advertisement
BEC 6300VNL
GigaConnect
®
Wireless Broadband Router
User Manual
Last revised: March, 2016
Version release: v1.2
TABLE OF CONTENTS
TABLE OF CONTENTS .................................... 2
CHAPTER 1: INTRODUCTION ......................... 1
NTRODUCTION TO YOUR
OUTER
.............................................................. 1
EATURES
PECIFICATIONS
.................................................................... 3
ARDWARE
PECIFICATIONS
..................................................................... 5
PPLICATION
IAGRAMS
......................................................................... 6
CHAPTER 2: PRODUCT OVERVIEW ............... 7
MPORTANT
OTE FOR
SING
HIS
OUTER
................................................ 7
ACKAGE
ONTENTS
............................................................................... 7
EVICE
ESCRIPTION
.............................................................................. 8
OWER
OURCE
.................................................................................. 11
YSTEM
ECOVERY
ROCEDURES
............................................................. 13
ABLING
............................................................................................ 14
CHAPTER 3: BASIC INSTALLATION ............. 15
ETWORK
ONFIGURATION
V
4 ......................................................... 16
Configuring PC in Windows Vista (IPv4) .......................................................... 20
ETWORK
ONFIGURATION
V
6 ......................................................... 24
Configuring PC in Windows Vista (IPv6) .......................................................... 28
EFAULT
ETTINGS
............................................................................... 31
NFORMATION FROM
OUR
ISP .............................................................. 32
CHAPTER 4: DEVICE CONFIGURATION ....... 33
OGIN TO YOUR
EVICE
......................................................................... 33
TATUS
.............................................................................................. 35
UICK
TART
...................................................................................... 49
ONFIGURATION
.................................................................................. 52
CHAPTER 5: TROUBLESHOOTING ............ 138
APPENDIX: PRODUCT SUPPORT & CONTACT
.......................................................................
TATEMENT
................................................................................ 141
EGULATIONS
................................................................................ 142
Introduction
1
C
HAPTER
1: I
NTRODUCTION
Introduction to your Router
Congratulations on your purchase of the
BEC 6300VNL (Wireless Broadband Router)
. This router is a compact and advanced broadband router that offers flexible and multiple Internet connection options, EWAN and embedded 3G/EVDO interfaces, for home, SOHO, and office users to enjoy highspeed, high-level security Internet connection via cellular wireless and/or Ethernet WAN. With an integrated 802.11n wireless access point and 4-port Gigabit Ethernet LAN, this router enables faster wireless speed of up to 300Mbps and LAN connection 10 times faster than regular 10/100Mbps
Ethernet LAN.
BEC 6300VNL (3G/EVDO Wireless Broadband Router)
provides a unique
Management Center enabling users to monitor 3G/EVDO signal strength, bandwidth, download speed, and many more.
Wireless Mobility and Security
With an integrated 802.11n Wireless Access Point, this router delivers up to 3 times the wireless coverage of a 802.11b/g network device, so that wireless access is available everywhere in the house or office. If your network requires wider coverage, the built-in Wireless Distribution System (WDS) allows you to expand your wireless network without additional wires or cables.
BEC 6300VNL
(3G/EVDO VoIP Wireless Broadband Router)
also supports the Wi-Fi Protected Setup (WPS) standard and allows users to establish a secure wireless network just by pressing a button. Multiple
SSIDs allow users to access different networks through a single access point. Network managers can assign different policies and functions for each SSID, increasing the flexibility and efficiency of the network infrastructure.
3G/EVDO Management Center
BEC 6300VNL (3G/EVDO VoIP Wireless Broadband Router)
Mobile Management Center visually displays its current 3G/EVDO signal status also calculates the total amount of hours or data traffic used per month, allowing you to manage your 3G/EVDO monthly subscriptions.
IPv6 Supported
Internet Protocol version 6 (IPv6) is a version of the Internet Protocol that is designed to succeed IPv4.
IPv6 has a vastly larger address space than IPv4. The router is already supporting IPv6, you can use it in IPv6 environment no need to change device. The dual-stack protocol implementation in an operating system is a fundamental IPv4-to-IPv6 transition technology. It implements IPv4 and IPv6 protocol stacks either independently or in a hybrid form. The hybrid form is commonly implemented in modern operating systems supporting IPv6.
Quick Start Wizard
Support a WEB GUI page to install this device quickly. With this wizard, simple steps will get you connected to the Internet immediately.
BEC 6300VNL User Manual
Firmware Upgradeable
Device can be upgraded to the latest firmware through the WEB based GUI.
Introduction
2
BEC 6300VNL User Manual
Introduction
Features & Specifications
3
Features & Specifications
• 3G/EVDO for mobile broadband connectivity
• Gigabit Ethernet WAN (GbE WAN) for Cable/Fiber/xDSL high WAN throughput
• Gigabit Ethernet LAN
• IPv6 ready (IPv4/IPv6 dual stack)
• Multiple wireless SSIDs with wireless guest access and client isolation
• IEEE 802.11 b/g/n compliant Wireless Access Point with Wi-Fi Protected Setup (WPS)
• Wi-Fi Protected Access (WPA-PSK/ WPA2-PSK) and Wired Equivalent Privacy (WEP)
• SOHO Firewall Security with DoS Preventing and Packet Filtering
• Quality of Service Control for traffic prioritization management
• Universal Plug and Play (UPnP) Compliance
• Ease of Use with Quick Installation Wizard
• One USB port for NAS (FTP/ SAMBA server)
• Ideal for SOHO, office, and home users
Network Protocols and Features
• IPv4, IPv6 or IPv4 / IPv6 Dual Stack
• NAT, static (v4/v6) routing and RIP-1 / 2
• DHCPv4 / v6
• Universal Plug and Play (UPnP) Compliant
• Dynamic Domain Name System (DDNS)
• Virtual Server and DMZ
• SNTP, DNS proxy
• IGMP snooping and IGMP proxy
• MLD snooping and MLD proxy
BEC 6300VNL User Manual
Introduction
Features & Specifications
4
Firewall
• Built-in NAT Firewall
• Stateful Packet Inspection (SPI)
• DoS attack prevention including Land Attack, Ping of Death, etc.
• Access control
• IP&MAC filter, URL Content Filter
• Password protection for system management
• VPN pass-through
Quality of Service Control
•Traffic prioritization management based-on Protocol, Port Number and IP Address (IPv4/ IPv6)
Wireless LAN
• Compliant with IEEE 802.11 b/ g/ n standards
• 2.4 GHz - 2.484GHz radio band for wireless
• Up to 300 Mbps wireless operation rate
• 64 / 128 bits WEP supported for encryption
• WPS (Wi-Fi Protected Setup) for easy setup
• Wireless Security with WPA-PSK / WPA2-PSK support
• WDS repeater function support
USB Application Server
• Storage/NAS: SAMBA Server, FTP Server
Management
• Quick Installation wizard
• Web-based GUI for remote and local management (IPv4/IPv6)
• Firmware upgrades and configuration data upload and download via web-based GUI
• Supports DHCP server / client / relay
• Supports SNMP v1, v2, v3, MIB-I and MIB-II
BEC 6300VNL User Manual
Introduction
Hardware
Specifications
5
Hardware Specifications
Physical interface
• Cellular antenna: 2 external antennas
• SIM card slot: Mini SIM card (2FF) slot for mobile broadband connectivity
• USB: USB 2.0 port for storage service
• Ethernet: 4-port 10 / 100 / 1000Mbps auto-crossover (MDI / MDI-X) Switch
• EWAN: RJ-45 Gigabit Ethernet port for connecting to Cable/Fiber/xDSL modem for Broadband connectivity.
• Factory default reset button
• Wireless on/off and WPS push button
• DC Power jack
• UPS Power with 4-pin connectors
• Power switch to switch between DC power and UPS power.
Physical Specifications
• Dimensions (W*H*D): 9.04" x 6.10" x 1.27"(229.5mm x 155mm x 32.24mm)
BEC 6300VNL User Manual
Introduction
Application Diagrams
6
Application Diagrams
BEC 6300VNL (3G/EVDO VoIP Wireless Broadband Router)
is an all-in-one router, supporting 2 connection options (3G/EVDO and EWAN) to connect to the Internet.
3G/EVDO router mode
With an embedded 3G/EVDO module, the router can be used to connect to high speed mobile fixed wireless connection.
Broadband Router Mode
This router also has a Gigabits Ethernet WAN port (EWAN) to connect with your Fiber / Cable/ xDSL modem.
BEC 6300VNL User Manual
Product Overview
7
C
HAPTER
2: P
RODUCT
O
VERVIEW
Important Note for Using This Router
Warning
Attention
Do not use the router in high humidity or high temperature.
Do not use the same power source for the BEC 6300VNL on other equipment.
Do not open or repair the case yourself. If the device becomes too hot, turn off the power immediately and have it repaired at a qualified service center.
Avoid using this product and all accessories outdoors.
Place the router on a stable surface.
Only use the power adapter that comes with the package.
Using a different voltage rating power adaptor may damage the router.
Package Contents
BEC 6300VNL 3G/EVDO VoIP Wireless Broadband Router x 1
Quick Start Guide x 1
RJ-45 Ethernet cable x 1
3G/EVDO detachable antennas x 2
DC Power adapter x 1
BEC 6300VNL User Manual
Device Description
Front Panel LEDs
Product Overview
Device Description / Front Panel LEDs
8
BEC 6300VNL User Manual
LED
Power
Battery
EWAN
Ethernet Port
LAN 1 ~ 3
USB 2.0
Wireless/WPS
Phone
LTE
(Received Signal
Strength
Indicator)
Internet
Product Overview
Device Description / Front Panel LEDs
STATUS DESCRIPTION
Green
Red
Green
System is up and ready
Boot failure
UPS is functioning properly
Orange UPS battery failure. Need a new battery replacement
Orange blinking UPS AC power failure and battery functioning properly
Off Device powered by the DC power adaptor
Lit up
Green
Orange
Blinking
Green
BEC 6300VNL is successfully connected with a broadband connection device.
Transmission speed is at Gigabit speed (1000Mbps)
Transmission speed is at 10/100Mbps
Data being transmitted/received
Transmission speed is at Gigabit speed (1000Mbps)
Orange
Blinking
Transmission speed is at 10/100Mbps
Data being transmitted/received
Green
Green
Connecting to a USB dongle or a hard drive.
Wireless connection established
Green blinking Data being transmitted / received
Orange WPS configuration is in progress
Green Successfully registered and ready to be used.
Orange
Green
Green
Flashing quickly
Orange
Flashing quickly
Orange
Flashing slowly
Orange
Off
Green
Red
Off
Phone is off-hook, in-use
RSSI greater than -69 dBm. Excellent signal condition
RSSI from -81 to -69 dBm. Good signal condition
RSSI from -99 to -81 dBm. Fair signal condition.
RSSI less than -99 dBm. Poor signal condition.
No signal and the 3G/EVDO module is in service
No 3G/EVDO module or 3G/EVDO module fails
IP connected and traffic is passing through the
IP request failed. device.
BEC 6300VNL is either in bridged mode or WAN connection not ready.
9
BEC 6300VNL User Manual
Rear Panel Connectors
Product Overview
Device Description / Rear Panel Connectors
10
1 3 4 5 6 7 8 1
1
1
2
9 1
0
PORT
1
2
LTE Antenna
3
SIM Card Slot
Phone (1X-2X)
MEANING
Screw the supplied LTE antennas onto the antenna connectors on both sides.
Insert the mini SIM card (2FF) with the gold contact facing down.
Push the mini SIM card (2FF) inwards to eject it
Connect your analog phone to this port with a RJ-11 cable.
4 USB
Connect an external USB dongle / hard drive for storage, network sharing, etc.
5
Gigabit
LAN Ethernet
(1~3)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps /100Mbps /1000Mbps
6
7
8
9
10
11
Gigabit EWAN
UPS Jack
Connect to Fiber/ Cable/ xDSL Modem with a RJ-45 cable
The 4-pin connectors are used to power the device with an external UPS battery backup.
Reset
WPS &
Wireless On/Off
Power Jack (DC)
After the device is powered on, press it the reset button for 10 seconds to restore to factory default settings (this is used when you cannot login to the router, e.g. forgot your password)
By controlling the pressing time, users can achieve two different effects:
(1) WPS
*
:
Press &hold the button for a few seconds to trigger WPS function.
(2) Wireless ON/OFF button
: Press & hold the button for 10 seconds to turn On/Off wireless.
* Please refer to the WPS section in the User Manual.
Connect the supplied Power Adapter to this jack.
Power Source
Power ON/OFF switch
(1) with Power Switch ON:
power up by the supplied DC power adaptor
(
2) with Power Switch OFF:
power up by the UPS battery unit
BEC 6300VNL User Manual
Product Overview
Power Source
11
Power Source
BEC 6300VNL offers two kinds of power input, namely,
DC power Adapter
and
DC UPS
(or BBU).
BEC 6300VNL can take the advantage of UPS (Uninterruptible Power Supply) to keep working even if the power outage hit your router when the router in working in DC UPS mode.
(A picture of the rear focusing on the power source)
UPS Port Assignment:
+12VDC: VCC (DC + 12V) Power supply
RTN: GND (Ground)
ALM 1: Active high – replace battery
ALM 2: Active high – on battery
(A shot from the front panel, with second icon being identified as the
Battery
LED)
How to switch between the two (2) power sources, DC power adaptor and external UPS battery
Pressed "Power Source" button, the button is visually being pressed down. The power source is from the DC power adapter supplied in the package.
BEC 6300VNL User Manual
Product Overview
Power Source
12
"Power Source" button in the un-pressed state, the power source is from the UPS. The router can continue to operate for a period of time after AC power failure, due to uninterrupted power system features of UPS.
UPS LED:
A Battery LED indicates if a DC UPS is in-use or not. When the router is operating via the DC power adapter this LED will be off.
Battery LED Definition:
Green LED: UPS AC power is working; UPS battery is also working well
Orange LED Only UPS AC power is working. Battery failure- need a new battery replacement
Orange LED: UPS AC power failure; UPS battery is working
BEC 6300VNL User Manual
System Recovery Procedures
Product Overview
System Recovery Procedures
13
The purpose is to allow users to restore the 6300VNL to its initial stage when the device is outage, upgraded to a wrong / broken firmware, cannot access to the GUI with wrong username and/or password, etc.
Step 1 – Configure your PC Network IP Address
Before performing the system recovery, assign this IP address and Netmask to your PC,
192.168.1.100
and
255.255.255.0
respectively.
