBLE BOWL SINK
DOMESTIC WATER
DRAWING
DOMESTIC WATER HEATER
EXISTING
EACH
ELEVATION
ENTERING
EQUAL
EQUIPMENT
EQUIVALENT
EXISTING TO REMAIN
DEGREES FAHRENHEIT
FRESH AIR INTAKE
FLOOR CLEANOUT
FLOOR DRAIN
FINISHED
FLOOR
FULL LOAD AMPS
FREEZE PROOF WALL HYDRANT
FEET
GAUGE
GALVANIZED
GENERAL CONTRACTOR
GALLONS PER DAY
GALLONS PER HOUR
GALLONS PER MINUTE
GREASE WASTE
HEIGHT
HOSE BIBB
HEAD (SEE SCHEDULES)
HORSE POWER
HOSE REEL
HEATER
HOT WATER SUPPLY
HOT WATER RETURN
INTERNAL DIAMETER
INCLUDING
INVERT
TYPE OF COPPER TUBING
KILOWATT
LAVATORY
MECHANICAL CONTRACTOR
MEDIUM
MANUFACTURER
MISCELLANEOUS
MINIMUM
MOP SERVICE SINK
MOUNTED
AI
LA
WB
P-TRAP
AFF
AP
BFP
BLDG
BSMT
CA
CFH
CI
PROVIDE SINGLE HOSE BIBB WITH VACUUM BREAKER (HB) UNDER
LAVATORY(S) IN ALL TOILET ROOMS WITH FLOOR DRAINS. ONE REQUIRED
PER ROOM.
ALL PIPING PENETRATIONS THROUGH NEW, EXISTING WALL, OR FLOOR
SHALL BE SEALED TO EQUAL THE RATING OF THE NEW, EXISTING
WALL OR FLOOR.
KEYNOTE
X
WHA
COORDINATE ALL VENT TERMINATIONS ABOVE ROOF WITH HVAC
CONTRACTOR. ALL VENT TERMINATIONS ABOVE ROOF SHALL BE A
MINIMUM 25'-0" AWAY FROM ANY HVAC OUTSIDE AIR INTAKE (ROOFTOP
UNIT, LOUVER, ETC.).
10.)
STRAINER
BALL VALVE
K.
SEAL
030515
EN
CR
ALL PLUMBING & PIPING SYSTEMS SHALL BE SUPPORTED AS REQUIRED
BY THE STATE AND LOCAL CODE REQUIREMENTS AND PER MANUFACTURER'S
RECOMMENDATIONS.
E S S IO N
EL
R A TI ON
9.)
VALVE(S) IN VERTICAL PIPE
CONNECT TO SITE PIPING OUTSIDE BUILDING AS SHOWN. PROVIDE ALL
REQUIRED OFFSETS, FITTINGS AND CONNECTIONS. FIELD VERIFY EXACT
LOCATION, DEPTH AND COMPOSITION OF SITE SERVICES AND
COORDINATE ALL WORK WITH SITE CONTRACTOR.
OF
I
PO
J.
O
H C ARO L
RT
C.
CLEAN OUT
CO
NON-FREEZE CWS WALL HYDRANT IN BOX
PITCH ALL SANITARY, WASTE, AND STORM PIPING AS FOLLOWS: PIPING
3" AND SMALLER, PITCH AT 2 PERCENT (14" PER FOOT) MINIMUM, PIPING
4" AND LARGER, PITCH AT 1 PERCENT (18" PER FOOT) MINIMUM.
OR
VALVE ON VERTICAL
I.
AL
CWS & HWS WALL HYDRANT
FLOOR/DECK PLATE CLEAN OUT
(PLAN VIEW)
NC LICENSE NO. C-0430
P.
FCO/DPCO
THE CONTRACTOR SHALL COORDINATE THE INSTALLATION OF ALL
UNDER SLAB PIPING WITH EXISTING STRUCTURAL FOUNDATIONS.
UNDERGROUND UTILITY LOCATIONS SHALL BE VERIFIED PRIOR TO ANY
WORK BEING PERFORMED. CONTRACTOR SHALL REPAIR OR REPLACE ALL
PIPING NOT IN PROPER WORKING ORDER OR DAMAGED DURING
INSTALLATION OF THE NEW UNDERSLAB PIPING.
8.)
NA
BRANCH OFF TOP OF PIPE
FLOOR DRAIN OR FLOOR SINK
FD
www.labellapc.com
.
ANGLE VALVE
DOMESTIC HOT WATER RECIRCULATION
SAN
2.)
B
COMPRESSED AIR QUICK
DISCONNECT W/O CHECK
LA
BALANCING VALVE
DOMESTIC COLD WATER
DOMESTIC HOT WATER SUPPLY
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
ED
WATER SERVICE (FIRE PROTECTION ONLY)
DO NOT SHUT DOWN ANY PLUMBING, FIRE PROTECTION, NATURAL GAS,
OR RELATED SYSTEMS WITHOUT BUILDING OWNER'S PRIOR WRITTEN
APPROVAL. FOLLOW ALL OWNER REQUIREMENTS AND SHUT DOWN
PROCEDURES AS WELL AS ALL REQUIREMENTS OF THIS PROJECT.
R E GI S TE R
F
A.
E
CHECK VALVE
THE ENTIRE PLUMBING SYSTEM SHALL BE IN ACCORDANCE WITH THE
LATEST EDITION OF THE PLUMBING CODE OF NORTH CAROLINA AND
LOCAL PLUMBING INSPECTOR.
H
WATER SERVICE (DOMESTIC OR COMBINED)
1.)
COMPRESSED AIR QUICK
DISCONNECT W/ CHECK
N
W
GENERAL NOTES
GENERAL PLUMBING NOTES
PR
PLUMBING SYMBOLS
1.
SCOPE OF WORK
5.
SANITARY/STORM DRAINAGE AND VENT PIPING
7.
B. BELOW GRADE
EARTH SHALL BE EXCAVATED TO A MINIMUM DEPTH WITH AN
A. THE CONTRACTOR IS RESPONSIBLE FOR ALL WORK, MATERIALS,
EVEN SURFACE TO INSURE SOLID BEARING OF PIPE FOR ITS
A. ABOVE GRADE:
-2" AND BELOW:
AND LABOR TO SATISFY A COMPLETE WORKING SYSTEM
WHETHER SPECIFIED OR IMPLIED.
B. ALL WORK IS TO BE PERFORMED IN STRICT COMPLIANCE
WITH THE NATIONAL STANDARD PLUMBING CODE (LATEST
SCH. 40 GALV. STL. PIPE WITH SCREWED
ENTIRE LENGTH.
ENDS OR SCH. 40 PVC WITH SOLVENT
-INTERIOR:
THE PIPE SHALL BE INSTALLED (UNLESS OTHER-
JOINTS OR DWV COPPER WITH SOLDER
WISE SPECIFIED) A MINIMUM OF 4 INCHES BELOW
JOINTS. ALL SOLDER TO BE "NO LEAD"
THE BOTTOM OF THE SLAB AND SHALL NOT BE
TYPE.
IN ANY DIRECT CONTACT WITH THE CONCRETE
AT ANY POINT.
EDITION), ALL LOCAL CODES, AND ALL OTHER REGULATIONS
GOVERNING WORK OF THIS NATURE.
-3" AND ABOVE:
-EXTERIOR:
SCH. 40 PVC WITH SOLVENT JOINTS.
THE WATER PIPE SHALL HAVE A MINIMUM OF
42" OF COVER AND THE SANITARY WASTE PIPE
SHALL HAVE A MINIMUM OF 24" OF COVER.
C. THE CONTRACTOR SHALL, BEFORE SUBMITTING ANY PROPOSAL,
EXAMINE THE PROPOSED SITE AND SHALL DETERMINE FOR
HIMSELF THE CONDITIONS THAT MAY EFFECT THE WORK. NO
B. BELOW GRADE:
FIRE STATION #2
SERVICE WT. CAST IRON WITH BELL AND
ALLOWANCE SHALL BE MADE IF THE CONTRACTOR FAILS TO
SPIGOT JOINTS OR SCH. 40 PVC WITH
MAKE SUCH EXAMINATIONS.
SOLVENT JOINTS.
8.
MISCELLANEOUS
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
A. COORDINATE INSTALLATION OF ALL ROOF FLASHING AT
D. ALL EQUIPMENT AND MATERIALS SHALL BE AS SPECIFIED OR
C. PVC PIPING SHALL NOT BE USED IN AIR PLENUM CEILINGS
ROOF PENETRATION.
AND SHALL NOT CROSS FIRE RATED WALLS, CEILINGS,
"APPROVED EQUAL" BY ENGINEER OR ARCHITECT.
OR FLOORS.
2.
B. DO NOT SCALE THIS DRAWING FOR EXACT DIMENSIONS.
VERIFY ALL FIGURES, CONDITIONS, AND DIMENSIONS
PERMITS
D. DRAINAGE PIPING SHALL BE RUN AS STRAIGHT AS POSSIBLE
AT THE JOB SITE.
AND SHALL HAVE LONG TURN FITTINGS.
A. THE CONTRACTOR SHALL SECURE ALL PERMITS OR APPLICA-
C. THE PLUMBING PLANS ARE INTENDED TO BE DIAGRAMMATIC
TIONS AND PAY ANY AND ALL FEES.
3.
SHOP DRAWINGS
E. DRAINAGE PIPING 3" SIZE AND SMALLER SHALL RUN AT A
MATIC AND ARE BASED ON ONE MANUFACTURE'S EQUIP-
UNIFORM GRADE OF AT LEAST 1/4" PER FOOT, AND PIPING
MEANT. THEY ARE NOT INTENDED TO SHOW EVERY ITEM
3
09/07/16
LARGER THAN 3" SHALL BE RUN AT A GRADE OF NO LESS
IN ITS EXACT LOCATION, THE EXACT DIMENSIONS, OR ALL
2
08/15/16
THAN 1/8" PER FOOT.
THE DETAILS OF THE EQUIPMENT. THE CONTRACTOR
1
08/10/16
NO:
DATE:
SHALL VERIFY THE ACTUAL DIMENSIONS OF THE EQUIP-
A. SUBMIT MATERIAL LIST AND SHOP DRAWINGS FOR MAJOR
F. ALL VENT PIPING SHALL BE SLOPED TO DRAIN BACK TO
EQUIPMENT/FIXTURES TO THE ARCHITECT OR ENGINEER
MEANT PROPOSED TO ENSURE THAT THE EQUIPMENT WILL
FIXTURES.
