MODEL: 95060COP
PACKING DIAGRAM
STYROFOAM: 12 KGS.
CI e88>-— Paris
| |
| ; [=— BACKPLATE ASSEMBLY
| —— GLASS SHADE
VA
7
DA 7 STYROFOAM: 12 KGS.
WIRE CONNECTOR
(3 PCS)
8/32 SCREWS,
SUPPLIED WITH BOX
OUNTING PLATE
2) NUTS
BACKPLATE
AVAILABLE PART IS: a BLACK
93080GS (GLASS SHADE)
_ EH
(2) 8/32 x 1-1/2"
SCREWS
SOCKET BLACK
— SUPPLY WIRE
BALL FINIAL 8
(2 PCS) A
f | > WHITE
SUPPLY WIRE
GLASS SHADE SL > SUPPLY
93080GS ATURE GROUND WIRE
(REPLACEMENT || GROUND UTLET BOX
PART) WIRE
GREEN
|| WHITE
FIXTURE WIRE WALL GROUND SCREW
( J
SOCKET RING т
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION: TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL.
IF YOU ARE REPLACING AN EXISTING FIXTURE, FIRST TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF POSITION.
SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES.
** IF YOU DO NOT HAVE ELECTRICAL WIRING EXPERIENCE, HAVE YOUR FIXTURE INSTALLED BY A QUALIFIED LICENSED
ELECTRICIAN.
¥** THIS FIXTURE IS TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE WEIGHT OF THIS FIXTURE.
THE OUTLET BOX MUST BE DIRECTLY SUPPORTED BY THE BUILDING STRUCTURE.
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT: SCREWDRIVER, PLIERS, ADJUSTABLE WRENCH.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE PACKAGE:
BACKPLATE ASSEMBLY, GLASS SHADE AND SOCKET RING. HARDWARE PACK: (2) 8/32 x 1—1/4" SCREWS, (3) WIRE
CONNECTORS. TO PROTECT THE FINISH, PLACE ALL PARTS ON A SOFT SURFACE.
INSTALL THE FIXTURE
1. REMOVE THE MOUNTING PLATE FROM BACK OF THE BACKPLATE ASSEMBLY BY UNSCREWING (2) BALL FINIALS.
2. ATTACH THE MOUNTING PLATE TO OUTLET BOX USING TWO SCREWS PROVIDED WITH THE OUTLET BOX. (NOTE: IF THE
SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4" SCREWS PROVIDED IN THE MOUNTING
HARDWARE PACKAGE).
3. CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON
WIRE CONNECTOR PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME
MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT
THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE CONNECTOR
PROVIDED.
4. RAISE BACKPLATE ASSEMBLY TO THE WALL AND CAREFULLY TUCK THE WIRES INSIDE THE OUTLET BOX. SPREAD THE
ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE
OTHER SIDE. LINE UP SCREWS WITH HOLES IN BACKPLATE AND SECURE WITH (2) BALL FINIALS.
5. PLACE GLASS SHADE OVER SOCKET AND SECURE WITH SOCKET RING.
6. INSTALL A 60 WATT MAXIMUM MEDIUM BASE TYPE “A” BULB INTO SOCKET.
UL
7. RESTORE POWER, YOUR NEW FIXTURE IS NOW READY TO USE. e
10/2013 93080COP INSTALLATION
">
