ST 3000 Smart Transmitter Specification and Model

ST 3000 Smart Transmitter
34-ST-03-57
6/07
Series 900 Remote Diaphragm Seals Models
STR93D
0 to 100 psid
0 to 7 bar
STR94G
0 to 500 psig
0 to 35 bar
Specification and
Model Selection
Guide
Introduction
In 1983, Honeywell introduced the first
Smart Pressure Transmitter― the ST
3000®. In 1989, Honeywell launched
the first all digital, bi-directional protocol
for smart field devices. Today, its
ST 3000 Series 900 Remote Seal
Transmitters continue to bring proven
“smart” technology to a wide spectrum
of pressure measurement applications.
For applications in which the
transmitter must be mounted remotely
from the process, Honeywell offers the
remote seal line of gauge, absolute and
differential pressure transmitters.
Typical applications include level
measurement in pressurized vessels in
the chemical and hydrocarbon
processing industries. A second
application is flow measurement for
slurries and high viscosity fluids in the
chemical industry. Honeywell remote
seal transmitters are available with
secondary fill fluids for corrosive or high
temperature process fluids
All ST 3000 transmitters can provide a
4-20 mA output, Honeywell Digitally
Enhanced (DE) output, HART* output,
or FOUNDATION™ Fieldbus output.
When digitally integrated with
Honeywell’s Process Knowledge
System™, EXPERION PKS™,
ST 3000 instruments provide a more
accurate process variable as well as
advanced diagnostics.
Honeywell’s cost-effective ST 3000
S900 transmitters lead the industry in
reliability and stability:
•
•
Stability = ±0.01% per year
Reliability = 470 years MTBF
Figure 1—Series 900 Remote Seal Pressure Transmitters feature proven
piezoresistive sensors and advanced seal technology with standard weld
connections.
The devices provide comprehensive self-diagnostics to help users
maintain high uptime, meet regulatory requirements, and attain high
quality standards. S900 transmitters allow smart performance at
analog prices. Accurate, reliable and stable, Series 900 transmitters
offer greater turndown ratio than conventional transmitters.
"Honeywell transmitters operating in the digital mode using
Honeywell's Digitally Enhanced (DE) protocol make diagnostics
available right at the control system's human interface. Equally
important, transmitter status information is continuously displayed to
alert the operator immediately of a fault condition. Because the
process variable (PV) status transmission precedes the PV value, we
are guaranteed that a bad PV is not used in a control algorithm. In
addition, bi-directional communication provides for remote transmitter
configuration directly from the human interface, enabling management
of the complete loop.”
Maureen Atchison, DuPont
Site Electrical & Instrumentation Leader
34-ST-03-57
Page 2
Description of Diaphragm Seals
Diaphragm seals are traditionally used when a standard pressure transmitter should not be exposed to the
process pressure directly. Diaphragm seals typically protect the pressure transmitter from one or more
damaging aspects of the process media. Consideration for using a diaphragm seal should be made in the
following circumstances.
•
•
•
•
•
•
•
•
•
High Process Temperature
Process Media is Viscous or Contains Suspended Solids
Process Media is Subject to Solidifying
Process Media is Corrosive
Process Application Requires Sanitary Connections
Process Application Subjects the Measuring Instrument to Hydrogen Permeation
Tank Level Applications with Maintenance Intensive Wet Legs
Tank Application with Density or Interface Measurements
Measuring Instrument Requires Remote Mounting
The following diaphragm seals are standard from Honeywell (please call your local salesperson if you do not see
the product you need for your application):
Figure 2 - Flush Flange Seals can be used with
differential, gauge and absolute pressure transmitters
and are available with 3” ANSI Class 150, ANSI Class
300 and DIN DN80-PN40 process connections. Flush
flange seals can also be provided with Lowers.
Lowers are essentially calibration rings, which allow
flushing connections if needed – see Figure 31.
Figure 2
Figure 3 - Flange Seal with Extended Diaphragm
can be used with differential, gauge and absolute
pressure transmitters and are available with 3” and 4”
ANSI Class 150, ANSI Class 300, DIN DN80-PN40
and DIN DN100-PN40 process connections. 2”, 4” and
6” extension lengths are available.
Figure 3
Figure 4 - Pancake Seals can be used with
differential, gauge and absolute pressure transmitters
and are available with 3” ANSI Class 150, 300 and 600
process connections.
Figure 4
Figure 5 - Chemical Tee “Taylor” Wedge seals can
be used with differential pressure transmitters and are
available with Taylor Wedge 5” O.D. process
connection.
Figure 5
34-ST-03-57
Page 3
Description of Diaphragm Seals
Figure 6 - Seals with Threaded Process
Connections can be used with differential, gauge and
absolute pressure transmitters and are available with
½”, ¾” and 1” NPT Female process connections.
Figure 6
Figure 7 - Sanitary Seals can be used with
differential, gauge and absolute pressure transmitters
and are available with 3” and 4” Tri-Clover-Tri-Clamp
process connections.
Figure 7
Figure 8 - Saddle Seals can be used with differential,
gauge and absolute pressure transmitters and are
available with 3” and 4” (6 bolt or 8 bolt designs)
process connections.
Figure 8
Figure 9 - Calibration Rings are available with Flush
Flange Seals and Pancake Seals. Flushing ports (1/4”
or ½”) are available with calibration rings.
Figure 9
Figure 10 - Stainless Steel Armor and PVC Coated
Stainless Steel Armor Capillaries are available with
Honeywell Remote Seal Solutions.
Figure 10
Figure 11 - 2” Stainless Steel Nipples are available
for Close-Coupled remote seal solutions.
Figure 11
34-ST-03-57
Page 4
Figure 12 - Welded Meter Body for All-Welded
Remote Seal Solution. The welded ST 3000 meter
body is an important part of an All-Welded Remote
Seal Solution, which is commonly used in Vacuum
applications.
Figure 12
Description
Features
The ST 3000 transmitter can replace any 4 to 20 mA output transmitter in
use today and operates over a standard two-wire system.
•
Choice of linear or square
root output conformity is a
simple configuration selection.
The measuring means is a piezoresistive sensor, which actually contains
three sensors in one. It contains a differential pressure sensor, a
temperature sensor, and a static pressure sensor.
•
Direct digital integration with
Experion PKS and other
control systems provides local
measurement accuracy to the
system level without adding
typical A/D and D/A converter
inaccuracies.
•
Unique piezoresistive sensor
automatically compensates
input for temperature and
static pressure.Added “smart”
features include configuring
lower and upper range
values, simulating accurate
analog output, and selecting
preprogrammed engineering
units for display.
•
Smart transmitter capabilities
with local or remote
interfacing means significant
manpower efficiency
improvements in
commissioning, start-up, and
ongoing maintenance
functions.
Microprocessor-based electronics provide higher span-turndown ratio,
improved temperature and pressure compensation, and improved
accuracy.
The transmitter’s meter body and electronics housing resist shock,
vibration, corrosion, and moisture. The electronics housing contains a
compartment for the single-board electronics, which is isolated from an
integral junction box. The single-board electronics is replaceable and
interchangeable with any other ST 3000 Series 100 or Series 900 model
transmitter.
Like other Honeywell transmitters, the ST 3000 features two-way
communication and configuration capability between the operator and the
transmitter through several Honeywell field-rated portable configuration
devices, including the Smart Field Communicator (SFC) and the Multiple
Communication Configurator (MC ToolKit). While both are made for infield use, the MC Toolkit also can be ordered for use in intrinsically safe
environments.