FOR APPROVAL. THE CONTRACTOR SHALL SUBMIT THREE
FIT IN THE AVAILABLE SPACE.
4.
A. UNDERGROUND:
9.
ALL STUB-INS AND/OR SLAB OR WALL PENETRATION TO BE
PROVIDE TYPE "K" SOFT DRAWN COPPER
PER NATIONAL STANDARD PLUMBING CODE. ALL PIPING
TUBING WITH BRAZED CONNECTIONS.
PENETRATIONS OF BUILDING FOUNDATIONS OR FOOTINGS
SHALL BE SLEEVED.
B. ABOVE GROUND:
TESTING
DRAWN BY:
A.
REVIEWED BY:
PLUMBING SYSTEMS SHALL BE FLOW AND PRESSURE
TESTED IN ACCORDANCE WITH STANDARD PRACTICE AND
THE NATIONAL STANDARD PLUMBING CODE. CONTRACTOR
SHALL SCOPE NEW LINES AND PROVIDE REPORT WITH
VIDEO.
COPPER OR BRASS FITTINGS. ALL SOLDER
10.
7.
A. MATERIALS, EQUIPMENT AND INSTALLATION SHALL BE
A. ABOVE GRADE
ISSUED FOR:
CONSTRUCTION
ALL PIPE SHALL BE SUPPORTED FROM THE BUILDING
OF ACCEPTANCE. DEFECTS WHICH APPEAR DURING THAT
MATERIAL AND FITTINGS AS LISTED IN 'TABLE 605.4 - WATER
STRUCTURE IN A NEAT AND WORKMANLIKE MANNER.
PERIOD SHALL BE CORRECTED AT THIS CONTRACTOR'S
DISTRIBUTION PIPE' , AND 'TABLE 605.5 PIPE FITTINGS'
THE USE OF WIRE AND PERFORMED METAL TO SUPPORT
EXPENSE.
OF THE PLUMBING CODE OF NEW YORK STATE.
PIPES WILL NOT BE PERMITTED. SPACING OF PIPE SUPPORTS
SHALL BE AS SPECIFIED IN CHAPTER 8 OF THE NATIONAL
STANDARD PLUMBING CODE.
07.25.16
DRAWING NAME:
GUARANTEED FOR A PERIOD OF ONE(1) YEAR FROM DATE
CONTRACTOR MAY SUBMIT OPTIONAL CODE APPROVED
FIBERGLASS INSULATION.
BB
GUARANTEE
PIPE SUPPORTS
TO BE "NO LEAD" TYPE.
C. ALL HOT WATER PIPING TO BE INSULATED WITH 1"
PAV/DWM
DATE:
PROVIDE TYPE "L" HARD DRAWN COPPER
TUBING WITH 125 PSI SOLDER JOINTS,
DESCRIPTION:
2151374
DOMESTIC WATER SUPPLY PIPING
6.
PERMITTING COMMENTS
PROJECT NUMBER:
G. CONTRACTOR SHALL BE RESPONSIBLE FOR THE PROPER
FLASHING OF THE VENT PIPING RUN THROUGH THE ROOF.
ADDENDUM 2
REVISIONS
SETS OF SHOP DRAWINGS AND THEY SHALL BE CLEARLY
LABELED.
PERMITTING COMMENTS
B. FOR THE SAME PERIOD, THE PLUMBING CONTRACTOR
SHALL BE RESPONSIBLE FOR ANY DAMAGE TO PREMISES
PLUMBING SYMBOLS AND
ABBREVIATIONS
CAUSED BY DEFECTS IN WORKMANSHIP OR IN THE WORK
OR EQUIPMENT FURNISHED AND/OR INSTALLED BY HIM.
D. ALL COLD WATER PIPING TO BE INSULATED WITH 1/2"
FOAM INSULATION.
E. COMPLY WITH NSF 14 FOR PLASTIC, POTABLE DOMESTIC WATER
DRAWING NUMBER:
MECKLENBURG
PIPING
AND COMPONENTS. COUNTY
INCLUDING MARKING "NSF-pw" ON PIPING.
CODE ENFORCEMENT
F. The
COMPLY
WITH NSF
61 FOR POTABLE
DOMESTIC WATER
Design
In These
Construction
PIPING AND COMPONENTS.
Documents
Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-001
SH-1
4"SAN
LI-1
4"SAN
3
4"SAN
FCO
4"OW
MSB-1
FD
5
4
17
4
BEDROOM
110
2"V
13
VESTIBULE
117
4"OW
4"SAN
WB
LAUNDRY
116
PROVIDE 4" SANITARY W/ DEEP SEAL P-TRAP UP TO FD/TD
4
PROVIDE 2"V PIPE UP.
5
PROVIDE 3"SAN PIPE UP.
6
PROVIDE TD-1 AND CONNECT TO CB-1.
7
PROVIDE CB-1 AND CONNECT TO 4"WASTE PIPE.
8
PROVIDE OI-1 AND ALL ASSOCIATED ACCESSORIES. CONNECT TO 4"SAN
PIPE TO OUTLET, 4"OW PIPE TO INLET, AND 2"V PIPE IN SLAB.
9
PROVIDE OI-2 AND ALL ASSOCIATED ACCESSORIES. CONNECT TO 4"SAN
AND 2"V PIPES IN SLAB.
10
PROVIDE 1-1/4" G PIPE UP. REFER TO P101 AND CIVIL DRAWINGS FOR
CONTINUATION.
11
PROVIDE 2" CWS PIPE UP. REFER TO P101 DRAWING FOR CONTINUATION.
12
PROVIDE 4"FP PIPE UP. REFER TO FP101 DRAWING FOR CONTINUATION.
13
PROVIDE 4"SAN UP.
www.labellapc.com
2
4"SAN
4"OW
2
EXERCISE
112
LOCKER ROOM
113
L-1
4"SAN
4"OW
19
3"SAN
3
4"SAN
2"V
4"SAN
3
4
N
PROVIDE 4" SAN PIPE UP TO WALL CO.
19
EXTEND 4" OW PIPING TO EXTERIOR OIL SEPARATOR, SEE CIVIL
DRAWINGS FOR PIPE CONTINUATION.
52904
AR
RT
H CAROLI
NA
LOT TE , N .
C
.
9/16/2016
9/9/2016
L-1
TOWN OF DAVIDSON
2"V
4"SAN
3"SAN
4"OW
18
R A TI ON
PROVIDE 3" DEEPSEAL P-TRAP AT SD/MSB.
C
CERT. NO.
NO
CH
G S. BLYT
ES
PO
17
G INEER
AR
ASSOCI AT
I TE C TU R A
CH
L
OR
TD-1
PROVIDE 4" SAN PIPE. REFER TO CIVIL DRAWINGS FOR CONTINUATION.
AI
LA
C.
TD-1
16
SEAL
030515
EL
© 2016 LaBella Associates
P-1
6
PROVIDE 2" CWS UNDERGROUND PIPE. REFER TO CIVIL DRAWINGS FOR
CONTINUATION.
ES S IO N
I
P.
1
5
6
15
OF
EN
CR
BEDROOM
109
PROVIDE 4" FIRE SUPPRESSION UNDERGROUND PIPE. REFER TO CIVIL
DRAWINGS FOR CONTINUATION.
H CARO L
AL
14
T
OR
NA
CORRIDOR
108
NC LICENSE NO. C-0430
B
16
5
FD
BEDROOM
111
LA
4"SAN
4"SAN
4"SAN
4
PROVIDE 4" SAN PIPE UP TO CO.
ED
FD
2
4
R E GI S TE R
3
PROVIDE 4" SAN PIPE UP TO WC.
E
4
1
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
H
STORAGE
115
M
17
3"SAN
4"
SA
N
10
KEY NOTES:
PR
SS-1
3
5
3"SAN
1-1/4"G
DECONTAMINATION
114
MEN
107
216 South Main Street,
Davidson, NC 28036
4
4"SAN
2
AN
S
3"
2"V
5
17
4
KITCHEN
SK-1
105
SH-1
SH-1
2"V
2
17
FCO
4"SAN
WOMEN
106
4
4"SAN
2
3"SAN
FCO
L-1
P-1
1
5
4"OW
7
7
4
4"OW
4"OW
WCO
PANTRY
104
LINEN
103
4"OW
4
4"OW
4"OW
CB-1
CB-1
FIRE STATION #2
4"OW
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
WCO
2
BAY 1
118
BAY 2
119
6
6
TD-1
TD-1
5
9/16/16
INTERACTIVE REVIEW COMMENTS
4
9/14/16
INTERACTIVE REVIEW COMMENTS
3
09/07/16
PERMITTING COMMENTS
2
08/15/16
1
08/10/16
NO:
DATE:
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
REVISIONS
PROJECT NUMBER:
LIVING
102
2151374
DRAWN BY:
PAV/DWM
REVIEWED BY:
BB
ISSUED FOR:
CONSTRUCTION
DATE:
07.25.16
DRAWING NAME:
OFFICE
101
ENTRY
100
11
2"
SPRINKLER
CLOSET
101A
12
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
UNDER SLAB PLUMBING
FLOOR PLAN
Engineering
Architecture
Environmental
Planning
www.labellapc.com
4"
NC LICENSE NO. C-0430
A
H
L L
A
R
S
S
O
I
.
P
A
C H
I
E
T
L A
B
L
A
.
C
L
O
F
D
P
O
I
A
R
T
H
C
N
CRA
A
G
R
I
C
N I A R
E G IS T
R
E E
S
N
A R
.
NO
O
T O
I
T
CERT. NO.
52904
N
H
T
LO
T
E
,
A
L E
YT
H
E
T C U
R
.
.