Step 2 – Reset your 6300VNL Device
2.1
Power off your 6300VNL
2.2
Power on the 6300VNL while pushing the RESET button with a small pointed object (such as paper clip, needle, toothpick, etc.).
2.3
When the POWER LED turns RED, keep holding and pushing the RESET button until the
INTERNET LED flashes in GREEN
Step 3 – Restore your 6300VNL Device
When the INTERNET light flashes green, 6300VNL is in recovery mode and ready for a new
Firmware.
3.1 Open a web browser and type the IP address,
192.168.1.1
, to access to the recovery page.
NOTE
: In the recovery mode, 6300VNL will not respond to any PING or other requests.
3.2 Browse to the new Firmware image file then click Upload to start the upgrade process.
3.3 When the Internet LED turns red, the firmware upgrade is in process.
DO NOT power off or reboot the device, it would permanently damage your 6300VNL.
3.4 When the Internet LED turns green, the firmware upgrade is complete.
3.5 Power cycle on & off to regain access to the 6300VNL.
BEC 6300VNL User Manual
Product Overview
Cabling
14
Cabling
One of the most common causes of problems is bad cabling. Make sure that all connected devices are turned on. On the front panel of the product is a bank of LEDs. Verify that the LAN Link and LEDs are lit. If they are not, verify that you are using the proper cables.
Make sure that all other devices (e.g. telephones, fax machines, analogue modems) connected to the same telephone line as your BEC router have a line filter connected between them and the wall socket
(unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and that all line filters are correctly installed in a right way. If the line filter is not correctly installed and connected, it may cause problems to your connection or may result in frequent disconnections.
BEC 6300VNL User Manual
Basic Installation
15
C
HAPTER
3: B
ASIC
I
NSTALLATION
The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows XP / 7 / 8 / Vista, Linux, Mac OS, etc. The product provides an easy and user-friendly interface for configuration.
PCs must have an Ethernet interface installed properly and be connected to the router either directly or through an external repeater hub, and have TCP/IP installed or configured to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is
192.168.1.254
and the subnet mask is
255.255.255.0
(i.e. any attached PC must be in the same subnet, and have an IP address in the range of 192.168.1.1 to
192.168.1.253). The best and easiest way is to configure the PC to get an IP address automatically from the router using DHCP. If you encounter any problems accessing the router’s web interface it may also be advisable to
uninstall
any kind of software firewall on your PCs, as they can cause problems accessing the 192.168.1.254 IP address of the router. Users should make their own decisions on how to best protect their network.
Please follow the steps below for your PC’s network environment installation. First of all, please check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals.
Any TCP/IP capable workstation can be used to communicate with or through the
BEC 6300VNL
. To configure other types of workstations, please consult the manufacturer’s documentation.
BEC 6300VNL User Manual
Basic Installation
Network Configuration – Windows 10 (IPv4)
Network Configuration
– IPv4
16
Configuring PC in Windows 10 (IPv4)
1.
Click .
2.
Click
3.
Then click on
Network and Internet
.
4.
Under
Related settings,
select
Network and Sharing Center
5.
When the
Network and Sharing
Center
window pops up, select and click on
Change adapter settings
on the left window panel.
6.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
Basic Installation
Network Configuration – Windows 10 (IPv4)
7.
Select
Internet Protocol Version 4
(TCP/IPv4)
then click
Properties
.
17
8.
In the
TCP/IPv4 properties
window, select the
Obtain an IP address automatically
and
Obtain DNS
Server address automatically
radio buttons. Then click
OK
to exit the setting.
9.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Configuring PC in Windows 7/8 (IPv4)
1.
Go to
Start
. Click on
Control Panel
.
2.
Then click on
Network and Internet
.
Basic Installation
Windows 7/8 (IPv4)
18
3.
When the
Network and Sharing
Center
window pops up, select and click on
Change adapter settings
on the left window panel.
4.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
5.
Select
Internet Protocol Version 4
(TCP/IPv4)
then click
Properties
.
Basic Installation
Windows 7/8 (IPv4)
19
6.
In the
TCP/IPv4 properties
window, select the
Obtain an IP address automatically
and
Obtain DNS
Server address automatically
radio buttons. Then click
OK
to exit the setting.
7.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Configuring PC in Windows Vista (IPv4)
1.
Go to
Start
. Click on
Network
.
2.
Then click on
Network and Sharing
Center
at the top bar.
Basic Installation
Windows Vista (IPv4)
20
3.
When the
Network and Sharing
Center
window pops up, select and click on
Manage network connections
on the left window pane.
4.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
5.
Select
Internet Protocol Version 4
(TCP/IPv4)
then click
Properties
.
Basic Installation
Windows Vista (IPv4)
21
6.
In the
TCP/IPv4 properties
window, select the Obtain an
IP address automatically
and
Obtain DNS Server address automatically
radio buttons.
Then click
OK
to exit the setting.
7.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Configuring PC in Windows XP (IPv4)
1.
Go to
Start
. Click on
Control Panel.
2.
Then click on
Network and Internet
.
Basic Installation
Windows XP (IPv4)
22
3.
In the
Local Area Connection Status
window, click
Properties
.
4.
Select
Internet Protocol (TCP/IP)
and click
Properties
.
BEC 6300VNL User Manual
5.
Select the
Obtain an IP address automatically
and the
Obtain DNS server address automatically
radio buttons.
6.
Click
OK
to finish the configuration.
Basic Installation
Windows XP (IPv4)
23
BEC 6300VNL User Manual
Network Configuration
– IPv6
Configuring PC in Windows 10 (IPv6)
1.
Click .
2.
Click
3.
Then click on
Network and Internet
.
4.
Under
Related settings,
select
Network and Sharing Center
5.
When the
Network and Sharing
Center
window pops up, select and click on
Change adapter settings
on the left window panel.
Basic Installation
Windows 10 (IPv6)
24
6.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
7.
Select
Internet Protocol Version 6
(TCP/IPv6)
then click
Properties
.
Basic Installation
Windows 10 (IPv6)
25
8.
In the
TCP/IPv6 properties
window, select the
Obtain an IPv6 address automatically
and
Obtain DNS
Server address automatically
radio buttons. Then click
OK
to exit the setting.
9.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Configuring PC in Windows 7/8 (IPv6)
1.
Go to
Start
. Click on
Control Panel
.
2.
Then click on
Network and Internet
.
Basic Installation
Windows 7/8 (IPv6)
26
3.
When the
Network and Sharing
Center
window pops up, select and click on
Change adapter settings
on the left window panel.
4.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
5.
Select
Internet Protocol Version 6
(TCP/IPv6)
then click
Properties
.
Basic Installation
Windows 7/8 (IPv6)
27
6.
In the
TCP/IPv6 properties
window, select the
Obtain an IPv6 address automatically
and
Obtain DNS
Server address automatically
radio buttons. Then click
OK
to exit the setting.
7.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Basic Installation
Network Configuration – Windows Vista (IPv6)
Configuring PC in Windows Vista (IPv6)
28
1.
Go to
Start
. Click on
Network
.
2.
Then click on
Network and Sharing
Center
at the top bar.
3.
When the
Network and Sharing
Center
window pops up, select and click on
Manage network connections
on the left window pane.
4.
Select the
Local Area Connection
, and right click the icon to select
Properties
.
BEC 6300VNL User Manual
Basic Installation
Network Configuration – Windows Vista (IPv6)
5.
Select
Internet Protocol Version 6
(TCP/IPv6)
then click
Properties
.
29
6.
In the
TCP/IPv6 properties
window, select the Obtain an
IP address automatically
and
Obtain DNS Server address automatically
radio buttons.
Then click
OK
to exit the setting.
7.
Click
OK
again in the
Local Area
Connection Properties
window to apply the new configuration.
BEC 6300VNL User Manual
Basic Installation
Network Configuration – Windows XP (IPv6)
Configuring PC in Windows XP (IPv6)
30
IPv6 is supported by Windows XP, but you need to install it first.
Please follow the steps to install IPv6:
1. On the Desktop, Click
Start
>
Run
, type
cmd
, then press
Enter
key in the keyboard, the following screen appears.
2. Key in command
ipv6 install
Installation of IPv6 is now completed. Test it to see if it can work.
BEC 6300VNL User Manual
Basic Installation
Default Settings
31
Default Settings
Before configuring the router, you need to know the following default settings.
Web Interface: (Username and Password)
Username: admin
Password: admin
The default username and password are “
admin
” and “
admin
” respectively.
Attention
If you ever forget the username/password to login to the router, you may press the RESET button up to 6 seconds then release it to restore the factory default settings.
Caution
: After pressing the RESET button for more than 6 seconds then release it, to be sure you power cycle the device again.
Device LAN IP Settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
DHCP Server:
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
BEC 6300VNL User Manual
Basic Installation
Information from Your ISP
32
Information from Your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as
EWAN
((Dynamic IP address, Static IP address, PPPoE, Bridge Mode).
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
Username, Password, Service Name, and Domain Name
System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).
Dynamic IP Address
Static IP Address
DHCP Client (it can be automatically assigned by your ISP when you connect or be set manually).
IP address, Subnet mask, Gateway address, and Domain Name
System (DNS) IP address (it is fixed IP address).
Pure Bridge
Bridge Mode
BEC 6300VNL User Manual
Device Configuration
Login to GUI
C
HAPTER
4: D
EVICE
C
ONFIGURATION
33
Login to your Device
Open your web browser, enter the IP address of your router, which by default is
192.168.1.254
, and click “
Go
”, a user name and password window prompt appears.
The default username and password is
“admin”
and
“admin”
respectively for the
Administrator.
NOTE: This username / password may vary by different Internet Service Providers.
Congratulations! You have successfully logged on to your BEC 6300VNL.
BEC 6300VNL User Manual
Device Configuration
Login to GUI
34
Once you have logged on to your 6300VNL via your web browser, you can begin to set it up according to your requirements. On the configuration homepage, the left navigation pane links you directly to the setup pages, which includes:
Section Status
Quick Start
(Wizard
Setup)
Configuration Language
Sub-
Items
Device Info
System Status
System Log
3G/4G-LTE
Status
Statistics
DHCP Table
Disk Status
VoIP Status
-
-
VoIP Status
VoIP Call Log
Interface Setup
-
Internet
-
LAN
-
Wireless
-
Wireless MAC Filter
Advanced Setup
-
Firewall
-
Routing
-
NAT
-
Static DNS
-
QoS
-
Interface Grouping
-
Time Schedule
VoIP
-
Basic
-
Media
-
Advanced
-
Speed Dial
-
Dial Plan
-
Call Features
-
NAT Traversal
Access Management
-
Device Management
-
SNMP
-
Remote Syslog
-
Universal Plug & Play (UPnP)
-
Dynamic DNS
-
Access Control
-
Packet Filter
-
CWMP (TR-069)
-
Parental Control
-
SAMBA & FTP Server
Maintenance
-
User Management
-
Time Zone
-
Firmware & Configuration
-
System Restart
-
Auto Reboot
-
Diagnostic Tool
Please see the relevant sections of this manual for detailed instructions on how to configure your
BEC 6300VNL
gateway.
BEC 6300VNL User Manual
Device Configuration
Status
35
Status
In this section, you can check the router working status, including
Device Info
,
System Log
,
3G/4G-
LTE Status, Statistics
,
DHCP Table, Disk Status
, and
VoIP Status
.
BEC 6300VNL User Manual
Device Info
It contains basic information of the device.
Device Configuration
Status
–
Device Info
36
Device Information
Model Name:
Name of the router for identification purpose.
Firmware Version:
Software version currently loaded in the router
MAC Address:
A unique number that identifies the router
LAN
IPv4 :
IP Address:
LAN port IPv4 address.
Subnet Mask:
LAN port IP subnet mask.
DHCPv4 Server:
LAN port DHCP role - Enabled, Relay or Disabled.
IPv6 :
BEC 6300VNL User Manual
Device Configuration
Status
–
Device Info
37
IP Address:
LAN port IPv6 address.
Prefix Length:
The prefix length
DHCPv6 Server:
The DHCP status.
WAN
Interface:
WAN connection options, "EWAN" or "3G/4G-LTE".
Service:
The WAN interface service index.
PPP Connection Time
: the uptime of the PPP connection.
IPv4:
Status:
The connection status, either being connected or not in connected.
IP Address:
WAN port IP address.
Subnet Mask:
WAN port IP subnet mask.
Default Gateway:
The IP address of the default gateway.
DNS Server:
DNS information.
IPv6:
Status:
The IPv6 connection status.
IP Address:
WAN port IPv6 address.
Prefix Length:
The prefix length of IPv6 address.
Default Gateway:
The IP address of the default gateway.
DNS Server:
DNS information.
3G/4G-LTE:
Signal Strength:
The signal strength bar and dBm value indicates the current 3G/4G-LTE signal strength. The front panel 3G/4G-LTE Signal Strength LED indicates the signal strength as well.
Network Name:
The name of the LTE network the router is connecting to.
Card IMEI:
The unique identification number that is used to identify the 3G/4G-LTE module.
Card IMSI:
The international mobile subscriber identity used to uniquely identify the 3G/4G-LTE module.
BEC 6300VNL User Manual
Device Configuration
Status
–
System Status & System Log
38
System Status
System status displays the current router system (CPU and Memory) usage.
System Log
In system log, you can check the operations status and any glitches to the router.
Refresh:
Press this button to refresh the statistics.
BEC 6300VNL User Manual
3G/4G-LTE Status
This page contains 3G/4G-LTE connection information.
Device Configuration
Status
–
3G/4G-LTE Status
39
Status:
The current status of the 3G/4G-LTE connection.
Signal Strength:
The signal strength bar and dBm value indicates the current 3G/4G-LTE signal strength. The front panel 3G/4G-LTE Signal Strength LED indicates the signal strength as well.
Signal Information:
Shows important LTE signal parameters such as RSRP (
Reference Signal
Receiving Power), RSRQ (Reference Signal Receiving Quality), SINR (Signal to Interference plus
Noise Ratio).
RSRP (
Reference Signal Receiving Power): is the average power of all resource elements which carry cell-specified reference signals over the entire bandwidth.
RSRQ (Reference Signal Receiving Quality): measures the signal strength and is calculated based on both RSRP and RSSI.
RSSI (Received Signal Strength Indicator): parameter which provides information about total received wide-band power (measure in all symbols) including all interference and thermal noise.
SNR (Signal Noise Ratio): is also a measure of signal quality as well. It is widely used by the operators as it provides a clear relationship between RF conditions and throughput.
Note:
Some LTE modules do not provide this information.
Network Name:
The name of the LTE network the router is connecting to.