®
The SCT 3000 Smartline Configuration Toolkit provides an easy way to
configure instruments using a personal computer. The toolkit enables
configuration of devices before shipping or installation. The SCT 3000 can
operate in the offline mode to configure an unlimited number of devices.
The database can then be loaded down-line during commissioning.
34-ST-03-57
Page 5
Specifications
Operating Conditions – All Models
Reference
Condition
(at zero
static)
Rated Condition
°C
°F
°C
°F
°C
Ambient Temperature
25 ±1
77 ±2
-25 to 70
-13 to 158
-40 to 85
Process Interface
Temperature
Humidity
25 ±1
77 ±2
Parameter
%RH
Maximum Allowable
Working Pressure (MAWP)
Operative Limits
°F
0 to 100
°C
°F
-40 to 185 -55 to 125 -67 to 257
See Figure 13
10 to 55
Transportation
and Storage
-55 to 125 -67 to 257
0 to 100
0 to 100
MAWP is minimum of Body Rating or Seal Rating (See Model Selection Guide for Seal
MAWP)
Body
STR93D
STR94G
MAWP
750 psig (52 bar)
500 psig (35 bar)
Vacuum Region, Minimum
Pressure - mmHg absolute
inH2O absolute
atmospheric
atmospheric
Supply Voltage, Current,
and Load Resistance
Voltage Range: 10.8 to 42.4 Vdc at terminals
Current Range: 3.0 to 21.8 mA
Load Resistance: 0 to 1440 ohms (as shown in Figure 14)
See Figure 13
34-ST-03-57
Page 6
Figure 13—ST 3000 Remote Seals operable limits for pressure versus temperature
34-ST-03-57
Page 7
1440
1200
Loop
Resistance
(ohms)
Note: A minimum of 250 ohms
of loop resistance is necessary
to support communications.
Loop resistance equals barrier
resistance plus wire resistance
plus receiver resistance.
800
650
450
250
= Operating Area
0
10.8
16.28 20.63 25
28.3
37.0
42.4
Operating Voltage (Vdc)
Figure 14—Supply voltage and loop resistance chart
Performance Under Rated Conditions * - Model STR93D (0 to 100 psi/7 bar)
Parameter
Description
Upper Range Limit
psi
bar
100 (Transmitter URL or maximum seal pressure rating, whichever is lower.)
7
Minimum Span
psi
bar
0.9
0.063
Turndown Ratio
110 to 1
Zero Elevation and Suppression
No limit except minimum span within ±100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.20% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (50 inH2O), accuracy equals:
• Accuracy includes residual error
after averaging successive
readings.
50 inH2O
±0.10 + 0.10 ⎛ span inH O⎞ or ±0.10 + 0.10
2 ⎠
⎝
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
Combined Zero and Span
Temperature Effect per 28°C
(50°F) **
125 mbar
( span
mbar) in % of span
In Digital Mode: ±0.175% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
For URV below reference point (50 inH2O), accuracy equals:
50 inH2O
±0.075 + 0.10 ⎛ span inH O⎞ or ±0.075 + 0.10
2 ⎠
⎝
125 mbar
( span
mbar) in % of span
In Analog Mode: ±1.5% of span.
For URV below reference point (200 inH2O), effect equals:
±0.30 + 1.2
⎛
⎝
200 in H2O
span in H2O
⎞ or ±0.30 + 1.2 ⎛
⎝
⎠
500 mbar
span mbar
⎞ In % span
⎠
In Digital Mode: ±1.475% of span.
For URV below reference point (200 inH2O), effect equals:
±0.275 + 1.2
*
⎛
⎝
200 in H2O
span in H2O
⎞ or ±0.275 + 1.2 ⎛
⎝
⎠
500 mbar
span mbar
⎞ In % span
⎠
Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
** Specification applies to transmitters with 2 seals only. Apply 1.5 times factor to temperature effect for capillary lengths greater than 10 feet
or for 2-inch sanitary seals.
34-ST-03-57
Page 8
Performance Under Rated Conditions * - Models STR94G (0 to 500 psi/35 bar)
Parameter
Description
Upper Range Limit
psi
bar
500
35
Minimum Span
psi
bar
20
1.4
Turndown Ratio
25 to 1
Zero Elevation and Suppression
No limit except minimum span from absolute 0 (zero) to +100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
In Analog Mode: ±0.10% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
• Accuracy includes residual error
after averaging successive
readings.
In Digital Mode: ±0.075% of calibrated span or upper range value (URV), whichever
is greater, terminal based.
• For FOUNDATION Fieldbus use
Digital Mode specifications. For
HART use Analog Mode
specifications.
*
Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
Transmitter Minimum Span and Maximum Capillary Length
Minimum recommended span for STR93D DP Transmitter with two Remote Seals
Diaphragm
Size
2.0
2.4
2.9
3.5
4.1
5'
15 psig
150 iwc
50 iwc
25 iwc
25 iwc
10'
20 psig
200 iwc
75 iwc
25 iwc
25 iwc
15'
25 psig
250 iwc
100 iwc
25 iwc
25 iwc
Capillary
20'
300 iwc
125 iwc
28 iwc
25 iwc
25'
350 iwc
150 iwc
32 iwc
25 iwc
30'
400 iwc
175 iwc
36 iwc
27 iwc
35'
450 iwc
200 iwc
40 iwc
30 iwc
Capillary Length
maximum
15'
35'
35'
35'
35'
Minimum recommended span for STR94G or STR93D DP Transmitter with one Remote Seal
Diaphragm
Size
2.0
2.4
2.9
3.5
4.1
Direct
Mount
25 psi
10 psi
8 psi
2 psi
0.9 psi
5'
30 psi
15 psi
9 psi
2 psi
0.9 psi
10'
40 psi
20 psi
10 psi
3 psi
1 psi
Capillary
15'
20'
50 psi
25 psi
30 psi
11 psi
12 psi
4 psi
5 psi
2 psi
3 psi
30'
40 psi
14 psi
7 psi
4 psi
35'
50 psi
15 psi
8 psi
5 psi
Capillary Length
maximum
15'
35'
35'
35'
35'
Minimum span is the higher of the value from the table above or the value defined under Performance Conditions for the range transmitter
Figure 15— Maximum capillary length and diaphragm size chart.
Performance Under Rated Conditions - General for all Models
Parameter
Description
Output (two-wire)
Analog 4 to 20 mA or DE digital communications mode. Options available for
FOUNDATION Fieldbus and HART protocols.
Supply Voltage Effect
0.005% of span per volt.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
CE Conformity (Europe)
89/336/EEC, Electromagnetic Compatibility (EMC) Directive.
NAMUR NE 43 Compliance
Option
Transmitter failure information is generated when the measuring information is invalid or
no longer present. Failure information is transmitted as a current signal but outside the
normal 4-20 mA measurement signal level. Transmitter failure values are:
≤ 3.6 mA and ≥ 21.0 mA. The normal signal range is ≥ 3.8 mA and ≤ 20.5 mA.
SIL 2/3 Compliance
SIL certified to IEC 61508 for non-redundant use in SIL 2 related Safety Systems
(single use) and for redundant (multiple) use in SIL 3 Safety Systems through
TÜV Nord Sys Tec GmbH & Co. KG under the following standards: IEC61508-1: 1998;
IEC 61508-2: 2000; IEC61508-3: 1998.