E
R
R O
L
R
B
C
A
N
I NE
R
I
G
S
E
O
L
E S S ON
SEAL
030515
E
C
O
RP
A
CAR
T
N
C
9/16/2016
9/9/2016
© 2016 LaBella Associates
TOWN OF DAVIDSON
216 South Main Street,
Davidson, NC 28036
FIRE STATION #2
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
5
4
9/16/16
9/14/16
INTERACTIVE REVIEW COMMENTS
INTERACTIVE REVIEW COMMENTS
3
2
09/07/16
08/15/16
1
NO:
08/10/16
DATE:
PERMITTING COMMENTS
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
REVISIONS
PROJECT NUMBER:
2151374
DRAWN BY:
REVIEWED BY:
ISSUED FOR:
DATE:
CONSTRUCTION
07.25.16
DRAWING NAME:
DRAWING NUMBER:
00/00/0000 00:00AM
FLPTH
15
14
1
UNDERSLAB
P100 1/4" = 1'-0"
PLUMBING FLOOR PLAN
N
4"
DRAWING NUMBER:
MECKLENBURG COUNTY
CODE ENFORCEMENT
2"
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-100
TOTAL GAS LOAD = 580 MBH
TOTAL DEVELOPED LENGTH = 150'
GAS PRESSURE = <2.0 PSI
GAS METER BY GAS CO.
GAS PIPING SIZED PER TABLE 402.4(2) OF THE
NCSBC: FUEL GAS CODE 2012
11
KEY NOTES:
SS-1
2
4
17
1
PROVIDE WC-1 AND ALL ASSOCIATED ACCESSORIES. CONNECT TO 1/2"CW PIPE IN WALL AND 4"SAN PIPE IN
SLAB.
2
PROVIDE 4" FCO.
3
1"CW, 3/4" HW AND 2"V PIPES UP.
4
PROVIDE SH-1 (ADA) AND ALL ASSOCIATED ACCESSORIES. CONNECT 1/2"CW AND HW PIPEING IN WALL TO
SHOWER CONTROLS. CONNECT SHOWER TRENCH DRAIN TO 4"SAN PIPE IN SLAB.
5
PROVIDE L-1, 1-1/2" P-TRAP, FAUCET, AND ALL ASSOCIATED ACCESSORIES. CONNECT 1/2"CW AND HW PIPES
IN WALL TO FAUCET. CONNECT P-TRAP TO 4" SAN PIPE IN FLOOR AND CONNECT 1-1/2" V PIPE DOWN.
6
PROVIDE 2"V PIPE DN AND CONNECT TO 2"V PIPE IN SLAB.
7
PROVIDE DOUBLE BOWL SINK 'SK-1', 1-1/2" P-TRAP, FAUCET, SINK DISPOSAL 'SD-1', AND ALL ASSOCIATED
ACCESSORIES. CONNECT 1/2"CW AND HW PIPES IN WALL TO FAUCET. CONNECT P-TRAP TO 4" SAN PIPE IN
FLOOR AND CONNECT 1-1/2" V PIPE DOWN.
8
2" CWS MAIN PIPE UP TO ATTIC SPACE. PROVIDE SHUT OFF AT BASE.
9
PROVIDE 2"V PIPE DN AND CONNECT TO 2"V PIPE IN SLAB. CONNECT 2"V NEAR FLOOR TO 2"V PIPE AS SHOWN
AND THEN RUN UP ALONG WALL TO APPROX. 12' AFF. TERMINATE WITH AIR ADMITTANCE VALVE INSIDE
OX-BOX MOUNTED TO INTERIOR WALL.
FCO
M
13
16
FD-1
FD-1
12
1"G TO
GENERATOR
FD-1
2V"
12
6
FD-1
ED-1
15
6
2V"
W/D
STACKED
29
2V"
12
NFWHB-1
1/2"TW
19
23
EW-1
18
6
14
3/4"HW
3/4"CW
2"V
13
4
2"V
25
26
CB-1
1
L-1
WC-1
16
PROVIDE 2"V PIPE UP TO MEZANINE/ATTIC.
17
PROVIDE NATURAL GAS PRESSURE REGULATOR, METER, AND ALL ASSOCIATED ACCESSORIES. CONNECT
1-1/4"G PIPE TO INLET OF REGULATOR. PROVIDE AND CONNECT 2"G PIPE TO REGULATOR AND METER.
CONNECT 2"G PIPE TO METER OUTLET AND UP SIDE OF BUILDING.
18
PROVIDE WASH MACHINE CONNECTION BOX, WITH TWO 3/4" VALVES WITH WATER HAMMER ARRESTERS EA
FOR CW AND HW HOSE CONNECTIONS, 3/4"CW AND HW PIPES UP IN WALL, 2" WASTE CONNECTION, AND ALL
ASSOCIATED ACCESSORIES. SEE DETAIL 1 ON DRAWING P502 FOR MORE INFORMATION.
19
PROVIDE WASH MACHINE CONNECTION BOX, WITH TWO 1/2" VALVES WITH WATER HAMMER ARRESTERS EA
FOR CW AND HW HOSE CONNECTIONS, 1/2"CW AND HW PIPES UP IN WALL, 2" WASTE CONNECTION DN, AND
ALL ASSOCIATED ACCESSORIES. CONNECT 2" WASTE PIPE TO 4" WASTE PIPE IN SLAB. CONNECT 1-1/2"V PIPE
DN TO WASTE PIPE. SEE DETAIL 1 ON DRAWING P502 FOR MORE INFORMATION.
20
PROVIDE 3/4" GAS SUPPLY PIPE DN AND CONNECT TO STOVE AND TO MAIN IN MEZZANAINE/ATTIC.
21
PROVIDE SIOUX CHIEF ICE MAKER OUTLET BOX WITH 1/2" CW SUPPLY QUARTER -TURN BALL VALVE AND A
1/2" X 1/4" OD COMPRESSION OUTLET. PROVIDE OUTLET BOX WITH FRAME AND STAINLESS STEEL HOSE FOR
CONNECTION TO REFRIGERATOR ICE MAKER.
22
4"FP PIPE UP. REFER TO FP101 DRAWING FOR CONTINUATION.
23
PROVIDE VALVE CONNECTION BOX, WITH TWO 1/2" VALVES WITH WATER HAMMER ARRESTERS EA FOR CW
AND HW HOSE CONNECTIONS, 1/2"CW AND HW PIPES UP IN WALL. SEE DETAIL 1 ON DRAWING P502 FOR MORE
INFORMATION.
2"V
NFWHB-2
SD-1
7
1/2"
SK-1
10
1-1/2"V
1/2"
PROVIDE NFWHB-1 AND ALL ASSOCIATED ACCESSORIES. CONNECT TO IN WALL 1/2" CW AND HW PIPING.
30
1/2"HW
1/2"CW
FCO
5
20
FCO
SD-1
6
2
FCO
25
1-1/2"V
SH-1
2"V
SH-1
2
2
1/2"HW
1/2"CW
1/2"
15
CB-1
52904
NO
AR
RT
H CAROLI
NA
LOT TE , N .
C
9/20/2016
9/9/2016
© 2016 LaBella Associates
TOWN OF DAVIDSON
6
4
6
FIRE STATION #2
CB-1
9
CERT. NO.
2"V
26
CB-1
CH
C
TI ON
5
1/2"
PROVIDE SAFETY SHOWER SSH-1, TEMPERED WATER MIXING VALVE, AND ALL ASSOCIATED ACCESSORIES.
PROVIDE AND CONNECT 1/2" CW AND HW PIPING TO MIXING VALVE. PROVIDE AND CONNECT 1/2" TEMPERED
WATER PIPING TO MIXING VALVE AND SHOWER.
G S. BLYT
ES
OR A
2"V
L-1
14
3
WC-1
1-1/2"V
PROVIDE 2" SAN W/ DEEP SEAL P-TRAP UP TO DRAIN PAN ON MEZZAININE/ATTIC. ROUTE PIPING TO EXTERIOR
WALL DOWN TO SPLASH BLOCK. PROVIDE AIR GAP PER CODE.
AR
ASS O CI AT
I TE C TU R A
CH
L
RP
6
13
G INEER
LA
O
1
PROVIDE FD-1 AND CONNECT TO 4"SAN PIPE IN SLAB.
SEAL
030515
EN
AI
E S S IO N
EL
C.
13
12
CR
21
PROVIDE SS-1, 1-1/2" P-TRAP, FAUCET, AND ALL ASSOCIATED ACCESSORIES. CONNECT 1/2"CW AND HW PIPES
IN WALL TO FAUCET. CONNECT P-TRAP TO 4" SAN PIPE IN FLOOR AND CONNECT 1-1/2" V PIPE DOWN.
OF
I
P.
11
PROVIDE 1/2" HW PIPE AND CONNECT TO DISHWASHER. PROVIDE WASTE HOSE AND CONNECT FROM
DISHWASHER TO SD-1 DISHWASHER TYE-IN POINT.
H C ARO L
AL
10
T
OR
NA
SSH-1
NC LICENSE NO. C-0430
.
LI-1
B
MSB-1
LA
28
24
ED
2V"
6
R E GI S TE R
6
2
FCO
E
2V"
H
2V"
12
L-1
N
2V"
5
PR
2"G UP
9
24
PROVIDE LINT INTERCEPTOR LI-1. SEE P-100 FOR ADDITIONAL INFORMATION.
25
PROVIDE TD-1 AND ALL ASSOCIATED ACCESSORIES. SEE P-100 FOR ADDITIONAL INFORMATION.
26
PROVIDE CB-1 AND ALL ASSOCIATED ACCESSORIES. SEE P-100 FOR ADDITIONAL INFORMATION.
27
1-1/2" CWS TRUCK FILL LINE MOUNT 36" AFF. EXTEND 1-1/2" CWS UP TO ATTIC SPACE CONTINUE ON P-102.
COORDINATE CONNECTION WITH FIRE DEPARTMENT AHJ.
2
FCO
28
PROVIDE MOP SERVICE BASIN MSB-1, DRAIN, WALL MOUNTED FAUCET, WITH PAIL HOOK AND ALL
ASSOCIATED ACCESSORIES.
29
PROVIDE 4" WASTE AND CONNECT TWO 2" WASTE FROM WASHER BOXES. EXTEND 2" VENT UP VENT SYSTEM IN
CEILING.
30
PROVIDE NFWHB-2 AND ALL ASSOCIATED ACCESSORIES. CONNECT TO IN WALL 1/2" CW PIPING.