Cell ID:
The ID of base station that the device is connected to.
Card IMEI:
The unique identification number that is used to identify the 3G/4G-LTE module.
Card IMSI:
The international mobile subscriber identity used to uniquely identify the 3G/4G-LTE module.
Network Mode:
Display current network operating mode.
Network Band:
Indicated the current radio frequency band used.
Refresh:
Press this button to refresh the statistics.
BEC 6300VNL User Manual
Statistics
EWAN
Device Configuration
Status
–
Statistics
(
EWAN)
40
Interface:
List all available network interfaces in the router. You are currently checking on the physical status of the
EWAN
port
.
Transmit Frames:
This field displays the total number of frames transmitted until the latest second.
Transmit Multicast Frames:
This field displays the total number of multicast frames transmitted till the latest second.
Transmit Total Bytes:
This field displays the total number of bytes transmitted until the latest second.
Transmit Collision:
This is the number of collisions on this port.
Transmit Error Frames:
This field displays the number of error packets on this port.
Receive Frames:
This field displays the number of frames received until the latest second.
Receive Multicast Frames:
This field displays the number of multicast frames received until the latest second.
Receive Total Bytes:
This field displays the number of bytes received until the latest second.
Receive CRC Errors:
This field displays the number of error packets on this port.
Receive Under-size Frames:
This field displays the number of under-size frames received until the latest second.
Refresh:
Press this button to refresh the statistics.
BEC 6300VNL User Manual
Device Configuration
Status
–
Statistics
(
3G/4G_LTE)
3G/4G-LTE
Take 3G/4G-LTE as an example to describe the following connection transmission information.
41
Interface:
List all available network interfaces in the router. You are currently checking on the physical status of
3G/4G-LTE
interface
.
Transmit Frames of Current Connection:
This field displays the total number of 3G/4G-LTE frames transmitted until the latest second for the current connection.
Transmit Bytes of Current Connection:
This field shows the total bytes transmitted till the latest second for the current connection for the current connection.
Transmit Total Frames:
The field displays the total number of frames transmitted till the latest second since system is up.
Transmit Total Bytes:
This field displays the total number of bytes transmitted until the latest second since system is up.
Receive Frames of Current Connection:
This field displays the number of frames received until the latest second for the current connection.
Receive Bytes of Current Connection:
This field shows the total bytes received till the latest second for the current connection.
Receive Total Frames:
This field displays the total number of frames received until the latest second since system is up.
Receive Total Bytes:
This field displays the total frames received till the latest second since system is up.
BEC 6300VNL User Manual
Ethernet
Device Configuration
Status
–
Statistics
(
Ethernet)
42
Interface:
List all available network interfaces in the router. You are currently checking on the physical status of the
Ethernet
port
.
Transmit Frames:
This field displays the number of frames transmitted until the latest second.
Transmit Multicast Frames:
This field displays the number of multicast frames transmitted until the latest second.
Transmit Total Bytes:
This field displays the number of bytes transmitted until the latest second.
Transmit Collision:
This is the number of collisions on this port.
Transmit Error Frames:
This field displays the number of error packets on this port.
Receive Frames:
This field displays the number of frames received until the latest second.
Receive Multicast Frames:
This field displays the number of multicast frames received until the latest second.
Receive Total Bytes:
This field displays the number of bytes received until the latest second.
Receive CRC Errors:
This field displays the number of error packets on this port.
Receive Under-size Frames:
This field displays the number of under-size frames received until the latest second.
Refresh:
Press this button to refresh the statistics.
BEC 6300VNL User Manual
Wireless
Device Configuration
Status
–
Statistics
(
Wireless)
43
Interface:
List all available network interfaces in the router. You are currently checking on the physical status of the
Wireless.
Transmit Frames:
This field displays the number of frames transmitted until the latest second.
Transmit Error Frames:
This field displays the number of error frames transmitted until the latest second.
Transmit Drop Frames:
This field displays the number of drop frames transmitted until the latest second.
Receive Frames:
This field displays the number of frames received until the latest second .
Receive Error Frames:
This field displays the number of error frames received until the latest second.
Receive Drop Frames:
This field displays the number of drop frames received until the latest second.
Refresh:
Press this button to refresh the statistics.
BEC 6300VNL User Manual
Device Configuration
DHCP & Disk Status
44
DHCP Table
DHCP table displays the devices connected to the router with clear information.
Index #:
The index identifying the connected devices.
Host Name:
Show the hostname of the PC.
IP Address:
The IP allocated to the device.
MAC Address: T
he MAC of the connected device.
Expire Time:
The total remaining interval since the IP assignment to the PC.
Disk Status
Partition:
Display the USB storage partition.
Disk Space (KB):
Display the total storage space of the NAS in Kbytes unit.
Free Space (KB):
Display the available space in Kbytes unit.
BEC 6300VNL User Manual
Device Configuration
Status – IPSec Status
45
IPSec Status
Index #:
The numeric IPSec tunnel indicator.
Action:
Connect or Drop the connection.
Connection Name:
User-defined IPSec VPN connection name.
Active:
Show if the tunnel is active for connection.
Connection State:
Show the IPSec phase 1 and phase 2 connecting status.
Statistics:
Display the upstream/downstream traffic per session in KB. The value clears when session disconnects.
Remote Gateway:
The IP of the remote IPSec gateway.
Remote Network:
The IP and Netmask of remote access range.
Local Network:
The IP and Netmask of local access range.
BEC 6300VNL User Manual
Device Configuration
Status – PPTP Status
46
PPTP Status
PPTP Server
Index #:
The numeric PPTP connection indicator.
Connection Name:
Show user-defined PPTP VPN connection name.
Active:
Show if the tunnel is active for connection.
Connection State:
Show the connecting status.
Connection Type:
Remote Access or LAN to LAN.
Assigned IP Address:
Show the IP assigned to the client by PPTP Server.
Remote Network:
Display the remote network and subnet mask in LAN to LAN PPTP connection.
Refresh:
Click this button to refresh the connection status.
PPTP Client
Index #:
The numeric PPTP connection indicator.
Connection Name:
Show user-defined PPTP VPN connection name.
Active:
Show if the tunnel is active for connection.
Connection State:
Show the connecting status.
Connection Type:
Remote Access or LAN to LAN.
Server IP Address:
Show the IP of remote PPTP Server.
Remote Network:
Display the remote network and subnet mask in LAN to LAN PPTP connection.
Refresh:
Click this button to refresh the connection status.
BEC 6300VNL User Manual
Device Configuration
Status – PPTP Status
47
L2TP Status
Index #:
The numeric L2TP tunnel indicator.
Connection Name:
Display the user-defined L2TP connection name.
Active:
Show if the tunnel is active for connection.
Connection State:
Show the connecting status.
Connection Mode:
The L2TP mode is dial-in or dial-out.
Connection Type:
Remote Access or LAN to LAN.
Tunnel Remote IP Address:
Display the remote tunnel IP address.
Refresh:
Click this button to refresh the connection status.
GRE Status
Index #:
The numerical GRE tunnel indication.
Connection Name:
Display the user-defined GRE connection name.
Active:
Show if the tunnel is active for connection.
Connection State:
Show the connecting status.
Remote Gateway IP:
The IP of the remote GRE gateway.
Remote Network:
Display the remote network.
BEC 6300VNL User Manual
Device Configuration
VoIP Status
48
VoIP Status
VoIP Status
VoIP status gives you a directive picture on the registered VoIP accounts.
Phone Number:
The number you use to register in the Basic page of VoIP.
Host:
Show the IP address and port number of SIP Registrar.
Status:
The status of the registered SIP account.
Registered Time:
The duration the account has been successfully registered to the SIP registrar.
VoIP Call Log
VoIP call log records all inbound / outbound calls in details within your VoIP accounts. You can quickly view the call date, time, incoming/outgoing/missed call telephone number, and more.
Phone Number:
The number you use to register in the Basic page of VoIP.
Incoming / Outgoing / Miss Call Log:
Click the call log you want to view.
Start-Time:
The start time of the call
Caller/Called Name:
Display the caller ID of the dialing party / the party you dialed to reach to.
Caller/Called Number:
Display caller telephone number / telephone number you dialed to reach to
Answer Time:
The answer time of phone call
End Time:
The end time of the call
Talk Duration:
Time duration of individual calls from dial/call to hang-up.
Status:
Current call status if phones are off hook or in a call.
BEC 6300VNL User Manual
Device Configuration
Quick Start
49
Quick Start
This is a useful and easy utility to help you to setup the router quickly and to connect to your ISP
(Internet Service Provider) with only a few steps. It will guide you step by step to setup time zone and WAN settings of your device. The Quick Start Wizard is a helpful guide for the first-time users to the device.
For detailed instructions on configuring WAN settings, see refer to the
Interface Setup
section.
Click
NEXT
to move on to Step 1.
Step 1 – Password
Set new password of the “admin” account to access for router management. The default is “admin”.
Once changed, please use this new password next time when accessing to the router. Click
NEXT
to continue.
Step 2 – Time Zone
Choose your time zone. Click
NEXT
to continue.
BEC 6300VNL User Manual
Device Configuration
Quick Start
50
Step 3 – Wireless
Set up your wireless connection if you want to connect to the Internet wirelessly on your PCs. Click
NEXT
to continue.
Step 4 – ISP Connection Type
Set up your Internet connection.
4.1
Select an appropriate WAN connection protocol then click
NEXT
to continue.
4.2
If selected
3G/4G-LTE
(for example).
Input all relevant 3G/4G-LTE parameters from your ISP.
BEC 6300VNL User Manual
Device Configuration
Quick Start
51
Click Next to save changes.
4.2
If selected
EWAN / PPPoE
, please enter PPPoE account information provided by your ISP. Click
NEXT
to continue .
Step 5 – Quick Start Completed
The Setup Wizard has completed. Click on BACK to modify changes or mistakes. Click
NEXT
to save the current settings.
Switch to
Status > Device Info
to view the status.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet
52
Configuration
Click to access and configure the available features in the following:
Interface Setup, Advanced
Setup, VoIP, Access Management,
and
Maintenance.
These functions are described in the following sections.
Interface Setup
Here are the features under
Interface Setup: Internet
,
LAN
,
Wireless
and
Wireless MAC Filter
.
BEC 6300VNL User Manual
Internet
EWAN
Device Configuration
Interface Setup – Internet (EWAN)
53
Multi Service
Service Index:
The index marks the EWAN interface of different ISP type, ranging from 0-7.
Service Summary:
The overall service information.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet (EWAN)
54
Status:
Select whether to enable the service.
IPv4/IPv6
IP Version:
Choose
IPv4, IPv4/IPv6, IPv6
based on your environment. If you don’t know which one to choose from, please choose IPv4/IPv6 instead.
ISP Connection Type:
ISP:
Select the encapsulation type your ISP uses.
Dynamic IP:
Select this option if your ISP provides you an IP address automatically.
Static IP:
Select this option to set static IP information. You will need to enter in the Connection type, IP address, subnet mask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form. IP address from by four IP octets separated by a dot (xx.xx.xx.xx). The Router will not accept the IP address if it is not in this format.
PPPoE:
Select this option if your ISP requires you to use a PPPoE connection.
Bridge:
Select this mode if you want to use this device as an OSI Layer 2 device like a switch.
802.1q Options
802.1q:
When activated, please enter a VLAN ID.
VLAN ID:
It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN ID identification, tagged: 0-4095.
PPPoE (If selected PPPoE as WAN Connection Type; otherwise, skip this part)
Username:
Enter the user name provided by your ISP.
Password:
Enter the password provided by your ISP.
Bridge Interface for PPPoE:
When “Activated”, the device will gain WAN IP from your ISP with the
PPPoE account. But if your PC is connected to the router working as a DHCP client, in this mode, the
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet (EWAN)
55
device acts as a NAT router; while if you dial up with the account within your PC, the device will then work as a bridge forwarding the PPPoE information to the PPPoE server and send the response to your PC, thus your PC gets a WAN IP working in the internet.
Connection Setting
Connection:
Always On:
Click on
Always On
to establish a PPPoE session during start up and to automatically re-establish the PPPoE session when disconnected by the ISP.
Connect Manually:
Select Connect Manually when you don't want the connection up all the time.
TCP MSS Option:
Enter the maximum size of the data that TCP can send in a segment. Maximum
Segment Size (MSS).
IP Common Options
Default Route:
Select
Yes
to use this interface as default route interface.
TCP MTU Option:
Enter the maximum packet that can be transmitted. Default MTU
0
means it is set to 1492 bytes.
IPv4 Options
Get IP Address:
Choose Static or Dynamic
Static IP Address:
If
Static
is selected in the above field, please enter the specific IP address you get from ISP and the following IP subnet mask and gateway address.
IP Subnet Mask:
The default is 0.0.0.0. User can change it to other such as 255.255.255.0.Type the subnet mask assigned to you by your ISP (if given).
Gateway:
Enter the specific gateway IP address you get from ISP.
NAT:
Select Enable if you use this router to hold a group of PCs to get access to the internet.
Dynamic Route:
RIP Version:
(Routing Information protocol) Select this option to specify the RIP version, including RIP-1, RIP-2.
RIP Direction:
Select this option to specify the RIP direction.
-
None
is for disabling the RIP function.
-
Both
means the router will periodically send routing information and accept routing information then incorporate into routing table.
-
IN only
means the router will only accept but will not send RIP packet.
-
OUT only
means the router will only send but will not accept RIP packet.
IGMP Proxy:
IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group. Choose whether enable IGMP proxy.
IPv6 options
(only when choose IPv4/IPv6 or just IPv6 in IP version field above):
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet (EWAN)
IPv6 Address:
Type the WAN IPv6 address from your ISP.
Obtain IPv6 DNS:
Choose if you want to obtain DNS automatically.
56
Primary/Secondary:
if you choose Disable in the Obtain IPv6 DNS field, please type the exactly primary and secondary DNS.
MLD Proxy:
MLD (Multicast Listener Discovery Protocol) is to IPv6 just as IGMP to IPv4. It is a
Multicast Management protocol for IPv6 multicast packets.
When router’s Internet configuration is finished successfully, you can go to status to get the connection information.
BEC 6300VNL User Manual
3G/4G-LTE
Device Configuration
Interface Setup – Internet (3G/4G_LTE)
57
Status:
Choose Activated to enable the 3G/EVDO service.
IP Pass-Through Mode:
When
enabled
, BEC 6300VNL is in bridge mode and will not obtain a WAN
IP address, features such as routing capabilities, NAT, firewall, etc., will be disabled by default.
However, the client router behind the BEC 6300VNL can get a WAN IP address instead.