34-ST-03-57
Page 9
Physical and Approval Bodies
Parameter
Description
Process Interface
See Model Selection Guide for Material Options for desired Seal Type.
Seal Barrier Diaphragm
316L Stainless Steel, Monel, Hastelloy C, Tantalum
Seal Gasket Materials
Klinger C-4401 (non-asbestos)
Grafoil
Teflon
Gylon 3510
Mounting Bracket
Carbon Steel (zinc-plated) or Stainless Steel angle bracket or Carbon Steel flat
bracket available.
Fill Fluid (Meter Body)
Silicone (DC 200)
S.G. @ 25°C (77°F) = 0.94
CTFE (Chlorotrifluoroethylene)
S.G. @ 25°C (77°F) = 1.89
Fill Fluid (Secondary)*
Silicone (DC 200)
S.G. @ 25°C (77°F) = 0.94
CTFE (Chlorotrifluoroethylene)
S.G. @ 25°C (77°F) = 1.89
Silicone (DC 704)
Syltherm 800
S.G. @ 25°C (77°F) = 1.07
S.G. @ 25°C (77°F) = 0.90
NEOBEE M-20
S.G. @ 25°C (77°F) = 0.93
Electronics Housing
Epoxy-Polyester hybrid paint. Low-copper aluminum alloy. Meets NEMA 4X
(watertight) and NEMA 7 (explosion proof)
Capillary Tubing**
Armored Stainless Steel or PVC Coated Armored Stainless Steel. Length: 5, 10,
15, 20, 25 and 35 feet (1.5, 3, 4.6, 6.1, 7.5 and 10.7m). A 2” (51 millimeter) S.S.
close-coupled nipple is also available. See Model Selection Guide.
Wiring
Accepts up to 16 AWG (1.5 mm diameter)
Mounting
See Figure 16.
Dimensions
See Figures 19 and 20 for transmitter dimensions. See Model Selection Guide for
Seal dimensions
Net Weight
Transmitter: 4.1 Kg (9 lbs). Total weight is dependent on seal type and capillary
length.
Approval Bodies
Factory Mutual
CSA
Canadian Registration
Number (CRN)
ATEX
SA (Australian)
INMETRO (Brazil)
Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups A,
B, C, D locations,
Dust Ignition Proof: Approved as Dust Ignition Proof for Class II, III, Division 1,
Groups E, F, G locations,
Intrincically Safe: Approved as Intrinsically Safe for for Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G locations.
Nonincendive: Approved as Nonincendive for Class I, Division 2, Groups A, B, C,
D locations.
Explosion Proof: Approved as Explosion Proof for Class I, Division 1, Groups B,
C, D locations,
Dust Ignition Proof: Approved as Dust Ignition Proof for Class II, III, Division 1,
Groups E, F, G locations,
Intrincically Safe: Approved as Intrinsically Safe for Class I, II, III, Division 1,
Groups A, B, C, D, E, F, G locations.
All ST 3000 model designs, except SATG19L, STG99L, STG170 and STG180
have been registered in all provinces and territories in Canada and are marked
CRN:0F8914.5c.
Intrinsically Safe, Zone 0/1:
Flameproof/Zone 1:
Non-Sparking, Zone 2:
Multiple Markings:
EEx ia IIC T4, T5, T6
EEx d IIC T5, T6 (enclosure IP 66/67)
EEx nA, IIC T6 (enclosure IP 66/67)
Ex II 1 G: EEx ia IIC T4, T5, T6, Ex II 2 G: EExd IIC T5, T6
Ex II 3 G: EEx nA, IIC T6 (Honeywell) (enclosure IP 66/67)
Intrinsically Safe: EX ia IIC T4
Non-Sparking: Ex n IIC T6 (T4 with SM option)
Flame-Proof, Zone 1:
EX d IIC T5
34-ST-03-57
Page 10
Parameter
Pressure Equipment Directive
(97/23/EC)
Description
The ST 3000 pressure transmitters listed in this Specification have no pressurized
internal volume or have a pressurized internal volume rated less than 1,000 bar
(14,500 psig) and/or have a maximum volume of less than 0.1 liter. Therefore,
these transmitters are either; not subject to the essential requirements of the
directive 97/23/EC (PED, Annex 1) and shall not have the CE mark, or the
manufacturer has the free choice of a module when the CE mark is required for
pressures > 200 bar (2,900 psig).
* See Figure 13 for Fill Fluid temperature limits.
** 2-inch Sanitary Seals are limited to 15 ft. (4.6 m) capillary length.
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from
exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive
97/23/EC article 1, 2.1.3), require separate examination.
LP Side
Maximum level
H2
Fixed
ref. leg
Variable
Head
H1
Minimum level
.
HP Side
NOTE: Lower flange seal should not be mounted over 22 feet below the
transmitter for silicone fill fluid (11 feet for CTFE fill fluid) with tank at one
atmosphere. The combination of tank vacuum and high pressure capillary
head effect should not exceed 9 psi vacuum (300 mmHg absolute).
Consult Honeywell for installation of STR93D
Figure 16—Typical mounting arrangement for ST 3000 Transmitter with Remote Diaphragm Seals
34-ST-03-57
Page 11
Application Data
Liquid Level: Closed Tank
Determine the minimum and
maximum pressure differentials to
be measured (Figure 17).
PMin = (SGp x a) - (SGf x d)
= LRV when HP at bottom of
tank
= –URV when LP at bottom of
tank
PMax = (SGp x b) - (SGf x d)
= URV when HP at bottom of
tank
= –LRV when LP at bottom of
tank
Max
LP
Level
b
Min
a
Level
¥ Transmitter above datum
Max
Where:
HP
LP
Level
minimum level = 4mA
maximum level = 20 mA
a = distance between bottom tap
and minimum level
b = distance between bottom tap
and maximum level
b
Min
a
Level
HP
¥ Transmitter at datum
d = distance between taps
SGf = Specific Gravity of capillary
fill fluid (See Page 9 for
values.)
Max
LP
Level
SGp = Specific Gravity of process
fluid
b
Min
Level
a
HP
¥ Transmitter below datum
24253
Figure 17—Closed tank liquid level measurement distances
34-ST-03-57
Page 12
Density or Interface
Calculate the minimum and
maximum pressure differentials to
be measured (Figure 18).
Pmin = (SGmin – SGf) x (d);
minimum density, 4mA output
LP
Pmax = (SGmax – SGf) x (d);
maximum density, 20mA output
Where:
d = distance between the taps
SGmax = maximum Specific
Gravity
SGmin = minimum Specific Gravity
SGf = Specific Gravity of capillary
fill fluid (See Page 9 for
values.)
HP
24257
Figure 18—Density, direct acting transmitter configuration
34-ST-03-57
Page 13
Reference Dimensions:millimeters
Inches
With
Smart
meter
82.9
3.26
45.7
1.8
53.1
2.09
Without
meter
94.9
3.74
65.1
2.56
Removal
Clearance
for All Caps
3.6
Plug
0.14
135
5.32
with meter
Without
meter
55.3
2.18
23.5
.925
Optional
external
ground
Optional
Meters
Rotational
Lock
LP seal
omitted for
clarity
67
2.64
93.6
3.69
STR93D DP/I Remote Seal with Horizontal Pipe Mount
With
Smart
meter
3.6
Plug
0.14
135
5.32
82.9
3.26
45.7
1.8
53.1
2.09
Without
meter
94.9
3.74
65.1
2.56
Removal
Clearance
for All Caps
with meter
Without
meter
55.3
2.18
23.5
.925
Rotational
Lock
Optional
Meters
Optional
external
ground
STR94G LGP/I Remote Seal with Horizontal Pipe Mount
Figure 19—Approximate horizontal mounting dimensions for Remote Seal Transmitter.