6
9/20/16
INTERACTIVE REVIEW COMMENTS
5
9/16/16
INTERACTIVE REVIEW COMMENTS
4
9/14/16
INTERACTIVE REVIEW COMMENTS
3
09/07/16
PERMITTING COMMENTS
2
08/15/16
1
08/10/16
NO:
DATE:
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
REVISIONS
25
25
PROJECT NUMBER:
DRAWN BY:
PAV/DWM
REVIEWED BY:
BB
ISSUED FOR:
DATE:
DRAWING NAME:
FIRE TRUCK FILL
CONNECTION
15
NFWHB-1
27
8
22
00/00/0000 00:00AM
FLPTH
DRAWING NUMBER:
MECKLENBURG COUNTY
CODE ENFORCEMENT
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-101
11
27
KEY NOTES:
14
WH-2
1
PROVIDE 2" GAS RISER UP FROM GAS REGULATOR. SUPPORT PIPING FROM WALL.. PAINT EXTERIOR PIPING.
2
ROUTE GAS PIPING AS SHOWN IN ATTIC SPACES. PROVIDE HANGERS AND GAS SHUT OFF VALVES AS INDICATED
AND REQUIRED BY CODE.
3
PROVIDE 1" GAS DN TO GF-1 WITH DRIP LEG, SHUT OFF VALVE AND REGULATOR. FINAL CONNECTION BY
EQUIPMENT INSTALLER.
4
PROVIDE 3/4" GAS DN TO RADIANT HEAT BURNERS, IRH-1 THRU 4 WITH DRIP LEG, SHUT OFF VALVE AND
REGULATOR. FINAL CONNECTION BY EQUIPMENT INSTALLER.
5
PROVIDE 3/4" GAS DN TO GAS STOVE IN KITCHEN WITH DRIP LEG, SHUT OFF VALVE AND REGULATOR. FINAL
CONNECTION BY EQUIPMENT INSTALLER.
6
PROVIDE 2"V PIPE DN
7
PROVIDE 1" GAS DN TO WH-1 AND WH-2. CONNECT TO WG WITH DRIP LEG AND GAS SHUT OFF VALVE. RUN GAS
PIPING ON MEZZANINE WALL.
8
PROVIDE 4" VENT UP THRU ROOF. COORDINATE ROOF PENETRATION AND FLASHING WITH ROOFING INSTALLER.
9
PROVIDE 1/2" CW AND 1/2" HW DN TO DOMESTIC HOSE CONNECTION BOX. PROVIDE ALL ASSOCIATED
ACCESSORIES.
10
PROVIDE 2"V PIPE DN AND CONNECT TO 2"V PIPE IN SLAB.
21
2"V
HWCP-2
15
1"
13
28
1/2"
1"
2"V
10
20
1"G
(210 CFH)
1"
WH-1
1"G
(210 CFH)
28
16
PROVIDE 1/2" CW AND 1/2" HW, 1-1/2" WASTE PIPE DN TO L-1. RUN BRANCH PIPING IN ATTIC AS SHOWN.
17
PROVIDE 3/4" CW AND 3/2" HW, 2" WASTE PIPE DN TO MSB-1. RUN BRANCH PIPING IN ATTIC AS SHOWN.
18
PROVIDE 3/4" CW AND 3/4" HW DN TO EQUIPMENT WASH MACHINE CONNECTION BOX. PROVIDE ALL
ASSOCIATED ACCESSORIES. SEE WASH MACHINE CONNECTION BOX DETAIL FOR MORE INFORMATION.
19
PROVIDE 1/2" CW AND 1/2" HW DN TO DOMESTIC WASH MACHINE CONNECTION BOX. PROVIDE ALL
ASSOCIATED ACCESSORIES. SEE WASH MACHINE CONNECTION BOX DETAIL FOR MORE INFORMATION.
20
PROVIDE 1/2"CW AND 1/2" HW DROPS DOWN TO TEMPERED WATER MIXING VALVE SERVING SSH-1.
21
PROVIDE HWCP-2, 1/2" CHECK VALVE, AND ALL ASSOCIATED ACCESSORIES. CONNECT TO 1/2" HWR PIPING.
SEE DETAIL 12/P501 FOR MORE INFORMATION.
3/4"G
(80 CFH)
HWCP-1
22
PROVIDE 1" CW AND 3/4" HW DROPS DN TO PLUMBING EQUIPMENT IN KITCHEN AND MENS AND WOMENS
SHOWER ROOMS.
23
PROVIDE 1/2' CW AND 1/2" HW DN AND CONNECT TO NFHB-1.
24
2" CW UP FROM WATER SUPPLY CLOSET.
25
4"FP PIPE UP. REFER TO FP101 DRAWING FOR CONTINUATION
26
PROVIDE 1-1/2" DROP DN TO TRUCK FILL CONNECTION. PROVIDE DOUBLE CHECK VALVE ASSEMBLY ON PIPE
DROP.
27
PROVIDE 1/2" CW AND 1/2" HW DROPS DN AND CONNECT TO SH-1 IN LOCKER ROOM.
28
PROVIDE 1/2" BALANCE VALVE, CHECK VALVE, SHUT-OFF VALVE AND ALL ASSOCIATED ACCESSORIES.
CONNECT TO 1/2" HW AND HWR PIPING.
29
PROVIDE HWCP-1, 1/2" CHECK VALVE, AND ALL ASSOCIATED ACCESSORIES. CONNECT TO 1/2" HWR PIPING.
SEE DETAIL 12/P501 FOR MORE INFORMATION.
30
PROVIDE CONDENSATE DRAIN LINE TO 1" P-TRAP BELOW MEZZANINE FLOOR AND ROUTE TO EXTERIOR WALL.
PROVIDE SPLASH BLOCK. CONDENSATE DRAIN LINE BY EQUIPMENT INSTALLER. MAINTAIN AIR GAP PER CODE.
2
1" CD
HP-1
3/4"G
(40 CFH)
1"G
(80 CFH)
4
2" CW
RT
H CAROLI
NA
LOT TE , N .
C
TOWN OF DAVIDSON
216 South Main Street,
Davidson, NC 28036
3/4"
MECHANICAL PLATFORM
---
1-1/2"G
(160 CFH)
PROVIDE DRAIN PAN W/ 2" DRAIN FOR WH. CONNECT 2" DRAIN TO 2" P-TRAP BELOW MEZZANAINE FLOOR AND
ROUTE TO EXTERIOR WALL. PROVIDE SPLASH BLOCK. PIPING BY EQUIPMENT INSTALLER. MAINTAIN AIR GAP
PER CODE.
AR
© 2016 LaBella Associates
29
1/2"
15
52904
9/14/2016
9/9/2016
1"
7
1" G
PROVIDE WH-2 AND CONNECT TO 1" CW AND 1" HW PIPING. PROVIDE MIXING VALVE, T&P RELIEF VALVE, DRAIN
PAN AND ALL ASSOCIATED ACCESSORIES PER WATER HEATER DETAIL AND SPECS
C
CERT. NO.
NO
CH
G S. BLYT
ES
TI ON
22
14
AR
ASS O CI AT
I TE C TU R A
CH
L
OR A
13
PROVIDE EXPANSION TANK SIZED FOR WATER HEATER AND INSTALL PER WATER HEATER DETAIL AND SPECS.
LA
RP
6
5
8
13
G INEER
EL
O
15
12
3/4"G
(40 CFH)
AI
2
2"V
4
PROVIDE WH-1 AND CONNECT TO 1" CW AND 1" HW PIPING. PROVIDE MIXING VALVE, T&P RELIEF VALVE, DRAIN
PAN AND ALL ASSOCIATED ACCESSORIES PER WATER HEATER DETAIL AND SPECS.
E S S IO N
SEAL
030515
EN
CR
2
12
OF
I
C.
1"
PROVIDE 1/2"CW AND 1/2" HW PIPES DN IN WALL TO FAUCET ON SS-1. DROP 1-1/2" V PIPE DOWN AND
CONNECT TO WASTE PIPING.
H C ARO L
AL
11
T
OR
P.
N
8
NC LICENSE NO. C-0430
NA
1-1/2"G
(160 CFH)
19
18
1"
.
1/2"
B
1"G
(210 CFH)
2"G
(580 CFH)
LA
1"
ED
3"V
1"
2
R E GI S TE R
2
9
HP-2
1/2"
17
23
MEZZANINE
---
E
2"G
(580 CFH)
2"V
16
H
2"G UP
(580 CFH)
1"
1"G
(130 CFH)
1
www.labellapc.com
PR
6
1" CD
7
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
4
FIRE STATION #2
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
4
9/14/16
INTERACTIVE REVIEW COMMENTS
3
09/07/16
PERMITTING COMMENTS
2
08/15/16
1
08/10/16
NO:
DATE:
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
REVISIONS
PROJECT NUMBER:
2151374
DRAWN BY:
1/2"
PAV/DWM
REVIEWED BY:
BB
ISSUED FOR:
CONSTRUCTION
DATE:
07.25.16
DRAWING NAME:
4
3/4"G
(40CFH)
3/4"G
(40CFH)
PLUMBING
MEZZANINE PLAN
24
4
1-1/2" CWS
1/2"
1/2" CW
1-1/2"
00/00/0000 00:00AM
FLPTH
23
26
DRAWING NUMBER:
25
MECKLENBURG COUNTY
CODE ENFORCEMENT
1
PLUMBING
P102 1/4" = 1'-0"
MEZZANINE PLAN
N
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-102
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
www.labellapc.com
B
ED
52904
AR
RT
H CAROLI
NA
C
.
E
TI ON
H
C
CERT. NO.
NO
CH
G S. BLYT
ES
OR A
R E GI S TE R
LA
AR
ASS O CI AT
I TE C TU R A
CH
L
RP
CR
G I N EER
LA
O
SEAL
030515
EN
AI
E S S IO N
EL
C.
OF
I
AL
PR
H CARO L
P.
O
RT
NA
N
NC LICENSE NO. C-0430
L OT TE , N .
9/16/2016
9/9/2016
© 2016 LaBella Associates
TOWN OF DAVIDSON
216 South Main Street,
Davidson, NC 28036
5
FIRE STATION #2
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
5
9/16/16
INTERACTIVE REVIEW COMMENTS
4
9/14/16
INTERACTIVE REVIEW COMMENTS
3
09/07/16
PERMITTING COMMENTS
2
08/15/16
1
08/10/16
NO:
DATE:
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
REVISIONS
PROJECT NUMBER:
2151374
DRAWN BY:
PAV/DWM
REVIEWED BY:
BB
ISSUED FOR:
CONSTRUCTION
DATE:
07.25.16
DRAWING NAME:
3
1
PLUMBING RISER DIAGRAM
00/00/0000 00:00AM
FLPTH
DRAWING NUMBER:
MECKLENBURG COUNTY
CODE ENFORCEMENT
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-401
INSTALL WATER HAMMER
ARRESTOR JUST BEFORE LAST
FIXTURE ON BRANCH LINE
INSTALL WATER HAMMER
ARRESTOR ON ALL
FIXTURES WITH QUICK
CLOSING VALVES.