When
disabled
, BEC 6300VNL is in router mode that it handles a WAN IP address and all routingrelated features become available.
LTE Mode (
This feature is not supported in some LTE modules)
:
Display current selected LTE frequency band. To change the band, please click “
LTE Band
” to access to the band selection page.
LTE Band
LTE Band:
A list of available LTE bands to choose from.
LTE Antenna Diversity (
This feature is not supported in some LTE modules)
:
When
enabled
, the auxiliary antenna will be activated. With
disabled
, only the primary antenna is receiving and transmitting data.
To change it, please click “
LTE Antenna Diversity
” to access to the LTE antenna diversity selection page.
NOTE:
When using Yagi antenna, please DISABLE the Antenna Diversity feature for utmost performance.
LTE Antenna Diversity
To enable or disable the LTE antenna diversity feature.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet (3G/4G_LTE)
58
PLMN (Public Land Mobile Network) Selection:
TEL No.:
The dial string to make a GPRS / 3G/4G-LTE user internetworking call. It may provide by your mobile service provider.
Dual APN:
BEC 6300VNL can support up to two (2) APNs. Select Single or Dual.
APN:
An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS call. The service provider is able to attach anything to an APN to create a data connection, requirements for
APNs varies between different service providers. Most service providers have an internet portal which they use to connect to a DHCP Server, thus giving you access to the internet i.e. some 3G operators use the APN ‘internet’ for their portal. The default value is “internet”.
Username/Password:
Enter the username and password provided by your service provider. The username and password are case sensitive.
PIN:
PIN stands for Personal Identification Number. A PIN code is a numeric value used in certain systems as a password to gain access, and authenticate. In mobile phones a PIN code locks the SIM card until you enter the correct code. If you enter the PIN code incorrectly into the phone 3 times in a row, then the SIM card will be blocked and you will require a PUK code from your network/service provider.
Connection:
Default set to Always on to keep an always-on 3G/4G-LTE connection.
Keep Alive:
Select
Yes
to keep the 3G/4G-LTE connection always on.
Keep Alive IP:
Enter the IP address that the router can ping the IP to find whether the connection is on or not, if not, router will recover the connection.
Default Route:
Select
Yes
to use this interface as default route interface.
NAT:
Select this option to Disabled/Enable the NAT (Network Address Translation) function. Enable
NAT to grant multiples devices in LAN to access to the Internet through a single WAN IP.
SMS Control:
Enable to send a SMS message to reboot or get the current 3G/ 4G LTE status information from the 6300VNL.
NOTE:
You must obtain the phone number on the SIM card. Please contact with your network / service provider for more information.
SMS Control
SMS Control:
Check to enable this feature.
Control Password:
Pre-config a password to automatically reboot 6300VNL via a SMS message.
Password length is up to 10 characters. (Valid characters: 0~9, A~Z and a~z)
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Internet (3G/4G_LTE)
59
Example:
6300VNL obtains the phone number, +513 123 4567, on the SIM card
1. Send a text message,
reboot#
<password> , to +513 123 4567. 6300VNL will reboot the system upon receiving of this text message.
2. Send a text message,
*60
, to +513 123 4567. 6300VNL will send the current 3G/ 4G status information back including IMEI number, System up time, Network mode, Signal strength, WAN IP, and Connection time.
When router’s Internet configuration is finished successfully, you can go to the
Status
to check connection information.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – LAN
LAN
A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building.
60
IPv4 Parameters
IP Address:
Enter the IP address of Router in dotted decimal notation, for example, 192.168.1.254
(factory default).
IP Subnet Mask:
The default is 255.255.255.0. User can change it to other such as 255.255.255.128.
Alias IP Address:
This is for local networks virtual IP interface. Specify an IP address on this virtual interface.
Alias IP Subnet Mask:
Specify a subnet mask on this virtual interface.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – LAN
61
IGMP Snooping:
Select
Activated
to enable IGMP Snooping function, Without IGMP snooping, multicast traffic is treated in the same manner as broadcast traffic - that is, it is forwarded to all ports.
With IGMP snooping, multicast traffic of a group is only forwarded to ports that have members of that group.
Dynamic Route:
RIP Version:
(Routing Information protocol) Select this option to specify the RIP version, including RIP-1, RIP-2.
RIP Direction:
Select this option to specify the RIP direction.
-
None
is for disabling the RIP function.
-
Both
means the router will periodically send routing information and accept routing information then incorporate into routing table.
-
IN only
means the router will only accept but will not send RIP packet.
-
OUT only
means the router will only send but will not accept RIP packet.
DHCPv4 Server
DHCP (Dynamic Host Configuration Protocol) allows individual clients to obtain TCP/IP configuration at start-up from a server.
DHCPv4 Server:
If set to
Enabled
, your BEC 6300VNL can assign IP addresses, default gateway and DNS servers to the DHCP client.
If set to
Disabled
, the DHCP server will be disabled.
If set to
Relay
, the BEC 6300VNL acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server field in this case.
When DHCP is used, the following items need to be set.
Start IP:
This field specifies the first of the contiguous addresses in the IP address pool.
IP Pool Count:
This field specifies the count of the IP address pool.
Lease Time:
The current lease time of client.
Physical Ports:
Select to determine if the DHCPv4 server is applicable to the specific port or ports.
By default, all ports can obtain local IP from DHCPv4 server.
DNS Relay:
Select
Automatic
detection or
Manually
specific Primary and Secondary DNS IP addresses
BEC 6300VNL User Manual
Device Configuration
Interface Setup – LAN
62
Primary / Secondary DNS Server:
Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP clients along with the IP address and the subnet mask.
Fixed Host
In this field, users can map the specific IP (must in the DHCP IP pool) for some specific MAC, and this information can be listed in the following table.
IP Address:
Enter the specific IP. For example: 192.168.1.110.
MAC Address:
Enter the responding MAC. For example: 00:0A:F7:45:6D:ED
When added, you can see the ones listed as showed below:
IPv6 parameters
The IPv6 address composes of two parts, thus, the prefix and the interface ID.
Interface Address / Prefix Length:
Enter a static LAN IPv6 address. If you are not sure what to do with this field, please leave it empty as if contains false information it could result in LAN devices not being able to access other IPv6 device. Router will take the same WAN’s prefix to LAN side if the field is empty.
MLD Snooping:
Similar to IGMP Snooping, but applicable for IPv6.
DHCPv6 Server
There are two methods to dynamically configure IPv6 address on hosts,
Stateless
and
Stateful
.
Stateless auto-configuration
requires no manual configuration of hosts, minimal (if any) configuration of routers, and no additional servers. The stateless mechanism allows a host to generate its own addresses using a combination of locally available information (MAC address) and information (prefix) advertised by routers. Routers advertise prefixes that identify the subnet(s) associated with a link, while hosts generate an "interface identifier" that uniquely identifies an
BEC 6300VNL User Manual
Device Configuration
Interface Setup – LAN
63
interface on a subnet. An address is formed by combining the two. When using stateless configuration, you do not need to configure anything on the client.
Stateful configuration
, for example using DHCPv6 (which resembles its counterpart DHCP in IPv4.)
In the stateful auto configuration model, hosts obtain interface addresses and/or configuration information and parameters from a DHCPv6 server. The Server maintains a database that keeps track of which addresses have been assigned to which hosts.
DHCPv6 Server:
Check whether to enable DHCPv6 server.
DHCPv6 Server Type:
Select Stateless or Stateful. When DHCPv6 is enabled, this parameter is available.
Stateless:
If selected, the PCs in LAN are configured through RA mode, thus, the PCs in LAN are configured through RA mode, to obtain the prefix message and generate an address using a combination of locally available information (MAC address) and information (prefix) advertised by routers, but they can obtain such information like DNS from DHCPv6 Server.
Stateful:
If selected, the PCs in LAN will be configured like in IPv4 mode, thus obtain addresses and DNS information from DHCPv6 server.
Start interface ID:
enter the start interface ID. The IPv6 address composed of two parts, thus, the prefix and the interface ID. Interface is like the Host ID compared to IPv4.
End interface ID:
enter the end interface ID.
Leased Time (seconds):
the leased time, similar to leased time in DHCPv4, is a time limit assigned to clients, when expires, the assigned ID will be recycled and reassigned.
Router Advertisement:
Check to Enable or Disable the Issue Router Advertisement feature. This feature is to send Router Advertisement messages periodically which would multicast the IPv6 Prefix information (similar to v4 network number 192.168.1.0) to all LAN devices if the field is enabled. We suggest enabling this field.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless
64
Wireless
This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless
65
Access Point Settings
Access Point:
Default setting is set to
Activated
. If you want to close the wireless interface, select
Deactivated.
AP MAC Address:
The MAC address of wireless AP.
Wireless Mode:
The default setting is
802.11b+g+n
(Mixed mode). If you do not know or have both
11g and 11b devices in your network, then keep the default in
mixed mode
. From the drop-down manual, you can select
802.11g
if you have only 11g card. If you have only 11b card, then select
802.11b
and if you only have 802.11n then select
802.11n
.
Channel:
The range of radio frequencies used by IEEE 802.11b/g/n wireless devices is called a channel. There are Regulation Domains and Channel ID in this field. The Channel ID will be different based on Regulation Domains. Select a channel from the drop-down list box.
Beacon interval:
The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network.
RTS/CTS Threshold:
The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake.
Enter a value between 1500 and 2347.
Fragmentation Threshold:
The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter a value between 256 and 2346, even number only.
DTIM Interval:
This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication
Message (DTIM).
TX Power:
The transmission power of the antennas, ranging from 1-100, the higher the more powerful of the transmission performance.
IGMP Snooping:
Enable or disable the IGMP Snooping function for wireless. Without IGMP snooping, multicast traffic is treated in the same manner as broadcast traffic - that is, it is forwarded to all ports.
With IGMP snooping, multicast traffic of a group is only forwarded to ports that have members of that group.”
11n Settings
Channel Bandwidth:
Select
20 MHz, 40 MHz,
or
20/40 MHz
for the channel bandwidth. The wider the Channel bandwidth the better the performance will be.
Extension Channel:
This is for the 40MHz clients to use and is predefined to “
Above the control channel”
, not configurable.
Guard Interval:
Select either
400nsec
or
800nsec
for the guard interval. The guard interval is here to ensure that data transmission do not interfere with each other. It also prevents propagation delays, echoing and reflections. The shorter the Guard Interval, the better the performance will be. We recommend users to select Auto.
MCS (Modulation and Coding Scheme):
There are options
0~15
and
AUTO
to select from.
AUTO
is recommended.
SSID Settings
Available SSID:
User can determine how many virtual SSIDs to be used. Default is 1, maximum is 4.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless
66
SSID Index:
Select the number of SSIDs you want to use; up to 4 SSIDs are available in the list.
SSID:
The SSID is the unique name of a wireless access point (AP) to be distinguished from another.
For security propose, change the default
wlan-ap
to a unique ID name to the AP which is already builtin to the router’s wireless interface. Make sure your wireless clients have exactly the SSID as the device, in order to get connected to your network.
Broadcast SSID:
Select
Yes
to make the SSID visible so a station can obtain the SSID through passive scanning. Select
No
to hide the SSID in so a station cannot obtain the SSID through passive scanning.
Client Isolation:
(Known as AP Isolation) After enabling this feature, all Wi-Fi clients connect to the same Access Point, in the same local wireless network, cannot interact with each another.
SSID Activated:
Select the time period during which the SSID is active. Default is always which means
the SSID will be active all the time without time control. See Time Schedule to set the timeslot to
flexibly control when the SSID functions.
WPS Settings
WPS (Wi-Fi Protected Setup) feature is a standard protocol created by Wi-Fi Alliance. This feature greatly simplifies the steps needed to create a Wi-Fi network for a residential or an office setting. WPS supports 2 types of configuration methods which are commonly known among consumers:
Method (Personal Information Number)
&
PBC Method (Push Button Configuration)
.
Use WPS:
Enable this feature by choosing “YES” radio button.
WPS State:
Display whether the WPS is
configured
or
unconfigured
.
WPS Mode:
Select the mode which to start WPS, choose between
PIN Code
and
PBC
(Push Button).
Selecting
Pin Code
mode will require you to know the enrollee PIN code.
To future understand the two modes of configuration; please refer to the example of the
Wi-Fi
Protected Setup.
Security Settings
Security Type:
You can disable or enable wireless security for protecting wireless network. The default type of wireless security is OPEN and to allow all wireless stations to communicate with the access points without any data encryption.
To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers secure data encryption, known as WEP and WPA.
There are five alternatives to select from: WEP 64-bit, WEP 128-bit, WPA-PSK, WPA2-PSK, and Mixed
WPA/WPA2-PSK. If you require high security for transmissions, please select WPA-PSK, WPA2-PSK or WPA/WPA2-PSK.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless
67
WEP
WEP Authentication Method:
WEP authentication method, there are two methods of authentication used, Open System authentication (OPENWEB) and Share Key authentication (SHAREDWEB). We suggest you select OPENWEB.
Key 1 to Key 4:
Enter the key to encrypt wireless data. To allow encrypted data transmission, the
WEP Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required for 64bitWEP and 128-bitWEP respectively.
If you chose
WEP 64-bit
, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-
F").
If you chose
WEP 128-bit
, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "A-
F").
You must configure all four keys, but only one key can be activated at any one time. The default key is key 1.
NOTE: When you enable WPS function, this WEP function will be invalid. And if you select one of WEP-64Bits/
WEP-128Bits, the following prompt box will appear to notice you.
WPA-PSK & WPA2-PSK
WPA Algorithms:
TKIP (Temporal Key Integrity Protocol) or AES (Advanced Encryption System) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers.
Pre-Shared key:
The key for network authentication. The input format should be 8-63 ASKII characters or 64 hexadecimal characters
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless
68
Key Renewal Interval:
The time interval for changing the security key automatically between wireless client and AP.
WDS Settings
WDS (Wireless distributed system) is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed, just define the peer’s MAC of the connected AP.
WDS Mode:
select Activated to enable WDS feature and Deactivated to disable this feature.
MAC Address:
Enter the AP MAC addresses (in XX:XX:XX:XX:XX:XX format) of the peer connected
AP.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PIN)
Example: WPS using PIN Method (Personal Information Number)
PIN Method – Configure 6300VNL as a Registrar
1. Jot down the client’s Pin (e.g. 04640776) from the WPS utility (e.g. Ralink Utility)
69
2. Enter the Enrollee (Client) PIN code and then press
Start WPS
.