Seal
omitted for
clarity
24272
34-ST-03-57
Page 14
Reference Dimensions:millimeters
Inches
With
Smart
meter
82.9
3.26
45.7
1.8
94.9
3.74
53.1
2.09
Without
meter
Removal
Clearance
for All Caps
65.1
2.56
3.6
Plug
0.14
with meter
Without
meter
135
5.32
55.3
2.18
Seal
omitted for
clarity
23.5
.925
Rotational
Lock
LP seal
omitted for
clarity
Optional
Meters
Optional
external
ground
67
2.64
93.6
3.69
STR93D DP/I Remote Seal with Vertical Pipe Mount
3.6 Plug
0.14
With
Smart meter
135
5.32
55.3
2.18
Rotational
Lock
82.9
3.26
53.1
2.09
45.7
1.8
Without
meter
94.9
3.74
65.1
2.56
Removal
Clearance
for All Caps
with meter
Without
meter
23.5
.925
Optional
Meters
Optional
external
ground
Seal
omitted for
clarity
STR94G LGP/I Remote Seal with Vertical Pipe Mount
24273
Figure 20—Approximate vertical mounting dimensions for Remote Seal Transmitter
34-ST-03-57
Page 15
Options
Mounting Bracket
The angle-mounting bracket is
available in either zinc-plated
carbon steel or stainless steel and
is suitable for horizontal or vertical
mounting on a two-inch (50
millimeter) pipe, as well as wall
mounting. An optional flat
mounting bracket is also available
in carbon steel for two inch (50
millimeter) pipe mounting.
Indicating Meter
(Options ME and SM)
Two integral meter options are
available. An analog meter (option
ME) is available with a 0 to 100%
linear scale. The Smart Meter
(option SM) provides an LCD
display for both analog and digital
output and can be configured to
display pressure in pre-selected
engineering units.
Lightning Protection
(Option LP)
A terminal block with circuitry that
protects the transmitter from
transient surges induced by
nearby lightning strikes is
available.
®
HART Protocol Compatibility
(Options HC and H6)
Optional electronics modules for
the ST 3000 provides HART
Protocol compatibility in either
HART 5.x or 6.x formats.
Transmitters with a HART Option
are compatible with any HART
enabled system that provides 5.x
or 6.x format support.
FOUNDATION Fieldbus
(Option FF)
Equips transmitter with FF
protocol for use in 31.25 kbit/s FF
networks. See document 34-ST03-72 for additional information on
ST 3000 Fieldbus transmitters.
SIL2/SIL3 Certification
(Option SL)
This ST 3000 product is available
for use with safety systems. With
the SL option, we are fully certified
to SIL 2 capability for single
transmitters and SIL 3 capability for
multiple transmitter use through
TÜV Nord Sys Tec GmbH & Co.
KG. (continued)
We are in compliance with the
following SIL standards:
IEC 61508-1: 1998;
IEC 61508-2: 2000;
IEC 61508-3: 1998
NAMUR NE43 Compliance
(Option NE)
This option provides software the
meets the NAMUR NE43
requirements for failsafe software.
Transmitter failure information is
generated when the measuring
information is no longer valid.
Transmitter failure values are:
≤ 3.6 mA and ≥ 21.0 mA. The
normal ST 3000 ranges are ≤ 3.8
mA and ≥ 20.5 mA.
Indicator Configuration
(Option CI)
Provides custom configuration of
Smart Meters.
Tagging (Option TG)
Up to 30 characters can be added
on the stainless steel nameplate
mounted on the transmitter’s
electronics housing at no extra
cost. Note that a separate
nameplate on the meter body
contains the serial number and
body-related data. A stainless
steel wired on tag with additional
data of up to 4 lines of 28
characters is also available. The
number of characters for tagging
includes spaces.
Transmitter Configuration
(Option TC)
The factory can configure the
transmitter linear/square root
extraction, damping time, LRV,
URV and mode (analog/digital)
and enter an ID tag of up to eight
characters and scratchpad
information as specified.
Custom Calibration and ID in
Memory (Option CC)
The factory can calibrate any
range within the scope of the
transmitter’s range and enter an
ID tag of up to eight characters in
the transmitter’s memory.
Ordering Information
Contact your nearest Honeywell sales
office, or
In the U.S.:
Honeywell
Industrial Automation & Control
16404 North Black Canyon Hwy.
Phoenix, AZ 85053
1-800-288-7491
In Canada:
The Honeywell Centre
155 Gordon Baker Rd.
North York, Ontario M2H 3N7
1-800-461-0013
In Latin America:
Honeywell Inc.
480 Sawgrass Corporate Parkway,
Suite 200
Sunrise, FL 33325
(954) 845-2600
In Europe and Africa:
Honeywell S. A.
Avenue du Bourget 1
1140 Brussels, Belgium
In Eastern Europe:
Honeywell Praha,
s.r.o. Budejovicka 1
140 21 Prague 4,
Czech Republic
In the Middle East:
Honeywell Middle East Ltd.
Khalifa Street,
Sheikh Faisal Building
Abu Dhabi, U. A. E.
In Asia:
Honeywell Asia Pacific Inc.
Honeywell Building,
17 Changi Business Park Central 1
Singapore 486073
Republic of Singapore
In the Pacific:
Honeywell Pty Ltd.
5 Thomas Holt Drive
North Ryde NSW Australia 2113
(61 2) 9353 7000
In Japan:
Honeywell K.K.
14-6 Shibaura 1-chrome
Minato-ku, Tokyo, Japan 105-0023
Or, visit Honeywell on the World Wide
Web at: http://www.honeywell.com
Specifications are subject to change without
notice. (Note that specifications may differ
slightly for transmitters manufactured before
October 30, 1995.)
34-ST-03-57
Page 16
Model Selection Guide (34-ST-16-34)
Instructions
• Select the desired Key Number. The arrow to the right marks the selection available.
• Make one selection from each table, I and II, using the column below the proper arrow.
• Select as many Table III options as desired (if no options are desired, specify 9X).
• A (•) denotes unrestricted availability. A letter denotes restricted availability.
• Restrictions follow Table IV.
Key Number
______
I
-
___
II
- ____________
III (Optional)
-
_ _, _ _, _ _
IV
+
XXXX
KEY NUMBER
Description
0-25" to 0-2700" H2O/0-62.2 to 0-7000 mbar
Body Rating*: 750 psi (51.7 bar) Compound Characterized
0-20 to 0-500 psig/0-1.4 to 0-35 bar
Body Rating*: 500 psi (35 bar)
Selection
Avail.
STR93D
STR94G
* Remote seal system pressure rating is body rating or seal rating, whichever is less.
TABLE I - METER BODY
Description
1 Remote Seal (High Side)
2 Remote Seals
Number of Seals
1 Remote Seal (Low Side)
Value Added Model (VAM unit)
Silicone (DC 200)
Fill Fluid (Meter Body)
CTFE
Non-Wetted Material
Construction
316 SS
In-Line Gauge
316 SS for Close-Couple
Dual Head DP
Selection
1__
2__
3__
5__
_1_
_2_
Avail.