MEMBRANE CLAMPING
COLLAR AND SEEPAGE PAN
PROVIDE CLEANOUT TEE WITH SCREWED
COUNTERSUNK ABS PLASTIC PLUG. CLEANOUT
FACE SHALL BE WITHIN 4" OF WALL SURFACE.
PROVE EXTENSION IF REQUIRED
3/4"CW
3/4"HW
www.labellapc.com
INSTALL AN ADDITIONAL WATER
HAMMER ARRESTOR IF THE BRANCH
LINE IS GREATER THAN 20' LONG.
SINGLE OR
DOUBLE FIXTURE
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
LOCKABLE BALL VALVE
CONCRETE FLOOR
MULTIPLE FIXTURES
REDUCING TRAP
PDI
SIZE
MAXIMUM TAILPIECE
LENGTH IS 2 FEET
SLOPE WASTE AT TWO
PERCENT
3/4"
12-32
URINAL
4
--
C
1"
33-60
LAVATORY/SINK
1.5
1.5
D
1-1/4"
61-113
JANITOR'S SINK
3
3
E
1-1/2"
114-154
F
2"
154-330
AR
ES
C
CERT. NO.
52904
NO
CH
G S. BLYT
ASSOCI AT
I TE C TU R A
CH
L
R A TI ON
G INEER
LA
PO
SAFETY SHOWER AND EYEWASH DETAIL
E S S IO N
SEAL
030515
EN
AI
4
OF
EL
OR
FLOOR LINE
H CARO L
C.
WATER HAMMER ARRESTER DETAIL
T
OR
P.
3
NONE
COMBINATION DRENCH
SHOWER AND
EYE/EYE-FACE WASH
BRADLEY MODEL S19-310
NC LICENSE NO. C-0430
AL
FLOOR DRAIN AND SINK DETAIL
TMV - NAVIGATOR
EFX S19-2100 WITH
CABINET
A
COMMENTS:
1. WATER HAMMER ARRESTERS SHALL BE HAVE PISTON AND 0-RING CONSTRUCTION WITH
PDI #WH-201, ASSE # 1010 AND ANSI # A112.26.1M CERTIFICATION. INSTALL IN HORIZONTAL
OR VERTICAL POSITION, BUT NEVER UPSIDE DOWN. SIZE THE UNITS AS SHOWN PER THE
TABLES SHOWN ABOVE.
NONE
CHECK
VALVES
EMERGENCY FACE
WASH/EYE
B
B
PULL-ROD HANDLE
AT 69" A.F.F.
LA
--
ED
5
R E GI S TE R
VALVE WATER CLOSET
E
1-11
IN
2
1/2"
H
MAXIMUM 8' ON 2"
WASTE OR 10' ON 3".
A
CR
WALL CLEANOUT
NONE
HOT
1" TW
COMMENTS:
1.
LOCATE FLOOR DRAIN/SINK WHERE SHOWN ON DIMENSIONED FLOOR PLAN. IF SITUATION IS
FLOOR SLAB ON GRADE, SET DRAIN BODY IN PLACE, PROVIDE BACKFILL, AND POUR
AROUND IT. RECESS TOP OF FLOOR DRAINS 1/2" BELOW FLOOR DATUM AND SLOPE FLOOR
TO IT. DO NOT RECESS FLOOR SINKS.
2. OTHER VENTING METHODS MAY BE USED, IF APPROVED BY LOCAL CODE AND/OR LOCAL
AUTHORITIES.
COMMENTS:
PROVIDE WALL CLEANOUT (WCO) WHERE SHOWN
ON PLAN AND ON SANITARY WASTE BRANCHES
NOT SERVED WITH A FLOOR CLEANOUT.
COLD
N
LONG SWEEP AT END OF LINE
OR COMBINATION WYE
FIXTURE
PR
PROVIDE TRAP PRIMER IF REQUIRED BY
LOCAL AUTHORITIES OTHERWISE
DEEP-SEAL P-TRAP
WATER SUPPLY FIXTURE UNIT (WSFU)
FIXTURE
UNIT LOAD
42" AFF
MAXIMUM 12' WHERE
ENLARGED 4" WASTE LINE IS
USED AS A COMBINATION
WASTE AND VENT SYSTEM
HUB AT FLOOR
PIPE
SIZE
33" - 45" A.F.F.
PROVIDE A ROUND 18 GAUGE
STAINLESS STEEL COVER FOR
CONSEALED CLEANOUTS
1
GALVANIZED OR STAINLESS
STEEL TO MATCH SAFETY
SHOWER EQUIPMENT
AR
RT
H CAROLI
NA
L OT TE , N .
C
.
9/9/2016
NONE
© 2016 LaBella Associates
WALL
WATER CLOSET
TOP BEAM C-CLAMP
IF STEEL BAR JOIST.
SEAT
ADJUSTABLE BAND
HANGER FOR
PIPING FOUR INCH
OR LESS.
CHASE
STORM COLLAR
PROVIDE COPPER OR
NON-METALLIC
COATING WHERE
HANGERS CONTACT
BARE COPPER PIPE.
NOTES:
C.W. SUPPLY
216 South Main Street,
Davidson, NC 28036
STEEL DECK
SEAL ALL AROUND
DO NOT HANG PIPE LARGER THAN 4"
FROM BOTTOM OF JOISTS, AND HANG
ONLY AT PANEL POINT.
VENT
PROVIDE GALVANIZED STEEL SADDLE FOR ALL
INSULATED PIPE 1" AND LARGER. VERIFY
INSULATION THICKNESS WHEN SIZING HANGERS.
DO NOT SUSPEND OTHER ITEMS FROM PIPE.
WATER CLOSET
FINISHED FLOOR
CONCRETE SLAB
WATER CLOSET FLOOR FLANGE
ESCUTCHEON
4" SAN TO NEAREST MAIN
ANCHOR PIPE TO ROOF DECK OR JOISTS WITH
U-BOLT AROUND PIPE AND ANGLE IRON
WELD- ED OR SCREWED TO DECK OR JOIST
ROOF
H
OPENING IN ROOF
FLUSH VALVE
HOLDRITE BRACING
4" SAN
ELEVATION
FL MTD TANK TYPE WATER CLOSET DETAIL
NONE
COMMENTS:
1. PROVIDE UPPER ATTACHMENT AS REQUIRED FOR CASES NOT SHOWN HERE. DO NOT INSTALL
HANGER INSIDE INSULATION OR OTHERWISE PENETRATE VAPOR BARRIER. DO NOT HANG ONE PIPE
FROM ANOTHER EXCEPT IN CHASES. TRAPEZE HANGERS MAY BE USED FOR MULTIPLE PARALLEL
PIPES. SLOPE ALL WATER PIPING SLIGHTLY TOWARD DRAINABLE LOCATIONS. HANGER SPACING FOR
PIPE SIZE: COPPER: 2"=9' 1 1 2 "=8' 1 1 4 "=7' 1"=6' 3 4 "=6' 3 4 "=5'. CAST IRON: 10' AND ONE
NEAR ALL JOINTS. STEEL: 3"=12' 2 1 2 "=11' 2"=10' 1 1 2 "=9' 1"=7' 3 4 "=6' 1 2 "=5'. LOCATE
HANGERS AS CLOSE AS POSSIBLE TO TURNS AND TEES OF PIPE. PROVIDE SUPPLEMENTARY STEEL
STRUTS BETWEEN JOISTS IF REQUIRED. LOCATE HANGERS TO TAKE LOAD OFF OF EQUIPMENT
CONNECTIONS. ANCHOR WATER PIPE AGAINST SWAYING DUE TO CHANGES IN WATER VELOCITY.
PROVIDE SEISMIC BRACING AS REQUIRED BY LOCAL AUTHORITIES. CHAINS OR PERFORATED STRAP
IRON OR STEEL IS NOT ACCEPTABLE. DO NOT SUSPEND PIPE FROM JOIST BRACING MEMBERS.
REFER TO CODES AND SPECIFICATIONS FOR FURTHER INFORMATION.
6
CW (IN)
BALL VALVE
(TYP.)
FLASHING BY ROOFING
CONTRACTOR
HUBLESS PIPE CONNECTORS
ON CAST IRON PIPE.
PROVIDE PIPE INCREASER
WHERE REQUIRED TO MAKE
MINIMUM 3" VENT THRU ROOF
SEAT
KHW 140°F (IN)
FLASHING SKIRT
CLEVIS HANGER FOR PIPE
OVER FOUR INCH.
1. FOR CONTINUATION OF PIPING SEE PLANS.
2. MINIMUM CHASE SPACE SHOWN MUST BE CLEAR SPACE.
PLAN VIEW
2'-0" MIN.
VENT
5
TOWN OF DAVIDSON
ALL-THREAD ROD.
LENGTH AS REQ'D FOR
PIPE SLOPE.
M
COMMENTS:
1.
REFER TO PLANS FOR VTR PIPE SIZES AND LOCATIONS.
2.
7
NONE
WATTS MMV ASSE 1070
MIXING VALVE WITH
TEMPERATURE ADJUSTMENT
UNION (TYP.)
LOCATE VTR MINIMUM THREE FEET FROM PROPERTY LINE, OR TEN FEET
HORIZONTAL OR THREE FEET VERTICAL ABOVE ANY BUILDING OPENING OR
FRESH AIR INTAKE, OR ONE FOOT FROM ANY VERTICAL SURFACE.
3.
PIPE HANGER DETAIL
C
FIRE STATION #2
TW 110°F (OUT)
LOCATE VTR MINIMUM 18" FROM PARAPET, EXPANSION JOINT, EQUIPMENT
CURB, ETC. OFFSET IN CEILING SPACE WHERE REQUIRED TO MEET THESE
CONDITIONS.
VENT THRU ROOF (VTR) DETAIL
NONE
8
THEMOSTATIC MIXING VALVE
NONE
PIPING HANGER SUPPORTS
GAS BRANCH TO EQUIPMENT
EXTEND 1/2" HW, 1/2" CW AND
1-1/2" VENT ABOVE CEILING AND
CONNECT TO NEAREST ACTIVE MAIN.