3. Go back to the wireless client’s WPS utility (e.g. Ralink Utility).
Set the Config Mode as
Enrollee
, press the WPS button on the top bar, select the AP (e.g. Billion_AP) from the WPS AP List column. Then press the PIN button located on the middle left of the page to run the scan.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PIN)
70
4. The client’s SSID and security setting will now be configured to match the SSID and security setting of the registrar, the 6300VNL router.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PIN)
PIN Method – Configure 6300VNL as an Enrollee
1. Jot down the AP PIN Code (e.g. 03454435) from the BEC 6300VNL. Press
Start
WPS.
71
2. Launch the wireless client’s WPS utility (e.g. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number in the PIN Code (e.g. 03454435) column then choose the correct AP (e.g. Billion_AP) from the WPS AP List before pressing the PIN button to run the scan.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PIN)
3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar (client).
72
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PBC)
Example: WPS using PBC Method (Push Button Configuration)
1. Click the
PBC
radio button and click
Save
to apply the settings
73
2. Launch the wireless client’s WPS Utility (e.g. Ralink Utility). Set the Config Mode as
Enrollee
. Then press the
WPS button
and choose the correct AP (e.g.
Billion_AP
) from the WPS AP List section before pressing the
PBC
button to run the scan.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless (Example on WPS using PBC)
74
3. When the PBC button is pushed, a wireless communication will be established between your router and the PC. The client’s SSID and security setting will now be configured to match the SSID and security setting of the router.
BEC 6300VNL User Manual
Device Configuration
Interface Setup – Wireless MAC Filter
75
Wireless MAC Filter
The MAC filter screen allows you to configure the router to give exclusive access to up to 8 devices
(Allow Association) or exclude up to 8 devices from accessing the router (Deny Association). Every
Ethernet device has a unique MAC (Media Access Control) address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:AA:BB:00:00:02.
You need to know the MAC address of the devices you wish to filter.
SSID Index:
Select the targeted SSID you want the MAC filter rules to apply to.
Active:
Select
Activated
to enable MAC address filtering.
Action:
Define the filter action for the list of MAC addresses in the MAC address filter table.
Select
Deny
to block access to the AP, MAC addresses not listed will be allowed to access the router.
Select
Allow
to permit access to the router, MAC addresses not listed will be denied access to the router.
MAC Address:
Enter the MAC addresses (in XX:XX:XX:XX:XX:XX format) of the wireless station that are allowed or denied access to the specified in these address fields.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Firewall
76
Advanced Setup
Advanced Step provides advanced features including
Firewall
,
Routing
,
NAT
,
Static DNS
,
QoS
,
Internet Grouping,
and
Time Schedule
for advanced users.
Firewall
Your router includes a firewall for helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet.
Firewall:
To automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death,
SYN Flood, Port Scan and Land Attack.
Enabled:
It activates your firewall function.
Disabled:
It disables the firewall function.
SPI:
If you enabled SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side.
Enabled:
It activates your SPI function.
Disabled:
It disables the SPI function.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Status Route
77
Routing
This is static route feature. You are equipped with the capability to control the routing of all the traffic across your network. With each routing rule created, user can specifically assign the destination where the traffic will be routed to.
#:
Item number
Destination IP Address:
IP address of the destination network
Subnet Mask:
The subnet mask of destination network.
Gateway IP Address:
IP address of the gateway or existing interface that this route uses.
Metric:
It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
Interface:
Media/channel selected to append the route.
Edit:
Edit the route; this icon is not shown for system default route.
Drop:
Drop the route; this icon is not shown for system default route.
Add Route
Destination IP Address:
This is the destination subnet IP address.
Destination Subnet Mask:
The subnet mask of destination network.
Gateway IP Address/Interface:
This is the gateway IP address or existing interface to which packets are to be forwarded.
Metric:
It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – NAT
78
NAT
The NAT (Network Address Translation) feature transforms a private IP into a public IP, allowing multiple users to access the internet through a single IP account, sharing the single IP address. NAT break the originally envisioned model of IP end-to-end connectivity across the internet so NAT can cause problems where IPSec/ PPTP encryption is applied or some application layer protocols such as
SIP phones are located behind a NAT. And NAT makes it difficult for systems behind a NAT to accept incoming communications.
NAT Status:
Enabled. (Disabled if WAN connection is in
BRIDGE
mode)
VPN Passthrough:
VPN pass-through is a feature of routers which allows VPN client on a private network to establish outbound VPNs unhindered.
SIP ALG:
Enable the SIP ALG when SIP phone needs ALG to pass through the NAT. Disable the SIP
ALG when SIP phone includes NAT-Traversal algorithm.
Interface:
Select a WAN interface connection to allow external access to your internal network.
Service Index:
Associated to EWAN interface marking each EWAN service (0-7), to select which
EWAN service the DMZ and Virtual server are applied to.
Click
DMZ
or
Virtual Server
to move on to set the DMZ or Virtual Server parameters, which are represented in the following scenario.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – NAT (DMZ)
79
DMZ
NOTE: This feature disables automatically if WAN connection is in BRIDGE mode.
The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by the Firewall and NAT algorithms then passed to the DMZ host, when a packet received does not use a port number used by any other
Virtual Server entries.
DMZ for (via a WAN Interface):
Allows outside network to connect in and communicate with internal
LAN devices via this WAN interface
Note:
Here you can see the Multiple IPs Account/EWAN Service ID 0. It is the interface set in the previous NAT page.
DMZ:
Enabled:
Activate the DMZ function.
Disabled:
Deactivate the DMZ function.
DMZ Host IP Address:
Give a static IP address to the DMZ Host when
Enabled
radio button is checked. Be aware that this IP will be exposed to the WAN/Internet.
Select the
Save
button to apply your changes.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – NAT (Virtual Server)
80
Virtual Server
NOTE: This feature disables automatically if WAN connection is in BRIDGE mode.
Virtual Server is also known as Port Forwarding that allows 6300VNL to direct all incoming traffic to the servers on the LAN.
Configure a virtual rule in 6300VNL for remote users accessing services such as Web or FTP services via the public (WAN) IP address that can be automatically redirected to local servers in the LAN network. Depending on the requested service (TCP/UDP port number), the device redirects the external service request to the appropriate server within the LAN network.
Virtual Server for:
Indicate the related WAN interface which allows outside network to connect in and communicate.
Protocol:
Choose the application protocol.
Start / End Port Number:
Enter a port or port range you want to forward.
(Example: Start / End: 1000 or Start: 1000, End: 2000).
The starting port must be greater than zero (0). The end port must be greater than or equal to the start port.
Local IP Address:
Enter your server IP address in this field.
Start / End Port Number (Local):
Enter the start / end port number of the local application (service).
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – NAT (Virtual Server)
Examples of well-known and registered port numbers are shown below. For further information, please see IANA’s website at http://www.iana.org/assignments/port-numbers
Well-known and Registered Ports
81
Port Number Protocol
21 TCP
22
23
TCP & UDP
TCP
25
53
69
80
TCP
TCP & UDP
UDP
TCP
110
443
1503
1720
7070
TCP
TCP & UDP
TCP
TCP
UDP
Description
FTP Control
SSH Remote Login Protocol
Telnet
SMTP (Simple Mail Transfer Protocol)
DNS (Domain Name Server)
TFTP (Trivial File Transfer Protocol)
World Wide Web HTTP
POP3 (Post Office Protocol Version 3)
HTTPS
T.120
H.323
RealAudio
Using port forwarding does have security implications, as outside users will be able to connect to PCs on your network. For this reason you are advised to use specific Virtual Server entries just for the ports your application requires, instead of using DMZ. As doing so will result in all connections from the WAN attempt to access to your public IP of the DMZ PC specified
.
Attention
If you have disabled the NAT option in the WAN-ISP section, the Virtual Server function will hence be invalid.
If the DHCP server option is enabled, you have to be very careful in assigning the IP addresses of the virtual servers in order to avoid conflicts. The easiest way of configuring Virtual Servers is to manually assign static IP address to each virtual server PC, with an address that does not fall into the range of IP addresses that are to be issued by the DHCP server. You can configure the virtual server IP address manually, but it must still be in the same subnet as the router.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – NAT (Example)
Example: How to setup Port Forwarding for port 21 (FTP server)
If you have a FTP server in your LAN network and want others to access it through WAN.
82
Step 1:
Assign a static IP to your local computer that is hosting the FTP server.
Step 2:
Login to the Gateway and go to
Configuration / Advanced Setup / NAT / Virtual Server.
FTP server uses TCP protocol with port 21.
Enter “21” to Start and End Port Number. BEC 6300VNL will accept port 21 requests from WAN side.
Enter the static IP assigned to the local PC that is hosting the FTP server. Ex: 192.168.1.102
Enter “21” to Local Start and End Port number. BEC 6300VNL will forward port 21 request from WAN to the specific LAN PC (ex:192.168.1.102) in the network.
Step 3:
Click
Save
to save settings.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Static DNS
83
Static DNS
The Domain Name System (DNS) is a hierarchical naming system built on a distributed database for computers, services, or any resource connected to the Internet or a private network associates various information with domain names assigned to each of the participating entities. Most importantly, it translates domain names meaningful to humans into the numerical identifiers associated with networking equipment for the purpose of locating and addressing these devices worldwide.
An often-used analogy to explain the Domain Name System is that it serves as the phone book for the
Internet by translating human-friendly computer hostnames into IP addresses. For example, the domain name www.example.com can be translated into the addresses 192.0.32.10 (IPv4).
Static DNS is a concept relative to Dynamic DNS, in static DNS system, the IP mapped is static without change
.
IP Address:
The IP address you are going to give a specific domain name.
Domain Name:
The friendly domain name for the IP address.
Press
Save
button to apply your settings.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – QoS
84
QoS
QoS helps you control the upload traffic of each application from LAN (Ethernet and/or Wireless) to
WAN (Internet).
It facilitates you the features to control the quality of throughput for each application. This is useful when there on certain types of data you want giver higher priority to, such as voice data packets given higher priority than web data packets.
Click
SETTING
to add QoS rules (up to
16
QoS rules).
Rule Index:
Index marking for each rule up to maximum of 16.
Active:
Select whether to activate the rule.
Destination IPv4/IPv6:
Set the IPv4/IPv6 address that you want to filter on destination side.
Destination Subnet Mask / IPv6 Prefix:
Specify the Destination Subnet Mask for IPv4 or prefix for
IPv6.
Destination Port Range:
Set the port range value that you want to filter on destination side.
Source IPv4/IPv6 Address:
Set the IP address value that you want to filter on source side in IPv4 or IPv6.
Source Subnet Mask / IPv6 Prefix:
Specify the Source Subnet Mask for IPv4 or prefix for IPv6.
Source Port Range:
Set the port range value that you want to filter on source side.
Protocol ID:
Set the protocol ID type of packets that you want to filter (TCP, UDP, ICMP, and IGMP).
Priority:
Select to prioritize the traffic which the rule categorizes, High or Low.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Interface Grouping
85
Interface Grouping
Interface grouping is a function to group interfaces, known as VLAN. A Virtual LAN, commonly known as a VLAN, is a group of hosts with the common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of the physical location.
A VLAN has the same attributes as a physical LAN, but it allows for end stations to be grouped together even if they are not located on the same network switch.
Similarly, they may also have been split into two different groups, even if they are on the same switch.
Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the
Save
button.
Interface Grouping:
Select
Yes
to enable Interface Grouping feature.
Group Index:
The index number indicating the current group ranging from 0 to 15.
EWAN Service:
The available EWAN interface. Move to Interface Setup to add other EWAN interface.
3G/4G-LTE:
The available 3G/4G-LTE interfaces.
Ethernet LAN:
The available Ethernet interfaces.
Wireless LAN:
The available wireless interfaces.
Group Summary:
Click
Group Summary
to check current group information.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Interface Grouping (Example)
86
Example: Create two EWAN services, Service0 (PPPoE) and Service1 (Bridge).
You are going to group the ports and services into two working group, as shown below.
Group Index
0
1
Group Port
EWAN0,LAN1, LAN2, WLAN1
EWAN1, LAN3
Click
Group Summary
to show the configuration results.
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Time Schedule
87
Time Schedule
The Time Schedule supports up to
16
timeslots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of the Internet by users or applications.
This Time Schedule correlates closely with router’s time, since router does not have a real time clock on board; it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server from the Internet.
Time Index:
The rule index (0-15) for identifying each timeslot.
Name:
User-defined identification for each time period.
Day of Week / Start Time / End Time:
Mon. to Sun. Specify the time interval for each timeslot from
“Day of Week”. For example, user can add a timeslot named “TimeSlot1” which features a period from 9:00 of Monday to 18:00 of Tuesday.
Another TimeSlot2 spanning from 09:00 to 18:00 of Friday
BEC 6300VNL User Manual
Device Configuration
Advanced Setup – Mail Alert
88
Mail Alert
Mail alert is designed to keep system administrator or other relevant personnel alerted of any unexpected events that might have occurred to the network computers or server for monitoring efficiency. With this alert system, appropriate solutions may be tackled to fix problems that may have arisen so that the server can be properly maintained.
SMTP Server:
Enter the SMTP server that you would like to use for sending emails.
Username:
Enter the username of your email account to be used by the SMTP server.
Password:
Enter the password of your email account.
Sender’s Email:
Enter your email address.
SSL/TLS:
Check to whether to enable SSL encryption feature.
Port:
the port, default is 25.
Account Test:
Click the button to test the connectivity and feasibility to your sender’s e-mail.
Recipient’s Email (WAN IP Change Alert):
Enter a valid e-mail address to receive an alert message when WAN IP change has been detected.
Recipient’s Email (3G/4G-LTE Usage Allowance):
E Enter a valid e-mail address to receive an alert message when t he 3G over Usage Allowance occurs.
Click
Apply
button to save your settings
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec
89
VPN
A
Virtual Private Network
(
VPN
) is a private network that interconnects remote (and often geographically separate) networks through primarily public communication infrastructures such as the Internet. VPNs provide security through tunneling protocols and security procedures such as encryption. For example, a VPN could be used to securely connect the branch offices of an organization to a head office network through the public Internet.
BEC 6300VNL supports
IPSec, PPTP, L2TP, GRE
for enterprise users.
IPSec
Internet Protocol Security
(
IPSec
) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session. IPSec also includes protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic keys to be used during the session.
IPSec is an end-to-end security scheme operating in the Internet Layer of the Internet Protocol Suite.
It can be used in protecting data flows between a pair of security gateways (
network-to-network
), or between a security gateway and a host (
network-to-host
).
A total of 8 IPSec tunnels can be added.