•
•
•
•
8
8
•
•
q
q
__A
__D
•
y
316 SS Heads
__A
•
316 SS Heads for Close-Couple connection
316 SS with all-welded meter body
__D
y
__C
7
34-ST-03-57
Page 17
TABLE II - SEALS
Format for Seal Selection:
Specify 12 characters
____________
Common
Availability
Required Seal
STR9xx
The first 3 characters are common to all seals.
When selecting required seal, you must specify
only the 9 selections within the required seal.
No Fill Fluid
Silicone (DC 200)
CTFE
Secondary Fill
Silicone (DC 704)
Neobee (M20) **
Syltherm 800 ***
Note:
No Capillary, No Nipple
5 feet
1.5 m
10 feet
3.0 m
15 feet
4.5 m
20 feet
6.1 m
25 feet
7.5 m
Connection of
35 feet
10.7 m
Capillary
Remote Seal to
Length
5 feet
1.5 m
Meter Body
10 feet
3.0 m
15 feet
4.5 m
20 feet
6.1 m
25 feet
7.5 m
35 feet
10.7 m
2 inch long SS nipple close-coupled
No Selection
0___________
1___________
2___________
3___________
4___________
5___________
SS Armor
PVC Coated SS Armor
No Seal Attached to Core Transmitter
p
3
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
z
z
•
•
___000000000
3
3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
•
•
•
9
3"
ANSI Class 150
ANSI Class 300
DIN DN80-PN40
_ _ _ AFA _ _ _ _ _ _
_ _ _ AFC _ _ _ _ _ _
_ _ _ AFM _ _ _ _ _ _
Selection
_ _ _ _ _ _ AA _ _ _ _
_ _ _ _ _ _ AB _ _ _ _
_ _ _ _ _ _ AC _ _ _ _
_ _ _ _ _ _ AE _ _ _ _
_ _ _ _ _ _ AF _ _ _ _
________1___
________2___
Calibration Rings
p
_0__________
_A__________
_B__________
_C__________
_D__________
_E__________
_F__________
_G__________
_H__________
_J__________
_K__________
_L__________
_M__________
_2__________
__0_________
3.5"
Seal-Capillary
Connection
•
•
•
Selection
Flange Material
3
•
•
p
Flange Pressure Rating *
Flush Flanged
Seal
3
p
Flange Size
Wetted Material
4G
•
Diaphragm
Diameter
Diaphragm
3D
Selection
Upper Insert
316 SS
316L SS
316 SS
Hastelloy C
Hastelloy C
Hastelloy C
Monel
Monel
Tantalum
Tantaluma
CS (Nickel Plated)
316 SS
_________1__
•
•
•
Side of Seal
_________2__
9
None
__________A_
•
•
316 SS
__________B_
5
5
Hastelloy C
Monel
__________C_
5
5
__________D_
5
5
Center of Seal
Table II continued next page
34-ST-03-57
Page 18
Availability
STR9xx
TABLE II - SEALS (continued)
Selection
3D
___________0
___________H
___________J
___________M
___________N
___________P
___________Q
___________R
___________S
•
•
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Description
Flushing
Connections
and Plugs**
Flush Flanged
Seal
Metal plug material
will be the same as
Lower material, if
metal plug is chosen (SS Plug for CS Lower
and Tantalum Clad)
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
4G
Table II continued below
*
**
***
****
a
Standard facing 125-250 AARH RF (raised face) serrated surface finish.
Limited vacuum availability.
Minimum static pressure requirement. No vacuum allowed. See Specification Figure 13.
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Tantalum Upper insert has Tantalum wetted parts and 316SS or CS non-wetted parts
STR9xx
TABLE II - SEALS (continued)
Flush Flanged
Seal with Lower
Const. - See
Diaphragm
Flange Pressure
Flange Size
Spec. Figure 34Diameter
Rating *
ST-03-57
ANSI
150
22
1"
ANSI
300
22
ANSI
150
22
1-1/2"
ANSI
300
22
2.4"
ANSI
150
22
2"
ANSI
300
22
ANSI
150
22
3"
ANSI
300
22
1/2"
ANSI
150
23
ANSI
150
23
1"
ANSI
300
23
ANSI
150
22
2.9"
1-1/2"
ANSI
300
22
ANSI
150
22
2"
ANSI
300
22
1/2"
ANSI
150
23
ANSI
150
23
1"
ANSI
300
23
ANSI
150
23
1-1/2"
ANSI
300
23
4.1"
ANSI
150
23
2"
ANSI
300
22
ANSI
150
22
3"
ANSI
300
22
3D
4G
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Selection
_ _ _ BCA _ _ _ _ _ _
_ _ _ BCC _ _ _ _ _ _
_ _ _ BGA _ _ _ _ _ _
_ _ _ BGC _ _ _ _ _ _
_ _ _ BDA _ _ _ _ _ _
_ _ _ BDC _ _ _ _ _ _
_ _ _ BFA _ _ _ _ _ _
_ _ _ BFC _ _ _ _ _ _
_ _ _ CAA _ _ _ _ _ _
_ _ _ CCA _ _ _ _ _ _
_ _ _ CCC _ _ _ _ _ _
_ _ _ CGA _ _ _ _ _ _
_ _ _ CGC _ _ _ _ _ _
_ _ _ CDA _ _ _ _ _ _
_ _ _ CDC _ _ _ _ _ _
_ _ _ DAA _ _ _ _ _ _
_ _ _ DCA _ _ _ _ _ _
_ _ _ DCC _ _ _ _ _ _
_ _ _ DGA _ _ _ _ _ _
_ _ _ DGC _ _ _ _ _ _
_ _ _ DDA _ _ _ _ _ _
_ _ _ DDC _ _ _ _ _ _
_ _ _ DFA _ _ _ _ _ _
_ _ _ DFC _ _ _ _ _ _
Table II continued next page
34-ST-03-57
Page 19
Availability
STR9xx
TABLE II - SEALS (continued)
Wetted Material
Non-Wetted Material
(upper, upper insert)
Bolts***
Flush Flanged
Flushing
Seal with Lower
Connections
(continued)
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen (SS Plug for CS Lower
and Tantalum Clad)
Gasket
Lower
316L SS
Hastelloy C
Hastelloy C
Monel
Tantalum
Tantalum
Tantalum
316 SS
316 SS
Hastelloy C
Monel
316 SS
Hastelloy C
Tantalum Clad
Upper
Upper Insert
316 SS
Carbon Steel
316 SS
316 SS
No Selection
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
Klinger C-4401
(non-asbestos)
Grafoil
Teflon
Gylon 3510
Selection
_ _ _ _ _ _ BA _ _ _ _
_ _ _ _ _ _ BB _ _ _ _
_ _ _ _ _ _ BC _ _ _ _
_ _ _ _ _ _ BE _ _ _ _
_ _ _ _ _ _ BF _ _ _ _
_ _ _ _ _ _ BG _ _ _ _
_ _ _ _ _ _ BH _ _ _ _
Selection
________4___
________5___
_________0__
__________0 _
__________H_
__________J _
__________M_
__________N_
__________P_
__________Q_
__________R_
__________S_
___________K
___________G
___________T
___________L
Diaphragm
Diameter
Flange Size
Flange Pressure Rating *
Selection
3"
2.8"
(2.8" OD
ANSI Class 150
ANSI Class 300
DIN DN80-PN40
ANSI Class 150
ANSI Class 300
DIN DN100-PN40
_ _ _ EFA _ _ _ _ _ _
_ _ _ EFC _ _ _ _ _ _
_ _ _ EFM _ _ _ _ _ _
_ _ _ FGA _ _ _ _ _ _
_ _ _ FGC _ _ _ _ _ _
_ _ _ FGP _ _ _ _ _ _
Selection
_ _ _ _ _ _ EA _ _ _ _
_ _ _ _ _ _ EB _ _ _ _
_ _ _ _ _ _ EC _ _ _ _
________7___
________8___
_________0__
__________2 _
__________4_
__________6_
extension)
4"
3.5"
(3.70" OD
extension)
Flange Seal with
Extended
Diaphragm
Diaphragm
Diaphragm
Wetted Material
Flange Material
Bolts
Extension Length
No Selection
Ext. Tube
316 SS
316L SS
Hastelloy C
316 SS
Hastelloy C
Hastelloy C
CS (Nickel Plated)
316 SS
No Selection
2"
4"
6"
No Selection
___________0
3D
4G
•
•
•
•
•
•
•
•
1
1
1
1
10
10
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
c
c
•
•
c
c
d
d
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Table II continued next page
*
**
***
Standard facing 125-250 AARH RF (raised face) serrated finish.