CONNECT VENT SYSTEM
ABOVE CEILING
1-1/2"
CONTINUOUSLY WELDED WATER
STOP & ANCHOR COLLAR,
WATERPROOF FLOORS ONLY. MIN.
1" ALL OTHERS TO HAVE ANCHOR
LUGS (MIN. 3 REQ'D).
WATERPROOF CAULK
LAVATORY SUPPORT
FOR CONCEALED ARM
1/2" HW
PIPE SLEEVE
PIPE INSULATION
(WHERE REQ'D)
6"
LAVATORY
1-1/2" P-TRAP
1-1/2"
STOP
VALVE TYP.
CUT OPENING IN EXISTING
PRESSURE INJECT EPOXY
GROUT TO COMPLETELY FILL
ANNULAR SPACE BETWEEN
PIPE AND WALL . SEE
SPECIFICATION 030130
MAINTENANCE OF CONCRETE.
P-TRAP W/CO
1-1/2"
00/00/0000 00:00AM
FLPTH
FLOOR
PRESSURE INJECT EPOXY GROUT
TO COMPLETELY FILL ANNULAR
SPACE BETWEEN PIPE AND WALL .
SEE SPECIFICATION 030130
MAINTENANCE OF CONCRETE.
NONE
LAVATORY DETAIL
NONE
TYPICAL PIPE SLEEVE THROUGH FLOOR DETAIL
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code.
It Is The Responsibility Of The
NONE
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
11
COUNTERTOP SINK DETAIL
1
08/10/16
NO:
DATE:
PERMITTING COMMENTS
ADDENDUM 2
PERMITTING COMMENTS
DESCRIPTION:
DRAWN BY:
T & P VALVE
REVIEWED BY:
SHUT OFF VALVE (TYPICAL)
ISSUED FOR:
PAV/DWM
BB
CONSTRUCTION
UNION (TYPICAL)
WASTE LINE
FROM SINK
DATE:
MANUAL SHUT-OFF VALVE ( GAS COCK) WITH AN 1/8"
N.P.T. PLUGGED TAPPING ACCESSIBLE FOR TEST
GAGE CONNECTION TO BE INSTALLED UPSTREAM OF
THE GAS SUPPLY CONNECTION TO THE APPLIANCE
MEZZANINE FLOOR
GROUND JOINT UNION
COMMENTS:
1. PIPING SHOWN IS SCHEMATIC. PROVIDE CLEARANCES RECOMMENDED BY
MANUFACTURER. PROVIDE SEISMIC STRAPPING AS REQUIRED.
2. SET THERMOSTAT AT 130°F.
12
NONE
WATER HEATER DETAIL
07.25.16
DRAWING NAME:
WH-1
DRAIN VALVE
6" DRIP LEG
WITH CAP
EXTEND 1/2" HW, 1/2" CW AND
1-1/2" VENT ABOVE CEILING
AND CONNECT TO NEAREST
ACTIVE MAIN.
MECKLENBURG COUNTY
CODE ENFORCEMENT
10
1-1/2"
FIRE RESISTANT
SILICONE FOAM SEALER
CONNECT WASTE PIPING TO
SANITARY MAIN BELOW FLOOR
9
1/2" CW
WASTE
LATERIAL
CONCRETE FLOOR SLAB
08/15/16
2151374
EXPANSION
TANK
1-1/4"
METAL DECK
PROVIDE CONNECTION
TO DOMESTIC
HOT & COLD WATER AND
HOT WATER RECIRCULATION
PIPING.
SINK
CUT OPENING IN EXISTING
09/07/16
2
PROJECT NUMBER:
THERMOMETER (TYPICAL)
VENT LINE
FROM SINK
CABINET
3
REVISIONS
BALANCING VALVE (TYPICAL)
1/2" CW
STOP VALVE TYP.
HOT WATER RECIRCULATING PUMP
G
1/2" HW
G
PIPE
WALL
V
WALL
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
3
DRAIN PAN
2" WASTE
1
PLUMBING DETAILS
ROUTE TO
EXTERIOR WALL
P-TRAP
DRAWING NUMBER:
P-501
WASHING MACHINE
BOX (WMF-X)
2
2
1 " TEMPERED(T) WATER FROM
SHOWER SH-1(ADA). EXTEND
2
MIXING VALVE TO SHOWER HAND HELD SPRAY SYSTEM WITH
VACUUM BREAKER AND 60" HOSE. RUN PIPING IN WALL
CHASE AND ABOVE CEILING.
1
1-1/2" VENT
4
1/2"
1/2"
2
DROP12" H&C WATER DN TO TEMPERATURE CONTROL
MIXING VALVE. RUN PIPING IN WALL CHASE.
3
THERMOSTATIC TEMPERING VALVE SERVING SHOWER
1 " TEMPERED WATER TO HAND HELD
SH-2(ADA). CONNECT
2
SHOWER AND TO DIVERTER VALVE AND SHOWER HEAD.
1
1/2"
1/2"
INLET
C.O.
INLET
3" NG GAS TO GAS PRESSURE
BOOSTER SYSTEM
OIL SEPARATOR
3" NG TO BUILDING
5
SHOWER FLOOR DRAIN.
MAIN SHUT-OFF VALVE
6
2" VENT PIPE RUN TO NEAREST WALL AND UP TO VENT
SYSTEM IN CEILING.
EQUIPMENT PAD
SEE DETAIL
4"
12" MIN. DIRT LEG
GAS METER
3"
OUTLET
CR
EN
AI
1
2
WASHING MACHINE BOX DETAIL
NONE
3
ADA SHOWER DETAIL
NONE
4
GAS METER DETAIL
NONE
G INEER
G S. BL
B
LA
L
ES
C
CERT. NO.
52904
NO
CH
YT
I TE C TU R A
R ATI ON
3" P-TRAP
SEAL
030515
A
ASSOCI AT
H
RC
PO
FINISHED FLOOR
E S S IO N
LA
OR
3" SANITARY PIPE
OF
EL
C.
GAS METER AND REGULATOR SHALL
BE BY THE LOCAL GAS COMPANY.
H CARO L
I
ED
2" VENT PIPE
T
OR
P.
NOTES:
AL
7
NC LICENSE NO. C-0430
RUN VENTS BELOW GRADE TO BUILDING
WALL. EXTEND UP WALL TO ABOVE ROOF
AND ANCHOR VENTS SECURELY TO WALL.
NA
6
G
R E GI S T E R
5
OIL STORAGE VENT
NOTE:
E
2" WASTE
GAS MAIN BY GAS
COMPANY
3" WASTE PIPING. EXTEND PIPING TO NEAREST MAIN. PITCH TO
DRAIN MIN 1/8" PER FT.
7
SEPARATOR VENT
3"
N
2" TRAP AND
WASTE PIPE
www.labellapc.com
GRADE
48"
42" AFF
GENERATOR SHUT-OFF VALVE, LABELED IN
ACCORDANCE WITH NFPA 110
PRESSURE REGULATOR
UNION (TYPICAL)
3
4"
CAPPED TEST TEE
SHOWER HEAD. EXTEND 1/2" CW FROM DIVERTER VALVE
TO SHOWER HEAD PIPING TO BE CONCEALED IN WALL
CHASE.
4
HWS
72"
CWS
EXTENSION UP
TO GRADE
PR
HOSE VALVE
CONNECTION
CW
HW(125)
NOTES:
H
WATER HAMMER
ARRESTOR (WHA-X)
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
AR
RT
H CAROLI
NA
L OT T E , N .
C
.
07/25/16
OIL SEPARATOR DETAIL
NONE
© 2016 LaBella Associates
TOWN OF DAVIDSON
P&G CHEMICAL
DISPENSER
FLOOR SLAB ON GRADE
MEMBRANE CLAMP
AS REQUIRED FOR
DEPTH OF SEWER
P&G
CHEMICAL BOTTLE
HW AND CW ISOLATION VALVES
HW AND CW PIPING
(RUN BESIDE EACH OTHER IN WALL)
SAME SIZE AS SEWER UP TO 4"
MAXIMUM.
FAUCET AND VALVES
JANITOR'S SINK
LONG SWEEP ELBOW AT END OR
TURN OF RUN.
HUB AND SPIGOT
CAST IRON PIPE
BELOW FLOOR.
FIAT FAUCETS
MODEL 830-AA
COMBINATION WYE AND EIGHTH
BEND IN RUN. ENTER TOP OF
PIPE.
SANITARY SEWER
LINE
FINISHED FLOOR
DIRECTION OF
FLOW
COMMENTS:
1. EACH CHEMICAL DISPENSER MUST HAVE A DEDICATED WATER SUPPLY, LOCATED WITHIN 4 FEET OF
THE DISPENSER. IT MUST PROVIDE TEMPERED WATER (ADJUSTABLE FROM 60-120F) WITH A FLOW
RATE OF 4 GPM AT 40 PSI DYNAMIC/FLOWING PRESSURE (35 PSID MIN.). THE HOT AND COLD
WATER SUPPLY LINES MUST HAVE CHECK VALVES TO PREVENT HOT/COLD WATER CROSSOVER, IF
THE TEMPERING VALVE DOES NOT INCLUDE THEM. IT MUST INCLUDE A SHUTOFF VALVE TERMINATING
IN A 43 " GARDEN HOSE MALE FITTING.
MOP SINK MS-1
COMMENTS:
1. LOCATE AT BUILDING EXIT, AT ENDS OF RUNS, AT TURNS OF PIPE GREATER
THAN 45 DEGREES, AT 50' INTERVALS ON STRAIGHT RUNS, AND/OR WHERE
SHOWN ON PLANS. PROVIDE BACKFILL PER ARCHITECTURAL SPECIFICATIONS.
LOCATE CLEANOUTS WHERE THERE IS 18" CLEAR AROUND. CONSULT LOCAL
CODES FOR OTHER FCO REQUIREMENTS.
FINISHED FLOOR
TO VENT MAIN.
2" VENT PIPING
2. ROUND SECURED GASKETED NICKEL BRONZE ADJUSTABLE TOP WITH "CO"
CAST IN COVER. PROVIDE CLEANOUT TOP WITH VARIATIONS SUITABLE FOR
FLOOR COVERING (CARPET MARKER, RECESSED FOR TILE, SCORIATED FOR
UNFINISHED FLOORS). PROVIDE GASKETED PLASTIC PLUG IN CAST IRON BODY.