Click
Add New Connection
to create an IPSec connection.
BEC 6300VNL User Manual
IPSec Connection Setting
Device Configuration
VPN – IPSec
90
Connection Name:
Assign a name for this connection. Example: connection to office.
Active: Yes
to activate the connection.
Interface:
Select the set used interface for the IPSec connection, when you select 3G/4G-LTE interface, the IPSec tunnel would via this interface to connect to the remote peer.
Remote Gateway IP:
The WAN IP address of the remote VPN gateway that is to be connected, establishing a VPN tunnel.
Local Access Range:
Set the IP address or subnet of the local network.
Single IP:
The IP address of the local host, for establishing an IPSec connection between a security gateway and a host (
network-to-host
).
Subnet:
The subnet of the local network, for establishing an IPSec tunnel between a pair of security gateways (
network-to-network
)
Remote Access Range:
Set the IP address or subnet of the remote network.
Single IP:
The IP address of the local host, for establishing an IPSec connection between a security gateway and a host (network-to-host). If the remote peer is a host, select Single
Address.
Subnet:
The subnet of the local network, for establishing an IPSec tunnel between a pair of security gateways (network-to-network), If the remote peer is a network, select Subnet.
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec
91
IPSec Phase 1(IKE)
IKE Mode:
IKE, Internet Key Exchange, is the mechanism to negotiate and exchange parameters and keys between IPSec peers to establish security associations(SA). Select Main or Aggressive mode.
Pre-Shared Key:
This is for the Internet Key Exchange (IKE) protocol, a string from 4 to 128 characters. Both sides should use the same key. IKE is used to establish a shared security policy and authenticated keys for services (such as IPSec) that require a key. Before any IPSec traffic can be passed, each router must be able to verify the identity of its peer. This can be done by manually entering the pre-shared key into both sides (router or hosts).
Local ID Type
and
Remote ID Type:
When the mode of IKE is aggressive, Local and Remote peers can be identified by other IDs.
IDContent:
Enter IDContent the name you want to identify when the Local and Remote Type are
Domain Name; Enter IDContent IP address you want to identify when the Local and Remote Type are IP addresses (IPv4 and IPv6 supported).
Encryption Algorithm:
Select the encryption algorithm from the drop-down menu. There are several options: DES and AES (128, 192 and 256). 3DES and AES are more powerful but increase latency.
DES:
Stands for Data Encryption Standard, it uses 56 bits as an encryption method.
3DES:
Stands for Triple Data Encryption Standard, it uses 168 (56*3) bits as an encryption method.
AES:
Stands for Advanced Encryption Standards, you can use 128, 192 or 256 bits as encryption method.
Authentication Algorithm:
Authentication establishes the integrity of the datagram and ensures it is not tampered with in transmission. There are 3 options: Message Digest 5 (MD5) and Secure
Hash Algorithm (SHA1, SHA256). SHA1 is more resistant to brute-force attacks than MD5.
However, it is slower.
MD5:
A oneway hashing algorithm that produces a 128−bit hash.
SHA1:
A oneway hashing algorithm that produces a 160−bit hash.
Diffle-Hellman Group:
It is a public-key cryptography protocol that allows two parties to establish a shared secret over an unsecured communication channel (i.e. over the Internet). MODP stands for
Modular Exponentiation Groups.
IPSec Phase 2(IPSec)
IPSec Proposal:
Select the IPSec security method. There are two methods of verifying the authentication information, AH(Authentication Header) and ESP(Encapsulating Security Payload).
Use ESP for greater security so that data will be encrypted and the data origin be authenticated but using AH data origin will only be authenticated but not encrypted.
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec
92
Authentication Algorithm:
Authentication establishes the integrity of the datagram and ensures it is not tampered with in transmission. There are 3 options: Message Digest 5 (MD5) and Secure
Hash Algorithm (SHA1, SHA256). SHA1 is more resistant to brute-force attacks than MD5.
However, it is slower.
MD5:
A oneway hashing algorithm that produces a 128−bit hash.
SHA1:
A one-way hashing algorithm that produce s a 160−bit hash.
Encryption Algorithm:
Select the encryption algorithm from the drop-down menu. There are several options: DES and AES (128, 192 and 256). 3DES and AES are more powerful but increase latency.
DES:
Stands for Data Encryption Standard, it uses 56 bits as an encryption method.
3DES:
Stands for Triple Data Encryption Standard, it uses 168 (56*3) bits as an encryption method.
AES:
Stands for Advanced Encryption Standards, you can use 128, 192 or 256 bits as encryption method.
Perfect Forward Secrecy:
It is a public-key cryptography protocol that allows two parties to establish a shared secret over an unsecured communication channel (i.e. over the Internet). MODP stands for Modular Exponentiation Groups.
IPSec SA Lifetime
SA Lifetime:
Specify the number of minutes that a Security Association (SA) will stay active before new encryption and authentication key will be exchanged. There are two kinds of SAs, IKE and
IPSec. IKE negotiates and establishes SA on behalf of IPSec, an IKE SA is used by IKE.
Phase 1 (IKE):
To issue an initial connection request for a new VPN tunnel. The range can be from 5 to 15,000 minutes, and the default is 480 minutes.
Phase 2 (IPSec):
To negotiate and establish secure authentication. The range can be from 5 to 15,000 minutes, and the default is 60 minutes. A short SA time increases security by forcing the two parties to update the keys. However, every time the VPN tunnel re-negotiates, access through the tunnel will be temporarily disconnected.
IPSec Connection Keep Alive
Keep Alive:
None:
Disable. The system will not detect remote IPSec peer is still alive or lost. The remote peer will get disconnected after the interval, in seconds, is up.
PING:
This mode will detect the remote IPSec peer has lost or not by pinging specify IP address.
DPD:
Dead peer detection (DPD) is a keeping alive mechanism that enables the router to be detected lively when the connection between the router and a remote IPSec peer has lost.
Please be noted, it must be enabled on the both sites.
PING to the IP:
It is able to IP Ping the remote PC with the specified IP address and alert when the connection fails. Once alter message is received, Router will drop this tunnel connection.
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec
Reestablish of this connection is required. Default setting is 0.0.0.0 which disables the function
93
Interval:
This sets the time interval between Pings to the IP function to monitor the connection status. Default interval setting is 10 seconds. Time interval can be set from 0 to 3600 second, 0 second disables the function.
Ping to the IP Interval (sec)
0.0.0.0
0.0.0.0
0
2000 xxx.xxx.xxx.xxx (A valid IP Address) 0 xxx.xxx.xxx.xxx(A valid IP Address) 2000
Ping to the IP Action
No
No
No
Yes, activate it in every 2000 second.
Disconnection Time after No Traffic:
It is the NO Response time clock. When no traffic stage time is beyond the Disconnection time set, Router will automatically halt the tunnel connection and reestablish it base on the Reconnection Time set. 180 seconds is minimum time interval for this function.
Reconnection Time:
It is the reconnecting time interval after NO TRAFFIC is initiated. 3 minutes is minimum time interval for this function.
Click
Save
to apply the settings.
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec (Example on LAN-to-LAN)
Examples: IPSec
– Network (LAN) to Network (LAN)
Two of the
6300VNL devices want to setup a secure IPSec VPN tunnel
NOTE
: The IPSec Settings shall be consistent between the two routers.
94
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec (Example on LAN-to-LAN)
95
Head Office Side:
Configuration Settings
Connection Name
Remote Secure Gateway
Access Network
Local Access Range
Local Network IP Address
Local Network Netmask
H-to-B
69.121.1.30
Subnet
192.168.1.0
255.255.255.0
Remote Access Range Subnet
Remote Network IP Address 192.168.0.0
Remote Network Netmask
IPSec Proposal
255.255.255.0
IKE Mode
Pre-Shared Key
Phase 1 Encryption
Main
1234567890
AES-128
Phase 1 Authentication SHA1
Phase 1 Diffie-Hellman Group MODP 1024(group2)
Phase 2 Proposal
Phase 2 Authentication
ESP
SHA1
Phase 2 Encryption
Prefer Forward Security
3DES
MODP 1024(group2)
Description
Name for IPSec tunnel
IP address of the Branch office gateway
Head Office network
Branch office network
Security Plan
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec (Example on LAN-to-LAN)
96
Branch Office Side:
Configuration Settings
Connection Name
Remote Secure Gateway
Access Network
Local Access Range
Local Network IP Address
Local Network Netmask
B-to-H
69.121.1.3
Subnet
192.168.0.0
255.255.255.0
Remote Access Range Subnet
Remote Network IP Address 192.168.1.0
Remote Network Netmask
IPSec Proposal
255.255.255.0
IKE Mode
Pre-Shared Key
Phase 1 Encryption
Main
1234567890
AES-128
Phase 1 Authentication SHA1
Phase 1 Diffie-Hellman Group MODP 1024(group2)
Phase 2 Proposal
Phase 2 Authentication
ESP
SHA1
Phase 2 Encryption
Prefer Forward Security
3DES
MODP 1024(group2)
Description
Name for IPSec tunnel
IP address of the Branch office gateway
Head Office network
Branch office network
Security Plan
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec (Example on Remote Access)
Examples: IPSec
– Remote Employee to 6300VNL Connection
Router servers as VPN server, and host should install the IPSec client to connect to head office through IPSec VPN.
97
BEC 6300VNL User Manual
Device Configuration
VPN – IPSec (Example on Remote Access)
98
Head Office Side:
Configuration Settings
Connection Name
Remote Secure Gateway
Access Network
Local Access Range
Local Network IP Address
Local Network Netmask
H-to-H
69.121.1.30
Subnet
192.168.1.0
255.255.255.0
Remote Access Range Signal IP
Remote Network IP Address 69.121.1.30
Remote Network Netmask
IPSec Proposal
255.255.255.255
IKE Mode
Pre-Shared Key
Phase 1 Encryption
Main
1234567890
AES-128
Phase 1 Authentication SHA1
Phase 1 Diffie-Hellman Group MODP 1024(group2)
Phase 2 Proposal
Phase 2 Authentication
ESP
SHA1
Phase 2 Encryption
Prefer Forward Security
3DES
MODP 1024(group2)
Description
Name for IPSec tunnel
IP address of the Branch office gateway
Head Office network
Host
Security Plan
BEC 6300VNL User Manual
Device Configuration
VPN – PPTP Server
99
PPTP Server
The
Point-to-Point Tunneling Protocol
(PPTP) is a Layer2 tunneling protocol for implementing virtual private networks through IP network.
In the Microsoft implementation, the tunneled PPP traffic can be authenticated with PAP, CHAP, and
Microsoft CHAP V1/V2 . The PPP payload is encrypted using Microsoft Point-to-Point Encryption
(MPPE) when using MSCHAPv1/v2.
NOTE:
4 sessions for Client and 4 sessions for Server respectively.
PPTP Server:
Select
Activate
to enable PPTP Server.
Deactivate
to disable the PPTP Server.
Authentication Type:
The authentication type, Pap or Chap, and MPPE 128bit Encryption. When using PAP, the password is sent unencrypted, whilst CHAP encrypts the password before sending, and also allows for challenges at different periods to ensure that an intruder has not replaced the client. When passed the authentication with MS-CHAPv2, the MPPE encryption is supported.
MS-DNS:
Assign a DNS server or use router default IP address to be the MS-DNS server IP address.
Rule Index:
The numeric rule indicator for PPTP server. The maximum entry is up to 4.
Connection Name:
User-defined name for the PPTP connection.
Active
:
Yes
to activate the account. PPTP server is waiting for the client to connect to this account.
Username
: Please input the username for this account.
Password
: Please input the password for this account.
Connection Type
: Select Remote Access for single user, Select LAN to LAN for remote gateway.
Private IP Address Assigned to Dial-in User:
Specify the private IP address to be assigned to dial-in clients, and the IP should be in the same subnet as local LAN, but not occupied.
Remote Network IP Address
: Please input the subnet IP for remote network.
Remote Network Netmask
: Please input the Netmask for remote network.
Click
Save
to apply your settings.
BEC 6300VNL User Manual
Device Configuration
VPN – PPTP Client
100
PPTP Client
PPTP client can help you dial the PPTP server to establish PPTP tunnel over Internet. A total of 4 sessions can be created for PPTP client.
Rule Index:
The numeric rule indicator for PPTP client. The maximum entry is up to 4.
Connection Name:
User-defined name for the PPTP connection.
Active
:
Yes
to activate the account. PPTP server is waiting for the client to connect to this account.
Authentication Type:
The authentication type, Pap or Chap, and MPPE 128bit Encryption. When using PAP, the password is sent unencrypted, whilst CHAP encrypts the password before sending, and also allows for challenges at different periods to ensure that an intruder has not replaced the client. When passed the authentication with MS-CHAPv2, the MPPE encryption is supported.
Username
: Please input the username for this account.
Password
: Please input the password for this account.
Connection Type
: Select Remote Access for single user, Select LAN to LAN for remote gateway.
Server Address:
Enter the WAN IP address of the PPTP server.
Remote Network IP Address
: Please input the subnet IP for remote network.
Remote Network Netmask
: Please input the Netmask for remote network.
Click
Save
to apply the settings.
BEC 6300VNL User Manual
Device Configuration
VPN – PPTP (Example on Remote Dial-in)
Example: PPTP
– Remote Employee Dial-in to 6300VNL
101
The input IP address 192.168.1.2 will be assigned to the remote worker. Please make sure this IP is not used in the Office LAN.
Configuration Settings
Connection Name
Authentication Type
Username
Password
Connection Type
Assigned IP
HS-RA
MPPE 128bit test test
Remote Access
192.168.1.2
Description
Give a name of L2TP connection
Authentication type
Dial in authenticate user name
Dial in authenticate user password
Remote access for dial in
An IP assigned to the dial in client
BEC 6300VNL User Manual
Device Configuration
VPN – PPTP (Example on LAN-to-LAN)
Example: PPTP
– Network (LAN) to Network (LAN) Connection
102
The branch office establishes a PPTP VPN tunnel with head office to connect two private networks over the Internet. The routers are installed in the head office and branch offices accordingly.
NOTE:
Both office LAN networks must be in different subnets with the LAN-LAN application.
Configuring PPTP Server in the Head office
The IP address 192.168.1.2 will be assigned to the router located in the branch office. Please make sure this IP is not used in the head office LAN.