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Bolt material will be same as Upper Material. However, if Table III bolt/nut option chosen, seal bolt material will be the same.
34-ST-03-57
Page 20
STR9xx
TABLE II - SEALS (continued)
Diaphragm
Diameter
Flange Size
3.5"
3"
Flange Pressure Rating Dependent
on Customer Flange
ANSI Class 150/300/600
Diaphragm
Wetted Material
Non-Wetted Materials
No Selection
Body
316 SS
316L SS
316 SS
Hastelloy C
Hastelloy C
Hastelloy C
Monel
Monel
Tantalum
Tantaluma
No Selection
No Selection
Calibration Rings
Flushing
Connections
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen (SS Plug for CS Lower
and Tantalum Clad)
4G
•
•
•
•
•
•
•
•
•
•
1
1
•
•
•
Selection
_ _ _ GFA _ _ _ _ _ _
Selection
_ _ _ _ _ _ GA _ _ _ _
_ _ _ _ _ _ GB _ _ _ _
_ _ _ _ _ _ GC _ _ _ _
_ _ _ _ _ _ GE _ _ _ _
_ _ _ _ _ _ GG _ _ _ _
________0___
_________0_ _
__________A_
•
•
•
316 SS
__________B_
5
5
Hastelloy C
__________C_
5
5
Monel
__________D_
___________0
___________H
___________J
___________M
___________N
___________P
___________Q
___________R
___________S
5
5
None
Pancake Seal
3D
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
•
•
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3D
4G
Table II continued below
a
***
Tantalum Body has Tantalum wetted parts and 316SS non-wetted parts
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
STR9xx
TABLE II - SEALS (continued)
Chemical Tee
"Taylor" Wedge
Diaphragm
Diameter
Flange Size
Flange Pressure Rating
Selection
3.5"
Taylor
Wedge 5"
O.D.
750 psi
_ _ _ HM0 _ _ _ _ _ _
Wetted Material
Non-Wetted Material
Diaphragm
Body
316L SS
Hastelloy C
Hastelloy C
316 SS
316 SS
Hastelloy C
No Selection
Selection
_ _ _ _ _ _ HA _ _ _ _
_ _ _ _ _ _ HB _ _ _ _
_ _ _ _ _ _ HC _ _ _ _
________0___
Bolts
No Selection
_________0__
Styles
No Selection
No Selection
No Selection
__________0 _
___________0
v
•
•
•
•
•
•
•
Table II continued next page
34-ST-03-57
Page 21
Availability
STR9xx
TABLE II - SEALS (continued)
Diaphragm
Diameter
Seal Pressure
Threaded Process
Rating *
Connection Size
(NPT
304 SS
C.S. Bolts
Female)
Bolts
1/2" NPT
3/4" NPT
1" NPT
1/2" NPT
3/4" NPT
1" NPT
1/2" NPT
3/4" NPT
1" NPT
2.4"
2.9"
4.1"
Diaphragm
Wetted Material
Seal with
Threaded
Process
Connection
Non-Wetted Material
(upper)
Bolts***
Flushing
Connections
and Plugs**
Metal plug material
will be the same as
Lower material, if
metal plug is chosen (SS Plug for CS Lower
and Tantalum Clad)
Gasket
2500 psi 1250 psi
2500 psi 1250 psi
1500 psi 750 psi
Lower
316L SS
Carbon Steel
316 SS
316L SS
316 SS
Hastelloy C
Hastelloy C
Hastelloy C
Monel
Monel
Tantalum
316 SS
Hastelloy C
Tantalum
CS (Nickel Plated)
Stainless Steel
Carbon Steel
304 SS
None
One 1/4" with plastic plug
One 1/4" with metal plug
Two 1/4" with plastic plugs
Two 1/4" with metal plugs
One 1/2" with plastic plug
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
Klinger C-4401
(non-asbestos)
Grafoil
Teflon
Gylon 3510
3D
4G
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
1
1
1
Selection
_ _ _ JJG _ _ _ _ _ _
_ _ _ JKG _ _ _ _ _ _
_ _ _ JLG _ _ _ _ _ _
_ _ _ KJG _ _ _ _ _ _
_ _ _ KKG _ _ _ _ _ _
_ _ _ KLG _ _ _ _ _ _
_ _ _ LJG _ _ _ _ _ _
_ _ _ LKG _ _ _ _ _ _
_ _ _ LLG _ _ _ _ _ _
Selection
_ _ _ _ _ _ JA _ _ _ _
_ _ _ _ _ _ JB _ _ _ _
_ _ _ _ _ _ JC _ _ _ _
_ _ _ _ _ _ JD _ _ _ _
_ _ _ _ _ _ JE _ _ _ _
_ _ _ _ _ _ JF _ _ _ _
_ _ _ _ _ _ JG _ _ _ _
________A___
________C___
_________C__
_________D__
__________0 _
__________H_
__________J _
__________M_
__________N_
__________P_
__________Q_
__________R_
__________S_
___________K
___________G
___________T
___________L
•
•
w
w
1
1
•
•
•
•
•
•
•
•
•
•
•
•
11
11
11
11
11
11
11
11
c
c
•
•
c
c
d
d
Table II continued next page
* Caution:
Maximum working pressure of STR93D transmitter is 750 psi and STR94G transmitter
is 500 psig. Damage to sensor may result if pressure limit is exceeded.
**
Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
***
If Table III Bolt/Nut option is chosen, Seal bolts will ship as same material, and MAWP may change.
