Dynex DX-GB5PRT 5-Port 10/100/1000 Gigabit Ethernet Switch Quick Setup Guide

DX-GB5PRT

5-Port Gigabit Ethernet Switch

Congratulations on your purchase of the DX-GB5PRT Dynex 5-Port

Gigabit Ethernet Switch. The DX-GB5PRT provides increased speed and backbone connections to make Gigabyte a reality.

Safety Notices

• Do not use this product near water, for example, in a wet basement or near a swimming pool.

• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

• Do not place heavy objects on the switch.

• Allow room for adequate ventilation.

Package contents

• DX-GB5PRT Dynex 5-Port Gigabit Ethernet Switch

• Quick Setup Guide

Features

• Complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.1p standards

• Five 10/100/1000M RJ45 ports

• Supports IEEE 802.1p QoS

• Support Green Ethernet technology to implement power saving features. (In Low Power Idle mode, up to 61.5% of the power can be saved.)

• Supports IEEE 802.3x flow control for full-duplex mode and backpressure for half-duplex mode

• Non-blocking switching architecture that forwards and filters packets at full wire-speed for maximum throughput

• 8K entry MAC address table of the DX-GB5PRT with auto-learning and auto-aging

• Supports for Jumbo frames of up to 15 KB

• LED indicators for monitoring power, link, and activity

Components

Front panel

Back panel

Power LED LEDs 1-5

Installing the switch

1 Connect the power adapter to the switch and power outlet.

Power cord

Power outlet

Switch

2 Connect the PC(s) and other device(s) to the switch.

3 Connect the switch to the Internet.

Internet

Internet Modem

4 Install complete connection.

Internet

PC

Router

Switch

Router

Switch

Network storage

Switch

Network storage

Modem PC

LED indicators

When the switch is plugged in and receiving power, the LED indicators respond as follows:

LED

Power

Link/Act

Ports 1-5

Status

On (green)

Off

On (orange)

Flashing (orange)

On (green)

Flashing (green)

Indication

Power on

No device is connected to the corresponding port.

A 10/100 Mbps device is connected to the corresponding port.

A 10/100 Mbps device is transmitting or receiving data through the corresponding port.

A 1000Mbps device is connected to the corresponding port.

A 1000Mbps device is transmitting or receiving data through the corresponding port.

Ports 1-5 Power port

QUICK SETUP GUIDE

Troubleshooting

1 The power LED is not lit

Make sure that the power adapter is connected correctly and the power outlet is supplying power.

2 The link/act LED is not lit when a device is connected to the corresponding port

Make sure that the cables are connected correctly and securely to the switch and device. Make sure that the cable is not longer than

328 ft. (100 m).

Specifications

Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,

Topology Star

Protocol CSMA/CD

Data transfer rate Ethernet: 10 Mbps (Half Duplex),

20 Mbps (Full Duplex)

Fast Ethernet: 100 Mbps (Half Duplex),

200 Mbps (Full Duplex)

Gigabit Ethernet: 2000 Mbps (Full Duplex)

Network media (cable) 10Base-T: UTP category 3, 4, 5 cable

EIA/TIA-568 100Ω STP (maximum 100 m)

100Base-TX: UTP category 5, 5e cable

EIA/TIA-568 100Ω STP (maximum 100 m)

1000Base-TX: UTP category 5e, 6 cable

Legal notices

FCC statement

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more or the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

One-Year Limited Warranty

Visit www.dynexproducts.com for details.

Number of ports

EIA/TIA-568 100Ω STP (maximum 100 m)

Five 10/100/1000M RJ45 ports

Contact Dynex

For customer service please call 800-305-2204 www.dynexproducts.com

Transfer method Store-and-Forward

MAC address learning

Frame filter rate

Frame forward rate

Automatic learning and aging

10Base-T: 14880 pps/Port

Distributed by Best Buy Purchasing, LLC

7601 Penn Avenue South, Richfield, MN USA 55423-3645

© 2010 BBY Solutions, Inc. All Rights Reserved.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All

1488000

10Base-T: 14880 pps/Port

ENGLISH 10-1123