Nitto ASH-800 Instruction manual
विज्ञापन
विज्ञापन
AIR FILE
Please read this manual carefully before you attempt to use your tool so that you may use it properly and safely.
SUPER HAND
Model ASH-800
PROFESSIONAL TOOL
Specifications
Model
Rated Air Pressure
Air Consumption at Free Speed
Stroke Speed
Stroke Length
MAX.Shank Dia. of Points
Maximum Weight of Applications
ASH-800
0.6MPa(6kgf/cm
2
)
0.23m
3
/min
6500min
-1
8mm
φ 5.5mm
0.02kg
Sound Pressure Level
Sound Power Level
(ISO 15744)
Vibration Level (ISO 8662-12)
Mass (Weight)
Thread Size of Air Inlet
73dB(A)
84dB(A)
8.1m/s
2
0.52kg
Rc1/4(PT1/4)
Due to continuous product development/improvement the specifications and configurations in this document are subject to change without prior notice.
Manufactured by :
NITTO KOHKI Co., Ltd.
2-9-4, Nakaikegami, Ohta-ku,
Tokyo, 146-8555, Japan
Keep the manual handy – so you can use it whenever necessary.
Thank you very much for your purchase of Nitto Kohki products. Before using your tool, please read this manual carefully so that you may use it properly to get the most out of it. Please keep the manual handy - so you can use it whenever necessary.
CONTENTS page
IMPORTANT SAFETY INSTRUCTIONS ……………………………………… 2
GENERAL: TOOLS ……………………………………………………………… 2
GENERAL: PNEUMATIC TOOLS ……………………………………………… 3
INSTRUCTIONS FOR THIS TOOL …………………………………………… 4
1. APPLICATION ………………………………………………………………… 4
2. RECEIVING INSPECTION …………………………………………………… 4
3. AIR SUPPLY …………………………………………………………………… 4
4. OPERATION …………………………………………………………………… 5
5. THREAD SIZE OF HOSE FITTING ………………………………………… 5
6. OPTIONAL PARTS …………………………………………………………… 5
7. ORDERING PARTS …………………………………………………………… 5
8. EXPLODED DIAGRAM : ASH-800 PARTS LIST ………………………… 6
1
The following Safety notations are used throughout the manual to highlight safety precautions for the user and for the machine.
Warning:
Indicates a potentially hazardous situation which, if not avoided by following the instructions given, could result in death or serious injury.
Caution:
Indicates a potentially hazardous situation which, if not avoided by following the instructions given, could result in injury or material damage.
Please note, however, that failure to observe safety precautions under the “ Caution” category could result in a serious occurrence depending on the situation: please observe all safety precautions in the manual.
Caution: Important precautions for machine or tool setup, operation and maintenance.
IMPORTANT SAFETY
INSTRUCTIONS
When using the tool, please take the basic safety precautions as described below to prevent possible injury.
GENERAL: TOOLS
Warning
To Operators
●
Wear proper clothing for the type of work being done.
No loose clothing nor adornments when at work: you will be pulled into the tool if you’re unlucky. Wear nonskid footwear. If you have long hair, wear a safety hat that can cover up your hair completely.
●
Always wear safety glasses.
Remember, regular glasses are no safety glasses.
The lenses are only shock resistant, which will not give you sufficient eye protection you may need in your working environment.
●
Wear respiratory protective equipment (PPE).
Wear respiratory protective equipment (PPE) when working in an environment where dust particles are generated in operation.
●
Avoid working posture that is too stressful.
Secure good footing, work in a well-balanced posture.
●
Do not operate the machine if you are too tired.
●
Never touch any moving member on the tip of machine when running.
About Work Area
●
Keep the work area clean.
Cluttered work areas (e.g. workbench) invite accidents.
●
Carefully select the work area.
Do not expose tool to rain. Do not use tool in a wet or soaked area.
See that the work area is adequately illuminated.
●
Never work near inflammable liquid or in a potentially explosive atmosphere.
●
Keep children off the work area.
Keep children and unauthorized persons off the work area.
Before Operation
●
Inspect tool before use.
Before using, check that screws are securely tightened, that a protective cover and other parts are free from damage, and that the tool runs as it should.
Check that moving members are properly adjusted for positioning and tightened, that parts are free from damage and properly mounted, and that all other parts are in good condition for normal operation.