34-ST-03-57
Page 22
STR9xx
TABLE II - SEALS (continued)
Diaphragm
Diameter
Sanitary Seal
Flange Size
3D
4G
Selection
Pressure Rating
1.9"
2"
_ _ _ MD0 _ _ _ _ _ _
g
2.4"
2-1/2"
_ _ _ NE0 _ _ _ _ _ _
2.9"
3"
4.1"
4"
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
_ _ _ RFK _ _ _ _ _ _
•
•
_ _ _ RGK _ _ _ _ _ _
•
•
_ _ _ RPK _ _ _ _ _ _
•
•
_ _ _ RQK _ _ _ _ _ _
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wetted Material
Customer clamp rating or 600 psi,
whichever is less
_ _ _ PF0 _ _ _ _ _ _
Diaphragm
Body
_ _ _ QG0 _ _ _ _ _ _
Selection
316L SS
316 SS
______NA____
Non-Wetted Material
No Selection
________0___
Bolts
No Selection
_________0__
Styles
Tri-Clover Tri-Clamp
__________8 _
Gasket
No Selection
___________0
Seal Pressure Rating * *
Size and
Diaphragm
Diameter Bolt Pattern
Saddle Seal
C.S. Bolts
304 SS Bolts
1500 psi
2.4"
8-Bolt
Design
for 3" Pipe ?
4" pipe
1500 psi
2.4"
6-Bolt
Design
for 3" Pipe ?
4" pipe
1250 psi
Wetted Material
Non-Wetted Material
Diaphragm
Lower Housing
Selection
316L SS
Carbon Steel
_ _ _ _ _ _ RA _ _ _ _
316L SS
316 SS
_ _ _ _ _ _ RB _ _ _ _
Hastelloy C
316 SS
_ _ _ _ _ _ RC _ _ _ _
Hastelloy C
Hastelloy C
_ _ _ _ _ _ RD _ _ _ _
316L SS
N/A-Body Only
_ _ _ _ _ _ SB _ _ _ _
Hastelloy C
N/A-Body Only
Body
Bolts *, ***
_ _ _ _ _ _ SC _ _ _ _
Selection
Carbon Steel
316 SS
Gasket
Carbon Steel
________B___
1
1
304 SS
________C___
•
•
•
•
•
•
•
No Selection
_________0__
No Selection
Klinger C-4401
(non-asbestos)
Grafoil
Teflon
Gylon 3510
__________0 _
___________K
•
•
•
•
___________G
___________T
___________L
•
•
•
No Selection
Styles
1250 psi
Selection
*
Bolts are not included with "Body only" selection.
**
Caution:
Maximum working pressure of STR93D transmitter is 750 psi and STR94G transmitter
is 500 psig. Damage to sensor may result if pressure limit is exceeded.
***
If Table III Bolt/Nut option is chosen, Seal bolts will ship as same material, and MAWP may change.
34-ST-03-57
Page 23
STR9xx
TABLE III - OPTIONS
None
Communication Options
HART 5.x Protocol Compatible Electronics
HART 6.x Protocol Compatible Electronics
FOUNDATION Fieldbus Communications
Indicating Meter Options
Analog Meter (0-100 Even 0-10 Square Root)
Smart Meter
Custom Configuration of Smart Meter
Local Zero
Local Zero and Span
Transmitter Housing & Electronics Options
NAMUR Failsafe Software
SIL 2 - TÜV Certified transmitter (requires HC and WP options)
Lightning Protection
Custom Calibration and I.D. in Memory
Transmitter Configuration
Write Protection (Delivered in the "enabled" position)
Write Protection (Delivered in the "disabled" position)
316 SS Electronics Housing - with M20 Conduit Connections
1/2" NPT to M20 316SS Conduit Adapter (BASEEFA EEx d IIC)
1/2" NPT to 3/4" NPT 316 SS Conduit Adapter
Stainless Steel Housing with M20 to 1/2" NPT 316 SS Conduit
Adapter (use for FM and CSA Approvals)
Stainless Steel Customer Wired-On Tag
(4 lines, 28 characters per line, customer supplied information)
Stainless Steel Customer Wired-On Tag (blank)
End Cap Live Circuit Warning Label in Spanish (only with ATEX 3D)
End Cap Live Circuit Warning Label in Portuguese (only with ATEX 3D)
End Cap Live Circuit Warning Label in Italian (only with ATEX 3D)
End Cap Live Circuit Warning Label in German (only with ATEX 3D)
Selection
00
3D
4G
•
•
HC
H6
FF
e
e
r
e
e
r
b
ME
SM
CI
LZ
ZS
•
•
•
•
b
m
x
s
m
x
s
NE
SL
LP
CC
TC
WP
WX
SH
A1
A2
A3
15
14
15
14
•
•
•
•
•
•
•
•
•
•
n
n
u
i
n
n
u
i
TG
•
•
TB
SP
PG
TL
GE
•
•
a
a
a
a
a
a
a
a
CR
SS
B7
•
•
•
G1
G2
N1
N2
j
j
j
j
j
j
b
MB
SB
FB
•
•
•
•
•
•
b
b
b
b
Meter Body Options (Seal bolt material depends on Transmitter bolt material)
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts for Heads
316 SS Bolts and 316 SS Nuts for Process Heads
B7M Bolts and Nuts for Process Heads
Remote Seal Options
Gold Plated Seal Diaphragm (1 Seal)
Gold Plated Seal Diaphragm (2 Seals)
Teflon Coated Seal Diaphragm (1 Seal) - only for anti-sticking
Teflon Coated Seal Diaphragms(2 Seals) - only for anti-sticking
Transmitter Mounting Brackets Options
Mounting Bracket - Carbon Steel
Mounting Bracket - 304 SS
Flat Mounting Bracket
Services/Certificates Options
Users Manual Paper Copy (Standard, HC or FF ships accordingly)
Clean Transmitter & Seals for Oxygen or Chlorine Service with Certificate
Over-Pressure Leak Test with F3392 Certificate
Calibration Test Report and Certificate of Conformance (F3399)
Certificate of Conformance (F3391)
Certificate of Origin (F0195)
FMEDA Certificate (SIL 1)
NACE Certificate (F0198)
NACE Certificate (F0198) for welded meter bodies only
Marine Type Approvals (DNV, ABS, BV & LR)
Warranty Options
Additional Warranty - 1 year
Additional Warranty - 2 years
Additional Warranty - 3 years
Additional Warranty - 4 years
b
UM
0X
TP
F1
F3
F5
F6
F7
F8
MT
o
16
2
2
W1
W2
W3
W4
•
•
•
•
•
•
•
•
•
•
h
h
•
•
•
•
•
•
•
•
•
•
•
Table III continued next page
b
b
b
34-ST-03-57
Page 24
STR9xx
TABLE III - OPTIONS (continued)
Approval
Approval Type
Body
No hazardous location approvals
Explosion Proof
Dust Ignition Proof
Factory
Non-Incendive
Mutual
Intrinsically Safe
CSA
Explosion Proof
Dust Ignition Proof
Intrinsically Safe
Intrinsically Safe
SA
(Australia) Non-Sparking
Intrinsically Safe,
Zone 0/1
Flameproof, Zone 1
ATEX*
Non-Sparking,
Zone 2
Multiple Marking**
Int. Safe, Zone 0/1, or
Flameproof, Zone 1, or
Non-Sparking, Zone 2
INMETRO
Flameproof, Zone 1
(Brazil)
Location or Classification
Class I, Div. 1, Groups A,B,C,D
Class II, III Div. 1, Groups E,F,G
Class I, Div. 2, Groups A,B,C,D
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Class I, Div. 1, Groups B,C,D
Class II, III, Div. 1, Groups E,F,G
Class I, II, III, Div. 1, Groups
A,B,C,D,E,F,G
Ex ia IIC T4
Ex n IIC T6 (T4 with SM option)
EEx ia IIC T4, T5,T6
EEx d IIC T5, T6,
Enclosure IP 66/67
EEx nA, IIC T6
(Honeywell). Enclosure IP 66/67
Ex II 1 G EEx ia IIC T4, T5, T6
Ex II 2 G EEx d IIC T5, T6
Ex II 3 G EEx nA, IIC T6 (Honeywell)
Enclosure IP 66/67
Ex d IIC T5
3D
4G
9X
•
1C
•
•
2J
•
•
4G
•
•
3S
•
•
3D
•
•
3N
•
•
3H
•
•
6D
•
•
Selection
*See ATEX installation requirements in the ST 3000 User's Manual
**The user must determine the type of protection required for installation of the equipment. The user shall then check the box []
adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has been checked on
the nameplate, subsequently the equipment shall not be reinstalled using any of the other certification types.