Configuration Settings
Connection Name
Authentication Type
Username
Password
Connection Type
Assigned IP
Remote Network IP
Remote Network Netmask
HS-LL
MPPE 128bit test test
LAN to LAN
192.168.1.2
129.168.0.0
255.255.255.0
Description
Give a name of PPTP connection
Authentication type
Dial in authenticate user name
Dial in authenticate user password
LAN to LAN for dial in
An IP assigned to the dial in client
Remote access network
Configuring PPTP Client in the Branch office
BEC 6300VNL User Manual
Device Configuration
VPN – PPTP (Example on LAN-to-LAN)
The IP address 69.1.121.33 is the Public IP address of the router located in head office.
Configuration Settings
Connection Name
Authentication Type
Username
Password
Connection Type
Server IP
Remote Network IP
Remote Network Netmask
BC-LL
MPPE 128bit test test
LAN to LAN
69.121.1.33
129.168.1.0
255.255.255.0
Description
Give a name of PPTP connection
Authentication type
Dial in authenticate user name
Dial in authenticate user password
LAN to LAN for dial in
Dialed server IP
Remote access network
103
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP
104
L2TP
L2TP, Layer 2 Tunneling Protocol
is a tunneling protocol used to support virtual private networks
(VPNs). It does not provide any encryption or confidentiality by itself; it relies on an encryption protocol that it passes within the tunnel to provide.
NOTE:
4 sessions for dial-in connections and 4 sessions for dial-out connections
Rule Index:
The numeric rule indicator for L2TP. The maximum entry is up to 8.
Connection Name:
User-defined name for the connection.
Active:
To enable or disable the tunnel.
Connection Mode (Dial in)
Connection Mode:
Select Dial In to operate as a L2TP server.
Authentication Type:
Default is Chap/Pap(CHAP, Challenge Handshake Authentication Protocol.
PAP, Password Authentication Protocol.) if you want the router to determine the authentication type to use, or else manually specify PAP if you know which type the server is using (when acting as a client), or else the authentication type you want clients connecting to you to use (when acting as a server).
Username:
Please input the username for this account.
Password:
Please input the password for this account.
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP
105
Private IP Address Assigned to Dial-in User:
The private IP to be assigned to dial-in user by L2TP server. The IP should be in the same subnet as local LAN, and should not be occupied.
Connection Mode (Dial out)
Connection Mode:
Choose Dial Out if you want your router to operate as a client (connecting to a remote L2TP Server, e.g., your office server).
Server IP Address:
Enter the IP address of your VPN Server.
Authentication Type:
Default is Chap/Pap(CHAP, Challenge Handshake Authentication Protocol.
PAP, Password Authentication Protocol.) if you want the router to determine the authentication type to use, or else manually specify PAP if you know which type the server is using (when acting as a client), or else the authentication type you want clients connecting to you to use (when acting as a server).
Username:
Please input the username for this account.
Password:
Please input the password for this account.
Connection Type
Remote Access:
From a single user.
LAN to LAN:
Enter the peer network information, such as network address and Netmask.
Tunnel Authentication and Active
Tunnel Authentication:
This enables router to authenticate both the L2TP remote and L2TP host.
This is only valid when L2TP remote supports this feature.
Secret Password:
The secure password length should be 16 characters which may include numbers and characters.
Local Host Name:
Enter hostname of Local VPN device that is connected / establishes a VPN tunnel.
Remote Host Name:
Enter hostname of remote VPN device. It is a tunnel identifier from the Remote
VPN device matches with the Remote hostname provided. If remote hostname matches, tunnel will be connected; otherwise, it will be dropped.
Active as Default Route:
Enabled to let the tunnel to be the default route for traffic, under this circumstance, all packets will be forwarded to this tunnel and routed to the next hop.
BEC 6300VNL User Manual
Click
Save
to apply the settings.
Device Configuration
VPN – L2TP
106
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP (Example on Remote Dial-in)
Example: L2TP VPN
– Remote Employee Dial-in to 6300VNL
107
A remote worker establishes a L2TP VPN connection with the head office using Microsoft's VPN
Adapter (included with Windows XP/2000/ME, etc.). The router is installed in the head office, connected to a couple of PCs and Servers.
The input IP address 192.168.1.200 will be assigned to the remote worker. Please make sure this IP is not used in the Office LAN.
Configuration Settings
Connection Name
Connection Mode
Authentication Type
Username
Password
Assigned IP
Connection Type
HS-RA
Dial in
Chap/Pap test test
192.168.1.200
Remote Access
Description
Give a name of L2TP connection
Operate as L2TP server
Authentication type
Dial in authenticate user name
Dial in authenticate user password
An IP assigned to the dial in client
Remote access for dial in
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP (Example on Remote Dial-out)
Example: L2TP VPN
– 6300VNL Dial-out to a Server
A company
’s office establishes a L2TP VPN connection with a file server located at a separate location. The router is installed in the office, connected to a couple of PCs and Servers.
108
Item
Connection Name
Connection Mode
Server IP
Authentication Type
Username
Password
Connection Type
HC-RA
Dial out
69.121.1.33
Chap/Pap test test
Remote Access
Description
Give a name of L2TP connection
Operate as L2TP client
Dialed server IP address
Authentication type
Dial out authenticate user name
Dial out authenticate user password
Remote access for dial out
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP (Example on LAN-to-LAN)
Example: L2TP VPN
– Network (LAN) to Network (LAN) Connection
109
The branch office establishes a L2TP VPN tunnel with head office to connect two private networks over the Internet. The routers are installed in the head office and branch office accordingly.
NOTE:
Both office LAN networks must be in different subnets with the LAN-LAN application.
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP (Example on LAN-to-LAN)
Configuring L2TP VPN Dial-in in the Head office
110
The IP address 192.168.1.200 will be assigned to the router located in the branch office. Please make sure this IP is not used in the head office LAN.
Item
Connection Name
Connection Mode
Authentication Type
Username
Password
Assigned IP
Connection Type
Remote Network IP
Remote Network Netmask
HS-LL
Dial in
Chap/Pap
Test
Test
192.168.1.200
LAN to LAN
129.168.0.0
255.255.255.0
Description
Give a name of L2TP connection
Operate as L2TP server
Authentication type
Dial in authenticate user name
Dial in authenticate user password
An IP assigned to the dial in client
LAN to LAN for dial in
Remote access network
BEC 6300VNL User Manual
Device Configuration
VPN – L2TP (Example on LAN-to-LAN)
Configuring L2TP VPN Dial-out in the Branch office
The IP address 69.1.121.33 is the Public IP address of the router located in head office.
Item
Connection Name
Connection Mode
Server IP
Authentication Type
Username
Password
Connection Type
Remote Network IP
Remote Network Netmask
BC-LL
Dial out
69.121.1.33
Chap/Pap test test
LAN to LAN
129.168.1.0
255.255.255.0
Description
Give a name of L2TP connection
Operate as L2TP client
Dialed server IP
Authentication type
Dial in authenticate user name
Dial in authenticate user password
LAN to LAN for dial out
Remote access network
111
BEC 6300VNL User Manual
Device Configuration
VoIP
–
Basic
112
GRE Tunnel
Generic Routing Encapsulation
(GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocol packets inside virtual point-to-point links over an IP network.
NOTE:
Up to 8 tunnels can be added.
Rule Index:
The numeric rule indicator for GRE. The maximum entry is up to 8.
Connection Name:
User-defined name for the connection.
Active:
Select Yes to activate the GRE tunnel.
Interface:
Select the exact WAN interface configured for the tunnel as the local IP.
Remote Gateway:
The remote GRE gateway IP.
Tunnel Local IP:
Please set the source IP for the local tunnel.
Tunnel Local Netmask:
Please set the Netmask for the local tunnel.
Tunnel Remote IP Address:
Set the peer IP address of the tunnel.
Remote Network IP Address
: Please set the subnet IP for remote network.
Remote Network Netmask
: Please set the Netmask for remote network.
Enable Keep-alive:
Normally, the tunnel interface is always up. Enable keep-alive to determine when the tunnel interface is to be closed. The local router sends keep-alive packets to the peer router, if keepalive response is not received from peer router within the allowed time (‘retry time’ mu ltiply ‘interval’, based on default settings, the time interval can be 30 seconds), the local router will shut up its tunnel interface.
Keep-alive Retry Times:
Set the keep-alive retry times, default is 3.
Keep-alive Interval:
Set the keep-alive Interval, unit in seconds. Default is 5 seconds.
MTU:
Maximum Transmission Unit.
BEC 6300VNL User Manual
Device Configuration
VoIP
–
Basic
Active as Default Route:
Select if to set the GRE tunnel as the default route.
Click
Save
to apply the settings.
113
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Device Management
114
Access Management
Device Management
Device management offers users a way to change the embedded web server accessing port, default
80. User can change the http port to 8080 or something else here.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
SNMP
115
SNMP
Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. BEC 6300VNL serves as a SNMP agent which allows a manager station to manage and monitor the router through the network.
SNMP:
Select to enable SNMP feature.
Get Community:
Type the Get Community, which is the password for the incoming Get-and-GetNext requests from the management station.
Set Community:
Type the Set Community, which is the password for incoming Set requests from the management station.
Trap Manager IP:
Enter the IP of the server receiving the trap message (when some exception occurs) sent by this SNMP agent.
SNMPv3:
Enable to activate the SNMPv3.
User Name:
Enter the name allowed to access the SNMP agent.
Access Permissions:
Set the access permissions for the user; RO--read only and RW--read and writer.
Authentication Protocol:
Select the authentication protocol, MD5 and SHA. SNMP agent can communicate with the manager station through authentication and encryption to secure the message exchange. Set the authentication and encryption information here and below.
Authentication Key:
Set the authentication key, 8-31 characters.
Privacy Protocol:
Select the privacy mode, DES and AES.
Privacy Key:
Set the privacy key, 8-31 characters.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Remote Syslog & UPnP
116
Remote Syslog
Remote Syslog allows users to set up an isolated external syslog server to receive system logs from the router for convenient view.
Remote Log:
Select whether to activate to use remote syslog service.
Server IP Address:
Enter your syslog server IP address.
Server UDP Port:
The syslog service UDP port, default is 514.
Universal Plug & Play
UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device.
Both the user’s Operating System and the relevant application must support UPnP in addition to the router. Windows XP and Windows ME natively support UPnP (when the component is installed), and
Windows 98 users may install the Internet Connection Sharing client from Windows XP in order to support UPnP. Windows 2000 does not support UPnP.
UPnP:
Select this checkbox to activate UPnP. Be aware that anyone could use a UPnP application to open the web configuration’s login screen without entering the BEC 6300VNL' IP address
Auto-configured:
Select this check box to allow UPnP-enabled applications to automatically configure the BEC 6300VNL so that they can communicate through the BEC 6300VNL, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to communicate with another UPnP enabled device; this eliminates the need to manually configure port forwarding for the UPnP enabled application.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
DDNS
117
Dynamic DNS
The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your internet connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your
ISP.
Here users can register different WAN interfaces with different DNS(es). But note that first users have to go to the Dynamic DNS registration service provider to register an account.
Dynamic DNS:
Select this check box to activate Dynamic DNS.
Service Provider:
Select from drop-down menu for the appropriate service provider, for example: www.dyndns.org.
My Host Name:
Type the domain name assigned to your BEC 6300VNL by your Dynamic DNS provider.
Username:
Type your user name.
Password:
Type the password.
Wildcard support:
Select this check box to enable DYNDNS Wildcard.
Period:
Set the time period between updates, for the Router to exchange information with the DDNS server. In addition to updating periodically as per your settings, the router will perform an update when your dynamic IP address changes.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
DDNS (Example)
Example: How to register a DDNS account
118
Note
first users have to go to the Dynamic DNS registration service provider to register an account.
User
test1
register a Dynamic Domain Names in DDNS provider
http://www.dyndns.org/
.
DDNS: www.hometest.com
using username/password test/test
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Access Control
119
Access Control
Access Control Listing allows you to determine which services/protocols can access BEC 6300VNL interface from which computers. It is a management tool aimed to allow IPs (set in secure IP address) to access specified embedded applications (Web, etc., user can set) through some specified interface
(LAN, WAN or both). User can have an elaborate understanding in the examples below.
The maximum number of entries is
16
.
Access Control:
Select whether to make Access Control function available.
Rule Index:
The numerical indication of the rules
Active:
Select to activate the rule.
Secure IP Address:
The default 0.0.0.0 allows any client to use this service to manage the BEC
6300VNL. Type an IP address range to restrict access to the client(s) without a matching IP address.
Application:
Choose a service that you want to all access to all the secure IP clients. The drop-down menu lists all the common used applications.
Interface:
Select the access interface. Choices are
LAN
,
WAN
and
Both
.
By default, the “Access Control” has
two default rules
.
Default Rule 1:
(Index 1), a rule to allow only clients from LAN to have access to all embedded applications (Web, FTP, etc.). Under this situation, clients from WAN cannot access the router even from Ping.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Access Control
Default Rule 2:
(Index 2), an ACL rule to open Ping to WAN side.
120
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Packet Filter (IP & MAC Filters)
121
Packet Filter
You can filter the packages by MAC address, IP address, Protocol, Port number and Application or
URL.
Packet Filter - IP & MAC Filter
Packet Filter
Filter Type:
There are three types “
IP & MAC Filter
”, “
Application Filter
”, and “
URL Filter
” that user can select for this filter rule. Here we set
IP & MAC Filter
.
IP & MAC Filter Editing
Rule Index:
The numerical indication of the rules.
Individual Active:
Select
Yes
to activate the rule.
Action:
This is how to deal with the packets matching the rule. Allow please select White List or block selecting Black List.
Interface:
Select which interface the rule will be applied to.
Direction:
Select if the rule applies to outgoing packets, incoming packets or both directions.
Type:
Choose type of field you want to specify to monitor. Select “IPv4” for IPv4 address, port number and protocol. Select “IPv6” for IPv6 address, port number and protocol. Select “MAC” for
MAC address.
Source IP Address:
The source IP address of packets to be monitored. 0.0.0.0 means “Don’t care”.
Source Subnet Mask:
Enter the subnet mask of the source network.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Packet Filter (IP & MAC Filters)
122
Source Port Number:
The source port number of packets to be monitored. 0 means “Don’t care”.
Destination IP Address:
The destination IP address of packets to be monitored. 0.0.0.0 means “Don’t care”.
Destination Subnet Mask:
Enter the subnet mask of the destination network.
Destination Port Number:
This is the Port that defines the application. (E.g. HTTP is port 80.)
DSCP:
DSCP: Differentiated Services Code Point, it is recommended that this option be configured by an advanced user or keep 0. (0 means Don’t care.)
Protocol:
Specify the packet type (TCP, UDP, ICMP, and ICMPv6) that the rule applies to.
IP/MAC Filter Listing
#:
Item number
.