Should you find any damage to the protective cover or other part, replace it in accordance with the
Operation Manual. If there are no instructions in the
Manual, please contact sales agent through which you have purchased your tool or an authorized dealer near you for repair.
Likewise, if a switch failure occurs, contact sales agent through which you have purchased your tool or an authorized dealer near you for repair.
Do not use the tool -- if it does not start or stop with the start/stop switch.
●
Securely mount File
Improperly mounted File may fly out, causing possible damage to the machine or injury to the operator, etc.
●
Always remove spanner, wrench, etc., once adjustment is made with them.
●
Use a tool appropriate for the application.
Avoid heavy-duty application that is beyond the capacity of tool.
Do not use tool for other purposes than is geared to.
●
Do not abuse tool.
Use tool in accordance with the specifications: you’ll get the most out of it while ensuring safely.
●
Securely fasten workpiece in place.
Use a vice or clamp to securely fasten the workpiece in place. It is much safer this way than holding it in your hand, allowing you to operate the tool with both hands.
About Handling
●
How to store tool.
When the tool is not used, store it in a dry area and out of reach of children.
●
How to carry tool.
Do not touch the start switch while the tool is being carried.
●
Do not leave the tool unattended while it is running.
Turn off the start switch and disconnect the tool from power source. Do not leave the work area until the tool comes to a complete stop.
2
3
Maintenance/service
●
Do not take apart or modify tool.
Disassembling or modification carried out without the supervision by a qualified or authorized service engineer might cause accident.
●
Inspect cutting tool and accessories, etc.
A l w a y s c h e c k t o s e e t h a t L a p p i n g t o o l a n d accessories, etc. are in good operating condition without damage or deterioration -- before you mount them on the power tool. Should you find any damage to an accessory or part, please contact sales agent through which you have purchased your tool or an authorized dealer near you for repair.
●
Check parts for damage.
When you have found damage to accessory or other part, carefully check the damaged part to determine the extent of influence it has upon the functions of the power tool – that is, determine whether it can still perform its normal functions. Check to see that the linkage of the moving members is OK, that all parts are OK without damage, that they are properly mounted, and that the power tool functions normally.
Should you find any damage to an accessory or part that may hamper proper functioning of the tool, please contact sales agent through which you have purchased your tool or an authorized dealer near you for repair.
●
Have your tool repaired at Nitto service station
For repair or parts replacement please contact sales agent through which you have purchased your tool or an authorized dealer near you.
●
Use Nitto genuine parts.
Use of improper parts may result in serious occurrence.
To obtain a Nitto genuine part, consult this Manual or contact sales agent from which you have purchased your tool directly.
●
Do not detach label or nameplate from tool.
When a label or nameplate gets scratched or peeled off, contact sales agent through which you have purchased your tool or Nitto Koki Co., Ltd. directly for a replacement.
GENERAL: PNEUMATIC
Warning
TOOLS
●
Use appropriate air pressure.
Excessively high air pressure will increase the number of revolutions or strokes, causing not only premature failure or breakage but also unexpected accident.
●
Connect only pneumatic air supply lines.
Never attempt to connect the Air Lapping Tool to any supply line other than a pneumatic air supply line. There are other kinds of supply lines and pipes, such as oxygen supply lines, nitrogen supply lines or gas pipes.
Never attempt to connect the Air Lapping Tool to any of these other types of supply lines.
Attempting to connect the Air Lapping Tool to any supply line other than a pneumatic air supply line can result in accidents and/or severe injury.
●
Start tool properly.
Turn the start switch OFF before connecting the tool to the hose leading to air supply line.
●
Always disconnect the tool from the connecting hose leading to air supply line before putting on or taking off accessories or before getting down to maintenance work.
●
Avoid exposure to exhaust air.
Exhaust air contains from pneumatic tool contains oil and contaminated moisture. Make sure that exhaust air will not be directed to your face or anyone else who may be around.
●
Keep tool off electricity.
The pneumatic tool is not insulated against electricity. You may get electric shock if your pneumatic tool comes into contact with running electricity: keep it off electricity.
Caution
●
Handle tool carefully.
Abusive use of tool would invite failure or accident.
Do not throw or drop; don’t give tool a shock.
