HOME
DECORATORS
COLLECTION
BF-25326 FREMONT MIRROR WALL CABINET
INV#29442
ASSEMBLY INSTRUCTIONS
Made In China
MAX LOAD: 30LBS
€
N
1/11
Thank you for purchasing this quality product. Be sure to check all
packing material carefully for small parts, which may have came
loose inside the carton during shipment. Count all parts and
material hardware, then compare with parts list to be sure all parts
are present. If any parts are missing or damaged, phone, fax, or
mail to our Custormer Service Department for efficient and speedy
service. Please indicate the model number and code letter of part(s)
needed.
IMPORTANT NOTE: Follow instructions listed below in proper sequence as
numbered to assure fast, easy and correct assembly.
STRUCTURAL DIAGRAM
H \ = © A
\ Mar
o D
° | Z A
, 17 |
/ С
E == 27 ||
2/11
PARTS LIST
27
TOP PANEL-1PC
Ne
LEFT SIDE PANEL-1PC
C
I~
RIGHT SIDE PANEL-1PC
ADORNING PANEL-1PC
E
SHELVES-2PCS
F
BOTTOM PANEL-1PC
G
BACK PANEL-1PC
H
DOOR-1PC
I
CAM-TOOL-1PC
J
A
CAM-BOLTS-1 0PCS
CAM-LOCKS-1 OPCS
L
Tmm x 5/8"
x
SCREWS-14PCS
HINGES-2PCS
N Tmm x 5/8"
y
SCREWS-12PCS
0
HANDLE-1PC
P
8mm x 5/8"
2
SCREW-1PC
Q
IN
SHELF SUPPORTS-8PCS
R
CECI
La
1
MAGNET-1PC
S
6mm x 5/8"
vw
SCREWS-5PCS
o |
J
SHEET IRONS-2PCS
3/11
U 7mm x 7/8"
vw
SCREWS-5PCS
\
— <<
О
GECKOS-SPCS
W
emm x 1"
SCREWS-2PCS
ED
FEMALE MAGNET-1PC
Y 5mmx 1/2"
y
SCREW-1PC
Z
EVA MATS-2PCS
AT
“№
DOWELS—2PCS
NOTE: THE SURFACE WITH THE STICKER IS THE BACK SIDE.
4/11
NOTE: e UPON OPENING, THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT. IN ORDER
TO PREVENT DAMAGE DURING ASSEMBLY, PLEASE ASSEMBLE THIS ITEM WITH AT
LEAST TWO PEOPLE.
NOTE: TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
HOW TO USE THE CAM- TOOL
NOTE: e THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
5/11
1) . ASSEMBLE THE MAGNET (R).
® ATTACH THE MAGNET(R) TO ADORNING PANEL (D) USING 2 SCREWS (W).
2) . ASSEMBLE THE RIGHT SIDE PANEL(C).
® ROTATE 3 CAM-BOLTS(J) INTO THE HOLES IN THE RIGHT SIDE PANEL(C).
e PLACE THE CAM-BOLTS(J) INTO THE HOLES IN THE PANEL (D/F) AND ATTACH USING 3
CAM- LOCKS (K) .
6/11
3) . ASSEMBLE THE LEFT SIDE PANEL(B).
® ROTATE 3 CAM-BOLTS(J) INTO THE HOLES IN THE LEFT SIDE PANEL(B).
e PLACE THE CAM-BOLTS(J) INTO THE HOLES IN THE PANEL (D/F) AND ATTACH USING 3
CAM- LOCKS (K) .
AO
on oi &
O D
rd
4) . ASSEMBLE THE TOP PANEL (A).
e INSERT 2 DOWELS(A1) INTO THE HOLES IN THE ADRNING PANEL (D).
® ROTATE 4 CAM-BOLTS(J) INTO THE HOLES IN THE TOP PANEL(A).
e PLACE THE CAM-BOLTS(J) INTO THE HOLES IN THE PANEL (B/C) AND ATTACH USING 4
CAM- LOCKS (K) .
7/11
pr HS
5) . ASSEMBLE THE BACK PANEL (G).
® ATTACH THE BACK PANEL (G) USING 14 SCREWS(L).
| "k
6) . ASSEMBLE THE DOOR(H).
e ATTACH THE FRMALE MAGNET(X) TO DOOR(H) USING 1 SCREW(Y).
e ATTACH THE HANDLE(0) TO DOOR(H) USING 1 SCREW(P).
e ATTACH THE HINGES(M) TO DOOR(H) USING 6 SCREWS(N).
8/11
D
\ | A
~~
o A
7). ASSEMBLE THE SHEETIRON(T).
e ATTACH THE SHEETIRON(T) TO TOP PANEL(A) USING 5 SCREWS(S).
e ATTACH THE EVA MATS(Z) TO BACK PANEL(G).
©
©
©
X >
Le + ®/
Z e #
Lo E
>
8) . ASSEMBLE THE DOOR (H).
® ATTACH THE DOOR(H) TO RIGHT SIDE PANEL(C) USING 6 SCREWS(N).
9/11
© >
>
9) . ASSEMBLE THE SHELF SUPPORTS(Q).
e INSERT 8 SHELF SUPPORTS(Q) INTO THE HOLES IN THE SIDE PANEL (B/C).
10). ASSEMBLE THE SHELVES(E).
e PUT THE SHELVES(E) ONTO THE SHELF SUPPORTS(Q).
10/11
11 ) . ASSEMBLE THE SHEETIRON(T).
® DRILL 5 HOLES INTO THE WALL, PLEASE REFER TO THE REAR BACK PANEL'S HOLE DISTANCE
AND HEIGHT.
® TAP 5 GECKOS(V) INTO THE HOLES ON THE WALL. THEN ROTATE 5 SCREWS(U) INTO THE
GECKOS (V).
® HANG THE CABINET ONTO THE SHEETIRONS(T).
11/11
">