Active:
Whether the connection is currently active.
Interface:
show the interface the rule applied to.
Direction:
show the direction the rule applied to.
Source IP (IPv6) Address/Mask (Prefix):
The source IP address or range of packets to be monitored.
Destination IP (IPv6) Address/Mask (Prefix):
This is the destination subnet IP address.
Source MAC Address:
show the MAC address of the rule applied.
Source Port:
The source port number of packets to be monitored.
Destination Port:
This is the Port or Port Ranges that defines the application.
DSCP:
show the set DSCP.
Protocol:
It is the packet protocol type used by the application. Select either
TCP
or
UDP
or
ICMP or
ICMPv6
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Packet Filter (Application & URL Filters)
Packet Filter - Application Filter
123
Application Filter:
Select this option to Activated/Deactivated the Application filter.
ICQ:
Select this option to Allow/Deny ICQ.
MSN:
Select this option to Allow/Deny MSN.
YMSG:
Select this option to Allow/Deny Yahoo messenger.
Real Audio/Video (RTSP):
Select this option to Allow/Deny Real Audio/Video (RTSP).
Packet Filter - URL Filter
URL Filter:
Select
Activated
to enable URL Filter.
URL Filter Rule Index:
The numerical indication of the rules.
Individual Active:
To give control to the specific URL access individually, for example, you want to prohibit access to www.yahoo.com
, please first press Activated in “URL Filter” field, and also Yes in
“Individual Active” field; if some time you want to allow access to this URL, you simply select No in individual active field. In a word, the command serves as a switch to the access of some specific URL with the filter on.
URL (Host):
Specified URL which is prohibited from accessing.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Parental Control
124
Parental Control
With this feature, router can reject to provide
Internet
services to the specified computer during some specified time interval. This can be very useful for parents to give control to children using computer without restraint.
Parent Control:
Select Activated to enable this feature.
MAC Address:
Type the MAC address(es) you want to block to access the internet (access to the router is sustained). The format of MAC address could be: xx:xx:xx:xx:xx:xx . If you want to set restriction to the Browser PC, you can directly check the checkbox of Browser’s MAC Address.
Block Schedule:
Select a timeslot throughout which the above set MAC is restricted to access internet.
See Time Schedule to set the exact timeslot.
Timeslot1 at Time Schedule:
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Samba & FTP Server
125
SAMBA & FTP Server
Samba and FTP are served as network sharing.
SAMBA Server:
Activated to enable SAMBA sharing.
Work Group:
The same mechanism like in Microsoft work group, please set the Work Group name.
NetBIOS Name:
The sharing NetBIOS name.
FTP Server:
Activated to enable FTP sharing.
FTP Server Port:
Set the working port. Well-known one is 21. User can change it.
SAMBA/FTP login account:
Default user:
admin/admin, it is the administrative user and a super user; it has the full authority of SAMBA /FTP access and operation permission of objects in SAMBA and FTP server.
New user:
users can create new user(s) to grant it (them) access and permission to the SAMBA
& FTP server.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Setup Samba (Example)
Example: How to setup Samba
126
1. Go directly to Start > Run (enter \\192,168,1,254 (from LAN side), \\SambaSvr , but if you enter
\\SambaSvr , please be sure your working PC is in the same workgroup as set in the samba server set above.)
2. Enter the Username and password.
3. Users can browse and access USB storage.
BEC 6300VNL User Manual
Device Configuration
Access Management
–
Setup FTP Server (Example)
Example: How to setup FTP
:
1.
Access via FTP tools
Take popular FTP tool of FlashFXP for example:
1) Open FlashFXP
2) Create ftp sites (LAN IP / WAN IP, 192.168.1.254, and set the account, port).
3) Connect to the ftp site.
127
2.
Web FTP access
1) Enter ftp://192.168.1.254
at the address bar of the web page.
2) Enter the account's username and password.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
User Management (Administrator Account)
128
Maintenance
Maintenance gives users the ability to maintain the device as well as examine the connectivity of the
WAN connections, including
User Management
,
Time Zone
,
Firmware & Configuration
,
System
Restart
, and
Diagnostic Tool.
User Management
User Management controls the Router Web GUI permission, FTP/SAMBA access to the specific account.
In factory setting, the default accounts are
admin/admin
and
user/user.
The default root account admin has been authorized to web access of router, Samba access, and FTP access.
user/user
is equipment with limited access (specified by advanced users with admin account) to router web, and
FTP/SAMBA . A total of
6
other accounts can be created to grant access to the access of Samba and
FTP and web page (need to be specified).
Note:
SAMBA account set here.
Administrator Account admin/admin
is the root account provided by our router.
Note: This username / password may vary by different Internet Service Providers.
User Setup
Index:
The numeric account indicator. The maximum entry is up to 8 accounts.
User Name:
Create account(s) user name for GUI management.
New Password:
Enter a new password for this user account.
Confirmed Password:
Re-enter the new password again; you must enter the password exactly the same as in the previous field
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
User Management (Administrator Account)
FTP Authority Setup
FTP Access:
Enable to grant the user access to the FTP server.
Permission:
Set the operation permission for the user, Read/Write or Read.
129
SAMBA Authority
SAMBA Access:
Enable to grant the user access to the SAMBA server.
Permission:
Set the operation permission for the user, Read/Write or Read.
Web GUI Permission
Login using the Administrator account, you will have the full accessibility to manage & control your
BEC 6300VNL device and can also create user accounts for others to control some of the open configuration settings.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
User Management (User Account)
User Account (Adding additional user accounts) user/user
is the default user account username and password
NOTE: This username / password may vary by different Internet Service Providers.
130
User Setup
Index #:
The numeric account indicator. The maximum entry is up to 8.
User Name:
Create account(s) user name for GUI management.
New Password:
Enter a new password for this user account.
Confirmed Password:
Re-enter the new password again; you must enter the password exactly the same as in the previous field
FTP Authority Setup
FTP Access:
Enable to grant the user access to the FTP server.
Permission:
Set the operation permission for the user, Read/Write or Read.
SAMBA Authority
SAMBA Access:
Enable to grant the user access to the SAMBA server.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
User Management (User Account)
Permission:
Set the operation permission for the user, Read/Write or Read.
131
Web GUI Permission
Guest Account:
Enable to create this new guest account.
Interface Setup / Advanced Setup / Access Management Setup / Maintenances:
Enable to grant this user access to these features.
When someone accesses to the 6300VNL using this “user” account, he/she can only manage and configure the features that is pre-selected in
Web GUI Permission
for this account..
Click
Save
to apply the settings.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
Time Zone
132
Time Zone
With default, 6300VNL does not contain the correct local time and date.
There are several options to setup, maintain, and configure current local time/date on the 6300VNL.
If you plan to use
Time Schedule
feature, it is extremely important you set up the Time Zone correctly.
Synchronize time with:
Select the methods to synchronize the time.
NTP Server automatically:
To synchronize time with the SNTP servers to get the current time from an SNTP server outside your network then choose your local time zone. After a successful connection to the Internet, 6300VNL will retrieve the correct local time from the SNTP server this is specified.
PC’s Clock:
To synchronize time with the PC’s clock.
Manually:
Select this to enter the SNMP server IP address manually.
Time Zone:
Choose the time zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT).
Daylight Saving:
Select this option if you use daylight savings time.
NTP Server Address:
Enter the IP address of your time server. Check with your ISP/network administrator if you are unsure of this information.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
Firmware Configuration
133
Firmware & Configuration
Firmware is the software that controls the hardware and provides all functionalities which are available in the GUI. This software may be improved and/or modified; your BEC 6300VNL provides an easy way to update the code to take advantage of the changes. .
To upgrade the firmware of BEC 6300VNL, you should download or copy the firmware to your local environment first. Press the
“Browse…”
button to specify the path of the firmware file. Then, click
“Upgrade”
to start upgrading. When the procedure is completed, BEC 6300VNL will reset automatically to make the new firmware work.
Upgrade:
Choose Firmware or Configuration you want to update.
System Restart with:
Current Settings:
Restart the device with the current settings automatically when finishing upgrading.
Factory Default Settings:
Restart the device with factory default settings automatically when finishing upgrading.
File:
Type in the location of the file you want to upload in this field or click
Browse
to find it.
Browse:
Click
Browse...
to find the configuration file or firmware file you want to upload. Remember that you must extract / decompress / unzip the .zip files before you can upload them.
Backup Configuration:
Click
Backup
button to back up the current running configuration file and save it to your computer in the event that you need this configuration file to be restored back to your
BEC 6300VNL device when making false configurations and want to restore to the original settings.
Upgrade
: Click
“Upgrade”
to begin the upload process. This process may take up to two minutes.
DO NOT turn off / power off the device or interrupt the firmware upgrading while it is still in process. Improper operation could damage your BEC 6300VNL.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
System Restart
134
System Restart
Click
System Restart
with option
Current Settings
to reboot your router.
If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select
Factory Default Settings
to restore to factory default settings.
You may also restore your router to factory settings by holding the small Reset pinhole button on the back of your router in about more than 6s seconds whilst the router is turned on.
BEC 6300VNL User Manual
Device Configuration
Maintenance
–
Auto Reboot
135
Auto Reboot
Schedule an automatic reboot for your 6300VNL to ensure proper operation and best performance.
This reboot will only reboot with current configuration settings and not overwrite any existing settings.
Click
Save
to apply the settings
Example:
Schedule 6300VNL to reboot at 10:00pm (22:00) every weekday (Monday thru Friday) and reboot at 9:00am on Saturday and Sunday.
BEC 6300VNL User Manual
Device Configuration
Maintenance – Diagnostic Tool
136
Diagnostics Tool
The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides.
3G/4G-LTE
Click START to begin to diagnose the connection.
BEC 6300VNL User Manual
EWAN
Click START to begin to diagnose the connection.
Device Configuration
Maintenance – Diagnostic Tool
137
BEC 6300VNL User Manual
C
HAPTER
5: T
ROUBLESHOOTING
Troubleshooting
138
If your
BEC 6300VNL
is not functioning properly, you can refer to this chapter for simple troubleshooting before contacting your service provider support. This can save you time and effort but if symptoms persist, consult your service provider.
Problems with the Router
Problem
None of the LEDs is on when you turn on the router
You have forgotten your login username or password
Suggested Action
Check the connection between the router and the adapter. If the problem persists, most likely it is due to the malfunction of your hardware. Please contact your service provider or BEC for technical support.
Try the default username "admin" and password
"admin". If this fails, you can restore your router to its factory settings by pressing the reset button on the device rear side.
Problem with LAN Interface
Problem
Cannot PING any PC on LAN
Suggested Action
Check the Ethernet LEDs on the front panel.
The LED should be on for the port that has a PC connected. If it does not lit, check to see if the cable between your router and the PC is properly connected. Make sure you have first uninstalled your firewall program before troubleshooting.
Verify that the IP address and the subnet mask are consistent for both the router and the workstations.
BEC 6300VNL User Manual
Troubleshooting
139
Recovery Procedures
Problem
- The front LEDs display incorrectly
- Still cannot access to the router management interface after pressing the RESET button.
- Software / Firmware upgrade failure
Suggested Action
1. Power on the router, once the Power LED lit red, please press this reset button using the end of paper clip or other small pointed object immediately.
2. The router’s emergency-reflash web interface will then be accessible via http://192.168.1.1 where you can upload a firmware image to restore the router to a functional state, Please note that the router will only respond with its web interface at this address
(192.168.1.1), and will not respond to ping request from your PC or other telnet operations.
BEC 6300VNL User Manual
Appendix
140
A
PPENDIX
: P
RODUCT
S
UPPORT
& C
ONTACT
If you come across any problems please contact the dealer from where you have purchased the product.
Contact BEC @ http://www.bectechnologies.net
MAC OS is a registered Trademark of Apple Computer, Inc.
Windows 10/8/7, Windows XP, and Windows Vista are registered Trademarks of Microsoft Corporation.
BEC 6300VNL User Manual
Appendix
141
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. . This device and its antenna(s) must not be colocated or operating in conjunction with any other antenna or transmitter.
Co-location statement
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
BEC 6300VNL User Manual
Appendix
142
IC Regulations
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
BEC 6300VNL User Manual
Appendix
143
Detachable Antenna Usage
This device has been designed to operate with an antenna having a maximum gain of 2.5dB.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
The required antenna impedance is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter (IC: 5315A- 6300VNOZ / Model: BEC 6300VNL ; BEC 6300 ;
RidgeWave 6300VNL ; BEC 6300NEL ; RidgeWave 6300NEL) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB 2.5.
Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada.
L'impédance d'antenne requise est de 50 ohms.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.
Le présent émetteur radio (IC: 5315A-6300VNOZ / Model: BEC 6300VNL ; BEC 6300 ;
RidgeWave 6300VNL ; BEC 6300NEL ; RidgeWave 6300NEL) a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Approved antennas list
Type
Dipole
Dipole
Gain
1.5dBi
2.5dBi
Brand
BEC
BEC
Manufacture
INVAX System Technology Corp.
INVAX System Technology Corp.
BEC 6300VNL User Manual
Appendix
144
V102brc9dg4
BEC 6300VNL User Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 37 CHAPTER 4: DEVICE CONFIGURATION
- 40 Device Info
- 42 System Status
- 42 System Log
- 43 3G/4G-LTE Status
- 44 Statistics
- 48 DHCP Table
- 48 Disk Status
- 49 IPSec Status
- 50 PPTP Status
- 51 L2TP Status
- 51 GRE Status
- 52 VoIP Status
- 56 Interface Setup
- 57 Internet
- 68 Wireless
- 79 Wireless MAC Filter
- 80 Advanced Setup
- 80 Firewall
- 81 Routing
- 87 Static DNS
- 89 Interface Grouping
- 91 Time Schedule
- 92 Mail Alert
- 93 IPSec
- 103 PPTP Server
- 104 PPTP Client
- 116 GRE Tunnel
- 118 Access Management
- 118 Device Management
- 120 Remote Syslog
- 120 Universal Plug & Play
- 121 Dynamic DNS
- 123 Access Control
- 125 Packet Filter
- 128 Parental Control
- 129 SAMBA & FTP Server
- 132 Maintenance
- 132 User Management
- 136 Time Zone
- 137 Firmware & Configuration
- 138 System Restart
- 139 Auto Reboot
- 140 Diagnostics Tool
- 142 CHAPTER 5: TROUBLESHOOTING
- 142 Problems with the Router
- 142 Problem with LAN Interface
- 143 Recovery Procedures
- 146 IC Warning
- 147 Detachable Antenna Usage