●
Handle connecting hose carefully.
Don’t hold the tool by the connecting hose when carrying it; don’t pull the connecting hose to disconnect.
INSTRUCTIONS FOR
THIS TOOL
Warning
●
Wear protective glasses and a dustproof mask
Operation generates chips and dust particles, etc. which may cause eye and/or respiratory injury: Always use PPE (Personal Protective
Equipment) for eye and respiratory protection.
●
If discomfort or pain is encountered during use, you should cease operations and check with your physician.
●
Be sure to keep hands clear of moving parts.
●
Always turn off the air supply and disconnect the air supply hose before replacing or adjusting a file and a part on the tool.
Caution
●
Use NITTO genuine parts files and pads.
●
Use of the ones other than NITTO genuine parts may cause abnormal vibration or defective finishing surface.
●
The weight of the accessory for this tool should be 12~15g.
1. APPLICATION
This tool is for filing the workpieces using the exclusive file.
2. RECEIVING INSPECTION
Upon unpacking, check to see that the shipment is complete without damage or oil leakage in transport.
Should you find any damage or short-shipment, please contact sales agent through which you have purchased your machine or an authorized dealer near you for corrective actions.
Package Content
SUPER HAND ASH-800
Rat Tail File SF-10
Triangular Taper File SF-11
Half Round File (Rat Tail / Double
Cut) SF-12
Flat Bastard File SF-13
Hex. Wrench Key 2.5
Bushing PT1/4×NPT1/4
Instruction Manual
1
1
1
1
1
Q’ty
1set
1
1
3. AIR SUPPLY
3-1. Air Pressure
Adjust air pressure with the air regulator to the level appropriate for the pneumatic tool used.
Air pressure that is too low fails the tool to operate at full capacity.
Air pressure that is too high may cause damage to the tool.
3-2. Air Line (Fig. 1)
Use a 9.5 mm (3/8”) connecting hose between the compressor and the tool.
Drained water, etc., if flown into the tool, could cause tool failure. Install an air filter. between the compressor and the tool.
s s r e
C o m p o r
Air Regulator
Air Filter
TOOL
Oiler
9.5mm (3/8 in)
Hose
Fig. 1
3-3. Lubrication
Caution
●
Always lubricate with a few drops of oil (ISO
VG-10), 2 to 3 times a day.
Install an oiler between the compressor and the tool. Use Machine Oil #10. Failure to lubricate causes damage to the tool. Lubricating oil with high viscosity degrades tool performance.
4
4. OPERATION
4-1. Mounting / Removing the file (Fig. 2)
Warning
●
Always turn off the air supply and disconnect the air supply hose.
Mounting
Insert the file shaft into the Holder and tighten the Hex.
Socket Set Screw with the Hex. Wrench Key until the file is securely fixed.
Removing
Loosen the Hex Socket Set Screw with the Hex.
Wrench Key and take it out.
Hex. Wrench Key
Hex. Socket Set Screw
Holder
File
Fig. 2
4-2. Start and Stop (Fig. 3)
Warning
To start : Turn the Valve Ring clockwise a and match
“ ▲ ” to “ ■ ” on the Housing.
To stop : Turn the Valve Ring counterclockwise and match “ ▲ ” to “ ● ” on the Housing.
Housing
Valvering
5
Fig. 3
4-3. Operation
Warning
●
Always wear eye protection during operations.
●
Start the operation and press the tool slightly to
the workpiece. Even if the tool is strongly pressed, the filing efficiency cannnot be improved.
4-4. How to use the Sanding Pad (Optional
Accessories) (Fig. 4)
(1) Attach the Abrasive Paper on the sponge of
Sanding Pad and fix it with the Paper Clamp as shown on the figure 4.
(2) Mount the Sanding Pad in the same menner as the one for the file and carry out operation.
(3) Cut the locally available the Abrasive Paper into
20mm × 190mm size and use it.
Note: The Sanding Pad may cause the larger vibration of the tool than the one caused by the file.
Sponge
Abrasive paper Fix the Abrasive paper on the sponge
Paper Clamp
A
Hang the A point of
Paper Clamp to the Shaft
Hang it to the shaft
Fig. 4
4-5. Storing Tool
Warning
●
When tool is not used, store it out of reach of children.