USE TEFLON JOINT COMPOUND ON PLUG THREADS. CLEAN THE TOP OF
EXPOSED FCO AFTER INSTALLATION.
5
6
NONE
NONE
7
FLOOR CLEANOUT DETAIL
NONE
4"
CW OPTIONAL WATER
FEED FROM ABOVE
00/00/0000 00:00AM
NO:
DATE:
DRAWN BY:
BUILDING EXTERIOR
-DESCRIPTION:
REVIEWED BY:
OPERATING ROD AND CASING
LENGTH = WALL DEPTH + 2"
ACCESS PANEL
LOCATION BASED
ON PIPE FEED
3
HOSE
CONNECTION
4"
NOTES:
1.
2.
3.
4"
CW OPTIONAL WATER
FEED FROM ABOVE
GRADE
4.
5.
4"
UNION
COMPRESSOR
AND TANK
BB
ISSUED FOR:
CONSTRUCTION
DATE:
07.25.16
DRAWING NAME:
24"
MIN
EXPOSED PIPE SHALL HAVE
ESCUTCHEON TO COVER
PENETRATION.
SAFETY VALVE
FLEXIBLE
CONNECTION
PRESSURE RELIEF VALVE
SET FOR 50 P.S.I.
W/PRESSURE GAUGE
WALL BOX
UNION
SHUTOFF VALVE
3
PAV/DWM
10"
10"
3
FLPTH
--
2151374
BUILDING INTERIOR
6.
7.
I.P.S.
COMMENTS:
1. CENTER PIPE ALONG WITH THE INSULATION IN SLEEVE. CONTINUE THE
INSULATION THRU THE SLEEVE.
NONE
--
THICKNESS
WALL BOX
PIPE PENETRATION (NON-RATED WALL)
PAVEMENT
PER
DESIGN
DOCUMENTS
REVISIONS
INSULATED PIPE
9
EXPANSION JOINT TO
ENGINEER'S DETAILS
SEE NOTE 3
PROJECT NUMBER:
3
UNINSULATED PIPE
PROVIDE GALVANIZED STEEL PIPE
SLEEVE GROUTED INTO WALL.
CHEMICAL SYSTEM AT JANITOR'S SINK
WALL
PIPE OR CONDUIT
WALL CONSTRUCTION:
PRE-CAST, POURED IN
PLACE OR MASONRY
BLOCK
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
NONE
10"
STUD AND GYPSUM WALLBOARD
CONSTRUCTION: PROVIDE GALVANIZED
STEEL PIPE OR MINIMUM 18 GA
GALVANIZED SHEET METAL SLEEVE.
CAULK OR GROUT SLEEVE IN PLACE AS
REQUIRED.
8
MOP SINK DETAIL
FIRE STATION #2
2. THE DEDICATED WATER SUPPLY SHOULD NOT HAVE ANY BACKFLOW PREVENTION (E.G. NO
ATMOSPHERIC VACUUM BREAKER, ETC.), UNLESS REQUIRED BY THE LOCAL PLUMBING CODE OR
UTILITY- EACH CHEMICAL DISPENSER INCLUDES AN INTEGRAL BACKFLOW PREVENTOR ASSE 1055)
TO SANITARY MAIN.
3" SANITARY PIPING
SEE NOTE 4
PACK ANNULAR SPACE SOLID
WITH FIBERGLASS INSULATION
(FOR ACOUSTICS).
216 South Main Street,
Davidson, NC 28036
IT IS NECESSARY TO ENSURE MINIMUM DIMENSIONS SHOWN ARE SUITABLE FOR EXISTING
GROUND CONDITIONS. ENGINEERING ADVICE MAY BE REQUIRED.
MINIMUM CONCRETE STRENGTH OF 4,000 PSI IS RECOMMENDED. CONCRETE SHOULD BE
VIBRATED TO ELIMINATE AIR POCKETS.
EXPANSION AND CONTRACTION CONTROL JOINTS AND REINFORCEMENT ARE RECOMMENDED TO
PROTECT CHANNEL AND CONCRETE SURROUND. ENGINEERING ADVICE MAY BE REQUIRED.
THE FINISHED LEVEL OF THE CONCRETE SURROUND MUST BE APPROX. 1/8" [3mm] ABOVE THE
TOP OF THE CHANNEL EDGE.
CONCRETE BASE THICKNESS SHOULD MATCH SLAB THICKNESS. ENGINEERING ADVICE MAY BE
REQUIRED TO DETERMINE PROPER LOAD CLASS.
REFER TO ACO'S LATEST INSTALLATION INSTRUCTIONS FOR FURTHER DETAILS.
S200k - POWER DRAIN - LOAD CLASS: E
TO COMPRESSED
AIR LOOP
VIBRATION
ISOLATORS (TYP.
FOR 4)
MOISTURE AND OIL
SEPARATOR
DRAIN TO OUTSIDE OF BLDG.
FINISHED FLOOR
PLUMBING DETAILS
GATE VALVE
DRAWING NUMBER:
MECKLENBURG COUNTY
CODE ENFORCEMENT
10
NONE
FREEZE PROOF WALL HYDRANT DETAIL
11
NONE
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
TRENCH DRAIN DETAIL S200K POWERDRAIN
12
NONE
AIR COMPRESSOR DETAIL
P-502
L-1
LAVATORY
YES
KOHLER LEDENA K-2215
ADA 21" X 116-1/4"
SK-1
SINK - COUNTER
TOP DROP-IN
YES
KOHLER TOCCATA K-3346-4
FLOOR DRAIN
-
JOSAM
WCO
WALL CLEAN-OUT
-
JOSAM
MSB-1
MOP SINK
YES
FIAT TERRAZZO MOP SERVICE BASIN
TSBC6010
YES
FIAT MODEL LTD II WALL HUNG
SERV-A-SINK
SS-1
JOSAM 57000
FROST PROOF
HOSE BIB
YES
WOODFORD MB65-K
TP-1
TRAP PRIMER
YES
PRECISION P1-500
EYE WASH
TD-1
EYE WASH
TRENCH DRAIN
SYSTEM
YES
YES
BRADLEY S19314 SERIES
ACO DRAIN S200K, SK2-1:SK2-11
CB-1
CATCH BASIN
----
ACO DRAIN CATCH BASIN SK2-621D
LI-1
LINT
INTERCEPTOR
----
JOSAM MODEL 61806
SD-1
SINK DISPOSAL
---
GENERAL ELECTRIC
KITCHEN AID
WASTE KING
INSINKERATOR PR5O XL
C.W.
H.W.
WH-1
WH-2
LOCATION
MECHANICAL PLATFORM
TRUCK MEZZANINE
MANUFACTURER AND MODEL
RHEEM GHE80ES-130(A)
RHEEM GHE80ES-130(A)
WATER
CONNECTIONS
GAS INPUT
(BTUH)
2"
130,000
130,000
2"
THERM. EFF.
95%
95%
MOUNTING
FLUSH TANK
VITREOUS CHINA
HANDICAP
ELONGATED
-
-
-
-
FLOOR MTD
4"
2
1/2"
-
KOHLER K-7637-CP
FLOOR
UNDERCOUNTER
VITREOUS CHINA
RECTANGULAR
BASIN
KOHLER DM FAUCET
K-13467
STANDARD
SENSOR
SINGLE-HOLE
GRID
1-1/2"
1-1/2"
1/2"
1/2"
KOHLER K-8998 P-TRAP,
K-7129 DRAIN
DROP-IN
DOUBLE COMPT.
STAINLESS
6" DEEP 2-HOLE
KOHLER CORALAIS
K-15889-K
GOOSENECK
DOUBLE LEVER
8"
GRID
1-1/2"
1-1/2"
1/2"
1/2"
SURROUND
ENCLOSURE
W/BASE
FIBERGLASS
W./SANITARY
GELCOAT
HANDICAP
SHOWER
PACKAGE
K-10825-4
DEVONSHIRE
SHOWERING
PACKAGE
K-10591
MULTIFUNCTI
ON SHOWER
HEAD
SINGLE LEVER
K-304/K-P304
SERIES VALVE
ROUND TOP
CAST IRON
BRASS TOP
-
-
-
-
-
CAST IRON
-
-
-
-
MOP SINK
TERRAZZO
WITH PAIL
HOOK
FOUR ARM
SWING SPOUT
CP BLADE
HANDLES
4"
-
-
DOUBLE BOWL
LAUNDRY SINK
MOLDED STONE
ROUND TOP
CAST IRON
FLOOR MOUNTED
FIAT 830-AA FAUCET
MOP BASIN
WALL HUNG
CABINET
MOUNTED
FIAT A1 4" FAUCET
BRONZE PLUG
-
INTERGRAL
WALL-MOUNT
FRONT
WITH SLIDE
TRENCH
BAR & HOSE DRAIN W/.75
l-BAR-I GRATE
1/2"
1/2"
CAST IRON
SEE PLAN
-
-
-
-
FLOOR
PROVIDE: SEDIMENT BUCKET, TRAP PRIMER CONNECTION & VALVE
-
-
4"
-
-
-
-
WALL
-
8"
GRID
3"
2
1/2"
1/2"
-
FLOOR
INCLUDES STRAINER AND PLUG, CSA APPROVED. PROVIDE WITH 832-AA HOSE BRACKET, 889-CC MOP HANGER
AND E-77-A GUARD.
-
1/2"
1/2"
FLOOR
WALL MOUNTED STYLE - CABINET MOUNTED WITH , INCLUDES STRAINERS AND PLUGS.
2"
-
-
CAST IRON
4"
-
-
-
-
KEY
CYLINDER
LOCK
-
-
-
-
-
1/2 "
-
-
WALL
-
BRASS
-
-
-
-
-
-
-
-
1/2 "
-
-
-
FLOOR
MOUNTED
EYE/FACE
WASHDOWN
INFLOOR
W/EXTENSION
UNDER SINK
STAINLESS
-
-
POWER DRAIN
-
-
-
-
-
-
-
4"
2
TRENCH
4"
1
2
-
-
-
-
-
HWCP-1
HWCP-2
DOM HW RECIRCULATION
DOM HW RECIRCULATION
LOCATION
MANUFACTURER/MODEL
MECHANICAL
PLATFORM
TACO 4PC80/0012-F4-1
MEZZANINE
TACO 4PC8/0012-F4-1
HOUSING MATERIAL
BRONZE -LEAD FREE
BRONZE-LEAD FREE
FLOOR
-
-
-
-
-
CATCH BASIN
4"
2
-
-
PROVIDE FOUL AIR TRAP
GRAVITY DRAIN
-
-
-
-
-
4"
3" (2 REQ.)