TABLE IV
Factory Identification
XXXX
•
•
b
34-ST-03-57
Page 25
RESTRICTIONS
Restriction
Letter
Table
III
a
b
c
d
II
e
g
II
h
i
I, II
III
Available Only With
Not Available With
Selection
Table
Selection
3D or 3H
Select only one option from this group
_ _ _ _ _ _ BF _ _ _ _,
_ _ _ _ _ _ BG _ _ _ _,
_ _ _ _ _ _ BH _ _ _ _,
II
_ _ _ _ _ _ JF _ _ _ _,
_ _ _ _ _ _ JG _ _ _ _,
_ _ _ _ _ _ BF _ _ _ _,
_ _ _ _ _ _ BG _ _ _ _,
_ _ _ _ _ _ JF _ _ _ _,
_ _ _ _ _ _ JG _ _ _ _,
III
4G
_ A _ _ _ _ _ _ _ _ _ _,
_ B _ _ _ _ _ _ _ _ _ _,
_ C _ _ _ _ _ _ _ _ _ _,
_ G _ _ _ _ _ _ _ _ _ _,
_ H _ _ _ _ _ _ _ _ _ _,
_ J _ _ _ _ _ _ _ _ _ _,
_ 2 _ _ _ _ _ _ _ _ _ _,
_2_-2___________
1C or 2J
j
m
n
o
III
SM
III
CR
III
1C, 2J
II
p
q
II
_ _ _ _ _ _ AF _ _ _ _
_ _ _ _ _ _ BF _ _ _ _
_ _ _ _ _ _ BG _ _ _ _
_ _ _ _ _ _ BH _ _ _ _
_ _ _ _ _ _ GG _ _ _ _
_ _ _ _ _ _ JF _ _ _ _
_ _ _ _ _ _ JG _ _ _ _
II
DC704 and Syltherm 800
fills and close-couple require
SS seal upper.
_ _ _ BCA _ _ 5 _ _ _,
_ _ _ CAA _ _ 5 _ _ _,
_ _ _ CCA _ _ 5 _ _ _,
_ _ _ CCC _ _ 5 _ _ _,
_ _ _ DAA _ _ 5 _ _ _,
_ _ _ DCA _ _ 5 _ _ _,
_ _ _ DCC _ _ 5 _ _ _,
_ _ _ DGA _ _ 5 _ _ _,
_ _ _ DGC _ _ 5 _ _ _,
_ _ _ DDA _ _ 5 _ _ _,
_ _ _ _ _ _ GE _ _ _ _,
________A___
________B___
0 _ _ _ _ _ _ _ _ _ _ _ _,
2 _ _ _ _ _ _ _ _ _ _ _ _,
4____________
r
III
TC, ME, 4G, 3S
s
III
FF, ME
Restrictions continued next page
34-ST-03-57
Page 26
RESTRICTIONS - (continued)
Restriction
Available Only With
Letter
Selection
Table
III
1C, 2J
u
I
2__
v
w
x
Table
II
III
y
I
II
I
I
III
III
F7
FB
II
II
I
III
III
___________0
__________A_
1 _ _, 3 _ _
CR
CC,G1,G2,T1,T2,OX,TP,MT,WP
II
III
___________T
F7
_ _ _ _ _ _JJG_ _ _
_ _ _ _ _ _JKG_ _ _
_ _ _ _ _ _JLG_ _ _
_ _ _ _ _ _CAA_ _ _
_ _ _ _ _ _CCA_ _ _
_ _ _ _ _ _CCC_ _ _
FF, 00
FF
5 _ _, 1 _ _
8
9
II
_ _ _ _ _ _ AA2_ _ _
_ _ _ _ _ _ AB2_ _ _
10
II
__________0_
II
11
Notes:
MB, SB, FB
DC704 and Syltherm 800
fills and close-couple require
SS seal upper.
_ _ _ BCA _ _ 5 _ _ _,
_ _ _ CAA _ _ 5 _ _ _,
_ _ _ CCA _ _ 5 _ _ _,
_ _ _ CCC _ _ 5 _ _ _,
_ _ _ DAA _ _ 5 _ _ _,
_ _ _ DCA _ _ 5 _ _ _,
_ _ _ DCC _ _ 5 _ _ _,
_ _ _ DGA _ _ 5 _ _ _,
_ _ _ DGC _ _ 5 _ _ _,
_ _ _ DDA _ _ 5 _ _ _,
_ _ _ _ _ _ GE _ _ _ _,
________A___
________B___
2__
_A-M__________
__D
7
14
15
16
_ _ _ _ _ _ JA _ _ _ _
FF, SM
III
z
1
2
3
5
6
Not Available With
Selection
III
HC, WP
I
__C
III
III
See ST-83 for Published Specials with pricing.
See ST-89 and User's Manual for part numbers.
See COMS Order Entry Information including TC, manuals, certificates, drawings and SPINS.
See ST-OD-1 for tagging, ID, Transmitter Configuration (TC) and calibration including factory default values.
To request a quotation for a non-published "special", fax RFQ with Application Data Sheet (34-ST-18-01) to Marketing Applications.
34-ST-03-57
Page 27
Dimensions and drawings
20a
21a
21b
20b
20b
21b
20a
21a
20a
21a
20a
21a
20a
21a
21b
20b
20b
21b
20a
21a
20a
21a
20a
21a
20a
21a
21b
20b
20b
21b
20a
21a
20a
21a
20a
21a
20a
21a
21b
20b
20b
21b
20a
21a
20a
21a
20a
21a
Figure 21a.
20a. Flush Flanged Seal
Figure 21b.
20b. Flush Flanged Seal
34-ST-03-57
Page 28
Dimensions and drawings, cont.
Figure 22
21
Figure 23
22
34-ST-03-57
Page 29
Dimensions and drawings, cont.
Figure 24
23
Figure 25
24
Figure 26
25
34-ST-03-57
Page 30
Dimensions and drawings, cont.
Figure 27
26
Figure 28
27
34-ST-03-57
Page 31
Dimensions and drawings, cont.
Figure 29
28
Figure 30
29
Figure 31
30
Figure
20
34-ST-03-57
Page 32
ST 3000® is a registered trademark of Honeywell International Inc.
HART* is a trademark of the Hart Communication Foundation.
FOUNDATION™
is a trademark of the Fieldbus Foundation.
Honeywell Field Solutions
Honeywell International Inc.
2500 W. Union Hill Drive
Phoenix, Arizona 85027
©Honeywell International Inc.