When the tool is not used, store it in a dry area.
If the tool is left alone as it has been used without preparation for storage, ambient moisture will remain inside the tool, which will leave it susceptible to rusting. After finishing your work, add the machine oil
#10 through the Air Hose and run the tool for a while before storage.
5. THREAD SIZE OF HOSE FITTING
The product comes with a metal fitting with PT thread. Connect the Bushing PT thread X NPT thread containing standard accessories. If you would like to have American NPT thread.
6. OPTIONAL PARTS
In addition to standard accessory parts, the following parts are available for your application and needs.
Part No.
Part Name
TA9A222 Rat Tail File SF-10
TA9A223 Triangular Taper File SF-11
TA9A224 Half Round File (Rat Tail /
Double Cut) SF-12
TA9A225 Flat Bastard File SF-13
TB03887 Sanding pad Ass’y
Q’ty
5pcs.
5pcs.
5pcs.
5pcs.
1set.
7. ORDERING PARTS
When ordering parts from our agency, plesase be sure to give them part number, part name and quantities.
8. EXPLODED DIAGRAM : ASH-800 PARTS LIST
Warning
This diagram is for refrence only. Do not attempt to service or repair the Nitto Air Lapping Tool. Do not take the Tool apart. Contact an authorized Nitto dealer for all service and repair of the Tool.
Improper service and repair can cause accidents and severe injuries.
Never attempt to modify the Tool.
Never attempt to service or repair the Tool yourself.
37
36
39
6
The part numbers with ( ) are included in the Ass’y parts written above them.
No.
Part No.
1 TQ04988 Collar
Part Name
Hex. Socket Set Screw with
2 TQ00485
Flat Point 5×6
Internal Retaining Ring
3 CQ03877
IRTW-18
4 TQ04986 Guide
Hex. Socket Set Screw with
5 TP00639
Flat Point 4×3
6 TQ04984 Front Case
7
8
TQ04987 Holder
TB03853 Front End Cap Ass’y
9 (TP03978) Oil Seal G10×14×13
10 (TA9A101) U Seal Ass’y
11 (TQ01971) Bushing
12 (CP24319) O-Ring JASO-1018
13 TB03854 Front Piston Ass’y
14 TB03928 Piston Ring Ass’y
Q’ty Price
1
1
1
1
1
15 TP02152 Washer M5
Hex. Socket Head Cap
16 TP00126
Screw 5×16
17 TQ04994 Spring 0.8×13.5×40
18 TB03856 Rear Piston Ass’y
19 TQ05000 Partition
20 TQ05007 O-Ring S-63
21 TQ04999 Cylinder
22 TB03918 Housing Ass’y
1
23 (TQ05069) Label Warning
24 (TQ05010) Label Model Number
25 TB03857 Rear End Cap Ass’y
26 (CP24319) O-Ring JASO-1018
28 TP11994 O-Ring P-4
29 TB03878 Hose Nipple Ass’y
30 (TP07006) Spring Pin 2×8
31 TQ05002 Shim
32 TQ13162 Lock Plate
33 CP25822 O-Ring JASO-2018
34 TB03861 Valve Ring Ass’y
35
36
39
37
(TQ05012) Label Serial Number
TB08131 Air Hose K Ass’y
(TQ11519) Label Lubrication
CP25581 O-Ring JASO-1015
1
1
1
1set
1
1set
1
1
38 TQ1125 Exhaust Hose 1
40 TQ05009 External Retaining Ring STW-7 1
41 TQ05353 Spacer 7.1×12.2×6 1
1
1
1set
3
2
1set
1
1set
2
2
1
1set
1
1
1set
1set
1set
1
1
1set
2sets
1
Part list of accessories
No.
Part No.
TP00700
Part Name
Rat Tail File SF-10
TP00701 Triangular Taper File SF-11
Half Round File (Rat Tail
TP00702
/ Double Cut) SF-12
TP00703
TP04305
TQ05087
TP02236
Flat Bastard File SF-13
Hex. Wrench Key 2.5
Instruction Manual
Bushing PT1/4×NPT1/4
1
1
1
1
Q’ty Price
1
1
1
7
SUPER HAND Model ASH-800
PROFESSIONAL TOOL
Printed in JAPAN
TQ05087-5
डाउनलोड
विज्ञापन