-
-
-
-
SINK
MOUNTED
W/DISH
WASHER
DRAIN
1-1/2"
1-1/2"
-
-
1-1/2" TRAP
MULTI GRIND
COMMENTS
170
INSTALL PER MANUFACTURER'S
RECOMMENDATIONS
170
INSTALL PER MANUFACTURER'S
RECOMMENDATIONS
-
-
-
FIXTURE
48
48
VOLTS/PHASE/HZ
115/1/60
115/1/60
HP
QTY.
SIZE
GPH
KITCHEN SINK
1
5 GPH
5
MOP SINK
1
10 GPH
10
SHOWER
2
30 GPH
60
LAVATORY
2
5 GPH
10
1/8
1/8
FIXTURE
INSTALL PER
MANUFACTURER'S
RECOMMENDATIONS
INSTALL PER
MANUFACTURERS
RECOMMENDATIONS
SIZE
GPH
SERVICE SINK
1
5 GPH
5
MOP SINK
1
10 GPH
10
SHOWER
1
30 GPH
30
DOMESTIC WASHER
1
30 GPH
30
EQUIPMENT WASHER
1
30 GPH
30
LAVATORY
1
5 GPH
5
TOTAL REQUIRED FLOW AT 70°F TEMPERATURE RISE =
OF
ASSE 1011 SINGLE CHECK ANTI-SIPHON VACUUM BREAKER, MODULAR BOX SYSTEM
PISTON OPERATED, WILL PRIME 1 TO 4 FLOOR DRAINS, DISTRIBUTION UNIT DU-4/DU-U, INSTALL PER
MANUFACTURERS RECOMMENDATIONS.
SEAL
030515
EN
AI
E S S IO N
G INEER
G S. BL
EL
LA
A
I TE C TU R A
L
ES
C
CERT. NO.
52904
NO
CH
YT
ASSOCI AT
H
RC
AR
RT
H CAROLI
NA
L OT T E , N .
C
.
07/25/16
STANDARD DRAIN HEIGHT, 316 STAINLESS STEEL HANDLE, ANTI-FREEZE VALVE, HALO EYE/FACE WASH,
PROVIDE NAVIGATOR S19-2100 EFX25 EMERGENCY THERMOSTATIC MIXING VALVE FOR TEPID WATER.
© 2016 LaBella Associates
TOWN OF DAVIDSON
216 South Main Street,
Davidson, NC 28036
FOOD WASTE DISPOSER SHALL BE INSINKERATOR MODEL PRO EXCEL W/MULTIGRIND PLUS AND SOUNDSEAL
UNDER SINK PLUS TECHNOLOGIES, 1.0 HP MOTOR, AUTO-REVERSE GRIND SYSTEM FEATURE, STAINLESS STEEL GRIND
CHAMBER AND COMPONENTS. 1.0 HP/120V/60 HZ
SHOCK ABSORBER SCHEDULE
TAG
MANUFACTURER
MODEL
FIXTURE UNITS
INLET SIZE
SA-1
JAY R. SMITH
HYDROTOLS - 5005
1-11
3/4"
SA-2
JAY R. SMITH
HYDROTOLS - 5010
12-32
1"
SA-3
JAY R. SMITH
HYDROTOLS - 5020
33-60
1"
SA-4
JAY R. SMITH
HYDROTOLS - 5030
61-113
1"
SA-5
JAY R. SMITH
HYDROTOLS - 5040
114-154
1"
SA-6
JAY R. SMITH
HYDROTOLS - 5050
155-330
1"
85
QTY.
COMMENTS
H CARO L
I
RECESSED IN PROVIDE JOSAM 61806 SERIES LINT INTERCEPTOR W/ACID RESISTANT COATING, NON-SKID COVER, GALVANIZED
STEEL BUCKET W/SS SCREENS. PROVIDE WITH EXTENSION AS NEEDED.
FLOOR-
TRUCK BAY TANK WATER HEATER FLOW CALCULATIONS
MAX GPM @
HEAD
T
OR
PROVIDE WITH WATER TIGHT ABS PLUG
RECESSED IN PROVIDE GRATE, FOUL AIR TRAP, DEBRIS STRAINER, INSTALLATION DEVICE, GRATE REMOVAL TOOL, GRATE
SHALL BE IRON SLOTTED LONGITUDINAL, MODEL 72263 LOAD CLASS: E
FLOOR
LIVING AREA TANK WATER HEATER FLOW CALCULATIONS
GPH DELIVERED @
90 DEG F RISE
NC LICENSE NO. C-0430
PROVIDE CLOSING CAP PART NUMBER 96823, IRON SLOTTED LONGITUDINAL GRATE ADA COMPLIANT, SECURED
RECESSED IN
POWER LOK LOCKING OR APPROVED EQUAL. INSTALL TRENCH DRAIN SYSTEM PER MANUFACTURERS
FLOOR
RECOMMENDATIONS.
POWER DRAIN
PUMP SCHEDULE
SERVICE
FLOOR
-
TOTAL REQUIRED FLOW AT 70°F TEMPERATURE RISE =
TAG
WALL
2"
-
RECESSED IN
FLOOR
ADA COMPLIANT, DOUBLE COMPARTMENT, INCLUDES INSTALLATION HARDWARE, TOP - MOUNT. PROVIDE
K-15850-4M LEVER HANDLES WITH 1030920 SIDE SPRAY. SEE SD-1 ON SCHEDULE FOR DSPOSAL
3"
GRID
www.labellapc.com
0.5 GPM MAXIMUM FLOW-RATE, INCLUDES TWO AAA BATTERIES. PROVIDE 1139288 SPRAY AERATED. ADA
COMPLIANT, PROVIDE WITH TRUEBRO LAV GUARD UNDERSINK PIPING COVER MODEL #102 E-Z
REINFORCED POLYESTER RESIN SURROUND SHOWER ENCLOSURE AND BASE WITH GEL COAT, INTEGRAL FRONT
TRENCH DRAIN AND GRATE, HDPE FOLD-UP SEAT CURTAIN ROD, HORIZONTAL AND VERTICAL GRAB BARS,
KOHLER ADA SHOWER SYSTEM WITH HAND HELD SHOWER ASSEMBLY W/SLIDE ABR, VACUUM BREAKER &60"
HOSE. (ADA/ANSI). INSTALL PER OWNER RECOMMENDATIONS.
CHROME
RECESSED IN
FLOOR
TWO PIECE, K-4199 ELONGATED BOWL, K-4467-RZ TOILET FLUSH TANK, K-4731-C TOILET SEAT, 3/8" NPT
ANGLE SUPPLY WITH STOP AND ANNEALED VERTICLE TUBEBATTERIES. HIGH EFFICIENCY TOILET 1.28 GPF. ADA
COMPLIANT
MCGUIRE 175LK & PW8090 COUNTER TOP
-
POLYESTER
POLYMER
CONCRETE
POLYESTER
POLYMER
CONCRETE
STEEL w/ACID
RESISTANT
COATING
REMARKS
KOHLER K-304-CS VALE
WITH STOPS
GAS HOT WATER HEATER SCHEDULE
TAG
SUPPLIES & STOPS
CR
FPHB
VENT
R ATI ON
YES
SIZE
PO
FLOOR CLEAN
OUT
TYPE
AL
FCO
UTILITY SINK
JAY R. SMITH
WADE-TYLER
ZURN
JAY R. SMITH
WADE-TYLER
ZURN
ACORN TERRAZZO WARE
MUSTEE
SWAN STONE
ACORN TERRAZZO WARE
MUSTEE
SWANSTONE
JAY R. SMITH
WADE-TYLER
ZURN
JAY R. SMITH
WADE-TYLER
ZURN
JAY R. SMITH
WADE-TYLER
ZURN
ACORN SAFETY SHOWERS
JAY R. SMITH
GUARDIAN EQUIPMENT
JAY R. SMITH
ABT INC
MCNICHOLS INDUSTRIES
JAY R. SMITH
ABT INC
MCNICHOLS INDUSTRIES
JAY R. SMITH
WADE-TYLER
ZURN
CENTERS
OR
FD
HANDLES
C.
YES
SPOUT
P.
SHOWER
AQUA BATH
AQUARIUS BATHWARE
BEST BATH SYSTEMS
MANUFACTURER
MODEL NO.
NA
SH-1
COMFORT DESIGNS MODEL# XST
3838 TR RRF .75 L-BAR-I
AMERICAN STANDARD
GERBER
ZURN
AMERICAN STANDARD
GERBER
ZURN
ADVANCE TABCO
ELKAY
JUST
PIPING CONNECTIONS
DRAIN
B
KOHLER HIGHLINE K-3999-RZ-0
FLOOR MTD TANK TYPE
STYLE
LA
YES
MATERIAL
ED
WATER CLOSET
TYPE
R E GI S T E R
P-1
FAUCET/VALVE
OR APPROVED EQUAL BY ONE OF THE
FOLLOWING MANUFACTURERS
E
DESIGN MANUFACTURER & MODEL
H
ACCESSIBLE
N
DESCRIPTION
PR
FIXTURE
Engineering
Architecture
Environmental
Planning
455 South Main Street
Davidson, NC 28036
P: (704) 439-2931
PLUMBING FIXTURE SCHEDULE
FIRE STATION #2
19436 DAVIDSON CONCORD ROAD,
DAVIDSON, NC 28036
110
--
--
NO:
DATE:
-DESCRIPTION:
REVISIONS
PROJECT NUMBER:
2151374
DRAWN BY:
PAV/DWM
REVIEWED BY:
BB
ISSUED FOR:
CONSTRUCTION
DATE:
07.25.16
DRAWING NAME:
PLUMBING SCHEDULES
DRAWING NUMBER:
00/00/0000 00:00AM
FLPTH
MECKLENBURG COUNTY
CODE ENFORCEMENT
The Design In These Construction
Documents Have Been Reviewed For
Compliance With The State Building
Code. It Is The Responsibility Of The
Contractor To Construct This Project
With Good Engineering Practice And
In Compliance With The North
Carolina State Building Code.
P-601